PIC24HJ256GPX06A/X08A/X10A PIC24HJ256GPX06A/X08A/X10A Family Silicon Errata and Data Sheet Clarification The PIC24HJ256GPX06A/X08A/X10A family devices that you have received conform functionally to the current Device Data Sheet (DS70592C), except for the anomalies described in this document. For example, to identify the silicon revision level using MPLAB IDE in conjunction with MPLAB ICD 3 or PICkitTM 3: 1. The silicon issues discussed in the following pages are for silicon revisions with the Device and Revision IDs listed in Table 1. The silicon issues are summarized in Table 2. 2. The errata described in this document will be addressed in future revisions of the PIC24HJ256GPX06A/X08A/ X10A silicon. Note: 3. 4. This document summarizes all silicon errata issues from all revisions of silicon, previous as well as current. Only the issues indicated in the last column of Table 2 apply to the current silicon revision (A3). Note: Data Sheet clarifications and corrections start on page 6, following the discussion of silicon issues. SILICON DEVREV VALUES Part Number PIC24HJ256GP206A Device ID(1) 0x0773 PIC24HJ256GP610A 0x077B 2: Revision ID for Silicon Revision(2) A2 A3 0x3002 0x3003 0x0771 PIC24HJ256GP210A Note 1: If you are unable to extract the silicon revision level, please contact your local Microchip sales office for assistance. The Device and Revision ID values for the various PIC24HJ256GPX06A/X08A/X10A silicon revisions are shown in Table 1. The silicon revision level can be identified using the current version of MPLAB(R) IDE and Microchip's programmers, debuggers and emulation tools, which are available at the Microchip corporate web site (www.microchip.com). TABLE 1: Using the appropriate interface, connect the device to the MPLAB ICD 3 programmer/debugger or PICkit 3. From the main menu in MPLAB IDE, select Configure>Select Device, and then select the target part number in the dialog box. Select the MPLAB hardware tool (Debugger>Select Tool). Perform a "Connect" operation to the device (Debugger>Connect). Depending on the development tool used, the part number and Device Revision ID value appear in the Output window. The Device and Revision IDs (DEVID and DEVREV) are located at the last two implemented addresses in program memory. Refer to the "dsPIC33F/PIC24H Flash Programming Specification" (DS70152) for detailed information on Device and Revision IDs for your specific device. (c) 2009-2011 Microchip Technology Inc. DS80482F-page 1 PIC24HJ256GPX06A/X08A/X10A TABLE 2: Module SILICON ISSUE SUMMARY Feature Item Number Affected Revisions(1) Issue Summary A2 A3 X ECANTM WAKIF bit 1. The WAKIF bit in the CxINTF register cannot be cleared by software instruction after the device is interrupted from Sleep due to activity on the CAN bus. X ECAN DMA 2. False DMA Error Traps may be generated in applications that perform both transmissions and receptions using ECAN with DMA. X UART Break Characters 3. The UART module will not generate consecutive break characters. X X ADC DONE bit 4. The ADC Conversion Status bit (DONE) does not work when External Interrupt is selected as the ADC trigger source. X X SPI TBF bit 5. Writing to the SPIBUF register as soon as the TBF bit is cleared will cause the SPI module to ignore the written data. X X DMA Controller CPU Write Collision Detection 6. DMA CPU write collisions will not be detected. ADC Current Consumption in Sleep Mode 7. If the ADC module is in an enabled state when the device enters Sleep mode, the power-down current (IPD) of the device may exceed the device data sheet specifications. X X All 150C Operation 8. Affected revisions of silicon only support 140C operation instead of 150C for extended operating temperature. X X CPU Interrupt Disable 9. When a previous DISI instruction is active (i.e., the DISICNT register is non-zero), and the value of the DISICNT register is updated manually, the DISICNT register freezes and disables interrupts permanently. X X CPU div.sd 10. When using the div.sd instruction, the overflow bit is not getting set when an overflow occurs. X X UART TX Interrupt 11. A transmit (TX) Interrupt may occur before the data transmission is complete. X X JTAG Flash Programming 12. JTAG Flash programming is not supported. X X Note 1: X Only those issues indicated in the last column apply to the current silicon revision. DS80482F-page 2 (c) 2009-2011 Microchip Technology Inc. PIC24HJ256GPX06A/X08A/X10A Silicon Errata Issues Note: This document summarizes all silicon errata issues from all revisions of silicon, previous as well as current. Only the issues indicated by the shaded column in the following tables apply to the current silicon revision (A3). 1. Module: ECANTM The WAKIF bit in the CxINTF register cannot be cleared by software instruction after the device is interrupted from Sleep due to activity on the CAN bus. When the device wakes up from Sleep due to CAN bus activity, the ECAN module is placed in operational mode. The ECAN Event interrupt occurs due to the WAKIF flag. Trying to clear the flag in the Interrupt Service Routine (ISR) may not clear the flag. The WAKIF bit being set will not cause repetitive Interrupt Service Routine execution. Work around Although the WAKIF bit does not clear, the device Sleep and ECAN Wake functions continue to work as expected. If the ECAN event is enabled, the CPU will enter the Interrupt Service Routine due to the WAKIF flag getting set. The application can maintain a secondary flag, which tracks the device Sleep and Wake events. Affected Silicon Revisions A2 A3 X X 2. Module: ECAN In user applications that perform both transmissions and receptions using ECAN with DMA, intermittent DMA Write Collisions might get generated, resulting in the generation of DMA Error Traps. The ECAN messages would be transmitted and received correctly even when these DMA Error Traps occur. Work around Within the DMA Error Trap service routine in the application software, read the DMACS0 register and inspect the two XWCOLn (n = 0, 1, ...,7) bits corresponding to the DMA channels being used for ECAN transmission and reception. For example, if DMA Channel 1 is used for ECAN Reception and DMA Channel 2 is used for ECAN Transmission, inspect the XWCOL1 and XWCOL2 bits. If either of these bits is found to be set, clear the DMACERR bit in the INTCON1 register and return from the DMA Error Trap service routine. Affected Silicon Revisions A2 A3 X 3. Module: UART The UART module will not generate consecutive break characters. Trying to perform a back-to-back Break character transmission will cause the UART module to transmit the dummy character used to generate the first Break character instead of transmitting the second Break character. Break characters are generated correctly if they are followed by non-Break character transmission. Work around None. Affected Silicon Revisions (c) 2009-2011 Microchip Technology Inc. A2 A3 X X DS80482F-page 3 PIC24HJ256GPX06A/X08A/X10A 4. Module: ADC The ADC Conversion Status (DONE) bit (ADxCON1<0>) does not indicate completion of conversion when External Interrupt is selected as the ADC trigger source (ADxCON1<SSRC> = 1). Work around Use an ADC interrupt or poll ADxIF bit in the IFSx registers to determine the completion of conversion. Affected Silicon Revisions A2 A3 X X 5. Module: SPI Writing to the SPIxBUF register as soon as the TBF bit is cleared will cause the SPI module to ignore the written data. Applications that use SPI with DMA are not affected by this erratum. Work around After the TBF bit is cleared, wait for a minimum duration of one SPI clock before writing to the SPIxBUF register. 7. Module: ADC If the ADC module is in an enabled state when the device enters Sleep mode as a result of executing a PWRSAV #0 instruction, the device power-down current (IPD) may exceed the specifications listed in the device data sheet. This may happen even if the ADC module is disabled by clearing the ADON bit prior to entering Sleep mode. Work around In order to remain within the IPD specifications listed in the device data sheet, the user software must completely disable the ADC module by setting the ADC Module Disable bit in the corresponding Peripheral Module Disable register (PMDx), prior to executing a PWRSAV #0 instruction. Affected Silicon Revisions A2 A3 X X 8. Module: All The affected silicon revisions listed below are not warranted for operation at 150C. Alternatively, do one of the following: Work around * Poll the RBF bit and wait for it to get set before writing to the SPIxBUF register * Poll the SPI Interrupt flag and wait for it to get set before writing to the SPIxBUF register * Use an SPI Interrupt Service Routine * Use DMA Only use the affected revisions of silicon for Hi-Temp operating range from -40C to +140C. Affected Silicon Revisions A2 A3 X X Affected Silicon Revisions A2 A3 X X 6. Module: DMA Controller DMA CPU write collisions will not be detected, and the corresponding XWCOLn bit (n = 0, 1, ..., 7) will not be set. As a result, a CPU write collision event will not generate a DMA Error Trap. Work around None. Before writing to any memory location in DMA RAM, ensure that none of the enabled DMA channels is using the same memory location for data transfers from a peripheral. 9. Module: CPU When a previous DISI instruction is active (i.e., the DISICNT register is non-zero), and the value of the DISICNT register is updated manually, the DISICNT register freezes and disables interrupts permanently. Work around Avoid updating the DISICNT register manually. Instead, use the DISI #n instruction with the required value for `n'. Affected Silicon Revisions A2 A3 X X Affected Silicon Revisions A2 A3 X DS80482F-page 4 (c) 2009-2011 Microchip Technology Inc. PIC24HJ256GPX06A/X08A/X10A 10. Module: CPU When using the Signed 32-by-16-bit Division instruction, div.sd, the overflow bit does not always get set when an overflow occurs. Work around Test for and handle overflow conditions outside of the div.sd instruction. Affected Silicon Revisions A2 A3 X X 11. Module: UART When using UTXISEL = 01 (Interrupt when last character is shifted out of the Transmit Shift Register) and the final character is being shifted out through the Transmit Shift Register, the Transmit (TX) Interrupt may occur before the final bit is shifted out. Work around If it is critical that the interrupt processing occur only when all transmit operations are complete. Hold off the interrupt routine processing by adding a loop at the beginning of the routine that polls the Transmit Shift Register Empty bit (TRMT) before processing the rest of the interrupt. Affected Silicon Revisions A2 A3 X X 12. Module: JTAG JTAG Flash programming is not supported. Work around None. Affected Silicon Revisions A2 A3 X X (c) 2009-2011 Microchip Technology Inc. DS80482F-page 5 PIC24HJ256GPX06A/X08A/X10A Data Sheet Clarifications The following typographic corrections and clarifications are to be noted for the latest version of the device data sheet (DS70592C): Note: Corrections are shown in bold. Where possible, the original bold text formatting has been removed for clarity. No issues to report at this time. DS80482F-page 6 (c) 2009-2011 Microchip Technology Inc. PIC24HJ256GPX06A/X08A/X10A APPENDIX A: REVISION HISTORY Rev A Document (9/2009) Initial release of this document; issued for revision A2 silicon. Includes silicon issues 1-2 (ECANTM), 3 (UART), 4 (ADC) and 5 (SPI). Rev B Document (12/2009) Added Rev. A3 silicon information. Added silicon issue 6 (DMA Controller). Rev C Document (6/2010) Added silicon issue 7 (ADC) and data sheet clarification 1 (DC Characteristics: I/O Pin Input Specifications). Rev D Document (9/2010) Added silicon issue 8 (All). Rev E Document (3/2011) Removed data sheet clarification 1. Rev F Document (11/2011) Added silicon issues 9 (CPU), 10 (CPU), 11 (UART), and 12 (JTAG). (c) 2009-2011 Microchip Technology Inc. DS80482F-page 7 PIC24HJ256GPX06A/X08A/X10A NOTES: DS80482F-page 8 (c) 2009-2011 Microchip Technology Inc. Note the following details of the code protection feature on Microchip devices: * Microchip products meet the specification contained in their particular Microchip Data Sheet. * Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the intended manner and under normal conditions. * There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip's Data Sheets. Most likely, the person doing so is engaged in theft of intellectual property. * Microchip is willing to work with the customer who is concerned about the integrity of their code. * Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not mean that we are guaranteeing the product as "unbreakable." Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our products. Attempts to break Microchip's code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act. Information contained in this publication regarding device applications and the like is provided only for your convenience and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. MICROCHIP MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED, WRITTEN OR ORAL, STATUTORY OR OTHERWISE, RELATED TO THE INFORMATION, INCLUDING BUT NOT LIMITED TO ITS CONDITION, QUALITY, PERFORMANCE, MERCHANTABILITY OR FITNESS FOR PURPOSE. Microchip disclaims all liability arising from this information and its use. Use of Microchip devices in life support and/or safety applications is entirely at the buyer's risk, and the buyer agrees to defend, indemnify and hold harmless Microchip from any and all damages, claims, suits, or expenses resulting from such use. No licenses are conveyed, implicitly or otherwise, under any Microchip intellectual property rights. Trademarks The Microchip name and logo, the Microchip logo, dsPIC, KEELOQ, KEELOQ logo, MPLAB, PIC, PICmicro, PICSTART, PIC32 logo, rfPIC and UNI/O are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. FilterLab, Hampshire, HI-TECH C, Linear Active Thermistor, MXDEV, MXLAB, SEEVAL and The Embedded Control Solutions Company are registered trademarks of Microchip Technology Incorporated in the U.S.A. Analog-for-the-Digital Age, Application Maestro, chipKIT, chipKIT logo, CodeGuard, dsPICDEM, dsPICDEM.net, dsPICworks, dsSPEAK, ECAN, ECONOMONITOR, FanSense, HI-TIDE, In-Circuit Serial Programming, ICSP, Mindi, MiWi, MPASM, MPLAB Certified logo, MPLIB, MPLINK, mTouch, Omniscient Code Generation, PICC, PICC-18, PICDEM, PICDEM.net, PICkit, PICtail, REAL ICE, rfLAB, Select Mode, Total Endurance, TSHARC, UniWinDriver, WiperLock and ZENA are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. All other trademarks mentioned herein are property of their respective companies. (c) 2009-2011, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved. Printed on recycled paper. ISBN: 978-1-61341-817-8 Microchip received ISO/TS-16949:2009 certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona; Gresham, Oregon and design centers in California and India. The Company's quality system processes and procedures are for its PIC(R) MCUs and dsPIC(R) DSCs, KEELOQ(R) code hopping devices, Serial EEPROMs, microperipherals, nonvolatile memory and analog products. In addition, Microchip's quality system for the design and manufacture of development systems is ISO 9001:2000 certified. (c) 2009-2011 Microchip Technology Inc. DS80482F-page 9 Worldwide Sales and Service AMERICAS ASIA/PACIFIC ASIA/PACIFIC EUROPE Corporate Office 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7200 Fax: 480-792-7277 Technical Support: http://www.microchip.com/ support Web Address: www.microchip.com Asia Pacific Office Suites 3707-14, 37th Floor Tower 6, The Gateway Harbour City, Kowloon Hong Kong Tel: 852-2401-1200 Fax: 852-2401-3431 India - Bangalore Tel: 91-80-3090-4444 Fax: 91-80-3090-4123 India - New Delhi Tel: 91-11-4160-8631 Fax: 91-11-4160-8632 Austria - Wels Tel: 43-7242-2244-39 Fax: 43-7242-2244-393 Denmark - Copenhagen Tel: 45-4450-2828 Fax: 45-4485-2829 India - Pune Tel: 91-20-2566-1512 Fax: 91-20-2566-1513 France - Paris Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79 Japan - Yokohama Tel: 81-45-471- 6166 Fax: 81-45-471-6122 Germany - Munich Tel: 49-89-627-144-0 Fax: 49-89-627-144-44 Atlanta Duluth, GA Tel: 678-957-9614 Fax: 678-957-1455 Boston Westborough, MA Tel: 774-760-0087 Fax: 774-760-0088 Chicago Itasca, IL Tel: 630-285-0071 Fax: 630-285-0075 Cleveland Independence, OH Tel: 216-447-0464 Fax: 216-447-0643 Dallas Addison, TX Tel: 972-818-7423 Fax: 972-818-2924 Detroit Farmington Hills, MI Tel: 248-538-2250 Fax: 248-538-2260 Indianapolis Noblesville, IN Tel: 317-773-8323 Fax: 317-773-5453 Los Angeles Mission Viejo, CA Tel: 949-462-9523 Fax: 949-462-9608 Santa Clara Santa Clara, CA Tel: 408-961-6444 Fax: 408-961-6445 Toronto Mississauga, Ontario, Canada Tel: 905-673-0699 Fax: 905-673-6509 Australia - Sydney Tel: 61-2-9868-6733 Fax: 61-2-9868-6755 China - Beijing Tel: 86-10-8569-7000 Fax: 86-10-8528-2104 China - Chengdu Tel: 86-28-8665-5511 Fax: 86-28-8665-7889 Netherlands - Drunen Tel: 31-416-690399 Fax: 31-416-690340 China - Chongqing Tel: 86-23-8980-9588 Fax: 86-23-8980-9500 Korea - Seoul Tel: 82-2-554-7200 Fax: 82-2-558-5932 or 82-2-558-5934 China - Hangzhou Tel: 86-571-2819-3187 Fax: 86-571-2819-3189 Malaysia - Kuala Lumpur Tel: 60-3-6201-9857 Fax: 60-3-6201-9859 China - Hong Kong SAR Tel: 852-2401-1200 Fax: 852-2401-3431 Malaysia - Penang Tel: 60-4-227-8870 Fax: 60-4-227-4068 China - Nanjing Tel: 86-25-8473-2460 Fax: 86-25-8473-2470 Philippines - Manila Tel: 63-2-634-9065 Fax: 63-2-634-9069 China - Qingdao Tel: 86-532-8502-7355 Fax: 86-532-8502-7205 Singapore Tel: 65-6334-8870 Fax: 65-6334-8850 China - Shanghai Tel: 86-21-5407-5533 Fax: 86-21-5407-5066 Taiwan - Hsin Chu Tel: 886-3-5778-366 Fax: 886-3-5770-955 China - Shenyang Tel: 86-24-2334-2829 Fax: 86-24-2334-2393 Taiwan - Kaohsiung Tel: 886-7-536-4818 Fax: 886-7-330-9305 China - Shenzhen Tel: 86-755-8203-2660 Fax: 86-755-8203-1760 Taiwan - Taipei Tel: 886-2-2500-6610 Fax: 886-2-2508-0102 China - Wuhan Tel: 86-27-5980-5300 Fax: 86-27-5980-5118 Thailand - Bangkok Tel: 66-2-694-1351 Fax: 66-2-694-1350 Spain - Madrid Tel: 34-91-708-08-90 Fax: 34-91-708-08-91 UK - Wokingham Tel: 44-118-921-5869 Fax: 44-118-921-5820 China - Xian Tel: 86-29-8833-7252 Fax: 86-29-8833-7256 China - Xiamen Tel: 86-592-2388138 Fax: 86-592-2388130 China - Zhuhai Tel: 86-756-3210040 Fax: 86-756-3210049 DS80482F-page 10 Italy - Milan Tel: 39-0331-742611 Fax: 39-0331-466781 Korea - Daegu Tel: 82-53-744-4301 Fax: 82-53-744-4302 08/02/11 (c) 2009-2011 Microchip Technology Inc.