Notice for TAIYO YUDEN products Please read this notice before using the TAIYO YUDEN products. REMINDERS Product information in this catalog is as of October 2011. All of the contents specified herein are subject to change without notice due to technical improvements, etc. Therefore, please check for the latest information carefully before practical application or usage of the Products. Please note that Taiyo Yuden Co., Ltd. shall not be responsible for any defects in products or equipment incorporating such products, which are caused under the conditions other than those specified in this catalog or individual specification. Please contact Taiyo Yuden Co., Ltd. for further details of product specifications as the individual specification is available. Please conduct validation and verification of products in actual condition of mounting and operating environment before commercial shipment of the equipment. All electronic components or functional modules listed in this catalog are developed, designed and intended for use in general electronics equipment.(for AV, office automation, household, office supply, information service, telecommunications, (such as mobile phone or PC) etc.). Before incorporating the components or devices into any equipment in the field such as transportation,( automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network (telephone exchange, base station) etc. which may have direct influence to harm or injure a human body, please contact Taiyo Yuden Co., Ltd. for more detail in advance. Do not incorporate the products into any equipment in fields such as aerospace, aviation, nuclear control, submarine system, military, etc. where higher safety and reliability are especially required. In addition, even electronic components or functional modules that are used for the general electronic equipment, if the equipment or the electric circuit require high safety or reliability function or performances, a sufficient reliability evaluation check for safety shall be performed before commercial shipment and moreover, due consideration to install a protective circuit is strongly recommended at customer's design stage. The contents of this catalog are applicable to the products which are purchased from our sales offices or distributors (so called"TAIYO YUDEN' s official sales channel"). It is only applicable to the products purchased from any of TAIYO YUDEN's official sales channel. Please note that Taiyo Yuden Co., Ltd. shall have no responsibility for any controversies or disputes that may occur in connection with a third party's intellectual property rights and other related rights arising from your usage of products in this catalog. Taiyo Yuden Co., Ltd. grants no license for such rights. Caution for export Certain items in this catalog may require specific procedures for export according to"Foreign Exchange and Foreign Trade Control Law"of Japan,"U.S. Export Administration Regulations", and other applicable regulations. Should you have any question or inquiry on this matter, please contact our sales staff. 12 notice_e-01 WIRE-WOUND CHIP INDUCTORS (LB SERIES) REFLOW FEATURES APPLICATIONS LB-series are Wound Chip Inductors having wide line-up, which are suitable for any circuit designs. They are suitable for an anti-noise measure on the power supply circuit of DSC, DVC, HDD, LCD-TV, mobile phones,PC, game equipments, various communication equipments and etc.. LBC series has large rated current. They contribute to the miniaturization of the power supply circuit. OPERATING TEMP. LBR series has low DC resistance. They contribute to the miniaturization of the power supply circuit. 40 105Including-self-generated heat LBMF series has a low loss characteristic. ORDERING CODE B L LB 2 1 2 T Type Wound chip inductor C R MF 0 0 External Dimensions mm 1608 0603 1.6x0.8 2012 0805 2.0x1.25 2016 0806 2.0x1.6 2518 1007 2.5x1.8 3218 1207 3.2x1.8 3225 1210 3.2x2.5 Shape Standard products High current Low Rdc Low loss 1 T 0 Packaging Tape & Reel Nominal InductanceH example 1R0 1 100 10 101 100 R=decimal point Inductance Tolerances K 10 M 20 Special code Standard products Low Rdc R type Internal code EXTERNAL DIMENSIONS/STANDARD QUANTITY EXTERNAL DIMENSIONS Type C A TYPE 1608 MF1608 2012 2016 2518 3218 3225 A 0.55 0.55 0.60 0.60 0.60 0.85 0.85 B 0.7 0.7 1.0 1.0 1.5 1.7 1.7 Unitmm C 0.9 1.0 1.45 1.8 2.0 2.0 2.7 B L T Standard Quantity [pcs] Paper Embossed Tape Tape e LB1608 1.60.1 0.80.1 0.80.1 0.350.15 0.0630.004 0.0310.004 0.0310.004 0.0140.006 4000 LBMF1608 1.60.2 0.80.2 0.80.2 0.450.15 0.0630.008 0.0310.008 0.0310.008 0.0160.006 3000 LB2012 LBC2012 LBR2012 2.00.2 1.250.2 1.250.2 0.50.2 0.0790.008 0.0490.008 0.0490.008 0.0200.008 3000 LB2016 LBC2016 2.00.2 1.60.2 1.60.2 0.50.2 0.0790.008 0.0630.008 0.0630.008 0.0200.008 2000 LB2518 LBC2518 LBR2518 2.50.2 1.80.2 1.80.2 0.50.2 0.0980.008 0.0710.008 0.0710.008 0.0200.008 2000 LB3218 3.20.2 1.80.2 1.80.2 0.60.2 0.1280.008 0.0710.008 0.0710.008 0.0240.008 2000 LBC3225 3.20.2 2.50.2 2.50.2 0.60.3 0.1280.008 0.0980.008 0.0980.008 0.0240.012 A Surface Mounting Mounting and soldering conditions should be checked beforehand. Applicable soldering process to those products is reflow soldering only. Recommended Land Patterns W 1000 Unitmm inch AVAILABLE INDUCTANCE RANGE Type Range LB1608 LBMF1608 LB2012 LBC2012 LBR2012 LB2016 LBC2016 LB2518 LBC2518 LBR2518 LB3218 LBC3225 Imax.mA Rdc30 Imax.mA Rdc30 Imax.mA Rdc30 Imax.mA Rdc30 Imax.mA Rdc30 Imax.mA Rdc30 Imax.mA Rdc30 Imax.mA Rdc30 Imax.mA Rdc30 Imax.mA Rdc30 Imax.mA Rdc30 Imax.mA Rdc30 InductanceH 1 160 1H 0.17 230 1H 0.09 405 1H 0.15 620 1H 0.19 400 1H 0.07 490 1H 0.09 690 1H 70 10 665 1H 0.06 775 1H 0.08 960 1H 0.045 1075 1H 0.06 1100 1H 0.055 0.55 60 0.7 10H 80 0.36 120 35 0.7 2.5 47H 100 0.1 200 1.2 90 45 7.0 100H 150 0.36 155 0.5 245 0.82 165 50 40 4.5 100H 75 60 0.25 375 0.36 235 2.1 125 3.70 45 28.0 0.19 340 0.25 540 0.133 5.8 47H 4.0 100H 8.0 100H 15 24 1000H 1000 680H 80 1.89 140 100H 2.40 150 1.4 100H 39 27 1000H This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. 80 12 wound01_e-02 PART NUMBERS 1608 0603TYPE Ordering code LB 1608T1R0M LB 1608T2R2M LB 1608T4R7M LB 1608T8R2M LB 1608T100M Ordering code RoHS RoHS RoHS RoHS RoHS EHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Inductance H 1.0 2.2 4.7 8.2 10 Inductance Tolerance Inductance H 1.0 2.2 3.3 4.7 10 22 47 Inductance Tolerance 20% 20% 10% 20% Self-resonant frequency MHzmin. 100 80 45 32 32 DC Resistance 30 0.17 0.33 0.55 0.70 0.70 Rated current mAmax. 160 115 70 60 60 Measuring frequency MHz Self-resonant frequency MHzmin. 100 80 60 45 32 16 11 DC Resistance 30 0.09 0.17 0.22 0.24 0.36 1.0 2.5 Rated current mAmax. 230 160 130 110 80 50 35 Measuring frequency MHz Self-resonant frequency MHzmin. 100 80 55 45 38 32 32 28 16 11 10 8 DC Resistance 30 0.15 0.23 0.30 0.40 0.47 0.70 0.50 1.3 1.7 3.7 6.0 7.0 Rated current mAmax. 405 260 235 190 135 120 120 100 80 60 50 45 Measuring frequency MHz Self-resonant frequency MHzmin. 100 70 45 40 16 11 DC Resistance 30 0.19 0.33 0.50 1.2 3.7 5.8 Rated current mAmax. 620 430 295 200 130 90 Measuring frequency MHz Self-resonant frequency MHzmin. 100 80 45 32 16 11 8 DC Resistance 30 0.07 0.13 0.24 0.36 1.0 1.7 4.0 Rated current mAmax. 400 260 200 150 100 75 50 Measuring frequency MHz Self-resonant frequency MHzmin. 100 80 70 55 45 38 32 28 16 14 11 10 8 DC Resistance 30 0.09 0.11 0.13 0.20 0.25 0.35 0.50 0.70 1.0 1.7 2.4 3.0 4.5 Rated current mAmax. 490 380 375 285 225 200 155 130 105 85 70 55 40 Measuring frequency MHz 7.96 2.52 7.96 2.52 Please specify the Inductance tolerance code K or M 2012 0805TYPE Ordering code LB 2012T1R0M LB 2012T2R2M LB 2012T3R3M LB 2012T4R7M LB 2012T6R8M LB 2012T100 LB 2012T100R LB 2012T150 LB 2012T220 LB 2012T470 LB 2012T680 LB 2012T101 EHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Inductance H 1.0 2.2 3.3 4.7 6.8 10 10 15 22 47 68 100 Inductance Tolerance 20% 10% 20% 7.96 2.52 0.796 Please specify the Inductance tolerance code K or M Ordering code LB C2012T1R0M LB C2012T2R2M LB C2012T4R7M LB C2012T100 LB C2012T220 LB C2012T470 EHS RoHS RoHS RoHS RoHS RoHS RoHS Inductance H 1.0 2.2 4.7 10 22 47 Inductance Tolerance 20% 10% 20% STANDARD INDUCTORS INDUCTORS LBMF1608T1R0M LBMF1608T2R2M LBMF1608T3R3M LBMF1608T4R7M LBMF1608T100 LBMF1608T220 LBMF1608T470 EHS 7.96 2.52 Please specify the Inductance tolerance code K or M Ordering code LB R2012T1R0M LB R2012T2R2M LB R2012T4R7M LB R2012T100 LB R2012T220 LB R2012T470 LB R2012T101 EHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Inductance H 1.0 2.2 4.7 10 22 47 100 Inductance Tolerance 20% 10% 20% 7.96 2.52 0.796 Please specify the Inductance tolerance code K or M 2016 0806 TYPE Ordering code LB 2016T1R0M LB 2016T1R5M LB 2016T2R2M LB 2016T3R3M LB 2016T4R7M LB 2016T6R8M LB 2016T100 LB 2016T150 LB 2016T220 LB 2016T330 LB 2016T470 LB 2016T680 LB 2016T101 EHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Inductance H 1.0 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 68 100 Inductance Tolerance 20% 10% 20% 7.96 2.52 0.796 Please specify the Inductance tolerance code K or M This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. wound01_e-02 12 81 PART NUMBERS Ordering code LB C2016T1R0M LB C2016T1R5M LB C2016T2R2M LB C2016T3R3M LB C2016T4R7M LB C2016T6R8M LB C2016T100 LB C2016T150 LB C2016T220 LB C2016T330 LB C2016T470 LB C2016T680 LB C2016T101 EHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Inductance H 1.0 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 68 100 Inductance Tolerance 20% 10% 20% Self-resonant frequency MHzmin. 100 80 70 55 45 38 32 28 16 14 11 10 8 DC Resistance 30 0.10 0.15 0.20 0.27 0.37 0.59 0.82 1.2 1.8 2.8 4.3 7.0 8.0 Rated current mAmax. 690 600 520 410 355 290 245 200 165 135 110 95 75 Measuring frequency MHz Self-resonant frequency MHzmin. 100 80 68 54 46 46 38 30 23 19 15 12 9.5 9.0 7.0 5.5 4.5 3.5 3.0 2.4 DC Resistance 30 0.06 0.07 0.09 0.11 0.13 0.10 0.15 0.25 0.32 0.50 0.70 0.95 1.5 2.1 3.2 4.5 7.0 10 17 24 Rated current mAmax. 665 405 340 280 240 235 195 165 145 115 95 85 70 60 45 40 30 25 20 15 Measuring frequency MHz Self-resonant frequency MHzmin. 100 100 80 68 54 41 38 30 23 19 15 12 9.5 9.0 7.0 5.5 4.5 3.5 3.0 DC Resistance 30 0.080 0.065 0.11 0.13 0.16 0.20 0.30 0.36 0.65 0.77 1.5 1.9 2.8 3.7 6.1 8.4 12.3 22 28 Rated current mAmax. 775 890 730 630 560 510 420 375 285 250 185 165 140 125 95 80 65 50 45 Measuring frequency MHz Self-resonant frequency MHzmin. 100 68 45 30 19 11 9 DC Resistance 30 0.045 0.07 0.10 0.19 0.44 0.84 1.89 Rated current mAmax. 960 480 345 235 175 120 80 Measuring frequency MHz 7.96 2.52 0.796 Please specify the Inductance tolerance code K or M 2518 1007TYPE Ordering code LB 2518T1R0M LB 2518T1R5M LB 2518T2R2M LB 2518T3R3M LB 2518T4R7M LB 2518T4R7MR LB 2518T6R8M LB 2518T100 LB 2518T150 LB 2518T220 LB 2518T330 LB 2518T470 LB 2518T680 LB 2518T101 LB 2518T151 LB 2518T221 LB 2518T331 LB 2518T471 LB 2518T681 LB 2518T102 EHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Inductance H 1.0 1.5 2.2 3.3 4.7 4.7 6.8 10 15 22 33 47 68 100 150 220 330 470 680 1000 Inductance Tolerance 20% 10% 20% 7.96 2.52 0.796 0.252 Please specify the Inductance tolerance code K or M Ordering code LB C2518T1R0M LB C2518T1R0MR LB C2518T1R5M LB C2518T2R2M LB C2518T3R3M LB C2518T4R7M LB C2518T6R8M LB C2518T100 LB C2518T150 LB C2518T220 LB C2518T330 LB C2518T470 LB C2518T680 LB C2518T101 LB C2518T151 LB C2518T221 LB C2518T331 LB C2518T471 LB C2518T681 EHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Inductance H 1.0 1.0 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 68 100 150 220 330 470 680 Inductance Tolerance 20% 10% 20% 7.96 2.52 0.796 Please specify the Inductance tolerance code K or M Ordering code LB R2518T1R0M LB R2518T2R2M LB R2518T4R7M LB R2518T100 LB R2518T220 LB R2518T470 LB R2518T101 EHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Inductance H 1.0 2.2 4.7 10 22 47 100 Inductance Tolerance 20% 10% 20% 7.96 2.52 0.796 Please specify the Inductance tolerance code K or M This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. 82 12 wound01_e-02 PART NUMBERS 3218 1297TYPE Ordering code RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Inductance H 1.0 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 68 100 150 220 330 470 680 1000 Inductance Tolerance 20% 10% 20% Self-resonant frequency MHzmin. 100 80 68 54 41 40 30 25 19 15 12 11 8 7 5 4 3.5 3.0 2.4 DC Resistance 30 0.06 0.07 0.09 0.11 0.13 0.17 0.25 0.32 0.49 0.75 0.92 1.49 2.4 3.2 5.4 7.0 14 17 27 Rated current mAmax. 1075 860 775 560 550 380 340 300 255 215 205 145 140 105 80 65 54 45 39 Measuring frequency MHz Self-resonant frequency MHzmin. 250 220 190 160 70 50 23 20 17 13 10 8 6 DC Resistance 30 0.055 0.060 0.080 0.095 0.100 0.120 0.133 0.195 0.27 0.41 0.67 1.0 1.4 Rated current mAmax. 1100 1000 930 820 680 620 540 420 330 300 220 190 150 Measuring frequency MHz 7.96 2.52 0.796 0.252 Please specify the Inductance tolerance code K or M 3225 1210TYPE Ordering code LB C3225T1R0MR LB C3225T1R5MR LB C3225T2R2MR LB C3225T3R3MR LB C3225T4R7MR LB C3225T6R8MR LB C3225T100R LB C3225T150R LB C3225T220R LB C3225T330R LB C3225T470R LB C3225T680R LB C3225T101R EHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Inductance H 1.0 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 68 100 Inductance Tolerance 20% 10% 20% 0.1 STANDARD INDUCTORS INDUCTORS LB 3218T1R0M LB 3218T1R5M LB 3218T2R2M LB 3218T3R3M LB 3218T4R7M LB 3218T6R8M LB 3218T100 LB 3218T150 LB 3218T220 LB 3218T330 LB 3218T470 LB 3218T680 LB 3218T101 LB 3218T151 LB 3218T221 LB 3218T331 LB 3218T471 LB 3218T681 LB 3218T102 EHS Please specify the Inductance tolerance code K or M This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. wound01_e-02 12 83 ELECTRICAL CHARACTERISTICS DC Bias characteristicsMeasured by HP4285A42841A LBMF1608 LB2012 10 10 100 DC Bias mA 1 0.1 1000 1 10 100 DC Bias mA LBR2012 10 101 100 100 1000 DC Bias mA 101 100 100 10 1R0M 1 0.1 10000 100 10 1 10 100 DC Bias mA LBC2016 Inductance H Inductance H Inductance H 1 1R0M 1 1000 LB2518 1000 1000 10 1R0M 1 LB2016 1000 100 100 10 0.1 1000 101 100 1000 101 100 100 10 1R0M 1 Inductance H 1 1R0M Inductance H 1R0M 1 0.1 Inductance H Inductance H 100M 100 470 4R7M 10 LBC2012 1000 100 Inductance H LB1608 100 101 100 100 10 1R0M 1 1R0M 10 100 DC Bias mA 0.1 1000 1 10 101 100 100 10 1R0M 1 1 10 1 10 100 1000 DC Bias mA 10000 0.1 10000 101 100 10 1R0M 1 1 10 1 10 100 1000 DC Bias mA 10000 100 10000 101 101 100 100 10 1R0M 1 0.1 100 1000 DC Bias mA 3225 1000 100 0.1 100 1000 DC Bias mA LB3218 1000 Inductance H Inductance H 0.1 10000 LBR2518 LBC2518 1000 0.1 100 1000 DC Bias mA 1 10 100 1000 DC Bias mA 10000 Inductance H 1 Inductance H 1 100 10 1R0MR 1 0.1 1 10 100 1000 DC Bias mA 10000 This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. 84 12 wound01_e-02 STANDARD INDUCTORS INDUCTORS This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. wound01_e-02 12 85 PACKAGING Minimum Quantity Leader and Blank Portion Type LBC3225/CBC3225 LB3218 LBR2518/LBC2518/LB251 /CB2518/CBC2518/LEM2520 LBM2016/LBC2016/ LB2016/CB2016/CBC2016 LB2012/LBC2012/LBR202 /CB2012/CBC2012 CBL2012 LB1608 LBMF1608/CBMF1608 Standard Quantitypcs Papar Tape Embossed Tape 1000 2000 2000 2000 3000 4000 4000 3000 (10 pitches or more) (10 pitches or more) 150mm or more (5.9 inches or more) Reel Size 0.039 60 1 ) -02.36 -0 Embossed tape 180 0 7.09 0 -3 -0.118 ) 2.5 max 0.098 Tape material 10.01.5 (0.3940.059) Top Tape Strength The top tape requires a peel-off force 0.2 to 0.7N in the direction of the arrow as illustrated below. Pull direction Taping Dimensions Embossed Tape0.315 inches wide Card board carrier tape0.315 inches wide Chip cavity Type LBM 2016 LEM 2520 LBC3225/ CBC3225 LB3218 A Insertion pitch B F Tape thickness T K 2.10.1 4.00.1 0.30.05 1.9max. 1.750.1 0.0690.0040.0830.0040.1570.0040.0120.002 0.075max. 2.70.1 4.00.1 0.30.05 2.10.1 2.30.1 0.0910.004 0.1060.0040.1570.0040.0120.0020.0830.004 2.80.1 3.50.1 4.00.1 0.30.05 4.0max. 0.1100.0040.1380.0040.1570.0040.0120.002 0.157max. 3.50.1 4.00.1 0.30.05 2.2max. 2.10.1 0.0830.004 0.1380.0040.1570.0040.0120.002 0.087max. LB2518 / CB2518 2.150.1 2.70.1 4.00.1 0.30.05 2.2max. LBC2518 / CBC2518 0.0850.004 0.1060.0040.1570.0040.0120.002 0.087max. LBR2518 LB2016/ CB2016 1.750.1 2.10.1 4.00.1 0.30.05 1.9max. LBC2016 / CBC2016 0.0690.0040.0830.0040.1570.0040.0120.002 0.075max. LB2012 / CB2012 1.450.1 2.250.1 4.00.1 0.250.05 1.45max. LBC2012 / CBC2012 0.0570.004 0.0890.004 0.1570.0040.0100.002 0.057max. LBR2012 2.30.1 4.00.1 1.1max. 1.1max. 1.550.1 CBL2012 0.0610.004 0.0910.004 0.1570.004 0.043max. 0.043max. 1.80.1 4.00.1 1.1max. 1.1max. 1.00.1 LB1608 0.0390.004 0.0710.004 0.1570.004 0.043max. 0.043max. 1.10.1 1.90.1 4.00.1 0.250.05 1.2max. LBMF1608 / CBMF1608 0.0430.004 0.0750.004 0.1570.0040.0100.002 0.047max. Unitmm inch This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. wound0103_reli_e-01 12 wound0103_reli-PRP1 RELIABILITY DATA 1.Operating temperature Range LB, LBC, LBR, LBMF Series CB, CBC, CBL, CBMF Series LBM Series LEM Series Including self-generated heat 40105 4085 2.Storage LB, LBC, LBR, LBMF Series CB, CBC, CBL, CBMF Series LBM, LEM Series Test Methods and Remarks Please refer the term of "7. storage conditions" in precautions. 4085 3.Rated Current LB, LBC, LBR, LBMF Series CB, CBC, CBL, CBMF Series Within the specified tolerance LBM, LEM Series Test Methods and Remarks LEM Series The maximum DC value having inductance decrease within 10 and temperature increase within 20 by the application of DC bias. 4.Inductance LB, LBC, LBR, LBMF Series CB, CBC, CBL, CBMF Series LBM, LEM Series Test Methods and Remarks LEM Series Within the specified tolerance LBLBCLBRCBCBCCBLLBMFCBMFLBM Series Measuring equipmentLCR Meter HP4285A42851A or its equivalent Measuring frequencySpecified frequency Measuring equipmentLCR Mater HP4285A or its equivalent 5.Q LB, LBC, LBR, LBMF Series CB, CBC, CBL, CBMF Series LBM, LEM Series Test Methods and Remarks LEM Series Measuring equipmentLCR MeterHP4285A42851A or its equivalent Measuring frequencySpecified frequency LBM Series Measuring equipmentLCR Mater HP4285A or its equivalent 6.DC Resisitance LB, LBC, LBR, LBMF Series CB, CBC, CBL, CBMF Series LBM, LEM Series Test Methods and Remarks Measuring equipmentDC Ohmmeter HIOKI 3227 or its equivalent Within the specified tolerance 7.Self-Resonant Frequency LB, LBC, LBR, LBMF Series CB, CBC, CBL, CBMF Series LBM, LEM Series Test Methods and Remarks Measuring equipmentImpedance analyzer HP4291A or its equivalent 8.Temperature Characteristic LBM2016 LEM2520 CB2012 CBL2012 LB1608 LB2012 LBR2012 CB2016 LB2518 LBR2518 CB2518 LBC3225 CBC2016 LBC2518 LBMF1608 CBMF1608 LBC2016 CBC2518 LB3218 LBC2012 CBC2012 Test Methods and Remarks Change of maximum inductance deviation in step 1-5 LB, CB Series Step 1 2 LEM2520 Within the specified tolerance Within the specified tolerance Inductance change:Within5 LB2016 CBC3225 Inductance change:Within20 Inductance change:Within25 Inductance change:Within35 Temperture 20 40 3 4 20Reference temperature 85Maximum operating temperature 5 20 Step Temperture 1 20 2 25 3 4 20Reference temperature 85Maximum operating temperature 5 20 9.Rasistance to Flexure of Substrate LB, LBC, LBR, LBMF Series CB, CBC, CBL, CBMF Series LBM, LEM Series Test Methods and Remarks Warp 2mm LBLBCLBRCBCBCCBLLBMLBMFCBMF Series 3mm LEM2520 Test substrate: Board according to JIS C0051 No damage. Pressing jig LEM25201.6mm LBLBMF CBMF1608 0.8mm Others1.0mm Board This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. wound0103_reli-PRP2 12 wound0103_reli_e-01 RELIABILITY DATA 10.Body Strength LB, LBC, LBR, LBMF Series CB, CBC, CBL, CBMF Series LBM, LEM Series Test Methods and Remarks LBLBCLBRCBCBCCBLLBMLEM2520 LB1608LBMF1608CBMF1608 No damage. Applied force10N Duration10sec. Applied force5N Duration10sec. 11.Adhesion of terminal electrode LB, LBC, LBR, LBMF Series CB, CBC, CBL, CBMF Series LBM, LEM Series Test Methods and Remarks LBLBCLBRCBCBCCBLLBMLBMFCBMFLEM2520 LB1608CBMF1608LBMF1608 No abnormality. Applied force10N to X and Y directions Duration5 sec. Test substratePrinted board Applied force5N to X and Y directions Duration5 sec. Test substratePrinted board 12.Resistance to vibration LB, LBC, LBR, LBMF Series Inductance change:Within10 CB, CBC, CBL, CBMF Series LBM, LEM Series Inductance change:Within5 Test Methods and Remarks LEMLBLBCLBRCBCBCCBLLBMLBMFCBMFAccording to JIS C5102 clause 8.2. Vibration typeA Directions2 hrs each in X, Y and Z directions. Total6 hrs Frequency range10 to 55 to 10 Hz1min. Amplitude1.5mm Mounting methodSoldering onto printed board RecoveryAt least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. LEMRecovery At least 1 hr of recovery under the standard condition after the test, followed by the measurement within 2 hrs. 13.Drop test LB, LBC, LBR, LBMF Series CB, CBC, CBL, CBMF Series LBM Series LEM Series Inductance change:Within5 Test Methods and Remarks LEM Acceleration980m/sec2 Duration6msec Number of times6 sides x 3 times Mounting methodSoldering onto printed board RecoveryAt least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. LEMRecovery At least 1 hr of recovery under the standard condition after the test, followed by the measurement within 2 hrs. 14.Solderability LB, LBC, LBR, LBMF Series CB, CBC, CBL, CBMF Series LBM, LEM Series Test Methods and Remarks LEM No significant abnormality in appearance. No significant abnormality in appearance. No significant abnormality in appearance. At least 90 of surface of terminal electrode is covered by new Solder temperature2305 Duration50.5sec. FluxMethanol solution with 25 of colophony LBLBCLBRCBCBCCBLLBMLBMFCBMF Solder temperature2455 Duration50.5sec FluxMethanol solution with 25 of colophony This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. wound0103_reli_e-01 12 wound0103_reli-PRP3 RELIABILITY DATA 15.Resistance to soldering LB, LBC, LBR, LBMF Series Inductance change:Within10 CB, CBC, CBL, CBMF Series LEM Series Inductance change:Within5 LEM2520 No significant abnormality in appearance. Test Methods and Remarks LEM Reflow condition 3 times of reflow over at 2205 for 40sec. MAX, With Peak temperature at 2405 for 5 sec. MAX.Refer to a Profile of chart below. Flow condition Solder temperature2605 Duration101sec. Once LBLBCLBRCBCBCCBLLBMLBMFCBMF 3 times of reflow oven at 230 MIN for 40sec. with peak temperature at 260 for 5sec. 16.Resisitance to solvent LB, LBC, LBR, LBMF Series CB, CBC, CBL, CBMF Series LBM, LEM Series Test Methods and Remarks Solvent temperatureRoom temperature Type of solventIsopropyl alcohol Cleaning conditions90s. Immersion and cleaning. No significant abnormality in appearance 17.Thermal shock LB, LBC, LBR, LBMF Series CB, CBC, CBL, CBMF Series LBM Series Inductance change:Within10 Inductance change :Within10 Q R124R730 min. 5R633025 min. 39082020 min. 10115 min. LEM Series Test Methods and Remarks LEM : Conditions for 1cycle No significant abnormality in appearance. Step 1 2 Temperature 40 85 Duration min 30 30 Number of cycle100 cycle RecoveryAt least 1 hr of recovery under the standard condition after the test, followed by the measurement within 2 hrs. LBLBCLBRCBCBCCBLLBMLBMFCBMF 4085, maintain times 30min. ,100 cycle RecoveryAt least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. 18.Damp heat life test LB, LBC, LBR, LBMF Series CB, CBC, CBL, CBMF Series LBM Series LEM Series Inductance change:Within10 No significant abnormality in appearance. Inductance change :Within10 Q R124R730 min. 5R633025 min. 39082020 min. 10115 min. Test Methods and Remarks Temperature602 Humidity9095RH Duration1000 hrs RecoveryAt least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. LEMRecovery At least 1 hr of recovery under the standard condition after the test, followed by the measurement within 2 hrs. 19.Loading under damp heat life test LB, LBC, LBR, LBMF Series CB, CBC, CBL, CBMF Series LBM Series LEM Series Inductance change:Within10 No significant abnormality in appearance. Inductance change :Within10 Q R124R730 min. 5R633025 min. 39082020 min. 10115 min. Test Methods and Remarks Temperature602 Humidity9095RH Duration1000 hrs Applied currentRated current RecoveryAt least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. LEMRecovery At least 1 hr of recovery under the standard condition after the test, followed by the measurement within 2 hrs. This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. wound0103_reli-PRP4 12 wound0103_reli_e-01 RELIABILITY DATA 20.High temperature life test LB, LBC, LBR, LBMF Series CB, CBC, CBL, CBMF Series LBM Series LEM Series Inductance change:Within10 No significant abnormality in appearance. Inductance change :Within10 Q R124R730 min. 5R633025 min. 39082020 min. 10115 min. Test Methods and Remarks Temperature852 Duration1000 hrs RecoveryAt least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. LEMRecovery At least 1 hr of recovery under the standard condition after the test, followed by the measurement within 2 hrs. 21.Loading at high temperature life test LB, LBC, LBR, LBMF Series Inductance change:Within10 CB, CBC, CBL, CBMF Series LBM, LEM Series Test Methods and Remarks Temperature852 Duration1000 hrs Applied currentRated current RecoveryAt least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. 22.Low temperature life test LB, LBC, LBR, LBMF Series CB, CBC, CBL, CBMF Series LBM Series LEM Series Inductance change:Within10 No significant abnormality in appearance. No significant abnormality in appearance. Inductance change :Within10 Q R124R730 min. 5R633025 min. 39082020 min. 10115 min. Test Methods and Remarks Temperature402 Duration1000 hrs RecoveryAt least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. LEMRecovery At least 1 hr of recovery under the standard condition after the test, followed by the measurement within 2 hrs. 23.Standard condition LB, LBC, LBR, LBMF Series CB, CBC, CBL, CBMF Series LBM, LEM Series Standard test conditions Unless specified, Ambient temperature is 2015 and the Relative humidity is 65 20. If there is any doubt about the test results, further measurement shall be had within the following limits: Ambient Temperature: 202 Relative humidity: 655 Inductance value is based on our standard measurement systems. This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. wound0103_reli_e-01 12 wound0103_reli-PRP5 PRECAUTIONS LEM TypeLB TypeCB Type 1Circuit Design Operating environment 1The products described in this specification are intended for use in general electronic equipment,(office supply equipment, telecommunications systems, measuring equipment, and household equipment). They are not intended for use in mission-critical equipment or systems requiring special quality and high Precautions reliability (traffic systems, safety equipment, aerospace systems, nuclear control systems and medical equipment including life-support systems,) where product failure might result in loss of life, injury or damage. For such uses, contact TAIYO YUDEN Sales Department in advance. 2PCB Design Land pattern design Precautions 1Please contact any of our offices for a land pattern, and refer to a recommended land pattern of a right figure or specifications. PRECAUTIONS Technical Recommended Land Patterns considerSurface Mounting ations Mounting and soldering conditions should be checked beforehand. Applicable soldering process to those products is reflow soldering only. 3Considerations for automatic placement Adjustment of mounting machine Precautions 1. Excessive impact load should not be imposed on the products when mounting onto the PC boards. 2. Mounting and soldering conditions should be checked beforehand. Technical consider- 1. When installing products, care should be taken not to apply distortion stress as it may deform the products. ations 4Soldering Wave solderingLEM Type only 1For wave soldering,please apply conditions meeting the range of the specifed conditions in our catalog or the relevant specifications. Reflow solderingLB and CB Types 1For reflow soldering with either leaded or lead-free solder,the profile specified in "point for controlling" is recommended. Precautions Reflow solderingLEM 1For reflow soldering, please apply conditions meeting the range of the specified conditions in our catalog or the relevant specifications. Recommended conditions for using a soldering iron 1Put the soldering iron on the land-pattern. Soldering iron's temperature - Below 350 Duration-3 seconds or less. The soldering iron shoud not come in contact with inductor directly. Wave solderingLEM Type only 1Components can be damaged by excessive heat where soldering conditions exceed the specified range. Reflow solderingLB and CB Types 1Reflow profile 300 Peak Temp: 2600/5 5 sec Max 250 Technical considerations 200 180 230 Minn Pre-heat zone 150 150 100 9030 sec 3010 sec 50 0 Recommended conditions for using a soldering iron 1Components can be damaged by excessive heat where soldering conditions exceed the specified range. 5Cleaning Precautions Technical considerations Cleaning conditions Washing by supersonic waves shall be avoided. Cleaning conditions If washed by supersonic waves, the products might be broken. 6Handling Handling 1There is a case that a characteristic varies with magnetic influence. Breakaway PC boardssplitting along perforations Precautions 1Planning pattern configurations and the position of products should be carefully performed to minimize stress. Mechanical considerations 1There is a case to be damaged by a mechanical shock. Handling 1Keep the inductors away from all magnets and magnetic objects. Technical Breakaway PC boardssplitting along perforations 1When splitting the PC board after mounting inductors, care should be taken not to give any stresses of deflection or twisting to the board. consider2Board separation should not be done manually, but by using the appropriate devices. ations Mechanical considerations 1Please do not give the inductors any excessive mechanical shocks. 7Storage conditions Storage Precautions 1Under a high temperature and humidity environment, problems such as reduced solderability caused by oxidation of terminal electrodes and deterioration of taping/packaging materials may take place. Storage 1To maintain the solderability of terminal electrodes and to keep the packing material in good condition, temperature and humidity in the storage area should be controlled. Recommended conditions Technical Ambient temperature040 HumidityBelow 70% RH considerThe ambient temperature must be kept below 30 even under ideal storage conditions, solderability of products electrodes may decrease as time passes. For ations this reason, LE type inductors should be used within one year from the time of delivery. LB typeShould be used within 6 months from the time of delivery. LE typeIn case of storage over 6 months, solderability shall be checked before actual usage. This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. wound0103_reli-PRP6 12 wound0103_reli_e-01