NCV7349 High Speed Low Power CAN Transceiver Description The NCV7349 CAN transceiver is the interface between a controller area network (CAN) protocol controller and the physical bus. The transceiver provides differential transmit capability to the bus and differential receive capability to the CAN controller. The NCV7349 is a new addition to the CAN high-speed transceiver family complementing NCV734x CAN family and previous generations of CAN transceivers such as AMIS42665, AMIS3066x, etc. Due to the wide common-mode voltage range of the receiver inputs and other design features, the NCV7349 is able to reach outstanding levels of electromagnetic susceptibility (EMS). Similarly, very low electromagnetic emission (EME) is achieved by the excellent matching of the output signals. www.onsemi.com MARKING DIAGRAM 8 8 SOIC-8 CASE 751AZ Features * * (Note: Microdot may be in either location) PIN ASSIGNMENT 8 1 TxD STB 2 GND 3 VCC NV7349-0 ALYWG G * * * * * * * * * 1 NV7349-x = Specific Device Code x = 0 or 3 A = Assembly Location L = Wafer Lot Y = Year W = Work Week G = Pb-Free Package * Compatible with the ISO 11898-5 Standard * High Speed (up to 1 Mbps) * VIO Pin on NCV7349-3 Version Allowing Direct Interfacing with 3 V to 5 V Microcontrollers Very Low Current Standby Mode with Wake-up via the Bus Low Electromagnetic Emission (EME) and Extremely High Electromagnetic Immunity Very Low EME without Common-mode (CM) Choke No Disturbance of the Bus Lines with an Un-powered Node Transmit Data (TxD) Dominant Time-out Function Under All Supply Conditions the Chip Behaves Predictably Very High ESD Robustness of Bus Pins, >10 kV System ESD Pulses Thermal Protection Bus Pins Short Circuit Proof to Supply Voltage and Ground Bus Pins Protected Against Transients in an Automotive These are Pb-Free Devices NV7349-x ALYW G G 1 7 CANH 6 CANL 5 4 NC RxD NCV7349D10R2G (Top View) Quality * NCV Prefix for Automotive and Other Applications Requiring 1 8 2 7 TxD STB GND Typical Applications 3 * Automotive * Industrial Networks VCC NV7349-3 ALYWG G Unique Site and Control Change Requirements; AEC-Q100 Qualified and PPAP Capable CANH 6 CANL 5 4 VIO RxD NCV7349D13R2G (Top View) ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 10 of this data sheet. (c) Semiconductor Components Industries, LLC, 2014 December, 2014 - Rev. 1 1 Publication Order Number: NCV7349/D NCV7349 Table 1. KEY TECHNICAL CHARACTERISTICS AND OPERATING RANGES Symbol Parameter Conditions VCC Power supply voltage (Note 1) VUV Undervoltage detection voltage on pin Vcc Min Max Unit 4.75 (4.5) 5.25 (5.5) V 2 4 V VCANH DC voltage at pin CANH 0 < VCC < 5.5 V; no time limit -50 +50 V VCANL DC voltage at pin CANL 0 < VCC < 5.5 V; no time limit -50 +50 V DC voltage at pin CANH and CANL during load dump condition 0 < VCC < 5.5 V, less than one second - +58 V Electrostatic discharge voltage IEC 61000-4-2 at pins CANH and CANL -15 15 kV Differential bus output voltage in dominant state 45 W < RLT < 65 W 1.5 3 V Input common-mode range for comparator Guaranteed differential receiver threshold and leakage current -35 +35 V - 15 pF - 245 ns - 250 ns -40 150 C VCANH,Lmax VESD VO(dif)(bus_dom) CM-range Cload Load capacitance on IC outputs tpd0 Propagation delay (NCV7349-0 version) See Figure 7 tpd3 Propagation delay (NCV7349-3 version) See Figure 7 TJ Junction temperature Functional operation above the stresses listed in the Recommended Operating Ranges is not implied. Extended exposure to stresses beyond the Recommended Operating Ranges limits may affect device reliability. 1. In the range of 4.5 V to 4.75 V and from 5.25 V to 5.5 V the chip is fully functional; some parameters may be outside of the specification. BLOCK DIAGRAM VCC VIO (*) 3 5 VIO NCV7349 7 Thermal shutdown TxD CANH 1 Timer VIO STB RxD GND 8 4 Mode & Wake-up control 6 Driver control Wake-up Filter COMP 2 COMP *On NCV7349-0 version pin 5 is not connected. VIO supply is provided by VCC. Figure 1. Block Diagram www.onsemi.com 2 CANL NCV7349 TYPICAL APPLICATION VBAT IN 5 V - reg OUT VCC VCC NC 5 STB TxD 1 RxD 7 NCV7349-0 Micro- controller 8 3 RLT = 60 W CANH CAN BUS 4 6 CANL RLT = 60 W 2 GND GND Figure 2. Application Diagram, NCV7349-0 VBAT IN IN 5 V - reg OUT OUT 3 V - reg VIO VCC 5 STB TxD RxD 1 4 7 NCV7349-3 Micro- controller 8 3 RLT = 60 W CANH CAN BUS 6 CANL 2 GND RLT = 60 W GND Figure 3. Application Diagram, NCV7349-3 Table 2. PIN FUNCTION DESCRIPTION Pin Name Description 1 TxD Transmit data input; low input U Driving dominant on bus; internal pull-up current 2 GND Ground 3 VCC Supply voltage 4 RxD Receive data output; bus in dominant U low output 5 5 NC VIO Not connected. On NCV7349-0 only. Input / Output pins supply voltage. On NCV7349-3 only 6 CANL Low-level CAN bus line (low in dominant mode) 7 CANH High-level CAN bus line (high in dominant mode) 8 STB Standby mode control input; internal pull-up current www.onsemi.com 3 NCV7349 FUNCTIONAL DESCRIPTION Standby Mode NCV7349 has two versions which differ from each other only by function of pin 5. NCV7349-0: Pin 5 is not connected. (see Figure 2) NCV7349-3: Pin 5 is VIO pin, which is supply pin for transceiver digital inputs/output (supplying pins TxD, RxD, STB) The VIO pin should be connected to microcontroller supply pin. By using VIO supply pin shared with microcontroller the I/O levels between microcontroller and transceiver are properly adjusted. This adjustment allows in applications with microcontroller supply down to 3 V to easy communicate with the transceiver. (See Figure 3) In standby mode both the transmitter and receiver are disabled and a very low-power differential receiver monitors the bus lines for CAN bus activity. The bus lines are terminated to ground and supply current is reduced to a minimum, typically 10 mA. When a wake-up request is detected by the low-power differential receiver, the signal is first filtered and then verified as a valid wake signal after a time period of twake, the RxD pin is driven low by the transceiver to inform the controller of the wake-up request. VIO Supply pin The VIO pin available only on NCV7349-3 version should be connected to microcontroller supply pin. By using VIO supply pin shared with microcontroller the I/O levels between microcontroller and transceiver are properly adjusted. See Figure 3. Pin VIO on NCV7349-3 does not provide the internal supply voltage for low-power differential receiver of the transceiver. Detection of wake-up request is not possible when there is no supply voltage on pin VCC. Operating Modes NCV7349 provides two modes of operation as illustrated in Table 3. These modes are selectable through pin STB. Table 3. OPERATING MODES Pin RxD Pin STB Mode Low Normal Bus dominant Bus recessive High Standby Wake-up request detected No wake-up request detected Low High Wake-up When a valid wake-up (dominant state longer than twake) is received during the standby mode the RxD pin is driven low. The wake-up detection is not latched: RxD returns to High state after tdwakedr when the bus signal is released back to recessive - see Figure 4. Normal Mode In the normal mode, the transceiver is able to communicate via the bus lines. The signals are transmitted and received to the CAN controller via the pins TxD and RxD. The slopes on the bus lines outputs are optimized to give low EME. >tWake <tWake CANH CANL STB RxD1 tdwakerd tdwakedr tWake(RxD) normal standby time Figure 4. NCV7349 Wake-up Behavior www.onsemi.com 4 NCV7349 Over-temperature Detection Fail Safe Features A thermal protection circuit protects the IC from damage by switching off the transmitter if the junction temperature exceeds a value of approximately 170C. Because the transmitter dissipates most of the power, the power dissipation and temperature of the IC is reduced. All other IC functions continue to operate. The transmitter off-state resets when the temperature decreases below the shutdown threshold and pin TxD goes high. The thermal protection circuit is particularly needed when a bus line short circuits. A current-limiting circuit protects the transmitter output stage from damage caused by accidental short circuit to either positive or negative supply voltage, although power dissipation increases during this fault condition. Undervoltage on VCC pin prevents the chip sending data on the bus when there is not enough VCC supply voltage. After supply is recovered TxD pin must be first released to high to allow sending dominant bits again. Recovery time from undervoltage detection is equal to td(stb-nm) time. VIO supply dropping below VUVDVIO undervoltage detection level will cause the transmitter to disengage from the bus (no bus loading) until the VIO voltage recovers (NCV7349-3 version only). The pins CANH and CANL are protected from automotive electrical transients (according to ISO 7637; see Figure 7). Pins TxD and STB are pulled high internally should the input become disconnected. Pins TxD, STB and RxD will be floating, preventing reverse supply should the VIO supply be removed. TxD Dominant Time-out Function A TxD dominant time-out timer circuit prevents the bus lines being driven to a permanent dominant state (blocking all network communication) if pin TxD is forced permanently low by a hardware and/or software application failure. The timer is triggered by a negative edge on pin TxD. If the duration of the low-level on pin TxD exceeds the internal timer value tdom(TxD), the transmitter is disabled, driving the bus into a recessive state. The timer is reset by a positive edge on pin TxD. This TxD dominant time-out time (tdom(TxD)) defines the minimum possible bit rate to 15 kbps. www.onsemi.com 5 NCV7349 ELECTRICAL CHARACTERISTICS Definitions All voltages are referenced to GND (pin 2). Positive currents flow into the IC. Sinking current means the current is flowing into the pin; sourcing current means the current is flowing out of the pin. ABSOLUTE MAXIMUM RATINGS Table 4. ABSOLUTE MAXIMUM RATINGS Symbol Parameter VSUP Supply voltage VCC, VIO VCANH DC voltage at pin CANH VCANL DC voltage at pin CANL Conditions Min. Max. Unit -0.3 +6 V 0 < VCC < 5.5 V; no time limit -50 +50 V 0 < VCC < 5.5 V; no time limit -50 +50 V -0.3 6 V VIO DC voltage at pin TxD, RxD, STB Vesd Electrostatic discharge voltage at all pins (Note 2) (Note 3) -6 500 6 500 kV V Electrostatic discharge voltage at CANH and CANL pins (Note 4) -10 10 kV Transient voltage (Note 5) -150 100 V Static latch-up at all pins (Note 6) 150 mA Vschaff Latch-up Tstg Storage temperature -55 +150 C TA Ambient temperature -40 +125 C TJ Maximum junction temperature -40 +170 C Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected. 2. Standardized human body model electrostatic discharge (ESD) pulses in accordance to EIA-JESD22. Equivalent to discharging a 100 pF capacitor through a 1.5 kW resistor. 3. Standardized charged device model ESD pulses when tested according to ESD-STM5.3.1-1999. 4. System human body model electrostatic discharge (ESD) pulses. Equivalent to discharging a 150 pF capacitor through a 330 W resistor referenced to GND. 5. Pulses 1, 2a, 3a and 3b according to ISO 7637 part 3. Indicative values based on structural similarity to NCV7340 where results were verified by external test house. 6. Static latch-up immunity: Static latch-up protection level when tested according to EIA/JESD78. Table 5. THERMAL CHARACTERISTICS Symbol Conditions Value Unit RqJA_1 Thermal Resistance Junction-to-Air, 1S0P PCB (Note 7) Parameter Free air 125 K/W RqJA_2 Thermal Resistance Junction-to-Air, 2S2P PCB (Note 8) Free air 75 K/W 7. Test board according to EIA/JEDEC Standard JESD51-3, signal layer with 10% trace coverage 8. Test board according to EIA/JEDEC Standard JESD51-7, signal layers with 10% trace coverage www.onsemi.com 6 NCV7349 ELECTRICAL CHARACTERISTICS Table 6. CHARACTERISTICS (VCC = 4.75 V to 5.25 V; VIO = 2.8 V to 5.5 V (NCV7349-3 only); TJ = -40 to +150C; RLT = 60 W unless specified otherwise. On chip versions without VIO pin, reference voltage for all digital inputs and outputs is VCC instead of VIO.) Symbol Parameter Conditions Min Typ Max Unit SUPPLY (Pin VCC) ICC Supply current Dominant; VTxD = 0 V Recessive; VTxD = VIO - 48 6 75 10 mA ICCS Supply current in standby mode TJ 100C, (Note 9) - 10 15 mA 2 3 4 V 2.8 - 5.5 V VUVDVCC Undervoltage detection voltage on VCC pin SUPPLY (pin VIO) on NCV7349-3 Version Only VIO Supply voltage on pin VIO IIOS Supply current on pin VIO in standby mode Standby mode - 1 - mA IIONM Supply current on pin VIO in normal mode Dominant; VTxD = 0 V Recessive; VTxD = VIO For VIO VCC - - 1 0.2 mA 1.3 - 2.7 V V VUVDVIO Undervoltage detection voltage on VIO pin TRANSMITTER DATA INPUT (Pin TxD) VIH High-level input voltage Output recessive 2.0 - VIO VIL Low-level input voltage Output dominant -0.3 - +0.8 V IIH High-level input current VTxD = VIO -5 0 +5 mA IIL Low-level input current VTxD = 0 V -350 -200 - mA Ci Input capacitance (Note 9) - 5 10 pF V TRANSMITTER MODE SELECT (Pin STB) VIH High-level input voltage Standby mode 2.0 - VIO VIL Low-level input voltage Normal mode -0.3 - +0.8 V IIH High-level input current VSTB = VIO -5 0 +5 mA IIL0 Low-level input current, NCV7349-0 VSTB = 0 V -10 -4 -1 mA IIL3 Low-level input current, NCV7349-3 VSTB = 0 V -40 -20 -4 mA Ci Input capacitance (Note 9) - 5 10 pF RECEIVER DATA OUTPUT (Pin RxD) IOH High-level output current Normal mode, VRxD = VIO - 0.4 V -1 -0.4 -0.1 mA IOL Low-level output current VRxD = 0.4 V 1.6 6 12 mA VOH High-level output voltage, Weaker RxD pin in Standby mode is on NCV7349-0 version only Standby mode, IRxD = -100 mA VCC - 1.1 VCC - 0.7 VCC - 0.4 V BUS LINES (Pins CANH and CANL) Vo(reces) (norm) Recessive bus voltage on pins CANH and CANL VTxD = VIO; no load; normal mode 2.0 2.5 3.0 V Vo(reces) (stby) Recessive bus voltage on pins CANH and CANL VTxD = VIO; no load; standby mode -100 0 100 mV Io(reces) (CANH) Recessive output current at pin CANH -35 V < VCANH < +35 V; 0 V < VCC < 5.25 V -2.5 - +2.5 mA Io(reces) (CANL) Recessive output current at pin CANL -35 V < VCANL < +35 V; 0 V < VCC < 5.25 V -2.5 - +2.5 mA 9. Values based on design and characterization, not tested in production www.onsemi.com 7 NCV7349 Table 6. CHARACTERISTICS (VCC = 4.75 V to 5.25 V; VIO = 2.8 V to 5.5 V (NCV7349-3 only); TJ = -40 to +150C; RLT = 60 W unless specified otherwise. On chip versions without VIO pin, reference voltage for all digital inputs and outputs is VCC instead of VIO.) Symbol Parameter Conditions Min Typ Max Unit BUS LINES (Pins CANH and CANL) ILI(CANH) Input leakage current to pin CANH 0 W < R(VCC to GND) < 1 MW VCANL = VCANH = 5 V -10 0 10 mA ILI(CANL) Input leakage current to pin CANL 0 W < R(VCC to GND) < 1 MW VCANL = VCANH = 5 V -10 0 10 mA Vo(dom) (CANH) Dominant output voltage at pin CANH VTxD = 0 V 3.0 3.6 4.25 V Vo(dom) (CANL) Dominant output voltage at pin CANL VTxD = 0 V 0.5 1.4 1.75 V Vo(dif) (bus_dom) Differential bus output voltage (VCANH - VCANL) VTxD = 0 V; dominant; 45 W < RLT < 65 W 1.5 2.25 3.0 V Vo(dif) (bus_rec) Differential bus output voltage (VCANH - VCANL) VTxD = VIO; recessive; no load -120 0 +50 mV Io(sc) (CANH) Short circuit output current at pin CANH VCANH = 0 V; VTxD = 0 V -100 -70 -45 mA Io(sc) (CANL) Short circuit output current at pin CANL VCANL = 36 V; VTxD = 0 V 45 70 100 mA Vi(dif)R (th) Differential receiver threshold voltage - Dominant to Recessive (see Figure 6) -2 V < VCANL < +7 V; -2 V < VCANH < +7 V 0.5 0.6 0.7 V Vi(dif)D (th) Differential receiver threshold voltage - Recessive to Dominant (see Figure 6) -2 V < VCANL < +7 V; -2 V < VCANH < +7 V 0.7 0.8 0.9 V VihcmR(dif) (th) Differential receiver threshold voltage - Dominant to Recessive (see Figure 6) -35 V < VCANL < +35 V; -35 V < VCANH < +35 V 0.4 - 0.8 V VihcmD(dif) (th) Differential receiver threshold voltage - Recessive to Dominant (see Figure 6) -35 V < VCANL < +35 V; -35 V < VCANH < +35 V 0.6 - 1 V VihcmD12(dif) (th) Differential receiver threshold voltage - Both transitions (see Figure 6) -12 V < VCANL < +12 V; -12 V < VCANH < +12 V 0.5 - 0.9 V Vi(dif) (hys) Differential receiver input voltage hysteresis -2 V < VCANL < +7 V; -2 V < VCANH < +7 V 100 200 300 mV Vi(dif) (th)_STDBY Differential receiver threshold voltage in standby mode -12 V < VCANL < +12 V; -12 V < VCANH < +12 V 0.4 0.8 1.15 V Ri(cm) (CANH) Common-mode input resistance at pin CANH 15 26 37 kW Ri(cm) (CANL) Common-mode input resistance at pin CANL 15 26 37 kW Ri(cm) (m) Matching between pin CANH and pin CANL common mode input resistance -3 0 +3 % 25 50 75 kW Ri(dif) VCANH = VCANL Differential input resistance Ci(CANH) Input capacitance at pin CANH VTxD = VIO; (Note 9) - - 30 pF Ci(CANL) Input capacitance at pin CANL VTxD = VIO; (Note 9) - - 30 pF Differential input capacitance VTxD = VIO; (Note 9) - 3.75 10 pF 150 170 185 C Ci(dif) THERMAL SHUTDOWN TJ(sd) Shutdown junction temperature Junction temperature rising TIMING CHARACTERISTICS (see Figure 5 and Figure 8) td(TxD-BUSon) Delay TxD to bus active Ci = 100 pF between CANH to CANL - 50 - ns td(TxD-BUSoff) Delay TxD to bus inactive Ci = 100 pF between CANH to CANL - 60 - ns td(BUSon-RxD) Delay bus active to RxD CRxD = 15 pF - 60 - ns td(BUSoff-RxD) Delay bus inactive to RxD CRxD = 15 pF - 60 - ns 9. Values based on design and characterization, not tested in production www.onsemi.com 8 NCV7349 Table 6. CHARACTERISTICS (VCC = 4.75 V to 5.25 V; VIO = 2.8 V to 5.5 V (NCV7349-3 only); TJ = -40 to +150C; RLT = 60 W unless specified otherwise. On chip versions without VIO pin, reference voltage for all digital inputs and outputs is VCC instead of VIO.) Symbol Parameter Conditions Min Typ Max Unit Propagation delay TxD to RxD (NCV7349-0 version) Ci = 100 pF between CANH to CANL - 125 245 ns Propagation delay TxD to RxD (NCV7349-3 version) Ci = 100 pF between CANH to CANL - 130 250 ns 5 8 20 ms 0.5 2.5 5 ms TIMING CHARACTERISTICS (see Figure 5 and Figure 8) tpd td(stb-nm) twake Delay standby mode to normal mode Dominant time for wake-up via bus tdwakerd Delay to flag wake event (recessive to dominant transitions) (See Figure 4) Valid bus wake-up event, CRxD = 15 pF 1 4.5 10 ms tdwakedr Delay to flag wake event (dominant to recessive transitions) (See Figure 4) Valid bus wake-up event, CRxD = 15 pF 0.5 3.3 7 ms twake(RxD) Minimum pulse width on RxD (See Figure 4) 5 ms tWAKE, CRxD = 15 pF 0.5 - - ms tdom(TxD) TxD dominant time for time-out VTxD = 0 V 1.2 2.6 4 ms 9. Values based on design and characterization, not tested in production Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product performance may not be indicated by the Electrical Characteristics if operated under different conditions. MEASUREMENT SETUPS AND DEFINITIONS recessive TxD recessive dominant 50% 50% CANH CANL 0.9 V Vi(dif) = VCANH - VCANL 0.5 V RxD 0.7 x VCC (*) 0.3 x VCC (*) td(TxD-BUSon) td(TxD-BUSoff) td(BUSon-RXD) td(BUSoff-RXD) tpd tpd *On NCV7349-3 VCC is replaced by VIO Figure 5. Transceiver Timing Diagram www.onsemi.com 9 NCV7349 VRxD High Low Hysteresis 0.9 0.5 Vi(dif)(hys) Figure 6. Hysteresis of the Receiver +5 V 100 nF VCC 3 7 TxD CANH 1 nF 1 NCV7349 RxD 1 nF 4 6 8 CANL 2 GND STB 15 pF Transient Generator 5 Figure 7. Test Circuit for Automotive Transients +5 V 100 nF VCC 3 7 TxD CANH 1 NCV7349 RxD CLT 5 60 W 4 6 8 15 pF RLT 100 pF CANL 2 STB GND Figure 8. Test Circuit for Timing Characteristics DEVICE ORDERING INFORMATION Part Number NCV7349D10R2G NCV7349D13R2G Temperature Range Description High Speed Low Power CAN Transceiver for the Japanese Market -40C to +125C High Speed Low Power CAN Transceiver for the Japanese Market with VIO pin Package Shipping SOIC 150 8 GREEN (Matte Sn, JEDEC MS-012) (Pb-Free) 3000 / Tape & Reel For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. www.onsemi.com 10 NCV7349 PACKAGE DIMENSIONS SOIC 8 CASE 751AZ ISSUE A www.onsemi.com 11 NCV7349 ON Semiconductor and the are registered trademarks of Semiconductor Components Industries, LLC (SCILLC) or its subsidiaries in the United States and/or other countries. SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC's product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5817-1050 www.onsemi.com 12 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative NCV7349/D