SUBMINIATURE SOLID STATE LAMP Part Number: AM2520SURCK03 Hyper Red Features Description z Subminiature package. The Hyper Red source color devices are made with Al- z Gull wing lead. GaInP on GaAs substrate Light Emitting Diode. z Long life - solid state reliability. z Low package profile. z Moisture sensitivity level : level 3. z Package : 1000pcs / reel. z RoHS compliant. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is 0.25(0.01") unless otherwise noted. 3. Lead spacing is measured where the leads emerge from the package. 4. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. 5. The device has a single mounting surface. The device must be mounted according to the specifications. SPEC NO: DSAD1256 REV NO: V.8 DATE: JAN/04/2011 PAGE: 1 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: C.H.Han ERP: 1202000701 Selection Guide Part No. Dice AM2520SURCK03 Lens Type Hyper Red (AlGaInP) Water Clear Viewing Angle [1] Iv (mcd) [2] @ 20mA Min. Typ. 21/2 1500 2400 20 Notes: 1. 1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Luminous intensity/ luminous Flux: +/-15%. Electrical / Optical Characteristics at TA=25C Symbol Parameter Device Typ. peak Peak Wavelength Hyper Red D [1] Dominant Wavelength 1/2 Max. Units Test Conditions 650 nm IF=20mA Hyper Red 630 nm IF=20mA Spectral Line Half-width Hyper Red 28 nm IF=20mA C Capacitance Hyper Red 35 pF VF=0V;f=1MHz VF [2] Forward Voltage Hyper Red 1.95 2.5 V IF=20mA IR Reverse Current Hyper Red 10 uA VR=5V Notes: 1.Wavelength: +/-1nm. 2. Forward Voltage: +/-0.1V. Absolute Maximum Ratings at TA=25C Parameter Hyper Red Units Power dissipation 75 mW DC Forward Current 30 mA Peak Forward Current [1] 185 mA 5 V Reverse Voltage Operating Temperature -40C To +85C Storage Temperature -40C To +85C Note: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. SPEC NO: DSAD1256 REV NO: V.8 DATE: JAN/04/2011 PAGE: 2 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: C.H.Han ERP: 1202000701 Hyper Red AM2520SURCK03 SPEC NO: DSAD1256 REV NO: V.8 DATE: JAN/04/2011 PAGE: 3 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: C.H.Han ERP: 1202000701 AM2520SURCK03 Reflow soldering is recommended and the soldering profile is shown below. Other soldering methods are not recommended as they might cause damage to the product. Recommended Soldering Pattern (Units : mm; Tolerance: 0.1) Reel Dimension Tape Dimensions (Units : mm) SPEC NO: DSAD1256 REV NO: V.8 DATE: JAN/04/2011 PAGE: 4 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: C.H.Han ERP: 1202000701 PACKING & LABEL SPECIFICATIONS AM2520SURCK03 SPEC NO: DSAD1256 REV NO: V.8 DATE: JAN/04/2011 PAGE: 5 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: C.H.Han ERP: 1202000701