SIL30C-12SADJ-VJ - EMERSON�NETWORK POWER

Wide trim range (0.9 Vdc to 5.0 Vdc)

Horizontal and vertical models available

High power density design means reduced board space requirement

Remote sense

Power good output signal (open collector)

Operating ambient temperature to 80 ºCwith suitable derating and forced air cooling

Remote ON/OFF (active high)

Over-temperature protection

0Aminimum load

Input undervoltage lockout

Overcurrent and short-circuit protection

Current sharing option

Available RoHS compliant

SIL30C SERIES

Single output

SIL30C Series | 30 A DC-DC Converter

CClass Non-Isolated

[ 2 YEAR WARRANTY ]

The SIL30C is a new high density open-

frame non-isolated converter series for

space sensitive applications. The

converter has a wide input range

(10.2 Vdc to 13.8 Vdc) and offers a wide

0.9 Vdc to 5 Vdc output voltage range

with a 30 A load. An external resistor

adjusts the output voltage from its preset

value of 0.9 V to any value up to the 5 V

maximum. The SIL has a typical efficiency

of 91%. The series offers remote ON/OFF,

over-temperature protection and over-

current protection as standard.

Its current share facility supports parallel

operation of multiple SIL30C units and the

remote sense feature enables the SIL30C

compensate for voltage drops between

the converters output and the load. With

full international safety approvals including

EN60950 and UL/cUL60950 the SIL30C

reduces compliance costs and time to

market.

File Name:lf_sil30c.pdf Rev (04): 21 Dec 2005

SIL30C Series | 30 A DC-DC Converter

CClass Non-Isolated

Characteristic Symbol Min Typ Max Units Notes and Conditions

Input voltage - turn on Vin (on) 8.5 9.0 9.5 V DC

Input voltage - turn off Vin (off) 7.1 7.6 8.1 V DC

Turn on delay - enabled, Tdelay 30 msec With the Remote ON/OFF signal

then power applied (power) asserted, this is the time from

when the input voltage reaches

the minimum specified operating

voltage until the POWER GOOD

is asserted high

Turnon delay - power Tdelay 30 msec Vin = Vin (nom),then Remote

applied, then Remote ON/OFF (Remote ON/OFF) ON/OFF asserted. This is the

asserted time taken until the POWER

GOOD is asserted high

Output to Power Good Tdelay 8 msec Output voltage in full regulation

delay to POWER GOOD asserted high

Rise time Trise 3 msec From 10% to 90%; full resistive

load, 2 x 680µF external

capacitance

All specifications are typical at nominal input Vin = 12V, full load under any resistive load combination at 25˚Cunless otherwise stated.

Characteristic Symbol Min Typ Max Units Notes and Conditions

Input voltage - operating Vin (oper) 10.2 12.0 13.8 V DC

Input current - no load lin 230 mADC Vin (min) - Vin (max),enabled

Input current - Quiescent lin (off) 30 mADC Converter disabled

Input voltage variation dv/dt 1.0 V/ms

Product was tested at 1.2V/ms.

Much higher dV/dt is possible

(>10V/ms). Consult factoryfor

details

Input Characteristics

Turn On/Off

Absolute Maximum Ratings

File Name:lf_sil30c.pdf Rev (04): 21 Dec 2005

Characteristic Symbol Min Typ Max Units Notes and Conditions

Input voltage - continuous Vin (cont) -0.3 13.8 V DC Vin(+) - Vin(-)

Operating temperature Top 0 80 ºC Measured at thermal reference

points, see Note 1. Higher

ambient operation possible with

forced air cooling. See de-rating

curves

Power Good pull-up voltage 11 V

Storage temperature Tstorage -40 125 ºC

Output current Iout 0 30 A

SIL30C Series | 30 A DC-DC Converter

CClass Non-Isolated

3www.artesyn.com

Characteristic - Signal Name Symbol Min Typ Max Units Notes and Conditions

At remote/control ON/OFF pin See Notes 2 and 3

Open collector or equivalent See Application Note 132 for

compatible Remote ON/OFF details

Control pin open circuit voltage Vih 2.27 2.50 V Iih = 0 µA; open circuit voltage

High level input current Iih 1 µA Current flowing into control pin

when pin is pulled high

(max. at Vih =13.8V)

High level input voltage Vih 2.40 Vin Converter guaranteed on when

control pin is greater than Vih

(max)

Low level input voltage ViI 0.80 V Converter guaranteed off

when control pin is

less than Vil (max)

Low level input current Iil (max) 1.3 mA ViI =0.0 V;

Signal Electrical Interface

File Name:lf_sil30c.pdf Rev (04): 21 Dec 2005

Characteristic Symbol Min Typ Max Units Notes and Conditions

Mean time between failure MTBF 129,386 Hours MIL-HDBK-217F,

Vin = Vin (nom); Iout = Iout

(max);ambient 25ºC;

ground benign environment

Mean time between failure MTBF 4,456,655 Hours Telcordia SR-332

Issue 3, ground benign,

temp. = 40ºC, Vin = Vin (nom),

Iout = Iout (max)

Reliability and Service Life

SIL30C Series | 30 A DC-DC Converter

CClass Non-Isolated

Other Specifications

Material Ratings

Characteristic - Signal Name Notes and Conditions

Flammability rating UL94V-0

Material type FR4 PCB

Characteristic Symbol Min Typ Max Units Notes and Conditions

Switching frequency Fsw 300 kHz Fixed frequency

Weight 28.3 g

Safety Agency Approvals

Characteristic

UL/cUL 60950 File No. E139421

TÜV Product Service IEC 60950 Certificate No. B0211 19870 205

Model Numbers

File Name:lf_sil30c.pdf Rev (04): 21 Dec 2005

Suffix Notes:

Suffix ‘-V’ and suffix ‘-H’ areto be used for non-isolated current sharing applications.

Suffix ‘’-VS’ and suffix ‘-HS’ are to be used for isolated current sharing applications.

Model Input Output Output Current Typical Max. Load

Number Voltage Voltage (Max.) Efficiency Regulation

SIL30C-12SADJ-VJ 12VDC 0.9 - 5.0V 30A 91% ±1.5%

SIL30C-12SADJ-VSJ 12VDC 0.9 - 5.0V 30A 91% ±1.5%

SIL30C-12SADJ-HJ 12VDC 0.9 - 5.0V 30A 91% ±1.5%

SIL30C-12SADJ-HSJ 12VDC 0.9 - 5.0V 30A 91% ±1.5%

RoHS Compliance Ordering Information

The ‘J’ at the end of the part number

indicates that the part is Pb-free

(RoHS 6/6 compliant). TSE RoHS 5/6

(non Pb-free) compliant versions may

be available on special request, please

contact your local sales representative

for details.

SIL30C Series | 30 A DC-DC Converter

CClass Non-Isolated

5www.artesyn.com

File Name:lf_sil30c.pdf Rev (04): 21 Dec 2005

Input Characteristics

0.9V Setpoint

Electrical Characteristics - O/P

0.9V Setpoint

Characteristic Symbol Min Typ Max Units Notes and Conditions

Nominal set-point voltage Vo (nom) 0.873 0.900 0.927 V DC Vin = Vin (nom); Iout = Iout (NL)

Worst case condition over line,

load, temperature and life

Line regulation 0.2 % Vin (min) to Vin (max)

Load regulation 1.5 % Vin = Vin (nom); Iout (min) to

Iout (max)

Output current continuous Iout 0 30 A DC

Output current - shortcircuit Isc 10 A rms Continuous, unit auto recovers

from short, Vo<100mV

Output voltage - noise Vp-p 40 mV pk-pk Measurement bandwidth 20 MHz

Vrms 15 mV rms See Application Note 132 for

measurement set-up details

Current sharing 10 % Iout = Iout (max)

Characteristic Symbol Min Typ Max Units Notes and Conditions

Input current - operating Iin 3.65 A DC Vin = Vin (nom); Iout = Iout

(max.)

Reflected ripple current Iin (ripple) 22 mA RMS Iout = Iout (max.),measured

63 mA pk-pk with external filter. See

Application Note 132 for details

Input capacitance - internal Cinput 18.8 µF

filter

Input capacitance - external Cbypass 270 µF Recommended customer

external input added capacitance.

Maximum ESR = 20mΩ

See Application Note 132 for

ripple current requirements

SIL30C Series | 30 A DC-DC Converter

CClass Non-Isolated

0.9V Setpoint

Efficiency

0.9V Setpoint

Characteristic Symbol Min Typ Max Units Notes and Conditions

Efficiency h 66.8 68.8 % Iout =100% Iout (max),

Vin = Vin (nom)

Efficiency h 71.6 73.6 % Iout =50% Iout (max),

Vin = Vin (nom)

Electrical Characteristics - O/P

0.9V Setpoint

Characteristic Symbol Min Typ Max Units Notes and Conditions

Load transient response - Vdynamic 75 mV Peak deviation for 50% to 75%

peak deviation step load, di/dt = 10A/µsec

Load transient response - Trecovery 150 µsec Settling time to within 1% of

recovery output set point voltage for 50%

to 75% step load

External load capacitance Cext 1,360 µF Maximum capacitor value may

vary with load conditions.

Consult factory for details

Max ESR = 12mΩ

See Application Note 132 for

output capacitance values vs.

stability

Protection and Control Features

Characteristic Symbol Min Typ Max Units Notes and Conditions

Overcurrent limit inception Ioc 43 A DC Vo=90% of Vo(nom)

Open sense voltage 0.9 V DC Sense pins not connected

File Name:lf_sil30c.pdf Rev (04): 21 Dec 2005

SIL30C Series | 30 A DC-DC Converter

7www.artesyn.com

CClass Non-Isolated

File Name:lf_sil30c.pdf Rev (04): 21 Dec 2005

Input Characteristics

2.5V Setpoint

Electrical Characteristics - O/P

2.5V Setpoint

Characteristic Symbol Min Typ Max Units Notes and Conditions

Nominal set-point voltage Vo (nom) 2.425 2.575 2.563 V DC Vin = Vin (nom); Iout = Iout (NL)

Worst case condition over line,

load, temperature and life

Line regulation ±0.2 % Iout = Vin (min) to Vin (max)

Load regulation ±1 % Vin = Vin (nom); Iout (min) to

Iout (max)

Output current continuous Iout 0 30 A DC

Output current - shortcircuit Isc 23.9 A rms Continuous, unit auto recovers

from short, Vo<100mV

Output voltage - noise Vp-p 50 mV pk-pk

Measurement bandwidth 20 MHz

Vrms 15 mV rms See Application Note 132 for

measurement set-up details

Current sharing ±10 % Iout = Iout (max)

Characteristic Symbol Min Typ Max Units Notes and Conditions

Input current - operating Iin 7.59 A DC Vin = Vin (nom); Iout = Iout

(max.)

Reflected ripple current Iin (ripple) 35 mA RMS Iout = Iout (max.),measured

150 mA pk-pk with external filter. See

Application Note 132 for details

Input capacitance - internal Cinput 18.80 µF

filter

Input capacitance - external Cbypass 270 µF Recommended customer

external input added capacitance.

Maximum ESR = 20mΩ

See Application Note 132 for

ripple current requirements

SIL30C Series | 30 A DC-DC Converter

CClass Non-Isolated

2.5V Setpoint

Efficiency

2.5V Setpoint

Characteristic Symbol Min Typ Max Units Notes and Conditions

Efficiency h 81.3 83.3 % Iout =100% Iout (max),

Vin = Vin (nom)

Efficiency h 84.9 86.9 % Iout =50% Iout (max),

Vin = Vin (nom)

Electrical Characteristics - O/P

2.5V Setpoint

Characteristic Symbol Min Typ Max Units Notes and Conditions

Load transient response - Vdynamic 75 mV Peak deviation for 50% to 75%

peak deviation step load, di/dt = 10A/µsec

Load transient response - Trecovery 150 µsec Settling time to within 1% of

recovery output set point voltage for 50%

to 75% step load

External load capacitance Cext 1360 µF Maximum capacitor value may

vary with load conditions.

Consult factory for details

Max ESR = 12mΩ

See Application Note 132 for

output capacitance values vs.

stability

Protection and Control Features

Characteristic Symbol Min Typ Max Units Notes and Conditions

Overcurrent limit inception Ioc 42 A DC Vo=90% of Vo(nom)

Open sense voltage 2.5 V DC Sense pins not connected

File Name:lf_sil30c.pdf Rev (04): 21 Dec 2005

SIL30C Series | 30 A DC-DC Converter

9www.artesyn.com

CClass Non-Isolated

File Name:lf_sil30c.pdf Rev (04): 21 Dec 2005

Input Characteristics

5V Setpoint

Electrical Characteristics - O/P

5V Setpoint

Characteristic Symbol Min Typ Max Units Notes and Conditions

Nominal set-point voltage Vo (nom) 4.85 5.15 5.125 V DC Vin = Vin (nom); Iout = Iout (NL)

Worst case condition over line,

load, temperature and life

Line regulation ±0.2 % Iout = Vin (min) to Vin (max)

Load regulation ±1 % Vin = Vin (nom); Iout (min) to

Iout (max)

Output current continuous Iout 0 30 A DC

Output current - shortcircuit Isc 23.9 A rms Continuous, unit auto recovers

from short, Vo<100mV

Output voltage - noise Vp-p 50 mV pk-pk

Measurement bandwidth 20 MHz

Vrms 15 mV rms See Application Note 132 for

measurement set-up details

Current sharing ±10 % Iout = Iout (max)

Characteristic Symbol Min Typ Max Units Notes and Conditions

Input current - operating Iin 13.62 A DC Vin = Vin (nom); Iout = Iout

(max.)

Reflected ripple current Iin (ripple) 15 mA RMS Iout = Iout (max.),measured

50 mA pk-pk with external filter. See

Application Note 132 for details

Input capacitance - internal Cinput 18.8 µF

filter

Input capacitance - external Cbypass 270 µF Recommended customer

external input added capacitance.

Maximum ESR = 20mΩ

See Application Note 132 for

ripple current requirements

SIL30C Series | 30 A DC-DC Converter

CClass Non-Isolated

5V Setpoint

Efficiency

5V Setpoint

Characteristic Symbol Min Typ Max Units Notes and Conditions

Efficiency h 88.8 90.8 % Iout =100% Iout (max),

Vin = Vin (nom)

Efficiency h 90.7 92.7 % Iout =50% Iout (max),

Vin = Vin (nom)

5V Setpoint

Protection and Control Features

Characteristic Symbol Min Typ Max Units Notes and Conditions

Overcurrent limit inception Ioc 41 A DC Vo=90% of Vo(nom)

Open sense voltage 5 V DC Sense pins not connected

Electrical Characteristics - O/P

Characteristic Symbol Min Typ Max Units Notes and Conditions

Load transient response - Vdynamic 75 mV Peak deviation for 50% to 75%

peak deviation step load, di/dt = 10A/µsec

Load transient response - Trecovery 150 µsec Settling time to within 1% of

recovery output set point voltage for 50%

to 75% step load

External load capacitance Cext 1360 µF Maximum capacitor value may

vary with load conditions.

Consult factory for details

Max ESR = 12mΩ

See Application Note 132 for

output capacitance values vs.

stability

File Name:lf_sil30c.pdf Rev (04): 21 Dec 2005

SIL30C Series | 30 A DC-DC Converter

11 www.artesyn.com

CClass Non-Isolated

File Name:lf_sil30c.pdf Rev (04): 21 Dec 2005

0.9V Model

30 40 50 60 70 80

OUTPUT CURRENT (A)

AMBIENT TEMPERATURE (ºC)

0.5 m/s (100 LFM)

1.0 m/s (200 LFM)

1.5 m/s (300 LFM)

2.0 m/s (400 LFM)

05 10 15 20 25 30

EFFICIENCY (%)

OUTPUT CURRENT (A)

10.2V

12.0V

13.8V

Figure 1: Thermal De-rating Curve Figure 2: Efficiency vs Load and Line

Figure3: ShortCircuit Characteristic

(Channel 1: Output Current at 10A/div,

Channel 4: Output Voltage)

Figure4: Transient Response 50-75%

(Channel 1: Current load step at 2A/div,

Channel 4: Output Voltage deviation)

Figure5: Transient Response 75 - 50%

(Channel 1: Current load step at 2A/div,

Channel 4: Output Voltage deviation)

Figure6: Typical Power Up

(Channel 2: DC Input, Channel 3: Power Good

Channel 4: Output Voltage)

SIL30C Series | 30 A DC-DC Converter

CClass Non-Isolated

0.9V Model

Figure 7: Control On/Off

(Channel 2: Remote ON/OFF, Channel 3: Power Good

Channel 4: Output Voltage)

Figure 8: Typical Ripple and Noise

File Name:lf_sil30c.pdf Rev (04): 21 Dec 2005

SIL30C Series | 30 A DC-DC Converter

CClass Non-Isolated

13 www.artesyn.com

File Name:lf_sil30c.pdf Rev (04): 21 Dec 2005

2.5V Model

30 40 50 60 70 80

OUTPUT CURRENT (A)

AMBIENT TEMPERATURE (ºC)

0.5 m/s (100 LFM)

1.0 m/s (200 LFM)

1.5 m/s (300 LFM)

2.0 m/s (400 LFM)

05 10 15 20 25 30

EFFICIENCY (%)

OUTPUT CURRENT (A)

10.2V

12V

13.8V

Figure 9: Thermal De-rating Curve Figure 10: Efficiency vs Load and Line

Figure11: ShortCircuit Characteristic

(Channel 1: Output Current at 10A/div,

Channel 4: Output Voltage)

Figure12: Transient Response 50-75%

(Channel 1: Current load step at 2A/div,

Channel 4: Output Voltage deviation)

Figure 13: Transient Response 75 - 50%

(Channel 1: Current load step at 2A/div,

Channel 4: Output Voltage deviation)

Figure 14: Typical Power Up

(Channel 2: DC Input, Channel 3: Power Good

Channel 4: Output Voltage)

SIL30C Series | 30 A DC-DC Converter

CClass Non-Isolated

2.5V Model

Figure 15: Control On/Off

(Channel 2: Remote ON/OFF, Channel 3: Power Good

Channel 4: Output Voltage)

Figure 16: Typical Ripple and Noise

File Name:lf_sil30c.pdf Rev (04): 21 Dec 2005

SIL30C Series | 30 A DC-DC Converter

CClass Non-Isolated

15 www.artesyn.com

File Name:lf_sil30c.pdf Rev (04): 21 Dec 2005

5V Model

30 40 50 60 70 80

OUTPUT CURRENT (A)

AMBIENT TEMPERATURE (ºC)

0.5 m/s (100 LFM)

1.0 m/s (200 LFM)

1.5 m/s (300 LFM)

2.0 m/s (400 LFM)

05 10 15 20 25 30

100

EFFICIENCY (%)

OUTPUT CURRENT (A)

10.2V

12V

13.8V

Figure 17: Thermal De-rating Curve Figure 18: Efficiency vs Load and Line

Figure 19: Short Circuit Characteristic

(Channel 1: Output Current at 10A/div,

Channel 4: Output Voltage)

Figure 20: Transient Response 50-75%

(Channel 1: Current load step at 2A/div,

Channel 4: Output Voltage deviation)

Figure21: Transient Response 75 - 50%

(Channel 1: Current load step at 2A/div,

Channel 4: Output Voltage deviation)

Figure22: Typical Power Up

(Channel 2: DC Input, Channel 3: Power Good

Channel 4: Output Voltage)

SIL30C Series | 30 A DC-DC Converter

CClass Non-Isolated

5V Model

Figure 23: Control On/Off

(Channel 2: Remote ON/OFF, Channel 3: Power Good

Channel 4: Output Voltage)

Figure 24: Typical Ripple and Noise

File Name:lf_sil30c.pdf Rev (04): 21 Dec 2005

SIL30C Series | 30 A DC-DC Converter

CClass Non-Isolated

17 www.artesyn.com

File Name:lf_sil30c.pdf Rev (04): 21 Dec 2005

All dimensions in INCHES (mm)

General tolerance ±0.015in (±0.30mm)

except where specified otherwise

0.470

(11.94)

0.150

(3.82)

0.120

(3.05)

0.150

(3.81) Ref.

0.212

(5.38)

0.120

(3.05)

1.350

(34.36)

1.240

(31.40)

0.090

(2.29)

1.200

(30.48)

0.290

(7.46)

0.100

(2.54) Typ.

2.300

(58.42)

2.400

(60.96)

0.050

(1.27)

0.050

(1.27) Ref.

1.250

(31.75

Figure26: Mechanical Drawing - Vertical

2.300

(58.42)

All dimensions in inches (mm)

General tolerance ±0.015in (±0.30mm)

except where specified otherwise

0.025 ±0.001

(0.64) Typ ±0.025

0.050

(1.27)

2.400

(60.96)

1.250

(31.75)

Pin 1

0.100

(2.54) Typ

0.090

(2.29)

0.250

(6.35)

1.200

(30.48)

0.52 ±0.02

(13.20 ±0.5)

0.025 ±0.001

(0.64) Typ ±0.025

0.26 ±0.03

(6.591 ±0.76)

0.062

(1.57) Ref

0.09 ±0.02

(2.4 ±0.5)

0.050

(1.27) Typ

0.140

(3.56 Typ)

0.140

(3.56)

0.019

(0.48) Ref

Figure25: Mechanical Drawing - Horizontal

Note 1

Thermal reference point is defined as the highest temperature

measured at any one of the specified thermal reference points.

See Figure 19: Thermal reference point.

Note 2

The control pin is referenced to Vin-

Note 3

The SIL30C is supplied as standard with active High logic.

Control input pulled low: Unit Disabled

Control input left open: Unit Enabled

Note 4

Thermal reference set up: Unit mounted on an edge card test

board 215mm x 115mm. Test board mounted vertically. For test

details and recommended set-up see Application Note 132 .

Note 5

3-200Hz, sweep at 1/2 octave/min from low to high frequency,

and then from high to low. Thirty minute dwell at all resonant

points.

CAUTION: Hazardous internal voltages and high temperatures.

Ensure that unit is accessible only to trained personnel. The user

must provide the recommended fusing in order to comply with

safety approvals.

SIL30C Series | 30 A DC-DC Converter

CClass Non-Isolated

18 www.artesyn.com

Figure28: Dimensions and Pinout

Pin Connections

Figure 27: Thermal reference points

Pin No. Function

1 TRIM

2 No Pin

3Ground

4 POWER GOOD

5 Not Connected

6Current Share

7 Ground

8 Ground

9Remote ON/OFF

10 Remote Sense (GND)

11 Remote Sense (O/P)

12 Vin

13 Vin

14 Vin

15 Vout

16 Vout

17 Ground

18 Vout

19 Ground

20 Vout

21 Ground

22 Vout

23 Ground

24 Vout

File Name:lf_sil30c.pdf Rev (04): 21 Dec 2005

Longform Datasheet Artesyn Technologies® 2005

The information and specifications contained in this datasheet are

believed to be correct at time of publication. However, Artesyn

Technologies accepts no responsibility for consequences arising

from printing errors or inaccuracies. Specifications aresubject to

change without notice. No rights under any patent accompany the

sale of any such product(s) or information contained herein.

NORTH AMERICA

e-mail: sales.us@artesyn.com

%800 769 7274

%+508 628 5600

EUROPEAN LOCATIONS

e-mail: sales.europe@artesyn.com

IRELAND

%+353 24 93130

AUSTRIA

%+43 1 80150

FAR EAST LOCATIONS

e-mail: sales.asia@artesyn.com

HONG KONG

%+852 2699 2868

19 www.artesyn.com

SIL30C Series | 30 A DC-DC Converter

CClass Non-Isolated