FOR MESSRS: DATE: Mar.06,2009
CUSTOMER’S ACCEPTANCE SPECIFICATIONS
SP14Q006-T
C O N T E N T S
No. ITEM SHEET No. PAGE
1 COVER 7B64PS 2701- SP14Q006-T-7 1-1/1
2 RECORD OF REVISION 7B64PS 2702- SP14Q006-T-7 2-1/2~2/2
3 GENERAL SPECIFICATION 7B64PS 2703- SP14Q006-T-7 3-1/1
4 ABSOLUTE MAXIMUM RATINGS 7B64PS 2704- SP14Q006-T-7 4-1/1
5 ELECTRICAL CHARACTERISTICS 7B64PS 2705- SP14Q006-T-7 5-1/2~2/2
6 OPTICAL CHARACTERISTICS 7B64PS 2706- SP14Q006-T-7 6-1/3~3/3
7 BLOCK DIAGRAM 7B64PS 2707- SP14Q006-T-7 7-1/1
8 INTERFACE TIMING CHART 7B64PS 2708- SP14Q006-T-7 8-1/3~3/3
9 OUTLINE DIMENSIONS 7B63PS 2709- SP14Q006-T-7
7B64PS 2709- SP14Q006-T-7 9-1/2
9-2/2
10 APPEARANCE STANDARD 7B64PS 2710- SP14Q006-T-7 10-1/3~3/3
11 PRECAUTION IN DESIGN 7B64PS 2711- SP14Q006-T-7 11-1/2~2/2
12 DESIGNATION OF LOT MARK 7B64PS 2712- SP14Q006-T-7 12-1/1
13 PRECAUTION FOR USE 7B64PS 2713- SP14Q006-T-7 13-1/1
When products will be discontinued , customers will be informed by HITACHI with
twelve months prior announcement.
ACCEPTED BY; PROPOSED BY;
KAOHSIUNG HITACHI
ELECTRONICS CO.,LTD
P.O. BOX 26-27
2,13TH EAST ST. K.E.P.Z.
KAOHSIUNG TAIWAN R.O.C.
TEL:(07) 821-5811(7 LINE)
FAX:(07) 821-5815
KAOHSIUNG HITACHI
ELECTRONICS CO.,LTD. Sh.
No. 7B64PS 2701- SP14Q006-T-7 PAGE 1-1/1
RECORD OF REVISION
DATE SHEET No. SUMMARY
Jan.16,’03 7B64PS 2705 -
SP14Q006-T-2
PAGE 5 - 2/2
5.2 ELECTRICAL CHARACTERISTICS OF LED BACKLIGHT
SYMBOL TYP. MAX
VLED (TBD) -
ILED 60 -
Revised↓
SYMBOL TYP. MAX
VLED 5 5.2
ILED 160 -
Oct.22,’03 7B64PS2709-
SP14Q006-T-3
Page 9-2/2
Changed LED I/F
JAE/1L-G-4S-S3C2 → JAE/IL-G-4S-S3C2
Mar.24,’04 7B64PS2708-
SP14Q006-T-4
Page 8-3/3
8.3 POWER ON/OFF TIMING SEQUENCE
Revised tDLD min. 200 → 50
Revised tCH max. 200 → 30
7B64PS 2705-
SP14Q006-T-5
Page 5-1/2
5.1 ELECTRICAL CHARACTERISTICS
Added
ITEM SYMBOL MIN. TYP. MAX
Power Supply Voltage Logic VDD-VSS 3.2 3.3 3.4
21.0 22.0 23.0
20.0 21.0 22.0
Recommend LC Driving Voltage
VDD-V0
19.0 20.0 21.0
7B64PS 2706-
SP14Q006-T-5
Page 6-3/3
6.2 OPTICAL CHARACTERISTICS OF BACKLIGHT
Added The LCD driving voltage should be adjusted at the
voltage where the peak contrast is obtained.
Jun.04,’04
7B64PS 2710-
SP14Q006-T-5
Page 10-1/3
10.1 APPEARANCE INSPECTION CONDITION
Revised 45°25°
May.04,’07 7B64PS 2703 –
SP14Q006-T-6
Page 3-1/1
3. GENERAL SPECIFICATIONS
Added
(11) Backlight Type LED(Color : white)
↓
(11) Backlight Type LED(Color : white)
Life time : 40Kh @ 25℃
Note : Life time for half of initial brightness
KAOHSIUNG HITACHI
ELECTRONICS CO.,LTD. DATE Mar.06,’09 7B64PS 2702- SP14Q006-T-7 PAGE 2-1/2
Sh.
No.
RECORD OF REVISION
DATE SHEET No. SUMMARY
7B64PS 2705 –
SP14Q006-T-6
Page 5-2/2
5.2 ELECTRICAL CHARACTERISTICS OF LED BACKLIGHT
Revised
May.04,’07
7B64PS 2712 –
SP14Q006-T-6
Page 12-1/1
12. DESIGNATION OF LOT MARK
Added
REVISION A
Mar.06,’09
7B64PS 2712
SP14Q006-T-7
PAGE 12-1/1
12. DESIGNATION OF LOT MARK
Revised reversion from REV. A to REV.B
KAOHSIUNG HITACHI
ELECTRONICS CO.,LTD. DATE Mar.06,’09 7B64PS 2702- SP14Q006-T-7 PAGE 2-2/2
Sh.
No.
→
Ambient Temperature(℃)
allowable forward current
(mA/pcs)
3. GENERAL SPECIFICATIONS
(1) Part Name SP14Q006-T
(2) Outer Dimensions 167.0(W)mm×109.0(H)mm×10.0 (D) mm max.
(3) Effective Area 120(W)mm min. × 89(H)mm min.
(4) Dot Size 0.345(W)min. × 0.345(H)min.
(5) Dot Pitch 0.360(W)mm × 0.360(H)mm
(6) Dot Number (Resolution) 320 (W) × 240 (H) dots
(7) Duty Ratio 1/240
(8) LCD Type Transflective type F-B / W STN
With anti-glare type upper polarizer
(9) Viewing Direction 6 O’clock
(10) Viewing Angle Viewing Angle in Rear - Front
(12:00) (6:00)
R-F=90 °(typ.)
(11) Backlight Type LED(Color : white)
Life time : 40Kh @ 25℃
Note : Life time for half of initial brightness
KAOHSIUNG HITACHI
ELECTRONICS CO.,LTD. DATE Mar.06,’09 7B64PS 2703- SP14Q006-T-7 PAGE 3-1/1
Sh.
No.
4. ABSOLUTE MAXIMUM RATINGS
4.1 ELECTRICAL ABSOLUTE MAXIMUM RATINGS VSS=0V : STANDARD
ITEM SYMBOL MIN. MAX. UNIT COMMENT
Power Supply for Logic VDD-VSS 0 6.0 V
Power Supply for LC Driving VDD-VEE 0 27.5 V
Input Signal Voltage Vi -0.3 VDD+0.3 V (Note 1)
VESD0 - ±100 V (Note 2,3,4) Static Electricity VESD1 - ±10 kV (Note 2,3,5)
Note 1 : DOFF , FLM , CL1 , CL2 , D0~D3.
Note 2 : Make certain you are grounded when handling LCM.
Note 3 : Energy storage capacitance 200pF , discharge resistance 250Ω Ta=25℃ , 60%RH.
Note 4 : Contact discharge to I/F connector pins.
Note 5 : Contact discharge to front metal bezel.
4.2 ENVIRONMENTAL ABSOLUTE MAXIMUM RATINGS
ITEM OPERATING STORAGE COMMENT
MIN. MAX. MIN. MAX.
Ambient Temperature -20℃ 70℃ -30℃ 80℃ (Note 2,3,6)
Humidity (Note 1) (Note 1) Without Condensation
Vibration
- 2.45m/s2
(0.25G)
- 11.76m/s2
(1.2G)
Note 5
(Note 4)
1h max.
Shock
- 29.4m/s2
(3 G)
- 490.0m/s2
(50 G)
(Note 5)
X、Y、Z Directions
Corrosive Gas Note Acceptable Note Acceptable
Note 1 : Ta≦40℃ : 85%RH max.
Ta＞40℃ : Absolute humidity must be lower than the humidity of 85%RH at 40℃
Note 2 : Ta at -30℃ - - -＜ 48h , at 80℃ - - -＜ 168h.
Note 3 : Background color changes slightly depending on ambient temperature.
This phenomenon is reversible.
Note 4 : 5Hz~100Hz (Except resonance frequency)
Note 5 : This module should be operated normally after finish the test.
Note 6 : The response time will be slower under low temperature.
KAOHSIUNG HITACHI
ELECTRONICS CO.,LTD. DATE Mar.06,’09 7B64PS 2704- SP14Q006-T-7 PAGE 4-1/1
Sh.
No.
5. ELECTRICAL CHARACTERISTICS
5.1 ELECTRICAL CHARACTERISTICS
I T E M SYMBOL CONDITION MIN. TYP. MAX. UNIT COMMENT
4.75 5.0 5.25
Power Supply Voltage
for Logic VDD-VSS - 3.2 3.3 3.4 V
Power Supply Voltage
for LC Driving VEE-VSS - -23.1 -22.0 -20.9 V
H LEVEL 0.8VDD - VDD V
Input Signal Voltage Vi L LEVEL 0 - 0.2VDD V (Note1)
Power Supply Current
for Logic IDD VDD-VSS=5.0V
VEE-VSS= -22.0V - 6.0 - mA (Note2)
Power Supply Current
for LC Driving IEE VDD-VSS=5.0V
VEE-VSS= -22.0V - 5.0 - mA (Note2)
Ta= 0℃ ,
= 0∘21.0 22.0 23.0 V
Ta=25℃ ,
= 0∘20.0 21.0 22.0 V
Recommended LC
Driving Voltage VDD-V0 Ta=50℃ ,
= 0∘19.0 20.0 21.0 V (Note3)
Frame Frequency fFLM - 70 75 80 Hz (Note4)
Note 1 : DOFF , FLM , CL1 , CL2 , D0~D3.
Note 2 : FLM=75Hz , test pattern is all “Q”.
VDD-V0=21.0V , Ta=25℃
Note 3 : Recommended LC driving voltage may fluctuate about ±1.0V by each module.
Test pattern is all “Q”
Note 4 : Please set the frame frequency so as to avoid flicker and rippling on the display.
KAOHSIUNG HITACHI
ELECTRONICS CO.,LTD. DATE Mar.06,’09 7B64PS 2705- SP14Q006-T-7 PAGE 5-1/2
Sh.
No.
5.2 ELECTRICAL CHARACTERISTICS OF LED BACKLIGHT
ITEM SYMBOL CONDITION MIN. TYP. MAX. UNIT COMMENT
Power Supply Voltage
for LED VLED - - 5.0 5.2 V
Power Supply Current
for LED ILED VLED=5.0V - 160 - mA (Note 1)
Note 1 : The ILED changes depending on ambient temperature.
KAOHSIUNG HITACHI
ELECTRONICS CO.,LTD. DATE Mar.06,’09 7B64PS 2705- SP14Q006-T-7 PAGE 5-2/2
Sh.
No.
Ambient Temperature(℃)
allowable forward current
(mA/pcs)
6.2 OPTICAL CHARACTERISTICS OF BACKLIGHT
(Backlight ON)
I T E M MIN. TYP. MAX. UNIT NOTE
Brightness - 60 - cd/m2 ILED=160mA
Brightness Uniformity - - ±30 % (Note 1)
Ta=25℃, Display data should be all “ON”.
The LCD driving voltage should be adjusted at the voltage where
the peak contrast is obtained.
Note 1 : Measure of the following 9 places on the display.
Definition of the brightness tolerance.
Y=240Y=160Y=80
X=60
X=120
X=180
Average Brightness
Max. or Min. Brightness-Average Brightness x 100
( )
KAOHSIUNG HITACHI
ELECTRONICS CO.,LTD. DATE Mar.06,’09 7B64PS 2706- SP14Q006-T-7 PAGE 6-3/3
Sh.
No.
D0~D3
FLM
CL1
DOFF
CL2
IC4
320×240 DOTS
IC2
: TIMING CIRCUIT
D0
D1 D2
IC1
X240
D3
X1
X81
X161
X160
X240
X80
X1
IC5
IC6
IC7
POWER
SUPPLY
LED Back Light
VDD
VSS
V0
VEE
VLED(-)
VLED(+)
Y320
Y241
Y160
Y81
Y80
Y1
7. BLOCK DIAGRAM
KAOHSIUNG HITACHI
ELECTRONICS CO.,LTD. DATE Mar.06,’09 7B64PS 2707- SP14Q006-T-7 PAGE 7-1/1
Sh.
No.
8. INTERFACE TIMING CHART
8.1 INTERFACE TIMING CHART
KAOHSIUNG HITACHI
ELECTRONICS CO.,LTD. DATE Mar.06,’09 7B64PS 2708- SP14Q006-T-7 PAGE 8-1/3
Sh.
No.
52.1s≦T≦59.5s
X1 X2
X240
CL1
CL2
D3
D2
D1
D0
FLM
CL1
FLM
D0~D3 X1 X2 X239 X240
240×T
Y1 Y5 Y317
Y2 Y6 Y318
Y3 Y7 Y319
Y4 Y8 Y320
8.2 TIMING CHARACTERISTICS
ITEM SYMBOL MIN. TYP. MAX. UNIT
CL2 frequency fCP - - 6.5 MHz
CL2 pulse width tw 45 - - ns
CL2 rise, fall time tr,tf - - 15 ns
Data set up time tDSU 30 - - ns
Data hold time tDHD 30 - - ns
CL1 set up time tLSU 80 - - ns
CL1 clock time tLC 120 - - ns
“FLM” set up time tSETUP 100 - - ns
“FLM” hold time tHOLD 100 - - ns
“CL1” pulse width twc 125 - - ns
KAOHSIUNG HITACHI
ELECTRONICS CO.,LTD. DATE Mar.06,’09 7B64PS 2708- SP14Q006-T-7 PAGE 8-2/3
Sh.
No.
tw tw
tw
CL2
tDSU tDHD
D0~D3
tLC
tLSU
CL1 twc
tSETUP tHOLD
FLM
0.2VDD
0.8VDD
tf tr
0.2VDD
0.8VDD
0.2VDD
0.8VDD
0.2VDD
0.8VDD
0.2VDD
0.8VDD
0.2VDD
0.8VDD 0.2VDD
0.8VDD
0.2VDD
0.8VDD
0.2VDD
0.8VDD
0.2VDD
0.8VDD
0.8VDD 0.8VDD
8.3 POWER ON/OFF TIMING SEQUENCE
SYMBOL MIN. MAX. UNIT COMMENT
tDLD 50 - ms
tCH 0 30 ms (Note 1)
tLDH 0 - ms
tDOr - 100 ns
tDOf - 100 ns
tDLCr 0 - ms (Note 2)
tDLCf 0 - ms
tDLCs 20 - ms
Note 1 : Please keep the specified sequence because wrong
sequence may cause permanent damage to the LCD panel.
Note 2 : HITACHI recommends you to use DOFF function.
Display quality may deteriorate if you don‘t use DOFF function.
8.4 POWER SUPPLY FOR LCM (EXAMPLE)
Note 1 : VR : 10k
tDLD tDLD
tCH tCH
tDLC r tDL Cf
tDLCs
tDL Cs
tLDH tDOr tDOf tLDH
0.8VDD 0.8VDD
0.8VDD 0.8VDD
0.2VDD0.2VDD
VDD
SIGNAL
DOFF
GND
GND
VEE GND
GND
0.95VDD0.95VDD
LCM
VDD
VSS
VEE
VR
V0
+5.0V
-22.0
V
KAOHSIUNG HITACHI
ELECTRONICS CO.,LTD. DATE Mar.06,’09 7B64PS 2708- SP14Q006-T-7 PAGE 8-3/3
Sh.
No.
9.2 DISPLAY PATTERN
9.3 INTERFACE PIN CONNECTION
FPC：pitch 1.25mm 14 pins
INTERFACE PIN No. SIGNAL LEVEL FUNCTION
LCM CN1 1 D0 H/L Display Data
2 D1
3 D2
4 D3
5 DOFF H/L H : ON / L : OFF
6 FLM H First Line Marker
7 N.C - -
8 CL1 HL Data Latch
9 CL2 HL Data Shift
10 VDD - Power Supply for Logic
11 VSS - GND
12 VEE - Power Supply for LC
13 V0 - Operating Voltage LC Driving
14 VSS - GND
INTERFACE PIN No. SIGNAL LEVEL FUNCTION
1 VLED(+) - Power Supply for LED
2 N.C - -
3 N.C - -
LCM CN2
4 VLED(-) - LED GND
LED I/F : J.A.E / IL – G - 4S – S3C2-SA
0.36
0.345
0.36
0.345
Scale : NTS
Unit : mm
Measurement Tolerance : ±0.1
115.185 (320 dots)
86.385 (240 dots)
KAOHSIUNG HITACHI
ELECTRONICS CO.,LTD. DATE Mar.06,’09 7B64PS 2709- SP14Q006-T-7 PAGE 9-2/2
Sh.
No.
10. APPEARANCE STANDARD
10.1 APPEARANCE INSPECTION CONDITION
Visual inspection should be done under the following condition.
(1) The inspection should be done under in the dark room.
(2) The CFL should be lighted with the prescribed inverter.
(3) The distance between eyes of an inspector and the LCD module is 25cm.
(4) The viewing zone is shown the figure .
10.2 DEFINITION OF EACH ZONE
A zone : Within the effective area specified at page 9-1/2 of this document.
B zone : Area between the window of metal frame and the effective area line
specified at page 9-1/2 of this document.
LCD
Bezel
eye eye
25° 25°
Window of Metal Frame
Effective Area
A zone
B zone
KAOHSIUNG HITACHI
ELECTRONICS CO.,LTD. DATE Mar.06,’09 7B64PS 2710- SP14Q006-T-7 PAGE 10-1/3
Sh.
No.
Viewing angle ≦25°
10.3 APPEARANCE SPECIFICATION
*) If a problem occurs in respect to any of these items ,
both parties(Customer and HITACHI) will discuss in more detail.
No. ITEM CRITERIA A B
Scratches Distinguished one is not acceptable
(To be judged by HITACHI limit sample) -
Dent Same as Above -
Wrinkles in Polarizer Same as Above -
Bubbles Average Diameter
D(mm) Maximum Number
Acceptable
D≦0.2 Ignore
0.2＜D≦0.3 12 ○-
0.3＜D≦0.5 3
0.5＜D None
Stains, Filamentous
Foreign Materials,
Dark Spot Length
L(mm) Width
W(mm) Maximum Number
Acceptable ○-
L≦2.0 W≦0.03 Ignore
L≦3.0 0.03＜W≦0.05 6
L≦2.5 0.05＜W≦0.1 1
Round
Average
Diameter
D(mm)
Maximum Number
Acceptable Minimum
Space
D＜0.2 Ignore - ○-
0.2 ≦D＜0.33 8 10mm
0.33≦D None -
Total Filamentous + Round = 10
Those wiped out easily are acceptable ○ ○
Color Tone To be judged by HITACHI limit sample ○-
Color Uniformity Same as above ○-
Pinhole Average Diameter
D(mm) Maximum Number
Acceptable
D≦0.15 Ignore
0.15＜D≦0.3 10
C≦0.015 Ignore
Contrast
Irregularity
(Spot)
Average
Diameter
D(mm)
Contrast Maximum
Number
Acceptable
Minimum
Space ○-
D≦0.25 To be Ignore -
0.25＜D≦0.35 judged by 10 20mm
0.35＜D≦0.5 HITACHI 4 20mm
L
C
D
0.5 ＜D None -
KAOHSIUNG HITACHI
ELECTRONICS CO.,LTD. DATE Mar.06,’09 7B64PS 2710- SP14Q006-T-7 PAGE 10-2/3
Sh.
No.
11. PRECAUTION IN DESIGN
11.1 LC DRIVING VOLTAGE (VEE) AND VIEWING ANGLE RANGE
Setting VEE out of the recommended condition will be a cause for a change of
viewing angle range.
11.2 PRECAUTIONS AGAINST STATIC CHARGE
As this module contains C-MOS LSIs , it is not strong against electrostatic discharge.
Make certain that the operator’s body is connected to the ground through a list
band etc. And don’t touch I/F pins directly.
11.3 POWER ON SEQUENCE
Input signals should not be applied to LCD module before power supply voltage is
applied and reaches to specified voltage (VDD).
If above sequence is not kept, C-MOS LSIs of LCD modules may be damaged due
to latch up problem.
11.4 PACKAGING
(1) No leaving product is preferable in the place of high humidity for a long period of
time. For their storage in the place where temperature is 35 ℃ or higher ,special care
t o p r e v e n t t he m f r o m hi gh h um i d ity i s r e q ui r e d. A c om b in a t io n of high temperature and
high humidity may cause them polarization degradation as well as bubble generation
and polarizer peel-off. Please keep the temperature and humidity within the specified
range for use and storage.
(2) Since polarizers tend to be easily damaged, They should be handled full
with care so as not to get them touched, pushed or rubbed.
(3) As the adhesives used for adhering polarizers are made of organic substances
which will be deteriorated by a chemical reaction with such chemicals as acetone, toluene ,
ethanol and isopropyl alcohol. The following solvents are recommended for use:
normal hexane
Please contact us when it is necessary for you to use chemicals.
(4) Lightly wipe to clean the dirty surface with absorbent cotton waste or other soft
material like chamois , soaked in the chemicals recommended without scrubbing it
hardly. To prevent the display surface from damage and keep the appearance in good
s t a t e , i t i s s u f f ici e n t , in g ene r a l , t o w ip e it with absorbent cotton.
(5) Immediately wipe off saliva or water drop attached on the display area because its
long period adherence may cause deformation or faded color on the spot.
(6) Foggy dew deposited on the surface due to coldness will be caused for polarizer
damage, stain and dirt on product. When necessary to take out the products from
some place at low temperature for test, etc. It is required for them to be warmed
up in a container once at the temperature higher than that of room.
(7) Touching the display area and contact terminals with bare hands and contaminating
them are prohibited, because the stain on the display area and poor insulation
between terminals are often caused by being touched by bare hands.
(Some cosmetics are detrimental to polarizers.)
KAOHSIUNG HITACHI
ELECTRONICS CO.,LTD. DATE Mar.06,’09 7B64PS 2711- SP14Q006-T-7 PAGE 11-1/2
Sh.
No.
(8) In general the quality of glass is fragile so that it tends to be cracked or chipped in
handling, specially on its periphery. Be careful not to give it sharp shock caused by
dropping down, etc.
11.5 CAUTION FOR OPAERATION
(1) It is an indispensable condition to drive LCDs within the specified voltage limit since
the higher voltage than the limit causes the shorter LCD life. An electrochemical
reaction due to direct current causes LCDs undesirable deterioration , so that the use
of direct current driver should be avoided.
(2) Response time will be extremely delayed at lower temperature than the operating
temperature range and on the other hand at higher temperature LCDs show dark blue
color in them. However those phenomena do not mean malfunction or out of order
with LCDs which will come back in the specified operating temperature range.
(3) If the display area is pushed hard during operation, some font will be abnormally
displayed but it resumes normal condition after turning off once.
(4) A slight dew depositing on terminals is a cause for electrochemical reaction resulting
in terminal open circuit. Please operate the LCD module under the relative condition of
40℃ 85%RH.
11.6 STORAGE
In case of storing for a long period of time (for instance , for years) for the purpose of
replacement use , the following ways area recommended.
(1) Storage in a polyethylene bag with the opening sealed , so the fresh air will not
be entered from outside .
(2) Placing in a dark place where neither exposure to direct sunlight nor light is , keeping
temperature in the range from 0 ℃ to 35 ℃.
(3) Storing with no touch on polarizer surface by anything else. (It is recommended to
store them as they have been contained in the inner container at the time of delivery
from us.)
11.7 SAFETY
(1) It is recommendable to crash damaged or unnecessary LCDs into pieces and wash
off liquid crystal by either of solvents such as acetone and ethanol , which should be
burned up later.
(2) When any liquid leaked out of a damaged glass cell comes in contact with your
hands , please wash it off well with soap and water.
KAOHSIUNG HITACHI
ELECTRONICS CO.,LTD. DATE Mar.06,’09 7B64PS 2711- SP14Q006-T-7 PAGE 11-2/2
Sh.
No.
12. DESIGNATION OF LOT MARK
12.1 LOT MARK
Lot mark is consisted of 5 digits for production lot and
6 digits for production control.
12.2 SERIAL No.
Serial No. is consisted of 6 digits number (000001~999999).
12.3 LOCATION OF LOT MARK
Label is bring attached on the back side of module.
12.4 REVISION(Rev.) CONTROL
Rev No. ITEM
A Mcount IC :MN73099HED(Panasonic)
Transistor :2SA1036K(ROHM)
B Mcount IC :IT7001M(ITE)
Transistor :2SA1576(ROHM)
Week
(day in calendar) Figure in
lot mark
1~ 7 1
8~14 2
15~21 3
22~28 4
29~31 5
Month Figure in
lot mark Month Figure in
lot mark
Jan. 01 Jul. 07
Feb. 02 Aug. 08
Mar. 03 Sep. 09
Apr. 04 Oct. 10
May 05 Nov. 11
Jun. 06 Dec. 12
Year Figure in
lot mark
2009 9
2010 0
2011 1
2012 2
2013 3
1408
Year
Month
Week
T
Digits for production control
T : Made in Taiwan
KAOHSIUNG HITACHI
ELECTRONICS CO.,LTD. DATE Mar.06,’09 7B64PS 2712- SP14Q006-T-7 PAGE 12-1/1
Sh.
No.
SP14Q006-T B
13. PRECAUTION FOR USE
13.1 A limit sample should be provided by the both parties on an occasion when the both
parties agreed its necessity. Judgment by a limit sample shall take effect after the
limit sample has been established and confirmed by the both parties.
13.2 On the following occasions, the handling of the problem should be decided through
discussion and agreement between responsible persons of the both parties.
(1) When a question is arisen in the specifications.
(2) When a new problem is arisen which is not specified in this specifications.
(3) When an inspection specifications change or operating condition change in customer
is reported to HITACHI, and some problem is arisen in this specification due to the
change.
(4) When a new problem is arisen at the customer’s operating set for sample evaluation
in the customer site.
The precaution that should be observed when handling LCM have been explained
above. If any points are unclear or if you have any request , please contact HITACHI.
KAOHSIUNG HITACHI
ELECTRONICS CO.,LTD. DATE Mar.06,’09 7B64PS 2713- SP14Q006-T-7 PAGE 13-1/1
Sh.
No.
