MIC22205 2A, Integrated, Switch, High-Efficiency, Synchronous Buck Regulator with Frequency Programmable up to 4MHz General Description Features The Micrel MIC22205 is a high-efficiency, 2A, integrated switch, synchronous buck (step-down) regulator. The MIC22205 is optimized for highest efficiency, achieving more than 95% efficiency while still switching at 1MHz. The ultra-high speed control loop keeps the output voltage within regulation even under the extreme transient load swings commonly found in FPGAs and low-voltage ASICs. The output voltage is pre-bias safe and can be adjusted down to 0.7V to address all low-voltage power needs. The MIC22205 offers a full range of sequencing and tracking options. The Enable/Delay (EN/DLY) pin, combined with the Power Good (PG) pin, allows multiple outputs to be sequenced in any way during turn-on and turn-off. The Ramp ControlTM (RC) pin allows the device to be connected to another product in the MIC22xxx and/or MIC68xxx family, to keep the output voltages within a certain V on start-up. (R) The MIC22205 is available in a 12-pin 3mm x 3mm MLF with a junction operating range from -40C to +125C. Data sheets and support documentation can be found on Micrel's web site at: www.micrel.com. * * * * * * * * * * * * * * * Input voltage range: 2.9V to 5.5V Output voltage adjustable down to 0.7V Output load current up to 2A Safe start-up into a pre-biased output Full sequencing and tracking capability Power Good (PG) output Efficiency > 95% across a broad load range Programmable frequency 300kHz to 4MHz Ultra-fast transient response Easy RC compensation 100% maximum duty cycle Fully-integrated MOSFET switches Thermal-shutdown and current-limit protection 12-pin 3mm x 3mm MLF(R) -40C to +125C junction temperature range Applications * * * * * High power density point-of-load conversion Servers, routers, and base stations DVD recorders / Blu-ray players Computing peripherals FPGAs, DSP, and low-voltage ASIC power _________________________________________________________________________________________________________________________ Typical Application Efficiency (VIN = 5V) vs. Output Current 100 3.3V 95 EFFICIENCY (%) 90 85 1.8V 80 75 70 65 VIN = 5V 60 55 50 0 MIC22205 2A 1MHz Synchronous Output Converter 0.5 1 1.5 2 OUTPUT CURRENT (A) Ramp Control is a trademark of Micrel, Inc. MLF and MicroLeadFrame are registered trademarks of Amkor Technology, Inc. Micrel Inc. * 2180 Fortune Drive * San Jose, CA 95131 * USA * tel +1 (408) 944-0800 * fax + 1 (408) 474-1000 * http://www.micrel.com August 2011 M9999-082511-A Micrel, Inc. MIC22205 Ordering Information Part Number MIC22205YML Voltage Adjustable Package(1) Junction Temperature Range -40 to +125C 12-Pin 3mm x 3mm MLF Lead Finish (R) Pb-Free Note: (R) 1. MLF is a GREEN ROHS compliant package. Lead finish is NiPdAu. Mold compound is Halogen Free. Pin Configuration 12-Pin 3mm x 3mm MLF(R) (ML) Pin Description Pin Number Pin Name Description PG (output): This is an open drain output that indicates when the output voltage is below 90% of its nominal voltage. The PG flag is asserted without delay when the enable is set low or when the output goes below the 90% threshold. Ramp Control: A capacitor from the RC pin-to-ground determines slew rate of output voltage during start-up. The RC pin is internally fed with a 1A current source. The output voltage tracks the RC pin voltage. The slew rate is proportional by the internal 1A source and the RC pin capacitor. This feature can be used for tracking capability as well as soft start. 1 PG 2 RC 3 CF Adjustable frequency with external capacitor. Refer to Table 2. 4 SGND Signal Ground: Internal signal ground for all low power circuits. 5 COMP Compensation Pin (Input): The MIC22205 uses an internal compensation network containing a fixed-frequency zero (phase lead response) and pole (phase lag response) which allows the external compensation network to be much simplified for stability. The addition of a single capacitor and resistor to the COMP pin will add the necessary pole and zero for voltage mode loop stability using low-value, low-ESR ceramic capacitors. 6 FB 7 SVIN Signal Power Supply Voltage (Input): This pin is connected externally to the PVIN pin. A 2.2F ceramic capacitor from the SVIN pin to SGND must be placed next to the IC. 8 PVIN Power Supply Voltage (Input): The PVIN pins are the input supply to the internal P-Channel Power MOSFET. A 10F ceramic is recommended for bypassing at each PVIN pin. The SVIN pin must be connected to a PVIN pin. 9 SW August 2011 Feedback: Input to the error amplifier. The FB pin is regulated to 0.7V. A resistor divider connecting the feedback to the output is used to adjust the desired output voltage. Switch (Output): This is the connection to the drain of the internal P-Channel MOSFET and drain of the N-Channel MOSFET. This is a high-frequency, high-power connection; therefore traces should be kept as short and as wide as practical. 2 M9999-082511-A Micrel, Inc. MIC22205 Pin Description (Continued) Pin Number Pin Name 10 PGND Power Ground: Internal ground connection to the source of the internal N-Channel MOSFETs. 11 NC No Connect: Leave this pin open. Do not connect to ground or route other signal through this. 12 EN/DLY Enable/Delay (Input): This pin is internally fed with a 1A current source from SVIN. A delayed turn on is implemented by adding a capacitor to this pin. The delay is proportional to the capacitor value. The internal circuits are held off until EN/DLY reaches the enable threshold of 1.24V. This pin is pulled low when the input voltage is lower than the UVLO threshold. EP GND August 2011 Description Exposed Pad (Power): Must be connected to the GND plane for full output power to be realized. 3 M9999-082511-A Micrel, Inc. MIC22205 Absolute Maximum Ratings (1) Operating Ratings (3) PVIN to PGND.................................................... -0.3V to 6V SVIN to PGND..................................................-0.3V to PVIN VSW to PGND...................................................-0.3V to PVIN VEN/DLY to PGND .............................................. -0.3V to PVIN VPG to PGND ...................................................-0.3V to PVIN Junction Temperature ................................................ 150C PGND to SGND ............................................. -0.3V to 0.3V Storage Temperature Range ....................-65C to +150C Lead Temperature (soldering, 10s)............................ 260C ESD Rating.................................................................Note 2 Supply Voltage (PVIN/SVIN) ...............................2.9V to 5.5V Power Good Voltage (VPG) .................................. 0V to PVIN Enable Input (VEN/DLY) .......................................... 0V to PVIN Junction Temperature (TJ) ..................-40C TJ +125C Package Thermal Resistance 3mm x 3mm MLF(R)-12 (JC) ............................ 28.7C/W 3mm x 3mm MLF(R)-12 (JA) ............................... 40C/W Electrical Characteristics (4) SVIN = PVIN = VEN/DLY = 3.3V, VOUT = 1.8V, TA = 25C, unless noted. Bold values indicate -40C< TJ < +125C. Parameter Condition Min. PVIN rising 2.9 2.55 Typ. Max. Units 5.5 2.9 V V mV mA A Power Input Supply Input Voltage Range (PVIN) Under-Voltage Lockout Trip Level UVLO Hysteresis Quiescent Supply Current Shutdown Current Reference Feedback Reference Voltage Load Regulation Line Regulation FB Bias Current Enable Control EN/DLY Threshold Voltage EN Hysteresis EN/DLY Bias Current RC Ramp Control RC Pin Source Current Oscillator Switching Frequency Maximum Duty Cycle Short Current Protection Current Limit Internal FETs VFB = 0.9V (not switching) VEN/DLY = 0V 2.719 418 1.3 5 2 10 0.686 0.7 0.2 0.2 1 0.714 V % % nA 1.14 1.34 1.8 V mV A IOUT = 100mA to 2A VIN = 2.9V to 5.5V; IOUT = 100mA VFB = 0.5V VEN/DLY = 0.5V; VIN = 2.9V and VIN = 5.5V 0.6 1.24 12 1.0 VRC = 0.35V 0.5 1.0 1.7 A 0.8 100 1.0 1.2 VFB 0.5V MHz % VFB = 0.5V 2 5.5 8 A Top MOSFET RDS(ON) VFB = 0.5V, ISW = 1A 180 m Bottom MOSFET RDS(ON) VFB = 0.9V, ISW = -1A 100 m Notes: 1. Exceeding the absolute maximum rating may damage the device. 2. Devices are ESD sensitive. Handling precautions recommended. 3. The device is not guaranteed to function outside its operating rating. 4. Specification for packaged product only. August 2011 4 M9999-082511-A Micrel, Inc. MIC22205 Electrical Characteristics (4) (Continued) SVIN = PVIN = VEN/DLY = 3.3V, VOUT = 1.8V, TA = 25C, unless noted. Bold values indicate -40C< TJ < +125C. Parameter Condition Min. Typ. Max. -10 -12.5 Units Power Good (PG) PG Threshold Threshold % of VFB from VREF Hysteresis PG Output Low Voltage 2.843 IPG = 5mA (sinking), VEN/DLY = 0V PG Leakage Current VPG = 5.5V; VFB = 0.9V Over-Temperature Shutdown TJ Rising 5 % % 139 mV 1.0 2.0 Over-Temperature Shutdown Hysteresis August 2011 -7.5 A 151 C 16 C M9999-082511-A Micrel, Inc. MIC22205 Typical Characteristics 0.724 IOUT = 0A SWITCHING 12 10 8 6 VEN/DLY = 0V 8 6 4 2 2.5 3.0 3.5 4.0 4.5 5.0 5.5 3.0 4.0 4.5 5.0 0.2% 0.0% -0.2% -0.4% 4.5 5.0 5.5 8 6 4 3.5 4.0 4.5 5.0 1.20 850 5.5 Falling 1.10 2.5 3.0 3.5 4.0 4.5 INPUT VOLTAGE (V) Power Good Threshold/VREF Ratio vs. Input Voltage 14.0 VEN/DLY = VIN 1.25 VPG THRESHOLD/VREF (%) ENABLE INPUT CURRENT (A) 900 5.0 Rising 5.5 1.50 950 5.5 1.30 Enable Input Current vs. Input Voltage 1000 5.0 1.00 3.0 Switching Frequency vs. Input Voltage IOUT = 0A 4.5 1.40 INPUT VOLTAGE (V) VOUT = 1.8V 4.0 Enable Threshold vs. Input Voltage VOUT = 1.8V 2.5 1100 3.5 1.50 INPUT VOLTAGE (V) 1050 3.0 INPUT VOLTAGE (V) 0 4.0 0.684 2.5 2 3.5 0.692 5.5 ENABLE THRESHOLD (V) VOUT = 1.8V IOUT = 0A to 2A CURRENT LIMIT (A) TOTAL REGULATION (%) 3.5 10 3.0 0.700 Current Limit vs. Input Voltage 0.6% 2.5 VOUT = 1.8V 0.708 INPUT VOLTAGE (V) Load Regulation vs. Input Voltage 0.4% 0.716 0.676 2.5 INPUT VOLTAGE (V) SWITCHING FREQUENCY (kHz) FEEDBACK VOLTAGE (V) VOUT = 1.8V 14 Feedback Voltage vs. Input Voltage 10 SHUTDOWN CURRENT (A) 16 SUPPLY CURRENT (mA) VIN Shutdown Current vs. Input Voltage VIN Operating Supply Current vs. Input Voltage 1.00 0.75 0.50 0.25 13.0 12.0 11.0 10.0 VREF = 0.7V 9.0 0.00 2.5 3.0 3.5 4.0 4.5 INPUT VOLTAGE (V) 5.0 5.5 2.5 3.0 3.5 4.0 4.5 INPUT VOLTAGE (V) 5.0 5.5 8.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 INPUT VOLTAGE (V) August 2011 6 M9999-082511-A Micrel, Inc. MIC22205 Typical Characteristics (Continued) VIN Shutdown Current vs. Temperature VIN Operating Supply Current vs. Temperature 15 VIN =3.3V VOUT = 1.8V 12.0 IOUT = 0A SWITCHING 10.0 8.0 2.9 IOUT = 0A 12 VEN/DLY = 0V 9 3.76 6 3 -25 0.724 0 25 50 75 100 2.4 Falling -25 0 25 50 75 100 -50 125 -25 0 25 50 75 TEMPERATURE (C) Feedback Voltage vs. Temperature Load Regulation vs. Temperature Line Regulation vs. Temperature 0.6% LOAD REGULATION (%) VOUT = 1.8V IOUT = 0A 0.708 0.700 0.692 0.684 -25 0 25 50 75 100 0.4% VOUT = 1.8V IOUT = 0A to 2A 0.2% 0.0% -0.2% -25 Switching Frequency vs. Temperature 0 25 50 75 100 -50 V IN = 3.3V V OUT = 1.8V IOUT = 0A 850 0 25 50 75 100 TEMPERATURE (C) 125 0 25 50 75 100 125 Current Limit vs. Temperature 10 Rising 1.26 1.24 1.22 VIN = 3.3V 1.20 1.18 1.16 1.14 Falling 8 6 4 V IN = 3.3V V OUT = 1.8V 2 1.12 1.10 800 -25 -25 TEMPERATURE (C) CURRENT LIMIT (A) ENABLE THRESHOLD (V) 950 900 -0.1% 125 1.28 1000 125 0.0% Enable Threshold vs. Temperature 1050 100 VIN = 2.9V to 5.5V VOUT = 1.8V 0.1% TEMPERATURE (C) TEMPERATURE (C) 1100 125 -0.2% -50 125 100 0.2% VIN = 3.3V -0.4% 0.676 August 2011 2.5 TEMPERATURE (C) 0.716 -50 2.6 TEMPERATURE (C) VIN = 3.3V -50 2.7 2.2 -50 125 LINE REGULATION (%) -50 Rising 2.8 2.3 0 6.0 FEEDBACK VOLTAGE (V) 3.0 VIN = 3.3V VIN THRESHOLD (V) SHUTDOWN CURRENT (uA) SUPPLY CURRENT (mA) 14.0 SWITCHING FREQUENCY (kHz) VIN UVLO Threshold vs. Temperature 0 -50 -25 0 25 50 75 TEMPERATURE (C) 7 100 125 -50 -25 0 25 50 75 TEMPERATURE (C) M9999-082511-A Micrel, Inc. MIC22205 Typical Characteristics (Continued) Feedback Voltage vs. Output Current Efficiency vs. Output Current 0.724 FEEDBACK VOLTAGE (V) 3.3VIN 95 5.0VIN 85 80 75 70 65 VOUT = 1.8V 60 VIN = 2.9V to 5.5V 0.716 0.708 0.700 0.692 VIN = 3.3V 0.684 55 0.676 50 0.5 1 1.5 OUTPUT CURRENT (A) 2.0 0.0 VIN = 5.0V 1.0 1.5 2.0 3.8 3.3 TA 2.8 25C 85C 125C 0.84 0.5 POWER DISSIPATION (W) 2.5V 1.8V 1.5V 1.2V 1.0V 0.9V 0.8V 0.7V 75 70 65 VIN = 3.3V 55 50 1.2 1.8 2.4 OUTPUT CURRENT (A) 1.0 1.5 5.0 TA 4.5 2.0 25C 85C 125C 0.0 3 Curves Top to Bottom 0.72 3.3V 2.5V 1.8V 1.5V 1.2V 1.0V 0.9V 0.8V 0.7V 0.60 0.48 0.36 0.24 0.5 1.0 1.5 2.0 OUTPUT CURRENT (A) IC Power Dissipation (VIN = 3.3V) vs. Output Current 90 80 5.5 OUTPUT CURRENT (A) 85 2.0 4.0 0.0 95 0.6 1.5 VFB < 0.7V Efficiency (VIN = 3.3V) vs. Output Current 100 1.0 Output Voltage (VIN = 5.0V) vs. Output Current 6.0 2.3 0.5 0.5 OUTPUT CURRENT (A) VFB < 0.7V OUTPUT CURRENT (A) EFFICIENCY (%) 1.5 VOUT = 1.8V 900 0 1.0 VIN = 3.3V 950 60 0.5 Output Voltage (VIN = 3.3V) vs. Output Current 4.3 1000 0.0 -0.20% VIN = 3.3V OUTPUT VOLTAGE (V) SWITCHING FREQUENCY (kHz) 1050 0.00% OUTPUT CURRENT (A) Switching Frequency vs. Output Current 1100 0.20% -0.40% 0.0 2 OUTPUT VOLTAGE (V) 0 VOUT = 1.8V 0.40% VOUT = 1.8V Case Temperature* (VIN = 3.3V) vs. Output Current 80 DIE TEMPERATURE (C) EFFICIENCY (%) 90 0.60% LINE REGULATION (%) 100 Line Regulation vs. Output Current 60 40 VIN = 3.3V 20 VOUT = 1.8V 0 0.12 0.0 0.00 0.5 1.0 1.5 2.0 OUTPUT CURRENT (A) 0 0.4 0.8 1.2 1.6 2 OUTPUT CURRENT (A) August 2011 8 M9999-082511-A Micrel, Inc. MIC22205 Typical Characteristics (Continued) Efficiency (VIN = 5V) vs. Output Current 100 0.72 95 80 80 75 70 65 POWER DISSIPATION (W) 3.3V 2.5V 1.8V 1.5V 1.2V 1.0V 0.9V 0.8V 0.7V 85 VIN = 5V 60 55 50 0 0.6 1.2 1.8 2.4 OUTPUT CURRENT (A) 3 0.6 DIE TEMPERATURE (C) Curves Top to Bottom 90 EFFICIENCY (%) Case Temperature* (VIN = 5.0V) vs. Output Current IC Power Dissipation (VIN = 5.0V) vs. Output Current 3.3V 2.5V 1.8V 1.5V 1.2V 1.0V 0.9V 0.8V 0.7V 0.48 0.36 0.24 60 40 VIN = 5V 20 VOUT = 1.8V 0.12 0 0 0.0 0 0.4 0.8 1.2 1.6 2 0.5 1.0 1.5 2.0 OUTPUT CURRENT (A) OUTPUT CURRENT (A) Die Temperature* : The temperature measurement was taken at the hottest point on the MIC22205 case and mounted on a fivesquare inch PCB (see Thermal Measurements section). Actual results will depend upon the size of the PCB, ambient temperature, and proximity to other heat-emitting components. August 2011 9 M9999-082511-A Micrel, Inc. MIC22205 Functional Characteristics August 2011 10 M9999-082511-A Micrel, Inc. MIC22205 Functional Characteristics (Continued) August 2011 11 M9999-082511-A Micrel, Inc. MIC22205 Functional Characteristics (Continued) August 2011 12 M9999-082511-A Micrel, Inc. MIC22205 Functional Diagram Figure 1. MIC22205 Functional Diagram August 2011 13 M9999-082511-A Micrel, Inc. MIC22205 Application Information Inductor Selection Inductor selection will be determined by the following (not in order of importance): The MIC22205 is a 2A, synchronous voltage mode, PWM step down regulator IC with a programmable frequency range from 300kHz to 4MHz. Other features include tracking and sequencing control for controlling multiple output power systems and power good (PG). By controlling the ratio of the on-to-off time, or duty cycle, a regulated DC output voltage is achieved. As load or supply voltage changes, so does the duty cycle to maintain a constant output voltage. In cases where the input supply runs into a dropout condition, the MIC22205 will run at 100% duty cycle. The internal MOSFETs include a high-side P-channel MOSFET from the input supply to the switch pin, and an N-channel MOSFET from the switch pin to ground. Since the low-side N-channel MOSFET provides the current during the off cycle, a very low amount of power is dissipated during the off period. The PWM control technique also provides adjustable fixed-frequency operation. By maintaining a constant switching frequency, predictable fundamental and harmonic frequencies are achieved. Other methods of regulation, such as burst and skip modes, have frequency spectrums that change with load that can interfere with sensitive communication equipment. Inductance * Rated current value * Size requirements * DC resistance (DCR) The MIC22205 is designed for use with a 0.47H to 4.7H inductor. Maximum current ratings of the inductor are generally given using two methods: permissible DC current and saturation current. Permissible DC current can be rated either for a 40C temperature rise, or a 10% loss in inductance. Ensure the inductor selected can handle the maximum operating current. When saturation current is specified, make sure that there is enough margin so the peak current will not saturate the inductor. The ripple current can add as much as 1.2A to the output current level. Choose an RMS rating that is equal to or greater than the current limit of the MIC22205 to prevent overheating in a fault condition. For best electrical performance, place the inductor very close to the SW nodes of the IC. The heat of the inductor is somewhat coupled to the IC, so it offers some level of protection if the inductor gets too hot (In such cases IC case temperature is not a true indication of IC dissipation). It is important to test all operating limits before settling on the final inductor choice. The size requirements refer to the area and height necessary to fit a particular design. Please refer to the inductor dimensions on the manufacturer's datasheet. DC resistance is also important. While DCR is inversely proportional to size, DCR increase can represent a significant efficiency loss. Refer to the "Efficiency Considerations" section below for a more detailed description. Component Selection Input Capacitor A 10F X5R or X7R dielectrics ceramic capacitor is recommended on each of the PVIN pins for bypassing. A Y5V dielectric capacitor should not be used. Aside from losing most of their capacitance over temperature, they also become resistive at high frequencies. This reduces their ability to filter out high-frequency noise. Output Capacitor The MIC22205 was designed specifically for use with ceramic output capacitors. The output capacitor can be increased from 47F to a higher value to improve transient performance. The MIC22205 operates in voltage mode, so the control loop relies on the inductor and output capacitor for compensation. For this reason, do not use excessively large output capacitors. The output capacitor requires either an X7R or X5R dielectric. Y5V and Z5U dielectric capacitors, aside from the undesirable effect of a wide variation in capacitance over temperature, become resistive at high frequencies. Using Y5V or Z5U capacitors can cause instability in the MIC22205. August 2011 * Efficiency Considerations Efficiency is defined as the amount of useful output power, divided by the amount of power consumed. V xI Efficiency % = OUT OUT V IN x IIN 14 x 100 M9999-082511-A Micrel, Inc. MIC22205 Maintaining high efficiency serves two purposes. First, it decreases power dissipation in the power supply, which reduces the need for heat sinks and thermal design considerations; also, it decreases the consumption of current for battery-powered applications. Reduced current demand from a battery increases the device's operating time, which is critical in hand-held devices. There are mainly two loss terms in switching converters: static losses and switching losses. Static losses are the power losses due to VI or I2R. For example, power is dissipated in the high side switch during the on cycle. Power loss is equal to the high-side MOSFET RDS(ON) multiplied by the RMS switch current squared (ISW2). During the off-cycle, the low-side N-channel MOSFET conducts, which also dissipates power. Similarly, the inductor's DCR and capacitor's ESR also contribute to I2R losses. A device's operating current also reduces efficiency by the product of the quiescent (operating) current and the supply voltage. The current required to drive the gates on and off at a constant 1MHz frequency, and the switching transitions make up the switching losses. Figure 2 illustrates a typical efficiency curve. From 0A to 0.2A, efficiency losses are dominated by quiescent current losses, gate drive, transition, and core losses. In this case, lower supply voltages yield greater efficiency because they require less current to drive the MOSFETs, and have reduced input power consumption. From 0.5A to 2A, efficiency loss is dominated by MOSFET RDS(ON) and inductor DC losses. Higher input supply voltages will increase the gate-to-source voltage on the internal MOSFETs, thereby reducing the internal RDS(ON). This improves efficiency by decreasing DC losses in the device. All but the inductor losses are inherent to the device. In this case, inductor selection is critical for efficiency calculations. As the inductors are reduced in size, the DC resistance (DCR) can become quite significant. The DCR losses can be calculated as follows: LPD = IOUT2 x DCR From that, the loss in efficiency due to inductor resistance can be calculated as follows: VOUT x IOUT Efficiency Loss = 1- (VOUT x IOUT ) + L PD Efficiency loss due to DCR is minimal at light loads, and gains significance as the load is increased. Inductor selection becomes a trade-off between efficiency and size in this case. Alternatively, under lighter loads, the ripple current due to the inductance becomes a significant factor in losses. When light load efficiencies become more critical, a larger inductor value may be desired. Larger inductances reduce the peak-to-peak inductor ripple current, which minimize losses. Efficiency (VIN = 5V) vs. Output Current 100 3.3V 95 EFFICIENCY (%) 90 85 1.8V 80 75 Compensation The MIC22205 has a combination of internal and external stability compensation to simplify the circuit for small, high efficiency designs. In such designs, voltage mode conversion is often the optimum solution. Voltage mode is achieved by creating an internal ramp signal, and using the output of the error amplifier to modulate the pulse width of the switch node, thereby maintaining output voltage regulation. With a typical gain bandwidth of 100kHz-200kHz, the MIC22205 is capable of extremely fast transient response. 70 65 V IN = 5V 60 55 50 0 0.5 1 1.5 2 OUTPUT CURRENT (A) Figure 2. Efficiency Curve August 2011 x 100 15 M9999-082511-A Micrel, Inc. MIC22205 The MIC22205 is designed to be stable with a typical application using a 1H inductor and a 47F ceramic (X5R) output capacitor. These values can be varied, depending on the size, cost, and efficiency, and still 1 keep the LC natural frequency 2x x L xC where VREF is 0.7V and VOUT is the desired output voltage. A 10k or lower resistor value from the output to the feedback (R1) is recommended, since large feedback resistor values increase the impedance at the feedback pin, making the feedback node more susceptible to noise pick-up. A small capacitor (50pF - 100pF) across the lower resistor can reduce noise pickup by providing a low impedance path to ground. less than 26 kHz to ensure stability. The minimum recommended inductor value is 0.47H and minimum recommended output capacitor value is 22F. The trade-off with changing these values is that with a larger inductor, there is a reduced peak-to-peak current, which yields a greater efficiency at lighter loads. A larger output capacitor will improve transient response by providing a larger hold-up reservoir of energy to the output. The integration of one pole-zero pair within the control loop greatly simplifies compensation. The optimum values for CCOMP (in series with a 20k resistor) are shown in Table 1: CAE LE 22F 47F 47F 100F 100F 470F 0* 10pF 22pF 33pF 0.47H 1H 0 15pF 15 22pF 33pF 2.2H 15 33pF 33 47pF 100 220pF Enable/Delay (EN/DLY) Pin Enable/Delay (EN/DLY) sources 1A out of the IC to allow a startup delay to be implemented. The delay time is the time it takes 1A to charge CEN/DLY to 1.25V. Therefore: t EN/DLY = * VOUT > 1.2V, VOUT > 1V CF Capacitor 56pF 68pF 82pF 100pF 150pF 180pF 220pF 270pF 330pF 390pF 470pF Note: Compensation values for various output voltages and inductor values refer to Table 3. Table 1. Compensation Capacitor Selection Feedback The MIC22205 provides a feedback pin to adjust the output voltage to the desired level. This pin connects internally to an error amplifier. The error amplifier then compares the voltage at the feedback to the internal 0.7V reference voltage, and adjusts the output voltage to maintain regulation. The resistor divider network for a desired VOUT is given by: August 2011 1x 10 - 6 CF Capacitor Adding a capacitor to this pin can adjust the switching frequency from 800kHz to 4MHz. CF sources 400A out of the IC to charge the CF capacitor in order to set up the switching frequency. The switch period is the time it takes 400A to charge CF to 1.0V. Therefore: R2 = 1.24 x C EN/DLY Frequency 4.4MHz 4MHz 3.4MHz 2.8MHz 2.1MHz 1.7MHz 1.4MHz 1.2MHz 1.1MHz 1.05MHz 1MHz Table 2. CF vs. Frequency It is necessary to connect the CF capacitor very close between the CF pin and signal ground. R1 V OUT - 1 V REF 16 M9999-082511-A Micrel, Inc. MIC22205 The maximum CRC value is calculated as follows: 300kHz to 800kHz Operation The frequency range can be lowered by adding an additional resistor (RCF) in parallel with the CF capacitor. This reduces the amount of current used to charge the capacitor, which reduces the frequency. The following equation can be used to for frequencies between 800kHz to 300kHz: CRC < Pre-Bias Start-Up The MIC22205 is designed for safe start-up into a prebiased output. This prevents large negative inductor currents and excessive output voltage oscillations. The MIC22205 starts with the low-side MOSFET turned off, preventing reverse inductor current flow. The synchronous MOSFET stays off until the Power Good (PG) goes high after the VFB is above 90 percent of VREF. A pre-bias condition can occur if the input is turned off, and then immediately turned back on before the output capacitor is discharged to ground. It is also possible that the output of the MIC22205 could be pulled up or prebiased through parasitic conduction paths from one supply rail to another in multiple voltage (VOUT) level ICs such as a FPGA. Figure 3 shows a normal start-up waveform. A 1A current source charges the soft-start capacitor CRC. The CRC capacitor forces the VRC voltage to come up slowly (VRC trace), which provides a soft-start ramp. This ramp is used to control the internal reference (VREF). The error amplifier forces the output voltage to follow the VREF ramp from zero to the final value. 1.0V =t - RCF xCCF xln1 + 400 A x RCF RCF > 2.9K RC Pin (Soft-Start) The RC pin provides a trimmed 1A current source/sink for accurate ramp-up (soft-start). This allows the MIC22205 to be used in systems that require voltage tracking or ratio-metric voltage tracking at startup. There are two ways of using the RC pin: 1. Externally driven from a voltage source 2. Externally attached capacitor sets output rampup/down rate In the first case, driving RC with a voltage from 0V to VREF will program the output voltage between 0 and 100% of the nominal set voltage, as shown in Figure 3. In the second case, the external capacitor sets the rampup and ramp-down time of the output voltage. The time is given by: t RAMP = 0.7 x C RC 1x 10 - 6 where tRAMP is the time from 0 to 100% nominal output voltage. During start-up, a light load condition (IOUT < 1.25A) can lead to negative inductor current. Under these conditions, the maximum ramp-up time should not exceed the critical ramp-up time period. This will keep the regulator in continuous mode operation when VFB reaches 90% of reference voltage. Beyond the critical ramp-up time, the regulator is in discontinuous mode, which leads to prolonged Nchannel MOSFET conduction, which in turn causes negative inductor current. August 2011 2.86 * COUT * L * FSW * 10 -6 _ VOUT 1 VIN Figure 3. EN Turn-On Time - Normal Start-Up 17 M9999-082511-A Micrel, Inc. MIC22205 If the output is pre-biased to a voltage above the expected value, as shown in Figure 4, then neither MOSFET will turn on until the ramp control voltage (VRC) is above the reference voltage (VREF). Then, the highside MOSFET starts switching, forcing the output to follow the VRC ramp. Once the feedback voltage is above 90 percent of the reference voltage, the low-side MOSFET will begin switching. If the output voltage falls slower than the VRC voltage, then the both MOSFETs will be off and the output will decay to zero as shown in the VOUT trace in Figure 6 with both MOSFETs off, any resistive load connected to the output will help pull down the output voltage. This will occur at a rate determined by the resistance of the load and the output capacitance. Figure 6. EN Turn-Off - 200mA Load Figure 4. EN Turn-On at 1V Pre-Bias Current Limit The MIC22205 uses a two-stage technique to protect against overload. The first stage is to limit the current in the P-channel switch; the second is over temperature shutdown. Current is limited by measuring the current through the high-side MOSFET during its power stroke and immediately switching off the driver when the preset limit is exceeded. The circuit in Figure 7 describes the operation of the current limit circuit. Since the actual RDSON of the Pchannel MOSFET varies from part to part and with changes in temperature and input voltage, simple IR voltage detection is not employed. Instead, a smaller copy of the Power MOSFET (Reference FET) is fed with a constant current which is a directly proportional to the factory set current limit. This sets the current limit as a current ratio and thus, is not dependant upon the RDSON value. Current limit is set to nominal value. Variations in the scale factor K between the power PFET and the reference PFET used to generate the limit threshold account for a relatively small inaccuracy. When the MIC22205 is turned off, the low-side MOSFET will be disabled, and the output voltage will decay to zero. During this time, the ramp control voltage (VRC) will still control the output voltage fall-time with the high-side MOSFET, if the output voltage falls faster than the VRC voltage. Figure 5 shows this operating condition. Here, a 2A load pulls the output down fast enough to force the high-side MOSFET on (VSW trace). Figure 5. EN Turn-OFF - 2A Load August 2011 18 M9999-082511-A Micrel, Inc. MIC22205 To calculate the junction temperature for a 50C ambient: TJ = TAMB+PDISS . RJA TJ = 50 + (0.72 x 40) TJ = 78.8C This is below the maximum of 125C. Thermal Measurements Measuring the IC's case temperature is recommended to ensure it is within its operating limits. The most common mistake made is to use the standard thermal couple that comes with a thermal meter. This thermal couple wire gauge is large, typically 22-gauge, and behaves like a heat-sink, resulting in a lower case measurement. Two better methods of temperature measurement are using a smaller thermal couple wire or an infrared thermometer. If a thermal couple wire is used, it must be constructed of 36-gauge wire or higher (smaller wire size) to minimize the wire heat-sinking effect. In addition, the thermal couple tip must be covered in either thermal grease or thermal glue to ensure the thermal couple junction makes good contact with the case of the IC. Omega brand thermal couple (5SC-TT-K-36-36) is adequate for most applications. Whenever possible, an infrared thermometer is recommended. The measurement spot size of most infrared thermometers is too large for an accurate reading on a small form factor ICs. However, an IR thermometer from Optris has a 1mm spot size, which makes it a good choice for measuring the hottest point on the case. Using a stand makes it easier to hold the beam on the IC for long periods of time. Figure 7. Current-Limit Detail Thermal Considerations The MIC22205 is packaged in a MLF(R) 3mm x 3mm - a package that has excellent thermal-performance equaling that of larger TSSOP packages. This maximizes heat transfer from the junction to the exposed pad (ePad), which connects to the ground plane. The size of the ground plane attached to the exposed pad determines the overall thermal resistance from the junction to the ambient air surrounding the printed circuit board. The junction temperature for a given ambient temperature can be calculated using: TJ = TAMB + PDISS x RJA where: * * PDISS is the power dissipated within the MLF(R) package and is at 2A load. RJA is a combination of junction-to-case thermal resistance (RJC) and Case-to-Ambient thermal resistance (RCA), since thermal resistance of the solder connection from the ePAD to the PCB is negligible; RCA is the thermal resistance of the ground plane-to-ambient, so RJA = RJC + RCA. Sequencing and Tracking There are four variations of sequencing and tracking that are easily implemented using the MIC22205. The two sequencing variations are Delayed and Windowed. The two tracking variants are Normal and Ratio Metric. The following diagrams illustrate methods for connecting two MIC22205's to achieve these requirements. TAMB is the operating ambient temperature. Example: The Evaluation board has two copper planes contributing to an RJA of approximately 40C/W. The worst case RJC of the MLF 3mm x 3mm is 28.7C/W. RJA = RJC + RCA RJA = 28.7 + 11.3 = 40C/W August 2011 19 M9999-082511-A Micrel, Inc. MIC22205 Window Sequencing: Delayed Sequencing: MIC22205 VIN 5.0V 10F PVIN SVIN PGND 10k POR1 EN1 VOUT1 1.8V/2A 47F EP SGND POR 3.3nF PVIN SVIN PGND POR EN2 EN/DLY RC CF 10nF 47F EP SGND R3 7.14k 10F 10k FB POR2 R4 10k PVIN SVIN PGND POR EN2 EN/DLY RC 47pF 220pF EP SGND CF 20k 1.0nF 3.3nF R1 16k FB R2 10k COMP 47pF 20k MIC22205 VOUT2 1.2V/2A VOUT1 1.8V/2A 47F 220pF 1.0H SW 1.0H SW POR EN1 20k COMP RC CF PVIN SVIN PGND POR1 EN/DLY 3.3nF 10F 47pF MIC22205 POR2 R1 16k R2 10k COMP 220pF 10F VIN 5.0V FB EN/DLY RC CF MIC22205 1.0H SW 1.0H VOUT2 1.2V/2A SW 47F EP SGND R3 7.14k FB R4 10k COMP 47pF 220pF 20k 4.0ms/Div 4.0ms/Div August 2011 20 M9999-082511-A Micrel, Inc. MIC22205 Normal Tracking: Ratio Metric Tracking: MIC22205 VIN 5.0V 10F 47.5k PVIN SVIN PGND POR1 EP SGND 3.3nF 47pF 20k MIC22205 PVIN SVIN PGND EN2 R2 10k COMP 220pF 10F R1 16k FB EN/DLY RC CF POR2 VOUT1 1.8V/2A 47F POR EN1 1.0H SW POR 1.0H VOUT2 1.2V/2A SW 47F EP SGND FB EN/DLY RC CF R3 7.14k R4 10k COMP 47pF 220pF 20k 4.0ms/div 4.0ms/Div August 2011 21 M9999-082511-A Micrel, Inc. MIC22205 VIN = 5V VOUT L COUT CCOMP RCOMP CFF RFF CFB RFB 1.1V 3.3H 2 x 47F 100pF 5k N.U. 4.7k 100pF 8.2k 1.3V 1.5H 2 x 47F 100pF 5k 1nF 4.7k 100pF 5.49k 1.8V 2.2H 2 x 47F 100pF 5k 1nF 4.7k 100pF 3.0k 4.2V 1.5H 2 x 47F 100pF 20k 1nF 4.7k 100pF 953 Table 3. Compensation Selection Figure 8. Schematic Reference August 2011 22 M9999-082511-A Micrel, Inc. MIC22205 Inductor PCB Layout Guidelines IMPORTANT: To minimize EMI and output noise, follow these layout recommendations. PCB layout is critical to achieving reliable, stable and efficient performance. A ground plane is required to control EMI, and to minimize the inductance in power, signal, and return paths. Follow these guidelines to ensure proper operation of the MIC22205 converter: * Keep the inductor connection to the switch node (SW) short. * Do not route any digital lines underneath or close to the inductor. * Keep the switch node (SW) away from the feedback (FB) pin. * To minimize noise, place a ground plane underneath the inductor. * The inductor can be placed on the opposite side of the PCB with respect to the IC. It does not matter whether the IC or inductor is on the top or bottom, as long as there is enough air flow to keep the power components within their temperature limits. The input and output capacitors must be placed on the same side of the board as the IC. IC * The 2.2F ceramic capacitor, which is connected to the SVIN pin, must be located right at the IC. The SVIN pin is noise sensitive, so placement of the capacitor is critical. Use wide traces to connect to the SVIN and SGND pins. * The signal ground pin (SGND) must be connected directly to the ground planes. Do not route the SGND pin to the PGND pad on the top layer. * Place the IC close to the point of load (POL). * Use fat traces to route the input and output power lines. * Signal and power grounds should be kept separate and connected at only one location. Output Capacitor Input Capacitor * A 10F X5R or X7R dielectrics ceramic capacitor is recommended on the PVIN pin for bypassing. * Place the input capacitors on the same side of the board and as close to the IC as possible. * Keep both the PVIN pin and PGND connections short. * Place several vias to the ground plane close to the input capacitor ground terminal. * Use either X7R or X5R dielectric input capacitors. Do not use Y5V or Z5U type capacitors. * Do not replace the ceramic input capacitor with any other type of capacitor. Any type of capacitor can be placed in parallel with the input capacitor. * If a Tantalum input capacitor is placed in parallel with the input capacitor, it must be recommended for switching regulator applications, and the operating voltage must be de-rated by 50%. * In "Hot-Plug" applications, a Tantalum or Electrolytic bypass capacitor must be used to limit the overvoltage spike seen on the input supply when power is suddenly applied. August 2011 * Use a wide trace to connect the output capacitor ground terminal to the input capacitor ground terminal. * Phase margin will change as the output capacitor value and ESR changes. Contact the factory if the output capacitor is different from what is shown in the BOM. * The feedback divider network must be place close to the IC with the bottom of R2 connected to SGND. * The feedback trace should be separate from the power trace, and connected as close as possible to the output capacitor. Sensing a long high-current load trace can degrade the DC load regulation. RC Snubber * 23 Place the RC snubber on either side of the board, and as close to the SW pin as possible. M9999-082511-A Micrel, Inc. MIC22205 Evaluation Board Schematic Bill of Materials Item Part Number C2012X5R0J106K C1 C2 C3 GRM2196R60J106K Manufacturer Murata(2) Qty. Capacitor, 10F, 6.3V, X5R, Size 0805 1 Capacitor, 2.2F, 6.3V, X5R, Size 0603 1 (3) 08056D106KAT2A AVX C1608X5R0J225M TDK(1) GRM188R60J225M Murata(2) (3) 06036D225MAT2A AVX C1608X7RH471K TDK(1) GRM188R71H471KA01D Description TDK(1) Murata(2) Capacitor, 470pF, 50V, X7R, Size 0603 (3) 06035C471KAT2A AVX C1608C0G1H470J TDK(1) C4 C5 C6 C7, C8 GQM1885C1H470JB01D AVX C1608C0G1H221J TDK(1) GRM1885C1H221JA01D Murata(2) AVX C1608C0G1H102J TDK(1) (2) Murata AVX 1 Capacitor, 220pF, 50V, NPO, Size 0603 1 Capacitor, 1nF, 50V, NPO, Size 0603 2 (3) 06035A221JAT2A GRM1885C1H102JA01D Capacitor, 47pF, 50V, NPO, Size 0603 (3) 06035A470JAT2A 06035A102KAT2A August 2011 Murata(2) (3) 24 M9999-082511-A Micrel, Inc. MIC22205 Bill of Materials (Continued) Item Part Number C3216X5R0J476M C9, C10 C11 C12 L1 GRM31CR60J476ME19L Manufacturer TDK Murata(2) 1206D476MAT2A AVX (3) C1608C0G1H101J TDK GRM1885C1H101JA01D Qty. Capacitor, 47F, 6.3V, X5R, Size 1206 2 Capacitor, 100pF, 50V, NPO Size 0603 1 470F, 10V, Electrolytic, 8x10 case 1 (1) Murata(2) (3) 06035A101JAT2A AVX B41125A3477M Epcos(4) IHLP1616BZER1R0M11 Description (1) Vishay (5) Inductor , 1H, 5A 1 (3) R1 CRCW06031602FKEA AVX Resistor, 16K, 1%, Size 0603 1 R2, R3 CRCW06031002FKEA AVX (3) Resistor, 10K, 1%, Size 0603 2 CRCW060320K0FKEA AVX (3) Resistor, 20K, 1%, Size 0603 1 AVX (3) Resistor, 2.2, 1%, Size 0603 1 AVX (3) R4 R5 CRCW06032R20FKEA R6 CRCW060349R9FKEA U1 MIC22205YML Micrel(6) Resistor, 49.9, 1%, Size 0603 1 Integrated 2A Synchronous Buck Regulator 1 Notes: 1. TDK: www.tdk.com. 2. Murata: www.murata.com. 3. AVX: www.avx.com. 4. Epcos: www.epcos.com. 5. Vishay: www.vishay.com. 6. Micrel, Inc.: www.micrel.com. August 2011 25 M9999-082511-A Micrel, Inc. MIC22205 PCB Layout Recommendations MIC22205 Evaluation Board Top Layer MIC22205 Evaluation Board Bottom Layer August 2011 26 M9999-082511-A Micrel, Inc. MIC22205 PCB Layout Recommendations (Continued) MIC22205 Evaluation Board Top Silk MIC22205 Evaluation Board Bottom Silk August 2011 27 M9999-082511-A Micrel, Inc. MIC22205 Package Information 12-Pin 3mm x 3mm MLF(R) (ML) August 2011 28 M9999-082511-A Micrel, Inc. MIC22205 Recommended Landing Pattern MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 USA TEL +1 (408) 944-0800 FAX +1 (408) 474-1000 WEB http://www.micrel.com Micrel makes no representations or warranties with respect to the accuracy or completeness of the information furnished in this data sheet. This information is not intended as a warranty and Micrel does not assume responsibility for its use. Micrel reserves the right to change circuitry, specifications and descriptions at any time without notice. No license, whether express, implied, arising by estoppel or otherwise, to any intellectual property rights is granted by this document. Except as provided in Micrel's terms and conditions of sale for such products, Micrel assumes no liability whatsoever, and Micrel disclaims any express or implied warranty relating to the sale and/or use of Micrel products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright or other intellectual property right. Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser's use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser's own risk and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale. (c) 2011 Micrel, Incorporated. August 2011 29 M9999-082511-A