R474R382004A1MR474R382040A1M - KEMET Electronics Corporation

09/2008

159

Ø d ±0.05 p ≤15 22.5 ≤ p ≤ 27.5 p = 37.5

0.6 or 0.8* 0.8 1.0

*See size table.

All dimensions are in mm.

GENERAL TECHNICAL DATA

Dielectric: polypropylene lm - 2 sections.

Plates: metal layer deposited by evaporation under vacuum.

Winding: non-inductive type.

Leads: tinned wire.

Protection: plastic case, thermosetting resin lled.

Box material is solvent resistant and ame retardant according to

UL94 V0.

Marking: Manufacturer’s logo, series, capacitance, tolerance,

rated voltage, capacitor class, dielectric code, climatic category,

passive ammability category, manufacturing date code, approvals,

manufacturing plant.

Climatic category: 40/110/56 IEC 60068-1

Operating temperature range: -40 to +110°C

Related documents: IEC 60384-14; EN 60384-14.

ELECTRICAL CHARACTERISTICS

Rated voltage (VR): 440Vac / 1000Vdc; 50/60Hz

Capacitance range: 4700pF to 2.2µF

Capacitance values: E6 series (IEC 60063 Norm).

Capacitance tolerances (measured at 1 kHz):

±10% (K); ±20% (M).

Tolerance ±5% (J) available

upon request.

Dissipation factor (DF):

tgδ x 10-4 at +25°C ±5°C: ≤10 (6)* at 1kHz *

Typical value

Insulation resistance:

Test conditions

Temperature: +25°C±5°C

Voltage charge time: 1 min

Voltage charge: 100 Vdc

Performance

≥1x105 MΩ for C≤0.33µF

≥30000 s for C>0.33µF

Test voltage between terminations (on all pieces):

1700Vac for 1 s + 2700Vdc for 1 s at +25°C±5°C

R.47

X2 CLASS (IEC 60384-14) - MKP Series

METALLIZED POLYPROPYLENE FILM CAPACITOR

SELF-HEALING PRoPERTIES

Typical applications: interference suppression and

«across-the-line» applications. Suitable for use in situations

where failure of the capacitor would not lead to danger of

electric shock.

PRoDUCT CoDE: R47

TEST METHOD AND PERFORMANCE

Damp heat, steady state:

Test conditions 1st

Temperature: +40°C ± 2°C

Relative humidity (RH): 93% ±2%

Test duration: 56 days

Test conditions 2nd

Temperature: +60°C ± 2°C

Relative humidity (RH): 95% ±2%

Test duration: 500 hours

Performance

Dielectric strength: no dielectric breakdown or

ashover at 4.3 x VR (d.c.)/1 min

Capacitance change |∆C/C|: ≤5%

Insulation resistance: ≥50% of initial limit.

Endurance:

Test conditions

Temperature: +110°C ± 2°C

Test duration: 1000 h

Voltage applied: 1.25 x VR +1000Vac 0.1 s/h

Performance

Dielectric strength: no dielectric breakdown or

ashover at 4.3 x VR (d.c.)/1 min

Capacitance change |∆C/C|: ≤10%

Insulation resistance: ≥50% of initial limit.

Resistance to soldering heat:

Test conditions

Solder bath temperature: +260°C ± 5°C

Dipping time (with heat screen):10 s ± 1 s

Performance

Capacitance change |∆C/C|: ≤2%

Pitch Box thickness (B) Maximum dimensions (mm)

(mm) (mm) B max H max L max

10.0 All B +0.2 H +0.1 L +0.2

15.0 <7.5 B +0.2 H +0.1 L +0.3

15.0 ≥7.5 B +0.2 H +0.1 L +0.5

22.5 All B +0.2 H +0.1 L +0.3

27.5 All B +0.2 H +0.1 L +0.3

37.5 All B +0.3 H +0.1 L +0.3

single sided metallized

polypropylene lm

2 sections

Winding scheme

Loose Taped

Fig.1 Fig.2

09/2008 160

R.47

X2 CLASS (IEC60384-14) - MKP Series

METALLIZED POLYPROPYLENE FILM CAPACITOR

SELF-HEALING PRoPERTIES

PRoDUCT CoDE: R47

APPROVALS

Approved according to IEC 60384-14

According to IEC 60065.

(*) ENEC mark has replaced all the following European

National marks:

Rated Cap. 440 Vac / 1000 Vdc

Std dimensions Ø d Max

dv/dt at

420Vdc

Part Number

B H L p (V/ µs)

4700 pF 4.0 9.0 13.0 10.0 0.6 750 R474F 1470 - - 01 -

6800 pF 5.0 11.0 13.0 10.0 0.6 750 R474F 1680 - - 01 -

8200 pF 6.0 12.0 13.0 10.0 0.6 750 R474F 1820 - - 01 -

0.010 µF 6.0 12.0 13.0 10.0 0.6 750 R474F 2100 - - 01 -

0.010 µF 5.0 11.0 18.0 15.0 0.6 600 R474I 2100 - - 01 -

0.012 µF 5.0 11.0 18.0 15.0 0.6 600 R474I 2120 - - 01 -

0.015 µF 5.0 11.0 18.0 15.0 0.6 600 R474I 2150 - - 01 -

0.018 µF 5.0 11.0 18.0 15.0 0.6 600 R474I 2180 - - 01 -

0.022 µF 6.0 12.0 18.0 15.0 0.6 600 R474I 2220 - - 01 -

0.027 µF 6.0 12.0 18.0 15.0 0.6 600 R474I 2270 - - 01 -

0.033 µF 6.0 12.0 18.0 15.0 0.6 600 R474I 2330 - - 01 -

0.039 µF 7.5 13.5 18.0 15.0 0.6 600 R474I 2390 - - 01 -

0.047 µF 7.5 13.5 18.0 15.0 0.6 600 R474I 2470 - - 01 -

0.047 µF 6.0 17.5 18.0 15.0 0.6 600 R474I 2470 - - 02 -

0.047 µF 9.0 12.5 18.0 15.0 0.6 600 R474I 2470 - - 03 -

0.056 µF 8.5 14.5 18.0 15.0 0.6 600 R474I 2560 - - 01 -

0.068 µF 10.0 16.0 18.0 15.0 0.8 600 R474I 2680 - - 01 -

0.068 µF 7.5 18.5 18.0 15.0 0.8 600 R474I 2680 - - 02 -

0.068 µF 13.0 12.0 18.0 15.0 0.8 600 R474I 2680 - - 03 -

0.082 µF 10.0 16.0 18.0 15.0 0.8 600 R474I 2820 - - 01 -

0.10 µF 11.0 19.0 18.0 15.0 0.8 600 R474I 3100 - - 01 -

0.047 µF 6.0 15.0 26.5 22.5 0.8 300 R474N 2470 - - 01 -

0.047 µF 6.5 13.5 26.5 22.5 0.8 300 R474N 2470 - - 02 -

0.068 µF 6.0 15.0 26.5 22.5 0.8 300 R474N 2680 - - 01 -

0.10 µF 7.0 16.0 26.5 22.5 0.8 300 R474N 3100 - - 01 -

0.12 µF 8.5 17.0 26.5 22.5 0.8 300 R474N 3120 - - 01 -

0.15 µF 10.0 18.5 26.5 22.5 0.8 300 R474N 3150 - - 01 -

0.18 µF 10.0 18.5 26.5 22.5 0.8 300 R474N 3180 - - 01 -

0.22 µF 11.0 20.0 26.5 22.5 0.8 300 R474N 3220 - - 01 -

0.27 µF 13.0 22.0 26.5 22.5 0.8 300 R474N 3270 - - 01 -

0.33 µF 13.0 22.0 26.5 22.5 0.8 300 R474N 3330 - - 01 -

0.15 µF 9.0 17.0 32.0 27.5 0.8 225 R474R 3150 - - 01 -

0.18 µF 9.0 17.0 32.0 27.5 0.8 225 R474R 3180 - - 01 -

0.22 µF 9.0 17.0 32.0 27.5 0.8 225 R474R 3220 - - 01 -

0.27 µF 9.0 17.0 32.0 27.5 0.8 225 R474R 3270 - - 02 -

0.33 µF 11.0 20.0 32.0 27.5 0.8 225 R474R 3330 - - 02 -

0.39 µF 11.0 20.0 32.0 27.5 0.8 225 R474R 3390 - - 01 -

0.47 µF 13.0 22.0 32.0 27.5 0.8 225 R474R 3470 - - 01 -

0.56 µF 13.0 22.0 32.0 27.5 0.8 225 R474R 3560 - - 01 -

0.68 µF 14.0 28.0 32.0 27.5 0.8 225 R474R 3680 - - 01 -

0.82 µF 18.0 33.0 32.0 27.5 0.8 225 R474R 3820 - - 01 -

1.0 µF 18.0 33.0 32.0 27.5 0.8 225 R474R 4100 - - 01 -

1.2 µF 18.0 33.0 32.0 27.5 0.8 225 R474R 4120 - - 01 -

1.5 µF 22.0 37.0 32.0 27.5 0.8 225 R474R 4150 - - 01 -

0.47 µF 11.0 22.0 41.5 37.5 1.0 150 R474W 3470 - - 01 -

0.56 µF 11.0 22.0 41.5 37.5 1.0 150 R474W 3560 - - 01 -

0.68 µF 13.0 24.0 41.5 37.5 1.0 150 R474W 3680 - - 01 -

0.82 µF 16.0 28.5 41.5 37.5 1.0 150 R474W 3820 - - 01 -

1.0 µF 16.0 28.5 41.5 37.5 1.0 150 R474W 4100 - - 01 -

1.2 µF 19.0 32.0 41.5 37.5 1.0 150 R474W 4120 - - 01 -

1.5 µF 19.0 32.0 41.5 37.5 1.0 150 R474W 4150 - - 01 -

1.8 µF 20.0 40.0 41.5 37.5 1.0 150 R474W 4180 - - 01 -

2.2 µF 20.0 40.0 41.5 37.5 1.0 150 R474W 4220 - - 01 -

All dimensions are in mm

(*) ENEC

IEC 60384-14 Class X2 File No.

CA08.00101

UL 1414

up to 1µF, 85°C;

250Vac) Across-the-line File No. E97797

UL 1283 Electromagnetic

Interference

Filters File No. E85238

Table 1

Standard

packaging style Lead

length

(mm)

Taping style Ordering

code

(Digit 10 to 11)

(mm) Fig.

(No.) Pitch

(mm)

AMMo-PACK

AMMo-PACK 12.70

19.05 1

210.0/15.0

22.5 DQ

REEL Ø500mm

12.70

19.05 1

210.0/15.0

22.5/27.5 CK

Loose, short leads

Loose, long leads

04 +2

25 -1/+2

30 +5

Note: Ammo-pack is the preferred packaging for taped version.

Mechanical version and packaging (Table 1)

Tolerance: K (±10%); M (±20%)

09/2008

161

GENERAL TECHNICAL DATA

Dielectric: polypropylene lm - 2 sections.

Plates: metal layer deposited by evaporation under vacuum.

Winding: non-inductive type.

Leads: tinned wire.

Protection: plastic case, thermosetting resin lled.

Box material is solvent resistant and ame retardant according to

UL94 V0.

Marking: Manufacturer’s logo, series, capacitance, tolerance,

rated voltage, capacitor class, dielectric code, climatic category,

passive ammability category, manufacturing date code, approvals,

manufacturing plant.

Climatic category: 40/110/56 IEC 60068-1

Operating temperature range: -40 to +110°C

Related documents: IEC 60384-14; EN60384-14

ELECTRICAL CHARACTERISTICS

Rated voltage (VR): 440Vac / 1000Vdc; 50/60Hz

Capacitance range: 4700pF to 2.2µF

Capacitance values: E6 series (IEC 60063 Norm).

Capacitance tolerances (measured at 1 kHz):

±10% (K); ±20% (M);

Tolerance ±5% (J) available

upon request.

Dissipation factor (DF):

tgδ x 10-4 at +25°C ±5°C: ≤10 (6)* at 1kHz *

Typical value

Insulation resistance:

Test conditions

Temperature: +25°C±5°C

Voltage charge time: 1 min

Voltage charge: 100 Vdc

Performance

≥1x105 MΩ for C≤0.33µF

≥30000 s for C>0.33µF

Test voltage between terminations (on all pieces):

1700Vac for 1 s + 2700Vdc for 1 s at +25°C±5°C

R.47

X1 CLASS (IEC 60384-14) - MKP Series

METALLIZED POLYPROPYLENE FILM CAPACITOR

SELF-HEALING PRoPERTIES

Typical applications: interference suppression and «across-

the-line» applications. Suitable for use in situations where

failure of the capacitor would not lead to danger of electric

shock.

Class X1 shall be applied for PERMANENTLY CoNNECTED

APPARATUS.

Note: PERMANENTLY CONNECTED APPARATUS:

apparatus which is intended for connection to the mains

by a connection which cannot be loosened BY HAND.

BY HAND:

operation that does not require the use of any object

such a tool, coin, etc.

PRoDUCT CoDE: R47

Pitch Box thickness (B) Maximum dimensions (mm)

(mm) (mm) B max H max L max

10.0 All B +0.2 H +0.1 L +0.2

15.0 <7.5 B +0.2 H +0.1 L +0.3

15.0 ≥7.5 B +0.2 H +0.1 L +0.5

22.5 All B +0.2 H +0.1 L +0.3

27.5 All B +0.2 H +0.1 L +0.3

37.5 All B +0.3 H +0.1 L +0.3

TEST METHOD AND PERFORMANCE

Damp heat, steady state:

Test conditions 1st

Temperature: +40°C ± 2°C

Relative humidity (RH): 93% ±2%

Test duration: 56 days

Test conditions 2nd

Temperature: +60°C ± 2°C

Relative humidity (RH): 95% ±2%

Test duration: 500 hours

Performance

Dielectric strength: no dielectric breakdown or

ashover at 4.3 x VR (d.c.)/1 min

Capacitance change |∆C/C|: ≤5%

Insulation resistance: ≥50% of initial limit.

Endurance:

Test conditions

Temperature: +110°C ± 2°C

Test duration: 1000 h

Voltage applied: 1.25 x VR +1000Vac 0.1 s/h

Performance

Dielectric strength: no dielectric breakdown or

ashover at 4.3 x VR (d.c.)/1 min

Capacitance change |∆C/C|: ≤10%

Insulation resistance: ≥50% of initial limit.

Resistance to soldering heat:

Test conditions

Solder bath temperature: +260°C ± 5°C

Dipping time (with heat screen):10 s ± 1 s

Performance

Capacitance change |∆C/C|: ≤2%

Ø d ±0.05 p ≤15 22.5 ≤ p ≤ 27.5 p = 37.5

0.6 or 0.8* 0.8 1.0

*See size table.

All dimensions are in mm.

Loose Taped

Fig.1 Fig.2

Rated Cap. 440 Vac / 1000 Vdc

Std dimensions Ø d Max

dv/dt at

420Vdc

Part Number

B H L p (V/ µs)

4700 pF 4.0 9.0 13.0 10.0 0.6 750 R474F 1470 - - A1 -

6800 pF 5.0 11.0 13.0 10.0 0.6 750 R474F 1680 - - A1 -

8200 pF 6.0 12.0 13.0 10.0 0.6 750 R474F 1820 - - A1 -

0.010 µF 6.0 12.0 13.0 10.0 0.6 750 R474F 2100 - - A1 -

0.010 µF 5.0 11.0 18.0 15.0 0.6 600 R474I 2100 - - A1 -

0.012 µF 5.0 11.0 18.0 15.0 0.6 600 R474I 2120 - - A1 -

0.015 µF 5.0 11.0 18.0 15.0 0.6 600 R474I 2150 - - A1 -

0.018 µF 5.0 11.0 18.0 15.0 0.6 600 R474I 2180 - - A1 -

0.022 µF 6.0 12.0 18.0 15.0 0.6 600 R474I 2220 - - A1 -

0.027 µF 6.0 12.0 18.0 15.0 0.6 600 R474I 2270 - - A1 -

0.033 µF 6.0 12.0 18.0 15.0 0.6 600 R474I 2330 - - A1 -

0.039 µF 7.5 13.5 18.0 15.0 0.6 600 R474I 2390 - - A1 -

0.047 µF 7.5 13.5 18.0 15.0 0.6 600 R474I 2470 - - A1 -

0.047 µF 6.0 17.5 18.0 15.0 0.6 600 R474I 2470 - - A2 -

0.047 µF 9.0 12.5 18.0 15.0 0.6 600 R474I 2470 - - A3 -

0.056 µF 8.5 14.5 18.0 15.0 0.6 600 R474I 2560 - - A1 -

0.068 µF 10.0 16.0 18.0 15.0 0.8 600 R474I 2680 - - A1 -

0.068 µF 7.5 18.5 18.0 15.0 0.8 600 R474I 2680 - - A2 -

0.068 µF 13.0 12.0 18.0 15.0 0.8 600 R474I 2680 - - A3 -

0.082 µF 10.0 16.0 18.0 15.0 0.8 600 R474I 2820 - - A1 -

0.10 µF 11.0 19.0 18.0 15.0 0.8 600 R474I 3100 - - A1 -

0.047 µF 6.0 15.0 26.5 22.5 0.8 300 R474N 2470 - - A1 -

0.047 µF 6.5 13.5 26.5 22.5 0.8 300 R474N 2470 - - A2 -

0.068 µF 6.0 15.0 26.5 22.5 0.8 300 R474N 2680 - - A1 -

0.10 µF 7.0 16.0 26.5 22.5 0.8 300 R474N 3100 - - A1 -

0.12 µF 8.5 17.0 26.5 22.5 0.8 300 R474N 3120 - - A1 -

0.15 µF 10.0 18.5 26.5 22.5 0.8 300 R474N 3150 - - A1 -

0.18 µF 10.0 18.5 26.5 22.5 0.8 300 R474N 3180 - - A1 -

0.22 µF 11.0 20.0 26.5 22.5 0.8 300 R474N 3220 - - A1 -

0.27 µF 13.0 22.0 26.5 22.5 0.8 300 R474N 3270 - - A1 -

0.33 µF 13.0 22.0 26.5 22.5 0.8 300 R474N 3330 - - A1 -

0.15 µF 9.0 17.0 32.0 27.5 0.8 225 R474R 3150 - - A1 -

0.18 µF 9.0 17.0 32.0 27.5 0.8 225 R474R 3180 - - A1 -

0.22 µF 9.0 17.0 32.0 27.5 0.8 225 R474R 3220 - - A1 -

0.27 µF 9.0 17.0 32.0 27.5 0.8 225 R474R 3270 - - A2 -

0.33 µF 11.0 20.0 32.0 27.5 0.8 225 R474R 3330 - - A2 -

0.39 µF 11.0 20.0 32.0 27.5 0.8 225 R474R 3390 - - A1 -

0.47 µF 13.0 22.0 32.0 27.5 0.8 225 R474R 3470 - - A1 -

0.56 µF 13.0 22.0 32.0 27.5 0.8 225 R474R 3560 - - A1 -

0.68 µF 14.0 28.0 32.0 27.5 0.8 225 R474R 3680 - - A1 -

0.82 µF 18.0 33.0 32.0 27.5 0.8 225 R474R 3820 - - A1 -

1.0 µF 18.0 33.0 32.0 27.5 0.8 225 R474R 4100 - - A1 -

1.2 µF 18.0 33.0 32.0 27.5 0.8 225 R474R 4120 - - A1 -

1.5 µF 22.0 37.0 32.0 27.5 0.8 225 R474R 4150 - - A1 -

0.47 µF 11.0 22.0 41.5 37.5 1.0 150 R474W 3470 - - A1 -

0.56 µF 11.0 22.0 41.5 37.5 1.0 150 R474W 3560 - - A1 -

0.68 µF 13.0 24.0 41.5 37.5 1.0 150 R474W 3680 - - A1 -

0.82 µF 16.0 28.5 41.5 37.5 1.0 150 R474W 3820 - - A1 -

1.0 µF 16.0 28.5 41.5 37.5 1.0 150 R474W 4100 - - A1 -

1.2 µF 19.0 32.0 41.5 37.5 1.0 150 R474W 4120 - - A1 -

1.5 µF 19.0 32.0 41.5 37.5 1.0 150 R474W 4150 - - A1 -

1.8 µF 20.0 40.0 41.5 37.5 1.0 150 R474W 4180 - - A1 -

2.2 µF 20.0 40.0 41.5 37.5 1.0 150 R474W 4220 - - A1 -

Mechanical version and packaging (Table 1)

Tolerance: K (±10%); M (±20%)

All dimensions are in mm

R.47

X1 CLASS (IEC 60384-14) - MKP Series

METALLIZED POLYPROPYLENE FILM CAPACITOR

SELF-HEALING PRoPERTIES

PRoDUCT CoDE: R47

APPROVALS

(*) ENEC

IEC 60384-14 Class X1 File No.

CA08.00101

UL 1414

up to 1µF, 85°C;

250Vac) Across-the-line File No. E97797

UL 1283 Electromagnetic

Interference

Filters File No. E85238

Approved according to IEC 60384-14

According to IEC 60065.

(*) ENEC mark has replaced all the following European

National marks:

Table 1

Standard

packaging style Lead

length

(mm)

Taping style Ordering

code

(Digit 10 to 11)

(mm) Fig.

(No.) Pitch

(mm)

AMMo-PACK

AMMo-PACK 12.70

19.05 1

210.0/15.0

22.5 DQ

REEL Ø500mm

12.70

19.05 1

210.0/15.0

22.5/27.5 CK

Loose, short leads

Loose, long leads

04 +2

25 -1/+2

30 +5

Note: Ammo-pack is the preferred packaging for taped version.

single sided metallized

polypropylene lm

2 sections

Winding scheme

Statements of suitability for certain applications are based on our knowledge of typical operating conditions for such applications, but are not intended to constitute –

and we specifically disclaim – any warranty concerning suitability for a specific customer application or use. This Information is intended for use only by customers who

have the requisite experience and capability to determine the correct products for their application. Any technical advice inferred from this Information or otherwise

provided by us with reference to the use of our products is given gratis, and we assume no obligation or liability for the advice given or results obtained.