S101D02 Series
S201D02 Series
■ Features
IT(rms)≤1.2A, Zero Cross type
DIP 16pin
Triac output SSR
1. Output current, IT(rms)≤1.2A
2. Zero crossing functionary
3. 16 pin DIP package
4. High repetitive peak off-state voltage
(VDRM : 600V, S201D02 Series)
(VDRM : 400V, S101D02 Series)
5. Superior noise immunity
(dV/dt : MIN. 200V/µs, S101D02 Series)
(dV/dt : MIN. 100V/µs, S201D02 Series)
6. Response time, ton : MAX. 100µs
7. Lead-free terminal components are also available
(see Model Line-up section in this datasheet)
8. High isolation voltage between input and output
(Viso(rms) : 4.0kV)
■ Description
S101D02 Series and S201D02 Series Solid State
Relays (SSR) are an integration of an infrared emitting
diode (IRED), a Phototriac Detector and a main output
Triac. These devices are ideally suited for controlling
high voltage AC loads with solid state reliability while
providing 4.0kV isolation (Viso(rms)) from input to
output.
1
Notice The content of data sheet is subject to change without prior notice.
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in equipment using any SHARP
devices shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
S101D02 Series
S201D02 Series
■ Agency approvals/Compliance
1. Isolated interface between high voltage AC devices
and lower voltage DC control circuitry.
2. Switching motors, fans, heaters, solenoids, and
valves.
3. Power control in applications such as lighting and
temperature control equipment.
■ Applications
1.
Recognized by UL508, file No. E94758 (as model No.
S101D02/S201D02)
2. Approved by CSA 22.2 No.14, file No. LR63705 (as
model No. S101D02/S201D02)
3. Package resin : UL flammability grade (94V-0)
Sheet No.: D4-A01101EN
Date Mar. 31. 2004
© SHARP Corporation
∗Non-zero cross type is also available.(S101D01 Series/
S201D01 Series)
(Note) To radiate the heat, solder the lead pins to ,
on the pattern of the PCB without using a socket such
that there is no open pin left.
■ Internal Connection Diagram
16 15 13 11
11
9,
13
15
16
9
2 3 4 5 6 7
2
3
Anode
Cathode
Output (T1)
Output (T2)
Gate
NC
Zero Crossing Circuit
2
■ Outline Dimensions (Unit : mm)
1. Through-Hole [ex. S101D02F]
S101D02
θ : 0 to 13°
Epoxy resin
Factory identification mark
Date code (2 digit)
Anode mark
Model No.
9
16 15 13 11
2 3 4 5 6 7
2.54±0.25
19.82±0.5 7.62±0.3
0.26±0.1
6.5±0.5
3.4±0.5 3.5±0.5
0.5±0.1 1.2±0.3
0.5TYP.
θθ
CSA mark
2. Through-Hole [ex. S201D02F]
S201D02
θ : 0 to 13°
Epoxy resin
Factory identification mark
Date code (2 digit)
Anode mark
Model No.
9
16 15 13 11
2 3 4 5 6 7
2.54±0.25
19.82±0.5 7.62±0.3
0.26±0.1
6.5±0.5
3.4±0.5 3.5±0.5
0.5±0.1 1.2±0.3
0.5TYP.
θθ
CSA mark
S101D02 Series
S201D02 Series
Sheet No.: D4-A01101EN
Product mass : approx. 1.22g
Product mass : approx. 1.22g
4 7 9
Date code (2 digit)
Rank mark
There is no rank mark indicator and currently there are no rank offered for this device.
A.D.
1990
1991
1992
1993
1994
1995
1996
1997
1998
1999
2000
2001
Mark
A
B
C
D
E
F
H
J
K
L
M
N
Mark
P
R
S
T
U
V
W
X
A
B
C
Mark
1
2
3
4
5
6
7
8
9
O
N
D
Month
January
February
March
April
May
June
July
August
September
October
November
December
A.D
2002
2003
2004
2005
2006
2007
2008
2009
2010
2011
2012
·
·
··
·
·
2nd digit
Month of production
1st digit
Year of production
Factory identification mark
Factory identification Mark
no mark
Country of origin
Japan
* This factory marking is for identification purpose only.
Please contact the local SHARP sales representative to see the actural status of the
production.
3
repeats in a 20 year cycle
S101D02 Series
S201D02 Series
Sheet No.: D4-A01101EN
■ Electro-optical Characteristics
Parameter Symbol Unit
Input
Output
(Ta=25˚C)
Forward voltage
Reverse current
Repetitive peak OFF-state current
ON-state voltage
Holding current
Critical rate of rise of
OFF-state voltage
Zero cross voltage
Minimum trigger current
Isolation resistance
Turn-on time
VF
IR
IDRM
VT
IH
dV/dt
VOX
IFT
RISO
ton
V
µA
µA
V
mA
V/µs
V
mA
Ω
µs
IF=20mA
VR=3V
VD=VDRM
IT=1.2A
VD=6V
VD=1/√−
2 ·VDRM
I
F=
15mA
, Resistance load
VD=6V, RL=100Ω
DC500V,40 to 60%RH
V
D=
6V, R
L=
100Ω, I
F=
20mA
Conditions MIN. TYP. MAX.
Transfer
charac-
teristics
S101D02
S201D02
−
−
−
−
−
200
100
−
−
5
×
1010
−
1.2
−
−
−
−
−
−
−
−
1011
−
1.4
10
100
1.7
25
−
−
35
10
−
100
■ Absolute Maximum Ratings
4
Parameter Symbol Rating Unit
Input
Output
(Ta=25˚C)
Forward current
Reverse voltage
RMS ON-state current
Peak one cycle surge current
Repetitive peak
OFF-state voltage
Isolation voltage
Operating temperature
Storage temperature
Soldering temperature
*2
*1
IF
VR
IT(rms)
Isurge
VDRM
Viso(rms)
Topr
Tstg
Tsol
mA
V
A
A
V
kV
˚C
˚C
˚C
*4
*3
*3
50
6
1.2
12
400
600
4.0
−25 to +85
−40 to +125
260
*1 40 to 60%RH, AC for 1minute, f=60Hz
*2 For 10s
*3 Refer to Fig.1, Fig.2
*4 f=50Hz sine wave
S101D02
S201D02
S101D02 Series
S201D02 Series
1mm
Soldering area
Sheet No.: D4-A01101EN
Lead Form
Shipping Package
Model No.
Through-Hole
Sleeve
25pcs/sleeve
S101D02F
S201D02F
IFT[mA]
(VD=6V,
RL=100Ω)
MAX.10
400
MAX.10
600
VDRM
[V]
5
Please contact a local SHARP sales representative to see the actual status of the production.
S101D02 Series
S201D02 Series
Sheet No.: D4-A01101EN
■ Model Line-up (1) (Lead-free terminal components)
■ Model Line-up (2) (Lead solder plating components)
Lead Form
Shipping Package
Model No.
Through-Hole
Sleeve
25pcs/sleeve
S101D02
S201D02
IFT[mA]
(VD=6V,
RL=100Ω)
MAX.10
400
MAX.10
600
VDRM
[V]
6
S101D02 Series
S201D02 Series
0
80
70
60
50
40
30
20
10
Forward current IF (mA)
Ambient temperature Ta (˚C)
−25 10075 8550250
Fig.1 Forward Current vs. Ambient
Temperature
Fig.2 RMS ON-state Current vs.
Ambient Temperature
Sheet No.: D4-A01101EN
0
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
−25 10075 8550250
RMS ON-state current IT (rms) (A)
Ambient temperature Ta (˚C)
1
5
10
010.5 1.5 2 2.5 3
50
100
Forward current IF (mA)
Forward voltage VF (V)
−25˚C
50˚C
25˚C 0˚C
Ta=75˚C
Fig.3 Forward Current vs. Forward Voltage Fig.4 Minimum Trigger Current vs.
Ambient Temperature
0
2
4
6
10
8
12
−40 0−20 20 40 60 80 100
Minimum trigger current IFT (mA)
Ambient temperature Ta (˚C)
VD=6V
RL=100Ω
Fig.5-a ON-state Voltage vs.
Ambient Temperature (S101D02)
0.8
1.0
0.9
1.1
1.2
1.3
1.4
−40 0−20 20 40 60 80 100
ON-state voltage VT (V)
Ambient temperature Ta (˚C)
IT=1.2A
Fig.5-b ON-state Voltage vs.
Ambient Temperature (S201D02)
0.8
1.0
0.9
1.1
1.2
1.3
1.4
−40 0−20 20 40 60 80 100
ON-state voltage VT (V)
Ambient temperature Ta (˚C)
IT=1.2A
7
S101D02 Series
S201D02 Series
Fig.6-b Relative Holding Current vs.
Ambient Temperature (S201D02)
Sheet No.: D4-A01101EN
10
1 000
100
−40 0−20 20 40 60 80 100
Relative holding current IH(t˚C)/IH (25˚C)×100(%)
Ambient temperature Ta (˚C)
VD=6V
Fig.7-a ON-state Current vs.
ON-state Voltage (S201D02)
Remarks : Please be aware that all data in the
graph are just for reference.
Fig.7-a ON-state Current vs.
ON-state Voltage (S101D02)
1.6
1.2
1.4
1.0
0.8
0.6
0.4
0.2
0 1.51.00.5
ON-state current IT (A)
ON-state voltage VT (V)
IF=20mA
Ta=25˚C
0
1.6
1.2
1.4
1.0
0.8
0.6
0.4
0.2
0 1.51.00.5
ON-state current IT (A)
ON-state voltage VT (V)
IF=20mA
Ta=25˚C
0
Fig.8 Turn-on Time vs. Forward Current
Forward current IF (mA)
Turn-on time ton (µs)
10
10
20 30 40 50 100
20
30
40
50
100
VD=6V
RL=100Ω
Ta=25˚C
Fig.6-a Relative Holding Current vs.
Ambient Temperature (S101D02)
10
1 000
100
−40 0−20 20 40 60 80 100
Relative holding current IH(t˚C)/IH (25˚C)×100(%)
Ambient temperature Ta (˚C)
VD=6V
8
S101D02 Series
S201D02 Series
■ Design Considerations
Sheet No.: D4-A01101EN
● Design guide
In order for the SSR to turn off, the triggering current (IF) must be 0.1mA or less.
Particular attention needs to be paid when utilizing SSRs that incorporate zero crossing circuitry.
If the phase difference between the voltage and the current at the output pins is large enough, zero crossing
type SSRs cannot be used. The result, if zero crossing SSRs are used under this condition, is that the SSR
may not turn on and off irregardless of the input current. In this case, only a non zero cross type SSR should
be used in combination with the above mentioned snubber circuit selection process.
When the input current (IF) is below 0.1mA, the output Triac will be in the open circuit mode. However, if the
voltage across the Triac, VD, increases faster than rated dV/dt, the Triac may turn on. To avoid this situation,
please incorporate a snubber circuit. Due to the many different types of load that can be driven, we can
merely recommend some circuit values to start with : Cs=0.022µF and Rs=47Ω. The operation of the SSR
and snubber circuit should be tested and if unintentional switching occurs, please adjust the snubber circuit
component values accordingly.
When making the transition from On to Off state, a snubber circuit should be used ensure that sudden drops
in current are not accompanied by large instantaneous changes in voltage across the Triac.
This fast change in voltage is brought about by the phase difference between current and voltage.
Primarily, this is experienced in driving loads which are inductive such as motors and solenods.
Following the procedure outlined above should provide sufficient results.
For over voltage protection, a Varistor may be used.
Any snubber or Varistor used for the above mentioned scenarios should be located as close to the main
output triac as possible.
All pins shall be used by soldering on the board. (Socket and others shall not be used.)
● Degradation
In general, the emission of the IRED used in SSR will degrade over time.
In the case where long term operation and / or constant extreme temperature fluctuations will be applied to
the devices, please allow for a worst case scenario of 50% degradation over 5years.
Therefore in order to maintain proper operation, a design implementing these SSRs should provide at least
twice the minimum required triggering current from initial operation.
● Recommended Operating Conditions
Parameter
S101D02
S201D02
Symbol Unit
Input
Output
Input signal current at ON state
Input signal current at OFF state
Load supply voltage
Load supply current
Frequency
Operating temperature
IF(ON)
IF(OFF)
VOUT(rms)
IOUT(rms)
f
Topr
mA
mA
V
mA
Hz
˚C
−
−
−
Locate snubber circuit between output terminals
(Cs=0.022µF, Rs=47Ω)
−
−
Conditions
20
0
−
−
50
−20
25
0.1
120
240
IT(rms)×80%(∗)
60
80
MIN. MAX.
(∗) See Fig.2 about derating curve (IT(rms) vs. ambient temperature).
9
S101D02 Series
S201D02 Series
✩ For additional design assistance, please review our corresponding Optoelectronic Application Notes.
● Standard Circuit
Tr1
R1
D1
V1
+VCC
AC Line
Load
ZS
ZS : Surge absorption circuit (Snubber circuit)
SSR
13
2
3
11
Sheet No.: D4-A01101EN
■ Manufacturing Guidelines
● Soldering Method
Flow Soldering :
Flow soldering should be completed below 260˚C and within 10s.
Preheating is within the bounds of 100 to 150˚C and 30 to 80s.
Please solder within one time.
Hand soldering
Hand soldering should be completed within 3s when the point of solder iron is below 400˚C.
Please solder within one time.
Other notices
Please test the soldering method in actual condition and make sure the soldering works fine, since the impact
on the junction between the device and PCB varies depending on the tooling and soldering conditions.
10
S101D02 Series
S201D02 Series
Sheet No.: D4-A01101EN
11
S101D02 Series
S201D02 Series
Sheet No.: D4-A01101EN
Solvent cleaning :
Solvent temperature should be 45˚C or below. Immersion time should be 3minutes or less.
Ultrasonic cleaning :
The impact on the device varies depending on the size of the cleaning bath, ultrasonic output, cleaning time,
size of PCB and mounting method of the device.
Therefore, please make sure the device withstands the ultrasonic cleaning in actual conditions in advance of
mass production.
Recommended solvent materials :
Ethyl alcohol, Methyl alcohol and Isopropyl alcohol.
In case the other type of solvent materials are intended to be used, please make sure they work fine in
actual using conditions since some materials may erode the packaging resin.
● Cleaning instructions
This product shall not contain the following materials.
And they are not used in the production process for this device.
Regulation substances : CFCs, Halon, Carbon tetrachloride, 1.1.1-Trichloroethane (Methylchloroform)
Specific brominated flame retardants such as the PBBOs and PBBs are not used in this product at all.
● Presence of ODC
■ Package specification
12
12.0
6.7
5.8
10.8
520
±2
● Sleeve package
Through-Hole
Package materials
Sleeve : HIPS (with anti-static material)
Stopper : Styrene-Elastomer
Package method
MAX. 25pcs of products shall be packaged in a sleeve.
Both ends shall be closed by tabbed and tabless stoppers.
The product shall be arranged in the sleeve with its anode mark on the tabless stopper side.
MAX. 20 sleeves in one case.
Sleeve outline dimensions
(Unit : mm)
S101D02 Series
S201D02 Series
Sheet No.: D4-A01101EN
· The circuit application examples in this publication are
provided to explain representative applications of
SHARP devices and are not intended to guarantee any
circuit design or license any intellectual property rights.
SHARP takes no responsibility for any problems rela-
ted to any intellectual property right of a third party re-
sulting from the use of SHARP's devices.
· Contact SHARP in order to obtain the latest device
specification sheets before using any SHARP device.
SHARP reserves the right to make changes in the spec-
ifications, characteristics, data, materials, structure,
and other contents described herein at any time without
notice in order to improve design or reliability. Manufac-
turing locations are also subject to change without no-
tice.
· Observe the following points when using any devices
in this publication. SHARP takes no responsibility for
damage caused by improper use of the devices which
does not meet the conditions and absolute maximum
ratings to be used specified in the relevant specification
sheet nor meet the following conditions:
(i) The devices in this publication are designed for use
in general electronic equipment designs such as:
--- Personal computers
--- Office automation equipment
--- Telecommunication equipment [terminal]
--- Test and measurement equipment
--- Industrial control
--- Audio visual equipment
--- Consumer electronics
(ii) Measures such as fail-safe function and redundant
design should be taken to ensure reliability and safety
when SHARP devices are used for or in connection
with equipment that requires higher reliability such as:
--- Transportation control and safety equipment (i.e.,
aircraft, trains, automobiles, etc.)
--- Traffic signals
--- Gas leakage sensor breakers
--- Alarm equipment
--- Various safety devices, etc.
(iii) SHARP devices shall not be used for or in connec-
tion with equipment that requires an extremely high lev-
el of reliability and safety such as:
--- Space applications
--- Telecommunication equipment [trunk lines]
--- Nuclear power control equipment
--- Medical and other life support equipment (e.g.,
scuba).
· If the SHARP devices listed in this publication fall with-
in the scope of strategic products described in the For-
eign Exchange and Foreign Trade Law of Japan, it is
necessary to obtain approval to export such SHARP de-
vices.
· This publication is the proprietary product of SHARP
and is copyrighted, with all rights reserved. Under the
copyright laws, no part of this publication may be repro-
duced or transmitted in any form or by any means, elec-
tronic or mechanical, for any purpose, in whole or in
part, without the express written permission of SHARP.
Express written permission is also required before any
use of this publication may be made by a third party.
· Contact and consult with a SHARP representative if
there are any questions about the contents of this pub-
lication.
13
■ Important Notices
S101D02 Series
S201D02 Series
Sheet No.: D4-A01101EN
