LARGE CAPACITANCE ALUMINUM ELECTROLYTIC CAPACITORS
Overvoltage-proof design, 105C
CAT. No. E1001D
@No sparks against DC over-voltage
@Downsized from current KLG series
@Endurance with ripple current : 105C, 2000hours
@Non solvent-proof type
?SPECIFICATIONS
(at 20C, 120Hz)
(at 20C after 5 minutes)
(at 20C, 120Hz)
(at 120Hz)
(at 20C, 1MHz)
Category
Temperature Range
Rated Voltage Range
Capacitance Tolerance
Leakage Current
Dissipation Factor
(tane)
Low Temperature
Characteristics
(Max.Impedance Ratio)
ESL
Endurance
Shelf Life
Items
-
25 to +105C
200 & 400Vdc
P20% (M)
I=3 CV
Where, I : Max. leakage current (MA), C : Nominal capacitance (MF), V : Rated voltage (Vdc)
200Vdc : 0.15 max. (0.20 max. for FD=35mm)
400Vdc : 0.15 max.
Rated Voltage (Vdc)
Z(-25C) / Z(+20C)
50nH max.
The following specifications shall be satisfied when the capacitors are restored to 20C after subjected to DC voltage with the rated
ripple current is applied for 2000 hours at 105C.
Capacitance change [P20% of the initial value
D.F. (tanE)[200% of the initial specified value
Leakage current [The initial specified value
The following specifications shall be satisfied when the capacitors are restored to 20C after exposing them for 1000 hours at 105C
without voltage applied.
Capacitance change [P15% of the initial value
D.F. (tanE)[150% of the initial specified value
Leakage current [The initial specified value
Characteristics
200V
4400V
4
?DIMENSIONS [mm]
?PART NUMBERING SYSTEM
CHA 400 VSSN 100 M 25A
Case code
Cap tolerance (P20%)
Nominal cap in MF
Terminal type
Rated voltage in volts
Series name
Case
code Case
size
fDbL
Case
code Case
size
fDbL
Case
code Case
size
fDbL
Case
code Case
size
fDbL
22S
22A
22B
22C
22D
22B20
22B25
22B30
22B35
22B40
30A
30B
30C
30D
30E
30B25
30B30
30B35
30B40
30B45
35A
35B
35C
35B25
35B30
35B35
25A
25B
25C
25D
25E
25.4B25
25.4B30
25.4B35
25.4B40
25.4B45
?CASE CODE [mm]
?RATED RIPPLE CURRENT MULTIPLIERS
@Frequency Multipliers
50
0.77 120
1.00 300
1.16 1k
1.30 10k
1.41 50k
1.43
Frequency (Hz)
200 & 400V
dc
@Standard Terminal Type : VSSN (F22 to F35)
4.0P0.5
F
D+1max.
Vent
Sleeve
LP2
Negative mark
PC board pin-out
10
2
-
F2
downsized
downsized
longer life CHA
KLG
LXH
*No plastic disk is the standard design.
(1/2)
ALUMINUM ELECTROLYTIC CAPACITORS
SMQ-Series(Snap-in)
LARGE CAPACITANCE ALUMINUM ELECTROLYTIC CAPACITORS
Overvoltage-proof design, 105C
CAT. No. E1001D
180
220
270
330
390
470
560
680
820
1,000
1,200
22B20
0.82
22B20
0.90
22B25
1.02
22B30
1.20
22B30
1.35
22B35
1.45
22B40
1.62
25.4B25
1.20
25.4B25
1.35
25.4B30
1.45
25.4B30
1.60
25.4B35
1.82
25.4B45
2.11
30B25
1.47
30B25
1.60
30B30
1.81
30B35
2.11
30B35
2.40
30B45
2.69
35B25
1.86
35B25
2.11
35B30
2.40
35B35
2.65
200
22 25.4 30 35
mFVdc
fDmFVdc
fD
56
68
82
100
120
150
180
220
270
330
22B20
0.45
22B20
0.51
22B25
0.58
22B25
0.66
22B30
0.76
22B35
0.85
22B40
0.94
25.4B25
0.66
25.4B25
0.76
25.4B30
0.85
25.4B35
0.95
25.4B35
1.24
25.4B45
1.30
30B25
0.85
30B25
0.95
30B30
1.24
30B35
1.30
30B40
1.47
35B25
1.30
35B30
1.47
400
22 25.4 30 35
Upper : Case size FDBL (mm)
Lower :
Rated ripple current (Arms) at 105C, 120Hz
Upper : Case size FDBL (mm)
Lower :
Rated ripple current (Arms) at 105C, 120Hz
?STANDARD RATINGS
?DC OVERVOLTAGE TEST CONDITIONS
The vent will operate and the capacitor shall become an open circuit without burning materials
when the following excess DC voltage is applied.
@Test DC voltage
Rated Voltage
200V
dc
400V
dc
Nominal Capacitance
<
330MF
330[C
<
470MF
]470MF
<
100MF
100[C
<
220MF
]220MF
Current Limit
4A
5A
7A
2A
4A
7A
Test Voltage
300/375V
dc
500/600V
dc
@Test Circuit
AC input SW CX
+
-
Constant DC voltage/current power supply
(2/2)
ALUMINUM ELECTROLYTIC CAPACITORS
SMQ-Series(Snap-in)
