Connectors BCL series Connectors for Mobile Equipment for Mobile Equipment Outline Features Principal Applications The BCL series are connectors for cradles, which have been designed for small sized mobile peripherals (PDAs). They are 1 mm pitch connectors, which save on board space and are low in cost. * These male connectors are one-piece molded units with gasket, making these connectors waterproof. * Since the contacts of these female connectors are cleaned by a wiping effect, these contact surfaces become stable, and 10,000 insertion and extraction cycles are ensured. * Polarity key location can be changed. * These cable mount connectors are solder type, which can be attached to cables such as USB serial bus cables. PDA, etc. BCL-C Series Electrical Characteristics Rated voltage 21V Rated current Signal contacts : 0.7A Power-supply contacts : 2.8A Insulation resistance 500 megohms MIN. at 500V DC Dielectric withstanding voltage 300V AC (r.m.s.) for one minute Document Disclaimer When placing orders with us, minimum order quantities are set for every product. Be sure to contact us before starting preliminary design of PCBs using our connectors. The specifications and information shown in the catalog are subject to change without notice. Reflow temperature profile (for reference purposes) Flow temperature profile (for reference purposes) 5sec (Peak) 250C 2605C 220C 150~180C (Full heating period) 30sec 100~130C 30~60sec (Preheating period) 60~120 sec The reflow temperature profile shown in this drawing is for reference purposes. This profile depends on requirements such as reflow equipment, soldering paste, and PCB size. Thus, this profile may not meet with your specific situation. Please evaluate your PCB-mounting soldering and set your own reflow temperature profile. Applicable products BCL-C18LMYG The profile shown in this drawing is applicable only for those products shown above. The flow temperature profile as shown above is for reference purposes. This profile depends on requirements such as the PCB size. Thus, this profile may not meet with your specific situation. Please evaluate your PCB-mounting soldering and set your own flow temperature profile. Applicable products BCL-C18LFDG1 The profile shown in this drawing is applicable only for those products shown above. Product List Right-angle SMT type male connector for mobile equipment BCL-C18LMYG G-18BCL BCL series...4 Cradle-side right-angle through hole type female connector for mobile equipment BCL-C18LFDG1 G-19BCL BCL series...5 Cable-side straight soldering type female connector for mobile equipment BCL-C18SPFSG1 G-20BCL BCL series...6 Cable mount female connector with plastic hood for mobile equipment BCL-C18SP G-21BCL BCL series...7 For mobile equipment Right-angle SMT type male connector for mobile equipment BCL-C18LMYG For PCB Right-angle SMT Configuration of product Part No. BCL-C 18 LMY G Series name No. of contacts: 18 Type of contact LMY: Right-angle SMT type, male Contact plating G: Gold plate 24.8 19.6 15 3.2 34.60.1 29.6 POS.#P1 8.4 8 4.8 POS.#1 POS.#16 1.5 23.8 Power-supply contacts Latch .1 +0 0 3 2. o 1.5 Screw Gasket 0 5.2+0.1 34.60.1 0 29.8+0.1 R0.3 4.2 Insulator Signal contacts +0.1 0 Components +0.1 0 23.80.05 Recommended panel cut-out dimensions t = 1.4 mm MAX. Vacuum cap Mating connectors: BCL-C18LFDG1, BCL-C18SP (BCL-C18SPFSG1) SMT Press-in 1.6MAX. o0.8 1.2 Through hole 0.90.05 20.05 5.9 0.9 M2 Screw depth 2.2 Area (See Note #2) 7.4 4 board-edge Recommended PCB layout t = 1.0 mm POS.#P2 41 34.6 19.6 115=15 2.2 0 10.05 0.70.05 .9 +0.1 1.40.05 o0 0.40.05 2.50.05 1.6 0.4 0.3 0.8 24.80.1 19.60.1 115=150.1 IDC Wire Soldering Crimping wrapping Others 1.7 6.6 8 9.5 Note 1: These products are one-piece units with molded-in contacts and gasket, making these connectors waterproof (IPX5 or equivalent). Note 2: Area indicates support for 18 pos. Connector during soldering assembly process. Design to breakaway after assembly. For mobile equipment Cradle-side right-angle through hole type female connector for mobile equipment BCL-C18LFDG1 Cradle side For PCB Right-angle Through hole Configuration of product Part No. BCL-C 18 LFD G1 Series name No. of contacts: 18 Type of contact LFD: Right-angle through hole type, female Contact plating G1: Gold plate 37.5 34.5 31.8 24.5 19.6 POS.#P2 POS.#P1 1(16-1)=15 1 A 1.4 POS.#16 A' A-A' cross section 23.8 POS.#1 29.8 5.6 10 1.6 1.8 3.8 3.4 34.50.05 0.650.05 2.3 8-o0.7 Insulator Signal contacts Power-supply contacts Metal locating pin 2 2 10.05 0.05 19.6 20.05 Components R0.325 2.10.1 2 R0.4 Board-edge 0.05 3 REF. 0.8 0.05 0.1 Recommended PCB layout t = 1.0 mm Mating connectors: BCL-C18LMYG Others Wire wrapping Crimping Soldering IDC Press-in SMT Through hole For mobile equipment Cable-side straight soldering type female connector for mobile equipment BCL-C18SPFSG1 Cable side Soldering Configuration of product Part No. BCL-C 18 SPFS G1 Series name No. of contacts: 18 Type of contact SPFS: Straight soldering type, female Contact plating G1: Gold plate A TM 14.5 JAPAN 1.2 1 A' A-A' cross section 15 19.6 24.5 POS.#P2 POS.#P1 29.8 Components Insulator Shorter signal contacts Longer signal contacts Power-supply contacts Mating connectors: BCL-C18LMYG Through hole SMT Press-in IDC Wire Soldering Crimping wrapping Others 7 0.6 4.3 POS.#1 3.4 POS.#16 0.7 31.8 For mobile equipment Cable mount female connector with plastic hood for mobile equipment BCL-C18SP Cable side Female connector with plastic hood Configuration of product Part No. BCL-C 18 SP Series name No. of contacts: 18 BCL-C18SPFSG1 with plastic hood 34.8 29.8 26.6 9.8 13.1 2.7 6 25 24.5 31.8 POS.#P2 POS.#P1 Components Screw Latch POS.#16 POS.#1 Plastic hood A Plastic hood B Note: These products consist of a connector BCL-C18SPFSG1 and plastic hood. Connector Mating Connector: BCL-C18LMYG Others Wire wrapping Crimping Soldering IDC Press-in SMT Through hole