10Gbps 60km BIDI Simplex LC SFP+ Transceiver PSP96-B7360 & PSP96-B3760 Primus IT Limited Features 10Gbps 60km Bi-Directional Simplex LC SFP+ Transceiver PSP96-B7360 & PSP96-B3760 Up to 10.6Gbps data links 1270nm DFB Laser and APD photo-detector for PSP96-B7360 1330nm DFB Laser and APD photo-detector for PSP96-B3760 Up to 60km on 9/125m SMF Simplex LC receptacle optical interface compliant Hot pluggable All-metal housing for superior EMI performance RoHS6 compliant (lead free) Operating case temperature: Commercial: -5C to +70C Extended: -20C to +80C Industrial: -40C to +85C Applications 10GBASE-ER/EW 10G Ethernet 10G Fibre Channel 10G SONET Other optical links Standards Compliant with SFP+ MSA Compliant with SFF-8472 Compatible with IEEE802.3ae Description The SFP+ transceivers are designed for use in 10-Gigabit Ethernet links up to 60km over Single Mode Fiber. The transceivers are compatible with SFP+ MSA and SFF-8472. For further information, please refer to SFP+ MSA and SFF-8472. Page 1 10Gbps 60km BIDI Simplex LC SFP+ Transceiver PSP96-B7360 & PSP96-B3760 Primus IT Limited Module Block Diagram Absolute Maximum Ratings Parameter Symbol Min. Power Supply Voltage VCC Storage Temperature Typical Max. Unit 0 3.6 V Ts -40 +85 C Relative Humidity RH 0 85 % RX Input Average Power Pmax - -6 dBm Symbol Min. Typical Max. Unit Power Supply Voltage VCC 3.13 3.3 3.46 V Power Supply Current ICC 300 mA Recommended Operating Environment Parameter Commercial Operating Case Temperature Extended TC Industrial Data Rate -5 +70 -20 +80 -40 +85 10.3125 Page 2 C Gbps 10Gbps 60km BIDI Simplex LC SFP+ Transceiver PSP96-B7360 & PSP96-B3760 Primus IT Limited Electrical Characteristics Parameter Symbol Min. Typical Max. Unit Note Input Differential Impedance Rin 90 100 110 Differential Data Input Swing Vin PP 180 700 mV Transmit Disable Voltage VD Vcc - 1.3 Vcc V Transmit Enable Voltage VEN Vee Vee+ 0.8 V Differential Data Output Swing Vout PP 300 850 mV LOS Fault Vlos fault Vcc - 0.5 Vcc_host V 2 LOS Normal Vlos norm Vee Vee+0.5 V 2 Transmitter Section 1 Receiver Section Notes: 1. Connected directly to TX data input pins. AC coupling from pins into laser driver IC. 2. LOS is an open collector output. Should be pulled up with 4.7k - 10k on the host board. Normal operation is logic 0; loss of signal is logic 1. Optical Parameters Parameter Symbol Min. Typical Max. Unit Note 1260 1270 1280 nm PSP96-B7360 1320 1330 1340 nm PSP96-B3760 1 nm Transmitter Section Centre Wavelength c Spectral Width(-20dB) Side Mode Suppression Ratio SMSR 30 Average Optical Power (avg.) Pout 1 Laser Off Power Poff - Extinction Ratio ER Relative Intensity Noise RIN Optical Rise/Fall Time tr / tf Optical Return Loss Tolerance Output Optical Eye dB +5 dBm - -30 dBm 3.5 - - dB - - -128 dB/Hz - 50 ps - 12 dB - Compliant with IEEE802.3ae eye masks when filtered 1 2 3 2 Receiver Section Receiver Center Wavelength c 1320 1330 1340 nm PSP96-B7360 1260 1270 1280 nm PSP96-B3760 -7 dBm 4 Receiver Sensitivity in Average Power Los Assert Sen -20 LOSA -30 - - dBm Los Dessert LOSD - - -21 dBm Los Hysteresis LOSH 0.5 - 5 dB Overload Pin-max - - -7 dBm Receiver Reflectance - - -12 dB Receiver Power (damage) - - -6 dBm Page 3 4 10Gbps 60km BIDI Simplex LC SFP+ Transceiver PSP96-B7360 & PSP96-B3760 Primus IT Limited Notes: 1. The optical power is launched into 9/125m SMF. 31 2. Measured with a PRBS 2 -1 test pattern @10.3125Gbps. 31 3. Unfiltered, 20-80%. Measured with a PRBS 2 -1 test pattern @10.3125Gbps. 31 -12 4. Measured with a PRBS 2 -1 test pattern @10.3125Gbps, ER=4dB, BER <10 . Timing Characteristics Parameter TX_Disable Assert Time TX_Disable Negate Time Time to Initialize Tx_Fault Assert Tx_Fault Reset Rx_LOS Assert Delay Rx_LOS Negate Delay Clock Frequency Symbol t_off t_on t_start_up t_fault_on t_reset t_los_on t_los_off fSCL Min. Typical Max. 100 2 300 1 Unit us ms ms ms us us us kHz 10 100 100 400 0 Digital Diagnostic Monitor Characteristics (DDM) The following digital diagnostic characteristics are defined over the Recommended Operating Environment unless otherwise specified. It is compliant to SFF8472 Rev10.2 with internal calibration mode. For external calibration mode please contact our sales stuff. Parameter Symbol Min. Max. Unit Temperature Monitor Absolute Error DMI_Temp -3 3 C Laser Power Monitor Absolute Error DMI_TX -3 3 dB RX Power Monitor Absolute Error DMI_RX -3 3 dB Supply Voltage Monitor Absolute Error DMI_VCC -3% 3% V Bias Current Monitor Absolute Error DMI_Ibias -10% 10% mA Digital Diagnostic Memory Map (Compliant with SFF-8472) The transceivers provide serial ID memory contents and diagnostic information about the present operating conditions by the 2-wire serial interface (SCL, SDA). The diagnostic information with internal calibration or external calibration all are implemented, including received power monitoring, transmitted power monitoring, bias current monitoring, supply voltage monitoring and temperature monitoring. The digital diagnostic memory map specific data field defines as following (For further information, please refer to SFF-8472). Page 4 10Gbps 60km BIDI Simplex LC SFP+ Transceiver PSP96-B7360 & PSP96-B3760 Primus IT Limited Pin Definitions Page 5 10Gbps 60km BIDI Simplex LC SFP+ Transceiver PSP96-B7360 & PSP96-B3760 Primus IT Limited Pin Descriptions Pin Signal Name Plug Seq. Notes VeeT Description Module Transmitter Ground 1 1 1 2 TX FAULT Module Transmitter Fault 3 3 TX Disable 4 SDA Transmitter Disable; Turns off transmitter laser output 2-Wire Serial Interface Data Line 5 SCL 2-Wire Serial Interface Clock 6 Mod_ABS 7 RS0 8 LOS 9 RS1 Receiver Loss of Signal Indication Active LOW Transmitter Rate Select (not used) VeeR Module Receiver Ground 1 1 VeeR Module Receiver Ground 1 1 RD- Receiver Inverted Data Output 3 RD+ Receiver Non-Inverted Data Output 3 VeeR Module Receiver Ground 1 VccR Module Receiver 3.3 V Supply 2 VccT Module Transmitter 3.3 V Supply 2 VeeT Module Transmitter Ground 1 TD+ Transmitter Non-Inverted Data Input 3 TD- Transmitter Inverted Data Input 3 VeeT Module Transmitter Ground 1 10 11 12 13 14 15 16 17 18 19 20 Module Definition, Grounded in the module Receiver Rate Select (not used) 3 3 2 3 2 3 3 3 3 Notes: Plug Seq.: Pin engagement sequence during hot plugging. 1. Module ground pins GND are isolated from the module case. 2. Shall be pulled up with 4.7K-10Kohms to a voltage between 3.15V and 3.45V on the host board. Recommended Power Interface Circuit Page 6 1 1 1 10Gbps 60km BIDI Simplex LC SFP+ Transceiver PSP96-B7360 & PSP96-B3760 Primus IT Limited Recommended Interface Circuit Mechanical Dimensions Page 7 10Gbps 60km BIDI Simplex LC SFP+ Transceiver PSP96-B7360 & PSP96-B3760 Primus IT Limited Ordering information Part Number PSP96-B7360 PSP96-B7360E PSP96-B7360T PSP96-B3760 PSP96-B3760E PSP96-B3760T Product Description TX 1270nm, RX 1330nm, 10Gbps, 60km, Bi-Directional Simplex -5C ~ +70C, With DDM. TX 1270nm, RX 1330nm, 10Gbps, 60km, Bi-Directional Simplex -20C ~ +80C, With DDM. TX 1270nm, RX 1330nm, 10Gbps, 60km, Bi-Directional Simplex -40C ~ +85C, With DDM. TX 1330nm, RX 1270nm, 10Gbps, 60km, Bi-Directional Simplex -5C ~ +70C, With DDM. TX 1330nm, RX 1270nm, 10Gbps, 60km, Bi-Directional Simplex -20C ~ +80C, With DDM. TX 1330nm, RX 1270nm, 10Gbps, 60km, Bi-Directional Simplex -40C ~ +85C, With DDM. LC SFP+ Transceiver, LC SFP+ Transceiver, LC SFP+ Transceiver, LC SFP+ Transceiver, LC SFP+ Transceiver, LC SFP+ Transceiver, References 1. "Specifications for Enhanced Small Form Factor Pluggable Module SFP+", SFF-8431, Rev 4.1, July 6, 2009. 2. "Improved Pluggable Form factor", SFF-8432, Rev 4.2, Apr 18, 2007. 3. "Diagnostic Monitoring Interface for Optical Transceivers" SFF-8472, Rev 10.2, June 1, 2007. 4. IEEE802.3ae 2002. Important Notice Performance figures, data and any illustrative material provided in this data sheet are typical and must be specifically confirmed in writing by PRIMUS IT before they become applicable to any particular order or contract. In accordance with the PRIMUS IT policy of continuous improvement specifications may change without notice. The publication of information in this data sheet does not imply freedom from patent or other protective rights of PRIMUS IT or others. Further details are available from any PRIMUS IT sales representative. Contact Information PRIMUS IT LIMITED 1HongKongRM M4/F Continental Mansion 300 King's RD HK 2Tel:+86 0755-25924025 3Fax:+86 0755-25924051 4Websitehttp://www.primus-it.com 5Emailsales@primus-it.com Page 8