LM358N - INTERSIL - Datasheet.Directory

CLC014

CLC014 Adaptive Cable Equalizer for High-Speed Data Recovery

Literature Number: SNLS010D

CLC014

OBSOLETE

August 20, 2010

Adaptive Cable Equalizer for High-Speed Data Recovery

General Description

National's CLC014 adaptive cable equalizer is a low-cost

monolithic solution for equalizing data transmitted over cable

(or any media with similar dispersive loss characteristics).

The CLC014 simplifies the task of high-speed data recovery

with a one-chip solution and a minimal number of external

components. The equalizer automatically adapts to equalize

any cable length from zero meters to lengths that attenuate

the signal by 40 dB at 200 MHz. This corresponds to 300 me-

ters of Belden 8281 or 120 meters of Category 5 UTP (un-

shielded twisted pair).

The CLC014 provides superior jitter performance:

180pspp for 270 Mbps data that has passed through 200

meters of Belden 8281 cable. This exceptional perfor-

mance provides wide error margin in digital data links.

The equalizer operates on a single supply with a power con-

sumption of only 290 mW. The small 14-pin SOIC package

allows for high-density placement of components for multi-

channel applications such as routers. The equalizer operates

over a wide range of data rates from less than 50 Mbps to

rates in excess of 650 Mbps.

The equalizer is flexible in allowing either single-ended or dif-

ferential input drive. Its high common mode rejection provides

excellent immunity to interference from noise sources. On-

chip quantized feedback eliminates baseline wander.

Additional features include a carrier detect output and an out-

put mute pin which, when tied together, mute the output when

no signal is present. A buffered eye monitor output is provid-

ed, for viewing the equalized signal prior to the comparator.

Differential AEC pins allow the user to set the internal adap-

tive loop time constant with one external capacitor. Also, the

CLC014 is insensitive to the pathological patterns inherent in

the video industry standards.

Features

■Automatic equalization of coaxial and twisted pair cables

■Carrier detection and output mute

■Output eye monitor

■Single supply operation: +5V or −5.2V

■Single-ended or differential input

■Low cost

Applications

■SMPTE 259M serial digital interfaces: NTSC/PAL, 4:2:2

component and wide screen; also 540 Mbps (4:4:4:4)

■Serial digital video routing and distribution

■Serial digital data equalization and reception

■Data recovery equalization: ATM, CAD networks, medical,

set top terminals, industrial video networks

Key Specifications

■Low jitter: 180pspp @ 270 Mbps through 200 meters of

Belden 8281 coaxial cable

■High data rates: < 50 Mbps to > 650 Mbps

■Excellent input return loss: 19 dB @ 270 MHz

■Low supply current: 58 mA

■Equalizes up to 300+ meters of Belden 8281 or 120 meters

of Cat 5 UTP cable

Typical Application

10005604

100056 Version 11 Revision 6 Print Date/Time: 2010/08/23 16:48:25

CLC014 Adaptive Cable Equalizer for High-Speed Data Recovery

10005602 10005603

Connection Diagram

Pinout SOIC

10005601

14-Pin SOIC

Order Number CLC014AJE

See NS Package Number M14A

www.national.com 2

100056 Version 11 Revision 6 Print Date/Time: 2010/08/23 16:48:25

CLC014

Absolute Maximum Ratings (Note 1)

If Military/Aerospace specified devices are required,

please contact the National Semiconductor Sales Office/

Distributors for availability and specifications.

Supply Voltage (VCC–VEE)−0.3V, +6.5V

Maximum Junction Temperature +150°C

Storage Temperature Range −65°C to +150°C

Lead Temperature

(Soldering 4 sec.) +260°C

ESD Rating (Note 14) <500V

θJA 14-Pin SOIC (AJE) 95°C/W

MTTF (based on limited life test data) 4.8 x 107 hours

Recommended Operating

Conditions

Supply Voltage (VCC–VEE)4.5V to 5.5V

Operating Temperature Range −40°C to +85°C

Series Input Resistance

(In Series w/DI & DI) 100Ω

Input Coupling Capacitance 1.0 μF

AEC Capacitor (Connected

between AEC+ & AEC−) 50 pF to 1 μF

Cable Input Voltage Swing

(Note 4)720 to 880 mVpp

DO/DO Minimum Voltage

(Note 15)VCC–1.6V

Electrical Characteristics

(VCC = +5V, VEE = 0V, signal source swing = 0.8 Vpp(Note 4), CAEC = 100 pF)

Parameter Conditions Typ

+25°C

Min/Max

+25°C

Min/Max

−40°C to

+85°C

Units

DYNAMIC PERFORMANCE

Residual Jitter

100 meters Belden 8281 270 Mbps PRN (Note 5) 150 250 400 pspp

200 meters Belden 8281 270 Mbps PRN (Note 5) 180 250 400 pspp

300 meters Belden 8281 270 Mbps PRN (Note 3, Note 5) 350 500 750 pspp

Equalization Time Constant

100 meters Belden 8281 CAEC = 100 pF (Note 6) 1.5 _ _ μs

200 meters Belden 8281 CAEC = 100 pF (Note 6) 2.0 _ _ μs

300 meters Belden 8281 CAEC = 100 pF (Note 6) 3.2 _ _ μs

output rise and fall time (20%–80%) Rcollector = 75Ω 750 _ _ ps

output duty cycle distortion 30 _ _ ps

minimum average transition density 1/50 _ _ trans/ns

maximum average data rate 150m Belden 8281 (Note 7) 650 _ _ Mbps

VCC Jitter Sensitivity

27 MHz 0.85 _ _ ns/V

270 MHz 1.90 _ _ ns/V

VEE Jitter Sensitivity

27 MHz 0.55 _ _ ns/V

270 MHz 1.45 _ _ ns/V

STATIC PERFORMANCE

Supply Current (Includes Output Current)

VAEC = 0V (Note 3) 58 48/68 40/75 mA

VAEC = 0.4V (Note 3) 53 43/64 37/70 mA

Input and Output Parameters

DO/DO output current 10 8.7/11.3 8.0/12 mA

DO/DO output voltage swing Rcollector = 75Ω (Note 3)750 650/850 600/900 mV

DI/DI common mode voltage 3.4 _ _ V

AEC differential voltage Belden 8281 1.5 _ _ mV/meter

3 www.national.com

100056 Version 11 Revision 6 Print Date/Time: 2010/08/23 16:48:25

CLC014

Parameter Conditions Typ

+25°C

Min/Max

+25°C

Min/Max

−40°C to

+85°C

Units

AEC+/AEC− common mode 3.6 _ _ V

output eye monitor (OEM) bias potential 3.2 _ _ V

carrier detect (CD) current output-HIGH CD VOH = 4.5V −400 _ _ μA

carrier detect (CD) current output-LOW CD VOL = 0.5V 600 _ _ μA

MUTE voltage input-HIGH (Note 3) 1.8 2.0 2.0 V

MUTE voltage input-LOW (Note 3) 1.2 0.8 0.8 V

MUTE current input-HIGH VIH = 5V (Note 3) 5.0 ±100 ±500 nA

MUTE current input-LOW VIL = 0V (Note 3) 0.2 ±100 ±500 nA

TIMING PERFORMANCE

CD Response Time

carrier applied (Note 8) 1.0 _ _ μs

carrier removed (Note 9) 12 _ _ μs

MUTE response time (Note 10) 2.0 _ _ ns

MISCELLANEOUS PERFORMANCE

input resistance single-ended 7.3 _ _ kΩ

input capacitance single-ended (Note 11) 1.0 _ _ pF

input return loss @ 270 MHz Zo = 75Ω (Note 12)19 _ _ dB

maximum cable attenuation 200 MHz (Note 13) 40 _ _ dB

Note 1: “Absolute Maximum Ratings” are those values beyond which the safety of the device cannot be guaranteed. They are not meant to imply that the devices

should be operated at these limits. The table of “Electrical Characteristics” specifies conditions of device operation.

Note 2: Min/max ratings are based on product characterization and simulation. Individual parameters are tested as noted. Outgoing quality levels are determined

from tested parameters.

Note 3: J-level: spec. is 100% tested at +25°C.

Note 4: These specifications assume an 800 mVpp signal at the cable input. Levels above and below 800 mV are allowable, but performance may vary. The cable

will attenuate the signal prior to entering the equalizer.

Note 5: Peak-to-peak jitter is defined as 6 times the rms jitter.

Note 6: For more information, see “CLC014 Operation” and “Design Guidelines”.

Note 7: 50% eye opening.

Note 8: Time from application of a valid signal to when the CD output asserts high.

Note 9: Time from the removal of a valid signal to when the CD output asserts low.

Note 10: Time from assertion of MUTE to when the output responds.

Note 11: Device only. Does not include typical pc board parasitics.

Note 12: Includes typical pc board parasitics.

Note 13: This sets the maximum cable length for the equalizer.

Note 14: Human body model, 1.5 kΩ in series with 100 pF; based on limited test data.

Note 15: To maintain specified performance, do not reduce DO/DO below this level.

www.national.com 4

100056 Version 11 Revision 6 Print Date/Time: 2010/08/23 16:48:25

CLC014

Typical Performance Characteristics

10005605 10005608

10005606 10005609

10005607 10005610

5 www.national.com

100056 Version 11 Revision 6 Print Date/Time: 2010/08/23 16:48:25

CLC014

10005611 10005614

10005612 10005615

10005613 10005616

www.national.com 6

100056 Version 11 Revision 6 Print Date/Time: 2010/08/23 16:48:25

CLC014

10005617

10005618

10005619

7 www.national.com

100056 Version 11 Revision 6 Print Date/Time: 2010/08/23 16:48:25

CLC014

Pin Definitions

Name Pin # Description

DI, DI 8, 9 Differential data inputs.

DO, DO 13, 14 Differential collector data

outputs (ECL compatible).

AEC+,

AEC−

6, 7 AEC loop filter pins.

A capacitor connected between

these pins governs the loop

response for the adaptive

equalization loop.

OEM 3 Eye monitor output. The output

of the equalization filter.

CD 5 Carrier detect. (Low when no

signal is present).

MUTE 12 Output MUTE. (Active low.)

Carrier detect may be tied to

this pin to inhibit the output

when no signal is present.

VCC 1, 2, 4 Positive supply pins (ground or

+5V).

VEE 10, 11 Negative supply pins (−5.2V or

ground).

Operation

The CLC014 Adaptive Cable Equalizer provides a complete

solution for equalizing high-bit-rate digital data transmitted

over long transmission lines. The following sections furnish

design and application information to assist in completing a

successful design:

•Block diagram explanation of the CLC014

•Recommended standard input and output interface

connections

•Common applications for the CLC014

•Measurement, PC layout, and cable emulation boxes

For applications assistance in the U.S., call 800-272-9959 to

contact a technical staff member.

10005620

FIGURE 1. CLC014 Equalizer Application Circuit

BLOCK DESCRIPTION

The CLC014 is an adaptive equalizer that reconstructs serial

digital data received from transmission lines such as coaxial

cable or twisted pair. Its transfer function approximates the

reciprocal of the cable loss characteristic. The block diagram

in Figure 2 depicts the main signal conditioning blocks for

equalizing digital data at the receiving end of a cable. The

CLC014 receives baseband differential or single-ended digi-

tal signals at its inputs DI and DI.

The Equalizer block is a two-stage adaptive filter. This filter

is capable of equalizing cable lengths from zero meters to

lengths that require 40 dB of boost at 200 MHz.

The Quantized Feedback Comparator block receives the

differential signals from the equalizer filter block. This block

includes two comparators. The first comparator incorporates

a self-biasing DC restore circuit. This is followed by a second

high-speed comparator with output mute capability. The sec-

ond comparator receives and slices the DC-restored data. Its

outputs DO and DO are taken from the collectors of the output

transistors. MUTE latches DO and DO when a TTL logic low

level is applied.

The Adaptive Servo Control block produces the signal for

controlling the filter block, and outputs a voltage proportional

to cable length. It receives differential signals from the output

of the filter block and from the quantized-feedback compara-

tor (QFBC) to develop the control signal. The servo loop

response is controlled by an external capacitor placed across

the AEC+ and AEC− pins. Its output voltage, as measured

differentially across AEC+ and AEC−, is roughly proportional

to the length of the transmission line. For Belden 8281 coaxial

cable this differential voltage is about 1.5 mV/meter. Once this

voltage exceeds 500 mV, no additional equalization is pro-

vided.

The Carrier Detect (CD) block monitors the signal power out

of the equalizing filter and compares it to an internal reference

to determine if a valid signal is present. A CMOS high output

indicates that data is present. The output of CD can be con-

nected to the MUTE input to automatically latch the outputs

(DO and DO), preventing random transitions when no data is

present.

The Output Eye Monitor (OEM) provides a single-ended

buffered output for observing the equalized eye pattern. The

OEM output is a low impedance high-speed voltage driver

capable of driving an AC-coupled 100Ω load.

10005621

FIGURE 2. CLC014 Block Diagram

www.national.com 8

100056 Version 11 Revision 6 Print Date/Time: 2010/08/23 16:48:25

CLC014

DEVICE TESTING

Performance or compliancy testing of the CLC014 with Cable

Clones is not allowed. Use of these devices is contrary to the

product's specifications and test procedures. Testing for prod-

uct specifications or performance using cable clones is invalid

since cable clones have a different frequency response than

the actual cable. Testing with full length cable samples is rec-

ommended.

Input Interfacing

The CLC014 accepts either differential or single-ended input

voltage specified in Static Performance. The following sec-

tions show several suggestions for interfaces for the inputs

and outputs of the CLC014.

SINGLE-ENDED INPUT INTERFACE: 75Ω Coaxial Cable

The input is connected single-ended to either DI or DI as

shown in Figure 3. Balancing unused inputs helps to lessen

the effects of noise. Use the equivalent termination of 37.5Ω

to balance the input impedance seen by each pin. It also helps

to terminate grounds at a common point. Resistors Rx and

R y are recommended for optimum performance. The equal-

izer inputs are self-biasing. Signals should be AC coupled to

the inputs as shown in Figure 3.

10005622

FIGURE 3. Single-Ended 75Ω Cable Input Interface

DIFFERENTIAL INPUT INTERFACE: Twisted Pair

A recommended differential input interface is shown in Figure

4. Proper voltage levels must be furnished to the input pins

and the proper cable terminating impedance must be provid-

ed. For Category 5 UTP this is approximately 100Ω. Figure

4 shows a generalized network which may be used to receive

data over a twisted pair. Resistors R1 and R2 provide the

proper terminating impedance and signal level adjustment.

The blocking capacitors provide AC coupling of the attenuat-

ed signal levels. The plots in the Typical Performance Char-

acteristics section demonstrate various equalized data rates

using Category 5 UTP at 100 meter lengths. A full schematic

of a recommended driver and receiver circuit for 100Ω Cate-

gory 5 UTP is provided in the Typical Applications section

with further explanation.

10005624

FIGURE 4. Twisted Pair Input Interface

Output Interfacing

The outputs DO and DO produce ECL logic levels when the

recommended output termination networks are used. The DO

and DO pins are not complementary emitter coupled log-

ic outputs. Instead, the outputs are taken off of the collectors

of the transistors. Therefore, care must be taken to meet the

interface threshold levels required by ECL families. Recom-

mended interfaces for standard ECL families are shown in the

following circuits.

DIFFERENTIAL LOAD-TERMINATED OUTPUT

INTERFACE

Figure 5 shows a recommended circuit for implementing a

differential output that is terminated at the load. A diode or

75Ω resistor provides a voltage drop from the positive supply

(+5V for PECL or Ground for ECL operation) to establish

proper ECL levels. The resistors terminate the cable to the

characteristic impedance. The output voltage swing is deter-

mined by the CLC014 output current (10 mA) times the ter-

mination resistor. For the circuit in Figure 5, the nominal

output voltage swing is 750 mV.

10005625

FIGURE 5. Differential Load Terminated

Output Interface

DIFFERENTIAL SOURCE-TERMINATED OUTPUT

INTERFACE

Figure 6 is similar to Figure 5 except that the termination is

provided at the source. This configuration may also be used

for single-ended applications. However, the unused output

must still be terminated as shown.

9 www.national.com

100056 Version 11 Revision 6 Print Date/Time: 2010/08/23 16:48:25

CLC014

10005626

FIGURE 6. Differential Source Terminated

Output Interface

TERMINATING PHYSICALLY SEPARATED OUTPUTS

When the two outputs must be routed to physically separate

locations, the circuit in Figure 6 may be applied. Alternatively,

if load termination is desired, the circuit in Figure 7 may be

used. The resistive divider network provides 75Ω termination

and establishes proper ECL levels. This circuit consumes

slightly more power than the previous circuits.

10005627

FIGURE 7. Alternative Load Terminated

Output Interface

Design Guidelines

SELECTING THE AUTOMATIC EQUALIZER CAPACITOR

The AEC capacitor sets the loop time constant τ for the

equalizer's adaptive loop response time. The following for-

mula is used to set the loop time constant:

τ = R • CAEC • 10 −6

R is a conversion factor that is set by internal equalizer pa-

rameters and cable length. For Belden 8281 coaxial cable,

the R values are (τ = μs, CAEC in pF):

Cable

Length

R Value

(Ohms)

100 meters 15000

200 meters 20000

300 meters 32000

For example, a CAEC value of 100 pF results in an adaptive

loop time constant of 2 μs at 200 meters of cable.

CONNECTION AND OPERATION OF CD AND MUTE

Carrier Detect (CD) is a CMOS output that indicates the

presence of equalized data from the filter. This CD output can

be connected to MUTE to suspend changes in the data out-

puts DO and DO, if no valid signal exists. This simple config-

uration prevents random output transitions due to noise. For

sparse transition patterns it is recommended that a capacitor

be connected to CD as shown in Figure 1.

Add a capacitor to pin 5 to slow the response time of Carrier

Detect when Carrier Detect is connected to MUTE. The ca-

pacitor reduces sensitivity to pathological patterns. Patholog-

ical patterns are defined as sparse data sequences with few

transitions.

OUTPUT EYE MONITOR OEM CONNECTIONS

The OEM is a high-speed, buffered output for monitoring the

equalized eye pattern prior to the output comparator. Its out-

put is designed to drive an AC-coupled 50Ω coaxial cable with

a series 50Ω backmatch resistor. The cable should be termi-

nated with 50Ω at the oscilloscope. Figure 1 shows a

schematic with a typical connection.

MINIMUM DATA TRANSITIONS

The CLC014 specifies a minimum transition rate. For the

CLC014 this sets the minimum data rate for transmitting data

through any cable medium. The CLC014 minimum average

transition density is found in the Electrical Characteristics

section of the datasheet.

POWER SUPPLY OPERATION AND THERMAL

CONSIDERATIONS

The CLC014 operates from either +5V or −5.2V single sup-

plies. Refer to Figure 1 when operating the part from +5V.

When operating with a −5.2V supply, the VEE pins should be

bypassed to ground. The evaluation board and associated

literature provide for operation from either supply.

Maximum power dissipation occurs at minimum cable length.

Under that condition, ICC = 58 mA.

Total power dissipated:

PT = (58 mA)(5V) = 290 mW

Power in the load:

PL = (0.7V)(11 mA) + (37.5)(11 mA)2 = 12 mW

Maximum power dissipated on the die:

PDMAX = PT–PL = 278 mW

Junction Temperature =

(θJA)(278 mW) + TA = T A + 26°C

www.national.com 10

100056 Version 11 Revision 6 Print Date/Time: 2010/08/23 16:48:25

CLC014

Layout and Measurement

The printed circuit board layout for the CLC014 requires prop-

er high-speed layout to achieve the performance specifica-

tions found in the datasheet. The following list contains a few

rules to follow:

1. Use a ground plane.

2. Decouple power pins with 0.1 μF capacitors placed

≤ 0.1” (3mm) from the power pins.

3. Design transmission strip lines from the CLC014's input

and output pins to the board connectors.

4. Route outputs away from inputs.

5. Keep ground plane ≥ 0.025” (0.06mm) away from the

input and output pads.

Figure 8 shows a block level measurement diagram, while

Figure 15 on depicts a detailed schematic. A pseudo-random

pattern generator with low output jitter was used to provide a

NRZI pattern to create the eye diagrams shown in the Typical

Performance Characteristics section.

Since most pattern generators have a 50Ω output impedance,

a translation can be accomplished using a CLC006 Cable

Driver as an impedance transformer. A wide bandwidth os-

cilloscope is needed to observe the high data rate eye pattern.

When monitoring a single output that is terminated at both the

equalizer output and the oscilloscope, the effective output

load is 37.5Ω. Consequently, the signal swing is half that ob-

served for a single-ended 75Ω termination.

10005628

FIGURE 8. Typical Measurement Block

Troubleshooting with scope probes can affect the equaliza-

tion. For high data rates, use a low capacitance probe with

less than 2 pF probe capacitance. Evaluation boards and lit-

erature are available for quick prototyping and evaluation of

the CLC014 Adaptive Cable Equalizer. The CLC014 contains

CMOS devices and operators should use grounding straps

when handling the parts.

Figure 9 shows the CLC014's internal power supply routing.

Bypass VCC (pin 4) by:

•Monolithic capacitor of about 0.1 μF placed less than

0.1” (3mm) from the pin

•Tantalum capacitor of about 6.8 μF for large current signal

swings placed as close as convenient to the CLC014

10005629

FIGURE 9. Power Package Routing Fixture

11 www.national.com

100056 Version 11 Revision 6 Print Date/Time: 2010/08/23 16:48:25

CLC014

To minimize ringing at the CLC014's inputs, place a 100Ω

resistor in series with the input. This resistor reduces induc-

tance effects.

Several layout techniques can improve high speed perfor-

mance:

•Keep input, output and AEC traces well separated

•Use balanced input termination's

•Avoid routing traces close to the CLC014's input trace

•Maintain common return points for components

•Use guard traces

The input lines of the CLC014 use a 100Ω series resistors at

the input pins. This decreases the inductive effects internal to

the part to reduce ringing on fast rise and fall times. Refer to

the evaluation board layout for further suggestions on layout

for the CLC014 Adaptive Equalizer.

EQUALIZATION CURVE

The CLC014 Adaptive Cable Equalizer has a maximum

equalization response as shown in Figure 10. This response

may be obtained by forcing >0.5V differentially at the AEC

pins.

10005630

FIGURE 10. Maximum Equalization Response

CABLE EMULATION BOXES

Some cable emulation boxes will not mimic cables correctly.

When evaluating the CLC014, it is strongly recommended

that actual cable be used to determine the various perfor-

mance parameters.

Typical Applications

COAXIAL CABLE RECEIVER (Page 1)

The CLC014 equalizer application shown on page 1 will

equalize a variety of coaxial cables up to lengths that attenu-

ate the signal by 40 dB at 200 MHz. The application shows

the proper connection for a single cable driven with a CLC006

driver. Carrier Detect (CD) is connected to MUTE to latch

outputs DO and DO in the absence of an input signal to the

equalizer.

Refer to the CLC014's evaluation board layout for additional

suggestions.

National can supply most of the major components required

to design a transmission line repeater. Figure 11 shows a

typical repeater design using the CLC006, CLC014, and the

CLC016. The design functions supported by each chip are:

CLC006: Cable connection chip

Boosts drive for transmission to next repeater or

final destinations

CLC014: Receive serialized digital data from incoming

transmission lines

Equalizes the incoming data

CLC016: Retimes the equalized data (improving jitter)

The CLC016 is a multi-rate data retiming PLL. The circuit

(Figure 11) will work at up to 4 different data rates with no

additional components or manual tuning.

www.national.com 12

100056 Version 11 Revision 6 Print Date/Time: 2010/08/23 16:48:25

CLC014

10005631

FIGURE 11. Typical Repeater Design

DIGITAL VIDEO (SDV) ROUTERS

The CLC014 provides performance that complies with the

SMPTE 259M standard for serial digital video (SDV) trans-

mission over coaxial cable. One common application is in

SDV routers, which provide a switching matrix for connecting

video source equipment (e.g., cameras) to destination equip-

ment (e.g., video tape recorders, monitors, etc.).

Figure 12 shows a typical configuration for an SDV router,

including equalizers, a crosspoint switch, data retimers, and

cable drivers. The CLC014 is used in its standard configura-

tion in this application, and automatically equalizes cable

lengths from zero meters to greater than 300 meters at

360 MHz (see plots in Typical Performance Characteristics

section). The equalized outputs are connected to the differ-

ential inputs of the crosspoint switch. The CLC016 Data Re-

timer receives the data from the crosspoint and performs the

clock and data recovery functions, further reducing jitter. Fi-

nally, the retimed data is driven into the coaxial cable by a

CLC006 Cable Driver (with two amplitude-adjustable outputs)

or a CLC007 Cable Driver (with four outputs).

10005632

FIGURE 12. Video Routing Block Diagram

TWISTED PAIR DRIVER

A low-cost medium for transmitting data is twisted pair. Cat-

egory 5 UTP has an attenuation characteristic similar to

Belden 8281 coaxial cable but scaled in length: 120 meters

of Category 5 UTP is roughly equivalent to 300 meters of

Belden 8281 cable. When properly implemented, the CLC014

will equalize data rates up to 625 Mbps over Category 5 UTP.

The maximum data rate depends upon the cable length. A

plot of Maximum Data Rate vs Cable Length is found in the

Typical Performance Characteristics section for Belden

8281, and can be scaled as stated above to estimate maxi-

mum cable lengths and data rates for UTP.

Category 5 UTP has a characteristic impedance of approxi-

mately 100Ω. The CLC006 in Figure 13 is used to drive the

twisted pair AC-coupled with a series 0.1 μF capacitor and a

50Ω resistor in each differential output. The CLC014 Adaptive

Equalizer requires 800 mVpp from the transmit side of the ca-

13 www.national.com

100056 Version 11 Revision 6 Print Date/Time: 2010/08/23 16:48:25

CLC014

ble. A voltage divider is necessary to scale the voltage to the

required level at the input of the CLC014. This resistor net-

work also provides the correct impedance match for twisted

pair.

For Category 5 UTP, the approximate AEC voltage per length

is 3.75 mV/m (see Block Description). The CLC006 pro-

vides a trim adjust for fine tuning the output signal with the

resistor R. Refer to the CLC006/007 datasheet for tuning di-

rections.

10005633

FIGURE 13. Twisted Pair Equalization

10005634

FIGURE 14. Before and After Equalization at 622 Mbps

Through 50 Meters of Category 5 UTP

10005635

FIGURE 15. Typical Measurement Setup

www.national.com 14

100056 Version 11 Revision 6 Print Date/Time: 2010/08/23 16:48:25

CLC014

Evaluation Board

Evaluation boards are available for a nominal charge that

demonstrate the basic operation of the SDI/SDV/SDH de-

vices. The evaluation boards can be ordered through

National's Distributors. Supplies are limited, please check for

current availability.

The SD014EVK evaluation kit for the CLC014, Adaptive Ca-

ble Equalizer for High-Speed Data Recovery, provides an

operating environment in which the cable equalizer can be

evaluated by system / hardware designers. The evaluation

board has all the needed circuitry and connectors for easy

connection and checkout of the device circuit options as dis-

cussed in the CLC014 datasheet. A schematic, parts list and

pictorial drawing are provided with the board.

From the WWW, the following information may be viewed /

downloaded for most evaluation boards: www.national.com/

appinfo/interface

•Device Datasheet and / or EVK User Manual

•View a picture of the EVK

•View the EVK Schematic

•View the top assembly drawing and BOM

•View the bottom assembly drawing and BOM

PCB LAYOUT

The CLC014 requires proper high-speed layout techniques to

obtain best results. A few recommended layout rules to follow

for best results when using the CLC014 Adaptive Cable

Equalizer are:

1. Use a ground plane.

2. Decouple power pins with 0.01 μF capacitors placed

≤ 0.1” (3mm) from the power pins.

3. Design transmission lines to the inputs and outputs.

4. Route outputs away from inputs.

5. Remove ground plane ≥ 0.025” (0.06mm) from the input

and output pads.

15 www.national.com

100056 Version 11 Revision 6 Print Date/Time: 2010/08/23 16:48:25

CLC014

Physical Dimensions inches (millimeters) unless otherwise noted

14-Pin SOIC

Order Number CLC014AJE

NS Package Number M14A

www.national.com 16

100056 Version 11 Revision 6 Print Date/Time: 2010/08/23 16:48:25

CLC014

Notes

17 www.national.com

100056 Version 11 Revision 6 Print Date/Time: 2010/08/23 16:48:25

CLC014

Notes

CLC014 Adaptive Cable Equalizer for High-Speed Data Recovery

For more National Semiconductor product information and proven design tools, visit the following Web sites at:

www.national.com

Products Design Support

Amplifiers www.national.com/amplifiers WEBENCH® Tools www.national.com/webench

Audio www.national.com/audio App Notes www.national.com/appnotes

Clock and Timing www.national.com/timing Reference Designs www.national.com/refdesigns

Data Converters www.national.com/adc Samples www.national.com/samples

Interface www.national.com/interface Eval Boards www.national.com/evalboards

LVDS www.national.com/lvds Packaging www.national.com/packaging

Power Management www.national.com/power Green Compliance www.national.com/quality/green

Switching Regulators www.national.com/switchers Distributors www.national.com/contacts

LDOs www.national.com/ldo Quality and Reliability www.national.com/quality

LED Lighting www.national.com/led Feedback/Support www.national.com/feedback

Voltage References www.national.com/vref Design Made Easy www.national.com/easy

PowerWise® Solutions www.national.com/powerwise Applications & Markets www.national.com/solutions

Serial Digital Interface (SDI) www.national.com/sdi Mil/Aero www.national.com/milaero

Temperature Sensors www.national.com/tempsensors SolarMagic™ www.national.com/solarmagic

PLL/VCO www.national.com/wireless PowerWise® Design

University

www.national.com/training

THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION

(“NATIONAL”) PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY

OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO

SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS,

IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS

DOCUMENT.

TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT

NATIONAL’S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL

PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR

APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND

APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE

NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS.

EXCEPT AS PROVIDED IN NATIONAL’S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO

LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE

AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR

PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY

RIGHT.

LIFE SUPPORT POLICY

NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR

SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL

COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:

Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and

whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected

to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform

can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness.

National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other

brand or product names may be trademarks or registered trademarks of their respective holders.

For the most current product information visit us at www.national.com

National Semiconductor

Americas Technical

Support Center

Email: support@nsc.com

Tel: 1-800-272-9959

National Semiconductor Europe

Technical Support Center

Email: europe.support@nsc.com

National Semiconductor Asia

Pacific Technical Support Center

Email: ap.support@nsc.com

National Semiconductor Japan

Technical Support Center

Email: jpn.feedback@nsc.com

www.national.com

100056 Version 11 Revision 6 Print Date/Time: 2010/08/23 16:48:25

IMPORTANT NOTICE

Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,

and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should

obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are

sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.

TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard

warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where

mandated by government requirements, testing of all parameters of each product is not necessarily performed.

TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and

applications using TI components. To minimize the risks associated with customer products and applications, customers should provide

adequate design and operating safeguards.

TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,

or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information

published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a

warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual

property of the third party, or a license from TI under the patents or other intellectual property of TI.

Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied

by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive

business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional

restrictions.

Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all

express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not

responsible or liable for any such statements.

TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably

be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing

such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and

acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products

and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be

provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in

such safety-critical applications.

TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are

specifically designated by TI as military-grade or "enhanced plastic."Only products designated by TI as military-grade meet military

specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at

the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.

TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are

designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated

products in automotive applications, TI will not be responsible for any failure to meet such requirements.

Following are URLs where you can obtain information on other Texas Instruments products and application solutions:

Products Applications

Audio www.ti.com/audio Communications and Telecom www.ti.com/communications

Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers

Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps

DLP®Products www.dlp.com Energy and Lighting www.ti.com/energy

DSP dsp.ti.com Industrial www.ti.com/industrial

Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical

Interface interface.ti.com Security www.ti.com/security

Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense

Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive

Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video

RFID www.ti-rfid.com

OMAP Mobile Processors www.ti.com/omap

Wireless Connectivity www.ti.com/wirelessconnectivity

TI E2E Community Home Page e2e.ti.com

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265