Order this document by MC1495/D The MC1495 is designed for use where the output is a linear product of two input voltages. Maximum versatility is assured by allowing the user to select the level shift method. Typical applications include: multiply, divide*, square root*, mean square*, phase detector, frequency doubler, balanced modulator/demodulator, and electronic gain control. * Wide Bandwidth * * * * * LINEAR FOUR-QUADRANT MULTIPLIER Excellent Linearity: 2% max Error on X Input, 4% max Error on Y Input Over Temperature 1% max Error on X Input, 2% max Error on Y Input at + 25C Adjustable Scale Factor, K SEMICONDUCTOR TECHNICAL DATA Excellent Temperature Stability Wide Input Voltage Range: 10 V 15 V Operation *When used with an operational amplifier. 14 1 D SUFFIX PLASTIC PACKAGE CASE 751A (SO-14) MAXIMUM RATINGS (TA = + 25C, unless otherwise noted.) Rating Symbol Value Unit Applied Voltage (V2-V1, V14-V1, V1-V9, V1-V12, V1-V4, V1-V8, V12-V7, V9-V7, V8-V7, V4-V7) V 30 Vdc 14 1 Differential Input Signal V12-V9 V4-V8 (6+I13 RX) (6+I3 RY) Vdc Maximum Bias Current I3 I13 10 10 mA Operating Temperature Range C TA MC1495 MC1495B Storage Temperature Range P SUFFIX PLASTIC PACKAGE CASE 646 0 to +70 - 40 to +125 Tstg - 65 to +150 C ORDERING INFORMATION Device Tested Operating Temperature Range MC1495D MC1495P MC1495BP SO-14 TA = 0 to + 70C TA = - 40 to +125C Motorola, Inc. 1996 MOTOROLA ANALOG IC DEVICE DATA Package Plastic DIP Plastic DIP Rev 0 1 MC1495 ELECTRICAL CHARACTERISTICS (+V = + 32 V , -V = -15 V, TA = + 25C, I3 = I13 = 1.0 mA, RX = RY = 15 k, RL = 11 k, unless otherwise noted.) Characteristics Figure Linearity (Output Error in percent of full scale) TA = + 25C -10 < VX < +10 (VY = 10 V) -10 < VY < +10 (VX = 10 V) TA = TLow to THigh -10 < VX < +10 (VY = 10 V) -10 < VY < +10 (VX = 10 V) Square Mode Error (Accuracy in percent of full scale after Offset and Scale Factor adjustment) TA = + 25C TA = TLow to THigh Scale Factor (Adjustable) 2RL K= 13 RX RY 5 - Input Resistance (f = 20 Hz) Differential Output Resistance (f = 20 Hz) Input Bias Current 5 Symbol Min Typ Max % ERX ERY - - 1.0 2.0 1.0 2.0 ERX ERY ESQ - - 1.5 3.0 2.0 4.0 % - - 0.75 1.0 - - K - 0.1 - 7 RinX RinY - - 30 20 - - M 8 RO - 300 - k Ibx, Iby - - 2.0 2.0 8.0 12 |Iiox|, |Iioy| - - 0.4 0.4 1.0 2.0 - 2.5 - - 10 20 50 100 - 20 - - - - - 3.0 80 750 30 - - - - 10.5 12 - A 6 TA = + 25C TA = TLow to THigh (I + I ) (I + I ) Ibx = 9 12 , Iby = 4 8 2 2 Input Offset Current |I9 - I12| TA = + 25C |I4 - I8| TA = TLow to THigh Average Temperature Coefficient of Input Offset Current TA = TLow to THigh 6 Output Offset Current |I14 - I2| 6 TA = + 25C TA = TLow to THigh Average Temperature Coefficient of Output Offset Current TA = TLow to THigh Frequency Response 3.0 dB Bandwidth, RL = 11 k 3.0 dB Bandwidth, RL = 50 (Transconductance Bandwidth) 3 Relative Phase Shift Between VX and VY 1% Absolute Error Due to Input-Output Phase Shift Common Mode Input Swing (Either Input) 6 6 TA = + 25C TA = TLow to THigh A |TClio| nA/C |IOO| |TCIOO| A nA/C 9,10 BW(3dB) TBW(3dB) f f 11 Common Mode Gain (Either Input) Unit CMV MHz MHz kHz kHz Vdc 11 ACM - 50 - 40 - 60 - 50 - - dB Common Mode Quiescent Output Voltage 12 VO1 VO2 - - 21 21 - - Vdc Differential Output Voltage Swing Capability 9 - 14 - Vpk Power Supply Sensitivity 12 VO S+ S- - - 5.0 10 - - mV/V Power Supply Current 12 I7 - 6.0 7.0 mA 12 PD - 135 170 mW DC Power Dissipation NOTES: 1. THigh = +70C for MC1495 = +125C for MC1495B 2 TLow = 0C for MC1495 = - 40C for MC1495B MOTOROLA ANALOG IC DEVICE DATA MC1495 Figure 1. Multiplier Transfer Characteristic 8.0 + X Y 6.0 KXY 4.0 k= 2.0 10 1 10 A V , GAIN (dB) VO , OUTPUT VOLTAGE (V) Figure 2. Transconductance Bandwidth 20 10 0 - 2.0 0 -10 - 4.0 - 6.0 VY - 20 VX - 8.0 -10 -10 - 8.0 - 6.0 - 4.0 - 2.0 0 2.0 4.0 VX, INPUT VOLTAGE (V) 6.0 8.0 - 30 1.0 10 10 100 f, FREQUENCY (MHz) 1000 Figure 3. Circuit Schematic + 2 14 Output (KXY) 1 - Q5 Y Input 8 4 Q6 Q7 Q8 + - Q2 Q1 + 4.0 k Q3 500 500 500 X Input 12 - 4.0 k 4.0 k 4.0 k 5 6 3 Q4 9 11 10 13 500 500 500 V- 7 This device contains 16 active transistors. Figure 4. Linearity (Using Null Technique) V+ 0.1 F RY = 27 k RX = 7.5 k 10 k VY Es 5 6 VY 10 k 10 11 + VX + - + 10 k MC1495 + 8 40 k 2 2 Offset Adjust See Figure 13 3 7 14 3 5.0 k Scale Factor Adjust 13 10 k 10 k 2 8 6 3 VE MC1741C 1 33 k Output Offset Adjust 7 6 MC1741C 5 12 k 13 k 10 k 8 - 12 10 k 7 3.0 k 9 10 V 3.0 k 1 4 VX 10 k +15 V 3.0 k 5 1 4 4 V- 0.1 F -15 V NOTE: MOTOROLA ANALOG IC DEVICE DATA Adjust "Scale Factor Adjust" for a null in VE.This schematic for illustrative purposes only, not specified for test conditions. 3 MC1495 Figure 5. Linearity (Using X-Y Plotter Technique) RY = 15 k RX = 15 k To Pin 4 or 9 4 VY 6 10 0.1 F - MC1495 2 12 X R1 1 9.1 k RL1 = 11 k 8 Y 32 V 11 + 9 VZ Offset Adjust (See Figures 13 and 14) 5 14 3 I3 7 13 12 k X-Y Plotter Plotter Y-Input VO Plotter X-Input I13 R13 = 13.7 k R3 5.0 k Scale Factor Adjust RL1 = 11 k 0.1 F -15 V Figure 6. Input and Output Current + 32 V RY = 15 k RX = 15 k 5 6 4 10 11 MC1495 I9 8 3 I12 7 5.6 k 0.1 F 14 7 13 5.0 k 0.1 F -15V 4 4 ein = 1.0 Vrms e2 RL = 11 k ein + 1.0 V - e RO = RL 1 -2 e2 10 + 32 V 1 9.1 k 14 11 k 11 k 13 0.1 F 7 3 12 k Scale Factor Adjust 11 2 MC1495 12 0.1 F 13.7 k 5 6 9 50 11 k e1 1.0 Vrms 20 Hz 12 k Scale Factor Adjust -15 V 8 12 3 0.1 F e1 -2 e2 RY = 15 k RX = 15 k 9.1 k 2 - Figure 9. Bandwidth (RL = 11 k) 9 MC1495 + 5.0 k + 32 V 11 1 13.75 k 0.1 F RinX = RinY = R 10 7 13 12 k 12 k RY = 15 k RX = 15 k 8 3 1.0 M Figure 8. Output Resistance 5 6 1 9.1 k 14 11 k 12 1.0 M -15 V 4 11 2 11 k 5.0 k 5.0 k Scale Factor Adjust + 32 V MC1495 8 e2 0.1 F 10 9 e2 I14 I13 = 1.0 mA 12 k I3 = 1.0 mA e1 5 6 4 1.0 M I2 2 13 1.0 M e1 14 I8 12 RY = 15 k RX = 15 k e1 = 1.0 Vrms 20 Hz 9.1 k 1 I4 9 Figure 7. Input Resistance R13 13.7 k 5.0 k 0.1 F eo CL < 3.0 pF -15 V MOTOROLA ANALOG IC DEVICE DATA MC1495 Figure 11. Common Mode Gain and Common Mode Input Swing Figure 10. Bandwidth (RL = 50 ) RY = 510 RX = 510 5 6 4 ein = 1.0 Vrms 10 + 15 V 11 1 2 9 ein 50 MC1495 8 + - 4 + 9 50 3 7 Scale Factor Adjust 0.1 F R13 13.7k 12 k K = 40 5.0 k CMVY (f = 20 Hz) - eo CL < 3.0 pF 0.1F 15 k 5 6 10 12 + 13 15 k 8 50 - 50 14 12 1.0 V 1.0 k CMVX (f = 20 Hz) 13 7 12 k 1.0 mA 5.0 k 11 1 9.1 k 2 + 11 k 14 11 k MC1495 3 50 + 32 V 12 k VO 1.0 mA 0.1 F VO ACM = 20 log CMVY VO or 20 log CMVX 5.0 k -15V 0.1 F -15 V Figure 13. Offset Adjust Circuit Figure 12. Power Supply Sensitivity V+ + 32 V (V+) + 32 V 15 k 5 4 6 15 k 10 R 11 2.0 k 1 9.1 k 2 11 k 9 2.0 k 14 12 6.2 V 4.3 k 3 7 13 13.7 k S+ = 22 k -15 V -15 V (V-) Pot #1 Pot #2 10 k 10 k To Pin 12 X Offset Adjust 11 k 0.1 F VO2 VO1 0.1 F 2N2905A or Equivalent To Pin 8 Y Offset Adjust MC1495 8 S- = V+ 15 V 32 V R 22 k 10 k | (VO1 - VO2)| 2.0 k 10 k -15 V V+ | (VO1 - VO2)| V- Figure 14. Offset Adjust Circuit (Alternate) V+ R 5.1 V To Pin 8 Pot #1 Y Offset Adjust V+ R 15 V 2.0 k Pot #2 10 k 10 k To Pin 12 X Offset Adjust 5.1 V 32 V 2.0 k 5.1 k -15 V MOTOROLA ANALOG IC DEVICE DATA 5 MC1495 Figure 15. Linearity versus Temperature Figure 16. Scale Factor versus Temperature 2.0 0.110 1.6 K, SCALE FACTOR ERX , E RY LINEARITY (%) 1.8 1.4 ERY 1.2 1.0 0.8 ERX 0.6 0.105 K Adjusted to 0.100 at 25C 0.100 0.095 0.4 0.2 0 -55 -25 0 25 50 75 TA , AMBIENT TEMPERATURE (C) 100 -55 125 1.0 ERROR, PERCENT OF FULL SCALE (%) 0.8 0.6 0.4 0.2 0 10 12 14 16 RX or RY (k) 18 0 25 50 75 100 TA , AMBIENT TEMPERATURE (C) 125 Figure 18. Error Contributed by Input Differential Amplifier VX = VY = 10 V Max I3 = I13 = 1.0 mAdc 1.0 VX = VY = 5.0 V Max I3 = I13 = 1.0 mAdc 0.8 0.6 0.4 0.2 0 20 4.0 6.0 8.0 10 RX or RY (k ) 12 14 Figure 19. Maximum Allowable Input Voltage versus Voltage at Pin 1 or Pin 7 14 |VX| or | VY |, MAXIMUM (V pk ) ERROR, PERCENT OF FULL SCALE (%) Figure 17. Error Contributed by Input Differential Amplifier -25 12 10 8.0 Minimum 6.0 4.0 Recommended 2.0 0 0 2.0 4.0 6.0 8.0 10 12 14 16 18 |V1| or |V7| (V) 6 MOTOROLA ANALOG IC DEVICE DATA MC1495 OPERATION AND APPLICATIONS INFORMATION Theory of Operation The MC1495 is a monolithic, four-quadrant multiplier which operates on the principle of variable transconductance. A detailed theory of operation is covered in Application Note AN489, Analysis and Basic Operation of the MC1595. The result of this analysis is that the differential output current of the multiplier is given by: IA - IB = I = 2VXVY RXRYI3 where, IA and IB are the currents into Pins 14 and 2, respectively, and VX and VY are the X and Y input voltages at the multiplier input terminals. DESIGN CONSIDERATIONS General The MC1495 permits the designer to tailor the multiplier to a specific application by proper selection of external components. External components may be selected to optimize a given parameter (e.g. bandwidth) which may in turn restrict another parameter (e.g. maximum output voltage swing). Each important parameter is discussed in detail in the following paragraphs. Linearity, Output Error, ERX or ERY Linearity error is defined as the maximum deviation of output voltage from a straight line transfer function. It is expressed as error in percent of full scale (see figure below). VO +10 V 3 dB Bandwidth and Phase Shift Bandwidth is primarily determined by the load resistors and the stray multiplier output capacitance and/or the operational amplifier used to level shift the output. If wideband operation is desired, low value load resistors and/or a wideband operational amplifier should be used. Stray output capacitance will depend to a large extent on circuit layout. Phase shift in the multiplier circuit results from two sources: phase shift common to both X and Y channels (due to the load resistor-output capacitance pole mentioned above) and relative phase shift between X and Y channels (due to differences in transadmittance in the X and Y channels). If the input to output phase shift is only 0.6, the output product of two sine waves will exhibit a vector error of 1%. A 3 relative phase shift between VX and VY results in a vector error of 5%. Maximum Input Voltage VX(max), VY(max) input voltages must be such that: VX(max) <I13 RY VY(max) <I3 RY Exceeding this value will drive one side of the input amplifier to "cutoff" and cause nonlinear operation. Current I3 and I13 are chosen at a convenient value (observing power dissipation limitation) between 0.5 mA and 2.0 mA, approximately 1.0 mA. Then RX and RY can be determined by considering the input signal handling requirements. For VX(max) = VY(max) = 10 V; VE(max) +10V Vx or Vy For example, if the maximum deviation, VE(max), is 100 mV and the full scale output is 10 V, then the percentage error is: V (max) 100 x 10-3 x 100 = 1.0%. ER = E x 100 = VO(max) 10 Linearity error may be measured by either of the following methods: 1.Using an X-Y plotter with the circuit shown in Figure 5, obtain plots for X and Y similar to the one shown above. 2.Use the circuit of Figure 4. This method nulls the level shifted output of the multiplier with the original input.The peak output of the null operational amplifier will be equal to the error voltage, VE (max). One source of linearity error can arise from large signal nonlinearity in the X and Y input differential amplifiers. To avoid introducing error from this source, the emitter degeneration resistors RX and RY must be chosen large enough so that nonlinear base-emitter voltage variation can be ignored. Figures 17 and 18 show the error expected from this source as a function of the values of RX and RY with an operating current of 1.0 mA in each side of the differential amplifiers (i.e., I3 = I13 = 1.0 mA). MOTOROLA ANALOG IC DEVICE DATA 10 V = 10 k. 1.0 mA 2VX VY The equation IA - IB = RX RY I3 RX = RY > 2VX VY 2kT (RX + ) (RY + qI13 with the assumption RX >> 2kT and RY >> qI13 is derived from IA - IB = 2kT ) I qI3 3 2kT . qI3 At TA = +25C and I13 = I3 = 1.0 mA, 2kT 2kT = = 52 . qI13 qI3 Therefore, with RX = RY = 10 k the above assumption is valid. Reference to Figure 19 will indicate limitations of VX(max) or VY(max) due to V1 and V7. Exceeding these limits will cause saturation or "cutoff" of the input transistors. See Step 4 of General Design Procedure for further details. Maximum Output Voltage Swing The maximum output voltage swing is dependent upon the factors mentioned below and upon the particular circuit being considered. For Figure 20 the maximum output swing is dependent upon V+ for positive swing and upon the voltage at Pin 1 for negative swing. The potential at Pin 1 determines the quiescent level for transistors Q5, Q6, Q7 and Q8. This potential should be related so that negative swing at Pins 2 or 14 does not saturate those transistors. See General Design Procedure for further information regarding selection of these potentials. 7 MC1495 Figure 20. Basic Multiplier GENERAL DESIGN PROCEDURE V+ RX 10 9 VX 5 12 - MC1495 Selection of component values is best demonstrated by the following example. Assume resistive dividers are used at the X and Y-inputs to limit the maximum multiplier input to 5.0 V [VX = VY(max)] for a 10 V input [VX = VY(max)] (see Figure 21). If an overall scale factor of 1/10 is desired, RL 1 RL 2 + + 8 RI 6 + 4 VY 11 RY VO 14 - then, VO = - 3 13 I3 R3 Therefore, K = 4/10 for the multiplier (excluding the divider network). Step 1. The fist step is to select current I3 and current I13. There are no restrictions on the selection of either of these currents except the power dissipation of the device. I3 and I13 will normally be 1.0 mA or 2.0 mA. Further, I3 does not have to be equal to I13, and there is normally no need to make them different. For this example, let VO = K VX VY 2RL K= RX RY I3 7 R13 VX VY (2VX) (2VY) = 4/10 VX VY = 10 10 V- If an operational amplifier is used for level shift, as shown in Figure 21, the output swing (of the multiplier) is greatly reduced. See Section 3 for further details. I3 = I13 = 1.0 mA. Figure 21. Multiplier with Operational Amplifier Level Shift - 15 V - 15 V RY 10 k RX 10 k VY 10 k 10 k 4 10 + VY 11 R1 3.0 k 5 7 6 R0 3.0 k 0.1 F R0 3.0 k 0.1 F 7 1 3 2 + + VX 10 k 9 VX + 3 - 13 I13 I3 R3 -10V VX +10V -10V VY +10V Scale Factor Adjust 2 14 12 P3 RL 5.0 k P4 Y Offset Adjust 2.0 k +15 V 6 P1 10 k VO = -VX VY 10 5 - 1 18 k 5.0 k 5.1 V 8 8 R13 12 k 12 k 4 MC1741C MC1495 10 k +15 V 20 k RL Output Offset Adjust X Offset Adjust P2 10 k 2.0 k -15 V 5.1 V MOTOROLA ANALOG IC DEVICE DATA MC1495 To set currents I3 and I13 to the desired value, it is only necessary to connect a resistor between Pin 13 and ground, and between Pin 3 and ground. From the schematic shown in Figure 3, it can be seen that the resistor values necessary are given by: R13 + 500 = |V-| -0.7 V I13 R3 + 500 = |V-| -0.7 V I3 voltage. It should also be noticed that the collector voltage of transistors Q3 and Q4 is at a potential which is two diode-drops below the voltage at Pin 1. Thus, the voltage at Pin 1 should be about 2.0 V higher than the maximum input voltage. Therefore, to handle +5.0 V at the inputs, the voltage at Pin 1 must be at least +7.0 V. Let V1 = 9.0 Vdc. Since the current flowing into Pin 1 is always equal to 2I3, the voltage at Pin 1 can be set by placing a resistor (R1) from Pin 1 to the positive supply: R1 = Let V- = -15 V, then R13 + 500 = 14.3 V or R13 = 13.8 k 1.0 mA Let R13 = 12 k. Similarly, R3 = 13.8 k, let R3 = 15 k However, for applications which require an accurate scale factor, the adjustment of R3 and consequently, I3, offers a convenient method of making a final trim of the scale factor. For this reason, as shown in Figure 21, resistor R3 is shown as a fixed resistor in series with a potentiometer. For applications not requiring an exact scale factor (balanced modulator, frequency doubler, AGC amplifier, etc.) Pins 3 and 13 can be connected together and a single resistor from Pin 3 to ground can be used. In this case, the single resistor would have a value of 1/2 the above calculated value for R13. Step 2. The next step is to select RX and RY. To insure that the input transistors will always be active, the following conditions should be met: VX < I13, RX VY < I3 RY A good rule of thumb is to make I3RY 1.5 VY(max) and I13 RX 1.5 VX(max). The larger the I3RY and I13RX product in relation to VY and VX respectively, the more accurate the multiplier will be (see Figures 17 and 18). Let V+ = 15 V, then R1 = 4 2RL (2) (RL) 4 = = , or 10 RX RY I3 (10 k) (10 k) (1.0 mA) 10 Thus RL = 20 k. Step 4. To determine what power supply voltage is necessary for this application, attention must be given to the circuit schematic shown in Figure 3. From the circuit schematic it can be seen that in order to maintain transistors Q1, Q2, Q3 and Q4 in an active region when the maximum input voltages are applied (VX = VY = 10 V or VX = 5.0 V, VY = 5.0 V), their respective collector voltage should be at least a few tenths of a volt higher than the maximum input MOTOROLA ANALOG IC DEVICE DATA 15 V -9.0 V (2) (1.0 mA) R1 = 3.0 k. Note that the voltage at the base of transistors Q5, Q6, Q7 and Q8 is one diode-drop below the voltage at Pin 1. Thus, in order that these transistors stay active, the voltage at Pins 2 and 14 should be approximately halfway between the voltage at Pin 1 and the positive supply voltage. For this example, the voltage at Pins 2 and 14 should be approximately 11 V. Step 5. For dc applications, such as the multiply, divide and square-root functions, it is usually desirable to convert the differential output to a single-ended output voltage referenced to ground. The circuit shown in Figure 22 performs this function. It can be shown that the output voltage of this circuit is given by: VO = (I2 -I14) RL And since IA -IB = I2 -I14 = 2IX IY 2VXVY = I3RXRY I3 2RL VX VY where, VX VY is the voltage at 4RX RX I3 the input to the voltage dividers. then VO = Let RX = RY = 10 k, then I3RY = 10 V I13RX = 10 V since VX(max) = VY(max) = 5.0 V, the value of RX= RY = 10 k is sufficient. Step 3. Now that RX, RY and I3 have been chosen, RL can be determined: K= V+ -V1 2I3 Figure 22. Level Shift Circuit V+ I2 I14 RO V2 V14 RL RO + VO - RL The choice of an operational amplifier for this application should have low bias currents, low offset current, and a high common mode input voltage range as well as a high common mode rejection ratio. The MC1456, and MC1741C operational amplifiers meet these requirements. 9 MC1495 The versatility of the MC1495 allows the user to to optimize its performance for various input and output signal levels. Referring to Figure 21, the level shift components will be determined. When VX = VY = 0, the currents I2 and I14 will be equal to I13. In Step 3, RL was found to be 20 k and in Step 4, V2 and V14 were found to be approximately 11 V. From this information RO can be found easily from the following equation (neglecting the operational amplifiers bias current): V2 I = V+ -V2 RL + 13 RO OFFSET AND SCALE FACTOR ADJUSTMENT Offset Voltages Within the monolithic multiplier (Figure 3) transistor baseemitter junctions are typically matched within 1.0 mV and resistors are typically matched within 2%. Even with this careful matching, an output error can occur. This output error is comprised of X-input offset voltage, Y-input offset voltage, and output offset voltage. These errors can be adjusted to zero with the techniques shown in Figure 21. Offset terms can be shown analytically by the transfer function: And for this example, 11 V + 1.0 mA = 15 V -11 V 20 k RO Solving for RO: RO = 2.6 k, thus, select RO = 3.0 k For RO = 3.0 k, the voltage at Pins 2 and 14 is calculated to be: V2 = V14 = 10.4 V. VO = K[Vx Viox Vx(off)] [Vy Vioy Vy(off)] VOO Where: The linearity of this circuit (Figure 21) is likely to be as good or better than the circuit of Figure 5. Further improvements are possible as shown in Figure 23 where RY has been increased substantially to improve the Y linearity, and RX decreased somewhat so as not to materially affect the X linearity. This avoids increasing RL significantly in order to maintain a K of 0.1. K Vx Vy Viox Vioy Vx(off) Vy(off) VOO (1) = scale factor = ``x'' input voltage = ``y'' input voltage = ``x'' input offset voltage = ``y'' input offset voltage = ``x'' input offset adjust voltage = ``y'' input offset adjust voltage = output offset voltage. Figure 23. Multiplier with Improved Linearity - 15 V - 15 V +15 V 7.5 k VY 10 k 4 10 + 11 5 3.0 k 3.0 k 27 k 6 7 3.0 k 7 1 14 - 3 + 4 10 k 6 10 V VX MC1741C MC1495 10 k 10 k 9 + 3 + 13 8 12 k 10 5 - 1 10 k Y Offset Adjust 15 k -VX VY 40 k 33 k 5.0 k Scale Factor Adjust Output Offset Adjust X Offset Adjust 20 k 15 k 20 k 2.0 k 10 2 12 13 k +15 V 2 VO = -15 V 2.0 k MOTOROLA ANALOG IC DEVICE DATA MC1495 X, Y and Output Offset Voltages VO Output Offset VO Vx X Offset DC APPLICATIONS Output Offset Vy Y Offset For most dc applications, all three offset adjust potentiometers (P1, P2, P4) will be necessary. One or more offset adjust potentiometers can be eliminated for ac applications (see Figures 28, 29, 30, 31). If well regulated supply voltages are available, the offset adjust circuit of Figure 13 is recommended. Otherwise, the circuit of Figure 14 will greatly reduce the sensitivity to power supply changes. Scale Factor The scale factor K is set by P3 (Figure 21). P3 varies I3 which inversely controls the scale factor K. It should be noted that current I3 is one-half the current through R1. R1 sets the bias level for Q5, Q6, Q7, and Q8 (see Figure 3). Therefore, to be sure that these devices remain active under all conditions of input and output swing, care should be exercised in adjusting P3 over wide voltage ranges (see General Design Procedure). Adjustment Procedures The following adjustment procedure should be used to null the offsets and set the scale factor for the multiply mode of operation, (see Figure 21). 1. X-Input Offset (a) Connect oscillator (1.0 kHz, 5.0 Vpp sinewave) to the Y-input (Pin 4). (b) Connect X-input (Pin 9) to ground. (c) Adjust X offset potentiometer (P2) for an ac null at the output. 2. Y-Input Offset (a) Connect oscillator (1.0 kHz, 5.0 Vpp sinewave) to the X-input (Pin 9). (b) Connect Y-input (Pin 4) to ground. (c) Adjust Y offset potentiometer (P1) for an ac null at the output. 3. Output Offset (a) Connect both X and Y-inputs to ground. (b) Adjust output offset potentiometer (P4) until the output voltage (VO) is 0 Vdc. 4. Scale Factor (a) Apply +10 Vdc to both the X and Y-inputs. (b) Adjust P3 to achieve + 10 V at the output. 5. Repeat steps 1 through 4 as necessary. Multiply The circuit shown in Figure 21 may be used to multiply signals from dc to 100 kHz. Input levels to the actual multiplier are 5.0 V (max). With resistive voltage dividers the maximum could be very large however, for this application two-to-one dividers have been used so that the maximum input level is 10 V. The maximum output level has also been designed for 10 V (max). Squaring Circuit If the two inputs are tied together, the resultant function is squaring; that is VO = KV2 where K is the scale factor. Note that all error terms can be eliminated with only three adjustment potentiometers, thus eliminating one of the input offset adjustments. Procedures for nulling with adjustments are given as follows: A. AC Procedure: 1. Connect oscillator (1.0 kHz, 15 Vpp) to input. 2. Monitor output at 2.0 kHz with tuned voltmeter and adjust P3 for desired gain. (Be sure to peak response of the voltmeter.) 3. Tune voltmeter to 1.0 kHz and adjust P1 for a minimum output voltage. 4. Ground input and adjust P4 (output offset) for 0 Vdc output. 5. Repeat steps 1 through 4 as necessary. B. DC Procedure: 1. Set VX = VY = 0 V and adjust P4 (output offset potentiometer) such that VO = 0 Vdc 2. Set VX = VY = 1.0 V and adjust P1 (Y-input offset potentiometer) such that the output voltage is + 0.100 V. 3. Set VX = VY = 10 Vdc and adjust P3 such that the output voltage is + 10 V. 4. Set VX = VY = -10 Vdc. Repeat steps 1 through 3 as necessary. Figure 24. Basic Divide Circuit KVX VY I1 X R1 VX I2 VZ - R2 VY + The ability to accurately adjust the MC1495 depends upon the characteristics of potentiometers P1 through P4. Multi-turn, infinite resolution potentiometers with low temperature coefficients are recommended. MOTOROLA ANALOG IC DEVICE DATA 11 MC1495 In terms of percentage error, Divide Circuit Consider the circuit shown in Figure 24 in which the multiplier is placed in the feedback path of an operational amplifier. For this configuration, the operational amplifier will maintain a "virtual ground" at the inverting (-) input. Assuming that the bias current of the operational amplifier is negligible, then I1 = I2 and, KVXVY R1 -VZ = R2 percentage error = or from Equation (5), E R2 E KVX = PED = R1 VZ R1 VZ R2 K VX (1) -R1 VZ Solving for VY, VY = R2 K VX VY = -VZ KVX (3) If R1= KR2, VY = -VZ VX (4) Two things should be emphasized concerning Figure 25. 1. The input voltage (VX) must be greater than zero and must be positive. This insures that the current out of Pin 2 of the multiplier will always be in a direction compatible with the polarity of VZ. 2. Pin 2 and 14 of the multiplier have been interchanged in respect to the operational amplifiers input terminals. In this instance, Figure 25 differs from the circuit connection shown in Figure 21; necessitated to insure negative feedback around the loop. Hence, the output voltage is the ratio of VZ to VX and provides a divide function. This analysis is, of course, the ideal condition. If the multiplier error is taken into account, the output voltage is found to be: VY = - R1 VZ E + R2 K VX KVX (7) From Equation 7, the percentage error is inversely related to voltage VZ (i.e., for increasing values of VZ, the percentage error decreases). A circuit that performs the divide function is shown in Figure 25. (2) If R1=R2, error x 100% actual A suggested adjustment procedure for the divide circuit. 1. Set VZ = 0 V and adjust the output offset potentiometer (P4) until the output voltage (VO) remains at some (not necessarily zero) constant value as VX is varied between +1.0 V and +10 V. 2. Keep VZ at 0 V, set VX at +10 V and adjust the Y input offset potentiometer (P1) until VO = 0 V. 3. Let VX = VZ and adjust the X-input offset potentiometer (P2) until the output voltage remains at some (not necessarily - 10 V) constant value as VZ = VX is varied between +1.0 and +10 V. 4. Keep VX = VZ and adjust the scale factor potentiometer (P3) until the average value of VO is -10 V as VZ = VX is varied between +1.0 V and +10 V. 5. Repeat steps 1 through 4 as necessary to achieve optimum performance. (5) where E is the error voltage at the output of the multiplier. From this equation, it is seen that divide accuracy is strongly dependent upon the accuracy at which the multiplier can be set, particularly at small values of VY. For example, assume that R1 = R2, and K = 1/10. For these conditions the output of the divide circuit is given by: -10 VZ 10 E VY = (6) + VX VX From Equation 6, it is seen that only when VX = 10 V is the error voltage of the divide circuit as low as the error of the multiply circuit. For example, when VX is small, (0.1 V) the error voltage of the divide circuit can be expected to be a hundred times the error of the basic multiplier circuit. Figure 25. Divide Circuit - 15 V RX 10 k 10 k 11 10 4 + RY 10 k 5 - 15 V 3.9 k 7 6 1 - 3.0 k 0.1 F 7 14 3 + 4 10 k 10 k 10 k 9 + + 3 13 8 2 To Offset 5.0 k Adjust (See Figure 13) VO VO = 5 - -10 VZ VX 1 18 k 12 k 12 2 12 13 k 5.0 k P3 Scale Factor Adjust 6 MC1741C MC1495 VX +15 V 0.1 F 3.0 k P4 20 k Output Offset Adjust VZ 0 VX +10 V -10 V VZ +10 V MOTOROLA ANALOG IC DEVICE DATA MC1495 AC APPLICATIONS Figure 26. Basic Square Root Circuit KVO2 VZ + The applications that follow demonstrate the versatility of the monolithic multiplier. If a potted multiplier is used for these cases, the results generally would not be as good because the potted units have circuits that, although they optimize dc multiplication operation, can hinder ac applications. Frequency doubling often is done with a diode where the fundamental plus a series of harmonics are generated. However, extensive filtering is required to obtain the desired harmonic, and the second harmonic obtained under this technique usually is small in magnitude and requires amplification. When a multiplier is used to double frequency the second harmonic is obtained directly, except for a dc term, which can be removed with ac coupling. eo = KE2 cos2 t + MC1495 + - - VO + KVO2 = -VZ or |VZ| VO = K Square Root A special case of the divide circuit in which the two inputs to the multiplier are connected together is the square root function as indicated in Figure 26. This circuit may suffer from latch-up problems similar to those of the divide circuit. Note that only one polarity of input is allowed and diode clamping (see Figure 27) protects against accidental latch-up. This circuit also may be adjusted in the closed-loop mode as follows: 1. Set VZ to -0.01 V and adjust P4 (output offset) for VO = +0.316 V, being careful to approach the output from the positive side to preclude the effect of the output diode clamping. 2. Set VZ to -0.9 V and adjust P2 (X adjust) for VO = +3.0 V. 3. Set VZ to -10 V and adjust P3 (scale factor adjust) for VO = +10 V. 4. Steps 1 through 3 may be repeated as necessary to achieve desired accuracy. 2 eo = KE (1 + cos 2t). 2 A potted multiplier can be used to obtain the double frequency component, but frequency would be limited by its internal level-shift amplififer. In the monolithic units, the amplifier is omitted. In a typical doubler circuit, conventional 15 V supplies are used. An input dynamic range of 5.0 V peak-to-peak is allowed. The circuit generates wave-forms that are double frequency; less than 1% distortion is encountered without filtering. The configuration has been successfully used in excess of 200 kHz; reducing the scale factor by decreasing the load resistors can further expand the bandwidth. Figure 29 represents an application for the monolithic multiplier as a balanced modulator. Here, the audio input signal is 1.6 kHz and the carrier is 40 kHz. Figure 27. Square Root Circuit - 15 V RX 10 k 10 k 4 11 10 + - 15V RY 10 k 3.9 k 5 6 7 1 - 3.0 k 0.1 F 7 2 3 + 4 6 MC1741C MC1495 9 10 k + + 3 13 8 14 P3 To Offset Adjust (See Figure 13) MOTOROLA ANALOG IC DEVICE DATA 5 - VO VO = 10 |VZ| (11 V) 1 13 k 12 k 5.0 k 2 12 13 k Scale Factor Adjust +15 V 0.1 F 3.0 k 5.0 k P4 20 k RL Output Offset Adjust VZ -10 VZ +0 V 13 MC1495 The defining equation for balanced modulation is Figure 28. Frequency Doubler 5 VCC +15 V RX 8.2 k RY 8.2 k 6 10 11 4 E cos t (< 5.0 Vpp) Offset Adjust + 1.0 F - R1 2 3.3 k 9 Y R1 1 3.0 k MC1495 8 12 R1 3.3 k 14 3 6.8 k 13 C1* 7 *Select 2 eo E cos 2 t 20 1.0 F -15 V When two equal cosine waves are applied to X and Y, the result is a wave shape of twice the input frequency. For this example the input was a 10 kHz signal, output was 20 kHz. Figure 29. Balanced Modulator (A) eY = E cos mt eX = E cos ct 4 5 6 10 11 MC1495 12 RL 3.3 k 14 3 13 C1* 7 *Select 6.8 k - 1.0 F + -15 V (B) 14 + 1.0 F - 1 3.0 k RL 2 3.3 k 9 8 Offset Y Adjust X +15 V RX 8.2 k RY 8.2 k eo K(Emcos mt) (Ec cos ct) = KEc Em [ cos (c + m)t + cos (c - m) t ] 2 where c is the carrier frequency, m is the modulator frequency and K is the multiplier gain constant. AC coupling at the output eliminates the need for level translation or an operational amplifier; a higher operating frequency results. A problem common to communications is to extract the intelligence from single-sideband received signal. The ssb signal is of the form: essb = A cos (c + m) t and if multiplied by the appropriate carrier waveform, cos ct, essbecarrier = AK [cos (2c + m)t + cos (c) t ]. 2 If the frequency of the band-limited carrier signal (c) is ascertained in advance, the designer can insert a low pass filter and obtain the (AK/2) (cosct) term with ease. He/she also can use an operational amplifier for a combination level shift-active filter, as an external component. But in potted multipliers, even if the frequency range can be covered, the operational amplifier is inside and not accessible, so the user must accept the level shifting provided, and still add a low pass filter. Amplitude Modulation The multiplier performs amplitude modulation, similar to balanced modulation, when a dc term is added to the modulating signal with the Y-offset adjust potentiometer (see Figure 30). Here, the identity is: Em(1 + m cos mt) Ec cos ct = KEmEccos ct + KEmEcm [ cos(c + m)t + cos (c - m) t ] 2 where m indicates the degrees of modulation. Since m is adjustable, via potentiometer P1, 100% modulation is possible. Without extensive tweaking, 96% modulation may be obtained where c and m are the same as in the balanced modulator example. Linear Gain Control To obtain linear gain control, the designer can feed to one of the two MC1495 inputs a signal that will vary the unit's gain. The following example demonstrates the feasibility of this application. Suppose a 200 kHz sinewave, 1.0 V peak-to-peak, is the signal to which a gain control will be added. The dynamic range of the control voltage VC is 0 V to +1.0 V. These must be ascertained and the proper values of RX and RY can be selected for optimum performance. For the 200 kHz operating frequency, load resistors of 100 were chosen to broaden the operating bandwidth of the multiplier, but gain was sacrificed. It may be made up with an amplifier operating at the appropriate frequency (see Figure 31). MOTOROLA ANALOG IC DEVICE DATA MC1495 Figure 30. Amplitude Modulation 5 eY = E cos mt 4 eX = E cos mt 9 % Modulation Adjust Offset Adjust VCC = +15 V RX 8.2 k RY 8.2 k 6 10 R1 1 3.0 k 11 RL1 2 3.3 k MC1495 Y 8 X 12 RL1 3.3 k 14 3 13 C1* 7 *Select eX, eY < 5.0 Vpp 6.8 k 1.0 F eo -15 V The signal is applied to the unit's Y-input. Since the total input range is limited to 1.0 Vpp, a 2.0 V swing, a current source of 2.0 mA and an RY value of 1.0 k is chosen. This takes best advantage of the dynamic range and insures linear operation in the Y-channel. Since the X-input varies between 0 and +1.0 V, the current source selected was 1.0 mA, and the RX value chosen was 2.0 k. This also insures linear operation over the X-input dynamic range. Choosing RL = 100 assures wide bandwidth operation. Hence, the scale factor for this configuration is: K= RL RX RY I3 = 100 V-1 (2 k) (1 k) (2 x 103) = 1 -1 V 40 The 2 in the numerator of the equation is missing in this scale factor expression because the output is single-ended and ac coupled. Figure 31. Linear Gain Control 2.0 k 10 11 +12 V 1.0 k 5 6 Y Vin 4 1.25 1.0 1 1.5 k + VC X 1.0 k 0.1 F Offset Adjust 9 Y 8 X 12 MC1495 1 k = 40 + V O (Vpp ) 51 2 Vin = 1.0 Vpp 200 kHz 100 0.75 0.5 100 - 0.25 14 - 3 13 Amplifier AV = 40 7 VO 0 0 2.0 mA 0.2 0.4 0.6 0.8 VAGC (V) 1.0 1.2 3.0 k 11 k 5.0 k 1.0 F + P3 NOTE: Linear gain control of a 1.0 Vpp signal is performed with a 0 V to 1.0 V control voltage. If VC is 0.5 V the output will be 0.5 Vpp. -12 V MOTOROLA ANALOG IC DEVICE DATA 15 MC1495 OUTLINE DIMENSIONS D SUFFIX PLASTIC PACKAGE CASE 751A-03 ISSUE F NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. -A- 14 8 -B- 1 P 7 PL 0.25 (0.010) 7 G M B M R X 45 _ C F -T- D 14 PL 0.25 (0.010) SEATING PLANE M J M K T B S A S P SUFFIX PLASTIC PACKAGE CASE 646-06 ISSUE L 14 8 1 7 B A F L C J N H G D SEATING PLANE DIM A B C D F G J K M P R K M MILLIMETERS MIN MAX 8.55 8.75 3.80 4.00 1.35 1.75 0.35 0.49 0.40 1.25 1.27 BSC 0.19 0.25 0.10 0.25 0_ 7_ 5.80 6.20 0.25 0.50 INCHES MIN MAX 0.337 0.344 0.150 0.157 0.054 0.068 0.014 0.019 0.016 0.049 0.050 BSC 0.008 0.009 0.004 0.009 0_ 7_ 0.228 0.244 0.010 0.019 NOTES: 1. LEADS WITHIN 0.13 (0.005) RADIUS OF TRUE POSITION AT SEATING PLANE AT MAXIMUM MATERIAL CONDITION. 2. DIMENSION L TO CENTER OF LEADS WHEN FORMED PARALLEL. 3. DIMENSION B DOES NOT INCLUDE MOLD FLASH. 4. ROUNDED CORNERS OPTIONAL. DIM A B C D F G H J K L M N INCHES MIN MAX 0.715 0.770 0.240 0.260 0.145 0.185 0.015 0.021 0.040 0.070 0.100 BSC 0.052 0.095 0.008 0.015 0.115 0.135 0.300 BSC 0_ 10_ 0.015 0.039 MILLIMETERS MIN MAX 18.16 19.56 6.10 6.60 3.69 4.69 0.38 0.53 1.02 1.78 2.54 BSC 1.32 2.41 0.20 0.38 2.92 3.43 7.62 BSC 0_ 10_ 0.39 1.01 Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. How to reach us: USA / EUROPE / Locations Not Listed: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036. 1-800-441-2447 or 602-303-5454 JAPAN: Nippon Motorola Ltd.; Tatsumi-SPD-JLDC, 6F Seibu-Butsuryu-Center, 3-14-2 Tatsumi Koto-Ku, Tokyo 135, Japan. 03-81-3521-8315 MFAX: RMFAX0@email.sps.mot.com - TOUCHTONE 602-244-6609 INTERNET: http://Design-NET.com ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852-26629298 16 *MC1495/D* MOTOROLA ANALOG IC DEVICE DATA MC1495/D