www.vishay.com
21
Models M83401/04, 05, 06, 07, 08, 09; C & G Schematics
Vishay Techno
Document Number 68014
Revision 23-Sep-99
FEATURES
•0.36 watt to 1.8 watt at + 70°C.
•Qualified to MIL-PRF-83401.
•Designed for automatic insertion.
•Withstands thermal stress from - 65°C to + 125°C.
•Conforms to IC package configurations.
•High temperature solder joints.
•Custom schematic MIL-equivalent available.
QPL MIL-PRF-83401 Qualified, Single-In-Line
Resistor Networks
Standard Profile Low Profile
6 pin (M8340104xxxxxxG) 6 pin (M8340107xxxxxxG)
8 pin (M8340105xxxxxxG) 8 pin (M8340108xxxxxxG)
10 pin (M8340106xxxxxxG) 10 pin (M8340109xxxxxxG)
3, 4 or 5 isolated resistors
This model provides the user with a choice of 3, 4 or 5 nominally equal resistors.
Each resistor is isolated from all others. Commonly used in the following
applications:
•“Wired OR” Pull-up •Long-line Impedance Balancing
•Power Driven Pull-up •LED Current Limiting
•Power Gate Pull-up •ECL Output Pull-down
•Line Termination •TTL Input Pull-down
6 Pin
Pin #1 8 Pin
10 Pin
Standard Profile Low Profile
6 pin (M8340104xxxxxxC) 6 pin (M8340107xxxxxxC)
8 pin (M8340105xxxxxxC) 8 pin (M8340108xxxxxxC)
10 pin (M8340106xxxxxxC) 10 pin (M8340109xxxxxxC)
5, 7 or 9 resistors with one pin common
This model provides the user with a choice of 5, 7 or 9 nominally equal resistors,
each connected to a common pin (Pin No.1). Commonly used in the following
applications:
•“Wired OR” Pull-up •Open Collector Pull-up
•Power Gate Pull-up •TTL Input Pull-down
•MOS/ROM Pull-up/Pull-down •TTL Unused Gate Pull-up
6 Pin
8 Pin
10 Pin
Pin #1
CIRCUIT APPLICATIONS
C Schematic
G Schematic
ELECTRICAL SPECIFICATIONS
Resistance Range: 100 ohms to 1 Megohm standard profile,
27 ohms to 1 Megohm low profile.
Resistance T olerance: ± 1%, ± 2%, ± 5% standard. Tighter
tolerances available.
Temperature Coefficient: (- 55°C to + 125°C)
“K” = ± 100PPM/°C, “M” = ± 300PPM/°C.
Package Power Rating:
Schematic Standard Profile Low Profile
C 1.0 watt to 1.8 watt 0.6 watt to 1.08 watt
G 0.6 watt to 1.0 watt 0.36 watt to 0.60 watt
Maximum Operating Voltage: 50 volts per resistor.
Dielectric Strength: 200 V RMS, 1 minute.
Insulation Resistance: 10,000 Megohm minimum.
MECHANICAL SPECIFICATIONS
Resistive Element: Thick film.
Encapsulation: Thermoset epoxy mold.
Terminals: Solderable leads.
Terminal Strength: 4.5 pounds applied to 5 terminals for
30 seconds.
Solderability: Meets MIL-STD-202, Method 208.
ENVIRONMENTAL SPECIFICATIONS
Temperature Limits: - 65°C to + 125°C.
www.vishay.com
22
Models M83401/04, 05, 06, 07, 08, 09; C & G Schematics
Vishay Techno
Document Number 68014
Revision 23-Sep-99
MIL-PRF-83401
REQUIREMENT
Group A Combined
∆R ≤ 0.70%
∆R ≤ 0.50%
∆R ≤ 0.25%
∆R ≤ 0.25%
∆R ≤ 0.25%
∆R ≤ 0.25%
∆R ≤ 0.50%
∆R ≤ 0.25%
∆R ≤ 0.25%
∆R ≤ 0.25%
∆R ≤ 0.50%
TYPICAL ∆R
∆R < 0.10%
∆R < 0.10%
∆R < 0.02%
∆R < 0.02%
∆R < 0.02%
∆R < 0.06%
∆R < 0.20%
∆R < 0.05%
∆R < 0.04%
∆R < 0.04%
∆R < 0.20%
TEST1
Power Conditioning (108)
Thermal Shock (107)
Thermal Shock Group C (107)
Short Time Overload
Low Temperature Storage
Low Temperature Operation
High T emperature Exposure
Moisture Resistance (106)
Resistance to Soldering Heat (210)
Shock (213)
Vibration (204)
Load Life (108)
CONDITIONS
100 hours at 1.5 times rated power at + 25°C
5 cycles, - 65°C to + 125°C
25 cycles, - 65°C to + 125°C
2.5 times rated voltage not to exceed 2 times rated power
for 5 seconds
24 hours, no load at - 65°C
1 hour storage, 45 minutes rated power at - 65°C
100 hours, no load at + 125°C
240 hours with humidity ranging from 80% RH to 98% RH
+ 260°C for 10 seconds
18 shocks, 100g, 6 ms, sawtooth, 3 axes
10 to 2000Hz, 20g, 12 hours, 3 axes
1000 hours at rated power at + 70°C and at rated power
at + 25°C
1Numbers in parenthesis refer to test method MIL-STD-202 as modified by the detail specification.
ENVIRONMENTAL PERFORMANCE
6, 8, 10 Pin Low Profile
DIMENSIONAL CONFIGURATIONS [Numbers in brackets indicate millimeters]
6, 8, 10 Pin Standard Profile
.010 ± .002
[.254 ± .051]
.083 ± .005
[2.11 ± .127] .590 ± .008
[14.99 ± .203]
.790 ± .008
[20.07 ± .203]
.018 ± .003
[.457 ± .076]
.135 ± .010
[3.43 ± .254]
.040 + .009
- .015
[1.02 + .229
- .381]
.020 ± .003
[.508 ± .076]
.990 ± .008
[25.15 ± .203]
.100 ± .005
[2.54 ± .127]
Non-Cumulative
.338 ± .005
[8.59 ± .127]
Pin #1
Identifier
.010 ± .002
[.254 ± .051]
.083 ± .005
[2.11 ± .127]
.040 + .009
- .015
[1.02 + .229
- .381]
.135 ± .010
[3.43 ± .254]
.187 ± .005
[4.75 ± .127]
.020 ± .003
[.508 ± .076]
.100 ± .005
[2.54 ± .127]
Non-Cumulative
.590 ± .008
[14.99 ± .203]
.790 ± .008
[20.07 ± .203]
.990 ± .008
[25.15 ± .203]
.018 ± .003
[.457 ± .076] Pin #1
Identifier
www.vishay.com
23
Models M83401/04, 05, 06, 07, 08, 09; C & G Schematics
Vishay Techno
Document Number 68014
Revision 23-Sep-99
DERATING
The power rating listed for each network is based on
continuous full-load operation at an ambient temperature of
+ 70°C. When the network is operated at temperatures other
than + 70°C, the power rating should be scaled linearly as shown.
POWER RATING
% OF RATED WATTAGE
130
110
90
70
50
30
AMBIENT TEMP. DEG. CENTIGRADE
- 60 - 30 0 30 60 90 120 150
70
25
HOW TO ORDER - MILITARY PART NUMBER
M83401
MILITARY SPECIFICATION
NUMBER
C
SCHEMATIC
EXAMPLE: M8340106M1003FC = A single-in-line resistor network with 10 pins, a standard profile, a TCR of ± 300PPM/°C, resistance
value of 100 kilohms, tolerance of ± 1% and to Schematic C.
K
CHARACTERISTIC
K= ±100PPM/°C
M= ±300PPM/°CFirst three digits are
significant figures. Last
digit specifies number
of zeros to follow. Use
R as decimal point for
value less than 100 ohms.
Example: 30R0 = 30 Ohms.
1003
VALUE F
TOLERANCE
F=± 1%
G=± 2%
J=± 5%
06
SIZE
04 = 6 Pin Standard Profile SIP
05 = 8 Pin Standard Profile SIP
06 = 10 Pin Standard Profile SIP
07 = 6 Pin Low Profile SIP
08 = 8 Pin Low Profile SIP
09 = 10 Pin Low Profile SIP
C = Common
Bus
G = Isolated
