54ACTQ543 Quiet Series Octal Registered Transceiver with TRI-STATE (R) Outputs General Description Features The ACTQ543 is a non-inverting octal transceiver containing two sets of D-type registers for temporary storage of data flowing in either direction. Separate Latch Enable and Output Enable inputs are provided for each register to permit independent input and output control in either direction of data flow. The ACTQ utilizes NSC Quiet Series technology to guarantee quiet output switching and improved dynamic threshold performance. FACT Quiet SeriesTM features GTOTM output control and undershoot corrector in addition to a split ground bus for superior performance. n Guaranteed simultaneous switching noise level and dynamic threshold performance n 8-bit octal latched transceiver n Separate controls for data flow in each direction n Back-to-back registers for storage n Outputs source/sink 24 mA n 4 kV minimum ESD immunity Ordering Code Military Package Number Package Description 54ACTQ543DMQB J24A 24-Lead Ceramic Dual-In-Line 54ACTQ543FMQB W24C 24-Lead Cerpack 54ACTQ543LMQB E28A 24-Lead Ceramic Leadless Chip Carrier, Type C Logic Symbols IEEE/IEC DS100233-1 DS100233-4 GTOTM is a trademark of National Semiconductor Corporation. TRI-STATE (R) is a registered trademark of National Semiconductor Corporation. FACT (R) is a registered trademark of Fairchild Semiconductor Corporation. FACT Quiet SeriesTM is a trademark of Fairchild Semiconductor Corporation. (c) 1998 National Semiconductor Corporation DS100233 www.national.com 54ACTQ543 Quiet Series Octal Registered Transceiver with TRI-STATE Outputs August 1998 Connection Diagrams Pin Names Pin Assignment for DIP and Flatpak Description OEAB A-to-B Output Enable Input (Active LOW) OEBA B-to-A Output Enable Input (Active LOW) CEAB A-to-B Enable Input (Active LOW) CEBA B-to-A Enable Input (Active LOW) LEAB A-to-B Latch Enable Input (Active LOW) LEBA B-to-A Latch Enable Input (Active LOW) A0-A7 A-to-B Data Inputs or B-to-A TRI-STATE Outputs B0-B7 B-to-A Data Inputs or A-to-B TRI-STATE Outputs Functional Description The ACTQ543 contains two sets of eight D-type latches, with separate input and output controls for each set. For data flow from A to B, for example, the A-to-B Enable (CEAB) input must be LOW in order to enter data from A0-A7 or take data from B0-B7, as indicated in the Data I/O Control Table. With CEAB LOW, a LOW signal on the A-to-B Latch Enable (LEAB) input makes the A-to-B latches transparent; a subsequent LOW-to-HIGH transition of the LEAB signal puts the A latches in the storage mode and their outputs no longer change with the A inputs. With CEAB and OEAB both LOW, the TRI-STATE B output buffers are active and reflect the data present at the output of the A latches. Control of data flow from B to A is similar, but using the CEBA, LEBA and OEBA inputs. DS100233-2 Pin Assignment for LCC Data I/O Control Table Inputs DS100233-3 Latch Status Output Buffers CEAB LEAB OEAB H X X Latched High Z X H X Latched -- L L X Transparent -- X X H -- High Z L X L -- Driving H = HIGH Voltage Level L = LOW Voltage Level X = Immaterial A-to-B data flow shown; B-to-A flow control is the same, except using CEBA, LEBA and OEBA www.national.com 2 Logic Diagram DS100233-8 Please note that this diagram is provided only for the understanding of logic operations and should not be used to estimate propagation delays. 3 www.national.com Absolute Maximum Ratings (Note 1) DC Latch-up Source or Sink Current Junction Temperature (TJ) CDIP If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Supply Voltage (VCC) DC Input Diode Current (IIK) VI = -0.5V VI = VCC + 0.5V DC Input Voltage (VI) DC Output Diode Current (IOK) VO = -0.5V VO = VCC + 0.5V DC Output Voltage (VO) DC Output Source or Sink Current (IO) DC VCC or Ground Current per Output Pin (ICC or IGND) Storage Temperature (TSTG) -0.5V to +7.0V 300 mA 175C Recommended Operating Conditions -20 mA +20 mA -0.5V to VCC + 0.5V Supply Voltage VCC 'ACTQ Input Voltage (VI) Output Voltage (VO) Operating Temperature (TA) (Note 2) 54ACTQ Minimum Input Edge Rate V/t 'ACTQ Devices VIN from 0.8V to 2.0V VCC @ 4.5V, 5.5V -20 mA +20 mA -0.5V to VCC + 0.5V 50 mA 50 mA -65C to +150C 4.5V to 5.5V 0V to VCC 0V to VCC -55C to +125C 125 mV/ns Note 1: Absolute maximum ratings are those values beyond which damage to the device may occur. The databook specifications should be met, without exception, to ensure that the system design is reliable over its power supply, temperature, and output/input loading variables. National does not recommend operation of FACT (R) circuits outside databook specifications. Note 2: All commercial packaging is not recommended for applications requiring greater than 2000 temperature cycles from -40C to +125C. DC Characteristics for 'ACTQ Family Devices Symbol Parameter VCC 54ACTQ TA = (V) -55C to +125C Units Conditions Guaranteed Limits VIH VIL VOH Minimum High Level 4.5 2.0 Input Voltage 5.5 2.0 Maximum Low Level 4.5 0.8 Input Voltage 5.5 0.8 Minimum High Level 4.5 4.4 Output Voltage 5.5 5.4 V VOUT = 0.1V V or VCC - 0.1V VOUT = 0.1V V or VCC - 0.1V IOUT = -50 A (Note 3) VIN = VIL or VIH VOL 4.5 3.70 5.5 4.70 Maximum Low Level 4.5 0.1 Output Voltage 5.5 0.1 V IOH = -24 mA V IOH = -24 mA IOUT = 50 A (Note 3) VIN = VIL or VIH IIN Maximum Input 4.5 0.50 5.5 0.50 V IOL = 24 mA 1.0 A IOL = 24 mA VI = VCC, GND 5.5 5.5 10 A 1.6 mA V(OE) = VIL, VIH VO = VCC, GND VI = VCC - 2.1V mA VOLD = 1.65V Max Leakage Current IOZT Maximum I/O Leakage Current ICCT Maximum ICC/Input 5.5 IOLD 5.5 IOHD Minimum Dynamic Output Current (Note 4) ICC Maximum Quiescent 5.5 -50 mA VOHD = 3.85V Min 5.5 160.0 A VIN = VCC Supply Current www.national.com or GND (Note 5) 4 DC Characteristics for 'ACTQ Family Devices Symbol Parameter (Continued) VCC 54ACTQ TA = (V) -55C to +125C Units Conditions Guaranteed Limits VOLP Quiet Output 5.0 1.5 V (Notes 6, 7) 5.0 -1.2 V (Notes 6, 7) Maximum Dynamic VOL VOLV Quiet Output Minimum Dynamic VOL Note 3: Maximum of 8 outputs loaded; thresholds on input associated with output under test. Note 4: Maximum test duration 2.0 ms, one output loaded at a time. Note 5: ICC for 54ACTQ @ 25C is identical to 74ACTQ@ 25C. Note 6: Plastic DIP package. Note 7: Max number of outputs defined as (n). (n-1) Data Inputs are driven 0V to 3V, one output @ GND. Note 8: Max number of Data Inputs (n) switching. (n-1) Inputs switching 0V to 3V ('ACTQ). Input-under-test switching: 3V to threshold (VILD), 0V to threshold (VIHD), f = 1 MHz. AC Electrical Characteristics Symbol Parameter tPLH Propagation Delay tPHL Transparent Mode 54ACTQ TA = -55C VCC (V) (Note 9) to +125C CL = 50 pF Units Fig. No. Figure 4 Min Max 5.0 2.0 9.5 ns 5.0 2.0 11.0 ns 5.0 1.5 13.0 ns 5.0 1.5 9.0 ns An to Bn or Bn to An tPLH Propagation Delay tPHL LEBA, LEAB Figure 4 to An, Bn tPZH tPZL Figure 6 Output Enable Time OEBA or OEAB to An or Bn CEBA or CEAB to An or Bn tPHZ Output Disable Time tPLZ OEBA or OEAB to An or Bn Figure 6 CEBA or CEAB to An or Bn Note 9: Voltage Range 5.0 is 5.0V 0.5V AC Operating Requirements 54ACTQ TA = -55C Symbol ts Parameter Setup Time, HIGH or LOW to +125C CL = 50 pF VCC (V) (Note 10) Units Fig. No. Guaranteed Minimum 5.0 3.0 ns Figure 7 5.0 1.5 ns Figure 7 5.0 4.0 ns Figure 5 An or Bn to LEBA or LEAB th Hold Time, HIGH or LOW An or Bn to LEBA or LEAB tw Latch Enable Pulse Width, LOW Note 10: Voltage Range 5.0 is 5.0V 0.5V 5 www.national.com Capacitance Symbol Parameter CIN CPD Typ Units Input Capacitance 4.5 pF Power Dissipation 70.0 pF Conditions VCC = OPEN VCC = 5.0V Capacitance AC Loading AC Waveforms DS100233-12 FIGURE 4. Propagation Delay Waveforms for Inverting and Non-Inverting Functions DS100233-10 *Includes jig and probe capacitance FIGURE 1. Standard AC Test Load DS100233-13 DS100233-11 FIGURE 5. Propagation Delay, Pulse Width Waveforms FIGURE 2. Test Input Signal Levels Amplitude Rep. Rate tw tr tf 3.0V 1 MHz 500 ns 2.5 ns 2.5 ns FIGURE 3. Test Input Signal Requirements DS100233-14 FIGURE 6. TRI-STATE Output High and Low Enable and Disable Time www.national.com 6 AC Waveforms (Continued) DS100233-15 FIGURE 7. Setup Time, Hold Time and Recovery Time Waveforms 7 www.national.com 8 Physical Dimensions inches (millimeters) unless otherwise noted 28-Terminal Ceramic Leadless Chip Carrier (L) NS Package Number E28A 24-Lead Ceramic Dual-In-Line Package (D) NS Package Number J24F 9 www.national.com 54ACTQ543 Quiet Series Octal Registered Transceiver with TRI-STATE Outputs Physical Dimensions inches (millimeters) unless otherwise noted (Continued) 24-Lead Ceramic Flatpak (F) NS Package Number W24C LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 2. A critical component in any component of a life support 1. Life support devices or systems are devices or sysdevice or system whose failure to perform can be reatems which, (a) are intended for surgical implant into sonably expected to cause the failure of the life support the body, or (b) support or sustain life, and whose faildevice or system, or to affect its safety or effectiveness. ure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. National Semiconductor Corporation Americas Tel: 1-800-272-9959 Fax: 1-800-737-7018 Email: support@nsc.com www.national.com National Semiconductor Europe Fax: +49 (0) 1 80-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 1 80-530 85 85 English Tel: +49 (0) 1 80-532 78 32 Francais Tel: +49 (0) 1 80-532 93 58 Italiano Tel: +49 (0) 1 80-534 16 80 National Semiconductor Asia Pacific Customer Response Group Tel: 65-2544466 Fax: 65-2504466 Email: sea.support@nsc.com National Semiconductor Japan Ltd. Tel: 81-3-5620-6175 Fax: 81-3-5620-6179 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.