SN75C189, SN75C189A QUADRUPLE LOW-POWER LINE RECEIVERS SLLS041G - OCTOBER 1988 - REVISED JANUARY 2000 D D D D D D D D Meet or Exceed the Requirements of TIA/EIA-232-F and ITU Recommendation V.28 Low Supply Current . . . 420 A Typ Preset On-Chip Input Noise Filter Built-in Input Hysteresis Response and Threshold Control Inputs Push-Pull Outputs Functionally Interchangeable and Pin-to-Pin Compatible With Texas Instruments SN75189/SN75189A and Motorola MC1489/MC1489A Package Options Include Plastic Small-Outline (D) and Shrink Small-Outline (DB) Packages, and Standard Plastic (N) DIP D, DB, OR N PACKAGE (TOP VIEW) 1A 1 CONT 1Y 2A 2 CONT 2Y GND 1 14 2 13 3 12 4 11 5 10 6 9 7 8 VCC 4A 4 CONT 4Y 3A 3 CONT 3Y description The SN75C189 and SN75C189A are low-power, bipolar, quadruple line receivers that are used to interface data terminal equipment (DTE) with data circuit-terminating equipment (DCE). These devices have been designed to conform to TIA/EIA-232-F. The SN75C189 has a 0.33-V typical hysteresis, compared with 0.97 V for the SN75C189A. Each receiver has provision for adjustment of the overall input threshold levels. This is achieved by choosing external series resistors and voltages to provide bias levels for the response-control pins. The output is in the high logic state if the input is open circuit or shorted to ground. These devices have an on-chip filter that rejects input pulses of less than 1-s duration. An external capacitor can be connected from the control pins to ground to provide further input noise filtering for each receiver. The SN75C189 and SN75C189A have been designed using low-power techniques in a bipolar technology. In most applications, these receivers interface to single inputs of peripheral devices such as UARTs, ACEs, or microprocessors. By using sampling, such peripheral devices usually are insensitive to the transition times of the input signals. If this is not the case, or for other uses, it is recommended that the SN75C189 and SN75C189A outputs be buffered by single Schmitt input gates or single gates of the HCMOS, ALS, or 74F logic families. The SN75C189 and SN75C189A are characterized for operation from 0C to 70C. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Copyright 2000, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 1 SN75C189, SN75C189A QUADRUPLE LOW-POWER LINE RECEIVERS SLLS041G - OCTOBER 1988 - REVISED JANUARY 2000 logic symbol 1A 1 CONT 2A 2 CONT 3A 3 CONT 4A 4 CONT logic diagram (each receiver) 1 A 2 Response Control 3 THRESHOLD ADJUST 4 5 6 10 8 9 1Y Y 2Y 3Y 13 11 12 4Y This symbol is in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12. schematic of inputs and outputs EQUIVALENT OF EACH INPUT EQUIVALENT OF EACH OUTPUT VCC Input ESD Protection 3.4 k ESD Protection Response Control Output 1.5 k 530 All resistor values shown are nominal. absolute maximum ratings over operating free-air temperature range (unless otherwise noted) Supply voltage, VCC (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V Input voltage range, VI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -30 V to 30 V Output voltage range, VO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 V to VCC+ 0.3 V Package thermal impedance, JA (see Note 2): D package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86C/W DB package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96C/W N package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80C/W Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260C Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -65C to 150C Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. All voltages are with respect to network GND. 2. The package thermal impedance is calculated in accordance with JESD 51. 2 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SN75C189, SN75C189A QUADRUPLE LOW-POWER LINE RECEIVERS SLLS041G - OCTOBER 1988 - REVISED JANUARY 2000 recommended operating conditions MIN NOM MAX VCC VI Supply voltage 4.5 5 6 Input voltage (see Note 3) -25 IOH IOL High-level output current -3.2 mA Low-level output current 3.2 mA Response-control current 1 mA 25 UNIT V V TA Operating free-air temperature 0 70 C NOTE 3: The algebraic convention, where the more positive (less negative) limit is designated as maximum, is used in this data sheet for logic levels only, e.g., if -10 V is a maximum, the typical value is a more negative voltage. electrical characteristics over recommended free-air temperature range, VCC = 5 V 10% (unless otherwise noted) (see Note 4) PARAMETER VIT IT+ Positive going input threshold voltage Positive-going VIT IT- Negative going input threshold voltage Negative-going Vh hys Input hysteresis voltage (VIT IT+ - VIT IT-) VOH TEST CONDITIONS 'C189 'C189A 'C189 'C189A 'C189 'C189A High level output voltage High-level See Figure 1 MIN TYP 1 1.5 1.6 2.25 0.75 See Figure 1 See Figure 1 MAX 1.25 0.75 1 0.15 0.33 0.65 0.97 VCC = 4.5 V to 6 V,, IOH = -20 A VI = 0.75 V,, 35 3.5 VCC = 4.5 V to 6 V, IOH = -3.2 mA VI = 0.75 V, 2.5 VI = 3 V,, 1.25 UNIT V V V V VOL Low level output voltage Low-level VCC = 4.5 V to 6 V,, IOL = 3.2 mA IIH High level input current High-level See Figure 2 VI = 25 V VI = 3 V 3.6 8.3 0.43 1 IIL Low level input current Low-level See Figure 2 VI = -25 V VI = -3 V -3.6 -8.3 -0.43 -1 IOS Short-circuit output current See Figure 3 ICC Supply current VI = 5 V, See Figure 2 04 0.4 No load, V mA mA -35 mA 420 700 A TYP MAX UNIT All typical values are at TA = 25C. NOTE 4: All characteristics are measured with response-control terminal open. switching characteristics, VCC = 5 V 10%, TA = 25C PARAMETER tPLH tPHL tTLH tTHL TEST CONDITIONS MIN Propagation delay time, low- to high-level output 6 s Propagation delay time, high- to low-level output Transition time, low- to high-level output 6 s 500 ns 300 ns RL = 5 k, CL = 50 pF, Transition time, high- to low-level output See Figure 4 tw(N) Duration of longest pulse rejected as noise 1 6 s Measured between 10% and 90% points of output waveform The receiver ignores any positive- or negative-going pulse that is less than the minimum value of tw(N) and accepts any postive- or negative-going pulse greater than the maximum of tw(N). POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 3 SN75C189, SN75C189A QUADRUPLE LOW-POWER LINE RECEIVERS SLLS041G - OCTOBER 1988 - REVISED JANUARY 2000 PARAMETER MEASUREMENT INFORMATION VCC III II III II VIT, V1 VOH Response Control Open Unless Otherwise Specified VOL IOL RC RC CC VC -VC NOTE A: Arrows indicate actual direction of current flow. Current into a terminal is a positive value. Figure 1. VT+, VIT-, VOH, VOL VCC VI ICC IIH Open -IIL Response Control Open NOTE A: Arrows indicate actual direction of current flow. Current into a terminal is a positive value. Figure 2. IIH, IIL, ICC VCC -IOS Response Control Open NOTE A: Arrows indicate actual direction of current flow. Current into a terminal is a positive value. Figure 3. IOS 4 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 -IOH SN75C189, SN75C189A QUADRUPLE LOW-POWER LINE RECEIVERS SLLS041G - OCTOBER 1988 - REVISED JANUARY 2000 PARAMETER MEASUREMENT INFORMATION VCC Pulse Generator (see Note B) Output RL = 5 k Response Control Open CL = 50 pF (see Note A) TEST CIRCUIT 3V 1.5 V Input 1.5 V 0V tPLH tPHL 90% Output 90% 1.5 V 10% 1.5 V 10% tTHL VOH VOL tTLH VOLTAGE WAVEFORMS NOTES: A. CL includes probe and jig capacitances. B. The pulse generator has the following characteristics: ZO = 50 , tw = 25 s. Figure 4. Test Circuit and Voltage Waveforms POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 5 SN75C189, SN75C189A QUADRUPLE LOW-POWER LINE RECEIVERS SLLS041G - OCTOBER 1988 - REVISED JANUARY 2000 TYPICAL CHARACTERISTICS SN75C189 INPUT THRESHOLD VOLTAGE (POSITIVE GOING) vs FREE-AIR TEMPERATURE SN75C189A INPUT THRESHOLD VOLTAGE (POSITIVE GOING) vs FREE-AIR TEMPERATURE 2.4 1.5 VCC = 5.5 V V IT+ - Input Threshold Voltage - V V IT+ - Input Threshold Voltage - V VCC = 5.5 V 1.4 1.3 1.2 2.2 2 1.8 1.6 1.4 1.2 1.1 0 20 40 60 80 0 100 20 Figure 5 80 100 SN75C189A INPUT THRESHOLD VOLTAGE (NEGATIVE GOING) vs FREE-AIR TEMPERATURE 1.2 1.15 VCC = 5.5 V VCC = 5.5 V V IT- - Input Threshold Voltage - V V IT- - Input Threshold Voltage - V 60 Figure 6 SN75C189 INPUT THRESHOLD VOLTAGE (NEGATIVE GOING) vs FREE-AIR TEMPERATURE 1.1 1 0.9 1.1 1.05 1 0.95 0.9 0.85 0.8 0 20 40 60 80 100 0 TA - Free-Air Temperature - C 20 40 Figure 8 POST OFFICE BOX 655303 60 80 TA - Free-Air Temperature - C Figure 7 6 40 TA - Free-Air Temperature - C TA - Free-Air Temperature - C * DALLAS, TEXAS 75265 100 SN75C189, SN75C189A QUADRUPLE LOW-POWER LINE RECEIVERS SLLS041G - OCTOBER 1988 - REVISED JANUARY 2000 TYPICAL CHARACTERISTICS SN75C189A INPUT HYSTERESIS vs FREE-AIR TEMPERATURE SN75C189 INPUT HYSTERESIS vs FREE-AIR TEMPERATURE 1.2 0.40 0.38 1.1 0.36 Vhys - Input Hysteresis - V Vhys - Input Hysteresis - V VCC = 5 V VCC = 5 V 0.34 0.32 0.30 0.28 0.26 1 0.9 0.8 0.7 0.6 0.24 0.5 0.22 0.20 0.4 0 20 40 60 80 100 120 0 20 TA - Free-Air Temperature - C VOL - Low-Level Output Voltage - V VOH - High-Level Output Voltage - V 3.8 VCC = 4.5 V IOH = -3.2 mA VI = 0.75 V 3.4 3.2 3 2.8 2.6 2.4 2.2 40 100 LOW-LEVEL OUTPUT VOLTAGE vs FREE-AIR TEMPERATURE 3.8 20 80 Figure 10 HIGH-LEVEL OUTPUT VOLTAGE vs FREE-AIR TEMPERATURE 0 60 TA - Free-Air Temperature - C Figure 9 3.6 40 60 80 100 VCC = 4.5 V IOH = -3.2 mA VI = 3 V 3.6 3.4 3.2 3 2.8 2.6 2.4 2.2 0 TA - Free-Air Temperature - C 20 40 60 80 100 TA - Free-Air Temperature - C Figure 11 Figure 12 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 7 SN75C189, SN75C189A QUADRUPLE LOW-POWER LINE RECEIVERS SLLS041G - OCTOBER 1988 - REVISED JANUARY 2000 TYPICAL CHARACTERISTICS SN75C189 HIGH-LEVEL INPUT CURRENT vs FREE-AIR TEMPERATURE SN75C189A HIGH-LEVEL INPUT CURRENT vs FREE-AIR TEMPERATURE 0.65 VCC = 4.5 V VI = 3 V I IH - High-Level Input Current - mA I IH - High-Level Input Current - mA 0.7 0.65 0.6 0.55 0.5 0.45 VCC = 4.5 V VI = 3 V 0.6 0.55 0.5 0.45 0.4 0.35 0.4 0 20 40 60 80 100 0 20 TA - Free-Air Temperature - C 80 100 Figure 14 SN75C189 LOW-LEVEL INPUT CURRENT vs FREE-AIR TEMPERATURE SN75C189A LOW-LEVEL INPUT CURRENT vs FREE-AIR TEMPERATURE -0.2 -0.2 VCC = 4.5 V VI = 3 V I IL - Low-Level Input Current - mA VCC = 4.5 V VI = 3 V I IL - Low-Level Input Current - mA 60 TA - Free-Air Temperature - C Figure 13 -0.3 -0.4 -0.5 -0.6 -0.7 -0.3 -0.4 -0.5 -0.6 -0.7 -0.8 -0.8 0 20 40 60 80 100 0 20 40 Figure 15 Figure 16 POST OFFICE BOX 655303 60 80 TA - Free-Air Temperature - C TA - Free-Air Temperature - C 8 40 * DALLAS, TEXAS 75265 100 SN75C189, SN75C189A QUADRUPLE LOW-POWER LINE RECEIVERS SLLS041G - OCTOBER 1988 - REVISED JANUARY 2000 HIGH-LEVEL SHORT-CIRCUIT OUTPUT CURRENT vs FREE-AIR TEMPERATURE 0 VCC = 5.5 V VO = 0 -2 -4 -6 -8 -10 -12 -14 -16 0 20 40 60 80 100 I OS(L) - Low-Level Short-Circuit Output Current - mA IOS(H) - High-Level Short-Circuit Output Current - mA TYPICAL CHARACTERISTICS LOW-LEVEL SHORT-CIRCUIT OUTPUT CURRENT vs FREE-AIR TEMPERATURE 30 VCC = 5.5 V VI = 0 25 20 15 10 5 0 0 20 TA - Free-Air Temperature - C SUPPLY CURRENT vs FREE-AIR TEMPERATURE 800 VCC = 5.5 V VI = 5 V I CC - Supply Current - A 600 500 400 300 200 100 0 0 20 40 60 80 100 Figure 18 60 80 100 TA - Free-Air Temperature - C t PLH - Propagation Delay Time, Low-to-High Level Output - s Figure 17 700 40 TA - Free-Air Temperature - C PROPAGATION DELAY TIME, LOW- TO HIGH-LEVEL OUTPUT vs FREE-AIR TEMPERATURE 5 VCC = 4.5 V CL = 50 pF 4.5 4 3.5 3 2.5 2 0 Figure 19 20 40 60 80 100 TA - Free-Air Temperature - C Figure 20 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 9 SN75C189, SN75C189A QUADRUPLE LOW-POWER LINE RECEIVERS SLLS041G - OCTOBER 1988 - REVISED JANUARY 2000 PROPAGATION DELAY TIME, HIGH- TO LOW-LEVEL OUTPUT vs FREE-AIR TEMPERATURE t TLH - Transition Time, Low-to-High Level Output - s t PHL - Propagation Delay Time, High-to-Low Level Output - s TYPICAL CHARACTERISTICS 4 VCC = 4.5 V CL = 50 pF 3.9 3.8 3.7 3.6 3.5 3.4 3.3 3.2 0 20 40 60 80 100 TA - Free-Air Temperature - C TRANSITION TIME, LOW- TO HIGH-LEVEL OUTPUT vs FREE-AIR TEMPERATURE 400 VCC = 4.5 V CL = 50 pF 350 300 250 200 150 100 0 20 t THL - Transition Time, High-to-Low Level Output - s Figure 22 TRANSITION TIME, HIGH- TO LOW-LEVEL OUTPUT vs FREE-AIR TEMPERATURE 200 VCC = 4.5 V CL = 50 pF 180 160 140 120 100 80 60 40 0 20 40 60 80 TA - Free-Air Temperature - C Figure 23 POST OFFICE BOX 655303 60 80 TA - Free-Air Temperature - C Figure 21 10 40 * DALLAS, TEXAS 75265 100 100 PACKAGE OPTION ADDENDUM www.ti.com 4-Jun-2007 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty SN75C189AD ACTIVE SOIC D 14 SN75C189ADBLE OBSOLETE SSOP DB 14 SN75C189ADBR ACTIVE SSOP DB 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN75C189ADBRE4 ACTIVE SSOP DB 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN75C189ADBRG4 ACTIVE SSOP DB 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN75C189ADE4 ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN75C189ADG4 ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN75C189ADR ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN75C189ADRE4 ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN75C189ADRG4 ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN75C189AN ACTIVE PDIP N 14 25 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type SN75C189ANE4 ACTIVE PDIP N 14 25 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type SN75C189ANSR ACTIVE SO NS 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN75C189ANSRE4 ACTIVE SO NS 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN75C189ANSRG4 ACTIVE SO NS 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN75C189D ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN75C189DE4 ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN75C189DG4 ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN75C189DR ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN75C189DRE4 ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN75C189DRG4 ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN75C189N ACTIVE PDIP N 14 25 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type SN75C189NE4 ACTIVE PDIP N 14 25 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type SN75C189NSR ACTIVE SO NS 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN75C189NSRE4 ACTIVE SO NS 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 50 Green (RoHS & no Sb/Br) TBD Addendum-Page 1 Lead/Ball Finish CU NIPDAU Call TI MSL Peak Temp (3) Level-1-260C-UNLIM Call TI PACKAGE OPTION ADDENDUM www.ti.com 4-Jun-2007 Orderable Device Status (1) Package Type Package Drawing SN75C189NSRG4 ACTIVE SO NS Pins Package Eco Plan (2) Qty 14 2000 Green (RoHS & no Sb/Br) Lead/Ball Finish CU NIPDAU MSL Peak Temp (3) Level-1-260C-UNLIM (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant SN75C189ADBR SSOP DB 14 2000 330.0 16.4 8.2 6.6 2.5 12.0 16.0 Q1 SN75C189ADR SOIC D 14 2500 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1 SN75C189ADR SOIC D 14 2500 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1 SN75C189ANSR SO NS 14 2000 330.0 16.4 8.2 10.5 2.5 12.0 16.0 Q1 SN75C189DR SOIC D 14 2500 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1 SN75C189NSR SO NS 14 2000 330.0 16.4 8.2 10.5 2.5 12.0 16.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) SN75C189ADBR SSOP DB 14 2000 367.0 367.0 38.0 SN75C189ADR SOIC D 14 2500 367.0 367.0 38.0 SN75C189ADR SOIC D 14 2500 333.2 345.9 28.6 SN75C189ANSR SO NS 14 2000 367.0 367.0 38.0 SN75C189DR SOIC D 14 2500 367.0 367.0 38.0 SN75C189NSR SO NS 14 2000 367.0 367.0 38.0 Pack Materials-Page 2 MECHANICAL DATA MSSO002E - JANUARY 1995 - REVISED DECEMBER 2001 DB (R-PDSO-G**) PLASTIC SMALL-OUTLINE 28 PINS SHOWN 0,38 0,22 0,65 28 0,15 M 15 0,25 0,09 8,20 7,40 5,60 5,00 Gage Plane 1 14 0,25 A 0-8 0,95 0,55 Seating Plane 2,00 MAX 0,10 0,05 MIN PINS ** 14 16 20 24 28 30 38 A MAX 6,50 6,50 7,50 8,50 10,50 10,50 12,90 A MIN 5,90 5,90 6,90 7,90 9,90 9,90 12,30 DIM 4040065 /E 12/01 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion not to exceed 0,15. Falls within JEDEC MO-150 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such components to meet such requirements. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2012, Texas Instruments Incorporated