HY57V28820A Revision History Revision 1.1 (Dec. 2000) * * Eleminated -10 Bining product. Changed DC Characteristics-ll. - tCK to 15ns from min in Test condition - -K IDD1 to 120mA from 110mA - -K IDD4 CL2 to 120mA from 100mA. - -K IDD5 to 240mA from 220mA. - -S IDD4 CL2 to 90mA from 100mA * Added Burst-Read-Single-Write commend in Commend Truth Table 1.2 : Hynix Change 1.3 : Burst read single write mode correction Rev. 1.3/Aug. 01 1 HY57V28820A 4Banks x 4M x 8bits Synchronous DRAM DESCRIPTION The Hynix HY57V28820A is a 134,217,728bit CMOS Synchronous DRAM, ideally suited for the main memory applications which require large memory density and high bandwidth. HY57V28820A is organized as 4banks of 4,194,304x8. HY57V28820A is offering fully synchronous operation referenced to a positive edge of the clock. All inputs and outputs are synchronized with the rising edge of the clock input. The data paths are internally pipelined to achieve very high bandwidth. All input and output voltage levels are compatible with LVTTL. Programmable options include the length of pipeline (Read latency of 2 or 3), the number of consecutive read or write cycles initiated by a single control command (Burst length of 1,2,4,8 or full page), and the burst count sequence(sequential or interleave). A burst of read or write cycles in progress can be terminated by a burst terminate command or can be interrupted and replaced by a new burst read or write command on any cycle. (This pipelined design is not restricted by a 2N rule.) FEATURES * Single 3.30.3V power supply * Auto refresh and self refresh * All device pins are compatible with LVTTL interface * 4096 refresh cycles / 64ms * JEDEC standard 400mil 54pin TSOP-II with 0.8mm of pin pitch * Programmable Burst Length and Burst Type * All inputs and outputs referenced to positive edge of system clock - 1, 2, 4, 8 or Full Page for Sequential Burst * Data mask function by DQM * Internal four banks operation - 1, 2, 4 or 8 for Interleave Burst * Programmable CAS Latency ; 2, 3 Clocks ORDERING INFORMATION Part No. Clock Frequency HY57V28820AT-6 166MHz HY57V28820AT-K 133MHz HY57V28820AT-H 133MHz HY57V28820AT-8 125MHz HY57V28820AT-P 100MHz HY57V28820AT-S 100MHz HY57V28820ALT-6 166MHz HY57V28820ALT-K 133MHz HY57V28820ALT-H 133MHz HY57V28820ALT-8 125MHz HY57V28820ALT-P 100MHz HY57V28820ALT-S 100MHz Power Organization Interface Package 4Banks x 4Mbits x8 LVTTL 400mil 54pin TSOP II Normal Low power This document is a general product description and is subject to change without notice. Hynix does not assume any responsibility for use of circuits described. No patent licenses are implied. Rev. 1.3/Aug. 01 HY57V28820A PIN CONFIGURATION VDD DQ0 VDDQ NC DQ1 VSSQ NC DQ2 VDDQ NC DQ3 VSSQ NC VDD NC /WE /CAS /RAS /CS BA0 BA1 A10/AP A0 A1 A2 A3 VDD 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 54pin TSOP II 400mil x 875mil 0.8mm pin pitch 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 VSS DQ7 VSSQ NC DQ6 VDDQ NC DQ5 VSSQ NC DQ4 VDDQ NC VSS NC DQM CLK CKE NC A11 A9 A8 A7 A6 A5 A4 VSS PIN DESCRIPTION PIN PIN NAME DESCRIPTION CLK Clock The system clock input. All other inputs are registered to the SDRAM on the rising edge of CLK CKE Clock Enable Controls internal clock signal and when deactivated, the SDRAM will be one of the states among power down, suspend or self refresh CS Chip Select Enables or disables all inputs except CLK, CKE and DQM BA0, BA1 Bank Address Selects bank to be activated during RAS activity Selects bank to be read/written during CAS activity A0 ~ A11 Address Row Address : RA0 ~ RA11, Column Address : CA0 ~ CA9 Auto-precharge flag : A10 RAS, CAS, WE Row Address Strobe, Column Address Strobe, Write Enable RAS, CAS and WE define the operation Refer function truth table for details DQM Data Input/Output Mask Controls output buffers in read mode and masks input data in write mode DQ0 ~ DQ7 Data Input/Output Multiplexed data input / output pin VDD/VSS Power Supply/Ground Power supply for internal circuits and input buffers VDDQ/VSSQ Data Output Power/Ground Power supply for output buffers NC No Connection No connection Rev. 1.3/Aug. 01 HY57V28820A FUNCTIONAL BLOCK DIAGRAM 4Mbit x 4banks x 8 I/O Synchronous DRAM Self refresh logic & timer Internal Row counter 4Mx8 Bank3 CLK Row active Column Pre Decoders DQM Y decoders Bank Select A0 A1 Column Add Counter Address Registers Address buffers A11 BA0 BA1 Rev. 1.3/Aug. 01 Burst Counter Mode Registers CAS Latency Data Out Control Pipe Line Control DQ0 I/O Buffer & Logic Column Active Memory Cell Array Sense AMP & I/O Gate WE X decoders refresh 4Mx8 Bank 0 X decoders CAS 4Mx8 Bank 1 X decoders RAS State Machine CS 4Mx8 Bank 2 X decoders CKE Row Pre Decoders DQ1 DQ6 DQ7 HY57V28820A ABSOLUTE MAXIMUM RATINGS Parameter Symbol Rating Unit Ambient Temperature TA 0 ~ 70 C Storage Temperature TSTG -55 ~ 125 C Voltage on Any Pin relative to VSS VIN, VOUT -1.0 ~ 4.6 V Voltage on VDD relative to VSS VDD, VDDQ -1.0 ~ 4.6 V Short Circuit Output Current IOS 50 mA Power Dissipation PD 1 W Soldering Temperature Time TSOLDER 260 10 C Sec Note : Operation at above absolute maximum rating can adversely affect device reliability. DC OPERATING CONDITION (TA=0 to 70C) Parameter Symbol Min Typ Max Unit Note Power Supply Voltage VDD, VDDQ 3.0 3.3 3.6 V 1 Input High voltage VIH 2.0 3.0 VDDQ + 0.3 V 1,2 Input Low voltage VIL -0.3 0 0.8 V 1,3 Note Note : 1.All voltages are referenced to VSS = 0V 2.VIH(max) is acceptable 5.6V AC pulse width with <=3ns of duration. 3.VIL(min) is acceptable -2.0V AC pulse width with <=3ns of duration. AC OPERATING TEST CONDITION (TA=0 to 70C, VDD=3.30.3V, VSS=0V) Parameter Symbol Value Unit AC Input High / Low Level Voltage VIH / VIL 2.4/0.4 V Vtrip 1.4 V Input Rise / Fall Time tR / tF 1 ns Output Timing Measurement Reference Level Voltage Voutref 1.4 V CL 50 pF Input Timing Measurement Reference Level Voltage Output Load Capacitance for Access Time Measurement 1 Note : 1.Output load to measure access times is equivalent to two TTL gates and one capacitor (50pF). For details, refer to AC/DC output load circuit Rev. 1.3/Aug. 01 HY57V28820A CAPACITANCE (TA=25C, f=1MHz) -6/K/H Parameter Pin Input Capacitance Data Input / Output Capacitance -8/P/S Symbol Unit Min. Max. Min. Max. CLK CI1 2.5 3.5 2.5 4 pF A0 ~ A11, BA0, BA1, CKE, CS, RAS, CAS, WE, DQM CI2 2.5 3.8 2.5 5 pF DQ0 ~ DQ7 CI/O 4 6.5 4 6.5 pF OUTPUT LOAD CIRCUIT Vtt=1.4V RT=250 Output Output 50pF 50pF DC Output Load Circuit AC O utput Load Circuit DC CHARACTERISTICS I (TA=0 to 70C, VDD=3.30.3V) Parameter Symbol Min. Max Unit Note Input Leakage Current ILI -1 1 uA 1 Output Leakage Current ILO -1 1 uA 2 Output High Voltage VOH 2.4 - V IOH = -4mA Output Low Voltage VOL - 0.4 V IOL =+4mA Note : 1.VIN = 0 to 3.6V, All other pins are not under test = 0V 2.DOUT is disabled, VOUT=0 to 3.6V Rev. 1.3/Aug. 01 HY57V28820A DC CHARACTERISTICS II (TA=0 to 70C, VDD=3.30.3V, VSS=0V) Speed Parameter Symbol Test Condition -6 -K -H -8 -P -S 120 120 110 100 100 100 IDD1 Burst length=1, One bank active tRC tRC(min), IOL=0mA IDD2P CKE VIL(max), tCK = 15ns 2 IDD2PS CKE VIL(max), tCK = 2 IDD2N CKE VIH(min), CS VIH(min), tCK = 15ns Input signals are changed one time during 2clks. All other pins VDD-0.2V or 0.2V 20 IDD2NS CKE VIH(min), tCK = Input signals are stable. 10 IDD3P CKE VIL(max), tCK = 15ns 7 IDD3PS CKE VIL(max), tCK = 7 IDD3N CKE VIH(min), CS VIH(min), tCK = 15ns Input signals are changed one time during 2clks. All other pins VDD-0.2V or 0.2V 40 IDD3NS CKE VIH(min), tCK = Input signals are stable. 40 Burst Mode Operating Current IDD4 tCK tCK(min), IOL=0mA All banks active Auto Refresh Current IDD5 tRRC tRRC(min), All banks active Self Refresh Current IDD6 CKE 0.2V Operating Current Precharge Standby Current in Power Down Mode Precharge Standby Current in Non Power Down Mode Active Standby Current in Power Down Mode Active Standby Current in Non Power Down Mode Note mA 1 mA mA mA mA CL=3 140 120 120 110 100 100 CL=2 100 120 100 100 100 90 240 240 220 200 200 200 mA 1 mA 2 2 mA 3 800 uA 4 Note : 1.IDD1 and IDD4 depend on output loading and cycle rates. Specified values are measured with the output open. 2.Min. of tRRC (Refresh RAS cycle time) is applied to HY57V28820AT-6/K/H/8/P/S which are listed on AC characteristic II. 3.HY57V28820AT-6/K/H/8/P/S 4.HY57V28820ALT-6/K/H/8/P/S Rev. 1.3/Aug. 01 Unit HY57V28820A AC CHARACTERISTICS I (AC operating conditions unless otherwise noted) -6 Parameter CAS Latency = 3 tCK3 Max 6 Min Max 7.5 1000 -8 -P -S Min Max Min 7.5 1000 8 1000 10 Min Max 10 1000 10 Min 10 1000 ns 1000 Clock High Pulse Width tCHW 2.5 - 2.5 - 2.5 - 3 - 3 - 3 - ns 1 Clock Low Pulse Width tCLW 2.5 - 2.5 - 2.5 - 3 - 3 - 3 - ns 1 CAS Latency = 3 tAC3 - 5.4 - 5.4 - 5.4 - 6 - 6 - 6 ns CAS Latency = 2 tAC2 - 6 - 5.4 - 6 - 6 - 6 - 6 ns Data-Out Hold Time tOH 2.7 - 2.7 - 2.7 - 3 - 3 - 3 - ns Data-Input Setup Time tDS 1.5 - 1.5 - 1.5 - 2 - 2 - 2 - ns 1 Data-Input Hold Time tDH 0.8 - 0.8 - 0.8 - 1 - 1 - 1 - ns 1 Address Setup Time tAS 1.5 - 1.5 - 1.5 - 2 - 2 - 2 - ns 1 Address Hold Time tAH 0.8 - 0.8 - 0.8 - 1 - 1 - 1 - ns 1 CKE Setup Time tCKS 1.5 - 1.5 - 1.5 - 2 - 2 - 2 - ns 1 CKE Hold Time tCKH 0.8 - 0.8 - 0.8 - 1 - 1 - 1 - ns 1 Command Setup Time tCS 1.5 - 1.5 - 1.5 - 2 - 2 - 2 - ns 1 Command Hold Time tCH 0.8 - 0.8 - 0.8 - 1 - 1 - 1 - ns 1 CLK to Data Output in Low-Z Time tOLZ 1 - 1 - 1 - 1 - 1 - 1 - ns 12 ns 2 CAS Latency = 3 tOHZ3 2.7 5.4 2.7 5.4 2.7 5.4 3 6 3 6 3 6 ns CAS Latency = 2 tOHZ2 2.7 5.4 2.7 5.4 3 6 3 6 3 6 3 6 ns Note : 1.Assume tR / tF (input rise and fall time ) is 1ns If tR & tF > 1ns, then [(tR+tF)/2-1]ns should be added to the parameter 2.Access times to be measured with input signals of 1v/ns edge rate, from 0.8v to 2.0v If tR > 1ns, then (tR/2-0.5)ns should be added to the parameter Rev. 1.3/Aug. 01 10 Note Max 10 CLK to Data Output in High-Z Time 7.5 Max tCK2 Access Time From Clock CAS Latency = 2 -H Unit Min System Clock Cycle Time -K Symbol HY57V28820A AC CHARACTERISTICS II -6 Parameter -K -H -8 -P -S -10 Symbol Unit Min Max Min Max Min Max Min Max Min Max Min Max Min Max Operation tRC 60 - 60 - 65 - 68 - 70 - 70 - 80 - ns Auto Refresh tRRC 60 - 60 - 65 - 68 - 70 - 70 - 96 - ns RAS to CAS Delay tRCD 18 - 15 - 20 - 20 - 20 - 20 - 30 - ns RAS Active Time tRAS 42 100K 45 100K 45 100K 48 100K 50 100K 50 100K 50 100K ns RAS Precharge Time tRP 18 - 15 - 20 - 20 - 20 - 20 - 30 - ns RAS to RAS Bank Active Delay tRRD 12 - 15 - 15 - 16 - 20 - 20 - 20 - ns CAS to CAS Delay tCCD 1 - 1 - 1 - 1 - 1 - 1 - 1 - CLK Write Command to Data-In Delay tWTL 0 - 0 - 0 - 0 - 0 - 0 - 0 - CLK Data-In to Precharge Command tDPL 2 - 2 - 2 - 1 - 1 - 1 - 1 - CLK Data-In to Active Command tDAL 5 - 4 - 5 - 4 - 3 - 3 - 4 - CLK DQM to Data-Out Hi-Z tDQZ 2 - 2 - 2 - 2 - 2 - 2 - 2 - CLK DQM to Data-In Mask tDQM 0 - 0 - 0 - 0 - 0 - 0 - 0 - CLK MRS to New Command tMRD 2 - 2 - 2 - 2 - 2 - 2 - 2 - CLK CAS Latency = 3 tPROZ3 3 - 3 - 3 - 3 - 3 - 3 - 3 - CLK CAS Latency = 2 tPROZ2 2 - 2 - 2 - 2 - 2 - 2 - 2 - CLK Power Down Exit Time tPDE 1 - 1 - 1 - 1 - 1 - 1 - 1 - CLK Self Refresh Exit Time tSRE 1 - 1 - 1 - 1 - 1 - 1 - 1 - CLK Refresh Time tREF - 64 - 64 - 64 - 64 - 64 - 64 - 64 ms Note RAS Cycle Time Precharge to Data Output Hi-Z Note : 1. A new command can be given tRRC after self refresh exit. Rev. 1.3/Aug. 01 1 HY57V28820A IBIS SPECIFICATION IOH Characteristics (Pull-up) (V) 100MHz Min 100MHz Max 66MHz Min I (mA) I (mA) I (mA) 3.45 -2.4 3.3 -27.3 0 0.5 1 1.5 2 2.5 3 3.5 3 3.5 0 -100 -200 3.0 0.0 -74.1 -0.7 2.6 -21.1 -129.2 -7.5 2.4 -34.1 -153.3 -13.3 2.0 -58.7 -197.0 -27.5 1.8 -67.3 -226.2 -35.5 1.65 -73.0 -248.0 -41.1 1.5 -77.9 -269.7 -47.9 1.4 -80.8 -284.3 -52.4 1.0 -88.6 -344.5 -72.5 0.0 -93.0 -502.4 -93.0 I (mA) Voltage 66MHz and 100MHz Pull-up -300 -400 -500 -600 Voltage (V) Ioh Min (100MHz) Ioh Min (66MHz) Ioh Min (66 and 100MHz) IOL Characteristics (Pull-down) 66MHz and 100MHz Pull-down 100MHz Min 100MHz Max 66MHz Min 250 (V) I (mA) I (mA) I (mA) 200 0.0 0.0 0.0 0.0 0.4 27.5 70.2 17.7 0.65 41.8 107.5 26.9 0.85 51.6 133.8 33.3 1.0 58.0 151.2 37.6 1.4 70.7 187.7 46.6 1.5 72.9 194.4 48.0 1.65 75.4 202.5 49.5 1.8 77.0 208.6 50.7 1.95 77.6 212.0 51.5 3.0 80.3 219.6 54.2 3.45 81.4 222.6 54.9 Rev. 1.3/Aug. 01 I (mA) Voltage 150 100 50 0 0 0.5 1 1.5 2 Voltage (V) 2.5 I (mA) 100 min I (mA) 66 min I (mA) 100 max HY57V28820A Minimum VDD clamp current VDD Clamp @ CLK, CKE, CS, DQM & DQ I(mA) 0.0 0.0 0.2 0.0 0.4 0.0 0.6 0.0 0.7 0.0 0.8 0.0 0.9 0.0 1.0 0.23 1.2 1.34 1.4 3.02 1.6 5.06 1.8 7.35 2.0 9.83 2.2 12.48 2.4 15.30 2.6 18.31 (Referenced to VDD) 20 15 mA VDD (V) 10 5 0 0 1 Minimum VSS clamp current -57.23 -2.4 -45.77 -2.2 -38.26 -2.0 -31.22 -1.8 -24.58 -1.6 -18.37 -1.4 -12.56 -1.2 -7.57 -1.0 -3.37 -0.9 -1.75 -0.8 -0.58 -0.7 -0.05 -0.6 0.0 -0.4 0.0 -0.2 0.0 0.0 0.0 Rev. 1.3/Aug. 01 -3 -2.5 -2 -1.5 0 -10 -20 mA I (mA) -2.6 3 I (mA) VSS Clamp @ CLK, CKE, CS, DQM & DQ VSS (V) 2 Voltage -30 -40 -50 -60 Voltage I (mA) -1 -0.5 0 HY57V28820A DEVICE OPERATING OPTION TABLE HY57V28820A(L)T-6 CAS Latency tRCD tRAS tRC tRP tAC tOH 3CLKs 3CLKs 2CLKs 3CLKs 3CLKs 3CLKs 7CLKs 6CLKs 6CLKs 10CLKs 9CLKs 9CLKs 3CLKs 3CLKs 3CLKs 5.4ns 5.4ns 5.4ns 2.7ns 2.7ns 2.7ns CAS Latency tRCD tRAS tRC tRP tAC tOH 125MHz(8ns) 2CLKs 3CLKs 2CLKs 3CLKs 6CLKs 6CLKs 8CLKs 9CLKs 2CLKs 3CLKs 5.4ns 6ns 2.7ns 3ns 100MHz(10ns) 2CLKs 2CLKs 5CLKs 7CLKs 2CLKs 6ns 3ns 166MHz(6ns) 143MHz(7ns) 133MHz(7.5ns) HY57V28820A(L)T-K 133MHz(7.5ns) HY57V28820A(L)T-H 133MHz(7.5ns) 125MHz(8ns) 100MHz(10ns) CAS Latency tRCD tRAS tRC tRP tAC tOH 3CLKs 3CLKs 2CLKs 3CLKs 3CLKs 2CLKs 6CLKs 6CLKs 5CLKs 9CLKs 9CLKs 7CLKs 3CLKs 3CLKs 2CLKs 5.4ns 6ns 6ns 2.7ns 3ns 3ns HY57V28820A(L)T-8 125MHz(8ns) 100MHz(10ns) 83MHz(12ns) CAS Latency tRCD tRAS tRC tRP tAC tOH 3CLKs 2CLKs 2CLKs 3CLKs 2CLKs 2CLKs 6CLKs 5CLKs 4CLKs 9CLKs 7CLKs 6CLKs 3CLKs 2CLKs 2CLKs 6ns 6ns 6ns 3ns 3ns 3ns CAS Latency tRCD tRAS tRC tRP tAC tOH 2CLKs 2CLKs 2CLKs 2CLKs 2CLKs 2CLKs 5CLKs 5CLKs 4CLKs 7CLKs 7CLKs 6CLKs 2CLKs 2CLKs 2CLKs 6ns 6ns 6ns 3ns 3ns 3ns CAS Latency tRCD tRAS tRC tRP tAC tOH 3CLKs 2CLKs 2CLKs 2CLKs 2CLKs 2CLKs 5CLKs 5CLKs 4CLKs 7CLKs 7CLKs 6CLKs 2CLKs 2CLKs 2CLKs 6ns 6ns 6ns 3ns 3ns 3ns HY57V28820A(L)T-P 100MHz(10ns) 83MHz(12ns) 66MHz(15ns) HY57V28820A(L)T-S 100MHz(10ns) 83MHz(12ns) 66MHz(15ns) Rev. 1.3/Aug. 01 HY57V28820A COMMAND TRUTH TABLE Command A10/ AP CKEn-1 CKEn CS RAS CAS WE DQM Mode Register Set H X L L L L X OP code H X X X No Operation H X X X L H H H Bank Active H X L L H H X H X L H L H X ADDR RA Read 1 L V H Write L H X L H L L X CA Write with Autoprecharge H X L L H L X Precharge selected Bank Burst Stop H DQM H Auto Refresh H H L L L Burst-Read-SingleWRITE H X L L Entry H L L X H Exit L H H L H H L X L V X V X H X X L L X A9 Pin High (Other Pins OP code) L L H X X X X X X L H H H H X X X L H H H H X X X L H H H H X X X L V V V L Precharge power down H X X X Self Refresh Entry V H Precharge All Banks X X Exit Entry Exit L H L H X L H X X X X Note : 1. Exiting Self Refresh occurs by asynchronously bringing CKE from low to high 2. X = Dont care, H = Logic High, L= Logic Low, BA=Bank Address, RA = Row Address, CA = Column Address, Opcode=Operand Code, NOP=No Operation 3. The burst read sigle write mode is entered by programming the write burst mode bit (A9) in the mode register to a logic 1. Rev. 1.3/Aug. 01 Note V CA Read with Autoprecharge Clock Suspend BA 3 HY57V28820A PACKAGE INFORMATION 400mil 54pin Thin Small Outline Package Unit : mm(inch) Rev. 1.3/Aug. 01