Engineering Bulletin Tentative Conductive Polymer Aluminum Solid Capacitors No.740A / Nov.2003 Feature! @Super low ESR, impedance and high heat resistance have been obtained by using conductive polymer as electrolyte. @Suitable for DC-DC converters, voltage regulators and decoupling applications. @Endurance with ripple current : 125C 1000 hours @Rated voltage range : 2.5 to 20Vdc, Capacitance range : 22 to 1000MF @Case size range : F6.3B6.0mm to F10B8.0mm Pb Free Type ?SPECIFICATIONS Items Characteristics Category Temperature Range Rated Voltage Range Capacitance Tolerance Surge Voltage Leakage Current Dissipation Factor (tane) Low Temperature Characteristics (Max. Impedance Ratio) Endurance Bias Humidity Surge Voltage Failure Rate -55 to +125C 2.5 to 20Vdc P20% (M) Rated voltageB1.15V Shall not exceed value shown in STANDARD RATINGS. (at 20C, 120Hz) (at 105C) (at 20C after 2 minutes) 0.12 max. (at 20C, 120Hz) Z(-25C)/Z(+20C)[1.15 Z(-55C)/Z(+20C)[1.25 (at 100kHz) The following specifications shall be satisfied when the capacitors are restored to 20C after the rated voltage is applied for 1000 hours at 125C. Appearance No significant damage Capacitance change [P20% of the initial value DF (tanE) [200% of the initial specified value ESR [200% of the initial specified value Leakage current [The initial specified value The following specifications shall be satisfied when the capacitors are restored to 20C after subjecting them to the DC rated voltage at 60C, 90 to 95% RH for 1000 hours. Appearance No significant damage Capacitance change [P20% of the initial value DF (tanE) [150% of the initial specified value ESR [150% of the initial specified value Leakage current [The initial specified value The capacitors shall be subjected to 1000 cycles each consisting of charge with the surge voltage specified at 105C for 30 seconds through a protective resistor(R=1kO) and discharge for 5 minutes 30 seconds. Appearance No significant damage Capacitance change [P20% of the initial value DF (tanE) [150% of the initial specified value ESR [150% of the initial specified value Leakage current [The initial specified value 1% per 1000 hours maximum (Confidence level 60%) *Note : If any doubt arises, measure the leakage current after following voltage treatment. Voltage treatment : DC rated voltage are applied to the capacitors for 120 minutes at 125C. ?DIMENSIONS [mm] ?MARKING EX) PXH20VC22MF60 P CP0.2 BP0.2 FDP0.5 W 0.3max. LP0.3 Case code F60 H70 J80 fD 6.3 8 10 L 5.7 6.7 7.7 A B C 6.6 6.6 7.2 8.3 8.3 9.0 10.3 10.3 11.0 W 0.5 to 0.8 0.7 to 1.1 0.7 to 1.1 P 1.9 3.1 4.5 H39F 22 20V AP0.2 ?PART NUMBERING SYSTEM PXH 20 VC 22 M F60 Case code Cap tolerance (P20%) Nominal cap code Terminal type Rated voltage in volts Series name Capacitance 39MF 100MF 220MF Code 39 100 220 Specifications in this bulletin are subject to change without notice. Please ask us for technical specifications before purchase and use. NIPPON CHEMI-CON CORPORATION 1190 1 Tentative Engineering Bulletin Conductive Polymer Aluminum Solid Capacitors No.740A / Nov.2003 ?STANDARD RATINGS Case code Rated voltage (Vdc) Nominal Capacitance (mF) Leakage current (mAmax) ESR (momax/ 20c,100k to 300kHz) 2.5 4 6.3 6.3 10 16 20 2.5 4 6.3 6.3 10 10 16 20 2.5 4 6.3 10 16 16 20 220 150 82 100 56 39 22 560 220 150 220 120 150 82 47 1000 470 330 330 150 180 82 110 120 103 126 112 125 88 280 176 189 277 240 300 262 188 500 376 416 660 480 576 328 35 35 40 40 45 50 60 30 30 30 30 35 35 40 45 25 25 25 30 35 35 45 F60 H70 J80 Rated ripple current (mArms/100k to 300kHz) -55 to +105c +105 to +125c 2500 2450 2400 2400 2250 2050 1650 3100 3020 3020 3020 2800 2800 2700 2000 3700 3700 3700 3700 3020 3020 2400 770 770 720 720 680 650 590 960 960 960 960 880 880 830 780 1100 1100 1100 1010 930 930 820 ?Recommended Reflow Soldering Conditions @Reflow Profile Method : Air or Infrated Reflow @Conditions Temperature on the top of capacitor and Temperature of capacitor terminal (C) Peak temperature Peak 230 [The times of reflow soldering : once] Peak temperature : 250C max. Max. period of time over 230C(T1) : 40 sec.max. Max. period of time over 200C(T2) : 60 sec.max. Preheat : 150C, 120 sec. max. T1 200 T2 150 Preheat [The times of reflow soldering : twice] Peak temperature : 250C max. Max. period of time over 230C(T1) : 30 sec.max. Max. period of time over 200C(T2) : 50 sec.max. Preheat : 150C, 120 sec. max. 120sec. max. 25 Time (sec.) ?Recommended Solder Land on PC Board c a b Case code a 1.4 E60 1.9 F60 3.1 H70 b 3.0 3.5 4.2 c 1.6 1.6 2.2 Solder land on PC board Specifications in this bulletin are subject to change without notice. NIPPON CHEMI-CON CORPORATION 1190 2