Engineering Bulletin
Conductive Polymer
Aluminum Solid Capacitors
No.740A / Nov.2003
Tentative
NIPPON CHEMI-CON CORPORATION
1190
1
@Super low ESR, impedance and high heat resistance have been obtained by using
conductive polymer as electrolyte.
@Suitable for DC-DC converters, voltage regulators and decoupling applications.
@Endurance with ripple current : 125C 1000 hours
@Rated voltage range : 2.5 to 20Vdc, Capacitance range : 22 to 1000MF
@Case size range : F6.3B6.0mm to F10B8.0mm
?SPECIFICATIONS
(at 20C, 120Hz)
(at 105C)
(at 20C after 2 minutes)
(at 20C, 120Hz)
(at 100kHz)
Category
Temperature Range
Rated Voltage Range
Capacitance Tolerance
Surge Voltage
Leakage Current
Dissipation Factor
(tane)
Low Temperature
Characteristics
(Max. Impedance Ratio)
Endurance
Bias Humidity
Surge Voltage
Failure Rate
Items
-
55 to +125C
2.5 to 20V
dc
P20% (M)
Rated voltageB1.15V
Shall not exceed value shown in STANDARD RATINGS.
0.12 max.
Z(
-
25C)/Z(+20C)[1.15
Z(
-
55C)/Z(+20C)[1.25
The following specifications shall be satisfied when the capacitors are restored to 20C after the rated voltage is applied for 1000 hours
at 125C.
Appearance No significant damage
Capacitance change [P20% of the initial value
DF (tanE)[200% of the initial specified value
ESR [200% of the initial specified value
Leakage current [The initial specified value
The following specifications shall be satisfied when the capacitors are restored to 20C after subjecting them to the DC rated voltage at
60C, 90 to 95% RH for 1000 hours.
Appearance No significant damage
Capacitance change [P20% of the initial value
DF (tanE)[150% of the initial specified value
ESR [150% of the initial specified value
Leakage current [The initial specified value
The capacitors shall be subjected to 1000 cycles each consisting of charge with the surge voltage specified at 105C for 30 seconds
through a protective resistor(R=1kO) and discharge for 5 minutes 30 seconds.
Appearance No significant damage
Capacitance change [P20% of the initial value
DF (tanE)[150% of the initial specified value
ESR [150% of the initial specified value
Leakage current [The initial specified value
1% per 1000 hours maximum (Confidence level 60%)
Characteristics
?PART NUMBERING SYSTEM
?DIMENSIONS [mm]
FDP0.5
LP0.3
0.3max. AP0.2
W
CP0.2
BP0.2
P
Case code
F60
H70
J80
fD
6.3
8
10
L
5.7
6.7
7.7
A
6.6
8.3
10.3
B
6.6
8.3
10.3
C
7.2
9.0
11.0
W
0.5 to 0.8
0.7 to 1.1
0.7 to 1.1
P
1.9
3.1
4.5
PXH 20 VC 22 M F60
Case code
Cap tolerance (P20%)
Nominal cap code
Terminal type
Rated voltage in volts
Series name
Capacitance
39MF
100MF
220MF
Code
39
100
220
?MARKING
H
39F
22
20
V
EX) PXH20VC22MF60
*Note : If any doubt arises, measure the leakage current after following voltage treatment.
Voltage treatment : DC rated voltage are applied to the capacitors for 120 minutes at 125C.
Feature!
Pb Free Type
Specifications in this bulletin are subject to change without notice.
Please ask us for technical specifications before purchase and use.
Engineering Bulletin
Conductive Polymer
Aluminum Solid Capacitors
No.740A / Nov.2003
Tentative
NIPPON CHEMI-CON CORPORATION
1190
2
?STANDARD RATINGS
Case code
F60
H70
J80
Leakage current
(mAmax) ESR
(momax/
20c,100k to 300kHz)
Rated voltage
(Vdc)
Nominal
Capacitance
(mF)
Rated ripple current (mArms/100k to 300kHz)
-55 to +105c+105 to +125c
2.5
4
6.3
6.3
10
16
20
2.5
4
6.3
6.3
10
10
16
20
2.5
4
6.3
10
16
16
20
220
150
82
100
56
39
22
560
220
150
220
120
150
82
47
1000
470
330
330
150
180
82
110
120
103
126
112
125
88
280
176
189
277
240
300
262
188
500
376
416
660
480
576
328
35
35
40
40
45
50
60
30
30
30
30
35
35
40
45
25
25
25
30
35
35
45
2500
2450
2400
2400
2250
2050
1650
3100
3020
3020
3020
2800
2800
2700
2000
3700
3700
3700
3700
3020
3020
2400
770
770
720
720
680
650
590
960
960
960
960
880
880
830
780
1100
1100
1100
1010
930
930
820
?Recommended Reflow Soldering Conditions
200
230
Peak
150
25
Preheat
120sec. max.
Peak
temperature
Time (sec.)
T2
T1
(C)
Temperature on the top of capacitor
and
Temperature of capacitor terminal
@Reflow Profile
Method : Air or Infrated Reflow [The times of reflow soldering : once]
Peak temperature : 250C max.
Max. period of time over 230C(T1) : 40 sec.max.
Max. period of time over 200C(T2) : 60 sec.max.
Preheat : 150C, 120 sec. max.
[The times of reflow soldering : twice]
Peak temperature : 250C max.
Max. period of time over 230C(T1) : 30 sec.max.
Max. period of time over 200C(T2) : 50 sec.max.
Preheat : 150C, 120 sec. max.
@Conditions
Specifications in this bulletin are subject to change without notice.
?Recommended Solder Land on PC Board
c
b
a
Solder land on PC board
Case code
E60
F60
H70
a
1.4
1.9
3.1
b
3.0
3.5
4.2
c
1.6
1.6
2.2
