Order this document by H11AA1/D SEMICONDUCTOR TECHNICAL DATA GlobalOptoisolator [CTR = 20% Min] [CTR = 10% Min] The H11AA1, H11AA2, H11AA3, H11AA4 devices consist of two gallium- arsenide infrared emitting diodes connected in inverse parallel, optically coupled to a monolithic silicon phototransistor detector. [CTR = 50% Min] [CTR = 100% Min] * Built-In Protection for Reverse Polarity * Guaranteed CTR Minimum Values as High as 100% *Motorola Preferred Devices * Guaranteed Minimum/Maximum Symmetry Limits * To order devices that are tested and marked per VDE 0884 requirements, the suffix "V" must be included at end of part number. VDE 0884 is a test option. STYLE 8 PLASTIC Applications * Detecting or Monitoring ac Signals * AC Line/Digital Logic Isolation * Programmable Controllers * Interfacing and coupling systems of different potentials and impedances 6 * AC/DC -- Input Modules 1 STANDARD THRU HOLE CASE 730A-04 MAXIMUM RATINGS (TA = 25C unless otherwise noted) Rating Symbol Value Unit Forward Current -- Continuous (RMS) IF 60 mA LED Power Dissipation @ TA = 25C with Negligible Power in Output Detector Derate above 25C PD 120 mW 1 1.41 mW/C 2 INPUT LED SCHEMATIC OUTPUT TRANSISTOR VCEO 30 Volts Emitter-Base Voltage VEBO 5 Volts Collector-Base Voltage VCBO 70 Volts Collector Current -- Continuous IC 150 mA Detector Power Dissipation @ TA = 25C with Negligible Power in Input LEDs Derate above 25C PD 150 mW 1.76 mW/C VISO 7500 Vac(pk) Total Device Power Dissipation @ TA = 25C Derate above 25C PD 250 2.94 mW mW/C Ambient Operating Temperature Range(2) TA - 55 to +100 C Tstg - 55 to +150 C TL 260 C 5 4 3 Collector-Emitter Voltage 6 PIN 1. 2. 3. 4. 5. 6. NC INPUT LED INPUT LED NO CONNECTION EMITTER COLLECTOR BASE TOTAL DEVICE Isolation Surge Voltage(1) (Peak ac Voltage, 60 Hz, 1 sec Duration) Storage Temperature Range(2) Soldering Temperature (10 sec, 1/16 from case) 1. Isolation surge voltage is an internal device dielectric breakdown rating. 1. For this test, Pins 1 and 2 are common, and Pins 4, 5 and 6 are common. 2. Refer to Quality and Reliability Section in Opto Data Book for information on test conditions. Preferred devices are Motorola recommended choices for future use and best overall value. GlobalOptoisolator is a trademark of Motorola, Inc. REV 1 Optoelectronics Device Data Motorola Motorola, Inc. 1995 1 ELECTRICAL CHARACTERISTICS (TA = 25C unless otherwise noted)(1) Symbol Min Typ(1) Max Unit VF -- -- -- -- 1.15 1.15 1.3 1.05 1.5 1.8 -- -- Volts CJ -- 20 -- pF ICEO -- -- -- 1 1 1 100 200 -- nA nA A ICBO -- 0.2 -- nA Collector-Emitter Breakdown Voltage (IC = 10 mA) V(BR)CEO 30 45 -- Volts Collector-Base Breakdown Voltage (IC = 100 A) V(BR)CBO 70 100 -- Volts Emitter-Collector Breakdown Voltage (IE = 100 A) V(BR)ECO 5 7.8 -- Volts DC Current Gain (IC = 2 mA, VCE = 5 V) (Typical Value) hFE -- 500 -- -- Collector-Emitter Capacitance (f = 1 MHz, VCE = 0 V) CCE -- 1.7 -- pF Collector-Base Capacitance (f = 1 MHz, VCB = 0 V) CCB -- 20 -- pF Emitter-Base Capacitance (f = 1 MHz, VEB = 0 V) CEB -- 10 -- pF IC (CTR)(2) 2 (20) 1 (10) 5 (50) 10 (100) 5 (50) 2 (20) 10 (100) 15 (150) -- -- -- -- mA (%) -- 0.33 -- 3 -- VCE(sat) -- 0.1 0.4 Volts Isolation Voltage (f = 60 Hz, t = 1 sec)(4) VISO 7500 -- -- Vac(pk) Isolation Resistance (V = 500 V)(4) RISO 1011 -- -- Isolation Capacitance (V = 0 V, f = 1 MHz)(4) CISO -- 0.2 -- pF Characteristic INPUT LED Forward Voltage (IF = 10 mA, either direction) TA = -55C TA = 100C H11AA1,3,4 H11AA2 All devices All devices Capacitance (V = 0 V, f = 1 MHz) OUTPUT TRANSISTOR Collector-Emitter Dark Current (VCE = 10 V) TA = 100C H11AA1,3,4 H11AA2 All devices Collector-Base Dark Current (VCB = 10 V) COUPLED Output Collector Current (IF = 10 mA, VCE = 10 V) " Output Collector Current Symmetry(3) I 2 H11AA1,3,4 + ) 10 mA, VCE + 10 V F C I at I + -10 mA, V + 10 V F C CE at I Collector-Emitter Saturation Voltage (IC = 0.5 mA, IF = 1. 2. 3. 4. H11AA1 H11AA2 H11AA3 H11AA4 "10 mA) Always design to the specified minimum/maximum electrical limits (where applicable). Current Transfer Ratio (CTR) = IC/IF x 100%. This specification guarantees that the higher of the two IC readings will be no more than 3 times the lower at IF = 10 mA. For this test, Pins 1 and 2 are common, and Pins 4, 5 and 6 are common. Motorola Optoelectronics Device Data TYPICAL CHARACTERISTICS PULSE ONLY PULSE OR DC Vin, INPUT VOLTAGE (VOLTS) 2.4 INPUT CURRENT WAVEFORM 1.6 0.8 0 MAXIMUM PEAK OUTPUT CURRENT (1) -0.8 -1.6 MINIMUM PEAK OUTPUT CURRENT (1) -2.4 -600 -200 0 200 600 iF, INSTANANEOUS INPUT CURRENT (mA) -1000 1000 Figure 2. Output Characteristics IC , COLLECTOR CURRENT (mA) 28 24 IF = 10 mA 20 16 5 mA 12 8 2 mA 4 1 mA 0 0 1 2 3 4 5 6 7 8 9 VCE, COLLECTOR-EMITTER VOLTAGE (VOLTS) 10 I C , OUTPUT COLLECTOR CURRENT (NORMALIZED) Figure 1. Input Voltage versus Input Current VCE = 30 V 1 1 0.7 0.5 0.2 0.1 -60 -40 -20 0 20 40 60 80 TA, AMBIENT TEMPERATURE (C) 100 CCB f = 1 MHz 16 14 12 10 8 CEB CLED 6 4 10 V 0.1 20 2 18 10 0 NORMALIZED TO TA = 25C 22 20 NORMALIZED TO: VCE = 10 V TA = 25C 100 7 5 Figure 4. Output Current versus Ambient Temperature C, CAPACITANCE (pF) ICEO, COLLECTOR-EMITTER DARK CURRENT (NORMALIZED) Figure 3. Collector Current versus Collector-Emitter Voltage 10 40 60 80 TA, AMBIENT TEMPERATURE (C) 100 Figure 5. Dark Current versus Ambient Temperature Motorola Optoelectronics Device Data 2 CCE 0 0.01 0.1 1 V, VOLTAGE (VOLTS) 10 100 Figure 6. Capacitances versus Voltage 3 PACKAGE DIMENSIONS -A- 6 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEAD WHEN FORMED PARALLEL. 4 -B- 1 3 F 4 PL C N -T- L K SEATING PLANE J 6 PL 0.13 (0.005) G M E 6 PL D 6 PL 0.13 (0.005) M T A B M M T B M A M DIM A B C D E F G J K L M N INCHES MIN MAX 0.320 0.350 0.240 0.260 0.115 0.200 0.016 0.020 0.040 0.070 0.010 0.014 0.100 BSC 0.008 0.012 0.100 0.150 0.300 BSC 0_ 15 _ 0.015 0.100 MILLIMETERS MIN MAX 8.13 8.89 6.10 6.60 2.93 5.08 0.41 0.50 1.02 1.77 0.25 0.36 2.54 BSC 0.21 0.30 2.54 3.81 7.62 BSC 0_ 15 _ 0.38 2.54 M STYLE 8: PIN 1. 2. 3. 4. 5. 6. LED 1 ANODE/LED 2 CATHODE LED 1 CATHODE/LED 2 ANODE NC EMITTER COLLECTOR BASE CASE 730A-04 ISSUE G -A- 6 4 -B- 1 S NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3 F 4 PL L H C -T- G J K 6 PL E 6 PL 0.13 (0.005) D 6 PL 0.13 (0.005) M T A M B M SEATING PLANE T B M A M CASE 730C-04 ISSUE D 4 M DIM A B C D E F G H J K L S INCHES MIN MAX 0.320 0.350 0.240 0.260 0.115 0.200 0.016 0.020 0.040 0.070 0.010 0.014 0.100 BSC 0.020 0.025 0.008 0.012 0.006 0.035 0.320 BSC 0.332 0.390 MILLIMETERS MIN MAX 8.13 8.89 6.10 6.60 2.93 5.08 0.41 0.50 1.02 1.77 0.25 0.36 2.54 BSC 0.51 0.63 0.20 0.30 0.16 0.88 8.13 BSC 8.43 9.90 *Consult factory for leadform option availability Motorola Optoelectronics Device Data NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEAD WHEN FORMED PARALLEL. -A- 6 4 -B- 1 3 L N F 4 PL C -T- SEATING PLANE G J K DIM A B C D E F G J K L N INCHES MIN MAX 0.320 0.350 0.240 0.260 0.115 0.200 0.016 0.020 0.040 0.070 0.010 0.014 0.100 BSC 0.008 0.012 0.100 0.150 0.400 0.425 0.015 0.040 MILLIMETERS MIN MAX 8.13 8.89 6.10 6.60 2.93 5.08 0.41 0.50 1.02 1.77 0.25 0.36 2.54 BSC 0.21 0.30 2.54 3.81 10.16 10.80 0.38 1.02 D 6 PL E 6 PL 0.13 (0.005) M T A M B M *Consult factory for leadform option availability CASE 730D-05 ISSUE D Motorola Optoelectronics Device Data 5 Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters can and do vary in different applications. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. How to reach us: USA / EUROPE: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036. 1-800-441-2447 JAPAN: Nippon Motorola Ltd.; Tatsumi-SPD-JLDC, Toshikatsu Otsuki, 6F Seibu-Butsuryu-Center, 3-14-2 Tatsumi Koto-Ku, Tokyo 135, Japan. 03-3521-8315 MFAX: RMFAX0@email.sps.mot.com - TOUCHTONE (602) 244-6609 INTERNET: http://Design-NET.com HONG KONG: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852-26629298 6 *H11AA1/D* Motorola Optoelectronics Device Data H11AA1/D