* VMPD-45B Open Frame Power Supply Features *Universal AC input / Full range *Low leakage current 0.3mA *Protections:Short circuit/Over load/Over voltage *Cooling by free air convection *100% full load burn-in test *Fixed switching frequency at 45KHz *3 years warranty CH1 DC output voltage Output V. tolerance Output rated current Output min. range Output max. range Ripple & noise Line regulation Load regulation Rated output power Rated output power Efficiency DC voltage adj. Input voltage range AC current Inrush current Leakage current Overload protection Over voltage protection Temperature coefficient Set up, rise, hold up time Vibration Withstand voltage Isolation resistance Working temp., humidity Storage temp., humidity Dimensions Weight Safety standards EMC standards Notes: CH2 5V 24V 4% 7% 3.2A 1.2A 0.4A 0.2A 5A 1.8A 60mVp-p 150mVp-p 1% 2% 3% 4% 44.8W 52W with 18CFM min. forced air convection 78% CH1: 10% 90~264VAC 47~4403Hz; 120-370VDC 1.2A/115V 0.7A/230V cold start 20A/115V 40A/230V <0.3mA/264VAC 53~75W output power type: Hiccup mode, recovers automatically after fault condition is removed CH1: 5.75~6.75VDC 0.04% / C (0~50C) on +5V output 800ms, 20ms, 20ms/230VAC 800ms, 20ms, 12ms /115VAC 10~500Hz, 2G 3 axes 10min./1 cycle (1 hour each axes) I/P-O/P: 4KVAC, I/P-FG: 1.5KVAC, O/P-FG: 0.5KVAC, for 1 min. I/P-O/P, I/P-FG, O/P-FG: 500VDC / 100M Ohms min. -10C~+60% (refer to output derating curve), 20%-90% RH -20C~+85C, 10%-95% RH 5x3x1.1 inches PCB only (127x76.2x28 mm) 0.44 lbs (0.2 Kgs) UL2601-1, EN60601-1 approved CISPR11 (EN55011), EN61000-4,2,3,4,5,6,8,11, IEC61000-3-2,3 EN60601-1-2, verification 1. All parameters are specified at 230VAC input, rated load, 25C 70% RH ambient 2. Tolerance includes set up tolerance, line regulation, load regulation 3. Ripple & noise are measured at 20MHz by using a 12" twisted pair terminated with a 0.1uF & 47 uF capacitor 4. Line regulation is measured from low line to high line at rated load 5, Each output provides up to maximum current, but total load cannot exceed max. output power 6. Mounting holes M1 and M2 should be grounded for EMI purposes *V-Infinity reserves the right to make changes to its products or to discontinue any product or service without notice, and to advise customers to verify the most up-to-date product information before placing orders. V-Infinity assumes no liability or responsibility for customer's applications using V-Infinity products other than repair or replacing (at V-I's option) V-Infinity products not meeting V-I's published specifications. Nothing will be covered outside of standard product warranty. V-Infinity, LLC, 9615 SW Allen Blvd Suite 103, Beaverton, OR 97005 www.v-infinity.com 1-866-372-1258 * VMPD-45B Open Frame Power Supply Block Diagram Output Derating Static Characteristics Dimensions (mm) V-Infinity, LLC, 9615 SW Allen Blvd Suite 103, Beaverton, OR 97005 www.v-infinity.com 1-866-372-1258