Complete 16-Bit CCD/CIS Signal Processor AD80066 Data Sheet FEATURES GENERAL DESCRIPTION 16-bit, 24 MSPS analog-to-digital converter (ADC) 4-channel operation up to 24 MHz (6 MHz/channel) 3-channel operation up to 24 MHz (8 MHz/channel) Selectable input range: 3 V or 1.5 V peak-to-peak Input clamp circuitry Correlated double sampling 1x~6x programmable gain 300 mV programmable offset Internal voltage reference Multiplexed byte-wide output Optional single-byte output mode 3-wire serial digital interface 3 V/5 V digital I/O compatibility Power dissipation: 490 mW at 24 MHz operation Reduced power mode and sleep mode available 28-lead SSOP package The AD80066 is a complete analog signal processor for imaging applications. It features a 4-channel architecture designed to sample and condition the outputs of linear charged coupled device (CCD) or contact image sensor (CIS) arrays. Each channel consists of an input clamp, correlated double sampler (CDS), offset digitalto-analog converter (DAC), and programmable gain amplifier (PGA), multiplexed to a high performance 16-bit ADC. For maximum flexibility, the AD80066 can be configured as a 4-channel, 3-channel, 2-channel, or 1-channel device. The CDS amplifiers can be disabled for use with sensors that do not require CDS, such as CIS and CMOS sensors. The 16-bit digital output is multiplexed into an 8-bit output word, which is accessed using two read cycles. There is an optional single-byte output mode. The internal registers are programmed through a 3-wire serial interface and enable adjustment of the gain, offset, and operating mode. The AD80066 operates from a 5 V power supply, typically consumes 490 mW of power, and is packaged in a 28-lead SSOP. APPLICATIONS Flatbed document scanners Film scanners Digital color copiers Multifunction peripherals FUNCTIONAL BLOCK DIAGRAM AVDD VINA AVSS CML AVDD AVSS CAPT PGA CDS CAPB DRVDD DRVSS AD80066 BAND GAP REFERENCE 9-BIT DAC VINB PGA CDS 4:1 MUX 16-BIT ADC 16 16:8 MUX 8 DOUT (D[0:7]) 9-BIT DAC CONFIGURATION REGISTER PGA CDS 9-BIT DAC VIND CDS MUX REGISTER PGA CH. A CH. B CH. C CH. D 6 9-BIT DAC OFFSET INPUT CLAMP BIAS CDSCLK1 9 CH. A CH. B CH. C CH. D SCLK DIGITAL CONTROL INTERFACE SLOAD SDATA GAIN REGISTERS OFFSET REGISTERS CDSCLK2 ADCCLK 08552-001 VINC Figure 1. Rev. B Document Feedback Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 (c)2015 Analog Devices, Inc. All rights reserved. Technical Support www.analog.com AD80066 Data Sheet TABLE OF CONTENTS Features .............................................................................................. 1 1-Channel CDS Mode ............................................................... 13 Applications ....................................................................................... 1 1-Channel SHA Mode ............................................................... 13 General Description ......................................................................... 1 Internal Register Map .................................................................... 14 Functional Block Diagram .............................................................. 1 Internal Register Details ................................................................ 15 Revision History ............................................................................... 2 Configuration Register .............................................................. 15 Specifications..................................................................................... 3 Mux Register ............................................................................... 15 Analog Specifications ................................................................... 3 PGA Gain Registers ................................................................... 15 Digital Specifications ................................................................... 4 Offset Registers ........................................................................... 15 Timing Specifications .................................................................. 5 Circuit Operation ........................................................................... 17 Absolute Maximum Ratings ............................................................ 9 Analog Inputs--CDS Mode ...................................................... 17 Thermal Resistance ...................................................................... 9 External Input Coupling Capacitors ........................................ 17 ESD Caution .................................................................................. 9 Analog Inputs--SHA Mode ...................................................... 18 Pin Configuration and Function Descriptions ........................... 10 Programmable Gain Amplifiers (PGA) .................................. 18 Typical Performance Characteristics ........................................... 11 Applications Information .............................................................. 19 Terminology .................................................................................... 12 Circuit and Layout Recommendations ................................... 19 Theory of Operation ...................................................................... 13 Outline Dimensions ....................................................................... 20 4-Channel CDS Mode................................................................ 13 Ordering Guide .......................................................................... 20 4-Channel SHA Mode................................................................ 13 REVISION HISTORY 4/15--Rev. A to Rev. B Changes to Figure 7 .......................................................................... 7 4/10--Revision A: Initial Version Rev. B | Page 2 of 20 Data Sheet AD80066 SPECIFICATIONS ANALOG SPECIFICATIONS TMIN to TMAX, AVDD = 5 V, DRVDD = 5 V, CDS mode, fADCCLK = 24 MHz, fCDSCLK1 = fCDSCLK2 = 6 MHz, PGA gain = 1, unless otherwise noted. Table 1. Parameter MAXIMUM CONVERSION RATE 4-Channel Mode with CDS 3-Channel Mode with CDS 2-Channel Mode with CDS 1-Channel Mode with CDS ACCURACY (ENTIRE SIGNAL PATH) ADC Resolution Integral Nonlinearity (INL) Differential Nonlinearity (DNL) No Missing Codes ANALOG INPUTS Input Signal Range1 Allowable Reset Transient1 Input Limits2 Input Capacitance Input Bias Current AMPLIFIERS PGA Gain Range PGA Gain Resolution2 PGA Gain Monotonicity Programmable Offset Range Programmable Offset Resolution Programmable Offset Monotonicity NOISE AND CROSSTALK Total Output Noise at PGA Minimum Total Output Noise at PGA Maximum Channel-to-Channel Crosstalk @ 24 MSPS @ 12 MSPS POWER SUPPLY REJECTION AVDD = 5 V 0.25 V VOLTAGE REFERENCE (TA = 25C) CAPT - CAPB TEMPERATURE RANGE Operating Storage POWER SUPPLIES AVDD DRVDD OPERATING CURRENT AVDD DRVDD Power-Down Mode Current Min Typ Max 24 24 24 12 MSPS MSPS MSPS MSPS 16 +20/-5 0.5 Guaranteed Bits LSB LSB 1.5/3.0 2.0 V p-p V V pF nA AVSS - 0.3 AVDD + 0.3 10 10 1 5.9 V/V Steps +295 mV Steps 64 Guaranteed -305 512 Guaranteed 9.5 35 LSB rms LSB rms 70 90 dB dB 0.1 % FSR 0.75 V 0 -65 4.5 3.0 5.0 3.3 95 4 300 Rev. B | Page 3 of 20 Unit 70 +150 C C 5.25 5.25 V V mA mA A AD80066 Data Sheet Parameter POWER DISSIPATION 4-Channel Mode at 24 MHz 1-Channel Mode at 12 MHz 4-Channel Mode at 8 MHz, Slow Power Mode3 1 2 3 Min Typ Max Unit 490 300 165 mW mW mW The linear input signal range is up to 3 V p-p when the CCD reference level is clamped to 3 V by the AD80066 input clamp (see Figure 2). The PGA gain is approximately linear-in-dB but varies nonlinearly with register code (see the Programmable Gain Amplifiers (PGA) section for more information). Measured with Bit D1 of the configuration register set high for 8 MHz, low power operation. AVDD = 5V 1.5V OR 3V p-p MAX INPUT SIGNAL RANGE GND 08552-002 3V BIAS SET BY INPUT CLAMP 2V TYP RESET TRANSIENT Figure 2. Input Signal with the CCD Reference Level Clamped to 3 V DIGITAL SPECIFICATIONS TMIN to TMAX, AVDD = 5 V, DRVDD = 5 V, CDS mode, fADCCLK = 24 MHz, fCDSCLK1 = fCDSCLK2 = 6 MHz, CL = 10 pF, unless otherwise noted. Table 2. Parameter LOGIC INPUTS High Level Input Voltage Low Level Input Voltage High Level Input Current Low Level Input Current Input Capacitance LOGIC OUTPUTS (DRVDD = 5 V) High Level Output Voltage (IOH = 2 mA) Low Level Output Voltage (IOL = 2 mA) LOGIC OUTPUTS (DRVDD = 3 V) High Level Output Voltage (IOH = 2 mA) Low Level Output Voltage (IOL = 2 mA) Symbol Min VIH VIL IIH IIL CIN 2.0 VOH VOL 4.5 VOH VOL 2.5 Rev. B | Page 4 of 20 Typ Max 0.8 10 10 10 Unit V V A A pF 0.5 V V 0.5 V V Data Sheet AD80066 TIMING SPECIFICATIONS TMIN to TMAX, AVDD = 5 V, DRVDD = 5 V. Table 3. Parameter CLOCK PARAMETERS 4-Channel Pixel Rate 1-Channel Pixel Rate ADCCLK Pulse Width CDSCLK1 Pulse Width CDSCLK2 Pulse Width CDSCLK1 Falling1 to CDSCLK2 Rising ADCCLK Falling to CDSCLK2 Rising CDSCLK2 Rising to ADCCLK Rising CDSCLK2 Falling1 to ADCCLK Falling CDSCLK2 Falling1 to CDSCLK1 Rising Aperture Delay for CDS Clocks SERIAL INTERFACE Maximum SCLK Frequency, Write Operation Maximum SCLK Frequency, Read Operation SLOAD to SCLK Setup Time SCLK to SLOAD Hold Time SDATA to SCLK Rising Setup Time SCLK Rising to SDATA Hold Time SCLK Falling to SDATA Valid DATA OUTPUT Output Delay Latency (Pipeline Delay) 1 Symbol Min tPRA tPRB tADCCLK tC1 tC2 tC1C2 tADC2 tC2ADR tC2ADF tC2C1 tAD 166 83 20 15 15 0 0 5 20 5 fSCLK fSCLK tLS tLH tDS tDH tRDV 50 25 5 5 2 2 10 Typ Max Unit ns ns ns ns ns ns ns ns ns ns ns 2 MHz MHz ns ns ns ns ns tOD 8 3 (fixed) ns Cycles CDSCLKx falling edges should not occur within the first 10 ns following an ADCCLK edge. Timing Diagrams tPRA ANALOG INPUTS PIXEL (n + 1) PIXEL n (A,B,C,D) tAD tC1 tAD tC2C1 CDSCLK1 tC1C2 tC2 tC2ADF CDSCLK2 tADCCLK tC2ADR tADC2 ADCCLK tOD OUTPUT DATA (D[7:0]) B(n - 2) C(n - 2) C(n - 2) D(n - 2) D(n - 2) A(n - 1) A(n - 1) B(n - 1) B(n - 1) C(n - 1) C(n - 1) D(n - 1) D(n - 1) HIGH BYTE LOW BYTE HIGH BYTE LOW BYTE HIGH BYTE LOW BYTE HIGH BYTE LOW BYTE HIGH BYTE Figure 3. 4-Channel CDS Mode Timing Rev. B | Page 5 of 20 LOW BYTE HIGH BYTE LOW BYTE A(n) A(n) HIGH BYTE LOW BYTE B(n) HIGH BYTE 08552-003 tADCCLK AD80066 Data Sheet PIXEL (n + 1) PIXEL n (A, B, C) ANALOG INPUTS PIXEL (n + 2) tAD tAD tC2C1 tC1 tPRA CDSCLK1 tC1C2 tC2 tC2ADF CDSCLK2 tADC2 tADCCLK tC2ADR ADCCLK OUTPUT DATA (D[7:0]) A(n - 2) B(n - 2) B(n - 2) C(n - 2) C(n - 2) A(n - 1) A(n - 1) B(n - 1) B(n - 1) C(n - 1) C(n - 1) HIGH BYTE LOW BYTE LOW BYTE HIGH BYTE LOW BYTE HIGH BYTE HIGH BYTE LOW BYTE LOW BYTE HIGH BYTE A(n) A(n) B(n) B(n) HIGH BYTE LOW BYTE HIGH BYTE LOW BYTE 08552-004 tOD tADCCLK Figure 4. 3-Channel CDS Mode Timing PIXEL n ANALOG INPUTS PIXEL (n + 1) PIXEL (n + 2) tAD tAD tPRA tC2C1 tC1 CDSCLK1 tC1C2 tC2 CDSCLK2 tC2ADR tADC2 tC2ADF ADCCLK CH 1 (n - 2) HIGH BYTE tADCCLK CH 2 (n - 2) LOW BYTE HIGH BYTE CH 1 (n - 1) LOW BYTE HIGH BYTE LOW BYTE Figure 5. 2-Channel CDS Mode Timing Rev. B | Page 6 of 20 CH 1 (n) CH 2 (n - 1) HIGH BYTE LOW BYTE HIGH BYTE LOW BYTE 08552-005 tADCCLK OUTPUT DATA (D[7:0]) Data Sheet AD80066 PIXEL n ANALOG INPUTS PIXEL (n + 1) PIXEL (n + 2) tAD tAD tC1 tC2C1 tPRB CDSCLK1 tC1C2 tC2 CDSCLK2 tC2ADR tC2ADF ADCCLK tADCCLK tADCCLK PIXEL (n - 4) PIXEL (n - 4) PIXEL (n - 3) PIXEL (n - 3) PIXEL (n - 2) PIXEL (n - 2) LOW BYTE HIGH BYTE LOW BYTE HIGH BYTE LOW BYTE HIGH BYTE 08552-006 OUTPUT DATA (D[7:0]) tOD NOTES 1. IN 1-CHANNEL CDS MODE. THE CDSCLK1 FALLING EDGE AND THE CDSCLK2 RISING EDGE MUST OCCUR WHILE ADCCLK IS LOW. Figure 6. 1-Channel CDS Mode Timing PIXEL n (A, B, C, D) PIXEL (n + 1) tAD ANALOG INPUTS tPRA tC2 tC2ADF CDSCLK2 tADCCLK tADC2 tC2ADR ADCCLK OUTPUT DATA (D[7:0]) C(n - 2) D(n - 2) D(n - 2) A(n - 1) A(n - 1) B(n - 1) B(n - 1) C(n - 1) C(n - 1) D(n - 1) D(n - 1) HIGH BYTE LOW BYTE HIGH BYTE LOW BYTE HIGH BYTE LOW BYTE HIGH BYTE LOW BYTE HIGH BYTE Figure 7. 4-Channel SHA Mode Timing Rev. B | Page 7 of 20 LOW BYTE A(n) A(n) B(n) B(n) HIGH BYTE LOW BYTE HIGH BYTE LOW BYTE 08552-007 tOD tADCCLK AD80066 Data Sheet PIXEL n PIXEL (n + 1) tAD ANALOG INPUTS tPRB tC2 CDSCLK2 tC2ADR tC2ADF tADCCLK ADCCLK tADCCLK PIXEL (n - 4) PIXEL (n - 4) PIXEL (n - 3) PIXEL (n - 3) PIXEL (n - 2) PIXEL (n - 2) HIGH BYTE LOW BYTE HIGH BYTE LOW BYTE HIGH BYTE LOW BYTE 08552-008 OUTPUT DATA (D[7:0]) tOD Figure 8. 1-Channel SHA Mode Timing OUTPUT DATA (D[7:0]) HIGH BYTE (DB[15:8]) PIXEL n tOD tOD LOW BYTE (DB[7:0]) HIGH BYTE (DB[15:8]) LOW BYTE (DB[7:0]) LOW BYTE (DB[7:0]) HIGH BYTE (DB[15:8]) PIXEL n PIXEL (n + 1) PIXEL (n + 1) PIXEL (n + 2) PIXEL (n + 3) 08552-009 ADCCLK Figure 9. Digital Output Data Timing ADCCLK OUTPUT DATA (D[7:0]) HIGH BYTE (DB[15:8]) HIGH BYTE (DB[15:8]) HIGH BYTE (DB[15:8]) PIXEL n PIXEL (n + 1) PIXEL (n + 2) 08552-010 tOD Figure 10. Single-Byte Mode Digital Output Data Timing SDATA R/W A3 A2 A1 tDH A0 D8 D7 D6 D5 D4 D3 D2 D1 D0 tDS SCLK tLS 08552-011 tLH SLOAD Figure 11. Serial Write Operation Timing SDATA R/W A3 A2 A1 A0 D8 D7 D6 D5 D4 D3 D2 D1 D0 tRDV SCLK tLH 08552-012 tL S SLOAD Figure 12. Serial Read Operation Timing Rev. B | Page 8 of 20 Data Sheet AD80066 ABSOLUTE MAXIMUM RATINGS THERMAL RESISTANCE Table 4. Parameter VINx, CAPT, CAPB Digital Inputs SDATA AVDD DRVDD AVSS Digital Outputs (D[7:0]) Temperature Junction Storage Lead (10 sec) With Respect To AVSS AVSS DRVSS AVSS DRVSS DRVSS DRVSS Rating -0.3 V to AVDD + 0.3 V -0.3 V to AVDD + 0.3 V -0.3 V to DRVDD -0.5 V to +6.5 V -0.5 V to +6.5 V -0.3 V to +0.3 V -0.3 V to DRVDD + 0.3 V JA is specified for the worst-case conditions, that is, a device soldered in a circuit board for surface-mount packages. Table 5. Thermal Resistance Package Type 28-Lead, 5.3 mm SSOP ESD CAUTION 150C -65C to +150C 300C Stresses at or above those listed under Absolute Maximum Ratings may cause permanent damage to the product. This is a stress rating only; functional operation of the product at these or any other conditions above those indicated in the operational section of this specification is not implied. Operation beyond the maximum operating conditions for extended periods may affect product reliability. Rev. B | Page 9 of 20 JA 109 JC 39 Unit C/W AD80066 Data Sheet 28 AVSS CDSCLK1 AVDD 1 2 27 VINA CDSCLK2 3 26 OFFSET ADCCLK 4 25 VINB DRVDD 5 24 CML DRVSS 6 23 VINC AD80066 22 CAPT TOP VIEW (Not to Scale) 21 CAPB D5 9 20 VIND D4 10 19 AVSS D3 11 18 AVDD D2 12 17 SLOAD D1 13 16 SCLK (LSB) D0 14 15 SDATA (MSB) D7 7 D6 8 08552-013 PIN CONFIGURATION AND FUNCTION DESCRIPTIONS Figure 13. Pin Configuration Table 6. Pin Function Descriptions Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 1 Mnemonic AVDD CDSCLK1 CDSCLK2 ADCCLK DRVDD DRVSS D7 (MSB) D6 D5 D4 D3 D2 D1 D0 (LSB) SDATA SCLK SLOAD AVDD AVSS VIND CAPB CAPT VINC CML VINB OFFSET VINA AVSS Type1 P DI DI DI P P DO DO DO DO DO DO DO DO DI/DO DI DI P P AI AO AO AI AO AI AO AI P Description 5 V Analog Supply. CDS Reference Level Sampling Clock. CDS Data Level Sampling Clock. ADC Sampling Clock. Digital Output Driver Supply (3 V or 5 V). Digital Output Driver Ground. Data Output MSB. ADC DB15 high byte; ADC DB7 low byte. Data Output. ADC DB14 high byte; ADC DB6 low byte. Data Output. ADC DB13 high byte; ADC DB5 low byte. Data Output. ADC DB12 high byte; ADC DB4 low byte. Data Output. ADC DB11 high byte; ADC DB3 low byte. Data Output. ADC DB10 high byte; ADC DB2 low byte. Data Output. ADC DB9 high byte; ADC DB1 low byte. Data Output LSB. ADC DB8 high byte; ADC DB0 low byte. Serial Interface Data Input/Output. Serial Interface Clock Input. Serial Interface Load Pulse. 5 V Analog Supply. Analog Ground. Analog Input, D Channel. ADC Bottom Reference Voltage Decoupling. ADC Top Reference Voltage Decoupling. Analog Input, C Channel. Internal Bias Level Decoupling. Analog Input, B Channel. Clamp Bias Level Decoupling. Analog Input, A Channel. Analog Ground. AI = analog input, AO = analog output, DI = digital input, DO = digital output, and P = power. Rev. B | Page 10 of 20 Data Sheet AD80066 1.0 15 0.5 10 INL (LSB) 0 -0.5 0 12,800 25,600 38,400 51,200 64,000 ADC OUTPUT CODE 08552-014 0 -1.0 50 45 40 35 30 25 20 15 10 0 15 30 45 PGA REGISTER VALUE (Decimal) 63 08552-015 5 0 -5 0 12,800 25,600 38,400 51,200 ADC OUTPUT CODE Figure 16. Typical INL Performance Figure 14. Typical DNL Performance OUTPUT NOISE (LSB) 5 Figure 15. Output Noise vs. PGA Gain Rev. B | Page 11 of 20 64,000 08552-016 DNL (LSB) TYPICAL PERFORMANCE CHARACTERISTICS AD80066 Data Sheet TERMINOLOGY Integral Nonlinearity (INL) Integral nonlinearity error refers to the deviation of each individual code from a line drawn from zero scale through positive full scale. The point used as zero scale occurs 1/2 LSB before the first code transition. Positive full scale is defined as a level 11/2 LSB beyond the last code transition. The deviation is measured from the middle of each particular code to the true straight line. Differential Nonlinearity (DNL) An ideal ADC exhibits code transitions that are exactly 1 LSB apart. DNL is the deviation from this ideal value; therefore, every code must have a finite width. No missing codes guaranteed to 16-bit resolution indicates that all 65,536 codes must be present over all operating ranges. Offset Error The first ADC code transition should occur at a level 1/2 LSB above the nominal zero-scale voltage. The offset error is the deviation of the actual first code transition level from the ideal level. Gain Error The last code transition should occur for an analog value 11/2 LSB below the nominal full-scale voltage. Gain error is the deviation of the actual difference between the first and last code transitions and the ideal difference between the first and last code transitions. Input-Referred Noise The rms output noise is measured using histogram techniques. The standard deviation of the ADC output codes is calculated in LSB and converted to an equivalent voltage, using the relationship 1 LSB = 1.5 V/65,536 = 23 V. The noise is then referred to the input of the AD80066 by dividing by the PGA gain. Channel-to-Channel Crosstalk In an ideal 3-channel system, the signal in one channel does not influence the signal level of another channel. The channel-tochannel crosstalk specification is a measure of the change that occurs in one channel as the other two channels are varied. In the AD80066, one channel is grounded and the other two channels are exercised with full-scale input signals. The change in the output codes from the first channel is measured and compared with the result when all three channels are grounded. The difference is the channel-to-channel crosstalk, stated in LSB. Aperture Delay The aperture delay is the delay that occurs from when a sampling edge is applied to the AD80066 until the actual sample of the input signal is held. Both CDSCLK1 and CDSCLK2 sample the input signal during the transition from high to low; therefore, the aperture delay is measured from each falling edge of the clock to when the internal sample is taken. Power Supply Rejection The power supply rejection specifies the maximum full-scale change that occurs from the initial value when the supplies are varied over the specified limits. Rev. B | Page 12 of 20 Data Sheet AD80066 THEORY OF OPERATION The AD80066 can be operated in several different modes, including 4-channel CDS mode, 4-channel SHA mode, 1-channel CDS mode, and 1-channel SHA mode. Each mode is selected by programming the configuration register through the serial interface. For more information on CDS or SHA mode operation, see the Circuit Operation section. 4-CHANNEL CDS MODE In 4-channel CDS mode, the AD80066 simultaneously samples the A, B, C, and D input voltages from the CCD outputs. The sampling points for each CDS are controlled by CDSCLK1 and CDSCLK2 (see Figure 17 and Figure 18). The CDSCLK1 falling edge samples the reference level of the CCD waveform, and the CDSCLK2 falling edge samples the data level of the CCD waveform. Each CDS amplifier outputs the difference between the CCD reference level and the data level. The output voltage of each CDS amplifier is then level-shifted by an offset DAC. The voltages are scaled by the four PGAs before being multiplexed through the 16-bit ADC. The ADC sequentially samples the PGA outputs on the falling edges of ADCCLK. The offset and gain values for the A, B, C, and D channels are programmed using the serial interface. The order in which the channels are switched through the multiplexer is selected by programming the mux register. Timing for this mode is shown in Figure 3. The falling edge of CDSCLK2 should occur coincident with or before the rising edge of ADCCLK. However, this is not required to satisfy the minimum timing constraints. The rising edge of CDSCLK2 should not occur before the previous falling edge of ADCCLK, as shown by tADC2. The output data latency is 3 ADCCLK cycles. 4-CHANNEL SHA MODE In 4-channel SHA mode, the AD80066 simultaneously samples the A, B, C, and D input voltages. The sampling point is controlled by CDSCLK2. The falling edge of CDSCLK2 samples the input waveforms on each channel. The output voltages from the three SHAs are modified by the offset DACs and then scaled by the four PGAs. The outputs of the PGAs are then multiplexed through the 16-bit ADC. The ADC sequentially samples the PGA outputs on the falling edges of ADCCLK. The input signal is sampled with respect to the voltage applied to the OFFSET pin (see Figure 19). With the OFFSET pin grounded, a 0 V input corresponds to the zero-scale output of the ADC. The OFFSET pin can also be used as a coarse offset adjustment pin. A voltage applied to this pin is subtracted from the voltages applied to the A, B, C, and D inputs in the first amplifier stage of the AD80066. The input clamp is disabled in this mode. For more information, see the Analog Inputs--SHA Mode section. The offset and gain values for the A, B, C, and D channels are programmed using the serial interface. The order in which the channels are switched through the multiplexer is selected by programming the mux register. Timing for this mode is shown in Figure 7. The CDSCLK1 pin should be grounded in this mode. Although not required, the falling edge of CDSCLK2 should occur coincident with or before the rising edge of ADCCLK. The rising edge of CDSCLK2 should not occur before the previous falling edge of ADCCLK, as shown by tADC2. The output data latency is 3 ADCCLK cycles. 1-CHANNEL CDS MODE The 1-channel CDS mode operates in the same way as the 4-channel CDS mode, except the multiplexer remains fixed. Only the channel specified in the mux register is processed. Timing for this mode is shown in Figure 6. 1-CHANNEL SHA MODE The 1-channel SHA mode operates in the same way as the 4-channel SHA mode, except the multiplexer remains fixed. Only the channel specified in the mux register is processed. Timing for this mode is shown in Figure 8. The CDSCLK1 pin should be grounded in this mode of operation. Rev. B | Page 13 of 20 AD80066 Data Sheet INTERNAL REGISTER MAP Table 7. Internal Register Map Register Name Configuration Mux Gain A Gain B Gain C Gain D Offset A Offset B Offset C Offset D A3 0 0 0 0 0 0 0 0 1 1 Address A2 A1 0 0 0 0 0 1 0 1 1 0 1 0 1 1 1 1 0 0 0 0 A0 0 1 0 1 0 1 0 1 0 1 D8 0 0 0 0 0 0 MSB MSB MSB MSB D7 0 0 0 0 0 0 D6 0 0 0 0 0 0 D5 VREF 0 MSB MSB MSB MSB D4 2/1 byte Ch. order Rev. B | Page 14 of 20 Data Bits D3 CDS on Ch. A D2 Input range Ch. B D1 Fast/slow Ch. C D0 Power on Ch. D LSB LSB LSB LSB LSB LSB LSB LSB Data Sheet AD80066 INTERNAL REGISTER DETAILS the CDSCLK2 pulse always resets the multiplexer to sample the A channel first. When Bit D4 is set high, the channel order is reversed to D, C, B, and A. The CDSCLK2 pulse always resets the multiplexer to sample the D channel first. Bits D[3:0] are used when operating in 1-channel mode. Bit D3 is set high to sample the A channel. Bit D2 is set high to sample the B channel. Bit D1 is set high to sample the C channel. Bit D0 is set high to sample the D channel. The multiplexer remains stationary in 1-channel mode. CONFIGURATION REGISTER The configuration register controls the AD80066 operating mode and bias levels. The D8, D7, and D6 bits should always be set low. Bit D2 sets the full-scale input voltage range of the AD80066 ADC to either 3 V (high) or 1.5 V (low). Bit D5 controls the internal voltage reference. If the AD80066 internal voltage reference is used, this bit is set low. Setting Bit D5 high disables the internal voltage reference, allowing an external voltage reference to be used. Setting Bit D3 low enables the CDS mode of operation and setting this bit high enables the SHA mode of operation. If Bit D4 is set high, the 16-bit ADC output is multiplexed into two bytes. The most significant byte is output on the ADCCLK rising edge, and the least significant byte is output on the ADCCLK falling edge (see Figure 10). If Bit D1 is set high, the AD80066 is configured for slow operation (8 MHz) to reduce power consumption. Bit D0 controls the power-down mode. Setting Bit D0 low places the AD80066 into a very low power sleep mode. All register contents are retained while the AD80066 is in the power-down state. PGA GAIN REGISTERS There are four PGA registers for individually programming the gain for the A, B, C, and D channels. The D8, D7, and D6 bits in each register must be set low, and the D5 through D0 bits control the gain range in 64 increments. See Figure 22 for the PGA gain vs. the PGA register value. The coding for the PGA registers is straight binary, with a word of all 0s corresponding to the minimum gain setting (1x) and a word of all 1s corresponding to the maximum gain setting (5.9x). OFFSET REGISTERS MUX REGISTER There are four offset registers for individually programming the offset in the A, B, C, and D channels. The D8 through D0 bits control the offset range from -300 mV to +300 mV in 512 increments. The coding for the offset registers is sign magnitude, with D8 as the sign bit. Table 11 shows the offset range as a function of the D8 through D0 bits. The mux register controls the sampling channel order in the AD80066. The D8, D7, D6, and D5 bits should always be set low. Bit D4 is used when operating in 4-channel mode. Setting Bit D4 low sequences the multiplexer to sample the A channel first, and then the B, C, and D channels. When in this mode, Table 8. Configuration Register Settings D8 Set to 0 1 D7 Set to 0 D6 Set to 0 D5 Internal voltage reference 1 = disabled 0 = enabled1 D4 2/1 byte output D3 CDS operation D2 Input range D1 Fast/slow D0 Power mode 1 = one byte 0 = two bytes1 1 = SHA mode 0 = CDS mode1 1=3V 0 = 1.5 V1 1 = 8 MHz 0 = 24 MHz1 1 = on (normal) 0 = off1 Power-on default. Table 9. Mux Register Settings D8 Set to 0 1 D7 Set to 0 D6 Set to 0 D5 Set to 0 D4 Mux order 1 = D, C, B, A 0 = A, B, C, D1 D3 Channel A 1 = channel used 0 = not used1 D2 Channel B 1 = channel used 0 = not used1 D1 Channel C 1 = channel used 0 = not used1 D0 Channel D 1 = channel used 0 = not used1 Power-on default. Table 10. PGA Gain Register Settings D81 0 0 ... 0 0 1 2 D71 0 0 ... 0 0 D61 0 0 ... 0 0 (MSB) D5 0 0 ... 1 1 D4 0 0 ... 1 1 D3 0 0 ... 1 1 D2 0 0 ... 1 1 Must be set to 0. Power-on default. Rev. B | Page 15 of 20 D1 0 0 ... 1 1 (LSB) D0 02 1 ... 0 1 Gain (V/V) 1.0 1.013 ... 5.56 5.9 Gain (dB) 0.0 0.12 ... 14.9 15.56 AD80066 Data Sheet Table 11. Offset Register Settings (MSB) D8 0 0 ... 0 1 1 ... 1 1 D7 0 0 ... 1 0 0 ... 1 D6 0 0 ... 1 0 0 ... 1 D5 0 0 ... 1 0 0 ... 1 D4 0 0 ... 1 0 0 ... 1 D3 0 0 ... 1 0 0 ... 1 D2 0 0 ... 1 0 0 ... 1 Power-on default value. Rev. B | Page 16 of 20 D1 0 0 ... 1 0 0 ... 1 (LSB) D0 01 1 ... 1 0 1 ... 1 Offset (mV) 0 +1.2 ... +300 0 -1.2 ... -300 Data Sheet AD80066 CIRCUIT OPERATION ANALOG INPUTS--CDS MODE EXTERNAL INPUT COUPLING CAPACITORS Figure 17 shows the analog input configuration for the CDS mode of operation. Figure 18 shows the internal timing for the sampling switches. The CCD reference level is sampled when CDSCLK1 transitions from high to low, opening S1. The CCD data level is sampled when CDSCLK2 transitions from high to low, opening S2. S3 is then closed, generating a differential output voltage that represents the difference between the two sampled levels. The recommended value for the input coupling capacitors is 0.1 F. Although it is possible to use a smaller capacitor, this larger value is preferable for several reasons: The input clamp is controlled by CDSCLK1. When CDSCLK1 is high, S4 closes and the internal bias voltage is connected to the analog input. The bias voltage charges the external 0.1 F input capacitor, level-shifting the CCD signal into the input common-mode range of the AD80066. The time constant of the input clamp is determined by the internal 5 k resistance and the external 0.1 F input capacitance. AD80066 S1 VINA CCD SIGNAL 2pF CML CIN 0.1F S3 5k S2 AVDD S4 1.7k OFFSET 1F + CML 2pF 0.1F 2.2k 3V 08552-017 6.9k Figure 17. CDS Mode Input Configuration (All Four Channels Are Identical) S1, S4 CLOSED S1, S4 CLOSED S1, S4 OPEN S2 CLOSED CDSCLK2 S2 OPEN Q3 (INTERNAL) S3 OPEN S2 CLOSED S3 CLOSED S3 CLOSED 08552-018 CDSCLK1 Figure 18. CDS Mode Internal Switch Timing Rev. B | Page 17 of 20 Signal attenuation: The input coupling capacitor creates a capacitive divider using the input capacitance from an integrated CMOS circuit, which, in turn, attenuates the CCD signal level. CIN should be large relative to the 10 pF input capacitance of the IC in order to minimize this effect. Linearity: Some of the input capacitance of a CMOS IC is junction capacitance, which varies nonlinearly with applied voltage. If the input coupling capacitor is too small, the attenuation of the CCD signal varies nonlinearly with signal level. This degrades the system linearity performance. Sampling errors: The internal 2 pF sampling capacitors retain a memory of the previously sampled pixel. There is a charge redistribution error between CIN and the internal sample capacitors for larger pixel-to-pixel voltage swings. As the value of CIN is reduced, the resulting error in the sampled voltage increases. With a CIN value of 0.1 F, the charge redistribution error is less than 1 LSB for a full-scale, pixelto-pixel voltage swing. AD80066 Data Sheet ANALOG INPUTS--SHA MODE AD80066 Figure 19 shows the analog input configuration for the SHA mode of operation. Figure 20 shows the internal timing for the sampling switches. The input signal is sampled when CDSCLK2 transitions from high to low, opening S1. The voltage on the OFFSET pin is also sampled on the falling edge of CDSCLK2, when S2 opens. S3 is then closed, generating a differential output voltage that represents the difference between the sampled input voltage and the OFFSET voltage. The input clamp is disabled during SHA mode operation. VINA VOLTAGE REFERENCE FROM CIS MODULE AVDD OFFSET 2pF PROGRAMMABLE GAIN AMPLIFIERS (PGA) CML The AD80066 uses one PGA for each channel. Each PGA has a gain range from 1x (0 dB) to 5.8x (15.5 dB), adjustable in 64 steps. Figure 22 shows the PGA gain as a function of the PGA register value. Although the gain curve is approximately linear-in-dB, the gain in V/V varies nonlinearly with register code, following the equation CML VINC CML C CML VIND Gain D 08552-019 CML CML Figure 19. SHA Mode Input Configuration (All Four Channels Are Identical) S1, S2 CLOSED 5.9 63 G 1 4.9 63 where G is the decimal value of the gain register contents and varies from 0 to 63. S1, S2 CLOSED 15 5.9 12 5.0 9 4.0 6 3.0 3 2.0 Figure 21 shows how the OFFSET pin can be used in a CIS application for coarse offset adjustment. Many CIS signals have dc offsets ranging from several hundred millivolts to more than 1 V. By connecting the appropriate dc voltage to the OFFSET pin, the large dc offset is removed from the CIS signal. Then, the signal can be scaled using the PGA to maximize the dynamic range of the ADC. 0 0 4 1.0 8 12 16 20 24 28 32 36 40 44 48 52 56 60 63 PGA REGISTER VALUE (Decimal) Figure 22. PGA Gain Transfer Function Rev. B | Page 18 of 20 08552-022 Figure 20. SHA Mode Internal Switch Timing GAIN (dB) S3 OPEN 08552-020 S3 CLOSED GAIN (V/V) S1, S2 OPEN S3 CLOSED Q3 (INTERNAL) 0.1F Figure 21. SHA Mode Used with External DC Offset B CDSCLK2 OFFSET A CML VINB C OFFSET 08552-021 S2 OPTIONAL DC OFFSET (OR CONNECT TO GND) SHA R2 CML S3 B OFFSET DC OFFSET 2pF INPUT SIGNAL SHA VINC R1 S1 A OFFSET VINB AD80066 VINA SHA Data Sheet AD80066 APPLICATIONS INFORMATION CIRCUIT AND LAYOUT RECOMMENDATIONS CDSCLK2 should occur coincident with or before the rising edge of ADCCLK (see Figure 3 through Figure 8 for timing). All 0.1 F decoupling capacitors should be located as close as possible to the AD80066 pins. When operating in 1-channel mode, the unused analog inputs should be grounded. Figure 23 shows the recommended circuit configuration for 4-channel CDS mode operation. The recommended input coupling capacitor value is 0.1 F (see the Analog Inputs--CDS Mode section). A single ground plane is recommended for the AD80066. A separate power supply can be used for DRVDD, the digital driver supply, but this supply pin should still be decoupled to the same ground plane as the rest of the AD80066. The loading of the digital outputs should be minimized, either by using short traces to the digital ASIC or by using external digital buffers. To minimize the effect of digital transients during major output code transitions, the falling edge of Figure 24 shows the recommended circuit configuration for 4-channel SHA mode. All of the previously explained considerations also apply to this configuration, except that the analog input signals are directly connected to the AD80066 without the use of coupling capacitors. Before connecting the signals, the analog input signals must be dc-biased between 0 V and 1.5 V or 3 V (see the Analog Inputs--SHA Mode section). 5V 0.1F 0.1F A INPUT 0.1F AVDD CDSCLK1 CDSCLK2 3.3V ADCCLK DRVDD DRVSS 0.1F (MSB) D7 D6 D5 D4 D3 D2 D1 (LSB) D0 1 28 2 27 3 26 4 25 5 24 6 23 AD80066 7 22 B INPUT AVSS VINA OFFSET VINB CML 0.1F VINC C INPUT 0.1F CAPT TOP VIEW (Not to Scale) 21 CAPB VIND 8 9 1.0F 0.1F 0.1F 0.1F 10F 0.1F 20 10 19 11 18 12 17 13 16 14 15 0.1F AVSS D INPUT AVDD 0.1F SLOAD SCLK 5V SDATA DATA INPUTS 08552-023 CLOCK INPUTS SERIAL INTERFACE Figure 23. Recommended Circuit Configuration, 4-Channel CDS Mode 5V 0.1F 2 CLOCK INPUTS CDSCLK1 CDSCLK2 3.3V ADCCLK DRVDD 0.1F DRVSS (MSB) D7 D6 D5 D4 D3 D2 D1 (LSB) D0 1 28 2 27 3 26 4 25 5 24 6 7 23 AD80066 22 TOP VIEW 8 (Not to Scale) 21 9 10 20 19 11 18 12 17 13 16 14 15 B INPUT AVSS VINA OFFSET VINB CML 0.1F VINC C INPUT 0.1F CAPT CAPB 0.1F 10F VIND 0.1F D INPUT AVSS AVDD SLOAD 0.1F SCLK SDATA DATA INPUTS 5V SERIAL INTERFACE 08552-024 AVDD A INPUT Figure 24. Recommended Circuit Configuration, 4-Channel SHA Mode (Analog Inputs Sampled with Respect to Ground) Rev. B | Page 19 of 20 AD80066 Data Sheet OUTLINE DIMENSIONS 10.50 10.20 9.90 15 28 5.60 5.30 5.00 1 8.20 7.80 7.40 14 0.65 BSC 0.38 0.22 SEATING PLANE 8 4 0 COMPLIANT TO JEDEC STANDARDS MO-150-AH 0.95 0.75 0.55 060106-A 0.05 MIN COPLANARITY 0.10 0.25 0.09 1.85 1.75 1.65 2.00 MAX Figure 25. 28-Lead Shrink Small Outline Package [SSOP] (RS-28) Dimensions shown in millimeters ORDERING GUIDE Model1 AD80066KRSZ AD80066KRSZRL 1 Temperature Range 0C to 70C 0C to 70C Package Description 28-Lead SSOP 28-Lead SSOP Z = RoHS Compliant Part. (c)2015 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D08552-0-4/15(B) Rev. B | Page 20 of 20 Package Option RS-28 RS-28