HA5022 - Intersil Corporation - Datasheet.Directory

CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.

HA5022

Dual, 125MHz, Video Current Feedback

Ampliﬁer with Disable

The HA5022 is a dual version of thepopular Intersil HA5020.

It features wide bandwidth and high slew rate, and is

optimized for video applications and gains between 1 and

10. It is a current feedback ampliﬁer and thus yields less

bandwidth degradation at high closed loop gains than

voltage feedback ampliﬁers.

The low differential gain and phase, 0.1dB gain ﬂatness, and

ability to drive two back terminated 75Ωcables, make this

ampliﬁer ideal for demanding video applications.

The HA5022 also features a disable function that

signiﬁcantly reduces supply current while forcing the output

to a true high impedance state. This functionality allows 2:1

video multiplex ers to be implemented with a single IC.

The current feedback design allows the user to take

advantage of the ampliﬁer’s bandwidth dependency on the

feedback resistor. By reducing RF, the bandwidth can be

increased to compensate for decreases at higher closed

loop gains or heavy output loads.

Features

• Dual Version of HA-5020

• Individual Output Enable/Disable

• Input Offset Voltage . . . . . . . . . . . . . . . . . . . . . . . . 800µV

• Wide Unity Gain Bandwidth . . . . . . . . . . . . . . . . . 125MHz

• Slew Rate. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 475V/µs

• Differential Gain . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.03%

• Differential Phase. . . . . . . . . . . . . . . . . . . . 0.03 Degrees

• Supply Current (per Ampliﬁer) . . . . . . . . . . . . . . . . 7.5mA

• ESD Protection. . . . . . . . . . . . . . . . . . . . . . . . . . . . 4000V

• Guaranteed Speciﬁcations at ±5V Supplies

Applications

• Video Multiplexers; Video Switching and Routing

• Video Gain Block

• Video Distribution Ampliﬁer/RGB Ampliﬁer

• Flash A/D Driver

• Current to Voltage Converter

• Medical Imaging

• Radar and Imaging Systems

Pinout

HA5022

(PDIP, SOIC)

TOP VIEW

Ordering Information

PART NUMBER TEMP.

RANGE (oC) PACKAGE PKG.

NO.

HA5022IP -40 to 85 16 Ld PDIP E16.3

HA5022IB -40 to 85 16 Ld SOIC M16.15

HA5022EVAL High Speed Op Amp DIP Evaluation Board

-IN1

+IN1

DIS1

V-

DIS2

+IN2

-IN2

OUT1

V+

OUT2

Data Sheet May 1999 File Number

3392.6

Absolute Maximum Ratings Thermal Information

Voltage Between V+ and V- Terminals. . . . . . . . . . . . . . . . . . . . 36V

DC Input Voltage (Note 3) . . . . . . . . . . . . . . . . . . . . . . . . ±VSUPPLY

Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10V

Output Current (Note 4). . . . . . . . . . . . . . . . .Short Circuit Protected

ESD Rating (Note 3)

Human Body Model (Per MIL-STD-883 Method 3015.7) . . 2000V

Operating Conditions

Temperature Range. . . . . . . . . . . . . . . . . . . . . . . . . . -40oC to 85oC

Supply Voltage Range (Typical). . . . . . . . . . . . . . . . . ±4.5V to ±15V

Thermal Resistance (Typical, Note 2) θJA (oC/W)

PDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90

SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115

Maximum Junction Temperature (Note 1) . . . . . . . . . . . . . . . . .175oC

Maximum Junction Temperature (Plastic Package, Note 1) . .150oC

Maximum Storage Temperature Range. . . . . . . . . . -65oC to 150oC

Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300oC

(SOIC - Lead Tips Only)

CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operationofthe

device at these or any other conditions above those indicated in the operational sections of this speciﬁcation is not implied.

NOTES:

1. Maximum power dissipation, including output load, must be designed to maintain junction temperature below 175oC for die, and below 150oC

for plastic packages. See Application Information section for safe operating area information.

2. θJA is measured with the component mounted on an evaluation PC board in free air.

3. The non-inverting input of unused amplifiers must be connected to GND.

4. Output is protected for short circuits to ground. Brief short circuits to ground will not degrade reliability, however, continuous (100% duty cycle)

output current should not exceed 15mA for maximum reliability.

Electrical Speciﬁcations VSUPPLY = ±5V, RF = 1kΩ, AV = +1, RL = 400Ω, CL≤10pF, Unless Otherwise Specified

PARAMETER TEST

CONDITIONS

(NO TE 11)

TEST

LEVEL TEMP.

(oC) MIN TYP MAX UNITS

INPUT CHARACTERISTICS

Input Offset Voltage (VIO) A 25 - 0.8 3 mV

A Full - - 5 mV

Delta VIO Between Channels A Full - 1.2 3.5 mV

Average Input Offset Voltage Drift B Full - 5 - µV/oC

VIO Common Mode Rejection Ratio Note 5 A 25 53 - - dB

A Full 50 - - dB

VIO Power Supply Rejection Ratio ±3.5V ≤ VS≤±6.5V A 25 60 - - dB

A Full 55 - - dB

Input Common Mode Range Note 5 A Full ±2.5 - - V

Non-Inverting Input (+IN) Current A 25 - 3 8 µA

A Full - - 20 µA

+IN Common Mode Rejection

(+IBCMR =) Note 5 A 25 - - 0.15 µA/V

A Full - - 0.5 µA/V

+IN Power Supply Rejection ±3.5V ≤ VS≤±6.5V A 25 - - 0.1 µA/V

A Full - - 0.3 µA/V

Inverting Input (-IN) Current A 25, 85 - 4 12 µA

A -40 - 10 30 µA

Delta -IN BIAS Current Between

Channels A 25, 85 - 6 15 µA

A -40 - 10 30 µA

-IN Common Mode Rejection Note 5 A 25 - - 0.4 µA/V

A Full - - 1.0 µA/V

+RIN

HA5022

-IN Power Supply Rejection ±3.5V ≤ VS≤±6.5V A 25 - - 0.2 µA/V

A Full - - 0.5 µA/V

Input Noise Voltage f = 1kHz B 25 - 4.5 - nV/√Hz

+Input Noise Current f = 1kHz B 25 - 2.5 - pA/√Hz

-Input Noise Current f = 1kHz B 25 - 25.0 - pA/√Hz

TRANSFER CHARACTERISTICS

Transimpedance Note 16 A 25 1.0 - - MΩ

A Full 0.85 - - MΩ

Open Loop DC Voltage Gain RL = 400Ω, VOUT = ±2.5V A 25 70 - - dB

A Full 65 - - dB

Open Loop DC Voltage Gain RL = 100Ω, VOUT = ±2.5V A 25 50 - - dB

A Full 45 - - dB

OUTPUT CHARACTERISTICS

Output Voltage Swing RL = 150ΩA25±2.5 ±3.0 - V

A Full ±2.5 ±3.0 - V

Output Current RL = 150ΩB Full ±16.6 ±20.0 - mA

Output Current, Short Circuit VIN = ±2.5V, VOUT = 0V A Full ±40 ±60 - mA

Output Current, Disabled VOUT = ±2.5V, VIN = 0V,

DISABLE = 0V A Full - - 2 µA

Output Disable Time Note 12 B 25 - 40 - µs

Output Enable Time Note 13 B 25 - 40 - ns

Output Capacitance, Disabled Note 14 B 25 - 15 - pF

POWER SUPPLY CHARACTERISTICS

Supply Voltage Range A 25 5 - 15 V

Quiescent Supply Current A Full - 7.5 10 mA/Op Amp

Supply Current, Disabled DISABLE = 0V A Full - 5 7.5 mA/Op Amp

Disable Pin Input Current DISABLE = 0V A Full - 1.0 1.5 mA

Minimum Pin 8 Current to Disable Note 6 A Full 350 - - µA

Maximum Pin 8 Current to Enable Note 7 A Full - - 20 µA

AC CHARACTERISTICS (AV = +1)

Slew Rate Note 8 B 25 275 400 - V/µs

Full Power Bandwidth Note 9 B 25 22 28 - MHz

Rise Time Note 10 B 25 - 6 - ns

Fall Time Note 10 B 25 - 6 - ns

Propagation Delay Note 10 B 25 - 6 - ns

Overshoot B 25 - 4.5 - %

-3dB Bandwidth VOUT = 100mV B 25 - 125 - MHz

Settling Time to 1% 2V Output Step B 25 - 50 - ns

Settling Time to 0.25% 2V Output Step B 25 - 75 - ns

Electrical Speciﬁcations VSUPPLY = ±5V, RF = 1kΩ, AV = +1, RL = 400Ω, CL≤10pF, Unless Otherwise Specified (Continued)

PARAMETER TEST

CONDITIONS

(NO TE 11)

TEST

LEVEL TEMP.

(oC) MIN TYP MAX UNITS

HA5022

AC CHARACTERISTICS (AV = +2, RF = 681Ω)

Slew Rate Note 8 B 25 - 475 - V/µs

Full Power Bandwidth Note 9 B 25 - 26 - MHz

Rise Time Note 10 B 25 - 6 - ns

Fall Time Note 10 B 25 - 6 - ns

Propagation Delay Note 10 B 25 - 6 - ns

Overshoot B 25 - 12 - %

-3dB Bandwidth VOUT = 100mV B 25 - 95 - MHz

Settling Time to 1% 2V Output Step B 25 - 50 - ns

Settling Time to 0.25% 2V Output Step B 25 - 100 - ns

Gain Flatness 5MHz B 25 - 0.02 - dB

20MHz B 25 - 0.07 - dB

AC CHARACTERISTICS (AV = +10, RF = 383Ω)

Slew Rate Note 8 B 25 350 475 - V/µs

Full Power Bandwidth Note 9 B 25 28 38 - MHz

Rise Time Note 10 B 25 - 8 - ns

Fall Time Note 10 B 25 - 9 - ns

Propagation Delay Note 10 B 25 - 9 - ns

Overshoot B 25 - 1.8 - %

-3dB Bandwidth VOUT = 100mV B 25 - 65 - MHz

Settling Time to 1% 2V Output Step B 25 - 75 - ns

Settling Time to 0.1% 2V Output Step B 25 - 130 - ns

VIDEO CHARACTERISTICS

Differential Gain (Note 15) RL = 150ΩB 25 - 0.03 - %

Differential Phase (Note 15) RL = 150ΩB 25 - 0.03 - Degrees

NOTES:

5. VCM = ±2.5V. At -40oC Product is tested at VCM = ±2.25V because short test duration does not allow self heating.

6. RL= 100Ω,V

IN = 2.5V. This is the minimum current which must be pulled out of the Disable pin in order to disable the output. The output is

considered disabled when -10mV ≤ VOUT ≤ +10mV.

7. VIN = 0V. This is the maximum current that can be pulled out of the Disable pin with the HA5022 remaining enabled. The HA5022 is

considered disabled when the supply current has decreased by at least 0.5mA.

8. VOUT switches from -2V to +2V, or from +2V to -2V. Specification is from the 25% to 75% points.

9. .

10. RL= 100Ω,V

OUT = 1V. Measured from 10% to 90% points for rise/fall times; from 50% points of input and output for propagation delay.

11. A. Production Tested; B. Typical or Guaranteed Limit based on characterization; C. Design Typical for information only.

12. VIN = +2V, DISABLE = +5V to 0V. Measured from the 50% point of DISABLE to VOUT = 0V.

13. VIN = +2V, DISABLE = 0V to +5V. Measured from the 50% point of DISABLE to VOUT = 2V.

14. VIN = 0V, Force VOUT from 0V to ±2.5V, tR = tF = 50ns, DISABLE = 0V.

15. Measured with a VM700A video tester using an NTC-7 composite VITS.

16. VOUT =±2.5V. At -40oC Product is tested at VOUT = ±2.25V because short test duration does not allow self heating.

Electrical Speciﬁcations VSUPPLY = ±5V, RF = 1kΩ, AV = +1, RL = 400Ω, CL≤10pF, Unless Otherwise Specified (Continued)

PARAMETER TEST

CONDITIONS

(NO TE 11)

TEST

LEVEL TEMP.

(oC) MIN TYP MAX UNITS

FPBW Slew Rate

2πVPEAK

-----------------------------;V

PEAK 2

HA5022

Test Circuits and Waveforms

FIGURE 1. TEST CIRCUIT FOR TRANSIMPEDANCE MEASUREMENTS

FIGURE 2. SMALL SIGNAL PULSE RESPONSE CIRCUIT FIGURE 3. LARGE SIGNAL PULSE RESPONSE CIRCUIT

NOTE:

17. A series input resistor of ≥100Ω is recommended to limit input currents in case input signals are present before the HA5022 is powered up.

FIGURE 4. SMALL SIGNAL RESPONSE FIGURE 5. LARGE SIGNAL RESPONSE

50Ω

DUT

HP4195

NETWORK

ANALYZER

VIN VOUT

RF, 1kΩ

100Ω

50Ω

-DUT

100Ω

(NOTE 17) VIN VOUT

RF, 681Ω400Ω

50Ω

-DUT

681Ω

100Ω

(NOTE 17)

Vertical Scale: VIN = 100mV/Div., VOUT = 100mV/Div.

Horizontal Scale: 20ns/Div. Vertical Scale: VIN = 1V/Div., VOUT = 1V/Div.

Horizontal Scale: 50ns/Div.

HA5022

Schematic Diagram

(One Ampliﬁer of Two)

800 R5

2.5K R6

15K D2

QP2

60K

QN1

QN2

QN3

QN4

800

15K

DIS

QN7

820

QP4

QN6

QP3

1.25K

QN5

+IN

QP7

R13

R12

280

QP6

QN8

QP5

R10

820

QN9 QN11

QN10

QP10

QP8 QP9

R11

R14

280 QN14

R16

400

R22

280

QN16

R17

280 R18

280

QP11

R15

400 R19

400

QP14

QN12

QP12

-IN

QN13

QP13 C2

R23

400 R26

200

R24

140

R20

140

QP15

QN17

R25

QN18

R25

140

R21

140

R26

200

QP16

R27

200

R33

QP18

QN20

QP17

R28

QN15

R30

QN19

OUT

QN21

R32

R29

9.5

QP19

QP20

R31

V+

V-

QP1

R33

800

1.4pF

HA5022

Application Information

Optimum Feedback Resistor

The plots of inverting and non-inverting frequency response,

see Figure 11 and Figure 12 in the Typical Performance

Curves section, illustrate the performance of the HA5022 in

various closed loop gain conﬁgurations. Although the

bandwidth dependency on closed loop gain isn’t as severe

as that of a voltage feedback ampliﬁer, there can be an

appreciable decrease in bandwidth at higher gains. This

decrease may be minimized by taking advantage of the

current feedback ampliﬁer’s unique relationship between

bandwidth and RF. All current feedback ampliﬁers require a

feedback resistor, even for unity gain applications, and RF,in

conjunction with the internal compensation capacitor, sets

the dominant pole of the frequency response. Thus, the

ampliﬁer’s bandwidth is inversely proportional to RF. The

HA5022 design is optimized for a 1000Ω RF at a gain of +1.

Decreasing RFin a unity gain application decreases stability,

resulting in excessive peaking and overshoot. At higher

gains the ampliﬁer is more stable, so RF can be decreased

in a trade-off of stability for bandwidth.

The table below lists recommended RF values for various

gains, and the expected bandwidth.

PC Board Layout

The frequency response of this ampliﬁer depends greatly on

the amount of care taken in designing the PC board. The

use of low inductance components such as chip resistors

and chip capacitors is strongly recommended. If leaded

components are used the leads must be kept short

especially for the power supply decoupling components and

those components connected to the inverting input.

Attention must be given to decoupling the power supplies. A

large value (10µF) tantalum or electrolytic capacitor in

parallel with a small value (0.1µF) chip capacitor works well

in most cases.

A ground plane is strongly recommended to control noise.

Care must also be taken to minimize the capacitance to

ground seen by the ampliﬁer’s inverting input (-IN). The

larger this capacitance, the worse the gain peaking, resulting

in pulse overshoot and possible instability. It is

recommended that the ground plane be removed under

traces connected to -IN, and that connections to -IN be kept

as short as possible to minimize the capacitance from this

node to ground.

Driving Capacitive Loads

Capacitive loads will degrade the ampliﬁer’s phase margin

resulting in frequency response peaking and possible

oscillations. In most cases the oscillation can be avoided by

placing an isolation resistor (R) in series with the output as

shown in Figure 6.

The selection criteria for the isolation resistor is highly

dependent on the load, but 27Ω has been determined to be

a good starting value.

Power Dissipation Considerations

Due to the high supply current inherent in dual ampliﬁers,

care must be taken to insure that the maximum junction

temperature (TJ, see Absolute Maximum Ratings) is not

exceeded. Figure 7 shows the maximum ambient

temperature versus supply voltage for the available package

styles (PDIP, SOIC). At VS = ±5V quiescent operation both

package styles may be operated over thefull industrial range

of -40oC to 85oC. It is recommended that thermal

calculations, which take into account output power, be

performed by the designer.

Enable/Disable Function

When enabled the ampliﬁer functions as a normal current

feedback ampliﬁer with all of the data in the electrical

speciﬁcations table being valid and applicable. When

GAIN

(ACL)R

F (Ω)BANDWIDTH

(MHz)

-1 750 100

+1 1000 125

+2 681 95

+5 1000 52

+10 383 65

-10 750 22

VIN VOUT

FIGURE 6. PLACEMENT OF THE OUTPUT ISOLATION

RESISTOR, R

100Ω

140

130

120

110

100

80 5 7 9 111315

MAX. AMBIENT TEMPERATURE

SUPPLY VOLTAGE (±V)

PDIP

SOIC

FIGURE 7. MAXIMUM OPERATING AMBIENT

TEMPERATURE vs SUPPLY VOLTAGE

HA5022

disabled the ampliﬁer output assumes a true high

impedance state and the supply current is reduced

signiﬁcantly.

The circuit shown in Figure 8 is a simpliﬁed schematic of the

enable/disable function. The large value resistors in series

with the DISABLE pin makes it appear as a current source to

the driver. When the driver pulls this pin low current ﬂows out

of the pin and into the driver. This current, which may be as

large as 350µA when external circuit and process variables

are at their extremes, is required to insure that point “A”

achieves the proper potential to disable the output. The

driver must have the compliance and capability of sinking all

of this current.

When VCC is +5V the DISABLE pin may be driven with a

dedicated TTL gate. The maximum low level output voltage

of the TTL gate, 0.4V, has enough compliance to insure that

the ampliﬁer will always be disabled even though D1 will not

turn on, and the TTL gate will sink enough current to keep

point “A” at its proper voltage. When VCC is greater than +5V

the DISABLE pin should be driven with an open collector

device that has a breakdown rating greater than VCC.

Referring to Figure 8, it can be seen that R6will act as a pull-

up resistor to +VCC if the DISABLE pin is left open. In those

cases where the enable/disable function is not required on

all circuits some circuits can be permanently enabled by

letting the DISABLE pin ﬂoat. If a driver is used to set the

enable/disable level, be sure that the driver does not sink

more than 20µA when the DISABLE pin is at a high level.

TTL gates, especially CMOS versions, do not violate this

criteria so it is permissible to control the enable/disable

function with TTL.

Typical Applications

Two Channel Video Multiplexer

Referring to the ampliﬁer U1A in Figure 9, R1terminates the

cable in its characteristic impedance of 75Ω, and R4 back

terminates the cable in its characteristic impedance. The

ampliﬁer is set up in a gain conﬁguration of +2 to yield an

overall network gain of +1 when driving a double terminated

cable. The value of R3can be changed if a different network

gain is desired. R5 holds the disable pin at ground thus

inhibiting the ampliﬁer until the switch, S1, is thrown to

position 1. At position 1 the switch pulls the disable pin up to

the plus supply rail thereby enabling the ampliﬁer. Since all

of the actual signal switching takes place within the ampliﬁer,

it’s differential gain and phase parameters, which are 0.03%

and 0.03 degrees respectively, determine the circuit’s

performance. The other circuit, U1B, operates in a similar

manner.

When the plus supply rail is 5V the disable pin can be driven

by a dedicated TTL gate as discussed earlier. If a multiplexer

IC or its equivalent is used to select channels its logic must

be break before make. When these conditions are satisﬁed

the HA5022 is often used as a remote video multiplexer, and

the multiplexer may be extended by adding more ampliﬁer

ICs.

Low Impedance Multiplexer

Two common problems surface when you try to multiplex

multiple high speed signals into a low impedance source

such as an A/D converter. The ﬁrst problem is the low source

impedance which tends to make ampliﬁers oscillate and

causes gain errors. The second problem is the multiplexer

which supplies no gain, introduces all kinds of distortion and

limits the frequency response. Using op amps which have an

enable/disable function, such as the HA5022, eliminates the

multiplexer problems because the external mux chip is not

needed, and the HA5022 can drive low impedance (large

capacitance) loads if a series isolation resistor is used.

Referring to Figure 10, both inputs are terminated in their

characteristic impedance; 75Ω is typical for video

applications. Since the drivers usually are terminated in their

characteristic impedance the input gain is 0.5, thus the

ampliﬁers, U2, are conﬁgured in a gain of +2 to set the circuit

gain equal to one. Resistors R2 and R3 determine the

ampliﬁer gain, and if a different gain is desired R2should be

changed according to the equation G = (1 + R3/R2). R3sets

the frequency response of the ampliﬁer so you should refer

to the manufacturers data sheet before changing its value.

R5, C1 and D1 are an asymmetrical charge/discharge time

circuit which conﬁgures U1as a break before make switch to

prevent both ampliﬁers from being active simultaneously. If

this design is extended to more channels the drive logic

must be designed to be break before make. R4 is enclosed

in the feedback loop of the ampliﬁer so that the large open

loop ampliﬁer gain of U2 will present the load with a small

closed loop output impedance while keeping the ampliﬁer

stable for all values of load capacitance.

The circuit shown in Figure 10 was tested for the full range of

capacitor values with no oscillations being observed; thus,

problem one has been solved.The frequency and gain

characteristics of the circuit are now those of the ampliﬁer

independent of any multiplexing action; thus, problem two

has been solved. The multiplexer transition time is

approximately 15µs with the component values shown.

15K

V+

ENABLE/DISABLE INPUT

QP3

QP18

R33

R10

FIGURE 8. SIMPLIFIED SCHEMATIC OF ENABLE/DISABLE

FUNCTION

HA5022

NOTES:

18. U1 is HA5022.

19. All resistors in Ω.

20. S1 is break before make.

21. Use ground plane. FIGURE 9. TWO CHANNEL HIGH IMPEDANCE MULTIPLEXER

NOTES:

22. U2: HA5022.

23. U1: CD4011. FIGURE 10. LOW IMPEDANCE MULTIPLEXER

VIDEO INPUT #1

VIDEO INPUT #2

681

2000

U1A

U1B

R10

2000R7

681

+5V IN +5V

0.1µF10µF

-5V IN -5V

0.1µF10µF

R11

100

VIDEO OUTPUT

TO 75Ω LOAD

+5V

ALL

OFF

100Ω

(NOTE 17)

100Ω

(NOTE 17)

INPUT B

-5V

+5V

INHIBIT

CHANNEL

SWITCH

INPUT A

R1A

R1B

D1A

1N4148

U1C

U1A U1B U1D

100K

R5A

2000

C1A

0.047µF

R5B

2000

D1B

1N4148

R1A

681

234

R3A

681

R4A

0.01µF

R2B

681 R4B

R3B

681

0.01µF

OUTPUT

6513

U2B

U2A

C1B

0.047µF

100Ω

(NOTE 17)

100Ω

(NOTE 17)

HA5022

Typical Perf ormance Curves

VSUPPLY = ±5V, A V = +1, RF = 1kΩ, RL = 400Ω, TA = 25oC, Unless Otherwise Specified

FIGURE 11. NON-INVERTING FREQUENCY RESPONSE FIGURE 12. INVERTING FREQUENCY RESPONSE

FIGURE 13. PHASE RESPONSE AS A FUNCTION OF

FREQUENCY FIGURE 14. BANDWIDTH AND GAIN PEAKING vs FEEDBACK

RESISTANCE

FIGURE 15. BANDWIDTH AND GAIN PEAKING vs FEEDBACK

RESISTANCE FIGURE 16. BANDWIDTH AND GAIN PEAKING vs LOAD

RESISTANCE

-1

-2

-3

-4

-5

NORMALIZED GAIN (dB)

FREQUENCY (MHz)

2 10 100 200

VOUT = 0.2VP-P

CL = 10pF AV = +1, RF = 1kΩ

AV = 2, RF = 681Ω

AV = 5, RF = 1kΩ

AV = 10, RF = 383Ω

-1

-2

-3

-4

-5 2 10 100 200

FREQUENCY (MHz)

NORMALIZED GAIN (dB)

VOUT = 0.2VP-P

CL = 10pF

RF = 750Ω

AV = -1

AV = -2

AV = -10

AV = -5

FREQUENCY (MHz)

2 10 100 200

-45

-90

-135

-100

-225

-270

-315

-360

180

135

-45

-90

-135

-180

NONINVERTING PHASE (DEGREES)

INVERTING PHASE (DEGREES)

VOUT = 0.2VP-P

CL = 10pF

AV = +10, RF = 383Ω

AV = -10, RF = 750Ω

AV = -1, RF = 750Ω

AV = +1, RF = 1kΩ

FEEDBACK RESISTOR (Ω)

500 700 900 1100 1300 1500

140

130

120 10

-3dB BANDWIDTH (MHz)

GAIN PEAKING (dB)

VOUT = 0.2VP-P

CL = 10pF

-3dB BANDWIDTH

GAIN PEAKING

AV = +1

FEEDBACK RESISTOR (Ω)

-3dB BANDWIDTH (MHz)

GAIN PEAKING (dB)

100

350 500 650 800 950 1100

-3dB BANDWIDTH

GAIN PEAKING

VOUT = 0.2VP-P

CL = 10pF

AV = +2

LOAD RESISTOR (Ω)

-3dB BANDWIDTH (MHz)

GAIN PEAKING (dB)

130

120

110

100

800 200 400 600 800 1000

VOUT = 0.2VP-P

CL = 10pF

-3dB BANDWIDTH

GAIN PEAKING

AV = +1

HA5022

FIGURE 17. BANDWIDTH vs FEEDBACK RESISTANCE FIGURE 18. SMALL SIGNAL OVERSHOOT vs LOAD

RESISTANCE

FIGURE 19. DIFFERENTIAL GAIN vs SUPPLY VOLTAGE FIGURE 20. DIFFERENTIAL PHASE vs SUPPLY VOLTAGE

FIGURE 21. DISTORTION vs FREQUENCY FIGURE 22. REJECTION RATIOS vs FREQUENCY

Typical Perf ormance Curves

VSUPPLY = ±5V, A V = +1, RF = 1kΩ, RL = 400Ω, TA = 25oC, Unless Otherwise Specified (Continued)

0200 350 500 650 800 950

-3dB BANDWIDTH (MHz)

FEEDBACK RESISTOR (Ω)

VOUT = 0.2VP-P

CL = 10pF

AV = +10

LOAD RESISTANCE (Ω)

0 200 400 600 800 1000

OVERSHOOT (%)

VOUT = 0.1VP-P

CL = 10pF

VSUPPLY = ±5V, AV = +2

VSUPPLY = ±15V, AV = +1

VSUPPLY = ±5V, AV = +1

VSUPPLY = ±15V, AV = +2

SUPPLY VOLTAGE (±V)

3 5 7 9 11 13 15

0.10

0.08

0.06

0.04

0.02

0.00

DIFFERENTIAL GAIN (%)

FREQUENCY = 3.58MHz

RL = 75Ω

RL = 150Ω

RL = 1kΩ

0.08

0.06

0.04

0.02

0.003 5 7 9 11 13 15

SUPPLY VOLTAGE (±V)

DIFFERENTIAL PHASE (DEGREES)

RL = 1kΩ

RL = 75Ω

RL = 150Ω

FREQUENCY = 3.58MHz

-40

-50

-60

-70

-80

-900.3 1 10

FREQUENCY (MHz)

DISTORTION (dBc)

VOUT = 2.0VP-P

CL = 30pF

HD3

HD2

3RD ORDER IMD

HD2

HD3

FREQUENCY (MHz)

-10

-20

-30

-40

-50

-60

-70

-80

REJECTION RATIO (dB)

0.001 0.01 0.1 1 10 30

AV = +1

CMRR

POSITIVE PSRR

NEGATIVE PSRR

HA5022

FIGURE 23. PROPAGATION DELAY vs TEMPERATURE FIGURE 24. PROPAGATION DELAY vs SUPPLY VOLTAGE

FIGURE 25. SLEW RATE vs TEMPERATURE FIGURE 26. NON-INVERTING GAIN FLATNESS vs FREQUENCY

FIGURE 27. INVERTING GAIN FLATNESS vs FREQUENCY FIGURE 28. INPUT NOISE CHARACTERISTICS

Typical Perf ormance Curves

VSUPPLY = ±5V, A V = +1, RF = 1kΩ, RL = 400Ω, TA = 25oC, Unless Otherwise Specified (Continued)

TEMPERATURE (oC)

-50 -25 0 25 50 75 100 125

8.0

7.5

7.0

6.5

6.0

PROPAGATION DELAY (ns)

RL = 100Ω

VOUT = 1.0VP-P

AV = +1

SUPPLY VOLTAGE (±V)

PROPAGATION DELAY (ns)

43 5 7 9 11 13 15

RLOAD = 100Ω

VOUT = 1.0VP-P

AV = +10, RF = 383Ω

AV = +2, RF = 681Ω

AV = +1, RF =1kΩ

TEMPERATURE (oC)

-50 -25 0 25 50 75 100 125

500

450

400

350

300

250

200

150

100

SLEW RATE (V/µs)

VOUT = 2VP-P

+ SLEW RATE

- SLEW RATE

FREQUENCY (MHz)

51015202530

0.8

0.6

0.4

0.2

-0.2

-0.4

-0.6

-0.8

-1.0

-1.2

NORMALIZED GAIN (dB)

VOUT = 0.2VP-P

CL = 10pF

AV= +2, RF = 681Ω

AV= +5, RF = 1kΩ

AV = +1, RF = 1kΩ

AV = +10, RF = 383Ω

0.8

0.6

0.4

0.2

-0.2

-0.4

-0.6

-0.8

-1.0

-1.2

NORMALIZED GAIN (dB)

FREQUENCY (MHz)

51015202530

VOUT = 0.2VP-P

CL = 10pF

AV = -1

AV = -2

AV = -5

AV = -10

RF = 750Ω

FREQUENCY (kHz)

0.01 0.1 1 10 100

VOLTAGE NOISE (nV/√Hz)

CURRENT NOISE (pA/√Hz)

100

1000

800

600

400

200

AV = +10, RF = 383Ω

-INPUT NOISE CURRENT

+INPUT NOISE CURRENT

INPUT NOISE VOLTAGE

HA5022

FIGURE 29. INPUT OFFSET VOLTAGE vs TEMPERATURE FIGURE 30. +INPUT BIAS CURRENT vs TEMPERATURE

FIGURE 31. -INPUT BIAS CURRENT vs TEMPERATURE FIGURE 32. TRANSIMPEDANCE vs TEMPERATURE

FIGURE 33. SUPPLY CURRENT vs SUPPLY VOLTAGE FIGURE 34. REJECTION RATIO vs TEMPERATURE

Typical Perf ormance Curves

VSUPPLY = ±5V, A V = +1, RF = 1kΩ, RL = 400Ω, TA = 25oC, Unless Otherwise Specified (Continued)

1.5

1.0

0.5

0.0-60 -40 -20 0 40 60 80 100 120 14020

VIO (mV)

TEMPERATURE (oC)

-2

-4-60 -40 -20 0 40 60 80 100 120 14020

BIAS CURRENT (µA)

TEMPERATURE (oC)

-60 -40 -20 0 40 60 80 100 120 14020

TEMPERATURE (oC)

BIAS CURRENT (µA)

TEMPERATURE (oC)

4000

3000

2000

1000

TRANSIMPEDANCE (kΩ)

-60 -40 -20 0 40 60 80 100 120 14020

34 5 6 7 8 9 10 11 12 13 14 15

ICC (mA)

SUPPLY VOLTAGE (±V)

125oC

55oC

25oC

-100 -50 0 50 100 150

+PSRR

-PSRR

CMRR

200 250

TEMPERATURE (oC)

REJECTION RATIO (dB)

HA5022

FIGURE 35. SUPPLY CURRENT vs DISABLE INPUT VOLTAGE FIGURE 36. OUTPUT SWING vs TEMPERATURE

FIGURE 37. OUTPUT SWING vs LOAD RESISTANCE FIGURE 38. INPUT OFFSET VOLTAGE CHANGE BETWEEN

CHANNELS vs TEMPERATURE

FIGURE 39. INPUT BIAS CURRENT CHANGE BETWEEN

CHANNELS vs TEMPERATURE FIGURE 40. DISABLE SUPPLY CURRENT vs SUPPLY VOLTAGE

Typical Perf ormance Curves

VSUPPLY = ±5V, A V = +1, RF = 1kΩ, RL = 400Ω, TA = 25oC, Unless Otherwise Specified (Continued)

10 2 3 4 5 6 7 8 9 10 11 12 13 14 15

DISABLE INPUT VOLTAGE (V)

SUPPLY CURRENT (mA)

+5V +10V +15V

4.0

3.8

3.6-60 -40 -20 0 40 60 80 100 120 14020

TEMPERATURE (oC)

OUTPUT SWING (V)

0.01 0.10 1.00 10.00

VOUT (VP-P)

LOAD RESISTANCE (kΩ)

VS = ±15V

VS = ±10V

VS = ±4.5V

-60 -40 -20 0 40 60 80 100 120 14020

1.2

1.1

1.0

0.9

0.8

VIO (mV)

TEMPERATURE (oC)

-60 -40 -20

1.5

1.0

0.5

0.0

TEMPERATURE (oC)

∆BIAS CURRENT (µA)

40 60 80 100 120 14020

03456789101112131415

SUPPLY VOLTAGE (±V)

ICC (mA)

-55oC

25oC

125oC

HA5022

FIGURE 41. CHANNEL SEPARATION vs FREQUENCY FIGURE 42. ENABLE/DISABLE TIME vs OUTPUT VOLTAGE

FIGURE 43. DISABLE FEEDTHROUGH vs FREQUENCY FIGURE 44. TRANSIMPEDANCE vs FREQUENCY

FIGURE 45. TRANSIMPEDENCE vs FREQUENCY

Typical Perf ormance Curves

VSUPPLY = ±5V, A V = +1, RF = 1kΩ, RL = 400Ω, TA = 25oC, Unless Otherwise Specified (Continued)

-30

-40

-50

-60

-70

-800.1 1 10 30

SEPARATION (dB)

FREQUENCY (MHz)

AV = +1

VOUT = 2VP-P

DISABLE

ENABLE

DISABLE

ENABLE TIME (ns)

OUTPUT VOLTAGE (V)

-2.5 -2.0 -1.5 -1.0 -0.5 0 0.5 1.0 1.5 2.0 2.5

DISABLE TIME (µs)

-20

-40

-50

-60

-70

-80

0.1 1 10 20

FEEDTHROUGH (dB)

FREQUENCY (MHz)

-30

-10

0DISABLE = 0V

VIN = 5VP-P

RF = 750Ω

-135

-90

-45

135

180

0.1

0.01

0.001

0.001 0.01 0.1 1 10 100

PHASE ANGLE (DEGREES)

TRANSIMPEDANCE (MΩ)

RL = 100Ω

FREQUENCY (MHz)

-135

-90

-45

135

180

0.1

0.01

0.001

0.001 0.01 0.1 1 10 100

PHASE ANGLE (DEGREES)

RL = 400Ω

FREQUENCY (MHz)

TRANSIMPEDANCE (MΩ)

HA5022

All Intersil semiconductor products are manufactured, assembled and tested under ISO9000 quality systems certiﬁcation.

Intersil semiconductor products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design and/or specifications at any time with-

out notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and

reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result

from its use. No license is gr anted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.

For information regarding Intersil Corporation and its products, see web site http://www.intersil.com

Die Characteristics

DIE DIMENSIONS:

1650µm x 2540µm x 483µm

METALLIZATION:

Type: Metal 1: AlCu (1%)

Thickness: Metal 1: 8kÅ±0.4kÅ

Type: Metal 2: AlCu (1%)

Thickness: Metal 2: 16kÅ±0.8kÅ

SUBSTRATE POTENTIAL (POWERED UP):

V-

PASSIVATION:

Type: Nitride

Thickness: 4kÅ±0.4kÅ

TRANSISTOR COUNT:

124

PROCESS:

High Frequency Bipolar Dielectric Isolation

Metallization Mask Layout

HA5022

-IN1

V+

OUT1

+IN2

DIS2

V-

OUT2

-IN2

DIS1

+IN1

HA5022