ADS8354IPWR - TEXAS INSTRUMENTS - Datasheet.Directory

1/31

STE100P

February 2006

1 DESCRIPTION

The STE100P, also referred to as STEPHY1, is a

high performance Fast Ethernet physical layer in-

terface for 10Base-T and 100Base-TX applica-

tions.

It was designed with advanced CMOS technology

to provide a Media Independent Interface (MII) for

easy attachment to 10/100 Media Access Control-

lers (MAC) and a physical media interface for

100Base-TX of IEEE802.3u and 10Base-T of

IEEE802.3.

The STEPHY1 supports both half-duplex and full-

duplex operation, at 10 and 100 Mbps operation.

Its operating mode can be set using auto-negotia-

tion, parallel detection or manual control. It also al-

lows for the support of auto-negotiation functions

for speed and duplex detection.

2FEATURES

2.1 Industry standard

■IEEE802.3u 100Base-TX and IEEE802.3

10Base-T compliant

■Support for IEEE802.3x flow control

■IEEE802.3u Auto-Negotiation support for

10Base-T and 100Base-TX

■MII interface

■Standard CSMA/CD or full duplex operation

supported

■Industrial temperature compliant

10/100 FAST ETHERNET 3.3V TRANSCEIVER

Figure 2. Block Diagram

NRZ To Manchester

Encoder

MII

Interface / Controller

10 TX

Filter

TRANSMITTER

10/100

Scrambler

Auto

Negotiation

4B/5B

NRZ To NRZI

Encoder

Link Pulse

Generator

Binary To MLT3

Encoder

RECEIVER

10/100

Parallel to

Serial

Descrambler

Code Align

4B/5B

NRZI To NRZ

Decoder

Serial to

Parallel

NRZ To Manchester

Encoder

Link Pulse

Detector

SMART

Squelch

10 TX Filter

Clock Recovery

Clock

Generation

System

Clock

Adaptive

Equalization

BaseLine

Wander

Binary To MLT3

Decoder

Clock Recovery

REGISTERS

HW Config

Power Down

LEDS

RX Channel

TX Channel

TXP

TXN

RXP

RXN

MDC

MDIO

RXD[3:0]

RX_ER

RX_DV

RX_CLK

TX_CLK

TXD[3:0]

TX_ER

TX_EN

LEDS

configuration

pins

Serial Management

10Mb/s

100Mb/s

10Mb/s

Loopback

Rev. 19

gure 1.

age

Table 1. Order Codes

(*) ECOPACK® (see

Section 9

)

Part Number Package

STE100P TQFP64

E-STE100P

(*)

TQFP64

TQFP64 (10x10x1.40mm)

STE100P

2/31

2.2 Physical Layer

■Integrates the whole Physical layer functions of 100Base-TX and 10Base-T

■Provides Full-duplex operation on both 100Mbps and 10Mbps modes

■Provides Auto-negotiation(NWAY) function of full/half duplex operation for both 10 and 100 Mbps

■Provides MLT-3 transceiver with DC restoration for Base-line wander compensation

■Provides transmit wave-shaper, receive filters, and adaptive equalizer

■Provides loop-back modes for diagnostic

■Builds in Stream Cipher Scrambler/ De-scrambler and 4B/5B encoder/decoder

■Supports external transmit transformer with turn ratio 1:1

■Supports external receive transformer with turn ratio 1:1

2.3 LED Display

The LED display, consists of five LEDs having the following characteristics:

■10 Mbps Speed LED: 10Mbps(on) or 100Mbps(off)

■100 Mbps Speed LED: 100Mbps(on) or 10Mbps(off)

■TX/RX Activity LED: Blinks at 10Hz when receiving, but not colliding

■Link LED: On when a good link is detected, blinks when there is TX or RX activity

■Full Duplex / Collision LED: On during Full Duplex operation. Blinks at 20Hz to indicate a collision

2.4 Miscellaneous

■Standard 64-pin QFP package pinout

Figure 3. System Diagram of the STE100P Application

Boot ROM 25 MHz

Crystal

RJ-45

STE100P

STEPHY1

Serial

EEPROM

LEDs

PCI Interface

MAC

Device

Transformer

3/31

STE100P

3 PIN ASSIGNMENT DIAGRAM

Figure 4. Pin Connection

4 PIN DESCRIPTION

Table 2. Pin Description

Pin No. Name Type Description

MII Data Interface

txd4

txd3

txd2

txd1

txd0

ITransmit Data. The Media Access Controller (MAC) drives data to the STE100P

using these inputs.

txd4 is monitored only in Symbol (5B) Mode.

These signals must be synchronized to the tx_clk.

54 tx_en I Transmit Enable. The MAC asserts this signal when it drives valid data on the

txd inputs. This signal must be synchronized to the tx_clk.

53 tx_clk I/O Transmit Clock. Normally the STE100P drives tx_clk. Refer to the Clock

Requirements discussion in the Functional Description section.

25 MHz for 100 Mbps operation.

2.5 MHz for 10 Mbps operation.

28 29 30 31 32

59 58 57 56 54

55 53 52 51 50 49

fde

mf0

mf1

mf3

mf4

mf2

gnda

vcca

gnda

vcca

txn

gnda

gnde

pwrdwn

test

reset

rip

col

txd3

txd2

txd1

tx_en

txd0

tx_clk

tx_er/txd4

rx_er/rxd4

gnde/i

rx_clk

rdx3

mdc

mdio

vcce/i

ledr10

gnde/i

rx_dv

rxd0

rxd1

rdx2

vcce/i

D99TL457B

22 23 24 25 26

crs

mdint

vcce/i

cfg1

cfg0

vcca

rxn

rxp

gnda

txp

17 18 19 20 21

ledtr

ledl

leds

test_se

ledc

vcca

iref

gnda

vcca

STE100P

4/31

52 tx_er I Transmit Coding Error. The MAC asserts this input when an error has occurred

in the transmit data stream. When the STE100P is operating at 100 Mbps, the

STE100P responds by sending invalid code symbols on the line. In Symbol (5B)

Mode this pin functions as txd4.

rxd4

rxd3

rxd2

rxd1

rxd0

OReceive Data. The STE100P drives received data on these outputs, synchro-

nous to rx_clk.

rxd4 is driven only in Symbol (5B) Mode.

48 rx_dv O Receive Data Valid. The STE100P asserts This signal when it drives valid data

on rxd. This output is synchronous to rx_clk.

51 rx_er O Receive Error. The STE100P asserts this output when it receives invalid sym-

bols from the network. This signal is synchronous to rx_clk. In Symbol (5B) Mode

this pin functions as rxd4.

49 rx_clk O Receive Clock. This continuous clock provides reference for rxd, rx_dv, and

rx_er signals. Refer to the Clock Requirements discussion in the Functional

Description section.

25 MHz for 100 Mbps operation.

2.5 MHz for 10 Mbps operation.

59 col O Collision Detected. The STE100P asserts this output when detecting a collision.

This output remains High for the duration of the collision. This signal is asynchro-

nous and inactive during full-duplex operation.

60 crs O Carrier Sense. During half-duplex operation (PR0:8=0), the STE100P asserts

this output when either transmit or receive medium is non idle. During full duplex

operation (PR0:8=1), crs is asserted only when the receive medium is non-idle.

MII Control Interface

42 mdc I Management Data Clock. Clock for the mdio serial data channel. Maximum

frequency is 2.5 MHz.

41 mdio I/O Management Data Input/Output, Bi-directional serial data channel for PHY

communication.

61 mdint OD Management Data Interrupt. When any bit in PR18 = 1, an active High output

on this pin indicates status change in the corresponding bits in PR17.

Interrupt is cleared by reading Register PR17. Requires MDC edge to output.

Physical (Twisted Pair) Interface

12 x1 I 25 MHz reference clock input. When an external 25 MHz crystal is used, this pin

will be connected to one terminal of it. If an external 25 MHz clock source of

oscillator is used, then this pin will be the input pin of it.

11 x2 O 25 MHz reference clock output. When an external 25MHz crystal is used, this pin

will be connected to another terminal of if. If an external clock source is used,

then this pin should be left open.

txp

txn

O The differential Transmit outputs of 100Base-TX or 10Base-T, these pins directly

output to the transformer.

rxp

rxn

I The differential Receive inputs of 100Base-TX or 10Base-T, these pins directly

input from the transformer.

Table 2. Pin Description (continued)

Pin No. Name Type Description

5/31

STE100P

15 iref O Reference Resistor connecting pin for reference current, directly connect a 5KΩ ±

1% resistor to Vss.

38 ledr10 I/O LED display for 10Ms/s link status. This pin will be driven on continually when

10Mb/s network operating speed is detected.

The pull-up/pull-down status of this pin is latched into the PR20 bit 7 during

power up/reset.

37 ledtr LED display for Tx/Rx Activity status. This pin will be driven on at a 10 Hz blinking

frequency when either effective receiving or transmitting is detected.

The status of this pin is latched into the PR20 bit 6 during power up/reset.

36 ledl I/O LED display for Link Status. Blinks when there is TX or RX activity. This pin will be

driven on continually when a good Link test is detected.

The status of this pin is latched into the PR20 bit 5 during power up/reset.

35 ledc I/O LED display for Full Duplex or Collision status. This pin will be driven on

continually when a full duplex configuration is detected. This pin will be driven on

at a 20 Hz blinking frequency when a collision status is detected in the half duplex

configuration.

The status of this pin is latched into the PR20 bit 4 during power up/reset.

34 leds I/O LED display for 100Ms/s link status. This pin will be driven on continually when

100Mb/s network operating speed is detected.

The status of this pin is latched into the PR20 bit 3 during power up/reset.

64 cfg0 I Configuration Control 0.

When A/N is enabled, cfg0 determines operating mode advertisement

capabilities in combination with cfg1 when mf0/ PR0:12 =1. (See Table 2)

When A/N is disabled, cfg1 disables mlt3 and directly affects PR19:0

When cfg0 is Low, mlt3 encoder/decoder is enabled and PR19:1 =0.

When cfg0 is High, mlt3 encoder/decoder is bypassed and PR19:1 = 1.

63 cfg1 I Configuration Control 1.

When A/N is enabled, cfg1 determines operating mode advertisement

capabilities in combination with cfg1 when mf0/ PR0:12 =1. (See Table 2)

When A/N is disabled, CFG1 enables Loopback mode and directly affects PR0

bit 14.

When cfg1 is Low, Loopback mode is disabled and PR0:14 = 0.

When cfg1 is High, Loopback mode is enabled and PR0:14 = 1.

28 reset I Reset (Active-Low). This input must be held low for a minimum of 1 ms to reset

the STE100P. During Power-up, the STE100P will be reset regardless of the state

of this pin, and this reset will not be complete until after >1ms.

29 rip O Reset In Progress. This output is used to indicate when the device has

completed power-up/reset and the registers and functions can be accessed.

When rip is High, power-up/reset has been successful and the device can be

used normally

When rip is Low, device reset is not complete.

8, 30,31,

nc nc (No Connection)

26, 33 test,

test_se

Test pins. Should be tied to ground for normal operation

27 pwrdwn I Power Down. When High, forces STE100P into Power Down mode. This pin is

OR’ed with the Power Down bit (PR0:11). During the Power Down mode, txp/txn

outputs and all LED outputs are 3-stated, and the MII interface is isolated.

Table 2. Pin Description (continued)

Pin No. Name Type Description

STE100P

6/31

mf0

mf1

mf2

mf3

mf4

IMulti-Function pins. Each mf pin internally drives different configuration

functions. The functions of the five mf inputs are as shown in the table below.

The logic level of mf0-4 will determine the value that the affected bits will have

upon reset of the STE100P. The operating functions of cfg0, cfg1, and fde change

depending on the state of mf0 (Auto-Negotiation enabled or disabled). Table 2

shows the relationship between cfg0, cfg1 and fde.

6fde IFull-Duplex Enable.

When A/N is enabled, fde determines full-duplex advertisement capability in

combination with cfg0 and cfg1. (See Table 2)

When A/N is disabled, fde directly affects full-duplex operation and determines

the value of PR0 bit 8 (Full/Half Duplex Mode Select).

When fde is High, full-duplex is enabled and PR0:8 = 1.

When fde is Low, full-duplex is disabled and PR0:8 = 0.

Digital Power Pins

39, 45, 62 vcce, vcce/i

25, 40, 50 gnde, gnde/i

Analog Power Pins

9, 13, 16, 17, 22 vcca

7, 10, 14, 20, 24 gnda

Table 2. Pin Description (continued)

Pin No. Name Type Description

7/31

STE100P

5 HARDWARE CONTROL INTERFACE

5.1 Operating Configurations

The Hardware Control Interface consists of the MF<4:0>, CFG <1:0> and FDE input pins as well as the

LED/PAD pins. This interface is used to configure operating characteristics of the STE100P. The Hard-

ware Control Interface provides initial values for the MDIO registers, and then passes control to the MDIO

Interface. Individual chip addressing via the LED/PAD pins allows multiple STE100P devices to share the

MII interface. Table 3 shows how to set up the desired operating configurations using the Hardware Con-

trol Interface.

Table 3. Operating Configurations / Auto-Negotiation Enabled

Note: If pin 5, MF0 = 0, or ANE (pin MF0 / PR0:12) = 0 (Auto-Negotiation disabled), then PR4 bits 5-8 will contain the default value indicated

in the table describing register PR4.

5.2 LED / PHY Address Interface

The LED output pins can be used to drive LED’s directly, or can be used to provide status information to

a network management device. The active state of each LED output driver is dependent on the logic level

sampled by the corresponding PHY address input upon power-up/reset. For example, if a given PAD input

is resistively pulled low then the corresponding LED output will be configured as an active high driver. Con-

versely, if a given PAD input is resistively pulled high then the corresponding LED output will be configured

as an active low driver. These outputs are standard CMOS drivers and not open-drain.

The STE100P PAD[4:0] inputs provide up to 32 unique PHY address options. An address selection of all

zeros (00000) will result in a PHY isolation condition as a result of power-on/reset, as documented for PR0

bit 10.

(See Section 7 for more detailed descriptions of device operation.)

Desired

Configuration

Input Value PR4 Register Bits Affected

CFG0 CFG1 FDE [8] TXF [7] TXH [6] 10F [5] 10H

Advertise All 1 1 1 1 1 1 1

Advertise 100 HD 1 0 0 0 1 0 0

Advertise 100 HD/FD 1 0 1 1 1 0 0

Advertise 10 HD 0 1 0 0 0 0 1

Advertise 10 HD/FD 0 1 1 0 0 1 1

Advertise 10/100 HD 1 1 0 0 1 0 1

STE100P

8/31

6 REGISTERS AND DESCRIPTORS DESCRIPTION

There are 11 registers with 16 bits each supported for the STE100P. These include 7 basic registers which

are defined according to the clause 22 “Reconciliation Sublayer and Media Independent Interface” and

clause 28 “Physical Layer link signaling for 10 Mb/s and 100 Mb/s Auto-Negotiation on twisted pair” of

IEEE802.3u standard.

In addition, there are 4 special registers for advanced chip control and status information.

6.1 Register List

Table 4. Register List

6.2 Register Descriptions

Address Reg. Index Name Register Descriptions

0 PR0 XCR XCVR Control Register

1 PR1 XSR XCVR Status Register

2 PR2 PID1 PHY Identifier 1

3 PR3 PID2 PHY Identifier 2

4 PR4 ANA Auto-Negotiation Advertisement Register

5 PR5 ANLPA Auto-Negotiation Link Partner Ability Register

6 PR6 ANE Auto-Negotiation Expansion Register

17 PR17 XCIIS XCVR Configuration Information and Interrupt Status Register

18 PR18 XIE XCVR Interrupt Enable Register

19 PR19 100CTR 100Base-TX PHY Control/Status Register

20 PR20 XMC XCVR Mode Control Register

Table 5. Register Descriptions

Bit # Name Descriptions Default Val RW Type

PR0- XCR, XCVR Control Register. The default values on power-up/reset are as listed below.

15 XRST Reset control.

1: Device will be reset. This bit will be cleared by STE100P

itself after the reset is completed.

0R/W

14 XLBEN Loop-back mode select.

1: Loop-back mode is selected.

0: Normal mode

0R/W

13 SPSEL Network Speed select. This bit’s selection will be ignored if

Auto-Negotiation is enabled(bit 12 of PR0 = 1).

1:100Mbps is selected.

0:10Mbps is selected.

1R/W

12 ANEN Auto-Negotiation ability control.

1: Auto-Negotiation function is enabled.

0: Auto-Negotiation is disabled.

1R/W

9/31

STE100P

11 PDEN Power-down mode control.

1: Power-down mode is selected. Setting this bit puts the

STE100P into power-down mode. During the power-down

mode, TXP/TXN and all LED outputs are 3-stated, and the MII

interface is isolated.

0R/W

10 ISOEN 0 – Normal operation.

1 – Isolate PHY from MII.

Setting this control bit isolates the STE100P from the MII, with

the exception of the serial management inter-face. When this

bit is asserted, the STE100Pdoes not respond to TXD[3:0],

TX-EN, and TX-ER inputs, and it presents a high impedance

on its TX-CLK, RX-CLK, RX-DV, RX-ER, D[3:0], COL, and

CRS outputs.

0R/W

9 RSAN Re-Start Auto-Negotiation process control.

1: Auto-Negotiation process will be re-started. This bit will be

cleared by STE100P itself after the Auto-negotiation restarted.

0R/W

8 DPSEL Full/Half duplex mode select.

1: Full duplex mode is selected. This bit will be ignored if Auto-

Negotiation is enabled (bit 12 of PR0 = 1).

0: Half duplex mode is selected

0R/W

7 COLEN Collision test control.

1: Collision test is enabled. 0: normal operation

This bit, when set, causes the COL signal to be asserted as a

result of the assertion of TX _EN. De-assertion of TX_EN will

cause the COL signal to be de-asserted.

0R/W

6~0 --- Reserved 0 RO

R/W = Read/Write able. RO = Read Only.

PR1- XSR, XCVR Status Register. All the bits of this register are read only.

15 T4 100BASE-T4 ability.

Always 0, since STE100P has no T4 ability.

0RO

14 TXFD 100Base-TX full duplex ability.

Always 1, since STE100P has the 100Base-TX full duplex

ability.

1RO

13 TXHD 100Base-TX half duplex ability.

Always 1, since STE100P has the 100Base-TX half duplex

ability.

1RO

12 10FD 10Base-T full duplex ability.

Always 1, since STE100P has 10Base-T full duplex ability.

1RO

11 10HD 10Base-T half duplex ability.

Always 1, since STE100P has 10Base-T half duplex ability.

1RO

10~7 --- Reserved 0 RO

Table 5. Register Descriptions (continued)

Bit # Name Descriptions Default Val RW Type

STE100P

10/31

6MFPS MF Preamble Suppression

1 =Accepts management frames with pre-amble suppressed.

0 = Will not accept management frames with preamble

suppressed. The value of this bit is controlled by bit 1 of PR20.

Its default of 1 indicates that the SFEPHY1 accepts

management frame without preamble. A minimum of 32

preamble bits are required following power-on or hardware

reset. One IDLE bit is required between any two management

transactions as per IEEE 802.3u specification.

1RO

5ANC Auto-Negotiation Completed.

0: Auto-Negotiation process is not completed.

1: Auto-Negotiation process is completed. (PR0, Bit 12 is set)

0RO

4RF Result of remote fault detection.

0: No remote fault condition detected.

1: Remote fault condition detected.

This bit is set when the Link Partner transmits a remote fault

condition (PR5 bit 13 = 1).

0RO/LH*

3AN Auto-Negotiation ability.

Always 1, since STE100P has the Auto-Negotiation ability.

1RO

2LINK Link status.

0: a failure link condition occurred. (Latched until read)

1: a valid link is established.

0 RO/LL*

1JAB Jabber detection.

1: jabber condition is detected (10Base-T only).

0RO/LH*

0EXT Extended register supporting.

Always 1, since STE100P supports extended register

1RO

LL* = Latching Low and clear by read. LH* = Latching High and clear by read.

PR2- PID1, PHY Identifier 1

15~0 PHYID1 Part one of PHY Identifier.

Assigned to the 3rd to 18th bits of the Organizationally Unique

Identifier (OUI). (The ST OUI is 0080E1 hex).

1C04h RO

PR3- PID2, PHY Identifier 2

15~10 PHYID2 Part two of PHY Identifier.

Assigned to the 19th to 24th bits of the Organizationally Unique

Identifier (OUI).

000000b RO

9~4 MODEL Model number of STE100P.

Six bits manufacture’s model number.

000001b RO

3~0 REV Revision number of STE100P.

Four bits manufacture’s revision number.

0001b RO

PR4- ANA, Auto-Negotiation Advertisement

15 NXTPG Next Page ability.

Always 0: since STE100P does not provide next page ability.

0RO

14 --- Reserved

Table 5. Register Descriptions (continued)

Bit # Name Descriptions Default Val RW Type

11/31

STE100P

13 RF Remote Fault function.

1: with remote fault function.

0R/W

12,11 --- Reserved

10 FC Flow Control function Ability.

1:supports PAUSE operation of flow control for full duplex link.

1R/W

9 T4 100BASE-T4 Ability.

Always 0: since STE100P doesn’t have 100BASE-T4 ability.

0RO

8 TXF 100Base-TX Full duplex Ability.

1: with 100Base-TX full duplex ability.

1R/W

7 TXH 100Base-TX Half duplex Ability.

1: with 100Base-TX ability.

1R/W

6 10F 10Base-T Full duplex Ability.

1: with 10Base-T full duplex ability.

1R/W

5 10H 10Base-T Half duplex Ability.

1: with 10Base-T ability.

1R/W

4~0 SF Select field. 00000 RO

PR5- ANLP, Auto-Negotiation Link Partner ability

15 LPNP Link partner Next Page ability.

0: link partner without next page ability.

1: link partner with next page ability.

0RO

14 LPACK Received Link Partner Acknowledge.

0: link code work had not received yet.

1: link partner successfully received STE100P’s Link Code

Word.

0RO

13 LPRF Link Partner’s Remote fault status.

0: no remote fault detected.

1: remote fault detected.

0RO

12,11 --- Reserved 0 RO

10 LPFC Link Partner’s Flow control ability.

0: link partner without PAUSE function ability.

1: link partner with PAUSE function full duplex link ability.

0RO

9 LPT4 Link Partner’s 100BASE-T4 ability.

0: link partner without 100BASE-T4 ability.

1: link partner with 100BASE-T4 ability.

0RO

8 LPTXF Link Partner’s 100Base-TX Full duplex ability.

0: link partner without 100Base-TX full duplex ability.

1: link partner with 100Base-TX full duplex ability.

0RO

7 LPTXH Link Partner’s 100Base-TX Half duplex ability.

0: link partner without 100Base-TX.

1: link partner with 100Base-TX ability.

0RO

6 LP10F Link Partner’s 10Base-T Full Duplex ability.

0: link partner without 10Base-T full duplex ability.

1: link partner with 10Base-T full duplex ability.

0RO

Table 5. Register Descriptions (continued)

Bit # Name Descriptions Default Val RW Type

STE100P

12/31

5 LP10H Link Partner’s 10Base-T Half Duplex ability.

0: link partner without 10Base-T ability.

1: link partner with 10Base-T ability.

0RO

4~0 LPSF Link partner select field. Default 00001=IEEE 802.3. 00001 RO

PR6- ANE, Auto-Negotiation expansion

15~5 --- Reserved 0 RO

4 PDF Parallel detection fault.

0: no fault detected.

1: a fault detected via parallel detection function.

0RO/LH*

3 LPNP Link Partner’s Next Page ability.

0: link partner without next page ability.

1: link partner with next page ability.

0RO

2 NP STE100P’s next Page ability.

Always 0, since STE100P without next page ability.

0RO

1 PR Page Received.

0: no new page has been received.

1: a new page has been received.

0RO/LH*

0 LPAN Link Partner Auto-Negotiation ability.

0: link partner has no Auto-Negotiation ability.

1: link partner has Auto-Negotiation ability.

0RO

LH = High Latching and cleared by reading.

PR17- XCIIS, XCVR Configuration information and Interrupt Status

15~10 ---- Reserved 0 RO

9 SPEED Configured information of Speed.

0: the speed is 10Mb/s.

1: the speed is 100Mb/s.

1RO

8 DUPLEX Configured information of Duplex.

0: the duplex mode is half.

1: the duplex mode is full.

0RO

7 PAUSE Configured information of PAUSE function for flow control.

0: PAUSE function is disabled.

1: PAUSE function is enabled

0RO

6 ANC Interrupt source of Auto-Negotiation Completed.

0: Auto-Negotiation has not completed yet.

1: Auto-Negotiation has completed.

0RO/LH*

5 RFD Interrupt source of Remote Fault Detected.

0: there is no remote fault detected.

1: remote fault is detected.

0RO/LH*

4 LS Interrupt source of Link Fail.

0: link test status is up.

1: link is down.

0RO/LH*

Table 5. Register Descriptions (continued)

Bit # Name Descriptions Default Val RW Type

13/31

STE100P

3 ANAR Interrupt source of Auto-Negotiation Acknowledge Received.

0: there is no link code word received.

1: link code word is receive from link partner.

0RO/LH*

2 PDF Interrupt source of Parallel Detection Fault.

0: there is no parallel detection fault.

1: parallel detection is fault.

0RO/LH*

1 ANPR Interrupt source of Auto-Negotiation Page Received.

0: there is no Auto-Negotiation page received.

1: auto-negotiation page is received.

0RO/LH*

0 REF Interrupt source of Receive Error full.

0: the receive error number is less than 64.

1: 64 error packets are received.

0RO/LH*

LH = High Latching and cleared by reading.

PR18- XIE, XCVR Interrupt Enable Register

15~7 --- Reserved

6 ANCE Auto-Negotiation Completed interrupt Enable.

0: disable Auto-Negotiation completed interrupt.

1: enable Auto-Negotiation complete interrupt.

0R/W

5 RFE Remote Fault detected interrupt Enable.

0: disable remote fault detection interrupt.

1: enable remote fault detection interrupt.

0R/W

4 LDE Link Down interrupt Enable.

0: disable link fail interrupt.

1: enable link fail interrupt.

0R/W

3 ANAE Auto-Negotiation Acknowledge interrupt Enable.

0: disable link partner acknowledge interrupt

1: enable link partner acknowledge interrupt.

0R/W

2 PDFE Parallel Detection Fault interrupt Enable.

0: disable fault parallel detection interrupt.

1: enable fault parallel detection interrupt.

0R/W

1 ANPE Auto-Negotiation Page Received interrupt Enable.

0: disable Auto-Negotiation page received interrupt.

1: enable Auto-Negotiation page received interrupt.

0R/W

0 REFE RX_ERR full interrupt Enable.

0: disable rx_err full interrupt.

1: enable more than 64 time rx_err interrupt,

0R/W

PR19- 100CTR, 100Base-TX Control Register

15,14 --- reserved

13 DISRER Disable the RX_ERR counter.

0: the receive error counter - RX_ERR is enabled.

1: the receive error counter - RX_ERR is disabled.

0R/W

12 ANC Auto-Negotiation completed. This bit is the same as PR1:5.

0: the Auto-Negotiation process has not completed yet.

1: the Auto-Negotiation process has completed.

0RO

Table 5. Register Descriptions (continued)

Bit # Name Descriptions Default Val RW Type

STE100P

14/31

11, 10 --- reserved

9 ENRLB Enable remote loop-back function. 1: enable 0: disable 0 R/W

8 ENDCR Enable DC restoration.

0: disable DC restoration.

1: enable DC restoration.

1R/W

7 ENRZI Enable the conversions between NRZ and NRZI.

0: disable the data conversion between NRZ and NRZI.

1: enable the data conversion of NRZI to NRZ in receiving and

NRZ to NRZI in transmitting.

1R/W

6 EN4B5B Enable 4B/5B encoder and decoder

0: the 4B/5B encoder and decoder are bypassed

1: the 4B/5B encoder and decoder are enabled..

1 R/W

5 ISOTX Transmit Isolation. When 1, isolate from MII and tx+/-. The bit

will be set to one if the PHY address is set to 00000 at power-

up/reset This bit must be 0 for normal operation

0R/W

4~2 CMODE Reporting of current operation mode of transceiver.

000: in auto-negotiation

001: 10Base-T half duplex

010: 100Base-TX half duplex

011: reserved

100: reserved

101: 10Base-T full duplex

110: 100Base-TX full duplex

111: isolation, auto-negotiation disable

000 RO

1 DISMLT Disable MLT3.

0: the MLT3 encoder and decoder are enabled.

1: the MLT3 encoder and decoder are bypassed.

0R/W

0 DISCRM Disable Scramble.

0: the scrambler and de-scrambler is enabled.

1: the scrambler and de-scrambler are disabled.

0R/W

PR20- XMC, XCVR Mode control

15~12 --- Reserved 0 RO

11 LD Long Distance mode of 10Base-T.

0: normal squelch level.

1: reduces 10Base-T squelch level for extended cable length.

As the length of the cable increases, so does the current.

0R/W

10~8 --- Reserved 0 RO

Table 5. Register Descriptions (continued)

Bit # Name Descriptions Default Val RW Type

15/31

STE100P

7 DEVICE OPERATION

The STE100P integrates the IEEE802.3u compliant functions of PCS (Physical Coding Sub-layer), PMA

(Physical Medium Attachment), and PMD(Physical Medium Dependent) for 100Base-TX, and the

IEEE802.3 compliant functions of Manchester encoding/decoding and transceiver for 10Base-T. All the

functions and operation schemes are described in the following sections.

7.1 100Base-TX Transmit Operation

Regarding the 100Base-TX transmission, the device provides the transmission functions of PCS, PMA,

and PMD for encoding of MII data nibbles to five-bit code-groups (4B/5B), scrambling, serialization of

scrambled code-groups, converting the serial NRZ code into NRZI code, converting the NRZI code into

MLT3 code, and then driving the MLT3 code into the category 5 Unshielded Twisted Pair cable through

an isolation transformer with the turns ratio of 1:1.

Data code-groups Encoder:

In normal MII mode application, the device receives nibble type 4B data via

the TxD0~3 inputs of the MII. These inputs are sampled by the device on the rising edge of Tx-clk and

passed to the 4B/5B encoder to generate the 5B code-group used by 100Base-TX.

Idle code-groups:

In order to establish and maintain the clock synchronization, the device needs to keep

transmitting signals to the medium. The device will generate Idle code-groups for transmission when there

is no real data want to be sent by MAC.

Start-of-Stream Delimiter-SSD (/J/K/):

In a transmission stream, the first 16 nibbles are MAC preamble.

In order to let partner delineate the boundary of a data transmission sequence and to authenticate carrier

events, the device will replace the first 2 nibbles of the MAC preamble with /J/K/ code-groups.

End-of-Stream Delimiter-ESD (/T/R/):

order to indicate the termination of the normal data transmis-

sions, the device will insert 2 nibbles of /T/R/ code-group after the last nibble of FCS.

Scrambling:

All the encoded data(including the idle, SSD, and ESD code-groups) is passed to the data

scrambler to reduce the EMI and spread the power spectrum using a 10-bit scrambler seed loaded at the

beginning.

7~3 PAD4:0 PHY Address [4:0]:

The values of the PAD[4:0] pins are latched to this register at

power-up/reset. The first PHY address bit transmitted or

received is the MSB of the address (bit 4). A station

management entity connected to multiple PHY entities must

know the appropriate address of each PHY. A PHY address of

<00000> that is latched in to the part at power-up/reset will

cause the Isolate bit of the PR0 (bit 10, register address 00h)

to be set.

After power up/reset the only way to enable or disable isolate

mode is to set or clear the Isolate bit (bit 10) PR0. After power

up/reset writing <00000> to bits [4:0] of this register will not

cause the part to enter isolate mode.

[00001] Strap,

R/W

2 --- reserved 0 RO

1 MFPSE MF Preamble Suppression Enable

1 = Accept management frames with pre-amble suppressed.

0 = Do not accept management frames with preamble

suppressed.

This bit also controls the value of bit 6 in PR1 (MFPS).

1R/W

0 --- reserved 0 RO

Table 5. Register Descriptions (continued)

Bit # Name Descriptions Default Val RW Type

STE100P

16/31

Data conversion of Parallel to Serial, NRZ to NRZI, NRZI to MLT3:

After scrambled, the transmission

data with 5B type in 25MHz will be converted to serial bit stream in 125MHz by the parallel to serial func-

tion. After serialized, the transmission serial bit stream will be further converted from NRZ to NRZI format.

This NRZI conversion function can be bypassed, if the bit 7 of PR19 register is cleared as 0. After NRZI

converted, the NRZI bit stream is passed through MLT3 encoder to generate the TP-PMD specified MLT3

code. With this MLT3 code, it lowers the frequency and reduces the energy of the transmission signal in

the UTP cable and also makes the system easily to meet the FCC specification of EMI.

Wave-Shaper and Media Signal Driver:

In order to reduce the energy of the harmonic frequency of trans-

mission signals, the device provides the wave-shaper prior to the line driver to smooth but keep symmetric

the rising/falling edge of transmission signals. The wave-shaped signals include the 100Base-TX and

10Base-T both are passed to the same media signal driver. This design can simplify the external magnetic

connection with single one.

7.2 100Base-TX Receive Operation

Regarding the 100Base-TX receiving operation, the device provides the receiving functions of PMD, PMA,

and PCS for receiving incoming data signals through category 5 UTP cable and an isolation transformer

with turns ratio of 1: 1. It includes the adaptive equalizer and baseline wander, data conversions of MLT3

to NRZI, NRZI to NRZ and serial to parallel, the PLL for clock and data recovery, the de-scrambler, and

the decoder of 5B/4B.

Adaptive Equalizer and Baseline Wander:

Since the high speed signals over the unshielded (or shield-

ed) twisted Pair cable will induce the amplitude attenuation and phase shifting. Furthermore, these effects

are depends on the signal frequency, cable type, cable length and the connectors of the cabling. So a re-

liable adaptive equalizer and baseline wander to compensate all the amplitude attenuation and phase shift-

ing are necessary. In the transceiver, it provides the robust circuits to perform these functions.

MLT3 to NRZI Decoder and PLL for Data Recovery:

After receiving the proper MLT3 signals, the device

converts the MLT3 to NRZI code for further processing. After adaptive equalizer, baseline wander, and

MLT3 to NRZI decoder, the compensated signals with NRZI type in 125MHz are passed to the Phase Lock

Loop circuits to extract out the original data and synchronous clock.

Data Conversions of NRZI to NRZ and Serial to Parallel:

After data is recovered, the signals will be

passed to the NRZI to NRZ converter to generate the 125 MHz serial bit stream. This serial bit stream will

be packed to parallel 5B type for further processing. The NRZI to NRZ conversion can be bypassed, if the

bit 7 of PR19 register is cleared as 0.

De-scrambling and Decoding of 5B/4B:

The parallel 5B type data is passed to de-scrambler and 5B/4B

decoder to return their original MII nibble type data.

Carrier sensing:

Carrier Sense(CRS) signal is asserted when the STE100P detects any 2 non-contiguous

zeros within any 10 bit boundary of the receiving bit stream. CRS is de-asserted when ESD code-group or

Idle code-group is detected. In half duplex mode, CRS is asserted during packet transmission or receive.

But in full duplex mode, CRS is asserted only during packet reception.

7.3 10Base-T Transmit Operation

This includes the parallel to serial converter, Manchester Encoder, Link test function, Jabber function and

the transmit wave-shaper and line driver described in the section of “Wave-Shaper and Media Signal Driv-

er” of “100BASE-T Transmission Operation”. It also provides Collision detection and SQE test for half du-

plex application.

7.4 10Base-T Receive Operation

This includes the carrier sense function, receiving filter, PLL for clock and data recovering, Manchester

decoder, and serial to parallel converter.

17/31

STE100P

7.5 Loop-back Operation

The STE100P provides internal loop-back option for both the 100Base-TX and 10Base-T operations. Set-

ting bit 14 of PR0 register to 1 can enable the loop-back option. In this loop-back operation, the txp/txn

and rxp/rxn lines are isolated from the media. The STE100P also provides remote loop-back operation for

100Base-TX operation. Setting bit 9 of PR19 register to 1 enables the remote loop-back operation.

In the 100Base-TX internal loop-back operation, the data comes from the transmit output of NRZ to NRZI

converter then loop-back to the receive path into the input of NRZI to NRZ converter.

In the 100Base-TX remote loop-back operation, the data is received from rxp/rxn pins through receive

path to the output of data and clock recover and then loop-back to the input of NRZI to MLT3 converter of

transmit path then transmit out to the medium via the transmit line drivers.

In the 10Base-T loop-back operation, the data is through transmit path and loop-back from the output of

the Manchester encoder into the input of Phase Lock Loop circuit of receive path.

7.6 Full Duplex and Half Duplex Operation

The STE100P can operate for either full duplex or half duplex network application. In full duplex, both

transmit and receive can be operated simultaneously. Under full duplex mode, collision(COL) signal is ig-

nored and carrier sense(CRS) signal is asserted only when the STE100P is receiving.

In half duplex mode, either transmit or receive can be operated at one time. Under half duplex mode, col-

lision signal is asserted when transmit and receive signals collided and carrier sense asserted during

transmission and reception.

7.7 Auto-Negotiation Operation

The Auto-Negotiation function is designed to provide the means to exchange information between the

STE100P and the network partner to automatically configure both to take maximum advantage of their

abilities, and both are setup accordingly. The Auto-Negotiation function can be controlled through ANE,

bit 12 of the PR0 register, or the MF0 pin 5.

Auto-Negotiation exchanges information with the network partner using the Fast Link Pulses(FLPs) - a

burst of link pulses. There are 16 bits of signaling information contained in the burst pulses to advertise all

remote partner’s capabilities which are determined by the register of PR4. According to this information

they find out their highest common capability by following the priority sequence as below:

1. 100Base-TX full duplex

2. 100Base-TX half duplex

3. 10Base-T full duplex

4. 10Base-T half duplex

During power-up or reset, if Auto-Negotiation is found enabled then FLPs will be transmitted and the Auto-

Negotiation function will proceed. Otherwise, the Auto-Negotiation will not occur until the bit 12 of PR0 reg-

ister is set to 1. When Auto-Negotiation is disabled, then the Network Speed and Duplex Mode are select-

ed by programming PR0 register.

7.8 Power Down Operation

To reduce the power consumption, the STE100P is designed with a power down feature, which can save

the power consumption significantly. Since the power supply of the 100Base-TX and 10Base-T circuits

are separated, the STE100P can turn off the circuit of either the 100Base-TX or 10Base-T when the other

one of them is operating. There is also a Power Down mode which can be selected by PDEN in register

PR0 bit 11. During the Power Down mode, TXP/TXN outputs and all LED outputs are 3-stated, and the

MII interface is isolated. During Power Down mode the MII management interface is still available for read-

ing and writing device registers. Power Down mode can be exited by clearing bit 11 of register PR0 or by

a hardware or software reset (setting PR0:15=1).

STE100P

18/31

7.9 LED Display Operation

The STE100P provides 5 LED pins, the detail descriptions about the operation are described in the PIN

Description section, and as follows.

■Speed LED: 100Mbps(on) or 10Mbps(off)

■Receive LED: Blinks at 10Hz when receiving, but not colliding

■Transmit LED: Blinks at 10Hz when transmitting, but not colliding

■Link LED: On when 100M or 10M link ok

■Collision LED: Blinks at 20Hz to indicate a collision

7.10 Reset Operation

There are two ways to reset the STE100P. First, for hardware reset, the STE100P can be reset via RESET

pin (pin 28). The active low Reset input signal is required at least 1 ms to ensure proper reset operation.

Second, for software reset, when bit 15 of register PR0 is set to 1, the STE100P will reset entire circuits

and registers to their default values, then clear the bit 15 of PR0 to 0, and set the RIP output pin 29 to logic

1. Both hardware and software reset operations initialize all registers to their default values. This process

includes re-evaluation of all hardware-configurable registers. Logic levels on several I/O pins are detected

during hardware reset period to determine the initial functionality of STE100P. Some of these pins are

used as outputs after the reset operation. Care must be taken to ensure that the configuration setup will

not interfere with normal operation. Dedicated configuration pins can be tied to the Vcc or ground directly.

Configuration pins multiplexed with LED outputs should be weakly pulled up or weakly pulled down

through resistors as shown in the following circuits.

Figure 5.

Figure 6.

19/31

STE100P

Note:

The above LED connections are recommended for setting a Logic Level 1 or Logic Level 0 on the

STE100P LED/PHY Address pins, for determining PHY address.

7.11 Preamble Suppression

Preamble suppression mode in the STEPHY1 is indicated by a one in bit six of the PR1 Register. If it is

determined that all PHY devices in the system support preamble suppression, then a preamble is not nec-

essary for each management transaction. The first transaction following power-up/hardware reset re-

quires 32 bits of preamble. The full 32 bit preamble is not required for each additional transaction. The

STEPHY1 will respond to management accesses without preamble, but a minimum of one idle bit between

management transactions is required as specified in IEEE 802.3u.

7.12 Remote Fault

The remote fault function indicates to a link partner that a fault condition has occurred by using the Remote

Fault bit, which is encoded in bit 13 of the Link Code Word. A local device indicates to its link partner that

it has found a fault by setting the Remote Fault bit in the Auto-Negotiation register to logic one and rene-

gotiating with the link partner. The Remote Fault bit remains at logic one until successful negotiation with

the Link Code Word occurs. The bit will then return to 0. When the message is sent that the Remote Fault

bit is set to logic one, the device will set the Remote Fault bit in the MII to logic one if the management

function is present.

7.13 Transmit Isolation

Figure 7.

STA/STE

TxD

RxD

4/5

STEPHY1

ttp

MII

tpn

TX(100MHz)/TP(10MHz)

Ethernet

STE100P

20/31

8 ELECTRICAL SPECIFICATIONS AND TIMINGS

Table 6. Absolute Maximum Ratings

Parameter Value

Supply Voltage(Vcc) -0.5 V to 7.0 V

Input Voltage -0.5 V to VCC + 0.5 V

Output Voltage -0.5 V to VCC + 0.5 V

Storage Temperature -65 °C to 150 °C(-85°F to 302°F)

Ambient Temperature (-40)°C to +85°C)

ESD Protection 2000V

Table 7. General DC Specifications

Symbol Parameter Test Condition Min. Typ. Max. Units

General DC

Vcc Supply Voltage 3.15 3.3 3.45 V

10Base-T Voltage/Current Characteristics

Vida10 Input Differential Accept Peak

Voltage

5MHz ~ 10MHz 585 3100 mV

Vidr10 Input Differential Reject Peak

Voltage

5MHz ~ 10MHz 0 585 mV

Vod10 Output Differential Peak Voltage 2200 2800 mV

Icc10 Supply Current 100% utilization, min. IPG,

Vcc=3.3V, including TX output

driver

90 mA

100Base-TX Voltage/Current Characteristics

Vida100 Input Differential Accept Peak

Voltage

200 1000 mV

Vidr100 Input Differential Reject Peak

Voltage

0 200 mV

Vod100 Output Differential Peak Voltage 950 1050 mV

Icc100 Supply Current 100% utilization, min. IPG,

Vcc=3.3V, including TX output

driver

100 mA

21/31

STE100P

Table 8. AC Specifications

Figure 8. Normal Link Pulse timings

Symbol Parameter Test Condition Min. Typ. Max. Units

X1 Specifications

TX1d X1 Duty Cycle 45 50 55 %

TX1p X1 Period 30 ns

TX1t X1 Tolerance ±50 PPM

TX1CLX1 Load Capacitance 18 pF

10Base-T Normal Link Pulse (NLP) Timings Specifications

TNPW NLP Width 10Mbps 100 ns

TNPC NLP Period 10Mbps 8 24 ms

Table 8. AC Specifications

Symbol Parameter Test Condition Min. Typ. Max. Units

Auto-Negotiation Fast Link Pulse(FLP) Timings Specifications

Tflpw FLP Width 100 ns

Tflcpp Clock pulse to clock pulse period 111 125 139 µs

Tflcpd Clock pulse to Data pulse period 55.5 62.5 69.5 µs

- Number of pulses in one burst 17 33 pulse

Tflbw Burst Width 2 ms

Tflbp FLP Burst period 8 16 24 ms

Tnpw

Tnpc

STE100P

22/31

Figure 9. Fast Link Pulse timing

Table 8. AC Specifications

Symbol Parameter Test Condition Min. Typ. Max. Units

100Base-TX Transmitter AC Timings Specification

Tjit TDP-TDN Differential Output

Peak Jitter

1.4 ps

MII Management Clock Timing Specifications

t1 MDC High Pulse Width 200 — ns

t2 MDC Low Pulse Width 200 — ns

t3 MDC Period 400 — ns

t4 MDIO(I) Setup to MDC Rising

Edge

10 — ns

t5 MDIO(I) Hold Time from MDC

Rising Edge

10 — ns

t6 MDIO(O) Valid from MDC Rising

Edge

0 300 ns

Tflpw

Tflbw Tflbp

Tflcpp

Tflcpd

23/31

STE100P

Figure 10. MII Management Clock Timing

Table 8. AC Specifications

Symbol Parameter Test Condition Min. Typ. Max. Units

MII Receive Timing Specification

t1 RX-ER, RX-DV, RXD[3:0] Setup

to RX-CLK

10 — ns

t2 RX-ER, RX-DV, RXD[3:0] Hold

After RX-CLK

10 — ns

t3 RX-CLK High Pulse Width (100

Mbits/s)

14 26 ns

RX-CLK High Pulse Width (10

Mbits/s)

200 ns

t4 RX-CLK Low Pulse Width (100

Mbits/s)

14 26 ns

RX-CLK Low Pulse Width (10

Mbits/s)

140 260 ns

t5 RX-CLK Period (100 Mbits/s) 40 ns

RX-CLK Period (10 Mbits/s) 400 ns

MDC

MDIO(O)

MDIO(I)

t1 t2 t3

t4 t5

STE100P

24/31

Figure 11. MII Receive Timing

Figure 12. MII Transmit Timing

Table 8. AC Specifications

Symbol Parameter Test Condition Min. Typ. Max. Units

MII Transmit Timing Specification

t1 TX-ER,TX-EN,TXD[3:0] Setup to

TX-CLK Rise

10 — ns

t2 TX-ER,TX-EN,TXD[3:0] Hold

After TX-CLK Rise

025ns

25/31

STE100P

Table 8. AC Specifications

Figure 13. Receive Timing

Symbol Parameter Test Condition Min. Typ. Max. Units

Receive Timing Specification

Rt1 Receive Frame to Sampled Edge

of RX-DV

(100 Mbits/s)

— 300 ns

Receive Frame to Sampled Edge

of RX-DV

(10 Mbits/s)

—4us

Rt2 Receive Frame to CRS High

(100Mbits/s)

— 250 ns

Receive Frame to CRS High (10

Mbits/s)

—3.5us

Rt3 End of Receive Frame to

Sampled Edge of RX-DV (100

Mbits/s)

— 200 ns

End Receive Frame to Sampled

Edge of RX-DV (10 Mbits/s)

—1us

Rt4 End of Receive Frame to CRS

Low (100 Mbits/s)

— 300 ns

End of Receive Frame to CRS

Low (10 Mbits/s)

—1us

STE100P

26/31

Table 8. AC Specifications

Figure 14. Transmit Timing

Symbol Parameter Test Condition Min. Typ. Max. Units

Transmit Timing Specification

t1 TX-EN Sampled to CRS High

(100 Mbits/s)

040ns

TX-EN Sampled to CRS High (10

Mbits/s)

—4us

t2 TX-EN Sampled to CRS Low

(100 Mbits/s)

0 160 ns

TX-EN Sampled to CRS Low (10

Mbits/s)

1us

t3 Transmit Latency (100 Mbits/s) 60 140 ns

Transmit Latency (10 Mbits/s) 400 ns

t4 Sampled TX-EN Inactive to End

of Frame

(100 Mbits/s)

— 170 ns

Sampled TX-EN Inactive to End

of Frame

(10 Mbits/s)

— 500 ns

27/31

STE100P

Figure 15. 100BaseT Transmit Timing

Table 9.

Parameter Sym Min Typ Max Units

TXD, TX_EN, TX_ER Setup to TX_CLK High t2A 10 - - ns

TXD, TX_EN, TX_ER Hold from TX_CLK High t2B 5 - - ns

TX_EN sampled to CRS asserted t2C - 30 40 ns

TX_EN sampled to CRS de-asserted t2D - 40 160 ns

TX_EN sampled to TXP out (Tx latency) t2E 60 100 140 ns

BT is the duration of one bit as transferred to and from the MAC and is the reciprocal of the bit rate.

TXP

STE100P

28/31

Figure 16. 10Base-T Half Duplex Transmit Timing

Table 10.

Parameter Sym Min Typ Max Units

TXD, TX_EN, TX_ER Setup to TX_CLK High t8A 10 - - ns

TXD, TX_EN, TX_ER Hold from TX_CLK High t8B 5 - - ns

TX_EN sampled to CRS asserted t8C - 0 4 us

TX_EN sampled to CRS de-asserted t8E - 1 us

TX_EN sampled to TXP out (Tx latency) t8D - 400 ns

TXP

29/31

STE100P

9 PACKAGE INFORMATION

In order to meet environmental requirements, ST offers these devices in ECOPACK® packages. These

packages have a Lead-free second level interconnect. The category of second Level Interconnect is

marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97.

The maximum ratings related to soldering conditions are also marked on the inner box label.

ECOPACK is an ST trademark. ECOPACK specifications are available at: www.st.com.

Figure 17. TQFP64 (10x10x1.4mm) Mechanical Data & Package Dimensions

OUTLINE AND

MECHANICAL DATA

TQFP64

Seating Plane

0.08mm

DIM.

mm inch

MIN. TYP. MAX. MIN. TYP. MAX.

A 1.60 0.063

A1 0.05 0.15 0.002 0.006

A2 1.35 1.40 1.45 0.053 0.055 0.057

B 0.17 0.22 0.27 0.0066 0.0086 0.0106

C 0.09 0.0035

D 11.80 12.00 12.20 0.464 0.472 0.480

D1 9.80 10.00 10.20 0.386 0.394 0.401

D3 7.50 0.295

e 0.50 0.0197

E 11.80 12.00 12.20 0.464 0.472 0.480

E1 9.80 10.00 10.20 0.386 0.394 0.401

E3 7.50 0.295

L 0.45 0.60 0.75 0.0177 0.0236 0.0295

L1 1.00 0.0393

K 0˚ (min.), 3.5˚ (min.), 7˚(max.)

ccc 0.080 0.0031

TQFP64 (10 x 10 x 1.4mm)

0051434 E

ccc

STE100P

30/31

Table 11. Revision History

Date Revision Description of Changes

January 2004 15 Rev. A12 June 2003 has been migrated from ST-PRESS to EDOCS.

June 2004 16 Changed the Style-sheet on the Rev. A13.

August 2004 17 Wrong package corrected.

September 2004 18 Due to Rev. 17 content was partially wrong. Now fixed.

February 2005 19 Added part number “E-STE100P” (ECOPACK).

Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences

of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted

by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject

to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not

authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics.

The ST logo is a registered trademark of STMicroelectronics.

All other names are the property of their respective owners

STMicroelectronics group of companies

Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan -

Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America

www.st.com

31/31

STE100P