Analog Devices Welcomes Hittite Microwave Corporation NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED www.analog.com www.hittite.com THIS PAGE INTENTIONALLY LEFT BLANK HMC465LP5 / 465LP5E v06.1210 Amplifiers - Driver & Gain Block - SMT 8 GaAs PHEMT MMIC MODULATOR DRIVER AMPLIFIER, DC - 20 GHz Typical Applications Features The HMC465LP5(E) wideband driver is ideal for: Gain: 15 dB * OC192 LN/MZ Modulator Driver Output Voltage to 10Vpk-pk * Microwave Radio & VSAT +24 dBm Saturated Output Power * Test Instrumentation Supply Voltage: +8V @160 mA 50 Ohm Matched Input/Output * Military EW, ECM & C I 3 32 Lead 5x5 mm QFN Package: 25 mm2 Functional Diagram General Description The HMC465LP5(E) is a GaAs MMIC PHEMT Distributed Driver Amplifier packaged in leadless 5x5 mm surface mount package which operate between DC and 20 GHz. The amplifier provides 15 dB of gain, 3 dB noise figure and +25 dBm of saturated output power while requiring only 160 mA from a +8V supply. Gain flatness is excellent at 0.5 dB as well as 4 deg deviation from linear phase from DC - 10 GHz making the HMC465LP5(E) ideal for OC192 fiber optic LN/MZ modulator driver amplifiers as well as test equipment applications. The HMC465LP5(E) amplifiers I/Os are internally matched to 50 Ohms. Electrical Specifications, TA = +25 C, Vdd= 8V, Vgg2= 1.5V, Idd= 160 mA* Parameter Min. Frequency Range Gain Typ. Max. Min. DC - 6 13 0.75 Gain Variation Over Temperature 0.015 Max. Min. 6.0 - 12.0 16 Gain Flatness Typ. 12 15 9.5 0.25 0.02 0.020 Typ. Max. 12.0 - 20.0 GHz 12.5 dB 1.5 0.025 Units 0.035 dB 0.045 dB/ C Noise Figure 3.0 3.0 4.0 dB Input Return Loss 20 15 8 dB Output Return Loss 22 17 12 dB Output Power for 1 dB Compression (P1dB) 20 dBm 25.5 25 23 dBm Output Third Order Intercept (IP3) 32 28 24 dBm Saturated Output Voltage 10 10 8 Vpk-pk Group Delay Variation 15 15 Supply Current (Idd) (Vdd= 8V, Vgg1= -0.6V Typ.) 160 160 Saturated Output Power (Psat) 21 24 20 23 16 pSec 160 mA * Adjust Vgg1 between -2 to 0V to achieve Idd= 160 mA typical. 8-1 For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC465LP5 / 465LP5E GaAs PHEMT MMIC MODULATOR DRIVER AMPLIFIER, DC - 20 GHz Gain & Return Loss Gain vs. Temperature 8 20 20 15 16 5 S21 S11 S22 0 GAIN (dB) RESPONSE (dB) 10 -5 -10 12 +25C +85C -40C 8 -15 4 -20 -25 0 -30 0 2 4 6 8 10 12 14 16 18 20 0 22 2 4 6 FREQUENCY (GHz) Input Return Loss vs. Temperature 12 14 16 18 20 22 0 +25C +85C -40C -5 RETURN LOSS (dB) -5 RETURN LOSS (dB) 10 Output Return Loss vs. Temperature 0 -10 -15 -20 -25 +25C +85C -40C -10 -15 -20 -25 -30 -30 0 2 4 6 8 10 12 14 16 18 20 22 0 2 4 6 FREQUENCY (GHz) 10 12 14 16 18 20 18 20 22 Noise Figure vs. Temperature 25 10 9 15 NOISE FIGURE (dB) 8 5 S21 S11 S22 -5 -15 -25 +25C +85C -40C 7 6 5 4 3 2 -35 -45 0.00001 8 FREQUENCY (GHz) Low Frequency Gain & Return Loss RESPONSE (dB) 8 FREQUENCY (GHz) Amplifiers - Driver & Gain Block - SMT v06.1210 1 0 0.0001 0.001 0.01 0.1 FREQUENCY (GHz) 1 10 0 2 4 6 8 10 12 14 16 22 FREQUENCY (GHz) For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com 8-2 HMC465LP5 / 465LP5E v03.1106 v06.1210 Psat vs. Temperature 30 30 26 26 Psat (dBm) P1dB (dBm) P1dB vs. Temperature 22 18 +25C +85C -40C 14 +25C +85C -40C 18 10 0 2 4 6 8 10 12 14 16 18 20 22 0 2 4 FREQUENCY (GHz) 38 36 IP3 (dBm) 34 32 30 28 26 +25C +85C -40C 20 18 0 2 4 6 8 10 12 14 16 18 20 22 Gain (dB), P1dB (dBm), Psat (dBm), IP3 (dBm) 40 22 14 16 18 20 22 30 28 26 24 22 20 Gain P1dB 18 Psat IP3 16 14 12 10 7.5 8 8.5 Deviation from Linear Phase DEVIATION FROM LINEAR PHASE (deg) -200 -250 -300 -350 2 12 SUPPLY VOLTAGE (V) Group Delay 1 10 32 FREQUENCY (GHz) 0 8 Gain, Power & Output IP3 vs. Supply Voltage @ 10 GHz, Idd = 160mA Output IP3 vs. Temperature 24 6 FREQUENCY (GHz) -400 3 4 5 6 FREQUENCY (GHz) 8-3 22 14 10 GROUP DELAY (pSec) Amplifiers - Driver & Gain Block - SMT 8 GaAs PHEMT MMIC MODULATOR DRIVER AMPLIFIER, DC - 20 GHz 7 8 9 10 10 6 2 -2 -6 -10 0 2 4 6 8 10 FREQUENCY (GHz) For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC465LP5 / 465LP5E GaAs PHEMT MMIC MODULATOR DRIVER AMPLIFIER, DC - 20 GHz Absolute Maximum Ratings Typical Supply Current vs. Vdd Drain Bias Voltage (Vdd) +9 Vdc Vdd (V) Idd (mA) Gate Bias Voltage (Vgg1) -2 to 0 Vdc +7.5 161 +8.0 160 +8.5 159 Gate Bias Current (Igg1) +3.2mA Gate Bias Voltage (Vgg2) (Vdd -8) Vdc to +3 Vdc Gate Bias Current (Igg2) +3.2mA RF Input Power (RFIN)(Vdd = +8 Vdc) +23 dBm Channel Temperature 150 C Continuous Pdiss (T = 85 C) (derate 24 mW/C above 85 C) 1.56 W Thermal Resistance (channel to ground paddle) 41.5 C/W Storage Temperature -65 to +150 C Operating Temperature -40 to +85 C ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS Outline Drawing NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS] 3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE. 4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM. 8 Amplifiers - Driver & Gain Block - SMT v06.1210 PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM. 5. PACKAGE WARP SHALL NOT EXCEED 0.05mm. 6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED LAND PATTERN. Package Information Part Number Package Body Material Lead Finish MSL Rating HMC465LP5 Low Stress Injection Molded Plastic Sn/Pb Solder MSL1 [1] HMC465LP5E RoHS-compliant Low Stress Injection Molded Plastic 100% matte Sn MSL1 [2] Package Marking [3] H465 XXXX H465 XXXX [1] Max peak reflow temperature of 235 C [2] Max peak reflow temperature of 260 C [3] 4-Digit lot number XXXX For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com 8-4 HMC465LP5 / 465LP5E v06.1210 Amplifiers - Driver & Gain Block - SMT 8 GaAs PHEMT MMIC MODULATOR DRIVER AMPLIFIER, DC - 20 GHz Pin Descriptions Function Description 1, 3, 4, 6 - 12, 14, 17, 18, 19, 20, 22 - 28, 31, 32 Pin Number N/C The pins are not connected internally; however, all data shown herein was measured with these pins connected to RF/DC ground externally. 2 Vgg2 Gate Control 2 for amplifier. +1.5V should be applied to Vgg2 for nominal operation. 5 RFIN This pad is DC coupled and matched to 50 Ohms. 13 Vgg1 Gate Control 1 for amplifier. 15 ACG4 Interface Schematic Low frequency termination. Attach bypass capacitor per application circuit herein. 16 ACG3 21 RFOUT & Vdd RF output for amplifier. Connect the DC bias (Vdd) network to provide drain current (Idd). See application circuit herein. 29 ACG2 30 ACG1 Low frequency termination. Attach bypass capacitor per application circuit herein. Ground Paddle GND Ground paddle must be connected to RF/DC ground. Application Circuit NOTE 1: Drain Bias (Vdd) must be applied through a broadband bias tee or external bias network. 8-5 For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC465LP5 / 465LP5E GaAs PHEMT MMIC MODULATOR DRIVER AMPLIFIER, DC - 20 GHz Evaluation PCB List of Materials for Evaluation PCB 108347 Item Description J1 - J2 SRI K Connector J3 - J4 2mm Molex Header C1, C2 100 pF Capacitor, 0402 Pkg. C3 - C6 1000 pF Capacitor, 0603 Pkg. C7 - C9 4.7 F Capacitor, Tantalum U1 HMC465LP5 / HMC465LP5E PCB [2] 109765 Evaluation PCB [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350 8 [1] The circuit board used in the final application should use RF circuit design techniques. Signal lines should have 50 Ohm impedance while the package ground leads and package bottom should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation board should be mounted to an appropriate heat sink. The evaluation circuit board shown is available from Hittite upon request. For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com Amplifiers - Driver & Gain Block - SMT v06.1210 8-6 HMC465LP5 / 465LP5E v06.1210 Amplifiers - Driver & Gain Block - SMT 8 8-7 GaAs PHEMT MMIC MODULATOR DRIVER AMPLIFIER, DC - 20 GHz Device Operation These devices are susceptible to damage from Electrostatic Discharge. Proper precautions should be observed during handling, assembly and test. The input to this device should be AC-coupled. To provide the typical 8Vp-p output voltage swing, a 1.2Vp-p ACcoupled input voltage swing is required. Device Power Up Instructions 1. Ground the device 2. Set Vgg to -2V (no drain current) 3. Set Vctl to +1V (no drain current) 4. Set Vdd to +5V (no drain current) 5. Adjust Vgg for Idd = 140mA * Vgg may be varied between -1V and 0V to provide the desired eye crossing point percentage (i.e. 50% crosspoint) and a limited cross point control capability. * Vdd may be increased to +7V if required to achieve greater output voltage swing. * Vctl may be adjusted between +2V and +0V to vary the output voltage swing. Device Power Down Instructions 1. Reverse the sequence identified above in steps 1 through 4. For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC465LP5 / 465LP5E v06.1210 GaAs PHEMT MMIC MODULATOR DRIVER AMPLIFIER, DC - 20 GHz 8 Amplifiers - Driver & Gain Block - SMT Notes: For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com 8-8 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Analog Devices Inc.: HMC465LP5ETR HMC465LP5TR