Is Now Part of To learn more about ON Semiconductor, please visit our website at www.onsemi.com Please note: As part of the Fairchild Semiconductor integration, some of the Fairchild orderable part numbers will need to change in order to meet ON Semiconductor's system requirements. Since the ON Semiconductor product management systems do not have the ability to manage part nomenclature that utilizes an underscore (_), the underscore (_) in the Fairchild part numbers will be changed to a dash (-). This document may contain device numbers with an underscore (_). Please check the ON Semiconductor website to verify the updated device numbers. The most current and up-to-date ordering information can be found at www.onsemi.com. Please email any questions regarding the system integration to Fairchild_questions@onsemi.com. ON Semiconductor and the ON Semiconductor logo are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor's product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by ON Semiconductor. "Typical" parameters which may be provided in ON Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. FAN4800A/C, FAN4801/02/02L PFC/PWM Controller Combination Features Description Pin-to-Pin Compatible with ML4800 and FAN4800 and CM6800 and CM6800A PWM Configurable for Current-Mode or Feed-forward Voltage-Mode Operation Internally Synchronized Leading-Edge PFC and Trailing-Edge PWM in one IC The highly integrated FAN4800A/C and FAN4801/02/2L are specially designed for power supplies that consist of boost PFC and PWM. They require very few external components to achieve versatile protections / compensation. They are available in 16-pin DIP and SOP packages. Low Operating Current The PWM can be used in either current or voltage mode. In voltage mode, feed-forward from the PFC output bus can reduce the secondary output ripple. Innovative Switching-Charge Multiplier Divider Compared with older productions, ML4800 and FAN4800, FAN4800A/C and FAN4801/02/02L have lower operation current that save power consumption in external devices. FAN4800A/C and FAN4801/1S/2/2L have accurate 49.9% maximum duty of PWM that makes the hold-up time longer. Brownout protection and PFC soft-start functions are not in ML4800 and FAN4800. Average-Current-Mode for Input-Current Shaping PFC Over-Voltage and Under-Voltage Protections PFC Feedback Open-Loop Protection Peak Current Limiting for PFC Cycle-by-Cycle Current Limiting for PWM Power-On Sequence Control and Soft-Start To evaluate FAN4800A/C, FAN4801/02/2L for replacing existing FAN4800 and ML4800 boards, five things must be completed before the fine-tuning procedure: Brownout Protection Interleaved PFC/PWM Switching FAN4801/02/02L Improve Efficiency at Light Load fRTCT=4*fPFC=4*fPWM for FAN4800A and FAN4801 1. Change RAC resister from the old value to a higher resister: between 6M to 8M. 2. Change RT/CT pin from the existing values to RT=6.8K and CT=1000pF to have fPFC=64KHz, fPWM=64KHz. 3. VRMS pin needs to be 1.224V at VIN=85 VAC for universal input application from line input from 85VAC to 270 VAC. Both poles for the Vrms of FAN4801/02/02L don't need to substantially slower than FAN4800; about 5 to 10 times. 4. At full load, the average VEA needs to ~4.5V and the ripple on the VEA needs to be less than 400mV. 5. Soft-Start pin, the soft-start current has been reduced to half from the FAN4800 capacitor. fRTCT=4*fPFC=2*fPWM for FAN4800C and FAN4802/02L Applications Desktop PC Power Supply Internet Server Power Supply LCD TV, Monitor Power Supply UPS Battery Charger DC Motor Power Supply Monitor Power Supply Related Resources Telecom System Power Supply Distributed Power (c) 2008 Fairchild Semiconductor Corporation FAN4800A/C, FAN4801/02/02L * Rev. 1.0.3 AN-8027 - FAN480X PFC+PWM Combination Controller Application www.fairchildsemi.com 1 FAN4800A/C, FAN4801/02/02L -- PFC/PWM Controller Combination January 2011 Part Number Operating Temperature Range Package Packing Method FAN4800ANY -40C to +105C 16-Pin Dual In-Line Package (DIP) Tube FAN4800CNY -40C to +105C 16-Pin Dual In-Line Package (DIP) Tube FAN4800AMY -40C to +105C 16-Pin Small Outline Package (SOP) Tape & Reel FAN4800CMY -40C to +105C 16-Pin Small Outline Package (SOP) Tape & Reel FAN4801NY -40C to +105C 16-Pin Dual In-Line Package (DIP) Tube FAN4802NY -40C to +105C 16-Pin Dual In-Line Package (DIP)) Tube FAN4802LNY -40C to +105C 16-Pin Dual In-Line Package (DIP)) Tube FAN4801MY -40C to +105C 16-Pin Small Outline Package (SOP) Tape & Reel FAN4802MY -40C to +105C 16-Pin Small Outline Package (SOP) Tape & Reel FAN4802LMY -40C to +105C 16-Pin Small Outline Package (SOP) Tape & Reel Part Number PFC:PWM Frequency Ratio Brownout / In Range In / Out FAN4800ANY 1:1 1.05V / 1.9V N.A FAN4800AMY 1:1 1.05V / 1.9V N.A FAN4800CNY 1:2 1.05V / 1.9V N.A FAN4800CMY 1:2 1.05V / 1.9V N.A FAN4801NY 1:1 1.05V / 1.9V 1.95V / 2.45V FAN4802NY 1:2 1.05V / 1.9V 1.95V / 2.45V FAN4802LNY 1:2 0.9V / 1.65V 1.95V / 2.45V FAN4801MY 1:1 1.05V / 1.9V 1.95V / 2.45V FAN4802MY 1:2 1.05V / 1.9V 1.95V / 2.45V FAN4802LMY 1:2 0.9V / 1.65V 1.95V / 2.45V (c) 2008 Fairchild Semiconductor Corporation FAN4800A/C, FAN4801/02/02L * Rev. 1.0.3 FAN4800A/C, FAN4801/02/02L -- PFC/PWM Controller Combination Ordering Information www.fairchildsemi.com 2 IEA VEA IAC FBPFC ISENSE VREF VDD VRMS VDD SS OPFC FBPWM OPWM RT/CT GND RAMP ILIMIT VREF FAN4800A/C, FAN4801/02/02L -- PFC/PWM Controller Combination Application Diagram FAN4800A/C FAN4801/02/02L Secondary Figure 1. (c) 2008 Fairchild Semiconductor Corporation FAN4800A/C, FAN4801/02/02L * Rev. 1.0.3 Typical Application Current Mode www.fairchildsemi.com 3 IEA VEA IAC FBPFC ISENSE VREF VDD VRMS VDD SS OPFC FBPWM OPWM RT/CT GND RAMP ILIMIT FAN4800A/C, FAN4801/02/02L -- PFC/PWM Controller Combination Application Diagram VREF FAN4800A/C FAN4801/02/02L VREF Secondary Figure 2. (c) 2008 Fairchild Semiconductor Corporation FAN4800A/C, FAN4801/02/02L * Rev. 1.0.3 Typical Application Voltage Mode www.fairchildsemi.com 4 Figure 3. FAN4800A/C Function Block Diagram FAN4800A/C, FAN4801/02/02L -- PFC/PWM Controller Combination Block Diagram Figure 4. FAN4801/02/02L Function Block Diagram (c) 2008 Fairchild Semiconductor Corporation FAN4800A/C, FAN4801/02/02L * Rev. 1.0.3 www.fairchildsemi.com 5 F - Fairchild Logo Z - Plant Code X - 1-Digit Year Code Y - 2-Digit Week Code TT - 2-Digit Die-Run Code T - Package Type (M:SOP) P - Y: Green Package M - Manufacture Flow Code Figure 5. DIP Top Mark F - Fairchild Logo Z - Plant Code X - 1-Digit Year Code Y - 1-Digit Week Code TT - 2-Digit Die-Run Code T - Package Type (M:SOP) P - Y: Green Package M - Manufacture Flow Code FAN4800A/C, FAN4801/02/02L -- PFC/PWM Controller Combination Marking Information Figure 6. SOP Top Mark (c) 2008 Fairchild Semiconductor Corporation FAN4800A/C, FAN4801/02/02L * Rev. 1.0.3 www.fairchildsemi.com 6 Figure 7. Pin Configuration (Top View) Pin Definitions Pin # Name Description 1 IEA Output of PFC Current Amplifier. The signal from this pin is compared with an internal sawtooth to determine the pulse width for PFC gate drive. 2 IAC Input AC Current. For normal operation, this input provides current reference for the multiplier. The suggested maximum IAC is 100A. 3 ISENSE 4 VRMS 5 SS 6 FBPWM 7 RT/CT Oscillator RC Timing Connection. Oscillator timing node; timing set by RT and CT. 8 RAMP PWM RAMP Input. In current mode, this pin functions as the current sense input; when in voltage mode, it is the feed forward sense input from PFC output 380V (feedforward ramp). 9 ILIMIT Peak Current Limit Setting for PWM. The peak current limits setting for PWM. 10 GND 11 OPWM PWM Gate Drive. The totem-pole output drive for PWM MOSFET. This pin is internally clamped under 15V to protect the MOSFET. 12 OPFC PFC Gate Drive. The totem pole output drive for PWM MOSFET. This pin is internally clamped under 15V to protect the MOSFET. 13 VDD Supply. The power supply pin. The threshold voltages for startup and turn-off are 11V and 9.3V, respectively. The operating current is lower than 10mA. 14 VREF Reference Voltage. Buffered output for the internal 7.5V reference. 15 FBPFC 16 VEA PFC Current Sense. The non-inverting input of the PFC current amplifier and the output of multiplier and PFC ILIMIT comparator. Line-Voltage Detection. Line voltage detection. The pin is used for PFC multiplier. PWM Soft-Start. During startup, the SS pin charges an external capacitor with a 10A constant current source. The voltage on FBPWM is clamped by SS during startup. In the event of a protection condition occurring and/or PWM disabled, the SS pin is quickly discharged. FAN4800A/C, FAN4801/02/02L -- PFC/PWM Controller Combination Pin Configuration PWM Feedback Input. The control input for voltage-loop feedback of PWM stage. Ground. Voltage Feedback Input for PFC. The feedback input for PFC voltage loop. The inverting input of PFC error amplifier. This pin is connected to the PFC output through a divider network. Output of PFC Voltage Amplifier. The error amplifier output for PFC voltage feedback loop. A compensation network is connected between this pin and ground. (c) 2008 Fairchild Semiconductor Corporation FAN4800A/C, FAN4801/02/02L * Rev. 1.0.3 www.fairchildsemi.com 7 Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be operable above the recommended operating conditions and stressing the parts to these levels is not recommended. In addition, extended exposure to stresses above the recommended operating conditions may affect device reliability. The absolute maximum ratings are stress ratings only. Symbol Parameter Min. VDD DC Supply Voltage VH SS, FBPWM, RAMP, OPWM, OPFC -0.3 IAC, VRMS, RT/CT, ILIMIT, FBPFC, VEA -0.3 VL VVREF VIEA Unit 30 V 30.0 V 7.0 V 7.5 V 0 VVREF+0.3 V -5.0 VREF IEA Max. VN ISENSE 0.7 V IAC Input AC Current 1 mA IREF VREF Output Current 5 mA 0.5 A IPFC-OUT Peak PFC OUT Current, Source or Sink IPWM-OUT Peak PWM OUT Current, Source or Sink 0.5 A PD Power Dissipation TA < 50C 800 mW JA Thermal Resistance (Junction-to-Air) 80.80 C/W TJ TSTG TL ESD DIP 104.10 C/W Operating Junction Temperature SOP -40 +125 C Storage Temperature Range -55 +150 C +260 C 4.5 kV 1000 V Lead Temperature (Soldering) Human Body Model, JESD22-A114 Electrostatic Discharge Capability Charged Device Model, JESD22-C101 FAN4800A/C, FAN4801/02/02L -- PFC/PWM Controller Combination Absolute Maximum Ratings Notes: 1. All voltage values, except differential voltage, are given with respect to GND pin. 2. Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Recommended Operating Conditions The Recommended Operating Conditions table defines the conditions for actual device operation. Recommended operating conditions are specified to ensure optimal performance to the datasheet specifications. Fairchild does not recommend exceeding them or designing to Absolute Maximum Ratings. Symbol TA Parameter Operating Ambient Temperature (c) 2008 Fairchild Semiconductor Corporation FAN4800A/C, FAN4801/02/02L * Rev. 1.0.3 Min. Max. Unit -40 +105 C www.fairchildsemi.com 8 VDD=15V, TA=25C, RT=6.8k, CT=1000pF unless noted operating specifications. Symbol Parameter Conditions Min. Typ. Max. Units 30 80 A 2.0 2.6 5.0 mA 11 12 V 1.9 V VDD Section IDD ST Startup Current VDD=VTH-ON-0.1V; OPFC OPWM Open IDD-OP Operating Current VDD=13V; OPFC OPWM Open VTH-ON Turn-On Threshold Voltage 10 Hysteresis 1.5 VDD OVP 27 VTH VDD-OVP VDD-OVP VDD OVP Hysteresis 28 29 1 V V Oscillator fOSC-RT/CT RT/CT Frequency RT=6.8k, CT=1000pF PFC & PWM Frequency 240 256 268 60 64 67 120 128 134 kHz fOSC FAN4800C,FAN4802/02L PWM Frequency RT=6.8k, CT=1000pF fDV Voltage Stability 11V VDD 22V 2 % fDT Temperature Stability -40C ~ +105C 2 % fTV Total Variation (PFC and PWM)(3) Line, Temperature 70 kHz fRV Ramp Voltage(3) Valley to Peak Discharge Current VRAMP=0V, VRT/CT=2.5V IDischarge 58 2.8 kHz V 6.5 15 mA 50 75 kHz 600 800 ns 7.5 7.6 V 30 50 mV 25 mV 0.5 % fRANGE Frequency Range(3) tPFCD PFC Dead Time RT=6.8k, CT=1000pF 400 VVREF Reference Voltage IREF=0mA, CREF=0.1F 7.4 VVREF1 Load Regulation of Reference Voltage CREF=0.1F, IREF=0mA to 3.5mA VVDD=14V, Rise/Fall Time > 20s VVREF2 Line Regulation of Reference Voltage CREF=0.1F, VVDD=11V to 22V Temperature Stability(3) -40C ~ +105C VREF VVREF-DT VVREF-TV (3) Total Variation (3) 0.4 Line, Load, Temperature 7.35 7.65 V 25 mV VVREF-LS Long-Term Stability TJ=125C, 0 ~ 1000HRs 5 IREF-MAX. Maximum Current VVREF > 7.35V 5 IOS Output Short Circuit(3) FAN4800A/C, FAN4801/02/02L -- PFC/PWM Controller Combination Electrical Characteristics mA 25 mA PFC OVP Comparator VPFC-OVP VPFC-OVP Over-Voltage Protection 2.70 2.75 2.80 V PFC OVP Hysteresis 200 250 300 mV 0.2 0.3 0.4 V Voltage Level on FBPFC to Enable OPWM During Startup 2.3 2.4 2.5 V Hysteresis 1.15 1.25 1.35 V Low-Power Detect Comparator VEAOFF VEA Voltage OFF OPFC VIN OK Comparator VRD-FBPFC VRD-FBPFC (c) 2008 Fairchild Semiconductor Corporation FAN4800A/C, FAN4801/02/02L * Rev. 1.0.3 www.fairchildsemi.com 9 VDD=15V, TA=25C, RT=6.8k, CT=1000pF unless noted operating specifications. Symbol Parameter Conditions Min. Typ. Max. Units 6 V 2.55 V 90 mho Voltage Error Amplifier FBPFC Input Voltage Range(3) Vref Reference Voltage AV (3) 0 at T=25C 2.45 35 42 Transconductance VNONINV=VINV, VVEA=3.75V at T=25C 50 70 IFBPFC-L Maximum Source Current VFBPFC=2V, VVEA=1.5V 40 50 IFBPFC-H Maximum Sink Current VFBPFC=3V, VVEA=6V Gmv IBS Open-Loop Gain 2.50 -50 Input Bias Current -1 VVEA-H Output High Voltage on VVEA 5.8 VVEA-L Output Low Voltage on VVEA dB A -40 A 1 A 6 0.1 V 0.4 V 0.7 V 100 mho 10 mV 7.4 8.0 V 0.1 0.4 V -35 A Current Error Amplifier VISENSE GmI Input Voltage Range (ISENSE Pin)(3) -1.5 Transconductance VNONINV=VINV, VIEA=3.75V 78 VOFFSET Input Offset Voltage VVEA=0V, IAC Open -10 VIEA-H Output High Voltage VIEA-L Output Low Voltage 6.8 IL Source Current VISENSE=-0.6V, VIEA=1.5V IH Sink Current VISENSE=+0.6V, VIEA=4.0V AI Open-Loop Gain(3) 35 88 50 -50 40 A 50 dB FAN4800A/C, FAN4801/02/02L -- PFC/PWM Controller Combination Electrical Characteristics (Continued) Tri-Fault Detect tFBPFC_OPEN Time to FBPFC Open(3) VPFC-UVP PFC Feedback UnderVoltage Protection VFBPFC=VPFC-UVP to FBPFC OPEN, 470pF from FBPFC to GND 0.4 2 4 ms 0.5 0.6 V 100 A Gain Modulator IAC GAIN BW Vo(gm) Input for AC Current(3) GAIN Modulator(4) Multiplier Linear Range IAC=17.67A, VRMS=1.080V VFBPFC=2.25V, at T=25C 7.50 9.00 10.50 IAC=20A, VRMS=1.224V VFBPFC=2.25V, at T=25C 6.30 7.00 7.70 IAC=25.69A, VRMS=1.585V VFBPFC=2.25V, at T=25C 3.80 4.20 4.60 IAC=51.62A, VRMS=3.169V VFBPFC=2.25V, at T=25C 0.95 1.05 1.16 IAC=62.23A, VRMS=3.803V VFBPFC=2.25V, at T=25C 0.66 0.73 0.80 Bandwidth(3) IAC=40A Output Voltage=5.7k x (ISENSE-IOFFSET)(3) IAC=20A, VRMS=1.224V VFBPFC=2.25V, at T=25C (c) 2008 Fairchild Semiconductor Corporation FAN4800A/C, FAN4801/02/02L * Rev. 1.0.3 0 2 0.74 0.82 kHz 0.90 V www.fairchildsemi.com 10 VDD=15V, TA=25C, RT=6.8k, CT=1000pF unless noted operating specifications. Symbol Parameter Conditions Min. Typ. Max. Units -1.25 -1.15 -1.05 PFC ILIMIT Comparator VPFC-ILIMIT Peak Current Limit Threshold Voltage, Cycle-by-Cycle Limit IAC=17.67A, VRMS=1.08V VFBPFC=2.25V, at T=25C 200 Gate Output Clamping Voltage VDD=22V 13 VGATE-L Gate Low Voltage VDD=15V; IO=100mA VGATE-H Gate High Voltage VDD=13V; IO=100mA 8 tr Gate Rising Time VDD=15V; CL=4.7nF; O/P=2V to 9V 40 70 120 ns tf 110 ns Vpk PFC ILIMIT-Gain Modulator Output V mV PFC Output Driver VGATE-CLAMP 15 17 V 1.5 V V Gate Falling Time VDD=15V; CL=4.7nF; O/P=9V to 2V 40 60 DPFC-MAX Maximum Duty Cycle VIEA<1.2V 94 97 DPFC-MIN Minimum Duty Cycle VIEA>4.5V % 0 % Brownout VRMS-UVL VRMS Threshold Low VRMS-UVH VRMS Threshold High VRMS-UVP tUVP Hysteresis FAN4800A/C, FAN4801/02 1.00 1.05 1.10 V FAN4802L 0.85 0.90 0.95 V FAN4800A/C, FAN4801/02 1.85 1.90 1.95 V FAN4802L 1.60 1.65 1.70 V FAN4800A/C, FAN4801/02 750 850 950 mV FAN4802L 650 750 850 mV 340 410 480 ms 9.5 10.0 10.5 Under-Voltage Protection Delay Time FAN4800A/C, FAN4801/02/02L -- PFC/PWM Controller Combination Electrical Characteristics (Continued) Soft-Start VSS-MAX Maximum Voltage ISS Soft-Start Current VDD=15V 10 V A PWM ILIMIT Comparator VPWM-ILIMIT tPD tPWM-Bnk Threshold Voltage 0.95 Delay to Output 1.00 1.05 250 Leading-Edge Blanking Time V ns 170 250 350 ns Range (FAN4801/02/02L) VRMS-L RMS AC Voltage Low When VRMS=1.95V at132VRMS 1.90 1.95 2.00 V VRMS-H RMS AC Voltage High When VRMS=2.45V at150VRMS 2.40 2.45 2.50 V VEA-L VEA Low When VVEA=1.95V at 30% Loading, When VVEA=2.80V at 60% Loading 1.90 1.95 2.00 V VEA-H VEA High When VVEA=2.45V at 40% Loading, When VVEA=3.35V at 70% Loading 2.40 2.45 2.50 V Two-Level Current FBPFC Two-Level Current 18 20 22 A Itc (c) 2008 Fairchild Semiconductor Corporation FAN4800A/C, FAN4801/02/02L * Rev. 1.0.3 www.fairchildsemi.com 11 VDD=15V, TA=25C, RT=6.8k, CT=1000pF unless noted operating specifications. Symbol Parameter Conditions Min. Typ. Max. Units 13 15 17 V 1.5 V PWM Output Driver VGATE-CLAMP Gate Output Clamping Voltage VDD=22V VGATE-L Gate Low Voltage VDD=15V; IO=100mA VGATE-H Gate High Voltage VDD=13V; IO=100mA 8 tr Gate Rising Time VDD=15V; CL=4.7nF 30 60 120 ns tf Gate Falling Time VDD=15V; CL=4.7nF 30 50 110 ns Maximum Duty Cycle 49.0 49.5 50.0 % PWM Comparator Level Shift 1.3 1.5 1.8 V DPWM-MAX VPWM-LS Notes: 3. This parameter, although guaranteed by design, is not 100% production tested. 4. Gain=K x 5.3 x (VRMS2)-1; K=(ISENSE IOFFSET) x [IAC x (VEA 0.7V)]-1; VEA(MAX.)=5.6V. (c) 2008 Fairchild Semiconductor Corporation FAN4800A/C, FAN4801/02/02L * Rev. 1.0.3 V FAN4800A/C, FAN4801/02/02L -- PFC/PWM Controller Combination Electrical Characteristics (Continued) www.fairchildsemi.com 12 20.0 2.96 18.0 2.94 16.0 2.92 2.90 IDD-OP(uA) IDD-ST(uA) 14.0 12.0 10.0 8.0 6.0 2.88 2.86 2.84 4.0 2.82 2.0 2.80 0.0 2.78 -40 -25 -10 5 20 35 50 65 80 95 110 125 -40 -25 -10 Figure 8. IDD-ST vs. Temperature 2.0 11.3 1.9 VTH(V) VTH-ON (V) 95 110 125 1.8 11.2 11.1 11.0 1.7 1.6 1.5 10.9 1.4 1.3 10.8 -40 -25 -10 5 20 35 50 65 80 95 -40 -25 -10 110 125 28.04 65.0 28.02 64.9 28.00 FOSC-FAN4801/1S(kHz) 27.96 27.94 27.92 27.90 35 50 65 80 95 110 125 64.7 64.6 64.5 64.4 64.3 27.88 27.86 5 20 35 50 65 80 95 64.2 -40 110 125 Figure 12. VDD-OVP vs. Temperature -25 -10 5 20 35 50 65 80 95 110 125 Figure 13. fOSC-FAN4801/1S vs. Temperature 655 129.8 650 129.6 645 129.4 640 tPFCD(ns) 130.0 129.2 129.0 635 630 128.8 625 128.6 620 128.4 -40 -25 -10 20 64.8 27.98 -40 -25 -10 5 Figure 11. VTH vs. Temperature Figure 10. VTH-ON vs. Temperature VDD-OVP(V) 20 35 50 65 80 Figure 9. IDD-OP vs. Temperature 11.4 FOSC-FAN4802/2L(kHz) 5 FAN4800A/C, FAN4801/02/02L -- PFC/PWM Controller Combination Typical Characteristics 615 5 20 35 50 65 80 95 110 125 -40 -25 -10 Figure 14. fOSC-FAN4802/2L vs. Temperature (c) 2008 Fairchild Semiconductor Corporation FAN4800A/C, FAN4801/02/02L * Rev. 1.0.3 5 20 35 50 65 80 95 110 125 Figure 15. tPFCD vs. Temperature www.fairchildsemi.com 13 6 7.520 7.515 5 7.510 VVREF1(mV) VVREF(V) 7.505 7.500 7.495 7.490 4 3 2 7.485 1 7.480 7.475 0 -40 -25 -10 5 20 35 50 65 80 -40 -25 -10 95 110 125 0.18 50 65 80 95 110 125 21.0 0.16 0.14 20.5 IREF-MAX.(mA) VVREF2(mV) 35 21.5 0.20 0.12 0.10 0.08 0.06 20.0 19.5 19.0 0.04 0.02 18.5 0.00 -0.02 18.0 -40 -25 -10 5 -40 -25 -10 20 35 50 65 80 95 110 125 Figure 18. VVREF2 vs. Temperature 2.742 252.2 2.740 252.0 2.738 2.736 2.734 2.732 50 65 80 95 110 125 251.8 251.6 251.4 251.2 250.8 5 20 35 50 65 80 95 110 125 -40 -25 -10 5 20 35 50 65 80 95 110 125 Figure 21. VPFC-OVP vs. Temperature Figure 20. VPFC-OVP vs. Temperature 1.275 2.398 1.270 VRD-FBPFC(V) 2.400 2.396 2.394 2.392 2.390 1.265 1.260 1.255 1.250 1.245 2.388 -40 -25 -10 20 35 251.0 2.730 -40 -25 -10 5 Figure 19. IREF-MAX. vs. Temperature VPFC-OVP(mV) VPFC-OVP(V) 20 Figure 17. VVREF1 vs. Temperature Figure 16. VVREF vs. Temperature VRD-FBPFC(V) 5 FAN4800A/C, FAN4801/02/02L -- PFC/PWM Controller Combination Typical Characteristics 1.240 5 20 35 50 65 80 95 110 125 -40 -25 -10 20 35 50 65 80 95 110 125 Figure 23. VRD-FBPFC vs. Temperature Figure 22. VRD-FBPFC vs. Temperature (c) 2008 Fairchild Semiconductor Corporation FAN4800A/C, FAN4801/02/02L * Rev. 1.0.3 5 www.fairchildsemi.com 14 74 2.502 2.500 73 Gmv(umho) Vref(V) 2.498 2.496 2.494 73 72 2.492 72 2.490 2.488 71 -40 -25 -10 5 20 35 50 65 80 95 110 125 -40 Figure 24. Vref vs. Temperature 4.5 94 4.0 92 5 20 35 50 65 80 95 110 125 90 3.0 GmI(umho) VOFFSET(mV) -10 Figure 25. GmV vs. Temperature 3.5 2.5 2.0 1.5 88 86 84 82 1.0 80 0.5 0.0 78 -40 -25 -10 5 20 35 50 65 80 -40 -25 -10 95 110 125 Figure 26. VOFFSET vs. Temperature 5 20 35 50 65 80 95 110 125 Figure 27. GmI vs. Temperature 7.10 6.1 7.05 6.0 7.00 5.9 Rmul(k) 6.95 GAIN2 -25 FAN4800A/C, FAN4801/02/02L -- PFC/PWM Controller Combination Typical Characteristics 6.90 6.85 5.8 5.7 5.6 6.80 5.5 6.75 6.70 5.4 -40 -25 -10 5 20 35 50 65 80 95 110 125 -40 -25 -10 Figure 28. GAIN2 vs. Temperature 20 35 50 65 80 95 110 125 Figure 29. Rmul vs. Temperature -1.1775 295 -1.1780 290 -1.1785 285 -1.1790 Vpk(mV) VPFC-ILIMIT(V) 280 -1.1795 -1.1800 -1.1805 -1.1810 275 270 265 -1.1815 260 -1.1820 255 250 -1.1825 -40 -25 -10 5 5 20 -40 -25 -10 35 50 65 80 95 110 125 20 35 50 65 80 95 110 125 Figure 31. Vpk vs. Temperature Figure 30. VPFC-ILIMIT vs. Temperature (c) 2008 Fairchild Semiconductor Corporation FAN4800A/C, FAN4801/02/02L * Rev. 1.0.3 5 www.fairchildsemi.com 15 1.010 10.1 1.009 10.0 9.9 9.8 1.007 ISS(uA) VPWM-ILIMIT (V) 1.008 1.006 1.005 9.7 9.6 9.5 9.4 1.004 9.3 1.003 9.2 1.002 9.1 -40 -25 -10 5 -40 -25 -10 20 35 50 65 80 95 110 125 Figure 32. VPWM-ILIMIT vs. Temperature 1.048 867.5 1.047 867.0 1.046 866.5 VRMS-UVP(mV) VRMS-UVP(V) 1.044 1.043 1.042 1.041 50 65 80 95 110 125 866.0 865.5 865.0 864.5 864.0 863.5 1.040 863.0 1.039 862.5 1.038 862.0 -40 -25 -10 5 -40 -25 -10 20 35 50 65 80 95 110 125 5 20 35 50 65 80 95 110 125 Figure 35. VRMS-UVP vs. Temperature Figure 34. VRMS-UVP vs. Temperature 1.940 2.446 1.939 2.445 2.444 1.938 2.443 1.937 VRMS-H(V) VRMS-L(V) 20 35 Figure 33. ISS vs. Temperature 1.045 1.936 1.935 1.934 2.442 2.441 2.440 2.439 1.933 2.438 1.932 2.437 2.436 1.931 -40 -25 -10 5 2.435 20 35 50 65 80 95 110 125 -40 -25 -10 Figure 36. VRMS-L vs. Temperature 5 20 35 50 65 80 95 110 125 Figure 37. VRMS-H vs. Temperature 1.942 2.436 1.940 2.434 1.938 2.432 VEA-H(V) VEA-L(V) 5 FAN4800A/C, FAN4801/02/02L -- PFC/PWM Controller Combination Typical Characteristics 1.936 1.934 2.430 2.428 1.932 2.426 1.930 2.424 1.928 -40 -25 -10 -40 -25 -10 5 5 20 35 50 65 80 95 20 35 50 65 80 95 110 125 Figure 38. VEA-L vs. Temperature (c) 2008 Fairchild Semiconductor Corporation FAN4800A/C, FAN4801/02/02L * Rev. 1.0.3 110 125 Figure 39. VEA-H vs. Temperature www.fairchildsemi.com 16 14.4 14.6 14.3 14.5 14.2 VGATE-CLAMP-PWM(V) VGATE-CLAMP-PFC(V) 14.7 14.4 14.3 14.2 14.1 14.1 14.0 13.9 13.8 14.0 13.7 13.9 -40 -25 -10 5 20 35 50 65 80 13.6 95 110 125 -40 -25 -10 Figure 40. VGATE-CLAMP-PFC vs. Temperature 5 20 35 50 65 80 95 110 125 Figure 41. VGATE-CLAMP-PWM vs. Temperature 96.06 49.80 96.04 49.75 DPWM-MAX(%) DPFC-MAX(%) 96.02 96.00 95.98 95.96 95.94 49.70 49.65 49.60 49.55 95.92 95.90 49.50 95.88 -40 -25 -10 -40 -25 -10 5 20 35 50 5 20 35 50 65 80 95 65 80 95 110 125 Figure 42. DPFC-MAX vs. Temperature 110 125 Figure 43. DPWM-MAX vs. Temperature 1.460 21.0 20.8 FAN4800A/C, FAN4801/02/02L -- PFC/PWM Controller Combination Typical Characteristics 1.455 VPWM-LS(V) 20.6 Itc(uA) 20.4 20.2 20.0 1.450 1.445 1.440 19.8 1.435 19.6 19.4 1.430 -40 -25 -10 5 20 35 50 65 80 95 110 125 -40 -25 -10 Figure 44. Itc vs. Temperature (c) 2008 Fairchild Semiconductor Corporation FAN4800A/C, FAN4801/02/02L * Rev. 1.0.3 5 20 35 50 65 80 95 110 125 Figure 45. VPWM-LS vs. Temperature www.fairchildsemi.com 17 The FAN4800A/C and FAN4801/02/02L consist of an average current controlled, continuous boost Power Factor Correction (PFC) front-end and a synchronized Pulse Width Modulator (PWM) back-end. The PWM can be used in current or voltage mode. In voltage mode, feed forward from the PFC output bus can be used to improve the line regulation of PWM. In either mode, the PWM stage uses conventional trailing-edge, duty-cycle modulation. This propriety leading/trailing edge modulation results in a higher usable PFC error amplifier bandwidth and can significantly reduce the size of the PFC DC bus capacitor. IGAINMOD VRMS 2 K (1) Note that the output current of the gain modulator is limited around 159A and the maximum output voltage of the gain modulator is limited to 159A x 5.7K=0.906V. This 0.906V also determines the maximum input power. However, IGAINMOD cannot be measured directly from ISENSE. ISENSE=IGAINMOD - IOFFSET and IOFFSET can only be measured when VEA is less than 0.5V and IGAINMOD is 0A. Typical IOFFSET is around 31A ~ 48A. The synchronization of the PWM with the PFC simplifies the PWM compensation due to the controlled ripple on the PFC output capacitor (the PWM input capacitor). The PWM section of the FAN4800A, FAN4801/1S operates at the same frequency as the PFC; and FAN4800C, FAN4802/2L operates at double with PFC. Selecting RAC for IAC Pin The IAC pin is the input of the gain modulator and also a current mirror input and requires current input. Selecting a proper resistor RAC provides a good sine wave current derived from the line voltage and helps program the maximum input power and minimum input line voltage. RAC=VIN peak x 56K. For example, if the minimum line voltage is 75VAC, the RAC=75 x 1.414 x 56K=6M. In addition to power factor correction, a number of protection features are built into this series. They include soft-start, PFC over-voltage protection, peak current limiting, brownout protection, duty cycle limiting, and under-voltage lockout (UVLO). Current Amplifier Error, IEA Gain Modulator The current error amplifier's output controls the PFC duty cycle to keep the average current through the boost inductor a linear function of the line voltage. At the inverting input to the current error amplifier, the output current of the gain modulator is summed with a current, which results in a negative voltage being impressed upon the ISENSE pin. The gain modulator is the heart of the PFC, as the circuit block controls the response of the current loop to line voltage waveform and frequency, RMS line voltage, and PFC output voltages. There are three inputs to the gain modulator: 1. A current representing the instantaneous input voltage (amplitude and wave shape) to the PFC. The rectified AC input sine wave is converted to a proportional current via a resistor and is fed into the gain modulator at IAC. Sampling current in this way minimizes ground noise, required in high-power, switching-power conversion environments. The gain modulator responds linearly to this current. The negative voltage on ISENSE represents the sum of all currents flowing in the PFC circuit and is typically derived from a current sense resistor in series with the negative terminal of the input bridge rectifier. The inverting input of the current error amplifier is a virtual ground. Given this fact, and the arrangement of the duty cycle modulator polarities internal to the PFC, an increase in positive current from the gain modulator causes the output stage to increase its duty cycle until the voltage on ISENSE is adequately negative to cancel this increased current. Similarly, if the gain modulator's output decreases, the output duty cycle decreases to achieve a less negative voltage on the ISENSE pin. 2. A voltage proportional to the long-term RMS AC line voltage, derived from the rectified line voltage after scaling and filtering. This signal is presented to the gain modulator at VRMS. The output of the gain modulator is inversely proportional to VRMS (except at unusually low values of VRMS, where special gain contouring takes over to limit power dissipation of the circuit components under brownout conditions). PFC Cycle-By-Cycle Current Limiter 3. The output of the voltage error amplifier, VEA. The gain modulator responds linearly to variations in this voltage. As well as being a part of the current feedback loop, the ISENSE pin is a direct input to the cycle-by-cycle current limiter for the PFC section. If the input voltage at this pin is less than -1.15V, the output of the PFC is disabled until the protection flip-flop is reset by the clock pulse at the start of the next PFC power cycle. The output of the gain modulator is a current signal, in the form of a full wave rectified sinusoid at twice the line frequency. This current is applied to the virtual ground (negative) input of the current error amplifier. In this way, the gain modulator forms the reference for the current error loop and ultimately controls the instantaneous current draw of the PFC from the power line. The general form of the output of the gain modulator is: (c) 2008 Fairchild Semiconductor Corporation FAN4800A/C, FAN4801/02/02L * Rev. 1.0.3 IAC (VEA 0.7) FAN4800A/C, FAN4801/02/02L -- PFC/PWM Controller Combination Functional Description www.fairchildsemi.com 18 Error Amplifier Compensation To improve power supply reliability, reduce system component count, and simplify compliance to UL 1950 safety standards, the FAN4800A/C, FAN4801/02/02L includes TriFault Detect. This feature monitors FBPFC for certain PFC fault conditions. The PWM loading of the PFC can be modeled as a negative resistor because an increase in the input voltage to the PWM causes a decrease in the input current. This response dictates the proper compensation of the two transconductance error amplifiers. Figure 46 shows the types of compensation networks most commonly used for the voltage and current error amplifiers, along with their respective return points. The current-loop compensation is returned to VREF to produce a soft-start characteristic on the PFC: As the reference voltage increases from 0V, it creates a differentiated voltage on IEA, which prevents the PFC from immediately demanding a full duty cycle on its boost converter. Complete design is referred in application note AN-6078SC. In a feedback path failure, the output of the PFC could exceed safe operating limits. With such a failure, FBPFC exceeds its normal operating area. Should FBPFC go too LOW, too HIGH, or OPEN, TriFault Detect senses the error and terminates the PFC output drive. TriFault detect is an entirely internal circuit. It requires no external components to serve its protective function. PFC Over-Voltage Protection There is an RC filter between RSENSE and ISENSE pin. There are two reasons to add a filter at the ISENSE pin: In the FAN4800A/C, FAN4801/02/02L, the PFC OVP comparator serves to protect the power circuit from being subjected to excessive voltages if the load changes suddenly. A resistor divider from the highvoltage DC output of the PFC is fed to FBPFC. When the voltage on FBPFC exceeds 2.75V, the PFC output driver is shut down. The PWM section continues to operate. The OVP comparator has 250mV of hysteresis and the PFC does not restart until the voltage at FBPFC drops below 2.50V. VDD OVP can also serve as a redundant PFC OVP protection. VDD OVP threshold is 28V with 1V hysteresis. 1. Protection: During startup or inrush current conditions, there is a large voltage across RSENSE, which is the sensing resistor of the PFC boost converter. It requires the ISENSE filter to attenuate the energy. 2. To reduce L, the boost inductor: The ISENSE filter also can reduce the boost inductor value since the ISENSE filter behaves like an integrator before the ISENSE pin, which is the input of the current error amplifier, IEA. The ISENSE filter is an RC filter. The resistor value of the ISENSE filter is between 100 and 50 because IOFFSET x RFILTER can generate a negative offset voltage of IEA. Selecting an RFILTER equal to 50 keeps the offset of the IEA less than 3mV. Design the pole of ISENSE filter at fPFC/6, one sixth of the PFC switching frequency, so the boost inductor can be reduced six times without disturbing the stability. The capacitor of the ISENSE filter, CFILTER, is approximately 100nF. Selecting PFC RSENSE RSENSE is the sensing resistor of the PFC boost converter. During the steady state, line input current x RSENSE equals IGAINMOD x 5.7K. At full load, the average VEA needs to around 4.5V and ripple on the VEA needs to be less than 400mV. Choose the resistance of the sensing resistor: Rsense 4.5 0.7 5.7K IAC Gain VIN 2 5.6 0.7 Line input Power 2 FAN4800A/C, FAN4801/02/02L -- PFC/PWM Controller Combination TriFault DetectTM (2) where 5.6 is VEA maximum output. PFC Soft-Start PFC startup is controlled by VEA level. Before FBPFC voltage reaches 2.4V, the VEA level is around 2.8V. At 90VAC, the PFC soft-start time is 90ms. PFC Brownout The AC UVP comparator monitors the AC input voltage. The FAN4800A/C, FAN4801/02 disables PFC as lower AC input such that the VRMS is less than 1.05V. The brownout voltage of FAN4802L is lower than FAN4801/1S/2, such that the VRMS is less than 0.9V. Figure 46. Compensation Network Connection for the Voltage and Current Error Amplifiers (c) 2008 Fairchild Semiconductor Corporation FAN4800A/C, FAN4801/02/02L * Rev. 1.0.3 www.fairchildsemi.com 19 Pulse Width Modulator (PWM) To improve the efficiency, the system can reduce PFC switching loss at low line and light load by reducing the PFC output voltage. The two-level PFC output of FAN4801/02/02L can be programmable. The operation of the PWM section is straightforward, but there are several points that should be noted. Foremost among these is the inherent synchronization of PWM with the PFC section of the device, from which it also derives its basic timing. The PWM is capable of current-mode or voltage-mode operation. In currentmode applications, the PWM ramp (RAMP) is usually derived directly from a current sensing resistor or current transformer in the primary of the output stage. It is thereby representative of the current flowing in the converter's output stage. ILIMIT, which provides cycle-bycycle current limiting, is typically connected to RAMP in such applications. For voltage-mode operation and certain specialized applications, RAMP can be connected to a separate RC timing network to generate a voltage ramp against which FBPWM is compared. Under these conditions, the use of voltage feed-forward from the PFC bus can assist in line regulation accuracy and response. As in current-mode operation, the ILIMIT input is used for output stage over-current protection. No voltage error amplifier is included in the PWM stage, as this function is generally performed on the output side of the PWM's isolation boundary. To facilitate the design of opto-coupler feedback circuitry, an offset has been built into the PWM's RAMP input that allows FBPWM to command a 0% duty cycle for input voltages below typical 1.5V. As Figure 47 shows, FAN4801/02/02L detect VEA pin and VRMS pin to determine the system operates low line and light load or not. At the second-level PFC, there is a current of 20A through RF2 from FBPFC pin. So the second-level PFC output voltage can be calculated as. RF 1 RF 2 (2.5V 20uA RF 2 ) (3) RF 2 For example, if the second-level PFC output voltage is expected as 300V and normal voltage is 387V, according to the equation, RF2 is 28k RF1 is 4.3M. Output The programmable range of second level PFC output voltage is 340V ~ 300V. PWM Cycle-By-Cycle Current Limiter The ILIMIT pin is a direct input to the cycle-by-cycle current limiter for the PWM section. Should the input voltage at this pin ever exceed 1V, the output flip-flop is reset by the clock pulse at the start of the next PWM power cycle. When the ILIMIT triggers the cycle-by-cycle bi-cycle current, it limits the PWM duty cycle mode and the power dissipation is reduced during the dead-short condition. Figure 47. Two-Level PFC Scheme Oscillator (RT/CT) The oscillator frequency is determined by the values of RT and CT, which determine the ramp and off-time of the oscillator output clock: VIN OK Comparator 1 fRT / CT (4) tRT / CT tDEAD The dead time of the oscillator is derived from the following equation: The VIN OK comparator monitors the DC output of the PFC and inhibits the PWM if the voltage on FBPFC is less than its nominal 2.4V. Once the voltage reaches 2.4V, which corresponds to the PFC output capacitor being charged to its rated boost voltage, the soft-start begins. VREF 1 tRT / CT CT RT ln VREF 3.8 at VREF=7.5V and tRT/CT=CT x RT x 0.56. PWM Soft-Start (SS) (5) PWM startup is controlled by selection of the external capacitor at soft-start. A current source of 10A supplies the charging current for the capacitor and startup of the PWM begins at 1.5V. The dead time of the oscillator is determined using: 2.8V CT 360 CT (6) 7.78mA The dead time is so small (tRT/CT>>tDEAD) that the operating frequency can typically be approximated by: tDEAD fRT / CT 1 tRT / CT (c) 2008 Fairchild Semiconductor Corporation FAN4800A/C, FAN4801/02/02L * Rev. 1.0.3 FAN4800A/C, FAN4801/02/02L -- PFC/PWM Controller Combination Two-Level PFC Function (7) www.fairchildsemi.com 20 Leading/Trailing Modulation When the PWM section is used in current mode, RAMP is generally used as the sampling point for a voltage, representing the current in the primary of the PWM's output transformer. The voltage is derived either from a current sensing resistor or a current transformer. In voltage mode, RAMP is the input for a ramp voltage generated by a second set of timing components (RRAMP, CRAMP) that have a minimum value of 0V and a peak value of approximately 6V. In voltage mode, feed forward from the PFC output bus is an excellent way to derive the timing ramp for the PWM stage. Conventional PWM techniques employ trailing-edge modulation, in which the switch turns on right after the trailing edge of the system clock. The error amplifier output is then compared with the modulating ramp up. The effective duty cycle of the trailing edge modulation is determined during the on-time of the switch. In the case of leading-edge modulation, the switch is turned off exactly at the leading edge of the system clock. When the modulating ramp reaches the level of the error amplifier output voltage, the switch is turned on. The effective duty-cycle of the leading-edge modulation is determined during off-time of the switch. Generating VDD After turning on the FAN4800A/C, FAN4801/02/02L at 11V, the operating voltage can vary from 9.3V to 28V. The threshold voltage of the VDD OVP comparator is 28V and its hysteresis is 1V. When VDD reaches 28V, OPFC is LOW, and the PWM section is not disturbed. There are two ways to generate VDD: use auxiliary power supply around 15V or use bootstrap winding to self-bias the FAN4800A/C, FAN4801/02/02L system. The bootstrap winding can be taped from the PFC boost choke or the transformer of the DC-to-DC stage. (c) 2008 Fairchild Semiconductor Corporation FAN4800A/C, FAN4801/02/02L * Rev. 1.0.3 FAN4800A/C, FAN4801/02/02L -- PFC/PWM Controller Combination PWM Control (RAMP) www.fairchildsemi.com 21 19.68 18.66 16 A 9 6.60 6.09 1 8 (0.40) TOP VIEW 0.38 MIN 5.33 MAX 8.13 7.62 3.42 3.17 3.81 2.92 2.54 0.35 0.20 0.58 A 0.35 1.78 1.14 15 0 FAN4800A/C, FAN4801/02/02L -- PFC/PWM Controller Combination Physical Dimensions 8.69 17.78 SIDE VIEW NOTES: UNLESS OTHERWISE SPECIFIED A THIS PACKAGE CONFORMS TO JEDEC MS-001 VARIATION BB B) ALL DIMENSIONS ARE IN MILLIMETERS. C) DIMENSIONS ARE EXCLUSIVE OF BURRS, MOLD FLASH, AND TIE BAR PROTRUSIONS D) CONFORMS TO ASME Y14.5M-1994 E) DRAWING FILE NAME: N16EREV1 Figure 48. 16-Pin Dual In-Line Package (DIP) Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner without notice. Please note the revision and/or date on the drawing and contact a Fairchild Semiconductor representative to verify or obtain the most recent revision. Package specifications do not expand the terms of Fairchild's worldwide terms and conditions, specifically the warranty therein, which covers Fairchild products. Always visit Fairchild Semiconductor's online packaging area for the most recent package drawings: http://www.fairchildsemi.com/packaging/. (c) 2008 Fairchild Semiconductor Corporation FAN4800A/C, FAN4801/02/02L * Rev. 1.0.3 www.fairchildsemi.com 22 FAN4800A/C, FAN4801/02/02L -- PFC/PWM Controller Combination Physical Dimensions (Continued) Figure 49. 16-Pin Small Outline Package (SOIC) Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner without notice. Please note the revision and/or date on the drawing and contact a Fairchild Semiconductor representative to verify or obtain the most recent revision. Package specifications do not expand the terms of Fairchild's worldwide terms and conditions, specifically the warranty therein, which covers Fairchild products. Always visit Fairchild Semiconductor's online packaging area for the most recent package drawings: http://www.fairchildsemi.com/packaging/. (c) 2008 Fairchild Semiconductor Corporation FAN4800A/C, FAN4801/02/02L * Rev. 1.0.3 www.fairchildsemi.com 23 FAN4800A/C, FAN4801/02/02L -- PFC/PWM Controller Combination (c) 2008 Fairchild Semiconductor Corporation FAN4800A/C, FAN4801/02/02L * Rev. 1.0.3 www.fairchildsemi.com 24 ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor's product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by ON Semiconductor. "Typical" parameters which may be provided in ON Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor 19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com (c) Semiconductor Components Industries, LLC N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5817-1050 www.onsemi.com 1 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative www.onsemi.com