1
Zarlink Semiconductor Inc.
Zarlink, ZL and the Zarlink Semiconductor logo are trademarks of Zarlink Semiconductor Inc.
Copyright 2003-2004, Zarlink Semiconductor Inc. All Rights Reserved.
Features
Independent multiple channels of echo
cancellation; from 32 channels of 64 ms to 16
channels of 128 ms with the ability to mix
channels at 128 ms or 64 ms in any combination
Independent Power Down mode for ea ch group
of 2 channels for power management
Fully compliant to ITU-T G.165, G.168 (2000) and
(2002) specifications
Passed all AT&T voice quality tests for carrier
grade echo canceller.
Compatible to ST-BUS and GCI interface at
2 Mbps serial PCM
PCM coding, µ/A-Law ITU-T G.711 or sign
magnitude
Per channel Fax/Modem G.164 2100Hz or G.165
2100Hz phase reversal Tone Disable
Per channel echo canceller parameters control
Transparent data transfer and mute
Fast reconvergence on echo path changes
Fully programmable conve rgence speeds
Patented Advanced Non-Linear Processo r with
high quality subjective performance
Protection against narrow band signal
divergence and in stability in high echo
environments
+9 dB to -12 dB level adjusters (3 dB steps) at all
signal ports
Offset nulling of all PCM channels
10 MHz or 20 MHz master clock operation
3.3 V pads and 1.8 V Logic core operation with
5 V to le rant in puts
IEEE-1149.1 (JTAG) Test Access Port
Applications
Voice over IP network gateways
Voice over ATM , Frame Relay
T1/E1/J1 multichannel echo cancellatio n
Wireless base stations
Echo Canceller pools
DCME, satellite and multiplexe r system
November 2004
Ordering Information
ZL50232/QCC 100 Pin LQFP Trays
ZL50232/GDC 208 Ball LBGA Tr ays
ZL50232QCC1 100 Pin LQFP* Trays
* Pb Free Matte Tin
-40°C to +85°C
ZL50232
32 Channel Voice Echo Canceller
Data Sheet
Figure 1 - ZL50232 Device Overview
RESET
Rout
IC0
Sout
DS CS R/W A10-A0 DTA D7-D0
Echo Canceller Pool
V
SS
V
DD1 (3.3V)
TDI TDO TCK TRSTTMS
Rin
IRQ
C4i
F0i
MCLK
ODE
Sin
Fsel
Test PortMicroprocesso r Interface
Timing
Unit
Serial
to
Parallel
Parallel
to
Serial
PLL
Group 0
ECA/ECB
Group 4
ECA/ECB
Group 8
ECA/ECB
Group 12
ECA/ECB
Group 1
ECA/ECB
Group 5
ECA/ECB
Group 9
ECA/ECB
Group 13
ECA/ECB
Group 2
ECA/ECB
Group 6
ECA/ECB
Group 10
ECA/ECB
Group 14
ECA/ECB
Group 3
ECA/ECB
Group 7
ECA/ECB
Group 11
ECA/ECB
Group 15
ECA/ECB
Note:
Refer to Fig u re 4
for Echo Canceller
block diagram
V
DD2 (1.8 V)
ZL50232 Data Sheet
2
Zarlink Semiconductor Inc.
Description
The ZL50232 Voice Echo Canceller implement s a cost ef fective s olution for telephony v oice-band echo cancellation
conforming to ITU-T G.168 requirements. The ZL50232 architecture contains 16 groups of two echo cancellers
(ECA and ECB) which can be configured to provide two channels of 64 milliseconds or one channel of 128
milliseconds echo cancellation. This provides 32 channels of 64 milliseconds to 16 channels of 128 milliseconds
echo cancellation or any combination of the two configuration s. The ZL50232 support s ITU-T G.165 an d G.16 4 tone
disable requirements
Figure 2 - 100 Pin LQFP
31
30
50
171197252321193 5 13 151
D7
D6
D5
D4
D3
D2
D1
D0
CS
DS
VSS
NC
R/W
DTA
2 4 6 8 1012141618202224
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
29
28
27
26
51525354555657585960616263646566676869707172737475
100
77
99
76
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
A1
A2
A3
A4
A5
A0
VDD1
VDD2
NC
VSS
A6
A7
A8
A9
A10
VSS
VDD2
VDD1
VSS
VSS
PLLVSS2
NC
ODE
Sout
Rout
Sin
NC
NC
VSS
C4ib
Foib
Rin
VDD2
VDD2
Mclk
fsel
PLLVSS1
PLLVDD
VDD1
TMS
TDI
TDO
TCK
VSS
TRSTB
RESETB
IRQB ZL50232QC
NC
(100 pin LQFP)
VDD1 = 3.3 V VDD2 = 1.8 V
NC
VDD1
VSS
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
IC0
IC0
IC0
IC0
IC0
IC0
IC0
IC0
IC0
IC0
IC0
IC0
IC0
IC0
IC0
NC
ZL50232 Data Sheet
3
Zarlink Semiconductor Inc.
Figure 3 - 208 Ball LBGA
B
C
D
E
F
G
H
J
K
L
M
N
12345678910111213
1
- A1 corner is identified by metallized markings.
A
14 15 16
P
R
T
1
VDD2
c4i
F0i Rin SinRout ODE
A1
Sout
MCLK
Fsel
TMSTDI
TCK
RESET IRQ DS CSR/W DTA
D0 D1 D2 D4 D5 D6 D7
A10
A9
A8
A7
A6
A5
A4
A3
A2
ZL50232GD
VDD1
IC0
PLLVSS PLLVDD
IC0 IC0 IC0
IC0 IC0
IC0 IC0
IC0
IC0 IC0
IC0
IC0
IC0
IC0 VDD1
VSS
NC
NC
TDO TRST
A0
D3
NC NC
NC
NC
NC
NC
NC NC NC
NC
NC
NC
NC
NC
NC
NC
VSS
VSS
VSS
VSS VSS
VSS
VSS VSS
VSS VSS
VSS VSS
VSS VSS VSS VSS
VSS
VSS
VSS
VSS
VSS
VSS VSS VSS VSS
VSS
VSS
VSS
VSS
VSS VSS
VSS
VSS
VSS VSS VSS VSS
VSS
VSS
VSS VSS VSS VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS VSS
VSS
VSS
VSS
VSS VSS VSS
VSS
VSS
VDD1
VDD1 VDD1
VDD1
VDD1
VDD1
VDD1 VDD1
VDD1 VDD1
VDD1
VDD1
VDD1
VDD1
VDD1
VDD1 VDD1
VDD1
VDD1
VDD1 VDD1
VDD1 VDD1
VDD1
VDD1
VDD1
VDD1
VDD1
VDD1
VDD1
VDD1
VDD1
VDD1
VDD1
VDD1 VDD1
VDD1
VDD1
VDD1
VDD2
VDD2 VDD2
VDD2
VDD2
VDD2 VDD2
VSS
VSS VSS VSS VSS
VSS VSS VSS VSS
VSS VSS VSS VSS
VSS VSS VSS VSS
VDD1
ZL50232 Data Sheet
4
Zarlink Semiconductor Inc.
Pin Description
Pin
Name
Pin #
Description
208-Ball LBGA 100 Pin
LQFP
VSS A1, A3,A7,A11, A13,
A15, A16, B2, B6, B8,
B12, B14, B15, B16, C3,
C5, C7, C9, C11, C12,
C13, C14, C16, D4, D8,
D10, D12, D13, E3, E4,
E14, F13, G3, G4, G7,
G8, G9, G10, H7, H8,
H9, H10, H13, H14, J7,
J8, J9, J10, K7, K8, K9,
K10, K13, K14, L3, L4,
M13, M14, M15, N3, N4,
N5, N7, N9, N11, N13,
P2, P3, P5, P7, P9.P11,
P13, P14, R2, R14,
R15, R16, T1, T3, T7,
T10, T14, T16
5, 18, 32,
42, 56, 69,
81, 98
Ground.
VDD1 A5, A9, B10, C4, C8,
B4, C10, D3, D5, D7,
D9, D11, D14, E13, F3,
F4, F14, H3, H4, J13,
J14, L13, L14, M3, M4,
N6, N8, N10, N14, N15,
P4, P6, P8, P10, P15,
R4, R6, R8, R10, R12,
T5, T12
27, 48, 77,
100 Positive Power Supply. Nominally 3.3 V (I/O Voltage).
VDD2 C6, D6, J3, J4, N12,
P12, G13, G14 14, 37, 64,
91 Positive Power Supply. Nominally 1.8 V (Core Voltage).
IC0 E15, F15, A12, A10, A6,
A2, B1, B3, C1, C2, D2,
E2, J2, K2, R1
7, 41, 43,
65, 66, 67,
68, 70, 71,
72, 86, 87,
88, 93, 94
Internal Connection. These pins must be connected to VSS for
normal operation.
NC A14, C15, D1, D15, E1,
F1, G1, G15, H1, H15,
J1, J15, K1,
K15,L1,L15,F2,L2
24, 25, 26,
44, 45, 46,
47, 49, 51,
52, 53, 54,
55, 73, 74,
75, 76, 78,
79, 80, 82,
83, 84, 85,
89, 99, 50
No connection. These pins must be left open for normal
operation.
IRQ R9 9 Interrupt Request (Open Drain Output). This output goes low
when an interrupt occurs in any channel. IRQ returns high when
all the interrupts have been read from the Interrupt FIFO
Register. A pull-up resistor (1 K typical) is required at this output.
ZL50232 Data Sheet
5
Zarlink Semiconductor Inc.
DS R11 10 Dat a Strobe (Input). This active low input works in conjunction
with CS to enable the read and write operations.
CS R13 11 Chip Select (Input). This active low input is used by a
microprocessor to activate the microprocessor port.
R/W R5 12 Read/Write (Input). This input controls the direction of the data
bus lines (D7-D0) during a microprocessor access.
DTA R7 13 Data Transfer Acknowledgment (Open Drain Output). This
active low output indicates that a data bus transfer is completed.
A pull-up resistor (1 K typical) is required at this output.
D0..D7 T2,T4,T6,T8,T9,T11,
T13,T15 15, 16, 17,
19, 20, 21,
22, 23
Data Bus D0 - D7 (Bidirectional). These pins form the 8 bit
bidirectional data bus of the microprocessor port.
A0..A10 P16,N16,M16,L16,K16,
J16,H16,G16,F16,E16,
D16
28, 29, 30,
31, 33, 34,
35, 36, 38,
39, 40
Address A0 to A10 (Input). These inputs provide the A10 - A0
address lines to the internal registers.
ODE B13 57 Output Drive Enable (Input). This input pin is logically AND’d
with the ODE bit-6 of the Main Control Register. When both ODE
bit and ODE input pin are high, the Rout and Sout ST-BUS
outputs are enabled.
When the ODE bit is low or the ODE input pin is low, the Rout
and Sout ST-BUS outputs are high impedance.
Sout A8 58 Send PCM Signal Output (Output). Port 1 TDM data output
streams. Sout pin outputs serial TDM data streams at
2.048 Mbps with 32 channels per stream.
Rout B9 59 Receive PCM Signal Output (Output). Port 2 TDM data output
streams. Rout pin outputs serial TDM data streams at
2.048 Mbps with 32 channels per stream.
Sin B11 60 Send PCM Signal Input (Input). Port 2 TDM data input streams.
Sin pin receives serial TDM data streams at 2.048 Mbps with 32
channels per stream.
Rin B7 61 Receive PCM Signal Input (Input). Port 1 TDM data input
streams. Rin pin receives serial TDM data streams at
2.048 Mbps with 32 channels per stream.
F0i B5 62 Fram e P ulse (Input). This input accepts and auto matically
identifies frame synchronization signals formatted according to
ST-BUS or GCI interfac e sp ec ifications.
C4i A4 63 Serial Clock (Input). 4.096 MHz serial clock for shifting data
in/out on the serial streams (Rin, Sin, Rout, Sout).
MCLK G2 90 Master Clock (Input). Nominal 10 MHz or 20 MHz Master Clock
input. May be connected to an async hronous (relative to frame
signal) clock source.
Pin Description (continued)
Pin
Name
Pin #
Description
208-Ball LBGA 100 Pin
LQFP
ZL50232 Data Sheet
6
Zarlink Semiconductor Inc.
1.0 Device Overview
The ZL50232 architecture cont ains 32 e cho cancellers divide d into 16 group s. Each group has tw o echo cancellers,
Echo Canceller A and Echo Canceller B. Each group can be configured in Normal, Extended Delay or
Back-to-Back configurations. In Norm al configuration, a g roup of echo cancellers pro vides two c hann els of 64 ms
echo cancellation, which run independently on different channels. In Extended Delay configuration, a group of
echo cancellers achieves 128 ms of echo cancellation by cascading the two echo cancellers (A & B). In
Back-to-Back configuration, the two echo cancellers from the same group are positioned to cancel echo coming
from both directions in a single channel, providing full-duplex 64 ms echo cancellation.
Fsel H2 92 Frequency select (Input). This input selects the Master Clock
frequency operation. When Fsel pin is low, nominal 19.2 MHz
Master Clock input must be applied. When Fsel pin is high,
nominal 9.6 MHz Master Clock input must be applied.
PLLVss1
PLLVss2 K3 97, 95 PLL Ground. Must be connected to VSS
PLLVDD K4 96 PLL Power Supply. Must be connected to VDD2 = 1.8 V
TMS M2 1 Test Mode Select (3.3 V Input). JTAG signal that controls the
state transitions of the TAP controller. This pin is pulled high by
an internal pull-up when not driven.
TDI M1 2 Test Serial Data In (3.3 V Input). JTAG serial test instructions
and data are shifted in on this pin. This pin is pulled high by an
internal pull-up when not driven.
TDO N1 3 Test Serial Data Out (Output). JTAG serial data is output on this
pin on the falling edge of TCK. This pin is held in high impeda nce
state when JTAG scan is not enabled.
TCK P1 4 Test Clock (3.3 V Input). Pro vides the clock to the JTAG test
logic.
TRST N2 6 Test Reset (3.3 V Input). Asynchronously initializes the JTAG
TAP controller by putting it in the Test-Logic-Reset state. This pin
should be pulsed low on power-up or held low, to ensure that the
ZL50232 is in the normal functional mode. This pin is pulled by
an internal pull-down when not driven.
RESET R3 8 Device Reset (Schmitt Trigger Input). An active low resets the
device and puts the ZL50 232 into a low-power stand-by mode.
When the RESET pin is re turned to logic high and a clock is
applied to the MCLK pin, the device will automatica lly execute
initialization routines, which preset all the Main Control an d
Status Registers to their default power-up values.
Pin Description (continued)
Pin
Name
Pin #
Description
208-Ball LBGA 100 Pin
LQFP
ZL50232 Data Sheet
7
Zarlink Semiconductor Inc.
Each echo canceller con tains the following main elements (see Figure 4).
Adaptive Filter for estimating the echo channel
Subtractor for cancelling the echo
Double-Talk detec tor for disabling the filt er adaptation during periods of double-talk
Path Change detector for fast reconvergence on major echo path changes
Instability Detector to combat instability in very low ERL environments
Patented Advanced Non-Linear Processo r for suppression of residual echo , with comfort noise inje ction
Disable Tone Detectors for detecting valid disable tones at send and receive path inputs
Narrow-Band Detector for preventing Adaptive Filter diverg ence from narrow-band sig nals
Offset Null filters for removing the DC component in PCM channels
+9 to -12 dB level adju sters at all signal ports
Parallel con troller interfa ce compatible with Motorola microcontrollers
PCM encoder/decoder compatible with µ/A-Law ITU-T G.711 or Sign-Magnitud e coding
Each echo canceller in the ZL50232 has four functional states: Mute, Bypass, Disable Adaptation and Enable
Adaptation. These are explained in the section entitled Echo Can celler Functional States.
Figure 4 - Functional Block Diagram
1.1 Adaptive Filter
The adaptive filter a dapts to the e cho path and generates an estimate of th e echo signal. This echo estimate is then
subtracted from Sin. For each group of echo cancellers, the adaptive filter is a 1024 tap FIR adaptive filter which is
divided into two sections. Each section contains 512 taps providing 64 ms of echo estimation. In Normal
configuration, the first section is dedicated to channel A and the second section to channel B. In Extended Delay
configuration, both sections are cascaded to provide 128 ms of echo estimation in channel A. In Back-to Back
configuration, the first section is used in the receive direction and the second section is used in the transmit
direction for the same channel.
Σ
Non-Linear
Processor
Offset
Null Linear/
µ
/A-Law
Microprocessor
Interface
Double - Talk
Detector
Control
Narrow-Band
Detector
µ
/A-Law/
Linear
Offset
Null
Echo Canceller (N), where 0 < N < 31
Sout
Rin
Sin
Rout
-
Programmable Bypass
(channel N)
(channel N)
(channel N)
(channel N)
ST-BUS
ST-BUS
PORT2 PORT1
MuteR
MuteS
+9 to -12 dB
Level Adjust
Linear/
µ
/A-Law +9 to -12 dB
Level Adjust
+9 to -12 dB
Level Adjust
µ
/A-Law/
Linear +9 to -12 dB
Level Adjust
Adaptive
Filter
Disable Tone
Detector
Disabl e To ne
Detector
Detector
Path Change
Instability
Detector
ZL50232 Data Sheet
8
Zarlink Semiconductor Inc.
1.2 Double-Talk Detecto r
Double-Talk is defined as those periods of time when signal energy is present in both directions simultaneously.
When this happens, it is necessary to disable the filter adaptation to prevent divergence of the Adaptive Filter
coefficients. Note that when double-talk is detected, the adaptation process is halted but the echo canceller
continues to cancel echo using the previous converged echo profile. A double-talk condition exists whenever the
relative signal levels of Rin (Lrin) and Sin (Lsin) meet the following condition:
Lsin > Lrin + 20log10(DTDT)
where DTDT is the Double-Talk Detection Threshold. Lsin and Lrin are signal levels expressed in dBm0.
A different method is used when it is uncertain whether Sin consists of a low level double-talk signal or an echo
return. During these periods, the adaptation process is slowed down but it is not halted. The slow convergence
speed is set using the Slow sub-register in Control Register 4. During slow convergence, the adaptation speed is
reduced by a factor of 2Slow relative to normal convergence for non-zero values of Slow. If Slow equals zero,
adaptation is halted completely.
In the G.168 standard, the echo return loss is expected to be at least 6 dB. This implies that the Double-Talk
Detector Threshold (DTDT) should be set to 0.5 (-6 dB). However, in order to achieve additional guardband, the
DTDT is set internally to 0.5625 (-5 dB).
In some applications the return loss can be higher or lower than 6 dB. The ZL50232 allows the user to change the
detection threshold to suit each application’s need. This threshold can be set by writing the desired threshold value
into the DTDT register.
The DTDT register is 16 bits wide. The register value in hexadecimal can be calculated with the following equation:
DTDT(hex) = hex(DTDT(dec) * 32768)
where 0 < DTDT(dec) < 1
Example:For DTDT = 0.562 5 (-5 d B), the
hexadecimal value becomes
hex(0.5625 * 32768) = 4800hex
1.3 Path Change Detector
Integrated into the ZL50232 is a Path Change Detector. This permits fast reconvergence when a major change
occurs in the echo channel. Subtle changes in the echo channel are also tracked automatically once convergence
is achieved, but at a much slower speed.
The Path Change Detector is activated by setting the PathDet bit in Control Register 3 to “1”. An optional path
clearing feature can be enabled by setting the PathClr bit in Control Register 3 to “1”. With path clearing turned on,
the existing echo channel estimate will also be cleared (i.e. the adaptive filter will be filled with zeroes) upon
detection of a major p ath change.
ZL50232 Data Sheet
9
Zarlink Semiconductor Inc.
1.4 Non-Linear Processor (NLP)
After echo cancellation, there is always a small amount of residual echo which may still be audible. The ZL50232
uses Zarlink’s patented Advanced NLP to remove residual echo signals which have a level lower than the
Adaptive Suppression Threshold (TSUP in G.168). This threshold depends upon the level of the Rin (Lrin)
reference signal as well as the programmed value of the Non-Linear Processor Threshold register (NLPTHR).
TSUP can be calculated by the following equation:
TSUP = Lrin + 20log10(NLPTHR)
where NLP THR is the N on-Linear Pro cessor Threshold register value and Lrin is the relative pow er level expressed
in dBm0. The NLPTHR register is 16 bits wide. The register value in hexadecimal can be calculated with the
following equation:
NLPTHR(hex) = hex(NLPTHR(dec) * 32768)
where 0 < NLPTHR(dec) < 1
When the level of residual error signal falls below TSUP, the NLP is activated further attenuating the residual signal
by an additional 30 dB. To prevent a perceived decrease in background noise due to the activation of the NLP, a
spectrally-shaped comfort noise, equivalent in power level to the background noise, is injected. This keeps the
perceived noise level constant. Consequently, the user does not hear the activation and de-activa tion of the NLP.
The NLP processor can be disabled by setting the NLPDis bit to “1” in Control Register 2.
The comfort noise injector can be disabled by setting the INJDis bit to “1” in Control Register 1. It should be noted
that the NLPTHR is valid and the comfort noise injection is active only when the NLP is enabled.
The patented Advanced NLP provides a number of new and improved features over the original NLP found in
previous generation devices. Differences between the Advanced NLP and the original NLP are summarized in
Table 1.
The NLPSel bit in Control Register 3 selects which NLP is used. A “1” will select the Advanced NL P, “0 selects the
original NLP.
Feature Register or Bit(s) Advanced
NLP Default
Value
Original NLP
Default Value
NLP Selection NLPSel (Control Register 3) 1 0 (feature
not supported)
Reject uncanceled echo as noise NLRun1 (Control Register 3) 1 0 (feature
not supported)
Reject double-talk as noise NLRun2 (Control Register 3) 1 0 (feature
not supported)
Noise level estimate or ramping
scheme InjCtrl (Control Register 3) 1 0 (feature
not supported)
Noise level ramping rate NLInc (Noise Control) 5(hex) C(hex)
Noise level scaling Noise Scaling 16(hex) 74(hex)
Table 1 - Comparison of NLP Types
ZL50232 Data Sheet
10
Zarlink Semiconductor Inc.
The Advanced NLP uses a new noise ramping scheme to quickly and more accurately estimate the background
noise level. The noise ramping method of the original NLP can also be used. The InjCtrl bit in Control Register 3
selects the ramping scheme.
The NLInc sub-register in Noise Control is used to set the ramping speed. When InjCtrl = 1 (such as with the
Advanced NLP), a lower value will give faster ramping. When InjCtrl = 0 (such as with the original NLP), a higher
value will give faster ramping. NLInc is a 4-bit value, so only values from 0 to F(hex) are valid.
The Noise Scaling register can be used to adjust the relative volume of the comfort noise. Lowering this value will
scale the injected noise level down, convers ely, raising the value will scale the comfort noise up. Due to difference s
in the noise estimator operation, the Advanced NLP requires a diff erent scaling value than the original NLP.
IMPORTANT NOTE: NLInc and the Noise Scaling register have been pre-programmed with G.168 compliant
values. Changing these values may re sult in undesirable comfort noise performance!
The Advanced NLP also contains safeguards to prevent double-talk and uncancelled echo from being mistaken for
background noise. These features were not present in the original NLP. They can be disabled by setting the
NLRun1 and NLRun2 bit s in Control Register 3 to “0”.
1.5 Disable Tone Det ector
The G.165 recommendation defines the disable tone as havin g the following characteris tics: 210 0 Hz ( ±21 Hz) sine
wave, a power level between -6 to -31 dBm0, and a phase reversal of 180 degrees (± 25 degrees) every
450 ms (±25 ms). If the disable tone is present for a minimum of one second with at least one phase reversal, the
Tone Detector will trigger.
The G.164 recommendation defines the disable tone as a 2100 Hz (+21 Hz) sine wave with a power level between
0 to -31 dBm0. If the disable tone is present for a minimum of 400 ms, with or without phase reversal, the Tone
Detector will trigger.
The ZL50232 has two Tone Detectors per channels (for a total of 64) in order to monitor the occurrence of a valid
disable tone on both Rin and Sin. Upon detection of a disable tone, TD bit of the Status Register will indicate logic
high and an interrupt is generated (i.e. IRQ pin low). Refer to Figure 5 and to the Interrupts section.
Figure 5 - Disable Tone Detection
Once a Tone Detector has been triggered, there is no longer a need for a valid disable tone (G.164 or G.165) to
maintain Tone Detector status (i.e. TD bit high). The Tone Detector status will only release (i.e. TD bit low) if the
signals Rin and Sin fall below -30 dBm0, in the frequency range of 390 Hz to 700 Hz, and below -34 dBm0, in the
frequency range of 700 Hz to 3400 Hz, for at least 400 ms. Whenever a Tone Detector releases, an interrupt is
generated (i.e. IRQ pin low).
The selection between G.165 and G.164 tone disable is controlled by the PHDis bit in Control Register 2 on a per
channel basis. When the PHDis bit is set to “1”, G.164 tone disable requirements are selected.
TD bit
Rin
Sin
Echo Canceller A
Tone Detector
Tone Detector Status reg
ECA
TD bit
Rin
Sin
Echo Canceller B
Tone Detector
Tone Detector Status reg
ECB
ZL50232 Data Sheet
11
Zarlink Semiconductor Inc.
In response to a valid disable tone, the echo canceller must be switched from the Enable Adaptation state to the
Bypass state. This can be done in two ways, automatically or externally. In automatic mode, the Tone Detectors
internally control the switching between Enable Adaptation and Bypass states. The automatic mode is activated by
setting the AutoTD bit in Control Register 2 to high. In ex ternal mod e, an exte rnal controller is needed to service the
interrupts and poll the TD bits in the Status Registers. Following the detection of a disable tone (TD bit high) on a
given channel, the external controller must switch the echo cance ller from Enable Ada ptation to Bypass state.
1.6 Instability Detector
In systems with very low echo channel return loss (ERL), there may be enough feedback in the loop to cause
stability problems in the adaptive filter. This instability can result in variable pitched ringing or oscillation. Should this
ringing occur, the Instability Detector will activate and suppress the oscillations.
The Instability Detector is activated by setting the RingClr bit in Control Register 3 to “1”.
1.7 Narrow Band Signal Detector (NBSD)
Single or dual frequency tones (i.e. DTMF tones) present in the receive input (Rin) of the echo canceller for a
prolonged period of time may cause the Adaptive Filter to diverge. The Narrow Band Signal Detector (NBSD) is
designed to prevent this by detecting single or dual tones of arbitrary frequency, phase, and amplitude. When
narrow band signals are detected, adaptation is halted but the echo can celler continues to cancel echo.
The NBSD will be active regardless of the Echo Canceller functional state. However the NBSD can be disabled by
setting the NB Dis bit to “1” in Control Register 2.
1.8 Offset Null Filter
Adaptive filters in general do not operate properly when a DC offset is present at any input. To remove the DC
component, the ZL50232 incorporates Offs et Null filters in both Rin and Sin inputs.
The offset null filters can be disabled by setting the HPFDis bit to “1” in Control Register 2.
1.9 Adjustable Level Pads
The ZL50232 provides adjustable level pads at Rin, Rout, Sin and Sout. This setup allows signal strength to be
adjusted both inside and outside the echo path. Each signal level may be independently scale d with anywhere from
+9 dB to -12 dB level, in 3 dB steps. Level values are set using the Gains register.
CAUTION: Gain adjustment can help interface the ZL502 32 to a particular sys tem in order to provide optimum echo
cancellation, but it can also degrade performance if not done carefully. Excessive loss may cause low signal levels
and slow convergence. Exercise great care when adjusting these values. Also, due to internal signal routings in
Back to Back mode, it is not recommended that gain adjustments be used on Rin or Sout in this mode.
The -12 dB PAD bit in Control Register 1 is still supported as a legacy feature. Setting this bit will provide 12 dB of
attenuation at Rin, and override the values in the Gains register.
1.10 ITU-T G.168 Compliance
The ZL50232 has been certified G.168 (1997), (2000) and (2002) compliant in all 64 ms cancellation modes
(i.e. Normal and Back-to-Back configurations) by in-house testing with the DSPG ECT-1 echo canceller tester.
The ZL50232 has also been tested for G.168 compliance and all voice quality tests at AT&T Labs. The ZL50232
was classified as “carrier grade” echo canceller.
ZL50232 Data Sheet
12
Zarlink Semiconductor Inc.
2.0 Device Configuration
The ZL50232 architec ture contains 32 echo cancellers divided into 16 groups. Each group has two echo cancellers
which can be individually controlled (Echo Canceller A (ECA) and Echo Canceller B (ECB)). They can be set in
three distinct configurations: Normal, Back-to-Back, and Extended Delay. See Figures 6, 7, and 8.
2.1 Normal Configuration
In Normal configuration, the two echo cancellers (Echo Canceller A and B) are positioned in parallel, as shown in
Figure 6, providing 64 milliseconds of echo cancellation in two channels simultaneously.
Figure 6 - Normal Device Configuration (64 ms)
2.2 Back-to-Back Config uration
In Back-to-Back configuration, the two echo cancellers from the same group are positioned to cancel echo coming
from both directions in a single channel providing full-duplex 64 ms echo cancellation. See Figure 7. This
configuration uses only one timeslot on PORT1 and PORT2 and the second timeslot normally associated with ECB
contains zero code. Back-to-Back configuration allows a no-glue interface for applications where bidirectional echo
cancellation is required.
Figure 7 - Back-to-Back Device Configuration (64 ms)
Rin
Rout
Sout
Sin
echo
path A
echo
path B
+
-
channel A
channel A
+
-
channel B
channel B
ECA
ECB
Adaptive
Filter (64 ms)
Adaptive
Filter (64 ms)
PORT1PORT2
+
ECA
Sin Sout
Rout Rin
-
ECB
+-
echo echo
path path
Adaptive
Filter (64 ms)
Adaptive
Filter (64 ms)
PORT1PORT2
ZL50232 Data Sheet
13
Zarlink Semiconductor Inc.
Back-to-Back configuration is selected by writing a “1” into the BBM bit of Control Register 1 for both Echo
Canceller A and Echo Canceller B for a given group of echo canceller. Table 4 shows the 16 groups of 2 cancellers
that can be configured into Back-to-Back.
Examples of Back-to-Back configuration include positioning one group of echo cancellers between a codec and a
transmission device or between two codecs for echo control on analog trunks.
2.3 Extended Delay Configuration
In this configuration, the two echo cancellers from the same group are internally cascaded into one 128
milliseconds echo canceller. See Figure 8. This configuration uses only one timeslot on PORT1 and PORT2 and
the second timeslot normally associated with ECB contains quiet code.
Figure 8 - Extended Delay Configuration (128 ms)
Extended Delay configuration is selected by writing a “1” into the ExtDl bit in Echo Canceller A, Control Register 1.
For a given group, only Echo Canceller A, Control Register 1, has the ExtDl bit. For Echo Canceller B Control
Register 1, Bit 0 must always be set to zero.
Table 4 shows the 16 groups of 2 cancellers that can each be configured into 64 ms or 128 ms echo tail capacity.
3.0 Echo Canceller Functional States
Each echo canceller has four functional states: Mute, Bypass, Disable Adaptation and Enable Adapt ation.
3.1 Mute
In Normal and in Extended Delay configurations, writing a “1” into the MuteR bit replaces Rin with quie t code which
is applied to both the Adaptive Filter and Rout. Writing a “1” into the MuteS bit replaces the Sout PCM data with
quiet code.
LINEAR
16 bits
2’s
complement
SIGN/
MAGNITUDE
µ-Law
A-Law
CCITT (G.711)
µ-Law A-Law
+Zero
(quiet code) 0000hex 80hex FFhex D5hex
Table 2 - Quiet PCM Code Assignment
+
-
channel A
channel A
ECA
Sin Sout
Rout Rin
echo
path A Adaptive Filter
(128 ms)
PORT1PORT2
ZL50232 Data Sheet
14
Zarlink Semiconductor Inc.
I n B a ck - t o- B ac k c on f iguration, w r i ti n g a 1” i nt o t he M ut e R bit of Echo Canceller A, Control Register 2, causes
quiet code to be transmitted on Rout. Writing a 1 into the MuteS bit of Echo Canceller A, Control Register 2,
causes quiet code to be transmitted on Sout.
In Extended Delay and in Back-to-Back configurations, MuteR and Mu teS bit s of Echo Canceller B must always be
0”. Refer to Figure 4 and to Control Register 2 for bit description.
3.2 Bypass
The Bypass state directly transfers PCM codes from Rin to Rout and from Sin to Sout. When Bypass state is
selected, the Adaptive Filter coefficie nt s a re reset to zero. Byp ass st ate mu st be selected for at lea st one frame
(125 µs) in order to properly clear the filter.
3.3 Disable Adaptation
When the Disable Adaptation state is selected, the Adaptive Filter coefficients are frozen at their current value. The
adaptation process is halted, however, the echo canceller continues to cancel ec ho.
3.4 Enable Adaptation
In Enable Adaptation state, the Adaptive Filter coefficients are continually updated. This allows the echo canceller
to model the echo return path characteristics in order to cancel echo. This is the normal operating state.
The echo canceller functions are selected in Control Register 1 and Control Register 2 through four control bits:
MuteS, MuteR, Bypas s and AdaptDis. Refer to the Registers Description for details.
4.0 ZL50232 Throughput Delay
The throughput delay of the ZL50232 varies according to the d evice configura tion. For all device configurations , Rin
to Rout has a delay of two frames and Sin to Sout has a delay of three frames. In Bypass st ate, the Rin to Rout and
Sin to Sout paths have a delay of two frames.
5.0 Serial PCM I/O channels
There are two sets of TDM I/O streams, each with channels numbered from 0 to 31. One set of input streams is for
Receive (Rin) channels, and the other set of input streams is for Send (Sin) channels. Likewise, one set of output
streams is for Rout PCM channels, and the other se t is for Sout channels. See Figure 9 for channel allocation.
The arrangement and connection of PCM channels to each echo canceller is a 2 port I/O configu ration for eac h set
of PCM Send and Receive channels, as illustrated in Figure 4.
5.1 Serial Data Interface Timing
The ZL50232 provides ST-BUS and GCI interface timing. The Serial Interface clock frequency, C4i, is 4.096 MHz.
The input and output data rate of the ST-BUS and GCI bus is 2.048 Mbps.
The 8 KHz input frame pulse can be in either ST-BUS or GCI format. The ZL50232 automatically detects the
presence of an input frame pulse and ident ifi es i t as eit her ST-BUS or GCI. In ST-BUS format, every second falling
edge of the C4i clock marks a bit boundary, and the data is clocked in on the rising edge of C4i, three quarters of
the way into the bit cell (See Figure 12). In GCI format, every second rising edge of the C4i clock marks the bit
boundary, and data is clocked in on the second falling edge of C4i, half the way into the bit cell (see Figure 13).
ZL50232 Data Sheet
15
Zarlink Semiconductor Inc.
Figure 9 - ST-BUS and GCI Interface Channel Assignment for 2 Mbps Data Streams
Base
Address + Echo Canceller A Base
Address + Echo Canceller B
MS
Byte LS
Byte MS
Byte LS
Byte
- 00h Control Reg 1 - 20h Control Reg 1
- 01h Control Reg 2 - 21h Control Reg 2
- 02h Status Reg - 22h Status Reg
- 03h Reserved - 23h Reserved
- 04h Flat Delay Reg - 24h Flat Delay Reg
- 05h Reserved - 25h Reserved
- 06h Decay Step Size Reg - 26h Decay Step Size Reg
- 07h Decay Step Number - 27h Decay Step Number
- 08h Control Reg 3 - 28h Control Reg 3
- 09h Control Reg 4 - 29h Control Reg 4
- 0Ah Noise Scaling - 2Ah Noise Scaling
- 0Bh Noise Contro l - 2Bh Noise Control
0Dh 0Ch Rin Peak Detect Reg 2Dh 2Ch Rin Peak Detect Reg
0Fh 0Eh Sin Peak Detect Reg 2Fh 2Eh Sin Peak Detect Reg
11h 10h Error Peak Detect Reg 31h 30h Error Peak Detect Reg
13h 12h Reserved 33h 32h Reserved
15h 14h DTDT Reg 35h 34h DTDT Reg
17h 16h Reserved 37h 36h Reserved
19h 18h NLPTHR 39h 38h NLPTHR
1Bh 1Ah Step Size, MU 3Bh 3Ah Step Size, MU
1Dh 1Ch Gains 3Dh 3Ch Gains
1Fh 1Eh Reserved 3Fh 3Eh Reserved
Table 3 - Memory Mapping of Per Channel Control and Status Registers
F0i
Rin/Sin
Rout/Sout Channel 31Channel 0
125 µsec
Channel 1 Channel 30
ST-BUS
F0i
GCI interface
Note: Refer to Figure 12 and Figure 13 for timing details.
ZL50232 Data Sheet
16
Zarlink Semiconductor Inc.
6.0 Memory Mapped Control and Status Registers
Internal memory and registers are memory mapped into the address sp ace of the HOST interface. The internal dual
ported memory is mapped into segments on a “per channel” basis to monitor and control each individual echo
canceller and associated PCM channels. For example, in Normal configuration, echo canceller #5 makes use of
Echo Canceller B from group 2. It occupies the internal address space from 0A0hex to 0BFhex and interfaces to
PCM channel #5 on all serial PCM I/O streams.
As illustrated in Table 3, the “per channel” registers provide independent control and status bits for each echo
canceller. Figure 10 shows the memory map of the control/status register blocks for all echo cancellers.
When Extended Delay or Back-to-Back configuration is selected, Con trol Register 1 of ECA and ECB and Control
Register 2 of the selected group of echo cancellers require special care. Refer to the Register description section.
Table 4 is a list of the channels used for the 16 groups of echo cancellers when they are configured as Extended
Delay or Back-to-Back.
6.1 Normal Configuration
For a given group (group 0 to 15), 2 PCM I/O channels are used. For example, group 1 Echo Cancellers A and B,
channels 2 and 3 are active.
6.2 Extended Delay Configuration
For a given group (group 0 to 15), only one PCM I/O channel is active (Echo Canceller A) and the other channel
carries quiet code. For example, group 2, Echo Canceller A (Channel 4) will be active and Echo Canceller B
(Channel 5) will carry quiet code.
Group Channels Group Channels
00, 1816, 17
12, 3918, 19
2 4, 5 10 20, 21
3 6, 7 11 22, 23
4 8, 9 12 24, 25
5 10, 11 13 26, 27
6 12, 13 14 28, 29
7 14, 15 15 30, 31
Table 4 - Group and Channel Allocation
ZL50232 Data Sheet
17
Zarlink Semiconductor Inc.
6.3 Back-to-Back Config uration
For a given group (group 0 to 15), only one PCM I/O channel is active (Echo Canceller A) and the other channel
carries quiet code. For example, group 5, Echo Canceller A (Channel 10) will be active and Echo Canceller B
(Channel 11) will carry quiet code.
Figure 10 - Memory Mapping
6.4 Power Up Sequence
On power up, the RESET pin must be held low for 100 µs . Forcing the RESET pin low will put the ZL50232 in power
down state. In this state, all internal clocks are halted, D<7:0>, Sout, Rout, DTA and IRQ pins are tristated. The 16
Main Control Registers, the Interrupt FIFO Register and the Test Register are reset to zero.
When the RESET pin returns to logic high and a valid MCLK is applied, the user must wait 500 µs for the PLL to
lock. C4i and F0i can be active during this period. At this point, the echo canceller must have the internal registers
reset to an initial state. This is accomplished by one of two methods. The user can either issue a second hardware
reset or perform a software reset. A second hardware reset is performed by driving the RESET pin low for at least
500 ns and no more than 1500 ns before being released. A sof tware reset is acc omplished by programming a “1” to
each of the PWUP bits in the Main Control Registers, waiting 250 µs (2 frames) and then programming a “0” to
each of the PWUP bits.
The user must then wait 500 µs for the PLL to relock. Once the PLL has locked, the user can power up the 16
groups of echo cancellers individually by writing a “1” into the PWUP bit in Main Control Register of each echo
canceller group.
For each group of echo cancellers, when the PWUP bit toggles from zero to one, echo cancellers A and B execute
their initialization routine. The initialization routine sets their registers, Base Address+00hex to Base Address+3 Fhex,
to the default Reset Value and clears the Adaptive Filter coe fficients. Two frames are necessary for the initialization
routine to execute properly.
Once the initialization routine is executed, the us er c an set the per channel Co ntrol Reg isters, Ba se Address+00hex
to Base Address+3Fhex, for the specific application.
0000h -->
Channel 0, ECA C trl/Stat Registers 001Fh
0020h -->
Channel 1, ECB C trl/Stat Registers 003Fh
0040h -->
Channel 2, ECA C trl/Stat Registers 005Fh
0060h -->
Channel 3, ECB C trl/Stat Registers 007Fh
03C0h -->
Channel 30, ECA Ctrl/Stat Registers 03DFh
03E0h -->
Channel 31, ECB Ctrl/Stat Registers 03FFh
0400h --> 040Fh
Main Control Registers <15:0>
Group 0
Echo
Cancellers
Registers
Groups 2 --> 14
Echo Cancellers
Registers
Group 1
Echo
Cancellers
Registers
Group 15
Echo
Cancellers
Registers
0410h
Interrupt FIFO Register
0411h
Test Register
0412h ---> FFFFh
Reserved Te st Register
ZL50232 Data Sheet
18
Zarlink Semiconductor Inc.
Figure 11 - Power Up Sequence Flow Diagram
6.5 Power Management
Each group of echo cancellers can be placed in Power Down mode by writing a “0” into the PWUP bit in their
respective Main Control Register. When a given group is in Power Down mode, the corresponding PCM data are
bypassed from Rin to Rout and from Sin to Sout with two frames delay. Refer to the Main Control Register section
for description.
The typical power consumption can be calculated with the following equation:
PC = 9 * Nb_of_groups + 3.6, in mW
where 0 Nb_of_groups 16.
6.6 Call Initialization
To ensure fast initial convergence on a new call, it is important to clear the Adaptive Filter. This is done by putting
the echo canceller in bypass mode for at least one frame (125 µs) and then enabling adaptation.
Since the Narrow Band De tector is “ON” regardless o f the functiona l st ate of Echo Can celler it is recommended that
the Echo cancellers are reset before any call progress tones are applied.
System Powerup
Delay 100µs
Reset Held Low
Reset High
MCLK Active
Delay 500µs
Reg. Reset Software
Hardware
Reset Low
Delay 1000 ns
Reset High
PWUP to “1”
Delay 250µs
PWUP to “0”
Delay 500µs
ECAN Ready
ZL50232 Data Sheet
19
Zarlink Semiconductor Inc.
6.7 Interrupts
The ZL50232 provides an interrupt pin (IRQ) to indicate to the HOST processor when a G.164 or G.165 Tone
Disable is detected and released.
Although the ZL50232 may be configured to react automatically to tone disable status on any input PCM voice
channels, the user may want for the external HOST processor to respond to Tone Disable information in an
appropriate application-specific manner.
Each echo canceller will generate an interrupt when a Tone Disable occurs and will generate another interrupt
when a Tone Disable releases.
Upon receiving an IRQ, the HOST CPU should read the Interrupt FIFO Register. This register is a FIFO memory
containing the channel number of the echo canceller that has generated the interrupt.
All pending interrupts from any of the echo cancellers and their associated input channel number are stored in this
FIFO memory. The IRQ always returns high after a read access to the Interrupt FIFO Register. The IRQ pin will
toggle low for each pending interrupt.
After the HOST CPU has received the channel number of the interrupt source, the corresponding per channel
Status Register can be read from internal memory to determine the cause of the interrupt (see Table 3 for address
mapping of Status register). The TD bit indicates the presence of a Tone Disable.
The MIRQ bit 5 in the Main Control Register 0 masks interrupts from the ZL50232. To provide more flexibility, the
MTDBI (bit-4) and MTDAI (bit-3) bits in the Main Control Register<15:0> allow Tone Disable to be masked or
unmasked from generating an interrupt on a per channel basis. Refer to the Registers Description section.
7.0 JTAG Support
The ZL50232 JTAG interface conforms to the Boundary-Scan standard IEEE1149.1. This standard specifies a
design-for-testability technique called Boundary-Scan test (BST). The operation of the Boundary Scan circuitry is
controlled by an Test Access Port (TAP) controller. JTAG inputs are 3.3 V compliant only.
7.1 Test Access Po rt (TAP)
The TAP provides access to many test functions of the ZL50232. It consists of four input pins and one output pin.
The following pins are found on the TAP.
Test Clock Input (TCK)
The TCK provides the clock for the test logic. The TC K does not interfere with any on-chip clock and thus
remains independent. The TCK permits shifting of test data into or out of the Boundary-Scan register cells
concurrent with the operation of the device and without interfering with th e on-chip logic.
Test Mode Select Input (TMS)
The logic signals received at the TMS inp ut are interpreted by the TAP Controller to control the test o perations.
The TMS signals are sampled at the rising edge of the TCK puls e. This pin is internally pulled to V DD1 w hen it is
not driven from an external source.
Test Data Input (TDI)
Serial input data applied to this port is fed either into the instruction register or into a test data register,
depending on the sequence previously applied to the TMS input. Both registers are described in a subsequent
section. The received input data is sampled at the rising edge of TCK pulses. This pin is internally pulled to
VDD1 when it is not driven fro m an external source.
Test Data Output (TDO)
Depending on the sequence previously applied to the TMS input, the contents of either the instruction register
or data register are serially shifted out towards the TDO. The data from the TDO is clocked on the falling edge
of the TCK pulses. When no data is shifted through the Boundary Scan cells, the TDO driver is set to a high
impedance state.
ZL50232 Data Sheet
20
Zarlink Semiconductor Inc.
Test Reset (TRST)
This pin is used to reset the JTAG scan structure. This pin is inte rnally pulled to VSS.
7.2 Instruction Register
In accordance with the IEEE 1149.1 st and ard, the ZL50 232 uses public instruction s. The JTAG Interface contains a
3-bit instruction register. Instructions are serially loaded into the instruction register from the TDI when the TAP
Controller is in its shifted-IR state. Subsequently, the instructions are decoded to achieve two basic functions: to
select the test data register th at will operate while the instruction is curren t, and to define the serial test dat a register
path, which is used to shift data between TDI and TDO during data register sca nning.
7.3 Test Data Registers
As specified in IEEE 1149.1, the ZL50232 JTAG Interface contains three test data registers:
Boundary-Scan register
The Boundary-Scan register consists of a series of Boundary-Scan cells arranged to form a scan path around
the boundary of the ZL50232 core logic.
Bypass Register
The Bypass register is a single stage shift register that provides a one-bit path from TDI to TDO.
Device Identification register
The Device Identification register provide s acc ess to the following encoded information:
device version number, part number and manufacturer's name.
* Exceeding these values may cau se permanent damag e. Functional operation under these conditions is not implied.
.
Typical figures are at 25°C and are for design aid only: not guaranteed and not subject to production testing.
Absolute Maximum Ratings*
Parameter Symbol Min. Max. Units
1 I/O Supply Voltage (VDD1)V
DD_IO -0.5 5.0 V
2 Core Supply Voltage (VDD2)V
DD_CORE -0.5 2.5 V
3 Input Voltage VI3 VSS - 0.5 VDD1+0.5 V
4 Input Voltage on any 5 V Tolerant I/O pins VI5 VSS - 0.3 7.0 V
5 Continuous Current at digital outputs Io20 mA
6 Package power dissipation PD2W
7 Storage temperature TS-55 150 °C
Recommended Operating Conditions - Voltages are with respect to ground (Vss) unless otherwise stated
Characteristics Sym. Min, Typ.Max. Units
1 Operating Temperature TOP -40 +85 °C
2 I/O Supply Voltage (VDD_IO)V
DD1 3.0 3.3 3.6 V
3 Core Supply Voltage (VDD_CORE)V
DD2 1.6 1.8 2.0 V
4 Input High Voltage on 3.3 V tolerant I/O VIH3 0.7VDD1 VDD1 V
5 Input High Voltage on 5 V tolerant I/O pins VIH5 0.7VDD1 5.5 V
6 Input Low Voltage VIL 0.3VDD1 V
ZL50232 Data Sheet
21
Zarlink Semiconductor Inc.
Characteristics are over re commended operating conditions unless otherwise stated.
Typical figures are at 25°C, VDD1 =3.3 V and are for design aid only: not guaranteed and not subject to production testing.
* Note 1: Maximum leakage on pins (out put or I/O pins in high impedance state) is over an applied voltage (VIN).
Characteristics are over re commended operating conditions unless otherwise stated.
DC Electrical Characteristics - Voltages are with respect to ground (Vss) unless otherwise stated.
Characteristics Sym. Min. Typ.Max. Units Test Conditions
1
I
N
P
U
T
S
Static Supply Current ICC 250 µA RESET = 0
IDD_IO (VDD1 = 3.3 V) IDD_IO 10 mA All 32 channels active
IDD_CORE (VDD2 = 1.8 V) IDD_CORE 65 mA All 32 channels active
2 Power Consumption PC150 mW All 32 channels active
3 Input High Voltage VIH 0.7VDD1 V
4 Input Low Voltage VIL 0.3VDD1 V
5 Input Leakage
Input Leakage on Pullup
Input Leakage on Pulldown
IIH/IIL
ILU
ILD
-30
30
10
-55
65
µA
µA
µA
VIN=VSS to VDD1or 5.5 V
VIN=VSS
VIN=VDD1
See Note 1
6 Input Pin Capacitance CI10 pF
7O
U
T
P
U
T
S
Output High Voltage VOH 0.8VDD1 VI
OH = 12 mA
8 Output Low Voltage VOL 0.4 V IOL = 12 mA
9 High Impedance Leakage IOZ 10 µAV
IN=VSS to 5.5 V
10 Output Pin Capa citance CO10 pF
AC Electrical Characteristics - Timing Parameter Measurement Voltage Levels
- Voltages are with respect to ground (Vss) unless otherwise stated.
Characteristics Sym. Level Units Conditions
1 CMOS Threshold VTT 0.5VDD1 V
2 CMOS Rise/Fall Threshold Voltage High VHM 0.7VDD1 V
3 CMOS Rise/Fall Threshold Voltage Low VLM 0.3VDD1 V
ZL50232 Data Sheet
22
Zarlink Semiconductor Inc.
Characteristics are over re commended operating conditions unless otherwise stated.
Typical figures are at 25°C, VDD1 = 3.3 V and for desi gn aid only: not guaranteed and not subject to production testing.
Characteristics are over re commended operating conditions unless otherwise stated.
Typical figures are at 25°C, VDD1 = 3.3 V and for desi gn aid only: not guaranteed and not subject to production testing.
* Note1: High Impedance is measured by pulling to the appropriate rail with RL, with timing corrected to cancel time taken to discharge CL.
Characteristics are over re commended operating conditions unless otherwise stated.
Typical figures are at 25°C, VDD1 = 3.3 V and for design aid only: not guaranteed and not subject to production testing.
AC Electrical Characteristics - Frame Pulse and C4i
Characteristic Sym. Min. Typ.Max. Units Notes
1 Frame pulse width (ST-BUS, GCI) tFPW 20 2*
tCP-20 ns
2 Frame Pulse Setup time before
C4i falling (ST-BUS or GCI) tFPS 10 122 150 ns
3Frame Pulse Hold Time from C4i
falling (ST-BUS or GCI) tFPH 10 122 150 ns
4C4i Period tCP 190 244 300 ns
5C4i Pulse Width High tCH 85 150 ns
6C4i Pulse Width Low tCL 85 150 ns
7C4i Rise/Fall Time tr, tf10 ns
AC Electrical Characteristics - Serial Streams for ST-BUS and GCI Backplanes
Characteristic Sym. Min. Typ.Max. Units Test Conditions
1 Rin/Sin Set-up Time tSIS 10 ns
2 Rin/Sin Hold Time tSIH 10 ns
3 Rout/Sout Delay
- Active to Acti ve tSOD 60 ns CL=150 pF
4 Output Data Enable (ODE)
Delay tODE 30 ns CL=150 pF, RL=1 K
See Note 1
AC Electrical Characteristics - Master Clock - Voltages are with respect to ground (VSS). unless otherwise stated.
Characteristic Sym. Min. Typ.Max. Units Notes
1 Master Clock Frequency,
- Fsel = 0
- Fsel = 1 fMCF0
fMCF1 19.0
9.5 20.0
10.0 21.0
10.5 MHz
MHz
2 Master Clock Low tMCL 20 ns
3 Master Clock High tMCH 20 ns
ZL50232 Data Sheet
23
Zarlink Semiconductor Inc.
Characteristics are over re commended operating conditions unless otherwise stated.
Typical figures are at 25°C, VDD1 = 3.3 V and for desi gn aid only: not guaranteed and not subject to production testing.
Figure 12 - ST-BUS Timing at 2.048 Mbps
AC Electrical Characteristics - Motorola Non-Multiplexed Bus Mode
Characteristics Sym. Min. Typ.Max. Units Test Conditions
1CS
setup from DS falling tCSS 0ns
2R/W
setup from DS falling tRWS 0ns
3 Address setup from DS falling tADS 0ns
4CS
hold after DS rising tCSH 0ns
5R/W
hold after DS rising tRWH 0ns
6 Address hold after DS rising tADH 0ns
7 Data delay on read tDDR 79 ns
8 Data hold on read tDHR 315ns
9 Data setup on write tDSW 0ns
10 Data hold on write tDHW 0ns
11 Acknowled gment delay tAKD 80 ns
12 Acknowledgment hold time tAKH 08ns
13 IRQ delay tIRD 20 65 ns
VTT
VTT
F0i
C4i
tFPW
Rout/Sout
Rin/Sin
tFPH
tSOD
tSIH
tCH tCL
Bit 0, Channel 31
tFPS tCP
tSIS
VTT
VTT
Bit 7, Channel 0 Bit 6, Channel 0 Bit 5, Channel 0
Bit 0, Channel 31 Bit 7, Channel 0 Bit 6, Channel 0 Bit 5, Channel 0
VHM
VLM
tr
tf
ZL50232 Data Sheet
24
Zarlink Semiconductor Inc.
Figure 13 - GCI Interface Timing at 2.048 Mbps
Figure 14 - Output Driver Enable (ODE)
Figure 15 - Master Clock
VTT
VTT
F0i
C4i
tFPW
Sout/Rout
Sin/Rin
tFPH
tSOD
tSIH
tCH tCL
Bit 7, Channel 31
tFPS tCP
tSIS
VTT
VTT
Bit 0, Channel 0 Bit 1, Channel 0 Bit 2, Channel 0
Bit 7, Channel 31 Bit 0, C hannel 0 Bit 1, Channel 0 Bit 2, C hannel 0
tr
tf
VHM
VLM
VTT
HiZ
HiZ
Sout/Rout
ODE tODE
tODE
Valid Data
VTT
tMCH
tMCL
VTT
MCLK
ZL50232 Data Sheet
25
Zarlink Semiconductor Inc.
Figure 16 - Motorola Non-Multiplexed Bus Timing
DS
A0-A10
CS
D0-D7
D0-D7
READ
WRITE
tCSS tCSH
tADH
tDHR
tRWS
R/W
tADS
tRWH
tDHW
tAKD
tDSW
tDDR
tAKH
DTA
VTT
VTT
VTT
VTT
VTT
VTT
VTT
VALID ADDRESS
VALID READ DATA
VALID WRITE DATA
tIRD
IRQ VTT
ZL50232 Data Sheet
26
Zarlink Semiconductor Inc.
8.0 Register Descript ion
Echo Canceller A (ECA): Control Register 1
Power-up 00hex R/W Address: 00hex + Base Address
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
Reset INJDis BBM PAD Bypass AdpDis 0 ExtDI
Functional Description of Register Bits
Reset When high, the power-up initialization is executed. This presets all register bits including
this bit and clears the Adaptive Filter coef ficients.
INJDis When high, the noise injection process is disabled. When low noise injection is enabled.
BBM When high, the Back to Back configuration is enabled. When low, the Normal
configuration is enabled. Note: Do not enable Extende d-Delay and BBM configurations at
the same time. Always set both BBM bits of the two echo cancellers (Control Register 1)
of the same group to the same logic value to avoid conflict.
PAD When high, 12 dB of attenuation is inserted into the Rin to Rout path. Wh en low, the
Gains register controls the signal levels.
Bypass When high, Sin data is by-passed to Sout and Rin data is by-p assed to Rout. The
Adaptive Filter coefficients are set to zero and the filter adaptation is stoppe d. When low,
output data on both Sout and Rout is a function of the echo canceller algorithm.
AdpDis When high, echo canceller adaptation is disabled. The Voice Processor cancels echo.
When low, the echo canceller dynamically adapts to the echo path characteristics.
0 Bits marked as “1” or “0” are reserved bits and should be written as indicated.
ExtDl When high, Echo Cancellers A and B of the same group are internally cascaded into one
128 ms echo canceller. When low, Echo Cancellers A and B of the same group operate
independently.
Echo Canceller B (ECB): Control Register 1
Power-up 02hex R/W Address: 20hex + Base Address
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
Reset INJDis BBM PAD Bypass AdpDis 1 0
Functional Description of Register Bits
Reset When high, the power-up initialization is executed which presets all register bit s including
this bit and clears the Adaptive Filter coef ficients.
INJDis When high, the noise injection process is disabled. When low, noise inje ction is enabled.
BBM When high, the Back to Back configuration is enabled. When low, the Normal
configuration is enabled. Note: Do not enable Extende d-Delay and BBM configurations at
the same time. Always set both BBM bits of the two echo cancellers (Control Register 1)
of the same group to the same logic value to avoid conflict.
PAD When high, 12 dB of attenuation is inserted into the Rin to Rout path. Wh en low, the
Gains register controls the signal levels.
Bypass When high, Sin data is by-passed to Sout and Rin data is by-p assed to Rout. The
Adaptive Filter coefficients are set to zero and the filter adaptation is stoppe d. When low,
output data on both Sout and Rout is a function of the echo canceller algorithm.
AdpDis When high, echo canceller adaptation is disabled. The Voice Processor cancels echo.
When low, the echo canceller dynamically adapts to the echo path characteristics.
1 Bits marked as “1” or “0” are reserved bits and should be written as indicated.
0 Control Register 1 (Echo Canceller B) Bit 0 is a reserved bit and should be written “0”.
ZL50232 Data Sheet
27
Zarlink Semiconductor Inc.
Note: In order to correctly write to Control Register 1 and 2 of ECB, it is necessary to write the data twice to the register, one
immediately after another. The two writes must b e separated by at least 350n s and no more than 2 0 us.
Power-up
00hex
ECA: Control Register 2 R/W Address:
01hex + Base Address
ECB: Control Register 2 R/W Address:
21hex + Base Address
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
TDis PHDis NLPDis AutoTD NBDis HPFDis MuteS MuteR
Functional Description of Register Bits
TDis When high, tone detection is disabled . When low, tone detection is enabled. When both
Echo Cancellers A and B TDis bits are high, Tone Disable processors are disabled
entirely and are put into Power Down mode.
PHDis When high, the tone detectors will trigger upon the presence of a 2100 Hz tone regardless
of the presence/absence of periodic phase reversals. When low, the tone detector s will
trigger only upon the presence of a 2100 Hz tone with periodic phase reversals.
NLPDis When high, the non-linear process or is disabled. When low, the non-linear processors
function normally. Useful for G.165 conformance testing.
AutoTD When high, the ech o canceller puts itself in Bypass mod e when the to ne detec tors detect
the presence of 2100 Hz tone. See PHDis for qualification of 2100 Hz tones.
When low, the echo canceller algorithm will remain operational regardless of the state of
the 2100 Hz tone detectors.
NBDis When high, the narrow-band detector is disabled. When low, the narrow-band detector is
enabled.
HPFDis When high, the offset nulling high pass filters are bypassed in the Rin and Sin paths.
When low, the offset nulling filters are active and will remove DC offsets on PCM input
signals.
MuteS When high, data on Sout is muted to quiet code. When low, Sout carries active code.
MuteR When high, data on Rout is muted to quiet code. When low, Rout carries active code.
ZL50232 Data Sheet
28
Zarlink Semiconductor Inc.
Power-up
00hex
ECA: Status Register Read Address:
02hex + Base Address
ECB: Status Register Read Address:
22hex + Base Address
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
Reserve TD DTDet Reserve Reserve Reserve TDG NB
Functional Description of Register Bits
Reserve Reserved bit
TD Logic high indicates the presence of a 2100Hz tone
DTDet Logic high indicates the presence of a double-talk condition
Reserve Reserved bit
Reserve Reserved bit
Reserve Reserved bit
TDG Tone detection status bit gated with the AutoTD bit. (Control Register 2)
Logic high indicates that AutoTD has been enabled and the tone detector has detected
the presence of a 2100Hz tone.
NB Logic high indicates the presenc e of a narrow-band signal on Rin
Power-up
00hex
ECA: Flat Delay Register (FD) R/W Address:
04hex + Base Address
ECB: Flat Delay Register (FD) R/W Address:
24hex + Base Address
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
FD7 FD6 FD5 FD4 FD3 FD2 FD1 FD0
Power-up
00hex
ECA: Decay Step Number Register (NS) R/W Address:
07hex + Base Address
ECB: Decay Step Number Register (NS) R/W Address:
27hex+ Base Address
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
NS7 NS6 NS5 NS4 NS3 NS2 NS1 NS0
Power-up
04hex
ECA: Decay Step Siz e Control Register (SSC) R/W Address:
06hex + Base Address
ECB: Decay Step Siz e Control Register (SSC) R/W Address:
26hex + Base Address
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
00000SSC2SSC1SSC0
Note: Bits marked with “0” are reserved bits and should be written “0
ZL50232 Data Sheet
29
Zarlink Semiconductor Inc.
Figure 17 - The MU Profile
Functional Description of Register Bits
The Exponential Decay registers (Deca y Step Number and Decay Step Size) and Flat Delay register allow the LMS
adaptation step-s ize (MU) to be programmed over the length of the FIR filter. A programmable MU profile allows the
performance of the echo canceller to be optimized for specific applications. For example, if the characteristic of the
echo response is known to have a flat delay of several milliseconds and a roughly exponential decay of the echo
impulse response, then th e MU profile can be prog rammed to approx imate this expected impulse resp onse the reby
improving the convergence characteristics of the Adaptive Filter. Note that in the following register descriptions, one
tap is equivalent to 125 µs (64 ms/512 tap s).
FD7-0 Flat Delay: This register defines the flat delay of the MU profile, (i.e., where the MU value is 2-16). The
delay is defined as FD7-0 x 8 taps. For example; If FD7-0 = 5, then MU=2-16 for the first 40 taps of the
echo canceller FIR filter. The valid range of FD7-0 is: 0 FD7-0 64 in normal mode and 0 FD7-0
128 in extended-delay mode. The default valu e of FD7-0 is zero.
SSC2-0 Decay Step Size Control: This register controls the step size (SS) to be used during the exponential deca y
of MU. The decay rate is defined as a decrease of MU by a factor of 2 every SS taps of the FIR filter,
where SS = 4 x2SSC2-0. For example; If SSC 2-0 = 4, then MU is reduced by a factor of 2 every 64 tap s of
the FIR filter. The default value of SSC2-0 is 04hex.
NS7-0 Decay Step Number: This register defines the nu mber of step s to be u sed for th e decay of MU where each
step has a period of SS taps (see SSC2-0). The start of the exponential decay is defined as: Filter
Length (512 or 1024) - [Decay Step Number (NS7-0) x Step Size (SS)] w he r e S S = 4 x2 SSC2-0.
For example; If NS7-0=4 and SSC2-0=4, then the exponential decay start value is 512 - [NS7-0 x SS] =
512 - [4 x (4x24)] = 256 taps for a filter length of 512 taps.
Amplitude of MU
Time
Flat Delay (FD7-0)
Step Size (SS)
1.0
2-16
FIR Filter Length (512 or 1024 taps)
Number of Steps (NS7-0)
ZL50232 Data Sheet
30
Zarlink Semiconductor Inc.
The Table 5 below is the same Table shown on page 9)
Power-up
FBhex
ECA: Control Register 3 R/W Address:
08hex + Base Address
ECB: Control Register 3 R/W Address:
28hex + Base Address
Bit 7 Bit 6 Bit 5 Bit 4 Bi t 3 Bit 2 Bit 1 Bit 0
NLRun2 InjCtrl NLRun1 RingClr Reserve PathClr PathDet NLPSel
Functional Description of Register Bits
NLRun2 When high, the comfort noise level estimator actively rejects double-talk as being backgroun d
noise. When low, the noise level estimator makes no such distinction.
InjCtrl Selects which noise ramping scheme is used. See Table below.
NLRun1 When high, the comfort noise level estimator actively rejects uncancelled echo as being
background noise. When low, the noise level estimator makes no such distinction.
RingClr When high, the instability detector is activated. When low, the instability detector is disabled.
Reserve Reserved bit. Must always be set to one for normal operation.
PathClr When high, the current echo channel estimate will be cleared and the echo canceller will enter
fast convergence mode upon detection of a path change. When low , the echo canceller will keep
the current p ath es timate but re vert to fast convergenc e mod e upon de tec tion of a path change.
Note: this bit is ignored if PathDet is low.
PathDet When high, the path change detector is activ ated. When low, the path change detector is
disabled.
NLPSel When high, the Advanced NLP is selected. When low, the original NLP is selected.
Feature Register or Bit(s) Advanced
NLP Default
Value Original NLP
Default Value
NLP Selection NLPSel (Control Register 3) 1 0 (feature
not supported)
Reject uncancelled echo as noise NLRun1 (Control Register 3) 1 0 (feature
not supported)
Reject double-talk as noise NLRun2 (Control Register 3) 1 0 (feature
not supported)
Noise level estimator ramping
scheme InjCtrl (Control Registe r 3) 1 0 (feature
not supported)
Noise level ramping rate NLInc (Noise Control) 5hex Chex
Noise level scaling Noise Scaling 16hex 74hex
Table 5 - Comparison of the NLP Types
ZL50232 Data Sheet
31
Zarlink Semiconductor Inc.
Power-up
54hex
ECA: Control Register 4 R/W Address:
09hex + Base Address
ECB: Control Register 4 R/W Address:
29hex + Base Address
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
0 SD2 SD1 SD0 0 Slow2 Slow1 Slow0
Functional Description of Register Bits
0 Must be set to zero.
SupDec These three bits (SD2,SD1,SD0) control how long the echo canceller remains in a fast
convergence state following a path change, Reset or By pass operation. A value of zero will keep
the echo canceller in fast convergence indefinitely.
0 Must be set to zero.
Slow Slow convergence mode speed adjustment.(Bits Slow2, Slow1,Slow0)
For Slow = 1, 2, ..., 7, slow convergence speed is reduced by a factor of 2Slow as compared to
normal adapt ation.
For Slow = 0, no adaptation occurs during slow convergence.
Power-up
16hex
ECA: Noise Scaling (NS) R/W Address:
0Ahex + Base Address
ECB: Noise Scaling (NS) R/W Address:
2Ahex + Base Address
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
NS7 NS6 NS5 NS4 NS3 NS2 NS1 NS0
Functional Description of Register Bits
This register is used to scale the co mfort noise up or down. Large r values will increase the relative level of
comfort noise. The default value of 16hex will provide G.168 compliance with the Advanced NLP. A value of
74hex is recommended if the original NLP is used.
Power-up
45hex
ECA: Noise Control R/W Address:
0Bhex + Base Address
ECB: Noise Control R/W Address:
2Bhex + Base Address
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 B it 2 Bit 1 B it 0
Reserve Reserve Reserve Reserve NLInc3 NLInc2 NLInc1 NLInc0
Functional Description of Register Bits
Reserve Reserved bits. Must be set to 4hex fo r normal operation.
NLInc Noise level estimator ramping rate. When InjCtrl = 1, a lower value will give faster ramping.
When InjCtrl = 0, a higher value will give faster ramping. The default value of 5hex will provide
G.168 com pliance with InjCtrl = 1. A value of Chex is recommended if InjCtrl = 0.
ZL50232 Data Sheet
32
Zarlink Semiconductor Inc.
Power-up
N/A
ECA: Rin Peak Detect Register 2 (RP) Read Address:
0Dhex + Base Address
ECB: Rin Peak Detect Register 2 (RP) Read Address:
2Dhex + Base Address
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
RP15 RP14 RP13 RP12 RP11 RP10 RP9 RP8
Power-up
N/A ECA: Rin Peak Detect Register 1 (RP) Read Address:
0Chex + Base Address
ECB: Rin Peak Detect Register 1 (RP) Read Address:
2Chex + Base Address
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
RP7 RP6 RP5 RP4 RP3 RP2 RP1 RP0
Functional Description of Register Bits
These peak detector registers allow the user to monitor the receive in (Rin) peak signal level. The in formation
is in 16-bit 2’s complement linear coded format presented in two 8 bit registers for each echo canceller. The
high byte is in Register 2 and the low byte is in Register 1.
Power-up
N/A
ECA: Sin Peak Detect Register 2 (SP) Read Address:
0Fhex + Base Address
ECB: Sin Peak Detect Register 2 (SP) Read Address:
2Fhex + Base Address
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
SP15 SP14 SP13 SP12 SP11 SP10 SP9 SP8
Power-up
N/A ECA: Sin Peak Detect Register 1 (SP) Read Address:
0Ehex + Base Address
ECB: Sin Peak Detect Register 1 (SP) Read Address:
2Ehex + Base Address
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
SP7 SP6 SP5 SP4 SP3 SP2 SP1 SP0
Functional Description of Register Bits
These peak detector regis ters allow the user to monitor the send in (Sin) peak sign al level. The information is in
16-bit 2’s complement linear coded format presented in two 8 bit registers for each echo canceller. The high
byte is in Register 2 and the low byte is in Register 1.
ZL50232 Data Sheet
33
Zarlink Semiconductor Inc.
Power-up
N/A
ECA: Error Peak Detect Register 2 (EP) Read Address:
11hex + Base Address
ECB: Error Peak Detect Register 2 (EP) Read Address:
31hex + Base Address
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
EP15 EP14 EP13 EP12 EP11 EP10 EP9 EP8
Power-up
N/A
ECA: Error Peak Detect Register 1 (EP) Read Address:
10hex + Base Address
ECB: Error Peak Detect Register 1 (EP) Read Address:
30hex + Base Address
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
EP7 EP6 EP5 EP4 EP3 EP2 EP1 EP0
Functional Description of Register Bits
These peak detector registers allow the use r to monitor the error signal peak level. The information is in 16 bit
2’s complement linear coded format presented in two 8 bit registers for each echo canceller. The high byte is in
Register 2 and the low byte is in Register 1.
Power-up
48hex
ECA: Double-Talk Detection Threshold Register 2 R/W Address:
15hex + Base Address
ECB: Double-Talk Detection Threshold Register 2 R/W Address:
35hex + Base Address
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
DTDT15 DTDT14 DTDT13 DTDT12 DTDT11 DTDT10 DTDT9 DTDT8
Power-up
00hex
ECA: Double-Talk Detection Threshold Register 1 R/W Address:
14hex + Base Address
ECB: Double-Talk Detection Threshold Register 1 R/W Address:
34hex + Base Address
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
DTDT7 DTDT6 DTDT5 DTDT4 DTDT3 DTDT2 DTDT1 DTDT0
Functional Description of Register Bits
This register allows the user to program the level of Double-Talk Detection Threshold (DTDT). The 16 bit 2’s
complement linear value defaults to 4800hex= 0.5625 or -5 dB. The maximum value is 7FFFhex = 0.9999 or
0 dB. The high byte is in Register 2 and the low byte is in Register 1.
ZL50232 Data Sheet
34
Zarlink Semiconductor Inc.
Power-up
0Chex
ECA: Non-Linear Processor Threshold Register 2
(NLPTHR) R/W Address:
19hex + Base Address
ECB: Non-Linear Processor Threshold Register 2
(NLPTHR) R/W Address:
39hex + Base Address
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
NLP15 NLP14 NLP13 NLP12 NLP11 NLP10 NLP9 NLP8
Power-up
E0hex
ECA: Non-Linear Processor Threshold Register 1
(NLPTHR) R/W Address:
18hex + Base Address
ECB: Non-Linear Processor Threshold Register 1
(NLPTHR) R/W Address:
38hex + Base Address
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
NLP7 NLP6 NLP5 NLP4 NLP3 NLP2 NLP1 NLP0
Functional Description of Register Bits
This register allows the user to pr ogram the lev el of the Non -Linear Pro ces sor Thres hold (NLPTHR). The 16 bit
2’s compleme nt linear value default s to 0CE 0hex = 0.1 or -20.0 dB. The maximum value is 7FFFhex = 0.9999 or
0 dB. The high byte is in Register 2 and the low byte is in Register 1.
Power-up
40hex
ECA: Adaptation Step Size Register 2 (MU) R/W Address:
1Bhex + Base Address
ECB: Adaptation Step Size Register 2 (MU) R/W Address:
3Bhex + Base Address
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
MU15 MU14 MU13 MU12 MU11 MU10 MU9 MU8
Power-up
00hex
ECA: Adaptation Step Size Register 1 (MU) R/W Address:
1Ahex + Base Address
ECB: Adaptation Step Size Register 1 (MU) R/W Address:
3Ahex + Base Address
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
MU7 MU6 MU5 MU4 MU3 MU2 MU1 MU0
Functional Description of Register Bits
This register allows the user to program the level of MU. MU is a 16 bit 2’s complement value which defaults to
4000hex = 1.0 The maximum value is 7FFFhex or 1 .9999 decimal. The high byte is in Regis ter 2 and the low byte
is in Register 1.
ZL50232 Data Sheet
35
Zarlink Semiconductor Inc.
Power-up
44hex
ECA: Gains Register 2 R/W Address:
1Dhex + Base Address
ECB: Gains Register 2 R/W Address:
3Dhex + Base Address
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
0 Rin2 Rin1 Rin0 0 Rout2 Rout1 Rout0
Power-up
44hex
ECA: Gains Register 1 R/W Address:
1Chex + Base Address
ECB: Gains Register 1 R/W Address:
3Chex + Base Address
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
0 Sin2 Sin1 Sin0 0 Sout2 Sout1 Sout0
Functional Description of Register Bits
This register is used to select g ain valu es on RIN, ROUT, SIN and SOUT.
Gains is split into fou r gro up s of four bits. Each group maps to a diff erent signal port (as indic ate d above), and
has three gain bits. The following table indicates how these gain bits are used:
Bit2 Bit1 Bit0 Gain Level
1 1 1 +9 dB
1 1 0 +6 dB)
1 0 1 +3 dB
1 0 0 0 dB (default)
0 1 1 -3 dB
0 1 0 -6 dB
0 0 1 -9 dB
0 0 0 -12 dB
Note that the -12 dB PAD bit in Control Register 1 provides 12 dB of attenuation in the Rin to Rout path, and
will override the settings in Gains.
ZL50232 Data Sheet
36
Zarlink Semiconductor Inc.
Main Control Register 0 (EC Group 0)
Power-up 00hex R/W Addres s: 400hex
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bi t 0
WR_all ODE MIRQ MTDBI MTDAI Format Law PWUP
Functional Description of Register Bits
WR_all Write all control bit: When high, Group 0-15 Echo Cancellers Registers are mapped into 0000hex
to 0003Fhex which is Group 0 address mapping. Useful to initialize the 16 Groups of Echo
Cancellers as per Group 0. When low, address mapping is per Figure 10. Note: Only the Main
Control Register 0 has the WR_all bit
ODE Output Data En able: This contro l bit is logically AND’d with the ODE inp ut pin. When both ODE bit
and ODE input pin are high, the Rout and Sout outputs are enabled. When the ODE bit is low or
the ODE input pin is low, the Rout and Sout outputs are high impedance. Note: Only the Main
Control Register 0 has the ODE bit.
MIRQ Mask Interrupt: When high, all the interrupts from the Tone Detectors output are masked. The
Tone Detectors operate as specified in their Echo Canceller B, Control Register 2.
When low, the Tone Detectors Interrupts are active.
Note: Only the Main Control Register 0 has the MIRQ bit.
MTDBI Mask Tone Detector B Interrupt: When high, the Tone Detector interrupt output from Echo
Canceller B is masked. The Tone Detector operates as specified in Echo Canceller B, Control
Register 2. When low, the Tone Detector B Interrupt is active.
MTDAI Mask Tone Detector A Interrupt: When high, the Tone Detector interrupt output from Echo
Canceller A is masked. The Tone Detector operates as specified in Echo Canceller A, Control
Register 2. When low, the Tone Detector A Interrupt is active.
Format ITU-T/Sign Mag: When high, both Echo Cancellers A and B for a given group, accept ITU-T
(G.711) PCM code. When low, both Echo Cancellers A and B for a given group, accept
sign-magnitude PCM code.
Law A/µ Law: When high, both Echo Cancellers A and B for a given group, acc ept A-Law companded
PCM code. When low, both Echo Cancellers A and B for a given gro up, accept µ-Law comp anded
PCM code.
PWUP Power-UP: When high, both Echo Cancellers A and B and Tone Detectors for a given group, are
active. When low, both Echo Cancellers A and B and Tone Detecto rs for a given group, are placed
in Power Down mode. In this mode, the correspond ing PCM data are bypassed from Rin to Rout
and from Sin to Sout with two frames delay. When the PWUP bit toggles from zero to one, the
echo canceller A and B execute their initialization routine which presets their registers, Base
Address+00hex to Base Address+3Fhex, to default power up value and clears the Adaptive Filter
coefficients. Two frames are necessary for the initialization routine to execute properly. Once the
initialization routine is executed, the user can set the per channel Control Registers for their
specific application.
ZL50232 Data Sheet
37
Zarlink Semiconductor Inc.
Main Control Register 1 (EC Group 1) R/W Address: 401hex
Main Control Register 2 (EC Group 2) R/W Address: 402hex
Main Control Register 3 (EC Group 3) R/W Address: 403hex
Main Control Register 4 (EC Group 4) R/W Address: 404hex
Main Control Register 5 (EC Group 5) R/W Address: 405hex
Main Control Register 6 (EC Group 6) R/W Address: 406hex
Main Control Register 7 (EC Group 7) R/W Address: 407hex
Main Control Register 8 (EC Group 8) R/W Address: 408hex
Main Control Register 9 (EC Group 9) R/W Address: 409hex
Main Control Register 10 (EC Group 10) R/W Address: 40Ahex
Main Control Register 11 (EC Group 11) R/W Address: 40Bhex
Main Control Register 12 (EC Group 12) R/W Address: 40Chex
Main Control Register 13 (EC Group 13) R/W Address: 40Dhex
Main Control Register 14 (EC Group 14) R/W Address: 40Ehex
Main Control Register 15 (EC Group 15) R/W Address: 40Fhex
Power-up 00hex
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
Unused Unused Unused MTDBI MTDAI Format Law PWUP
Functional Description of Register Bits
Unused Unused Bits.
MTDBI Mask Tone Detector B Interrupt: When high, the Tone Detector interrupt output from Echo Canc eller
B is masked. The Tone Detector operates as specified in Echo Canceller B, Control Register 2.
When low, the Tone Detector B Interrupt is active.
MTDAI Mask Tone Detector A Interrupt: When high, the Tone Detector interrupt output from Echo Canc eller
A is masked. The Tone Detector operates as specified in Echo Canceller A, Control Register 2.
When low, the Tone Detector A Interrupt is active.
Format ITU-T/Sign Mag: When high, both Echo Cancellers A and B for a given group, select ITU-T (G.711)
PCM code. When low, both Echo Cancellers A and B for a give n group, select si gn-magnitude PCM
code.
Law A/µ Law: When high, both Echo Cancellers A and B for a given group, select A-Law companded
PCM code. When low, both Echo Cancellers A and B for a given group, select µ-Law compande d
PCM code.
PWUP Power-UP: When high, both Echo Canc ellers A and B and Tone Detectors for a given group, are
active. When low, both Echo Cancellers A and B and Tone Detectors for a given group, are placed
in Power Down mode. In this mode, the corresponding PCM data are bypassed from Rin to Rout
and from Sin to Sout with two frames delay. When the PWUP bit toggles from zero to one, the
echo cancellers A and B execute their initialization routine which preset s their registers, Base
Address+00hex to Base Address+3Fhex, to default Reset Value and clears the Adaptive Filter
coef ficients. Two frames are necessary for the initialization routine to execute properly. Once the
initialization routine is executed, the user can set the per c hannel Control Re gisters for their spec ific
application.
ZL50232 Data Sheet
38
Zarlink Semiconductor Inc.
Interrupt FIFO Register
Power-up 00hex R/W Address: 410hex
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
IRQ0 0I4I3I2I1I0
Functional Description of Register Bits
IRQ Logic high indicates an interrupt has occurred. IRQ bit is cleared after the Interrupt FIFO register
is read. Logic Low indicates that no interrupt is pending and the FIFO is empty.
0 Unused bit. Alw a ys ze ro .
0 Unused bit. Alw a ys ze ro .
I<4:0> I<4:0> binary code indicates the channel number at which a Tone Detector state cha nge has
occurred. Note: Whenever a Tone Disable is detected or released, an interrupt is generated.
Test Register
Power-up 00hex R/W Address: 411hex
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
Reserve Reserve Reserve Reserve Reserve Reserve Reserve Tirq
Functional Description of Register Bits
Reserve Reserved bits. Must always be set to zero for normal operation.
Tirq Test IRQ: Useful for the application engineer to verify the interrupt service ro utine. When high,
any change to MTDBI and MTDAI bits of the Main Control Register will cause an interrupt and its
corresponding channel number will be available from the Interrupt FIFO Regis ter. When low,
normal opera tion is selected.
www.zarlink.com
Information relating to products and services furnished herein by Zarlink Semiconductor Inc. or its subsidiaries (collectively “Zarlink”) is believed to be reliable.
However, Zarlink assumes no liability for errors that may appear in this publication, or for liability otherwise arising from the application or use of any such
information, product or service or for any infringement of patents or other intellectual property rights owned by third parties which may result from such application or
use. Neither the supply of such information or purchase of product or service conveys any license, either express or implied, under patents or other intellectual
property rights owned by Zarlink or licensed from third parties by Zarlink, whatsoever. Purchasers of products are also hereby notified that the use of product in
certain ways or in combination with Zarlink, or non-Zarlink furnished goods or services may infringe patents or other intellectual property rights owned by Zarlink.
This publication is issued to provide information only and (unless agreed by Zarlink in writing) may not be used, applied or reproduced for any purpose nor form part
of any order or contract nor to be regarded as a representation relating to the products or services concerned. The products, their specifications, services and other
information appearing in this publication are subject to change by Zarlink without notice. No warranty or guarantee express or implied is made regarding the
capability, performance or suitability of any product or service. Information concerning possible methods of use is provided as a guide only and does not constitute
any guarantee that such methods of use will be satisfactory in a specific piece of equipment. It is the user’s responsibility to fully determine the performance and
suitability of any equipment using such information and to ensure that any publication or data used is up to date and has not been superseded. Manufacturing does
not necessarily include testing of all functions or parameters. These products are not suitable for use in any medical products whose failure to perform may result in
significant injury or death to the user. All products and materials are sold and services provided subject to Zarlink’s conditions of sale which are available on request.
Purchase of Zarlink’s I2C components conveys a licence under the Philips I2C Patent rights to use these components in and I2C System, provided that the system
conforms to the I2C Standard Specification as defined by Philips.
Zarlink, ZL and the Zarlink Semiconductor logo are trademarks of Zarlink Semiconductor Inc.
Copyright Zarlink Semiconductor Inc. All Rights Reserved.
TECHNICAL DOCUMENTATION - NOT FOR RESALE
For more information about all Zarlink products
visit our Web Site at