Is Now Part of To learn more about ON Semiconductor, please visit our website at www.onsemi.com ON Semiconductor and the ON Semiconductor logo are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor's product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by ON Semiconductor. "Typical" parameters which may be provided in ON Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. FPF2700 / FPF2701 / FPF2702 -- AccuPowerTM 0.4~2 A Adjustable Over-Current Protection Load Switches Features Description The AccuPowerTM FPF270X series is a family of current-limit load switches that provide full protection to systems and loads from excess current conditions. Minimum current limit is adjustable from 0.4 A to 2.0 A. The FPF270X contains a slew-rate-controlled N-channel MOSFET and slew-rated turn-on to prevent power bus disturbances from being caused by "hot plugging" loads or momentary excess load demands. The input voltage range is 2.8 V to 36 V. Loads can be activated or deactivated with a low-voltage logic-compatible ON pin. Fault conditions can be monitored using the error flag pin and/or the power-good pin. 2.8 V to 36 V Input Voltage Range Typical RDS(ON)=88 m 0.4 A to 2 A Adjustable Current Limit (Min.) Slew Rate Controlled ESD Protected, above 2000 V HBM Thermal Shutdown Active LOW Enable UVLO Protection Power-Good Output Applications Each member of the FPF270X family serves a category of load-fault response. All devices clamp the load current so that it cannot exceed an externally programmed current level. An over temperature feature provides further device protection in case of excessive levels of power dissipation. Motor Drives Digital Cameras Consumer Electronics Industrial FPF2700 responds to an overload condition that lasts longer than a fixed blanking period by turning off the load, followed by a retry after the auto-restart time. Computing Hard Disk Drives Telecom Equipment FPF2701 responds to an overload condition that lasts longer than a fixed blanking period by latching off the load. The load remains off unless either the ON pin is toggled or the input voltage cycles through UVLO. Figure 1. MLP (Top View) Figure 2. MLP (Bottom View) FPF2702 is intended to be used with external fault management. Like the FPF2700 and FPF2701, it sets the fault signal pin LOW when it activates current clamping. This device is intended for applications where external fault management coordinates the overload response with the FPF2702. The FPF270X is available in a space-saving, Lead and Halogen free, 8-lead, MLP 3x3 mm and SO8 packages. Figure 3. SO8 (Top View) Ordering Information Part Number Current Limit [A] Current Limit Blanking Time [ms] Auto-Restart Time [ms] ON Pin Activity Package FPF2700MPX 0.4 - 2.0 0.5 127.5 Active LOW MLP3X3 FPF2701MPX 0.4 - 2.0 0.5 NA Active LOW MLP3X3 FPF2702MPX 0.4 - 2.0 NA NA Active LOW MLP3X3 FPF2700MX 0.4 - 2.0 0.5 127.5 Active LOW SO8 FPF2701MX 0.4 - 2.0 0.5 NA Active LOW SO8 FPF2702MX 0.4 - 2.0 NA NA Active LOW SO8 (c) 2010 Fairchild Semiconductor Corporation FPF2700 / FPF2701 / FPF2702 * Rev. 1.0.3 www.fairchildsemi.com FPF2700 / FPF2701 / FPF2702 -- AccuPowerTM 0.4~2A Adjustable Over-Current Protection Load Switches December 2013 36 V MAX. VIN VOUT ON FLAGB TO LOAD OFF ON VIN 2.8 V - 36 V 100K 100K COUT CIN ISET PGOOD RSET GND Figure 4. Typical Application Block Diagram IN VDD VREF BGAP/BIAS Reg Current Limit SOA Protection Current Limit UVLO CONTROL LOGIC VREF ON THERMAL PROTECTION CHARGE PUMP ISET VIN OUT VOUT PGOOD FLAGB + - FPF2700 / FPF2701 / FPF2702 -- AccuPowerTM 0.4~2A Adjustable Over-Current Protection Load Switches Application Diagram GND Figure 5. Block Diagram (c) 2010 Fairchild Semiconductor Corporation FPF2700 / FPF2701 / FPF2702 * Rev. 1.0.3 www.fairchildsemi.com 2 VOUT 8 1 VIN FLAGB 7 2 PGOOD VIN 1 8 VOUT PGOOD 2 7 FLAGB ISET 3 6 NC ON 4 5 GND GND NC 6 3 ISET GND 5 4 ON Figure 6. MLP (Bottom View) Figure 7. SO8 (Top View) Pin Definitions Pin # Name Description 1 VIN 2 PGOOD Power-Good Output. Open-drain output to indicate that output voltage has reached 90% of input voltage. 3 ISET Current Limit Set Input. A resistor from ISET to ground sets the current limit for the switch. 4 ON 5 GND 6 NC 7 FLAGB Fault Output. Active LOW, open-drain output that indicates current limit, under-voltage, or over-temperature state. 8 VOUT Switch Output. Output of the power switch. Supply Input. Input to the power switch and the supply voltage for the IC. ON Control Input. Active LOW. Ground No connection. Leave open or connect to ground. (c) 2010 Fairchild Semiconductor Corporation FPF2700 / FPF2701 / FPF2702 * Rev. 1.0.3 FPF2700 / FPF2701 / FPF2702 -- AccuPowerTM 0.4~2A Adjustable Over-Current Protection Load Switches Pin Configurations www.fairchildsemi.com 3 Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be operable above the recommended operating conditions and stressing the parts to these levels is not recommended. In addition, extended exposure to stresses above the recommended operating conditions may affect device reliability. The absolute maximum ratings are stress ratings only. Symbol Parameter Min. Max. Unit PGOOD, FLAGB, VIN to GND -0.3 40 V VOUT to GND -0.3 VIN + 0.3 V ON to GND -0.3 6 V (1) MLP 3x3 , See Figure 8 1.25 PD Power Dissipation (TA=25C) ISW Maximum Continuous Switch Current 3.5 A TJ Operating Junction Temperature -40 +125 C TSTG Storage Temperature -65 +150 C ESD Electrostatic Discharge Protection Level Human Body Model, JESD22-A114 2000 Charged Device Model, JESD22-C101 2000 JA Thermal Resistance, Junction to Ambient MLP 3x3 , See Figure 8 (1) SO8 , See Figure 10 1.00 (1) V 80 (1) SO8 , See Figure 10 W 102 C/W Note: 1. Thermal resistance, JA, is determined with the device mounted on a one inch square pad, 2 oz copper pad, and a 1.5 x 1.5 in. board of FR-4 material. 2 Figure 8. 80C/W Mounted on a 1in Pad of 2-oz. Copper Figure 9. 226C/W Mounted on a Minimum Pad of 2-oz. Copper 2 Figure 10. 102C/W mounted on a 1in Pad of 2-oz. Copper Figure 11. 181C/W Mounted on a Minimum Pad of 2-oz. Copper Recommended Operating Conditions The Recommended Operating Conditions table defines the conditions for actual device operation. Recommended operating conditions are specified to ensure optimal performance. Fairchild does not recommend exceeding them or designing to Absolute Maximum Ratings. Symbol Parameter Min. Max. Unit VIN Input Supply Voltage 2.8 36.0 V TA Ambient Operating Temperature -40 85 C (c) 2010 Fairchild Semiconductor Corporation FPF2700 / FPF2701 / FPF2702 * Rev. 1.0.3 FPF2700 / FPF2701 / FPF2702 -- AccuPowerTM 0.4~2A Adjustable Over-Current Protection Load Switches Absolute Maximum Ratings www.fairchildsemi.com 4 VIN=2.8 to 36 V and TA=-40 to +85C unless otherwise noted. Typical values are at VIN=12 V and TA=25C. Symbol Parameter Conditions Min. Typ. Max. Unit Basic Operation VIN Operating Voltage IQ Quiescent Current VIN=12 V, VON=0 V, IOUT=0 A ISHDN Shutdown Current VIN=36 V, VON=3.3 V, IOUT=0 A TA=25C, VIN=12 V RON On Resistance 2.8 36.0 V 92 140 A 5 14 A 88 114 TA=-40 to +85C, VIN=12 V 140 TA=25C, VIN=5 V 88 TA=-40 to +85C, VIN=5 V 114 m 140 VIH ON Input Logic HIGH Voltage VIN=2.8 to 36 V VIL ON Input Logic LOW Voltage VIN=2.8 to 36 V ILK ON Input Leakage VON=5.5 V or GND ISWOFF Off Switch Leakage VIN=36 V, VON=3.3 V, VOUT=0 V 0.01 FLAGB Output Logic LOW Voltage VIN=5 V, ISINK=1 mA 0.1 IFLAGB(HI) FLAGB Output Logic HIGH Leakage Current VIN=36 V, Switch On, VFLAGB=36 V VPGOOD PGOOD Trip Voltage VIN=5 V, VOUT as Percent of VIN, VOUT Rising 90 % VPGOOD(HYS) PGOOD Hysteresis VIN=5 V, VOUT as Percent of VIN, VOUT Falling 3 % VPGOOD(LO) PGOOD Output Logic LOW Voltage VIN=5 V, ISINK=1 mA VFLAGB(LO) IPGOOD(HI) PGOOD Output High Leakage Current VIN=36 V, Switch ON, VPGOOD=36 V Current Limit TA=25C Short Circuit Current Limit VOUT < 2 V, Switch in OverCurrent Condition 2.0 V -1 0.1 0.8 V 1 A A 0.2 V 1 A 0.2 V 1 A +20 % Protections ILIM ISC TSD UVLO Thermal Shutdown Under-Voltage Shutdown -20 0.75 x INOM Shutdown Threshold 140 Return from Shutdown 110 Hysteresis 30 VIN Increasing 2.3 UVLO_HYST Under-Voltage Shutdown Hysteresis 2.5 A C 2.7 100 V mV Dynamic tdon Turn On Delay tdoff Turn Off Delay tR VOUT Rise Time tF VOUT Fall Time tBLANK tRESTART tCLR 2.7 0.1 RL=500 , CL=2 F ms 7.5 1.5 Over-Current Blanking Time FPF2700/1, TA=25C 0.25 0.50 0.75 ms Auto-Restart Time FPF2700, TA=25C 63.8 127.5 191.2 ms Current-Limit Response Time VIN=12 V, VON=0 V (c) 2010 Fairchild Semiconductor Corporation FPF2700 / FPF2701 / FPF2702 * Rev. 1.0.3 50 FPF2700 / FPF2701 / FPF2702 -- AccuPowerTM 0.4~2A Adjustable Over-Current Protection Load Switches Electrical Characteristics s www.fairchildsemi.com 5 VOUT 90 % 90 % 10 % tR 10 % tF 3.3 V VON 50 % 50 % 90 % 10 % VOUT tdon tdoff tON = tR + tdon tOFF = tF + tdoff Figure 12. Timing Diagram Typical Performance Characteristics VIN = 12 V and TA = 25C. 1.40 1.80 TA = 25C V IN = 12V 1.70 1.38 On Threshold Voltage (V) On Threshold Voltage (V) 1.60 1.35 V IH 1.33 1.30 V IL 1.28 1.50 1.40 V IH 1.30 V IL 1.20 1.10 1.25 1.00 1.23 0.90 1.20 0.80 0 5 10 15 20 25 30 35 40 -50 -25 0 25 Figure 13. ON Threshold vs. Supply 75 100 125 150 Figure 14. ON Threshold vs. Temperature 130 12 V ON = 0V TA = 125C V ON = 5V 120 TA = 125C 10 TA = 85C TA = 85C 110 Quiescent Current (A) Quiescent Current (A) 50 TJ, Junction Temperature (oC) Supply Voltage (V) TA = 25C 100 90 TA = -40C 80 8 TA = 25C 6 TA = -40C 4 2 70 60 0 0 5 10 15 20 25 30 35 40 0 Supply Voltage (V) 5 10 15 20 25 30 35 FPF2700 / FPF2701 / FPF2702 -- AccuPowerTM 0.4~2A Adjustable Over-Current Protection Load Switches Timing Diagram 40 Supply Voltage (V) Figure 15. Quiescent Current vs. Supply Voltage (ON) Figure 16. Quiescent Current vs. Supply Voltage (OFF) (c) 2010 Fairchild Semiconductor Corporation FPF2700 / FPF2701 / FPF2702 * Rev. 1.0.3 www.fairchildsemi.com 6 VIN = 12 V and TA = 25C. 100 160 95 On Resistance (m) On Resistance (m) 140 90 120 85 100 80 75 80 70 60 65 40 60 0 10 20 30 Supply Voltage (V) -50 -25 0 25 50 75 100 o125 150 TJ, Junction Temperature ( C) 40 Figure 17. On Resistance vs. Supply Voltage Figure 18. On Resistance vs. Junction Temperature 4.0 12 VIN = 12V RL = 500 CL = 2F 11 10 Rise Time (ms) Turn-On Delay (ms) 3.5 3.0 9 2.5 8 7 2.0 6 1.5 5 4 1.0 -50 -25 0 25 50 75 100 125 150 -50 -25 TJ, Junction Temperature ( oC) Figure 19. Turn-On Delay vs. Junction Temperature 0 25 50 75 100 125 150 TJ, Junction Temperature (oC) Figure 20. Output Rise Time vs. Junction Temperature 0.15 Turn Off Delay Time (ms) 2.00 0.13 Fall Time (ms) 1.90 0.11 1.80 0.09 1.70 0.07 1.60 0.05 1.50 -50 -25 0 25 50 75 100 125 150 TJ, Junction Temperature (oC) -50 -25 0 25 50 75 100 o125 150 TJ, Junction Temperature ( C) Figure 21. Turn-Off Delay vs. Junction Temperature (c) 2010 Fairchild Semiconductor Corporation FPF2700 / FPF2701 / FPF2702 * Rev. 1.0.3 FPF2700 / FPF2701 / FPF2702 -- AccuPowerTM 0.4~2A Adjustable Over-Current Protection Load Switches Typical Performance Characteristics Figure 22. Output Fall Time vs. Junction Temperature www.fairchildsemi.com 7 When VOUT<2 V, the current limit is set to 75% of ILIM. 5V VON 0V VIN VOUT 2V 0V Slew rate limited turn-on tRISE = 7.5ms IOUT ILIM Turn-on delay tDON = 2.7ms Figure 23. Normal Startup to 0.5X ILIM VIN VIN VOUT 2V 0V 12A 2V 0V 12A Current limited operation at 0.75xILIM IOUT ILIM 0.75x ILIM OUT shorted to GND and switch immediately turned OFF Current limited operation at ISET Switch turned off due to the expiration of tBLANK (FPF2700, FPF2701) or due to over-heating IOUT NOTE: Auto-restart after tRESTART (FPF2700) or tBLANK or restart after cooling Thermal Shutdown down is not shown Switch turns back ON and enters current limited operation at short circuit current limit (75% of ISET) Turn-on delay is similar ILIM tBLANK or Thermal Shutdown Load demanding 1.5X ISET Switch turned off due to the expiration of tBLANK (FPF2700, FPF2701) or due to over-heating to normal tDON ~ 2.7ms FLAGB NOTE: Auto-restart after tRESTART (FPF2700) or restart after cooling down is not shown FLAGB Figure 24. OUT Shorted to GND, Short Condition Persists (SOA Protection Followed by Current-Limited Operation) Figure 25. OUT Overloaded with 1.5X ILIM (Long-Duration Overload) VIN VOUT 2V 0V 12A VIN Rise time tR ~ 7.5ms VOUT Turn-on delay is similar to normal tDON ~ 2.7ms IOUT Normal operation IOUT ISET OUT shorted to GND and switch immediately turned OFF Normal operation ISET Output Load current demanding 1.5X ISET Switch turns back ON and enters normal operation Load demanding I=1.5X ISET removed from OUT before the expiration of tBLANK (FPF2700, FPF2701) or before over-heating FLAGB FLAGB Figure 26. OUT Shorted to GND, Short Condition Removed (SOA Protection Followed by Normal Operation) (c) 2010 Fairchild Semiconductor Corporation FPF2700 / FPF2701 / FPF2702 * Rev. 1.0.3 2V 0V 12A FPF2700 / FPF2701 / FPF2702 -- AccuPowerTM 0.4~2A Adjustable Over-Current Protection Load Switches Typical Operation Characteristics of FPF2700 and FPF2701 Figure 27. OUT Overloaded with 1.5X ILIM (Transient Overload) www.fairchildsemi.com 8 VIN VOUT 2V 0V 12A Current limited operation at 0.75xILIM IOUT Switch turned off due to over-heating ILIM 0.75x ILIM OUT shorted to GND and switch immediately turned OFF Switch turns back ON and enters current limited operation at short circuit current limit (75 % of ISET ) Turn - on delay is similar to normal tDON ~ 2.7ms FLAGB FLAGB asserts due to current limit FLAGB asserts due to Thermal Shutdown Figure 28. OUT Shorted to GND, Short Condition Persists (SOA Protection Current Limit Followed by Current Limit) VIN VOUT 2V 0V 12A Current limited operation at ISET I OUT ILIM Load demanding 1.5X ISET Switch turned off due to over-heating FLAGB FLAGB asserts due to current limit FLAGB asserts due to Thermal Shutdown Figure 29. OUT Overloaded with 1.5X ILIM (Long-Duration Overload) (c) 2010 Fairchild Semiconductor Corporation FPF2700 / FPF2701 / FPF2702 * Rev. 1.0.3 FPF2700 / FPF2701 / FPF2702 -- AccuPowerTM 0.4~2A Adjustable Over-Current Protection Load Switches Typical Operation Characteristics of FPF2702 www.fairchildsemi.com 9 VIN = 12 V and TA = 25C. Figure 30. 12V Turn-On Delay (RL=500 , COUT=2 F) Figure 31. 12 V Turn-Off Delay (RL=500 , COUT=2 F) Figure 32. 12 V Blanking Time (Output Overloaded and tblank Expired, FPF2700/01, (2) ILIM=1 A, ILOAD=3.3 A, COUT= F, RLOAD=500 ) VOC Figure 33. 12 V Restart Time (Switch Turned ON into Persistent Over-Current Condition,tRESTART~127.5 ms) FPF2700 / FPF2701 / FPF2702 -- AccuPowerTM 0.4~2A Adjustable Over-Current Protection Load Switches Typical Performance Characteristics FPF270X Figure 34. Soft Overload and Constant Current Figure 35. OUT Shorted to GND, Short Condition (ILOAD > ILIM, FPF2702 Enters Constant Current Mode, Removed (SOA Protection Followed by a Normal Running at ILIM) Operation, FPF2700 / FPF2701) Note: 2. VOC signal forces the device into an over-current condition by loading a 500 m resistor to the output through an NMOS. VOC is the gate drive of the NMOS. (c) 2010 Fairchild Semiconductor Corporation FPF2700 / FPF2701 / FPF2702 * Rev. 1.0.3 www.fairchildsemi.com 10 Description of Operation Current Limiting The FPF270X family of current limit load switches is designed to meet the power requirements of a variety of applications with wide input voltage range of 2.8 V to 36 V and adjustable current-limit value. The FPF270X family offers control and protection while providing optimum operation current for safe design practices. The core of each switch is a typical 88 m (VIN = 12 V) N-channel MOSFET and a controller capable of functioning over an input voltage range of 2.8 V to 36 V. The current limit ensures that the current through the switch doesn't exceed a maximum value while not limiting at less than a minimum value. The current-limit level is adjustable through an external resistor connected between the ISET pin and GND. The typical current limit level is adjustable from 510 mA to 2.5 A. The minimum current limit (ILIM(MIN)) range is from 0.4 A to 2.0 A, including 20% current-limit tolerance. The FPF2700 and FPF2701 have a blanking time during which the switch acts as a constant-current source (Figure 27). If the over-current condition persists beyond the blanking time, the FPF2700 latches off and shuts the switch off (Figure 32). If the ON pin is kept active, an auto-restart feature releases the switch and turns the switch on again after the auto-restart time (Figure 33). If the over-current condition persists beyond the blanking time, the FPF2701 latch-off feature shuts the switch off. The switch is kept off until the ON pin is toggled or input power is cycled. The FPF2702 has no current-limit blanking period, so it remains in a constantcurrent state until the ON pin is deactivated or the thermal shutdown turns off the switch. FPF270X offers adjustable current limiting, undervoltage lockout (UVLO), power-good indicator (PGOOD), fault flag output (FLAGB), and thermal shutdown protection. In the event of an over-current condition, the load switch limits the load to the current limit value. The current limit value for each switch can be adjusted from 400 mA to 2 A through the ISET pin. On/Off Control The ON pin is active LOW for and controls the state of the switch. Pulling the ON pin continuously to LOW holds the switch in ON state. The switch moves into OFF state when the ON pin is pulled HIGH. The ON pin can be pulled HIGH to a maximum voltage of 5.5 V. Besides the current-limiting functionality, the switch is protected by the thermal shutdown protection and an independent SOA protection circuit is available. An under-voltage condition on the input voltage or a junction temperature in excess of 140C overrides the ON control and turns off the switch. In addition, an overcurrent condition causes the switch to turn off in the FPF2700 and FPF2701 after the expiration of the blanking time. The FPF2700 has an auto-restart feature that automatically turns the switch ON again after the auto-restart time. For the FPF2701, the ON pin must be toggled to turn the switch on again. The FPF2702 does not turn off in response to an over-current condition; it remains operating in Constant-Current Mode as long as ON is enabled and the thermal shutdown or UVLO have not activated. The ON pin does not have internal pulldown or pull-up resistors and should not be left floating. SOA Protection Current Limit (IOUT > 12 A) FPF270X has an SOA protection feature to protect the load switch in response to current surges exceeding 12 A in normal operation. If a short-circuit event occurs (IOUT>12 A), the switch is turned off in about 1s by an independent Safe Operating Area (SOA) protection circuit (Figure 26, Figure 28). This feature protects the switch in case of sudden, high-current events at the output, such as a short to GND. The switch turns on automatically after a turn-on delay of about 2.7 ms. Short-Circuit Current Limit (VOUT < VSCTH = 2 V) Fault Reporting When the output voltage drops below the short-circuit threshold voltage, VSCTH, the current-limit value reconditions itself to the short-circuit current limit value, which is 75% of the nominal current limit (0.75 x ILIM,) (Figure 24). This prevents early thermal shutdown by reducing the power dissipation of the device. The V SCTH value is set at 2 V. At about VOUT = 2.1 V, the switch is removed from short-circuit current-limiting mode and the current limit is set to the nominal current limit value. Upon detection of an over-current condition, an input UVLO, or an over-temperature condition, the FLAGB signals the Fault Mode by activating LOW. In the event of an over-current condition for the FPF2700 or FPF2701, the FLAGB goes LOW at the end of the blanking time (Figure 24 and Figure 25). FLAGB goes LOW immediately for the FPF2702 (Figure 29). If the over-current condition lasts longer than blanking time, FLAGB remains LOW through the auto-restart time for the FPF2700. For the FPF2701, FLAGB is latched LOW and ON must be toggled to release it. Setting the Current Limit Value FPF270X has an adjustable 0.4 A to 2.0 A minimum current limit set through an external resistor, R SET, connected between ISET and GND. A precision RSET value must be used, such as 1% tolerance or lower, to minimize the total current limit tolerance of the system. For FPF2702, FLAGB is LOW during a fault and immediately returns HIGH at the end of the fault condition. FLAGB is an open-drain MOSFET that requires a pull-up resistor. The maximum pull-up voltage is 36 V (Figure 29). FPF2700 / FPF2701 / FPF2702 -- AccuPowerTM 0.4~2A Adjustable Over-Current Protection Load Switches Application Information Use the following equation to calculate the value of the resistor for intended typical current limit value: During shutdown, the pull-down on FLAGB is disabled to reduce current draw from the supply. A 100 k pullup resistor is recommended in the application. RSET (k) 277.5 I LIM (TYP ) ( A) (1) ILIM(TYP) is the typical current limit value based on a RSET. (c) 2010 Fairchild Semiconductor Corporation FPF2700 / FPF2701 / FPF2702 * Rev. 1.0.3 www.fairchildsemi.com 11 RSET Selection Guide Power Good Current Limit [A] RSET (k) Min. Typ. Max. 111 2.00 2.50 3.00 20 124 1.79 2.24 2.69 20 147 1.51 1.89 2.27 20 182 1.22 1.52 1.83 20 220 1.01 1.26 1.51 20 274 0.81 1.01 1.22 20 374 0.59 0.74 0.89 20 549 0.40 0.51 0.61 20 FPF270X has a power good feature. The PGOOD pin is an open-drain MOSFET that asserts HIGH when the output voltage reaches 90% of the input voltage (Figure 26). A typical 3% PGOOD hysteresis is added to PGOOD to prevent PGOOD from chattering as VOUT falls near the PGOOD threshold voltage. Tol. (%) The PGOOD pin requires an external pull-up resistor connected to an external voltage source compatible with input levels of other chips connected to this pin. PGOOD is kept LOW when the device is inactive. To save current in the OFF state, the pull-up resistor of the PGOOD pin can be connected to the output voltage when there is no battery, provided that compatibility with the input levels of other devices connected to PGOOD is observed. A typical value of 100 k is recommended for the pull up resistor. When the power-good feature is not used in the application, the PGOOD pin can be connected to GND. 2.8 2.6 2.4 ILIMIT (A) 2.2 2.0 Thermal Shutdown 1.8 Thermal shutdown protects the die from internally or externally generated excessive temperatures. During an over-temperature condition; as the temperature increases above 140C, FLAGB is activated and the switch is turned off. 1.6 1.4 1.2 1.0 0.8 0.6 When the die cools down sufficiently (die temperature drops below the threshold level), the switch automatically turns on again. To avoid unwanted thermal oscillations, a 30C (typical) thermal hysteresis is implemented between thermal shutdown entry and exit temperatures. Proper board layout is required to prevent premature thermal shutdown (see Figure 38 for thermal shutdown behavior on FPF2702). 0.4 0.2 0.0 100 200 300 400 500 600 RSET (k) Figure 36. ILIM vs. RSET Under-Voltage Lockout (UVLO) The under-voltage lockout feature turns off the switch if the input voltage drops below the under-voltage lockout threshold. With the ON pin active (ON pin pulled LOW), the input voltage rising above the under-voltage lockout threshold causes a controlled turn-on of the switch (Figure 37). The UVLO threshold voltage is set internally at 2.5 V for VIN rising. The under-voltage lockout threshold has a 0.1 V hysteresis. ON VIN VOUT 2V IOUT ILIM Thermal Cycling Device cools off ON Over current condition UVLO Threshold Device Wake up FLAGB VIN FLAGB Figure 38. FPF2702 Thermal Shutdown Behavior Rise time 10%VOUT FPF2700 / FPF2701 / FPF2702 -- AccuPowerTM 0.4~2A Adjustable Over-Current Protection Load Switches Table 1. 90%VOUT VOUT Figure 37. Under-Voltage Lockout Performance (c) 2010 Fairchild Semiconductor Corporation FPF2700 / FPF2701 / FPF2702 * Rev. 1.0.3 www.fairchildsemi.com 12 During extended output-short conditions, excessive power dissipation occurs in the load switch. FPF2700 and PFP2701 are protected by turning off the load switch after blanking time. FPF2702 has no blanking time feature; please refer to Note 3. It is possible to estimate the SOA for the two FPF2702 packages, MPX and MX, through their respective SOA curves shown in Figure 39 and Figure 40. These curves provide a reference on how long the load switch survives under the worst-case scenario with minimum (1) pad size of one square inch. Figure 39. FPF2702 MPX SOA Figure 40. FPF2702 MX SOA Note: 3. To protect FPF2702 from an extended short condition, additional protection must be implemented in the system to protect the device. For example, the FLAGB and PGOOD signal can be used to monitor the short-circuit fault condition. In applications where FPF2702 can be exposed to persistent short-circuit conditions, it should be used only with external fault management control to protect the switch. (c) 2010 Fairchild Semiconductor Corporation FPF2700 / FPF2701 / FPF2702 * Rev. 1.0.3 FPF2700 / FPF2701 / FPF2702 -- AccuPowerTM 0.4~2A Adjustable Over-Current Protection Load Switches SOA (FPF2702) www.fairchildsemi.com 13 Power Dissipation To limit the voltage drop on the input supply caused by transient inrush currents when the switch is turned on into a discharged load capacitor or short-circuit; an input capacitor, CIN, is recommended between the IN and GND pins. The FPF270X features a fast current limit response time (50 s). During this period, the device relies on the input capacitor to supply the load current. A 10 F to 100 F ceramic capacitor is adequate for CIN in most cases. Larger CIN values may be required in highvoltage or high-current applications. An electrolytic capacitor can be used in parallel to further reduce the voltage drop. During normal operation as a switch, the power dissipation of the device is small and has little effect on the operating temperature of the part. The maximum power dissipation for the switch in normal operation occurs just before the switch enters into current limit. This may be calculated using the equation: PD _ MAX( NormalOper ation) ( I LIM( Max ) )2 RON ( MAX ) The maximum junction temperature should be limited to 125C under normal operation. Junction temperature can be calculated using the equation: Output Capacitor TJ PD JA TA A 0.1 F to 1 F capacitor, C OUT , should be placed between the OUT and GND pins. This capacitor helps prevent parasitic board inductances from forcing the output voltage below ground when the switch turns off. This capacitor should have a low dissipation factor. An X7R Multilayer Ceramic Chip (MLCC) capacitor is recommended. where: During startup, the total output current consists of both the load current and the charge current of the output capacitor. For the FPF2700 and FPF2701; if the total output current exceeds the set current limit threshold (determined via RSET) for longer than the blanking time, the device may not be able to start properly. This imposes an upper limit to the value of the output capacitor, given the load current and the selected current limit value. COUT should not exceed the COUTmax calculated in Equation 2 or the switch does not start properly due to the set current limit: COUT max ILIM _ MIN 500s / V PD _ MAX( NormalOper ation)( VIN12V ) (1 )2 0.140 140 mW If device is in over-current condition and VOUT>2 V, power dissipation can be calculated as: 22 27< VIN 32 47 32< VIN 36 68 (c) 2010 Fairchild Semiconductor Corporation FPF2700 / FPF2701 / FPF2702 * Rev. 1.0.3 (6) PD = (VIN - VOUT) x ILIM (Max) If device is in short-circuit current limit and VOUT < 2 V, power dissipation can be calculated as: (7) PD = (VIN - VOUT) x (0.75 x ILIM (Max) ) Design Example: Using FPF2702 in a VIN = 5 V application where ILIM (Max) = 2 A, assuming VOUT = 2.5 V; power dissipation across the switch is calculated as: PD = (5 - 2.5) x 2 = 5W COUT Selection Guide 24< VIN 27 (5) FPF2702 PD(Max) during OC: During a hard short condition on the output while operating at greater than 24 V VIN, a large instantaneous inrush current is delivered to the shorted output. A capacitor must be placed at the OUTPUT pin, acting as a current source to support the instantaneous current draw (Table 2). A low-ESR capacitor is recommended. Once the value of the output capacitor is determined from Table 2, Equation 2 must be reevaluated. Capacitance (F) TJ is junction temperature; PD is power dissipation on the switch; JA is the thermal resistance, junction-to-ambient of the package; and TA is ambient temperature. For a 12 V application and ILIM (Max) = 1 A, maximum power dissipation in a normal operation is calculated as: (2) VIN (V) (4) Design Example High-Voltage Operation (Output Capacitor) Table 2. (3) (8) Whereas in a short-circuit current-limit condition (VOUT 0 V), power dissipation is calculated as: PD = ((VIN - VOUT) x (0.75 x ILIM (Max)) = (5 - 0) x (0.75 x 2) = 7.5W (9) FPF2700 / FPF2701 / FPF2702 -- AccuPowerTM 0.4~2A Adjustable Over-Current Protection Load Switches Input Capacitor www.fairchildsemi.com 14 For the best performance, all traces should be as short as possible. To be most effective, the input and output capacitors should be placed close to the device to minimize the effects that parasitic trace inductances may have on normal and short-circuit operation (Figure 42). Using wide traces for IN, OUT, and GND pins helps minimize parasitic electrical effects as well as the caseto-ambient thermal impedance. 3. The IN, OUT, and GND pins dissipate most of the heat generated during high-load current condition. The layout suggested in Figure 42 and Figure 43 is strongly recommended illustrating a proper layout for devices in MLP 3x3 packages. IN, OUT, and GND pins are connected to adequate copper so that heat may be transferred as efficiently as possible out of the device. The low-power FLAGB and ON pins traces may be laid-out diagonally from the device to maximize the area available to the ground pad. Place the input and output capacitors as close as possible to the device. To minimize the interference between analog ground (chip ground, pin 5) and power ground during load current excursion, the ground terminal of the input and output capacitors and the RSET resistor should be routed directly to chip ground and away from power ground. Improving Thermal Performance Improper layout could result in higher junction temperature and trigger thermal shutdown protection. This is particularly significant for the FPF2702, where the device operates in Constant Current Mode under overload conditions. During fault conditions, the power dissipation of the switch could exceed the maximum absolute power dissipation. The following techniques improve the thermal performance of this family of devices. These techniques are listed in order of the significance of their impact. 1. Thermal performance of the load switch can be improved by connecting the Die Attach Pad (DAP) of the MLP 3x3 package to the GND plane of the PCB. Figure 42. Proper Layout of Output and Ground Copper Area (Top, SST, and AST Layers) 2. Embedding two exposed through-hole vias into the DAP provides a path for heat to transfer to the back GND plane of the PCB. A drill size of round, 15 mils (0.4 mm) with 1-ounce copper plating is recommended for appropriate solder reflow. A smaller-size hole prevents the solder from penetrating into the via, resulting in device lift-up. Similarly, a larger hole consumes excessive solder and may result in voiding the DAP. 15 Mil Figure 43. Proper Layout (Bottom and ASB Layers) 25 Mil Figure 41. Two Through-Hole Open Vias Embedded in the DAP (c) 2010 Fairchild Semiconductor Corporation FPF2700 / FPF2701 / FPF2702 * Rev. 1.0.3 FPF2700 / FPF2701 / FPF2702 -- AccuPowerTM 0.4~2A Adjustable Over-Current Protection Load Switches PCB Layout Recommendations www.fairchildsemi.com 15 The FPF270X demonstration board has components and circuitry to demonstrate the load switch's functions and features. Thermal performance of the board is improved using the techniques recommended in the layout recommendations section. Additional information about demonstration board can be found in the FPF270X board users guide. Figure 44. Top, SST, and AST Layers Figure 45. Bottom and ASB Layers (c) 2010 Fairchild Semiconductor Corporation FPF2700 / FPF2701 / FPF2702 * Rev. 1.0.3 FPF2700 / FPF2701 / FPF2702 -- AccuPowerTM 0.4~2A Adjustable Over-Current Protection Load Switches FPF270x Demonstration Board www.fairchildsemi.com 16 0.65 A 4.900.10 (0.635) 8 5 B 1.75 6.000.20 1 PIN ONE INDICATOR 5.60 3.900.10 4 1.27 1.27 0.25 C B A LAND PATTERN RECOMMENDATION SEE DETAIL A 0.1750.75 0.220.30 C 1.75 MAX 0.10 0.420.09 OPTION A - BEVEL EDGE (0.86) x 45 R0.10 GAGE PLANE R0.10 OPTION B - NO BEVEL EDGE 0.36 NOTES: UNLESS OTHERWISE SPECIFIED 8 0 A) THIS PACKAGE CONFORMS TO JEDEC MS-012, VARIATION AA. B) ALL DIMENSIONS ARE IN MILLIMETERS. C) DIMENSIONS DO NOT INCLUDE MOLD FLASH OR BURRS. D) LANDPATTERN STANDARD: SOIC127P600X175-8M. E) DRAWING FILENAME: M08Arev15 F) FAIRCHILD SEMICONDUCTOR. SEATING PLANE 0.650.25 (1.04) DETAIL A SCALE: 2:1 Figure 46. 8-Lead, Small Outline Package (SOP) Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner without notice. Please note the revision and/or date on the drawing and contact a Fairchild Semiconductor representative to verify or obtain the most recent revision. Package specifications do not expand the terms of Fairchild's worldwide terms and conditions, specifically the warranty therein, which covers Fairchild products. FPF2700 / FPF2701 / FPF2702 -- AccuPowerTM 0.4~2A Adjustable Over-Current Protection Load Switches Physical Dimensions Always visit Fairchild Semiconductor's online packaging area for the most recent package drawings: http://www.fairchildsemi.com/dwg/M0/M08A.pdf. (c) 2010 Fairchild Semiconductor Corporation FPF2700 / FPF2701 / FPF2702 * Rev. 1.0.3 www.fairchildsemi.com 17 3.00 0.15 C A 2X 2.52 B 8 3.00 5 1.94 1.70 3.30 PIN1 IDENT 0.56 8X 0.15 C TOP VIEW 1 2X 0.65 4 0.47 8X RECOMMENDED LAND PATTERN 0.80 MAX 0.10 C (0.20) 0.08 C 0.05 0.00 NOTES: C SIDE VIEW A. PACKAGE CONFORMS TO JEDEC MO-229 EXCEPT WHERE NOTED. SEATING PLANE B. DIMENSIONS ARE IN MILLIMETERS. C. DIMENSIONS AND TOLERANCES PER ASME Y14.5M, 1994. 2.45 2.35 PIN 1 IDENT 1 (0.35) 4X D. LAND PATTERN RECOMMENDATION IS BASED ON FSC DESIGN ONLY. E. DRAWING FILENAME: MKT-MLP08Vrev1. 4 1.75 1.65 0.40 8X 0.30 8 0.10 0.05 5 0.65 C A B C 0.40 8X 0.30 BOTTOM VIEW Figure 47. 8-Lead, 3x3 mm Molded Leadless Package (MLP) FPF2700 / FPF2701 / FPF2702 -- AccuPowerTM 0.4~2A Adjustable Over-Current Protection Load Switches Physical Dimensions Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner without notice. Please note the revision and/or date on the drawing and contact a Fairchild Semiconductor representative to verify or obtain the most recent revision. Package specifications do not expand the terms of Fairchild's worldwide terms and conditions, specifically the warranty therein, which covers Fairchild products. Always visit Fairchild Semiconductor's online packaging area for the most recent package drawings: http://www.fairchildsemi.com/dwg/ML/MLP08V.pdf. (c) 2010 Fairchild Semiconductor Corporation FPF2700 / FPF2701 / FPF2702 * Rev. 1.0.3 www.fairchildsemi.com 18 FPF2700 / FPF2701 / FPF2702 -- AccuPowerTM 0.4~2A Adjustable Over-Current Protection Load Switches (c) 2010 Fairchild Semiconductor Corporation FPF2700 / FPF2701 / FPF2702 * Rev. 1.0.3 www.fairchildsemi.com 19 ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor's product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by ON Semiconductor. "Typical" parameters which may be provided in ON Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor 19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com (c) Semiconductor Components Industries, LLC N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5817-1050 www.onsemi.com 1 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative www.onsemi.com