MODELS LPC-2516 and LPC-3019 VEEEy Inductors DALE, Surface Mount FEATURES * Totally integrated manufacturing * Excelient coplanarity &. * Pick and place compatible * Low DCR vs inductance * Statistical process controlled * Solderless wire bond ' * Tape packaging per ElA-481 APPLICATIONS e % * Low cost Circuit: Signal conditioning, filtering and ) * Qualification data available DC/DC converters. - UL Class H materials (180C) Equipment: Notebook computers, pagers and all types of battery powered equipment. * Wide inductance range STANDARD ELECTRICAL SPECIFICATIONS | os Pe - DCR RATED DC* MIN DCR RATED DC* CORE IND. Q MAX. CURRENT CORE IND. Q MAX. CURRENT MODEL TYPE (uH) MIN. (Ohms) (mA) MODEL TYPE (uH) MIN. (Ohms) (ma) LPC-2516 A 47 40 0.40 10 LPC-3019 A 150 40 0.30 10 68 40 0.50 10 220 40 0.40 10 100 50 0.80 10 330 40 0.60 10 150 50 0.90 10 470 40 0.70 10 220 50 1.10 10 680 40 0.80 10 330 50 2.00 10 1000 40 1.00 10 470 50 2.30 10 1500 50 1.80 10 680 50 3.00 10 2200 50 3.50 7 1000 50 6.50 10 3300 50 4.00 7 1500 60 8.00 7 4700 50 4.50 7 2200 60 10.0 7 6800 50 5.00 7 3300 60 12.0 7 . _ _ 4700 60 15.0 7 Rated DC current is based on a 25% reduction in the minimum inductance value. ELECTRICAL SPECIFICATIONS Inductance - L and Quality Factor -Q: Measured with Maximum Operating Voltage: 2.5 V RMS to 10 V RMS, H/P 4284A impedance analyzer at 50 mV RMS, 100kHz. depending on inductance value. DC Resistance - DCR: Measured with H/P 34401A Operating Temperature Range: - 25C to + 60C. multimeter, or equivalent chmmeter at + 25C + 5C. te milieneters] LPC-3019 ~~ 060 + .005 [0.27 #127] [1.52 +127] .070 (1.78}_| | V Wrap-Around .080 [2.03 Wrap-Around REF. Termination ne 1_,| |. Ter ination .200 [5.08] 110 [2.79] + MAX. MAX. CT Y poo .025 [.635] REF. 4 4 5 .025 [.635} REF. .250 +.010 ~< 300.010 ~ 16.35 2.254) [7.62 + .254] 050 + .005 > Lg 040 + 005 - < 14.97 + 127] [1.02 +.127] 27s. 160 [4.06] whe see eon DRALORIC ELECTRONIC GMBH, Geheimrat-Rosenthal-Sir. 100, 95100 Selb, Germany Tel: (0)9287/710 + Fax: (0}9287/70435 247MODELS LPC-2516 and LPC-3019 TEST CONDITION/METHOD SPECIFICATIONS Thermal Shock (air to air), Unmounted Ten cycles of 30 minutes @ - 55C, 15 seconds maximum @ room ambient, 30 minutes @ + 125C, 15 seconds maximum @ room ambient. All mechanical and electrical degradation limits apply. Moisture Resistance Precondition at + 40C for 60 minutes. Subject the component to 240 hours at + 40C and 90 to 95% relative humidity. All mechanical and electrical degradation limits apply. Storage Life Subject the component to 168 hours at + 85C and 85% relative humidity. All mechanical and electrical degradation limits apply. Resistance to Soldering Heat Mount to PC Board Reflow Cycle Expose components to an IR solder reflow environment with IR heating at a temperature of + 200C for 300 + 10 seconds with an included + 230C peak temperature for 30 seconds minimum. All mechanical and electrical degradation limits apply. Mechanical Shock One-half sine pulse (8700 G's for 0.3 milliseconds) in each direction along 3 mutually perpendicular axes in each direction (total of 6 shocks). All mechanical and electrical degradation limits apply. Vibration 1 cycle of 30 minutes duration per the following: 5-7 Hz constant displacement of 1.0 inch, 5 minutes, 7-30 Hz constant acceleration of 1.5 G's, 10 minutes, 30-50 Hz constant displacement of 0.033 inch, 5 minutes, 50-500 Hz constant acceleration of 4.2 G's, 10 minutes. All mechanical and electrical degradation limits apply. Resistance to Solvents, Forced spray environment of Terpene at + 25 C and 3 minutes All mechanical and electrical degradation and pads are dipped 30 from vertical. Solder temperature: + 245C + 5C. Immersion dwell time: 5 + 1/2 seconds. Terpene of water rinse at + 70C and 2 minutes of forced I.R. drying at limits apply. + 120C. Solderability Per MIL-STD-202, Method 208, except steam aging is omitted Board contact area of pads will exhibit minimum of 80% wetting coverage. All mechanical and electrical degradation limits apply. NOTE: All specified characteristics verified by quaiification testing at Dale Electronics. Inc., or customer test facilities. Carrier Tape Type: Non-conductive. Cover Tape Type: Anti-static. Cover Tape Adhesion to Carrier: 60-175 grams. REEL SPECIFICATIONS: Antistatic. Diameter (flange): 13" (330.2 mm]. Reel width is maximum measured over flange. HOWTOORDER LPC 2516 1000.H A MODEL SIZE INDUCTANCE VALUE CORE PACKAGING _ ws ee bore TAPE SPECIFICATIONS: STANDARDS: All embossed carrier tape packaging will be accomplished in compliance with latest revision of EIA-481 "Taping of Surface Mount Components for Automatic Placement. TAPE REEL COMPONENT UNITS MODEL WIDTH WIDTH PITCH PER REEL LPC-2516 12mm 18.4mm 8mm 2500 LPC-3019 16mm 22.4mm 8mm 2500 Tape and Reel Orientation USER DIRECTION OF FEED NOTE: Top view shown with cover tape removed. xO Cover Tape Carrier Tape Label Area DRALORIC ELECTRONIC GMBH, Geheimrat-Rosenthal-Str. 100, 95100 Selb, Germany * Tel: (0)9287/710 * Fax: (0)9287/70435 248