LTC2904/LTC2905 Precision Dual Supply Monitors with Pin-Selectable Thresholds DESCRIPTION FEATURES n n n n n n n n n n n Monitors Two Inputs Simultaneously Nine Threshold Combinations Three Supply Tolerances (5%, 7.5%, 10%) Guaranteed Threshold Accuracy: 1.5% of Monitored Voltage Over Temperature Internal VCC Auto Select Power Supply Glitch Immunity 200ms Reset Time Delay (LTC2904 Only) Adjustable Reset Time Delay (LTC2905 Only) Open Drain RST Output Guaranteed RST for V1 1V or V2 1V Low Profile (1mm) SOT-23 (ThinSOTTM) and Plastic (3mm x 2mm) DFN Packages The LTC(R)2904/LTC2905 are dual supply monitors intended for systems with two supply voltages. The dual supply monitors have a common reset output with delay (200ms for the LTC2904 and adjustable using an external capacitor for the LTC2905). This product provides a precise, space-conscious and micropower solution for supply monitoring. The LTC2904/LTC2905 feature a tight 1.5% threshold accuracy over the whole operating temperature range, and glitch immunity to ensure reliable reset operation without false triggering. The open drain RST output is guaranteed to be in the correct state for inputs down to 1V. APPLICATIONS n n n n Desktop and Notebook Computers Handheld Devices Network Servers Core, I/O Monitor L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks of Linear Technology Corporation. ThinSOT is a trademark of Linear Technology Corporation. All other trademarks are the property of their respective owners. The LTC2904/LTC2905 also feature three programming input pins, which program the threshold and tolerance level without requiring any external components. These three programming pins provide a total of 27 different voltage level and tolerance combinations, eliminating the need to have different parts for development and implementation of different systems with different voltage levels requiring monitoring function. TYPICAL APPLICATION 5V, 3.3V Dual Supply Monitor with 5% Tolerance Table 1. Voltage Threshold Programming 5V DC/DC CONVERTER SYSTEM LOGIC 3.3V V1 V2 LTC2905 0.1F 0.1F S1 TMR S2 GND TOL RST 22nF 29045 TA01 V1 V2 S1 S2 5.0 3.3 V1 V1 3.3 2.5 Open GND 3.3 1.8 V1 Open 3.3 1.5 Open V1 3.3 1.2 Open Open 2.5 1.8 GND GND 2.5 1.5 GND Open 2.5 1.2 GND V1 2.5 1.0 V1 GND 29045fd 1 LTC2904/LTC2905 ABSOLUTE MAXIMUM RATINGS (Note 1, 2) Terminal Voltages V1, V2 ...................................................... -0.3V to 7V S1, S2, TOL ................................-0.3V to (VCC +0.3V) RST .......................................................... -0.3V to 7V RST (LTC2904) ........................................ -0.3V to 7V TMR (LTC2905) ....................................... -0.3V to 7V Operating Temperature Range LTC2904C/LTC2905C .............................. 0C to 70C LTC2904I/LTC2905I.............................-40C to 85C LTC2905H .......................................... -40C to 125C Storage Temperature Range .................. -65C to 150C TSOT Lead Temperature (Soldering, 10 sec) ......... 300C PIN CONFIGURATION TOP VIEW GND 1 RST 2 8 TOL 7 S1 RST/TMR* 3 6 S2 V2 4 5 V1 9 TOP VIEW V2 1 RST/TMR* 2 RST 3 GND 4 8 V1 7 S2 6 S1 5 TOL TS8 PACKAGE 8-LEAD PLASTIC TSOT-23 * RST FOR LTC2904 TMR FOR LTC2905 TJMAX = 150C, JA = 195C/W DDB8 PACKAGE 8-LEAD (3mm s 2mm) PLASTIC DFN EXPOSED PAD IS GND (PIN 9), MUST BE SOLDERED TO PCB * RST FOR LTC2904 TMR FOR LTC2905 TJMAX = 150C, JA = 76C/W ORDER INFORMATION Lead Free Finish TAPE AND REEL (MINI) TAPE AND REEL PART MARKING* PACKAGE DESCRIPTION TEMPERATURE RANGE LTC2904CDDB#TRMPBF LTC2904CDDB#TRPBF LBCZ 8-Lead (3mm x 2mm) Plastic DFN 0C to 70C LTC2904IDDB#TRMPBF LTC2904IDDB#TRPBF LBDB 8-Lead (3mm x 2mm) Plastic DFN -40C to 85C LTC2905CDDB#TRMPBF LTC2905CDDB#TRPBF LAJF 8-Lead (3mm x 2mm) Plastic DFN 0C to 70C LTC2905HDDB#TRMPBF LTC2905HDDB#TRPBF LBCY 8-Lead (3mm x 2mm) Plastic DFN -40C to 125C LTC2905IDDB#TRMPBF LTC2905IDDB#TRPBF LBCY 8-Lead (3mm x 2mm) Plastic DFN -40C to 85C LTC2904CTS8#TRMPBF LTC2904CTS8#TRPBF LTBCJ 8-Lead Plastic TSOT-23 0C to 70C LTC2904ITS8#TRMPBF LTC2904ITS8#TRPBF LTBCK 8-Lead Plastic TSOT-23 -40C to 85C LTC2905CTS8#TRMPBF LTC2905CTS8#TRPBF LTAJD 8-Lead Plastic TSOT-23 0C to 70C LTC2905HTS8#TRMPBF LTC2905HTS8#TRPBF LTAJE 8-Lead Plastic TSOT-23 -40C to 125C LTC2905ITS8#TRMPBF LTC2905ITS8#TRPBF LTAJE 8-Lead Plastic TSOT-23 TRM = 500 pieces. *Temperature grades are identified by a label on the shipping container. Consult LTC Marketing for parts specified with wider operating temperature ranges. Consult LTC Marketing for information on lead based finish parts. For more information on lead free part marking, go to: http://www.linear.com/leadfree/ For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/ -40C to 85C 29045fd 2 LTC2904/LTC2905 ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. V1 = 2.5V, V2 = 1V, S1 = TOL = V1, S2 = 0V, unless otherwise noted. (Notes 2, 3) SYMBOL VRT50 CONDITIONS V1 Input Threshold VCCMIN IV1 IV2 PARAMETER 5V, 5% Reset Threshold 5V, 7.5% Reset Threshold 5V, 10% Reset Threshold 3.3V, 5% Reset Threshold 3.3V, 7.5% Reset Threshold 3.3V, 10% Reset Threshold 2.5V, 5% Reset Threshold 2.5V, 7.5% Reset Threshold 2.5V, 10% Reset Threshold 1.8V, 5% Reset Threshold 1.8V, 7.5% Reset Threshold 1.8V, 10% Reset Threshold 1.5V, 5% Reset Threshold 1.5V, 7.5% Reset Threshold 1.5V, 10% Reset Threshold 1.2V, 5% Reset Threshold 1.2V, 7.5% Reset Threshold 1.2V, 10% Reset Threshold 1V, 5% Reset Threshold 1V, 7.5% Reset Threshold 1V, 10% Reset Threshold Minimum Internal Operating Voltage (Note 2) V1 Input Current V2 Input Current ITMR(UP) ITMR(DOWN) TMR Pull-Up Current TMR Pull-Down Current VTMR = 0V VTMR = 1.4V tRST Reset Timeout Period LTC2905 LTC2905 LTC2905H LTC2904 tRST Reset Timeout Period LTC2905 LTC2905H CTMR = 22nF tUV Vx Undervoltage Detect to RST or RST Output Voltage Low RST, RST VRT33 VRT25 VRT18 VRT15 VRT12 VRT10 VOL Output Voltage High RST, RST (Notes 2, 5) Three-State Inputs S1, S2, TOL VIL Low Level Input Voltage VIH High Level Input Voltage VZ Pin Voltage When Left in Open State VOH 2905H IVPG Programming Input Current (Note 6) 65 0.4 MAX 4.750 4.625 4.500 3.135 3.053 2.970 2.375 2.313 2.250 1.710 1.665 1.620 1.425 1.388 1.350 1.140 1.110 1.080 0.950 0.925 0.900 1 130 1.0 UNITS V V V V V V V V V V V V V V V V V V V V V V A A l -1.5 1.5 1.4 140 -2.1 2.1 2.0 200 -2.7 2.7 2.7 260 A A A ms l l 140 140 200 260 295 ms ms s 0.4 0.3 V V V 0.4 V V V V V V V V A l l l V1, V2 Input Threshold l l l V1, V2 Input Threshold l l l V2 Input Threshold l l l V2 Input Threshold l l l V2 Input Threshold l l l V2 Input Threshold l l l RST in Correct Logic State Includes Input Current to Three-State Pins l MIN 4.600 4.475 4.350 3.036 2.954 2.871 2.300 2.238 2.175 1.656 1.611 1.566 1.380 1.343 1.305 1.104 1.074 1.044 0.920 0.895 0.870 l l Vx Less than Reset Threshold VRTX by More than 1% I = 2.5mA I = 100A; V1 = 1V (RST Only) I = -1A l l l TYP 4.675 4.550 4.425 3.086 3.003 2.921 2.338 2.275 2.213 1.683 1.638 1.593 1.403 1.365 1.328 1.122 1.092 1.062 0.935 0.910 0.885 150 l l l 0.15 0.05 VCC-1 l l I = -10A I = 0A I = 10A I = -10A I = 0A I = 10A l 1.4 0.7 0.9 l l l l 1.1 0.65 0.9 1.15 25 29045fd 3 LTC2904/LTC2905 ELECTRICAL CHARACTERISTICS Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: The greater of V1, V2 is the internal supply voltage (VCC). Note 3: All currents into pins are positive; all voltages are referenced to GND unless otherwise noted. Note 4: For reset thresholds test conditions refer to the voltage threshold programming table in the Applications Information section. Note 5: The output pins RST and RST have an internal pull-up to VCC of typically -6A. However, an external pull-up resistor may be used when faster rise time is required or for VOH voltages greater than VCC. Note 6: The input current to the three-state input pins are the pull-up and the pull-down current when the pins are either set to V1 or GND respectively. In the open state, the maximum leakage current to V1 or GND permissible is 10A. TYPICAL PERFORMANCE CHARACTERISTICS Specifications are at TA = 25C unless otherwise noted. 5V Threshold Voltage vs Temperature 3.3V Threshold Voltage vs Temperature 4.75 2.5V Threshold Voltage vs Temperature 2.375 3.120 5% 4.65 4.60 7.5% 4.55 4.50 4.45 10% 4.40 4.35 -50 -25 25 50 0 TEMPERATURE (oC) 75 3.070 7.5% 3.020 2.970 10% 2.920 2.870 -50 100 THRESHOLD VOLTAGE, VRT25 (V) 4.70 THRESHOLD VOLTAGE, VRT33 (V) THRESHOLD VOLTAGE, VRT50 (V) 5% -25 25 50 0 TEMPERATURE (oC) 75 29045 G01 7.5% 2.275 2.175 -50 7.5% 1.645 1.625 1.605 10% 1.585 -25 25 50 0 TEMPERATURE (oC) 75 100 29045 G04 25 50 0 TEMPERATURE (oC) 1.135 1.125 5% 1.405 1.385 7.5% 1.365 1.345 10% 1.325 1.305 -50 100 75 1.2V Threshold Voltage vs Temperature THRESHOLD VOLTAGE, VRT12 (V) THRESHOLD VOLTAGE, VRT15 (V) 1.665 -25 29045 G03 1.425 5% 1.685 10% 2.225 1.5V Threshold Voltage vs Temperature 1.705 THRESHOLD VOLTAGE, VRT18 (V) 2.325 29045 G02 1.8V Threshold Voltage vs Temperature 1.565 -50 100 5% 5% 1.115 1.105 7.5% 1.095 1.085 1.075 1.065 10% 1.055 -25 25 50 0 TEMPERATURE (oC) 75 100 29045 G05 1.045 -50 -25 25 50 0 TEMPERATURE (oC) 75 100 29045 G06 29045fd 4 LTC2904/LTC2905 TYPICAL PERFORMANCE CHARACTERISTICS Specifications are at TA = 25C unless otherwise noted. 1V Threshold Voltage vs Temperature IV1 vs Temperature 0.940 1.8 V1 = 5V V2 = 3.3V S1 = S2 = TOL = 1.4V 5% 21.0 V1 = 5V V2 = 3.3V S1 = S2 = TOL = 1.4V 1.7 0.930 1.6 7.5% 0.910 0.900 20.5 IV2 (MA) 0.920 IV1 (MA) THRESHOLD VOLTAGE, VRT10 (V) IV2 vs Temperature 21.5 0.950 20.0 1.5 1.4 0.890 10% 19.5 1.3 0.880 0.870 -50 -25 25 50 0 TEMPERATURE (oC) 75 19.0 -50 100 -25 25 50 0 TEMPERATURE (oC) 75 29045 G07 700 IV2 (MA) 19.0 18.5 18.0 17.5 17.0 -50 25 50 0 TEMPERATURE (oC) 75 600 500 400 RESET OCCURS ABOVE CURVE 300 200 100 Reset Timeout Period (tRST) vs Temperature 215 210 205 50 75 100 4 3 2 1 -1 29045 G13 3 2 1 0 -1 0 1 2 3 4 5 0 1 2 3 4 5 V1 (V) V1 (V) TEMPERATURE (oC) 1M V2 = S1 = S2 = TOL = V1 10k PULL-UP RESISTOR 0 200 100n RST Output Voltage vs V1 RST OUTPUT VOLTAGE (V) RST OUTPUT VOLTAGE (V) RESET TIME-OUT PERIOD, tRST (ms) 220 1n 10n CTMR (FARAD) 5 4 225 100p 29045 G12 V2 = S1 = S2 = TOL = V1 10k PULL-UP RESISTOR 25 1 RST Output Voltage vs V1 CRT = 22nF 230 (FILM) 0 10 0.1 10p 5 235 -25 100 29045 G11 29045 G10 195 -50 1000 1 10 100 0.1 COMPARATOR OVERDRIVE VOLTAGE (% OF VRTX) 100 100 10000 0 -25 75 Reset Time Out Period (tRST) vs Capacitance (CTMR) RESET TIME OUT PERIOD, tRST (ms) TYPICAL TRANSIENT DURATION (Ms) 19.5 25 50 0 TEMPERATURE (oC) 29045 G09 Typical Transient Duration vs Comparator Overdrive (V1, V2) V1 = 2.5V V2 = 3.3V S1 = S2 = TOL = 1.4V -25 29045 G08 IV2 vs Temperature 20.0 1.2 -50 100 29045 G14 29045 G15 29045fd 5 LTC2904/LTC2905 TYPICAL PERFORMANCE CHARACTERISTICS Specifications are at TA = 25C unless otherwise noted. RST Pull-Down Current (IRST) vs Supply Voltage (VCC) RST Output Voltage vs V1 RST Pull-Down Current (IRST) vs Supply Voltage (VCC) 5 3 2 1 0 0 1 2 3 3 2 1 RST AT 50mV 0 5 4 RST AT 150mV V1 (V) 2 3 4 SUPPLY VOLTAGE, VCC (V) 29045 G16 RST OUTPUT VOLTAGE LOW, VOL (V) 1.6 1.4 25oC -40oC 1.2 1.0 0.8 0.6 0.4 0.2 0 10 30 40 50 20 RST PULL-DOWN CURRENT, IRST (mA) V1 = 5V V2 = 3.3V S1 = S2 = TOL = V1 NO PULL-UP R 1.6 1.4 1.2 0.6 0.4 0.2 3.0 -6 -4 -2 0 2.0 VRT25 2.5 VRT33 -16 -14 -12 -10 -8 -6 -4 -2 VRT25 VRT50 3.0 3.5 4.0 4.5 SUPPLY VOLTAGE, VCC (V) 5.0 29045 G22 VRT33 2.0 10 30 40 50 60 20 RST PULL-DOWN CURRENT, IRST (mA) 2.5 2.5 85oC -40oC 1.0 25oC 0.5 -12 5.0 29045 G21 RST Output Voltage High (VOH) vs RST Output Source Current (IRST) 3.5 V1 = 3.3V V2 = 1.8V S1 = TOL =V1 S2 = OPEN NO PULL-UP R 2.0 1.5 VRT50 3.0 3.5 4.0 4.5 SUPPLY VOLTAGE, VCC (V) 29045 G20 TOL = V1 -8 5 29045 G18 RST Output Voltage High (VOH) vs RST Output Source Current (IRST) -10 2 3 4 SUPPLY VOLTAGE, VCC (V) 0 0 RST OUTPUT VOLTAGE HIGH, VOH (V) RST PULL-UP CURRENT, IRST (MA) 25oC 0.8 RST Pull-Up Current (IRST) vs Supply Voltage (VCC) -12 1 0 TOL = GND 85oC 1.0 60 -14 RST AT 50mV RST Pull-Up Current (IRST) vs Supply Voltage (VCC) -40oC 29045 G19 -16 1 5 0 0 2 -18 1.8 85oC RST AT 150mV 3 RST Output Voltage Low (VOL) vs RST Pull-Down Current (IRST) RST OUTPUT VOLTAGE LOW, VOL (V) V1 = 5V V2 = 3V S1 = S2 = TOL = V1 NO PULL-UP R 4 29045 G17 RST Output Voltage Low (VOL) vs RST Pull-Down Current (IRST) 1.8 S1 = V2 = V1 TOL = S2 = GND NO PULL-UP R 5 0 1 0 RST PULL-UP CURRENT, IRST (MA) -1 4 RST OUTPUT VOLTAGE HIGH, VOH (V) RST OUTPUT VOLTAGE (V) 4 V2 = S1 = S2 = TOL = V1 NO PULL-UP R 5 RST PULL-DOWN CURRENT, IRST (mA) RST PULL-DOWN CURRENT, IRST (mA) V2 = S1 = S2 = TOL = V1 10pF CAPACITOR AT RST V1 = 3.3V V2 = 1.5V S1 = TOL = V1 S2 = OPEN NO PULL-UP R 3.0 2.5 2.0 -40oC 1.5 85oC 1.0 25oC 0.5 -8 -6 -4 -2 -10 OUTPUT SOURCE CURRENT, IRST (MA) 0 29045 G23 -8 -7 -6 -5 -4 -3 -2 -1 OUTPUT SOURCE CURRENT, IRST (MA) 0 29045 G24 29045fd 6 LTC2904/LTC2905 TYPICAL PERFORMANCE CHARACTERISTICS Specifications are at TA = 25C unless otherwise noted. IS1, IS2, ITOL vs Temperature IS1, IS2, ITOL vs Temperature -20 20 S1 = S2 = TOL = GND -19 18 -18 17 -17 IS1, IS2, ITOL (MA) IS1, IS2, ITOL (MA) S1 = S2 = TOL = 3.3V 19 16 15 14 13 -16 -15 -14 -13 12 -12 11 -11 10 -50 -25 25 50 0 TEMPERATURE (oC) 75 100 29045 G25 PIN FUNCTIONS -10 -50 -25 25 50 0 TEMPERATURE (oC) 75 100 29045 G26 (TS8/DDB8) V2 (Pin 1/Pin 4): Voltage Input 2. Input for V2 monitor. Select from 3.3V, 2.5V, 1.8V, 1.5V, 1.2V or 1.0V. Refer to Table 1 for details. The greater of V1, V2 is also the internal supply voltage, VCC. Bypass this pin to ground with a 0.1F (or greater) capacitor. RST (Pin 2/Pin 3): (LTC2904 Only) Reset Logic Output. When all voltage inputs are above the reset threshold for at least the programmed delay time, this pin pulls low. This pin has a weak pull-up to VCC and may be pulled above VCC using an external pull-up. TMR (Pin 2/Pin 3): (LTC2905 Only) Reset Delay Time Programming Pin. Attach an external capacitor (CTMR) to GND to set a reset delay time of 9ms/nF. Leaving the pin open generates a minimum delay of approximately 200s. A 22nF capacitor will generate a 200ms reset delay time. RST (Pin 3/Pin 2): Inverted Reset Logic Output. Pulls low when any voltage input is below the reset threshold and is held low for programmed delay time after all voltage inputs are above threshold. This pin has a weak pull-up to VCC and may be pulled above VCC using an external pull-up. GND (Pin 4/Pin 1, Pin 9): Ground. TOL (Pin 5/Pin 8): Three-state Input for Supply Tolerance Selection (5%, 7.5% or 10%). See the Applications Information section for tolerance selection chart (Table 2). S1 (Pin 6/Pin 7): Voltage Threshold Select Three-State Input. Connect to V1, GND or leave unconnected in open state (See Table 1). S2 (Pin 7/Pin 6): The Second Voltage Threshold Select Three-State Input. Connect to V1, GND or leave unconnected in open state (See Table 1). V1 (Pin 8/Pin 5): Voltage Input 1. Input for V1 monitor. Select from 5V, 3.3V, or 2.5V. See Table 1 for details. The greater of V1, V2 is also the internal supply voltage, VCC. Bypass this pin to ground with a 0.1F (or greater) capacitor. 29045fd 7 LTC2904/LTC2905 BLOCK DIAGRAM VCC LTC2904 6A - RST V1 + VCC POWER DETECT 200ms RESET PULSE GENERATOR RESISTOR NETWORK - VCC 6A V2 + RST BAND GAP REFERENCE THREE-STATE DECODER GND 2904 BD S1 S2 TOL LTC2905 - TMR VCC V1 + VCC POWER DETECT 6A RESISTOR NETWORK RESET PULSE GENERATOR - RST V2 + BAND GAP REFERENCE THREE-STATE DECODER GND 2905 BD S1 S2 TOL 29045fd 8 LTC2904/LTC2905 TIMING DIAGRAM VX Monitor Timing VRTX VX tUV tRST RST 1V RST 1V 29045 TD APPLICATIONS INFORMATION Supply Monitoring Power-Up The LTC2904/LTC2905 are low power, high accuracy dual supply monitors with a common reset output and selectable thresholds. Reset delay is set to a nominal of 200ms for the LTC2904 and is adjustable using an external capacitor for the LTC2905. The greater of V1, V2 is the internal supply voltage (VCC). VCC powers the drive circuits for the RST pin. Therefore as soon as V1 or V2 reaches 1V during power-up, the RST output asserts low. The two 3-state input pins (S1 and S2) select one of nine possible threshold voltage combinations. Another threestate input pin sets the supply tolerance (5%, 7.5% or 10%). Both input voltages (V1 and V2) must be above predetermined thresholds for the reset not to be invoked. The LTC2904/LTC2905 assert the reset outputs during power-up, power-down and brownout conditions on either of the voltage inputs. VCC also powers the drive circuits for the RST pin in the LTC2904. Therefore, RST weakly pulls high when V1 or V2 reaches at least 1V. Threshold programming is complete when V1 reaches at least 2.17V. After programming, if either V1 or V2 falls below its programmed threshold, RST asserts low (RST weakly pulls high) as long as VCC is at least 1V. Once V1 and V2 rise above their thresholds, an internal timer is started. After the programmed delay time, RST weakly pulls high (RST asserts low). 29045fd 9 LTC2904/LTC2905 APPLICATIONS INFORMATION Power-Down Tolerance Programming On power-down, once either V1 or V2 inputs drops below its threshold, RST asserts logic low and RST weakly pulls high. VCC of at least 1V guarantees a logic low of 0.4V at RST. The three-state input pin, TOL programs the common supply tolerance for both V1 and V2 input voltages (5%, 7.5% or 10%). The larger the tolerance the lower the trip threshold. Table 2 shows the tolerances selection corresponding to a particular connection at the TOL pin. Programming Pins The three 3-state input pins: S1, S2 and TOL should be connected to GND, V1 or left unconnected during normal operation. Note that when left unconnected, the maximum leakage current allowable from the pin to either GND or V1 is 10A. In margining applications, all the 3-state input pins can be driven using a tri-state buffer. Note however the low and high output of the tri-state buffer has to satisfy the VIL and VIH of the 3-state pin listed in the Electrical Characteristics Table. Moreover, when the tri-state buffer is in the high impedance state, the maximum leakage current allowed from the pin to either GND or V1 is 10A. Monitor Programming Connecting S1 and S2 to GND, V1 or leaving them open selects the LTC2904/LTC2905 input voltage combinations. Table 1 shows the nine possible combinations of nominal input voltages and their corresponding S1, S2 connections. Table 1. Voltage Threshold Programming V1 V2 S1 S2 5.0 3.3 V1 V1 3.3 2.5 Open GND 3.3 1.8 V1 Open 3.3 1.5 Open V1 3.3 1.2 Open Open 2.5 1.8 GND GND 2.5 1.5 GND Open 2.5 1.2 GND V1 2.5 1.0 V1 GND Table 2. Tolerance Programming Tolerance TOL 5% V1 7.5% Open 10% GND Threshold Accuracy Reset threshold accuracy is of the utmost importance in a supply sensitive system. Ideally such a system should not reset while supply voltages are within a specified margin below the rated nominal level. Both of the LTC2904/LTC2905 inputs have the same relative threshold accuracy. The specification for LTC2904/LTC2905 is 1.5% of the programmed nominal input voltage (over the full operating temperature range). For example, when the LTC2904/LTC2905 are programmed to handle a 5V input with 10% tolerance (S1 = S2 = V1 and TOL = GND, refer to Table 1 and Table 2), it does not issue a reset command when V1 is above 4.5V. The typical 10% trip threshold is at 11.5% below the nominal input voltage level. Therefore, the typical trip threshold for the 5V input is 4.425V. With 1.5% accuracy, the trip threshold range is 4.425V 75mV over temperature (i.e. 10% to 13% below 5V). This implies that the monitored system must operate reliably down to 4.35V over temperature. The same system using a supervisor with only 2.5% accuracy needs to work reliably down to 4.25V (4.375V 125mV) or 15% below 5V, requiring the monitored system to work over a much wider operating voltage range. Note: Open = open circuit or driven by a three state buffer in high impedance state with leakage current less than 10A. 29045fd 10 LTC2904/LTC2905 APPLICATIONS INFORMATION The LTC2904/LTC2905 takes a different approach to solve this problem of supply noise causing spurious reset. The first line of defense against this spurious reset is a first order low pass filter at the output of the comparator. Thus, the comparator output goes through a form of integration before triggering the output logic. Therefore, any kind of transient at the input of the comparator needs to be of sufficient magnitude and duration before it can trigger a change in the output logic. The second line of defense is the programmed delay time tRST (200ms for LTC2904 and using an external capacitor for LTC2905). This delay will eliminate the effect of any supply noise whose frequency is above 1/tRST on the RST and RST output. When either V1 or V2 drops below its programmed threshold, the RST pin asserts low (RST weakly pulls high). Then when the supply recovers above the programmed threshold, the reset-pulse-generator timer starts counting. If the supply remains above the programmed threshold when the timer finishes counting, the RST pin weakly pulls high (RST asserts low). However, if the supply falls below the programmed threshold any time during the period when the timer is still counting, the timer resets and it starts fresh when the supply next rises above the programmed threshold. Selecting the Reset Timing Capacitor The reset timeout period for LTC2905 is adjustable in order to accommodate a variety of microprocessor applications. Connecting a capacitor, CTMR, between the TMR pin and ground sets the reset timeout period, tRST. The following formula determines the value of capacitor needed for a particular reset timeout period: CTMR = tRST * 110 * 10-9 [F/s] For example, using a standard capacitor value of 22nF would give a 22000/110 = 200ms delay. Figure 1 shows the desired delay time as a function of the value of the timer capacitor that should be used: Leaving the TMR pin open with no external capacitor generates a reset timeout of approximately 200s. For long reset timeout, the only limitation is the availability of large value capacitor with low leakage. The TMR capacitor will never charge if the leakage current exceeds the minimum TMR charging current of 2.1A (typical). 10000 RESET TIME OUT PERIOD, tRST (ms) In any supervisory application, supply noise riding on the monitored DC voltage can cause spurious resets, particularly when the monitored voltage is near the reset threshold. A less desirable but common solution to this problem is to introduce hysteresis around the nominal threshold. Notice however, this hysteresis introduces an error term in the threshold accuracy. Therefore, a 2.5% accurate monitor with 1.0% hysteresis is equivalent to a 3.5% monitor with no hysteresis. 1000 100 10 1 0.1 10p 100p 1n 10n CTMR (FARAD) 100n 1 29045 F01 Figure 1. Reset Timeout Period vs Capacitance Note that this second line of defense is only effective for a rising supply and does not affect the sensitivity of the system to a falling supply. Therefore, the first line of defense that works for both cases of rising and falling is necessary. These two approaches prevent spurious reset caused by supply noise without sacrificing the threshold accuracy. 29045fd 11 LTC2904/LTC2905 APPLICATIONS INFORMATION RST and RST Output Characteristics Output Rise and Fall Time Estimation The DC characteristics of the RST and RST pull-up and pull-down strength are shown in the Typical Performance Characteristics section. Both RST and RST have a weak internal pull-up to VCC = Max (V1, V2) and a strong pulldown to ground. The RST and RST outputs have strong pull-down capability. The following formula estimates the output fall time (90% to 10%) for a particular external load capacitance (CLOAD): The weak pull-up and strong pull-down arrangement allow these two pins to have open-drain behavior while possessing several other beneficial characteristics. The weak pull-ups eliminate the need for external pull-up resistors when the rise time on these pins is not critical. On the other hand, the open-drain RST configuration allows for wired-OR connections and can be useful when more than one signal needs to pull down on the RST line. As noted in the Power-Up and Power-Down sections the circuits that drive RST and RST are powered by VCC. During fault condition, VCC of at least 1V guarantees a maximum VOL = 0.4V at RST. However, at VCC = 1V the weak pull-up current on RST is barely turned on. Therefore, an external pull-up resistor of no more than 100k is recommended on the RST pin if the state and pull-up strength of the RST pin is crucial at very low VCC. Note however, by adding an external pull-up resistor, the pull-up strength on the RST pin is increased. Therefore, if it is connected in a wired-OR connection, the pull-down strength of any single device needs to accommodate this additional pull-up strength. tFALL 2.2 * RPD * CLOAD where RPD is the on-resistance of the internal pull-down transistor estimated to be typically 40 at room temperature (25C) and CLOAD is the external load capacitance on the pin. Assuming a 150pF load capacitance, the fall time is about 13ns. The rise time, on the RST and RST pins is limited by weak internal pull-up current sources to VCC. The following formula estimates the output rise time (10% to 90%) at the RST and RST pins: tRISE 2.2 RPU * CLOAD where RPU is the on-resistance of the pull-up transistor. Notice that this pull-up transistor is modeled as a 6A current source in the Block Diagram as a typical representation. The on-resistance as a function of the VCC = Max (V1, V2) voltage (for VCC > 1V) at room temperature is estimated as follows: R PU = 6 * 105 MAX( V1,V2) - 1V At VCC = 3.3V, RPU is about 260k. Using 150pF for load capacitance, the rise time is 86s. An external pull-up resistor may be used if the output needs to pull up faster and/or to a higher voltage, for example: the rise time reduces to 3.3s for a 150pF load capacitance, when using a 10k pull-up resistor. 29045fd 12 LTC2904/LTC2905 TYPICAL APPLICATIONS 2.5V, 1.2V Supply Monitor, 10% Tolerance 3.3V, 1.2V Dual Supply Monitor with LED Power Good Indicator, 7.5% Tolerance and Adjustable Timer 3.3V 510 V2 1.2V V1 2.5V V2 1.2V LTC2904 LTC2904 RST S2 RST S1 GND TOL 0.1F 0.1F SYSTEM RESET V1 LED S2 RST S1 RST GND TOL 0.1F 0.1F 29045 TA02 SYSTEM RESET 29045 TA03 5V, 3.3V Dual Supply Monitor with Voltage Margining for Automated On-Board Testing 5V DC/DC CONVERTER SYSTEM LOGIC 3.3V V1 V2 LTC2905 VIN SUPPLY CONTROLLER 0.1F S1 0.1F TMR 22nF THREE-STATE S2 GND TOL RST 29045 TA04 3.3V, 1.2V Dual Supply Monitor with Asymmetric Hysteresis, 5% Tolerance (Supplies Rising), 10% Tolerance (After RST Goes Low) 1.2V V2 V1 LTC2904 3.3V 10k S2 RST S1 TOL GND RST 0.1F 0.1F SYSTEM RESET 29045 TA05 29045fd 13 LTC2904/LTC2905 PACKAGE DESCRIPTION DDB Package 8-Lead Plastic DFN (3mm x 2mm) (Reference LTC DWG # 05-08-1702 Rev B) 0.61 0.05 (2 SIDES) 3.00 0.10 (2 SIDES) R = 0.115 TYP 5 R = 0.05 TYP 0.40 0.10 8 0.70 0.05 2.55 0.05 1.15 0.05 PACKAGE OUTLINE 0.25 0.05 0.50 BSC 2.20 0.05 (2 SIDES) PIN 1 BAR TOP MARK (SEE NOTE 6) 0.200 REF 2.00 0.10 (2 SIDES) 0.56 0.05 (2 SIDES) 0.75 0.05 0 - 0.05 RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS 4 0.25 0.05 1 PIN 1 R = 0.20 OR 0.25 x 45 CHAMFER (DDB8) DFN 0905 REV B 0.50 BSC 2.15 0.05 (2 SIDES) BOTTOM VIEW--EXPOSED PAD NOTE: 1. DRAWING CONFORMS TO VERSION (WECD-1) IN JEDEC PACKAGE OUTLINE M0-229 2. DRAWING NOT TO SCALE 3. ALL DIMENSIONS ARE IN MILLIMETERS 4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE 5. EXPOSED PAD SHALL BE SOLDER PLATED 6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE TOP AND BOTTOM OF PACKAGE 29045fd 14 LTC2904/LTC2905 PACKAGE DESCRIPTION TS8 Package 8-Lead Plastic TSOT-23 (Reference LTC DWG # 05-08-1637) 0.52 MAX 2.90 BSC (NOTE 4) 0.65 REF 1.22 REF 1.4 MIN 3.85 MAX 2.62 REF 2.80 BSC 1.50 - 1.75 (NOTE 4) PIN ONE ID RECOMMENDED SOLDER PAD LAYOUT PER IPC CALCULATOR 0.22 - 0.36 8 PLCS (NOTE 3) 0.65 BSC 0.80 - 0.90 0.20 BSC 0.01 - 0.10 1.00 MAX DATUM `A' 0.30 - 0.50 REF 0.09 - 0.20 (NOTE 3) 1.95 BSC TS8 TSOT-23 0802 NOTE: 1. DIMENSIONS ARE IN MILLIMETERS 2. DRAWING NOT TO SCALE 3. DIMENSIONS ARE INCLUSIVE OF PLATING 4. DIMENSIONS ARE EXCLUSIVE OF MOLD FLASH AND METAL BURR 5. MOLD FLASH SHALL NOT EXCEED 0.254mm 6. JEDEC PACKAGE REFERENCE IS MO-193 29045fd Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 15 LTC2904/LTC2905 TYPICAL APPLICATION 3.3V, 1.2V Dual Supply Monitor with LED Power Good Indicator, 7.5% Tolerance and Adjustable Timer 3.3V 1.8V V1 V2 1.2V V2 LTC2905 TMR 0.1F TOL S2 22nF TMR 0.1F 510 0.1F LED RST GND TOL 22nF GND S1 2.5V V1 LTC2905 0.1F S2 S1 RST 29045 TA06 RELATED PARTS PART NUMBER DESCRIPTION COMMENTS LTC690 5V Supply Monitor, Watchdog Timer and Battery Backup 4.65V Threshold LTC694-3.3 3.3V Supply Monitor, Watchdog Timer and Battery Backup 2.9V Threshold LTC699 5V Supply Monitor and Watchdog Timer 4.65V Threshold LTC1232 5V Supply Monitor, Watchdog Timer and Pushbutton Reset 4.37V/4.62V Threshold LTC1326/LTC1326-2.5 Micropower Precision Triple Supply Monitor for 5V/2.5V, 3.3V and ADJ 4.725V, 3.118V, 1V Threshold (0.75%) LTC1536 Precision Triple Supply Monitor for PCI Applications Meets PCI tFAIL Timing Specifications LTC1726-2.5/LTC1726-5 Micropower Triple Supply Monitor for 2.5V/5V, 3.3V and ADJ Adjustable RESET and Watchdog Timeouts LTC1727-2.5/LTC1727-5 Micropower Triple Supply Monitor with Open-Drain Reset Individual Monitor Outputs in MSOP LTC1728-1.8/LTC1728-3.3 Micropower Triple Supply Monitor with Open-Drain Reset 5-Lead SOT-23 Package LTC1728-2.5/LTC1728-5 Micropower Triple Supply Monitor with Open-Drain Reset 5-Lead SOT-23 Package LTC1985-1.8 Micropower Triple Supply Monitor with Push-Pull Reset Output 5-Lead SOT-23 Package LTC2900 Programmable Quad Supply Monitor Adjustable RESET, 10-Lead MSOP, DFN Packages LTC2901 Programmable Quad Supply Monitor Adjustable RESET and Watchdog Timer, 16-Lead SSOP Package LTC2902 Programmable Quad Supply Monitor Selectable Tolerance, RESET Disable for Margining Functions, 16-Lead SSOP Package LTC2903-1 Precision Quad Supply Monitor Ultralow Voltage RESET, 6-Lead SOT-23 Package LTC2906 Dual Supply Monitor with One Pin-Selectable Threshold and One Adjustable Input 0.5V Adjustable Threshold and Three Supply Tolerances, 8-Lead SOT-23 and DFN Packages LTC2907 Dual Supply Monitor with One Pin-Selectable Threshold and One Adjustable Input 0.5V Adjustable Threshold, Adjustable RESET Timer and Three Supply Tolerances, 8-Lead SOT-23 and DFN Packages LTC2908 Precision Six Supply Monitors Ultralow Voltage RESET, 8-Lead SOT-23 and DFN Packages 29045fd 16 Linear Technology Corporation LT 1109 REV D * PRINTED IN USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 FAX: (408) 434-0507 www.linear.com (c) LINEAR TECHNOLOGY CORPORATION 2003