5962-8765004JA(ST) - e2v Aerospace & Defense

REVISIONS

LTR DESCRIPTION DATE (YR MO DAY) APPROVED

A Add one vendor, CAGE 65786. Add device types 03 and 04. Add

margin test, programming procedure, waveform, and flowchart for

method B. Add case outline letter K.

88-10-25

M. A. Frye

B Add "Changes in accordance with NOR 5962-R103-92." 91-12-24

M. A. Frye

C Redraw with changes. Add device type 05 for vendor CAGE 65786.

Changes to margin methods A and B. Add vendor CAGE 66759 as a

source of supply for device types 01JX, 01LX, and 013X with vendor

similar part number changes. Editorial changes throughout.

93-03-23

M. A. Frye

D Made correction to paragraph 1.2.2 for case outline 3, under package

style change rectangular to square. Updated drawing to the latest

format. Redrew entire document. -sld

02-10-30

Raymond Monnin

E Made correction to paragraph 1.2.1 and added additional vendor

similar PIN numbers for device types 03 and 05 on the Standard

Microcircuit Drawing Bulletin. -sld

02-12-16

Raymond Monnin

F Boilerplate update and part of five year review. tcr 07-11-01 Robert M. Heber

THE ORIGINAL FIRST PAGE OF THIS DRAWING HAS BEEN REPLACED

REV

SHEET

REV

SHEET

REV STATUS

REV

OF SHEETS

SHEET 1 2 3 4 5 6 7 8 9 10 11

PMIC N/A

PREPARED BY

Rick Officer

STANDARD

MICROCIRCUIT

DRAWING

CHECKED BY

Charles Reusing

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43218-3990

http://www.dscc.dla.mil

THIS DRAWING IS

AVAILABLE

FOR USE BY All

DEPARTMENTS

APPROVED BY

Michael. A. Frye

AND AGENCIES OF THE

DEPARTMENT OF DEFENSE

DRAWING APPROVAL DATE

88-01-04

MICROCIRCUIT, MEMORY, DIGITAL, CMOS,

2K x 8 UV ERASABLE PROM, MONOLITHIC

SILICON

AMSC N/A

REVISION LEVEL

F SIZE

CAGE CODE

67268 5962-87650

SHEET

1 OF

DSCC FORM 2233

APR 97 5962-E035-08

STANDARD

MICROCIRCUIT DRAWING

SIZE

5962-87650

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43218-3990 REVISION LEVEL

F SHEET 2

DSCC FORM 2234

APR 97

1. SCOPE

1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in

accordance with MIL-PRF-38535, appendix A.

1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example:

5962-87650 01 J A

Drawing number Device type

(see 1.2.1) Case outline

(see 1.2.2) Lead finish

(see 1.2.3)

1.2.1 Device type(s). The device type(s) identify the circuit function as follows:

Device type Generic number Circuit function Access time

01 WS57C191-50, CY7C291-50 2K x 8 UV EPROM 50 ns

02 WS57C191-55 2K x 8 UV EPROM 55 ns

03 7C291-35, CY7C291-35, WS57C291C-35 2K x 8 UV EPROM 35 ns

04 WS57C191B-45 2K x 8 UV EPROM 45 ns

05 7C291A-25, WS57C291C-25 2K x 8 UV EPROM 25 ns

1.2.2 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows:

Outline letter Descriptive designator Terminals Package style 1/

J GDIP1-T24 or CDIP2-T24 24 Dual-in-line

K GDFP2-F24 or CDFP3-F24 24 Flat package

L GDIP3-T24 or CDIP4-T24 24 Dual-in-line

3 CQCC1-N28 28 Square leadless chip carrier

1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A.

1.3 Absolute maximum ratings.

Supply voltage range (VCC) ............................................................ +4.5 V dc to +5.5 V dc

Storage temperature range ........................................................... -65°C to +150°C

Voltages on any pin with respect to ground ................................... -0.6 V dc to +7.0 V dc

PP with respect to ground .............................................................. -0.6 V dc to +14.0 V dc

Power dissipation (PD) .................................................................... 550 mW 2/

Lead temperature (soldering, 10 seconds) .................................... +300°C

Thermal resistance, junction-to-case (θJC) ..................................... See MIL-STD-1835

Endurance ..................................................................................... 50 cycles/byte, minimum

Data retention ................................................................................ 10 years, minimum

1.4 Recommended operating conditions.

Case operating temperature range (TC) ........................................ -55°C to +125°C

1/ Lid shall be transparent to permit ultraviolet light erasure.

2/ Must withstand the added PD due to short circuit test (e.g., IOS).

STANDARD

MICROCIRCUIT DRAWING

SIZE

5962-87650

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43218-3990 REVISION LEVEL

F SHEET 3

DSCC FORM 2234

APR 97

2. APPLICABLE DOCUMENTS

2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a

part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in

the solicitation or contract.

DEPARTMENT OF DEFENSE SPECIFICATION

MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for.

DEPARTMENT OF DEFENSE STANDARDS

MIL-STD-883 - Test Method Standard Microcircuits.

MIL-STD-1835 - Interface Standard Electronic Component Case Outlines.

DEPARTMENT OF DEFENSE HANDBOOKS

MIL-HDBK-103 - List of Standard Microcircuit Drawings.

MIL-HDBK-780 - Standard Microcircuit Drawings.

(Copies of these documents are available online at http://assist.daps.dla.mil/quicksearch/ or http://assist.daps.dla.mil or from

the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)

2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text

of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a

specific exemption has been obtained.

3. REQUIREMENTS

3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for non-

JAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer

Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MIL-

PRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and qualifying

activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan

may make modifications to the requirements herein. These modifications shall not affect form, fit, or function of the device.

These modifications shall not affect the PIN as described herein. A "Q" or "QML" certification mark in accordance with MIL-

PRF-38535 is required to identify when the QML flow option is used.

3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified

in MIL-PRF-38535, appendix A and herein.

3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.2 herein.

3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1.

3.2.3 Truth table(s). See 3.2.3.1 and 3.2.3.2.

3.2.3.1 Unprogrammed or erased devices. The truth table for unprogrammed devices shall be as specified on figure 2.

3.2.3.2 Programmed devices. The requirements for supplying programmed devices are not part of this drawing.

3.2.4 Block diagram. The block diagram shall be as specified on figure 3.

STANDARD

MICROCIRCUIT DRAWING

SIZE

5962-87650

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43218-3990 REVISION LEVEL

F SHEET 4

DSCC FORM 2234

APR 97

3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are

as specified in table I and shall apply over the full case operating temperature range.

3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical

tests for each subgroup are described in table I.

3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN listed

in 1.2 herein. In addition, the manufacturer's PIN may also be marked. For packages where marking of the entire SMD PIN

number is not feasible due to space limitations, the manufacturer has the option of not marking the "5962-" on the device.

3.5.1 Certification/compliance mark. A compliance indicator “C” shall be marked on all non-JAN devices built in compliance

to MIL-PRF-38535, appendix A. The compliance indicator “C” shall be replaced with a "Q" or "QML" certification mark in

accordance with MIL-PRF-38535 to identify when the QML flow option is used.

3.6 Processing EPROMS. All testing requirements and quality assurance provisions herein shall be satisfied by the

manufacturer prior to delivery.

3.6.1 Erasure of EPROMS. When specified, devices shall be erased in accordance with the procedures and characteristics

specified in 4.4.

3.6.2 Programmability of EPROMS. When specified, devices shall be programmed to the specified pattern using the

procedures and characteristics specified in 4.5.

3.6.3 Verification of erasure or programmability of EPROMS. When specified, devices shall be verified as either

programmed to the specified pattern or erased. As a minimum, verification shall consist of performing a functional test

(subgroups 7 and 8) to verify that all bits are in proper state. Any bit that does not verify to be in the proper state shall

constitute a device failure and shall be removed from the lot.

3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an

approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DSCC-VA prior to

listing as an approved source of supply shall affirm that the manufacturer's product meets the requirements of MIL-PRF-38535,

appendix A and the requirements herein.

3.8 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided

with each lot of microcircuits delivered to this drawing.

3.9 Notification of change. Notification of change to DSCC-VA shall be required for any change that affects this drawing

3.10 Verification and review. DSCC, DSCC's agent, and the acquiring activity retain the option to review the manufacturer's

facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the

reviewer.

3.11 Data retention. A data retention stress test shall be completed as part of the vendor's reliability monitors. This test shall

be done for initial characterization and after any design or process change which may affect data retention. The methods and

procedures may be vendor specific, but shall guarantee the number of years listed in section 1.3 herein over the full military

temperature range. The vendor's procedure shall be kept under document control and shall be made available upon request of

the acquiring or preparing activity, along with test data.

3.12 Endurance. A reprogrammability test shall be completed as part of the vendor's reliability monitors. This test shall be

done for initial characterization and after any design or process change which may affect the reprogrammability of the device.

The methods and procedures may be vendor specific, but shall guarantee the number of program/erase endurance cycles listed

in section 1.3 herein over the full military temperature range. The vendor's procedure shall be kept under document control and

shall be made available upon request of the acquiring or preparing activity, along with test data.

STANDARD

MICROCIRCUIT DRAWING

SIZE

5962-87650

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43218-3990 REVISION LEVEL

F SHEET 5

DSCC FORM 2234

APR 97

TABLE I. Electrical performance characteristics.

Limits Test Symbol Conditions 1/

-55°C ≤ TC ≤+125°C

4.5 V dc ≤ VCC ≤ 5.5 V dc

unless otherwise specified

Group A

subgroups Device

types Min Max

Unit

Input low voltage VIL V

CC = 4.5 V and 5.5 V 1,2,3 All -0.5

2/ 0.8 V

Input high voltage VIH V

CC = 4.5 V and 5.5 V 1,2,3 All 2.0 VCC +0.5

2/ V

Output low voltage 3/ VOL I

OL = 16 mA, VCC = 4.5 V,

VIL = 0.8 V, VIH = 2.0 V 1,2,3 All 0.45 V

Output high voltage 3/ VOH I

OH = -4 mA, VCC = 4.5 V,

VIL = 0.8 V, VIH = 2.0 V 1,2,3 All 2.4 V

Output short circuit 2/

current IOS V

CC = 4.5 V and 5.5 V,

VOUT = GND 1,2,3 All 200 mA

Input load current 4/ ILI V

IN = 5.5 V and GND 1,2,3 All ±10 μA

Output leakage ILO V

OUT = 5.5 V and GND 1,2,3 All ±10 μA

Operating current, TTL

inputs 5/ 6/ 7/ ICC

TTL 1CS = VIL, VCC = 5.5 V,

O0 to O7 = 0 mA, CS2 = CS3 =

VIH, addresses cycling between

0 V and 3 V

1,2,3 All 120 mA

Operating current ,

CMOS inputs 2/ 7/ 8/ ICC

CMOS 1CS = VIL, VCC = 5.5 V,

O0 to O7 = 0 mA, CS2 = CS3 =

VIH

1,2,3 All 120 mA

Input capacitance CIN V

IN = 0, see 4.3.1c 4 All 10 pF

Output capacitance COUT V

OUT = 0, see 4.3.1c 4 All 12 pF

01 50

02 55

03 35

04 45

Address to output delay tACC 1CS = VIL, CS2 = CS3 = VIH,

See figures 4 and 5 9,10,11

05 25

01,03,

04 25

02 30

All chip selects to output

delay tCS Either 1CS , CS2 or CS3 9/

See figures 4 and 5 9,10,11

05 20

01,02,

03,04 25 All chip selects high to

output float 2/ tDF Either 1CS , CS2 or CS3 9/

See figures 4 and 5 9,10,11

05 20

Address to output hold

2/ tOH 1CS = VIL, CS2 = CS3 = VIH,

See figures 4 and 5 9,10,11 All 0 ns

See footnotes at top of next page.

STANDARD

MICROCIRCUIT DRAWING

SIZE

5962-87650

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43218-3990 REVISION LEVEL

F SHEET 6

DSCC FORM 2234

APR 97

TABLE I. Electrical performance characteristics -Continued.

1/ All electrical performance characteristics are 100 percent tested unless otherwise specified.

2/ May not be tested, but shall be guaranteed to the limits specified in table I.

3/ These are absolute voltages with respect to device ground pin and include all over shoots due to system and/or tester noise.

Do not attempt to test these values without suitable equipment.

4/ Output shall be loaded in accordance with figure 4.

5/ TTL inputs: VIL ≤ 0.8 V, VIH ≥ 2.0 V.

6/ The frequency equals 1/tACC (maximum).

7/ The addresses, (A0 - A10 pins), are toggling between VIL and VIH.

8/ CMOS inputs: VIL = GND ±0.3 V, VIH = VCC ±0.3 V.

9/ Worst case of output control signal lines 1CS , CS2, or CS3.

STANDARD

MICROCIRCUIT DRAWING

SIZE

5962-87650

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43218-3990 REVISION LEVEL

F SHEET 7

DSCC FORM 2234

APR 97

Device types All

Case outlines J, K, L 3

Terminal

number T erminal symbol

1 A7 NC

2 A6 A

3 A5 A

4 A4 A

5 A3 A

6 A2 A

7 A1 A

8 A0 A

9 O0 A

10 O1 NC

11 O2 O

12 GND O1

13 O3 O

14 O4 GND

15 O5 NC

16 O6 O

17 O7 O

18 CS3 O5

19 CS2 O6

20 1CS /VPP O7

21 A10 NC

22 A9 CS3

23 A8 CS2

24 VCC 1CS /VPP

25 --- A10

26 --- A9

27 --- A8

28 --- VCC

FIGURE 1. Terminal connections.

STANDARD

MICROCIRCUIT DRAWING

SIZE

5962-87650

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43218-3990 REVISION LEVEL

F SHEET 8

DSCC FORM 2234

APR 97

Mode 1CS /VPP CS2

CS3

I/O pins

Program VPP X X Data in

Read VIL VIH VIH Data out

Deselect VIH X X High-Z

Deselect X VIL X High-Z

Deselect X X VIL High-Z

NOTE: X means the input is a "don't care".

FIGURE 2. Truth table for unprogrammed devices.

FIGURE 3. Block diagram.

STANDARD

MICROCIRCUIT DRAWING

SIZE

5962-87650

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43218-3990 REVISION LEVEL

F SHEET 9

DSCC FORM 2234

APR 97

High impedance test systems only

* tDF is tested with CL = 5 pF.

FIGURE 4. Output load (suggested).

FIGURE 5. AC read timing diagram.

STANDARD

MICROCIRCUIT DRAWING

SIZE

5962-87650

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43218-3990 REVISION LEVEL

F SHEET 10

DSCC FORM 2234

APR 97

4. VERIFICATION

4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38535,

appendix A.

4.2 Screening. Screening shall be in accordance with method 5004 of MIL-STD-883, and shall be conducted on all devices

prior to quality conformance inspection. The following additional criteria shall apply:

a. Burn-in test, method 1015 of MIL-STD-883.

(1) Test condition C or D. The test circuit shall be maintained by the manufacturer under document revision level

control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify

the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method

1015 of MIL-STD-883.

(2) TA = +125°C, minimum.

b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter

tests prior to burn-in are optional at the discretion of the manufacturer.

c. A data retention stress test shall be included as part of the screening procedure. Margin methods shall be maintained

by the manufacturer under document revision level control and shall be made available to the preparing or acquiring

activity upon request.

4.3 Quality conformance inspection. Quality conformance inspection shall be in accordance with method 5005 of

MIL-STD-883 including groups A, B, C, and D inspections. The following additional criteria shall apply.

4.3.1 Group A inspection.

a. Tests shall be as specified in table II herein.

b. Subgroups 5 and 6 in table I, method 5005 of MIL-STD-883 shall be omitted.

c. Subgroup 4 (CIN and COUT measurements) shall be measured only for the initial test and after process or design

changes which may affect input capacitance. A minimum sample of five (5) devices with zero failures shall be

required.

d. All devices selected for testing shall be programmed with a checkerboard pattern or equivalent. After completion of all

testing, the devices shall be erased and verified (except devices submitted for groups C and D testing).

4.3.2 Groups C and D inspections.

a. End-point electrical parameters shall be as specified in table II herein.

b. Steady-state life test conditions, method 1005 of MIL-STD-883.

(1) T est condition C or D. The test circuit shall be maintained by the manufacturer under document revision level

control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall

specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in

method 1005 of MIL-STD-883.

(2) TA = +125°C, minimum.

(3) T est duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883.

4.4 Erasing procedure. The device is erased by exposure to high intensity shortwave ultraviolet light at a wavelength of

253.7 nm. The recommended integrated dose (i.e., UV intensity X exposure time) is 15 W-s/cm2. An example of an ultraviolet

source which can erase the device in 30 minutes is the model S52 shortwave ultraviolet lamp. The lamp should be used

without short wave filters and the EPROM should be placed about one inch from the lamp tubes. After erasure, all bits are in

the high state.

4.5 Programming procedures. The programming procedures shall be as specified by the device manufacturer and shall be

made available upon request.

STANDARD

MICROCIRCUIT DRAWING

SIZE

5962-87650

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43218-3990 REVISION LEVEL

F SHEET 11

DSCC FORM 2234

APR 97

TABLE II. Electrical test requirements. 1/ 2/ 3/ 4/ 5/

MIL-STD-883 test requirements

Subgroups

(in accordance with

MIL-STD-883, method 5005,

table I)

Interim electrical parameters

(method 5004)

- - -

Final electrical test parameters

(method 5004)

1*, 2, 3, 7*, 8A, 8B, 9

Group A test requirements

(method 5005)

1, 2, 3, 4**, 7, 8A, 8B, 9, 10, 11

Groups C and D end-point

electrical parameters

(method 5005)

2, 3, 7, 8A, 8B

1/ * PDA applies to subgroup 1 and 7.

/ ** See 4.3.1c.

/ Any or all subgroup may be combined when using a high speed tester.

/ Subgroup 7, 8A, and 8B shall consist of verifying the pattern specified.

/ For all electrical tests, the device shall be programmed to the pattern specified.

5. PACKAGING

5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38535, appendix A.

6. NOTES

6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications

(original equipment), design applications, and logistics purposes.

6.2 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a

contractor-prepared specification or drawing.

6.3 Configuration control of SMD's. All proposed changes to existing SMD's will be coordinated with the users of record for

the individual documents. This coordination will be accomplished using DD Form 1692, Engineering Change Proposal.

6.4 Record of users. Military and industrial users shall inform Defense Supply Center Columbus (DSCC) when a system

application requires configuration control and the applicable SMD. DSCC will maintain a record of users and this list will be

used for coordination and distribution of changes to the drawings. Users of drawings covering microelectronics devices (FSC

5962) should contact DSCC-VA, telephone (614) 692-0544.

6.5 Comments. Comments on this drawing should be directed to DSCC-VA, Columbus, Ohio 43218-3990, or telephone

(614) 692-0547.

6.6 Approved sources of supply. Approved sources of supply are listed in MIL-HDBK-103. The vendors listed in MIL-

HDBK-103 have agreed to this drawing and a certificate of compliance (see 3.7 herein) has been submitted to and accepted by

DSCC-VA.

STANDARD MICROCIRCUIT DRAWING BULLETIN

DATE: 07-11-01

Approved sources of supply for SMD 5962-87650 are listed below for immediate acquisition information only and shall

be added to MIL-HDBK-103 and QML-38535 during the next revision. MIL-HDBK-103 and QML-38535 will be revised

to include the addition or deletion of sources. The vendors listed below have agreed to this drawing and a certificate

of compliance has been submitted to and accepted by DSCC-VA. This information bulletin is superseded by the next

dated revision of MIL-HDBK-103 and QML-38535. DSCC maintains an online database of all current sources of

supply at http://www.dscc.dla.mil/Programs/Smcr/.

See footnotes at end of table.

Page 1 of 2

Standard

microcircuit drawing

PIN 1/

Vendor

CAGE

number

Vendor

similar

PIN 2/

5962-8765001JA 0C7V7 WS57C191C-50DMB

0C7V7 QP7C292A-50WMB

5962-8765001KA 0C7V7 WS57C291C-50FMB

0C7V7 QP7C291A-50TMB

5962-8765001LA 3/ CY7C291-50WMB

0C7V7 WS57C291C-50TMB

0C7V7 QP7C291A-50WMB

0C7V7 7C291A-50/LA

5962-87650013A 0C7V7 WS57C291C-50CMB

0C7V7 QP7C291A-50QMB

5962-87650013C 0C7V7 WS57C291C-50CMB

5962-8765002JA 0C7V7 WS57C191C-55DMB

0C7V7 QP7C292A-55WMB

5962-8765002KA 0C7V7 WS57C291C-55FMB

0C7V7 QP7C291A-55TMB

5962-8765002LA 0C7V7 WS57C291C-55TMB

0C7V7 QP7C291A-55WMB

5962-87650023A 0C7V7 WS57C291C-55CMB

0C7V7 QP7C291A-55QMB

5962-87650023C 0C7V7 WS57C291C-55CMB

5962-8765003KA 0C7V7 WS57C291C-35FMB

0C7V7 7C291-35/KA

0C7V7 QP7C291A-35TMB

5962-8765003LA 0C7V7 WS57C291C-35TMB

0C7V7 7C291A-35/LA

0C7V7 QP7C291A-35WMB

65786 CY7C291-35WMB

5962-87650033A 0C7V7 WS57C291C-35CMB

0C7V7 7C291-35/3A

0C7V7 QP7C291A-35QMB

5962-87650033C 0C7V7 WS57C291C-35CMB

5962-8765003JA 0C7V7 QP7C292A-35WMB

5962-8765004JA 0C7V7 WS57C191C-45DMB

0C7V7

QP7C292A-45WMB

5962-8765004KA 0C7V7 WS57C291C-45FMB

0C7V7 QP7C291A-45TMB

STANDARD MICROCIRCUIT DRAWING BULLETIN - CONTINUED.

DATE: 07-11-01

1/ The lead finish shown for each PIN representing a hermetic

package is the most readily available from the manufacturer

listed for that part. If the desired lead finish is not listed contact

the vendor to determine its availability.

2/ Caution. Do not use this number for item acquisition. Items

acquired to this number may not satisfy the performance requirements

of this drawing.

3/ Not available from an approved source.

Vendor CAGE Vendor name

number and address

0C7V7 QP Semiconductor

2945 Oakmead Village Court

Santa Clara, CA 95051

65786 Cypress Semiconductor Corporation

3901 North First Street

San Jose, CA 95134

2 of 2

Standard

microcircuit drawing

PIN 1/

Vendor

CAGE

number

Vendor

similar

PIN 2/

5962-8765004LA 0C7V7 WS57C291C-45TMB

0C7V7 QP7C291A-45WMB

5962-87650043A 0C7V7 WS57C291C-45CMB

0C7V7 7C291A-45/3A

0C7V7 QP7C291A-45QMB

5962-87650043C 0C7V7 WS57C291C-45CMB

5962-8765005KA 0C7V7 WS57C291C-25FMB

0C7V7 7C291A-25/KA

0C7V7 QP7C291A-25TMB

5962-8765005LA 0C7V7 WS57C291C-25TMB

0C7V7 7C291A-25/LA

0C7V7 QP7C291A-25WMB

5962-87650053A 0C7V7 WS57C291C-25CMB

0C7V7 7C291A-25/3A

0C7V7 QP7C291A-25QMB

5962-87650053C 0C7V7 WS57C291C-25CMB

5962-8765005JA 0C7V7 QP7C292A-25WMB

The information contained herein is disseminated for convenience only and the

Government assumes no liability whatsoever for any inaccuracies in the

information bulletin.