PLC High Density Analog I/O Module Features * 8-pt (0-10V DC / 4-20mA) input module * 2-pt (-10 to +10VDC / 4-20mA) output module * 16-bit Resolution * Fast Conversion Times * Configure up to 56 analog I/Os Specifications General Specifications Part Number FC4A-J8C1 Rated Power Voltage 24V DC Allowable Voltage Range 20.4 to 28.8V DC Terminal Arrangement See Analog I/O Module User's Manual -pages 2-8 to 2-11 Connector on Mother Board MC1.5/10-G-3.81BK (Phoenix Contact) Connector Insertion/ Removal Durability 100 times minimum FC4A-K2C1 www.idec.com/PLC Analog Output Specifications Part Number 40mA (5V DC) 60mA (5V DC) 0mA (24V DC) 0mA (24V DC) External Current Draw (Note) 50mA (24V DC) 85mA (24V DC) Weight 140g 110g Internal Current Draw For more information on these and other IDEC PLCs, visit: Output Range Load DA Conversion Analog Input Specifications FC4A-J8C1 Analog Input Signal Type Voltage Input Current Input Input Range 0 to 10V DC 4 to 20mA Input Impedance 1 M 100 Input Error AD Conversion Part Number FC4A-K2C1 Output Error Voltage -10 to +10V DC Current 4 to 20mA DC Load Impedance 2 k minimum (voltage), 300 maximum (current) Applicable Load Type Resistive load Settling Time 1ms / ch Total Output System Transfer Time 1ms x channels + 1 scan time Maximum Error at 25C 0.2% of full scale Temperature Coefficient 0.005% of full scale/C Repeatability after Stabilization Time 0.5% of full scale Output Voltage Drop 1% of full scale Sample Duration Time 2ms maximum Non-lineality 0.2% of full scale Sample Repetition Time 2ms maximum Output Ripple 0.1% of full scale Total Input System Transfer TimeNote 1 8ms x channels + 1 scan time Overshoot 0% Type of Input Single-ended input Total Error 1% of full scale Operating Mode Self-scan Conversion Method Successive approximation register method Maximum Error at 25C 0.2% of full scale Temperature Coefficient 0.005% of full scale / C Repeatability after Stabilization Time 0.5% of full scale Non-lineality 0.04% of full scale Maximum Error 1% of full scale Digital Resolution 50000 increments (16 bits) Output Value of LSB Voltage 0.4mV Current 0.32A -25000 to 25000 (voltage) Data Data Type in Application Program Monotonicity 0 to 50000 (current) Optional: -32768 to 32767 (selectable for each channel)Note 2 Yes Specifications con't on following page Specifications con't Analog Output Specifications Digital Resolution 50000 increments (16 bits) Input Value of LSB 0.2mV Current Loop Open 0.32A Data Type in Application Program Default: 0 to 50000 Monotonicity Optional: -32768 to 32767 (selectable for each channel)Note 2 Input Data Out of Range DetectableNote 3 Maximum Temporary Deviation during Electrical Noise TestsNote 4 3% maximum Input Filter Software Recommended Cable for Noise Immunity Twisted pair cable Crosstalk 2 LSB maximum Recommended Cable for Noise Immunity Twisted pair cable Crosstalk 2 LSB maximum Isolation Photocoupler-isolated between output and internal circuit Effect of Improper Output Connection No damage Selection of Analog Output Signal Type Using software programming Mounting Hole Layout (mm) No damage 23.5 Maximum Permanent Allowed Overload (No Damage) 11V DC Selection of Analog Input Signal Type Using software programming 6.3 22 mA DC 90.0 Notes: 1. Total input system transfer time = Sample repetition time + Internal processing time. The total input system transfer time increases in proportion to the number of of channels used. 2. The data processed in the analog I/O module can be linear-converted to a a value between -32768 and 32767. The the optional range designation, and analog I/O data minimum and maximum values can be selected using data registers allocated to analog I/O modules. 3. When an error is detected, a corresponding error code is stored to a data register allocated to analog I/O operating status. 4. The value is measured when a 500V clamp voltage is applied to the power supply and I/O lines. 4.3 2-o 113.00.2 Photocoupler-isolated between input and internal circuit Effect of Improper Input Connection Maximum Temporary Deviation during 3% maximum Electrical Noise TestsNote 4 Isolated between output and power circuit Isolated between input and power circuit Isolation Noise Resistance Not detectable 103.0 Noise Resistance Data Analog Input Specifications 3.0 Dimensions (mm) FC4A-K2C1 70.0 3.8 23.5 14.6 70.0 *8.5 mm when the clamp is pulled out. 4.5* 90.0 14.6 90.0 23.5 4.5* 3.8 FC4A-J8C1 *8.5 mm when the clamp is pulled out. IDEC Corporation * 1175 Elko Drive * Sunnyvale, CA 94089 * 800-262-IDEC (4332) * Fax: 408-745-5258 * www.idec.com (c)2007 IDEC Corporation. All Rights Reserved. 03/07