© Semiconductor Components Industries, LLC, 2015
January, 2018 − Rev. 13 1Publication Order Number:
MBRS1100T3/D
MBRS1100T3G,
SBRS81100T3G,
MBRS190T3G,
SBRS8190T3G
Schottky Power Rectifier
Surface Mount Power Package
Schottky Power Rectifiers employ the use of the Schottky Barrier
principle in a large area metal-to-silicon power diode. State-of-the-art
geometry features epitaxial construction with oxide passivation and
metal overlay contact. Ideally suited for low voltage, high frequency
rectification, or as free wheeling and polarity protection diodes, in
surface mount applications where compact size and weight are critical
to the system. These state-of-the-art devices have the following
features:
Features
•Small Compact Surface Mountable Package with J-Bend Leads
•Rectangular Package for Automated Handling
•Highly Stable Oxide Passivated Junction
•High Blocking Voltage − 100 Volts
•175°C Operating Junction Temperature
•Guardring for Stress Protection
•AEC−Q101 Qualified and PPAP Capable
•These are Pb−Free Devices
Mechanical Characteristics
•Case: Epoxy, Molded
•Weight: 95 mg (approximately)
•Finish: All External Surfaces Corrosion Resistant and Terminal
Leads are Readily Solderable
•Lead and Mounting Surface Temperature for Soldering Purposes:
260°C Max. for 10 Seconds
•Shipped in 12 mm Tape and Reel, 2,500 units per reel
•Cathode Polarity Band
SCHOTTKY BARRIER
RECTIFIER
1.0 AMPERE
90, 100 VOLTS
MARKING DIAGRAM
www.onsemi.com
See detailed ordering and shipping information on page 2 o
f
this data sheet.
ORDERING INFORMATION
(Note: Microdot may be in either location)
**The Assembly Location code (A) is front sid
e
optional. In cases where the Assembly Location
is
stamped i n the package, the front side assembly cod
e
may be blank.
SMB
CASE 403A
B1 = Device Code
x = C for MBRS1100T3
9 for MBRS190T3
A = Assembly Location**
Y = Year
WW = Work Week
G= Pb−Free Package
AYWW
B1xG
G
MBRS1100T3G, SBRS81100T3G, MBRS190T3G, SBRS8190T3G
www.onsemi.com
2
MAXIMUM RATINGS
Rating Symbol Value Unit
Peak Repetitive Reverse Voltage
Working Peak Reverse Voltage
DC Blocking Voltage
MBRS190T3
MBRS1100T3
VRRM
VRWM
VR90
100
V
Average Rectified Forward Current
TL = 163°C
TL = 148°C
IF(AV) 1.0
2.0
A
Non−Repetitive Peak Surge Current
(Surge Applied at Rated Load Conditions Halfwave, Single Phase, 60 Hz) IFSM 50 A
Operating Junction Temperature (Note 1) TJ−65 to +175 °C
Voltage Rate of Change dv/dt 10 V/ns
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality
should not be assumed, damage may occur and reliability may be af fected.
1. The heat generated must be less than the thermal conductivity from Junction−to−Ambient: dPD/dTJ < 1/RqJA.
THERMAL CHARACTERISTICS
Characteristic Symbol Value Unit
Thermal Resistance − Junction−to−Lead (TL = 25°C) RqJL 22 °C/W
ELECTRICAL CHARACTERISTICS
Characteristic Symbol Value Unit
Maximum Instantaneous Forward Voltage (Note 2) (iF = 1.0 A, TJ = 25°C) VF0.75 V
Maximum Instantaneous Reverse Current (Note 2)
(Rated dc Voltage, TJ = 25°C)
(Rated dc Voltage, TJ = 100°C)
IR0.5
5.0
mA
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product
performance may not be indicated by the Electrical Characteristics if operated under different conditions.
2. Pulse Test: Pulse Width = 300 ms, Duty Cycle ≤ 2.0%.
ORDERING INFORMATION
Device Marking Package Shipping†
MBRS1100T3G B1C SMB
(Pb−Free) 2500 / Tape & Reel
SBRS81100T3G* B1C SMB
(Pb−Free) 2500 / Tape & Reel
SBRS81100T3G−VF01* B1C SMB
(Pb−Free) 2500 / Tape & Reel
MBRS190T3G B19 SMB
(Pb−Free) 2500 / Tape & Reel
SBRS8190T3G* B19 SMB
(Pb−Free) 2500 / Tape & Reel
SBRS1100T3G B19 SMB
(Pb−Free) 2500 / Tape & Reel
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
*SBRS8 Prefix for Automotive and Other Applications Requiring Unique Site and Control Change Requirements
MBRS1100T3G, SBRS81100T3G, MBRS190T3G, SBRS8190T3G
www.onsemi.com
3
TYPICAL ELECTRICAL CHARACTERISTICS
Figure 1. Typical Forward Voltage Figure 2. Typical Reverse Current*
Figure 3. Power Dissipation Figure 4. Current Derating, Lead
20
10
5
2
1
0.5
0.2
0.1
0.05
0.02 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 1.1 1.2 1.3
vF, INSTANTANEOUS VOLTAGE (VOLTS)
100°C
25°C
i , INSTANTANEOUS FORWARD CURRENT (AMPS)
F
1k
400
200
100
40
20
10
4
2
1
0.4
0.2
0.1
0.04
0.01
0.02
0 102030405060708090100
TJ = 150°C
125°C
100°C
VR, REVERSE VOLTAGE (VOLTS)
3.2
2.8
2.4
2.0
1.6
1.2
0.8
0.4
00 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0
TJ = 100°C
SQUARE
WAVE
DC
IF(AV), AVERAGE FORWARD CURRENT (AMPS)
P , AVERAGE POWER DISSIPATION (WATTS)
F(AV)
2.0
1.5
1.0
0.5
0145 150 155 160 165 170 175 180
SQUARE
WAVE
DC
TL, LEAD TEMPERATURE (°C)
I , AVERAGE FORWARD CURRENT (AMPS)
F(AV)
TJ = 150°C
IR, REVERSE CURRENT ( A)μ
*The curves shown are typical for the highest voltage device in the voltage
grouping. Typical reverse current for lower voltage selections can be estimated
from these curves if VR is sufficient below rated VR.
25°C
Figure 5. Typical Capacitance
280
260
240
220
200
180
160
140
120
100
80
60
40
20
00.1 0.2 0.5 1 2 5 10 20 50 100
VR, REVERSE VOLTAGE (VOLTS)
C, CAPACITANCE (pF)
NOTE: TYPICAL CAPACITANCE
NOTE: AT 0 V = 270 pF
MBRS1100T3G, SBRS81100T3G, MBRS190T3G, SBRS8190T3G
www.onsemi.com
4
PACKAGE DIMENSIONS
SMB
CASE 403A−03
ISSUE J
E
bD
c
L1
L
A
A1
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION b SHALL BE MEASURED WITHIN DIMENSION L1.
2.261
0.089
2.743
0.108
2.159
0.085 ǒmm
inchesǓ
SCALE 8:1
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
SOLDERING FOOTPRINT*
DIM
AMIN NOM MAX MIN
MILLIMETERS
1.95 2.30 2.47 0.077
INCHES
A1 0.05 0.10 0.20 0.002
b1.96 2.03 2.20 0.077
c0.15 0.23 0.31 0.006
D3.30 3.56 3.95 0.130
E4.06 4.32 4.60 0.160
L0.76 1.02 1.60 0.030
0.091 0.097
0.004 0.008
0.080 0.087
0.009 0.012
0.140 0.156
0.170 0.181
0.040 0.063
NOM MAX
5.21 5.44 5.60 0.205 0.214 0.220
HE
0.51 REF 0.020 REF
D
L1
HE
POLARITY INDICATOR
OPTIONAL AS NEEDED
ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries.
ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent coverage
may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein.
ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer
is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards, regardless of
any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON Semiconductor data sheets and/or specifications can and
do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s
technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized
for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices
intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and
hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees
arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was
negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright
laws and is not for resale in any manner.
P
UBLICATION ORDERING INFORMATION
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
MBRS1100T3/D
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: orderlit@onsemi.com
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your loc
al
Sales Representative
◊
