@ 9 SPRAGUE Hermetically-Sealed Metal Case Metalized Polyester-Film Capacitors Features Moderate Cost Smail Size Extensive Standard Ratings Wire Leads or Tab Terminals Electrical Specifications Operating Temperature: 55C to +105C. Capacitance Range: 0.001pF to 12.0uF. DC Voitage Range: 100 VDC to 600 VDC. Capacitance Tolerance: +20%, +10%, +5%. Voltage Derating: At +125C. 50% of +105C rating. Dissipation Factor: 1.0% Max. Voltage Test: 200% of rated voltage for 2 minutes. Insulation Resistance: At +25C. 50,000 Megohm-Microfarads or 100,000 Megohms Min. At +85C. 3,000 Megohm-Microfarads or 6,000 Megohms Min. At +105C. 250 Megohm-Microfarads or 500 Megohms Min. At +125C. 10 Megohm-Microfarads or 100 Megohms Min. Environmental Characteristics (See Test Procedures page 190.) Vibration Test (Condition B): No mechanical damage, short, open or intermittent circuits. METAL-CASE METALIZED FILM CAPACITORS Type 218P 21424 Moisture Resistance: MIL-STD-202, Method 106E, 10 cycles No visible damage. Max. A Cap. +10% Min. |.R. = 50% of initial limit Max. D.F. = 1.1% DC Life Test: 125% of rated voltage for 250 hours at +105C. No open or short circuits. No visible damage. Max. A Cap. +10% Min. I.R. = 50% of initial limit Max. D.F. = 1.25% Thermal Shock and immersion Cycling: No visible damage. Max. A Cap. +10% Min. |.R. = 50% of initial limit Max. D.F. = 1.1% Physical Characteristics Lead Pull: 5 Ibs. (2.3KG) for one minute. No physical damage. Lead Bend: After three complete consecutive bends. No damage. Marking: Sprague trademark, type or catalog number, capacitance, and voltage. 71Gs SPRAGUE METAL-CASE METALIZED FILM CAPACITORS TYPE 218P CATALOG NUMBERING SYSTEM 218P = 183 X9 100 S~s2 tL STYLE NUMBER. SEE PAGES 68 THROUGH 70 FOR STYLE VARIATIONS AND CORRESPONDING DIMENSIONS. TERMINAL. S = WIRE LEADS, T = SOLDERING TAB* *Soldering tabs are available only on case diameters equal to or greater than 0.400 inches. Soldering tabs are not available on Styles 01 and 03. ' DC VOLTAGE RATING. EXPRESSED IN VOLTS. CAPACITANCE TOLERANCE. XO = + 20% X9 = +10% X5 = +5% '\___ CAPACITANCE. EXPRESSED IN PICOFARADS. THE FIRST TWO DIGITS ARE SIGNIFICANT FIGURES; THE THIRD |S THE NUMBER OF ZEROS FOLLOWING. VALUES MUST CONFORM TO THE DECADE RATING FOR THE TOLERANCE SPECIFIED. iH SPRAGUE TYPE NUMBER. IDENTIFIES THE BASIC CAPACITOR. Leads are bare solid tinned wire. Lead wire sizes are: Case Dia. Lead AWG 175 and .195 No. 24 .235 and .312 No. 22 .400 and over No. 20 729 SPRAGUE METAL-CASE METALIZED FILM CAPACITORS TYPE 218P Catalog Number* Inches Millimeters pF + 10% Tol. D L* D L* 100 VOLTS D-C 0.018 218P183X9100S02 0.175 0.750 4.44 19.02 0.022 218P223X9100S02 0.175 0.750 4.44 19.02 0.027 218P273X9100S02 0.175 0.750 4.44 19.02 0.033 218P333X9100S02 0.175 0.750 4.44 19.02 0.039 218P393X9100S02 0.195 0.750 4.95 19.02 0.047 218P473X9100S02 0.195 0.750 4.95 19.02 0.056 218P563X9100S02 0.235 0.750 5.97 19.02 0.068 218P683X9100S02 0.235 0.750 5.97 19.02 0.082 218P823X9100S02 0.235 0.750 5.97 19.02 0.10 218P104X9100S02 0.235 0.750 5.97 19.02 0.18 218P184X9100S02 0.312 0.875 7.92 22.19 0.22 218P224X9100S02 0.312 0.875 7.92 22.19 0.27 218P274X9100S02 0.312 0.875 7.92 22.19 0.33 218P334X9100S02 0.312 0.875 7.92 22.19 0.39 218P394X9100S02 0.312 1.125 7.92 28.54 0.47 218P474X9100S02 0.312 1.125 7.92 28.54 0.56 218P564X9100S02 0.400 1.125 10.16 28.54 0.68 218P684X9100S02 0.400 1.125 10.16 28.54 0.82 218P824X9100S02 0.400 1.125 10.16 28.54 1.0 218P105X9100S02 0.400 1.125 10.16 28.54 1.5 218P155X9100S02 0.500 1.125 12.70 28.54 2.2 218P225X9100S02 0.562 1.125 14.27 28.54 2.7 218P275X9100S02 0.562 1.375 14.27 34.89 3.3 218P335X9100S02 0.562 1.375 14.27 34.89 3.9 218P395X9100S02 0.562 1.625 14.27 41.24 40 218P405X39100S02 0.562 1.625 14.27 41.24 4.7 218P475X9100S02 0.562 1.875 14.27 47.59 5.0 218P505X9100S02 0.562 1.875 14.27 47.59 5.6 218P565X9100S02 0.670 1.625 17.02 41.24 6.0 218P605X9100S02 0.670 1.625 17.02 41.24 6.8 218P685X9100S02 0.670 4.875 17.02 47.59 7.0 218P705X9100S02 0.670 1.875 17.02 47.59 10.0 218P106X9100S02 0.750 1.875 19.05 47.59 12.0 218P126X9100S02 0.750 2.375 19.05 60.29 150 VOLTS D-C 0.027 218P273X9150S02 0.195 0.750 4,95 19.02 0.033 218P333X9150S02 0.195 0.750 4.95 19.02 0.039 218P393X9150S02 0.235 0.750 5.97 19.02 0.047 218P473X9150S02 0.235 0.750 5.97 19.02 0.056 218P563X9150S02 0.235 0.750 5.97 19.02 0.068 218P683X9150S02 0.235 0.750 5.97 19.02 0.082 218P823X9150S02 0.312 0.875 7.92 22.19 0.10 218P104X9150S02 0.312 0.875 7.92 22.19 0.18 218P184X9150S02 0.312 0.875 7.92 22.19 0.22 218P224X9150S02 0.312 0.875 7.92 22.19 0.27 218P274X9150S02 0.312 1.125 7.92 28.54 0.33 218P334X9150S02 0.312 1.125 7.92 28.54 0.39 218P394X9150S02 0.400 1.125 10.16 28.54 0.47 218P474X9150S02 0.400 1.125 10.16 28.54 0.56 218P564X9150S02 0.400 1.125 10.16 28.54 The catalog numbers and dimensions shown are for style 02 with capacitance tolerance of + 10%. To specify another style, change the last two digits of catalog number and the dimensions to correspond to specific styles shown on pages 68 thru 70. To specify another capacitance tolerance change X9 to XO for + 20%, or X5 for +5%. 73SPROGUE METAL-CASE METALIZED FILM CAPACITORS TYPE 218P STANDARD RATINGS Catalog Number* __Inches ___Millimeters uF + 10% Toi. D L* D L* 150 VOLTS D-C (Cont.) 0.68 218P684X9150S02 0.400 1.125 10.16 28.54 0.82 218P824X9150S02 0.500 1.125 12.70 28.54 1.0 218P105X9150S02 0.500 1.125 12.70 28.54 1.5 218P155X9150S02 0.562 1.125 14.27 28.54 2.0 218P205X9150S02 0.562 1.375 14.27 34.89 2.2 218P225X9150S02 0.562 1.375 14.27 34.89 2.5 218P255X9150S02 0.562 1.625 14.27 41.24 2.7 218P275X9150S02 0.562 1.625 14.27 41.24 3.0 218P305X9150S02 0.670 1.375 17.02 34.89 3.3 218P335X9150S02 0.670 1.625 17.02 41.24 4.0 218P405X9150S02 0.670 1.625 17.02 41.24 47 218P475X9150S02 0.670 1.875 17.02 47.59 5.0 218P505X9150S02 0.670 1.875 17.02 47.59 5.6 218P565X9150S02 0.670 2.125 17.02 53.94 6.0 218P605X9150S02 0.750 1.875 19.05 47.59 6.8 218P685X9150S02 0.750 2.125 19.05 53.94 8.0 218P805X9150S02 0.750 2.375 19.05 60.29 10.0 218P106X9150S02 0.750 2.625 19.05 66.64 12.0 218P126X9150S02 1.000 1.875 25.40 47.59 200 VOLTS D-C 0.001 218P102X9200S02 0.175 0.750 4.44 19.02 0.0012 218P122X9200S02 0.175 0.750 4.44 19.02 0.0015 218P152X9200S02 0.175 0.750 4.44 19.02 0.0018 218P182X9200S02 0.175 0.750 4.44 19.02 0.0022 218P222X9200S02 0.175 0.750 4.44 19.02 0.0027 218P272X9200S02 0.175 0.750 4.44 19.02 0.0033 218P332X9200S02 0.175 0.750 4.44 19.02 0.0039 218P392X9200S02 0.175 0.750 4.44 19.02 0.0047 218P472X9200S02 0.175 0.750 4.44 19.02 0.0056 218P562X9200S02 0.175 0.750 4.44 19.02 0.0068 218P682X9200S02 0.175 0.750 4.44 19.02 0.0082 218P822X9200S02 0.175 0.750 4.44 19.02 0.01 218P103X9200S02 0.175 0.750 4.44 19.02 0.012 218P123X9200S02 0.175 0.750 4.44 19.02 0.015 218P153X9200S02 0.175 0.750 4.44 19.02 0.018 218P183X9200S02 0.195 0.750 4.95 19.02 0.022 218P223X9200S02 0.195 0.750 4.95 19.02 0.027 218P273X9200S02 0.235 0.750 5.97 19.02 0.033 218P333X9200S02 0.235 0.750 5.97 19.02 0.039 218P393X9200S02 0.235 0.750 5.97 19.02 0.047 218P473X9200S02 0.235 0.750 5.97 19.02 0.056 218P563X9200S02 0.312 0.875 7.92 22.19 0.068 218P683X9200S02 0.312 0.875 7.92 22.19 0.082 218P823X9200S02 0.312 0.875 7.92 22.19 0.10 218P104X9200S02 0.312 0.875 7.92 22.19 *The catalog numbers and dimensions shown are for style 02 with capacitance tolerance of + 10%. To specify another style, change the last two digits of catalog number and the dimensions to correspond to specific styles shown on pages 68 thru 70. To specify another capacitance tolerance change X9 to XO for + 20%, or X5 for + 5%. 74& i SPROGUE METAL-CASE METALIZED FILM CAPACITORS TYPE 218P STANDARD RATINGS Catalog Number* Inches Millimeters pF + 10% Tol. D L* D L* 200 VOLTS D-C (Cont.) 0.12 218P124X9200802 0.312 0.875 7.92 22.19 0.15 218P154X9200S02 0.312 0.875 7.92 22.19 0.18 218P184X9200S02 0.400 0.875 10.16 22.19 0.22 218P224X9200S02 0.400 0.875 10.16 22.19 0.27 218P274X9200S02 0.400 1.125 10.16 28.54 0.33 218P334X9200S02 0.400 1.125 10.16 28.54 0.39 218P394X9200S02 0.400 1.375 10.16 34.89 0.47 218P474X9200S02 0.400 1.375 10.16 34.89 0.56 218P564X9200S02 0.500 1.125 12.70 28.54 0.68 218P684X9200S02 0.500 1.125 12.70 28.54 0.82 218P824X9200S02 0.562 1.375 14.27 34.89 1.0 218P105X9200S02 0.562 1.375 14.27 34,89 1.5 218P155X9200S02 0.562 1.625 14.27 41.24 2.0 218P205X9200S02 0.562 1.875 14.27 47.59 2.5 218P255X9200S02 0.670 1.625 17.02 41.24 3.0 218P305X9200S02 0.670 1.875 17.02 47.59 4.0 218P405X9200S02 0.750 1.875 19.05 47.59 5.0 218P505X9200S02 0.750 2.375 19.05 60.29 6.0 218P605X9200502 0.750 2.625 19.05 66.64 7.0 218P705X9200S02 1.000 1.875 25.40 47.59 10.0 218P106X9200S02 1.000 2.375 25.40 60.29 12.0 218P126X9200502 1.000 2.625 25.40 66.64 400 VOLTS D-C 0.0039 218P392X9400S02 0.235 0.750 5.97 19.02 0.0047 218P472X9400S02 0.235 0.750 5.97 19.02 0.0056 218P562X9400S02 0.235 0.750 5.97 19.02 0.0068 218P682X9400S02 0.235 0.750 5.97 19.02 0.0082 218P822X9400S02 0.235 0.750 5.97 19.02 0.010 218P103X9400S02 0.235 0.750 5.97 19.02 0.012 218P123X9400S02 0.312 0.875 7.92 22.19 0.015 218P153X9400S02 0.312 0.875 7.92 22.19 0.018 218P183X9400S02 0.312 0.875 7.92 22.19 0.022 218P223X9400802 0.312 0.875 7.92 22.19 0.027 218P273X9400S02 0.312 0.875 7.92 22.19 0.033 218P333X9400S02 0.312 0.875 7.92 22.19 0.039 218P393X9400S02 0.400 0.875 10.16 22.19 0.047 218P473X9400S02 0.400 0.875 10.16 22.19 0.056 218P563X9400S02 0.400 1.125 10.16 28.54 0.068 218P683X9400S02 0.400 1.125 10.16 28.54 0.082 218P823X9400802 0.400 1.125 10.16 28.54 0.1 218P104X9400S02 0.400 1.125 10.16 28.54 0.12 218P124X9400S02 0.500 1.125 12.70 28.54 0.15 218P154X9400S02 0.500 1.125 12.70 28.54 0.18 218P184X9400S02 0.562 1.125 14.27 28.54 0.22 218P224X9400S02 0.562 1.125 14.27 28.54 0.27 218P274X9400S02 0.562 1.625 14.27 41,24 0.33 218P334X9400S02 0.562 1,625 14.27 41.24 0.39 218P394X9400S02 0.562 1.875 14.27 47.59 0.47 218P474X9400S02 0.562 1.875 14.27 47.59 0.56 218P564X9400S02 0.670 1.875 17.02 47.59 0.68 218P684X9400S02 0.670 1.875 17.02 47.59 0.82 218P824X9400S02 0.750 2.125 19.05 53.94 1.0 218P105X9400S02 0.750 2.125 19.05 53.94 1.5 218P155X9400S02 0.750 2.625 19.05 66.64 2.0 218P205X9400S02 1.000 2.125 29.40 53.94 2.5 218P255X9400S02 1.000 2.625 25.40 66.64 *The catalog numbers and dimensions shown are for style 02 with capacitance tolerance of + 10%. To specify another style, change the last two digits of catalog number and the dimensions to correspond to specific styles shown on pages 68 thru 70. To specify another capacitance tolerance change X9 to XO for +20%, or X5 for +5%. 75