1
dc2349af
DEMO MANUAL DC2349A
DESCRIPTION
LTC5586
6GHz High Linearity I/Q Demodulator
with Wideband IF Amplifier
Demonstration circuit 2349A showcases the LT C
®
5586
wideband high linearity IQ demodulator with IF amplifier.
The Linear Technology USB serial controller, DC590B, isre-
quired to control and configure LTC5586 for its evaluation.
Demo circuit 2349A’s two switchable single-ended RF
inputs are optimized for 700MHz to 6GHz. Its single-
ended LO input is programmable for 300MHz to 6GHz
operation via SPI bus. The demo circuit includes discrete
L-C inter-stage lowpass filters between the demodula-
tor outputs and the IF amplifier inputs, which limits the L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks and
QuikEval is a trademark of Linear Technology Corporation. All other trademarks are the property
of their respective owners.
BOARD PHOTO
DC-coupled differential I and Q outputs to about 500MHz
(–1dB bandwidth).
By writing to specific registers through SPI bus, LTC5586s
RF input step attenuator, IF amplifier gain, LO input fre-
quency, output DC offset, image rejection, and linearity
can be adjusted or optimized.
Design files for this circuit board are available at
http://www.linear.com/demo/DC2349A
2
dc2349af
DEMO MANUAL DC2349A
QUICK START PROCEDURE
NOTE 1. Evaluation of demonstration circuit 2349A requires
the Linear Technology USB serial controller, DC590B, and
the Linear Technology QuikEval™ software. Please refer
to DC590B demo manual for their setup and installation.
NOTE 2. An internet connection is required for the automatic
download and installation of the LTC5586 software GUI.
If an internet connection is not available, contact Linear
Technology for installation files
NOTE 3. Refer to Figure 1 for proper equipment setup.
NOTE 4. Make all connections without RF and DC applied.
NOTE 5. Care should be taken to never exceed absolute
maximum input ratings.
1. If not already done, install the QuikEval software
and connect the DC590B USB serial controller to an
internet-connected computer’s USB port.
2. Set the DC590B’s isolated supply voltage to 3.3V by
moving its VCCIO jumper (JP6) to 3.3V position.
3. Verify that the DC2349A’s jumpers are set to:
JP1 = INT (on-board 3.3V digital supply)
JP2 = RFA (RFA input selected)
4. While the RF sources and the DC power supplies are
switched off, connect all test equipment as shown in
Figure1.
5. When the DC2349A demo board is connected to the
DC590B USB serial controller, the QuikEval software
will automatically download and install the proper
software GUI.
6. While monitoring the voltage on VSENSE, increase
the VSUPPLY DC power supply voltage until VSENSE
reaches 5V (VSUPPLY voltage should be approxi-
mately5.5V). Verify the current consumption is close
to the figure listed in the data sheet.
7. Increase the IF amplifier common-mode output volt-
age, VCM, to 0.9V.
8. In the LTC5586 QuikEval computer GUI, verify that
“Connected” is displayed, then press the “Soft Reset
button. See Figure 2.
9. Set the desired LO frequency and LO power, and turn
on the LO signal source.
10. Use the LTC5586 QuikEval GUI to configure the
LTC5586 to the same LO frequency.
11. Set the desired RF frequency and RF power, and turn
on the RF source.
12. Perform measurements.
13. The LTC5586 QuikEval GUI can be used to control and
configure various functions of the LTC5586. Press the
button Show Regs” will make the LTC5586’s internal
register visible and accessible on screen. See Figure3.
3
dc2349af
DEMO MANUAL DC2349A
Figure 2. Proper Measurement Equipment Setup
QUICK START PROCEDURE
4
dc2349af
DEMO MANUAL DC2349A
QUICK START PROCEDURE
Figure 2. LTC5586 QuikEval GUI
5
dc2349af
DEMO MANUAL DC2349A
QUICK START PROCEDURE
Figure 3. LTC5586 QuikEval GUI Showing Internal Resisters
6
dc2349af
DEMO MANUAL DC2349A
PCB LAYOUT
7
dc2349af
DEMO MANUAL DC2349A
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representa-
tion that the interconnection of its circuits as described herein will not infringe on existing patent rights.
PCB LAYOUT
8
dc2349af
DEMO MANUAL DC2349A
Linear Technology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408) 432-1900 FAX: (408) 434-0507 www.linear.com
© LINEAR TECHNOLOGY CORPORATION 2016
LT 0616 • PRINTED IN USA
DEMONSTRATION BOARD IMPORTANT NOTICE
Linear Technology Corporation (LTC) provides the enclosed product(s) under the following AS IS conditions:
This demonstration board (DEMO BOARD) kit being sold or provided by Linear Technology is intended for use for ENGINEERING DEVELOPMENT
OR EVALUATION PURPOSES ONLY and is not provided by LTC for commercial use. As such, the DEMO BOARD herein may not be complete
in terms of required design-, marketing-, and/or manufacturing-related protective considerations, including but not limited to product safety
measures typically found in finished commercial goods. As a prototype, this product does not fall within the scope of the European Union
directive on electromagnetic compatibility and therefore may or may not meet the technical requirements of the directive, or other regulations.
If this evaluation kit does not meet the specifications recited in the DEMO BOARD manual the kit may be returned within 30 days from the date
of delivery for a full refund. THE FOREGOING WARRANTY IS THE EXCLUSIVE WARRANTY MADE BY THE SELLER TO BUYER AND IS IN LIEU
OF ALL OTHER WARRANTIES, EXPRESSED, IMPLIED, OR STATUTORY, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS
FOR ANY PARTICULAR PURPOSE. EXCEPT TO THE EXTENT OF THIS INDEMNITY, NEITHER PARTY SHALL BE LIABLE TO THE OTHER FOR
ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.
The user assumes all responsibility and liability for proper and safe handling of the goods. Further, the user releases LTC from all claims
arising from the handling or use of the goods. Due to the open construction of the product, it is the user’s responsibility to take any and all
appropriate precautions with regard to electrostatic discharge. Also be aware that the products herein may not be regulatory compliant or
agency certified (FCC, UL, CE, etc.).
No License is granted under any patent right or other intellectual property whatsoever. LTC assumes no liability for applications assistance,
customer product design, software performance, or infringement of patents or any other intellectual property rights of any kind.
LTC currently services a variety of customers for products around the world, and therefore this transaction is not exclusive.
Please read the DEMO BOARD manual prior to handling the product. Persons handling this product must have electronics training and
observe good laboratory practice standards. Common sense is encouraged.
This notice contains important safety information about temperatures and voltages. For further safety concerns, please contact a LTC application
engineer.
Mailing Address:
Linear Technology
1630 McCarthy Blvd.
Milpitas, CA 95035
Copyright © 2004, Linear Technology Corporation