4. SPECIFICATIONS FOR EACH SERIES Conductive polymer type SVQP Series Guaranteed at 125C Marking : Polarity( ), Rated voltage (Purple) QP, Rated capacitance, Lot.No. Specifications Conditions Items Category temperature range Tolerance on rated capacitance Tangent of loss angle Leakage current 1 ESR Characteristics of impedance ratio at high temp. and low temp. Characteristics -55C to +125C M : 20% 120Hz Less than or equal to the value of Table6 120Hz Less than or equal to the value of Table6 After 2 minutes Less than or equal to the value of Table6 Z / Z 20C 0.75 to 1.25 -55C Based the value at 0.75 to 1.25 Z / Z 20C +125C 100KHz+20C Within 20% C/C 2 times or less than an initial standard tan 125C, 1,000h, Rated Endurance 2 times or less than an initial standard ESR voltage applied Leakage current Below an initial standard Within 20% C/C 60C, 90 to 95%RH, 1.5 times or less than an initial standard tan Damp heat (Steady state) 1,000h, 1.5 times or less than an initial standard ESR No-applied voltage Leakage current Below an initial standard (after voltage processing) C/C Within 10% Resistance to tan 1.3 times or less than an initial standard 2 (VPS) (230C X 75s) soldering heat ESR 1.3 times or less than an initial standard Leakage current Below an initial standard (after voltage processing) 1 In case of some problems for measured values, measure after applying rated voltage for 120 minutes at 125C . 2 Refer to Page 56 for reflow soldering conditions. Dimensions (unit : mm) 0.2max. L Size List P C H W D Specificationsfor eachseries This series has advanced characteristics in resistance to heat compared with the SVP series. The SVQP series is best suited for devices that require enhanced reliability. This product can support lead free-reflow.(2). R Size Code D0.5 C6 E7 6.3 8.0 RV : Rated voltage (SV) : Surge (room temperature) 4 6.3 10 16 20 5.2 8.2 11.5 18.4 23 C6 RV SV F 22 39 C6 47 E7 56 C6 82 C6 100 C6 E7 E7 120 150 C6 E7 220 E7 E7 E7 For the minimum packing quantity, please refer to page 55. 28 L +0.1 W0.2 -0.4 5.9 6.9 6.6 8.3 H0.2 C0.2 R P0.2 6.6 8.3 7.3 9.0 0.6 to 0.8 0.6 to 0.8 2.1 3.2 4. SPECIFICATIONS FOR EACH SERIES Table6 SVQP Series Characteristics List Size Code Rated Voltage (V) Part Number 1 Rated ESR Capacitance 100kHz to 300kHz (F) (m) (max.) Rated ripple current Allowable ripple current 100kHz (mArms) 3 105Tx125 Tx105 Tangent of loss angle (max.) Leakage current (A) (max.)2 20 22 60 459 1450 0.10 220 16SVQP39M 16 39 50 512 1620 0.10 312 10SVQP56M 10 56 45 538 1700 0.12 280 Specificationsfor eachseries 20SVQP22M C6 E7 1 2 3 6SVQP82M 6.3 82 45 538 1700 0.12 258 6SVQP100M 6.3 100 40 572 1810 0.12 315 4SVQP150M 4 150 40 572 1810 0.12 300 20SVQP47M 20 47 45 598 1890 0.12 470 16SVQP82M 16 82 40 670 2120 0.12 656 10SVQP120M 10 120 35 810 2560 0.12 600 10SVQP150M 10 150 35 810 2560 0.12 750 6SVQP150M 6.3 150 35 810 2560 0.12 472 6SVQP220M 6.3 220 35 810 2560 0.12 693 4SVQP220M 4 220 35 810 2560 0.12 440 Capacitance tolerance : M 20% After 2 minutes Tx : Ambient temperature (unit : mm) Size Code C6 E7 a 2.1 2.8 b 9.1 11.1 c 1.6 1.9 c Recommended land pattern dimension of PWB a b Frequency coefficient for ripple current Frequency Coefficient 120Hz f 1kHz 0.05 1kHz f 10kHz 0.3 10kHz f 100kHz 0.7 100kHz f 500kHz 1 29