www.ti.com
FEATURES
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
GND
VCC
VCC
GND
ATX/RX
A1A
A2A
A3A
A4A
BTX/RX
B1A
B2A
B3A
B4A
GND
VCC
VCC
GND
C1A
C2A
C3A
C4A
CTX/RX
D1A
D2A
D3A
D4A
DTX/RX
GND
VCC
VCC
GND
A1Y
A1Z
A2Y
A2Z
A3Y
A3Z
A4Y
A4Z
B1Y
B1Z
B2Y
B2Z
B3Y
B3Z
B4Y
B4Z
C1Y
C1Z
C2Y
C2Z
C3Y
C3Z
C4Y
C4Z
D1Y
D1Z
D2Y
D2Z
D3Y
D3Z
D4Y
D4Z
SN65LVDM1676DGG ( Marked as LVDM1676)
SN65LVDM1677DGG (Marked as LVDM1677)
(TOP VIEW)
DESCRIPTION
SN65LVDM1676 , SN65LVDM1677
SLLS430B NOVEMBER 2000 REVISED MAY 2004
HIGH-SPEED DIFFERENTIAL LINE TRANSCEIVERS
Sixteen Low-Voltage Differential TransceiversDesigned for Signaling Rates
(1)
Up to 630Mbps
Simplex (Point-to-Point) and Half-Duplex(Multipoint) InterfaceTypical Differential Output Voltage of 340 mVInto a 50- LoadIntegrated 110- Line Termination on'LVDM1677 ProductPropagation Delay Time: Driver: 2.5 ns Typ Receiver: 3 ns TypRecommended Maximum Transfer Rate: Driver: 650 M-Transfers/s Receiver: 350 M-Transfers/sDriver is High Impedance When Disabled orWith V
CC
< 1.5 V for Power Up/DownGlitch-Free Performance and Hot-PluggingEvents
Bus-Terminal ESD Protection Exceeds 12 kVLow-Voltage TTL (LVTTL) Logic Input LevelsAre 5-V TolerantPackaged in Thin Shrink Small-OutlinePackage With 20 mil Terminal Pitch(1)
Signaling rate, 1/t, where t is the minimumunit interval and is expressed in the unitsbits/s (bits per second).
The SN65LVDM1676 and SN65LVDM1677 (integrated termination) are sixteen differential line drivers andreceivers configured as trans-ceivers that use low-voltage differential signaling (LVDS) to achieve signaling ratesin excess of 600 Mbps. These products are similar to TIA/EIA-644 standard compliant devices (SN65LVDS)counterparts except that the output current of the drivers are doubled. This modification provides a minimumdifferential output voltage magnitude of 247 mV into a 50- load and allows double-terminated lines andhalf-duplex operation. The receivers detect a voltage difference of 100 mV with up to 1 V of ground potentialdifference between a transmitter and receiver.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of TexasInstruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Copyright © 2000–2004, Texas Instruments IncorporatedProducts conform to specifications per the terms of the TexasInstruments standard warranty. Production processing does notnecessarily include testing of all parameters.
www.ti.com
DESCRIPTION (CONTINUED)
Z
Y
A
TX/RX
LVD Transceiver
SN65LVDM1676 , SN65LVDM1677
SLLS430B NOVEMBER 2000 REVISED MAY 2004
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foamduring storage or handling to prevent electrostatic damage to the MOS gates.
The intended application of this device and signaling technique is for point-to-point baseband data transmissionover controlled impedance media of approximately 100 . The transmission media may be printed-circuit boardtraces, backplanes, or cables. The large number of transceivers integrated into the same substrate along with thelow pulse skew of balanced signaling, allows extremely precise timing alignment of clock and data forsynchronous parallel data transfers. (Note: The ultimate rate and distance of data transfer is dependent upon theattenuation characteristics of the media, the noise coupling to the environment, and other system characteristics.)
The SN65LVDM1676 and SN65LVDM1677 are characterized for operation from -40°C to 85°C.
FUNCTION TABLE
(1)
INPUTS OUTPUTS
(Y - Z) TX/ RX A Y Z AV
ID
100 mV L NA Z Z H-100 mV < V
ID
< 100 mV L NA Z Z ?V
ID
-100 mV L NA Z Z LOpen circuit L NA Z Z HNA H L L H ZNA H H H L Z
(1) H = high level, L= low level, Z= high impedance, ? = indeterminate
2
Submit Documentation Feedback
www.ti.com
A1Z
A1Y
A1A
A2Z
A2Y
A2A
A3Z
A3Y
A3A
A4Z
A4Y
A4A
ATX/RX
B1Z
B1Y
B1A
B2Z
B2Y
B2A
B3Z
B3Y
B3A
B4Z
B4Y
B4A
BTX/RX
C1Z
C1Y
C1A
C2Z
C2Y
C2A
C3Z
C3Y
C3A
C4Z
C4Y
C4A
CTX/RX
D1Z
D1Y
D1A
D2Z
D2Y
D2A
D3Z
D3Y
D3A
D4Z
D4Y
D4A
DTX/RX
SN65LVDM1676 , SN65LVDM1677
SLLS430B NOVEMBER 2000 REVISED MAY 2004
LOGIC DIAGRAM (POSITIVE LOGIC)
3Submit Documentation Feedback
www.ti.com
EQUIVALENT INPUT AND OUTPUT SCHEMATIC DIAGRAMS
7 V
300 k
50
VCC
A, TX/RX Input
VCC
5
7 V
Y or Z
Output
10 k
300 k300 k
VCC
7 V 7 V
Y Input Z Input
VCC
5
7 V
A Output
110
’LVDM1677 Product Only
SN65LVDM1676 , SN65LVDM1677
SLLS430B NOVEMBER 2000 REVISED MAY 2004
4
Submit Documentation Feedback
www.ti.com
ABSOLUTE MAXIMUM RATINGS
DISSIPATION RATING TABLE
RECOMMENDED OPERATING CONDITIONS
2.4 VID
2
VID
2
ELECTRICAL CHARACTERISTICS
SN65LVDM1676 , SN65LVDM1677
SLLS430B NOVEMBER 2000 REVISED MAY 2004
over operating free-air temperature range (unless otherwise noted)
(1)
UNIT
V
CC
, see
(2)
Supply voltage range -0.5 V to 4 VInput voltage range A, TX/ RX -0.5 V to 6 VY or Z -0.5 V to 4 VV
ID
, (SN65LVDM1677 Differential input voltage magnitude 1 Vonly)
I
O
Receiver output current ±20mAElectrostatic discharge Y, Z, and GND, see
(3)
Class 3, A:8 kV, B:600 VContinuous power dissipation Class 3, A:7 kV, B:500 VStorage temperature range -65°C to 150°CLead temperature 1,6 mm (1/16 inch) from case for 10 260°Cseconds
(1) Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratingsonly, and functional operation of the device at these or any other conditions beyond those indicated under recommended operatingconditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.(2) All voltage values, except differential I/O bus voltages, are with respect to network ground terminal.(3) Tested in accordance with MIL-STD-883C Method 3015.7.
T
A
25°C OPERATING FACTOR
(1)
T
A
= 85°CPACKAGE
POWER RATING ABOVE T
A
= 25°C POWER RATING
DGG 2094 mW 16.7 mW/°C 1089 mW
(1) All typical values are at 25°C and with a 3.3-V supply.
MIN NOM MAX UNIT
V
CC
Supply voltage 3 3.3 3.6V
IH
High-level input voltage 2V
IL
Low-level input voltage 0.8
V|V
ID
| Magnitude of differential input voltage 0.1 0.6
V
IC
Common-mode input voltage
V
CC
-0.8 VI
OL
Receiver low-level output current 8
mAI
OH
Receiver high-level output current -8T
A
Operating free-air temperature -40 85 °C
over recommended operating free-air temperature range (unless otherwise noted)
PARAMETER TEST CONDITIONS MIN TYP
(1)
MAX UNIT
DEVICE
Driver enabled, receiver disabled, R
L
50 140 175I
CC
Supply current mADriver disabled, receiver enabled, no load 45 60
(1) All typical values are at 25°C and with a 3.3-V supply.
5Submit Documentation Feedback
www.ti.com
ELECTRICAL CHARACTERISTICS
ELECTRICAL CHARACTERISTICS
SN65LVDM1676 , SN65LVDM1677
SLLS430B NOVEMBER 2000 REVISED MAY 2004
over recommended operating free-air temperature range (unless otherwise noted)
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
DRIVER
JV
OD
J Differential output voltage magnitude 247 340 454R
L
= 50 , See Figure 2 and Figure 1 mVChange in differential output voltage magnitudeJV
OD
J -50 50between logic statesV
OC(SS)
Steady-state common-mode output voltage 1.125 1.375 VChange in steady-state common-mode outputV
OC(SS)
See Figure 3 -50 50 mVvoltage between logic statesV
OC(PP)
Peak-to-peak common-mode output voltage 50 150 mVI
IH
High-level input current V
IH
= 2 V 3 20 µAI
IL
Low-level input current V
IL
= 0.8 V 2 10 µAV
OY
or V
OZ
= 0 V 10 mAI
OS
Short-circuit output current
V
OD
= 0 V 10 mAI
O(OFF)
Power-off output current V
CC
= 1.5 V V
O
= 2.4 V ±10 µAC
IN
Input capacitance V
I
= 0.4 sin (4E6pt) + 0.5 V 5 pF
over recommended operating free-air temperature range (unless otherwise noted)
TYP
(PARAMETER TEST CONDITIONS MIN MAX UNIT1)
RECEIVER
V
IT+
Positive-going differential input voltage threshold 100See Figure 6 and Table 1 mVV
IT-
Negative-going differential input voltage threshold 100V
OH
High-level output voltage I
OH
= -8 mA 2.4 VV
OL
Low-level output voltage I
OL
= 8 mA 0.4 VV
I
= 0 V -24 -40I
I
Input current (Y or Z inputs) µAV
I
= 2.4 V -1.2 -8V
IY
= 0 V and V
IZ
= 100 mV,'LVDM1676 5 10 µAV
IY
= 2.4 V and V
IZ
= 2.3 VI
ID
Differential input current |I
IY
- I
IZ
| (inputs)
V
IY
= 0.2 V and V
IZ
= 0 V,'LVDM1677 1.5 2.2 mAV
IY
= 2.4 V and V
IZ
= 2.2 VI
I(OFF)
Power-off input current (Y or Z inputs) V
CC
= 0 V, V
I
= 2.4 V ±25 µA
(1) All typical values are at 25°C and with a 3.3-V supply.
6
Submit Documentation Feedback
www.ti.com
SWITCHING CHARACTERISTICS
SN65LVDM1676 , SN65LVDM1677
SLLS430B NOVEMBER 2000 REVISED MAY 2004
over recommended operating free-air temperature range (unless otherwise noted)
TYP
(PARAMETER TEST CONDITIONS MIN MAX UNIT1)
DRIVER
t
PLH
Propagation delay time, low-to-high-level output 1.3 2.5 3.6t
PHL
Propagation delay time, high-to-low-level output 1.3 2.5 3.6t
r
Differential output signal rise time 0.5 1.2R
L
= 50 ,t
f
Differential output signal fall time C
L
= 10 pF, 0.5 1.2See Figure 4t
sk(p)
Pulse skew (|t
PHL
- t
PLH
|) 0.1 0.6t
sk(o)
Channel-to-channel output skew
(2)
0.1 0.4 nst
sk(pp)
Part-to-part skew
(3)
1t
PZH
Propagation delay time, high-impedance-to-high-level output 11 20t
PZL
Propagation delay time, high-impedance-to-low-level output 10 20See Figure 5t
PHZ
Propagation delay time, high-level-to-high-impedance output 3 10t
PLZ
Propagation delay time, low-level-to-high-impedance output 3 10
RECEIVER
t
PLH
Propagation delay time, low-to-high-level output 1.5 3 4.5t
PHL
Propagation delay time, high-to-low-level output 1.5 3 4.5t
r
Output signal rise time 0.6 1.6C
L
= 10 pF,t
f
Output signal fall time 0.6 1.6See Figure 7t
sk(p)
Pulse skew (|t
PHL
- t
PLH
|) 0.2 0.8t
sk(o)
Channel-to-channel output skew
(4)
0.7 1.2 nst
sk(pp)
Part-to-part skew
(5)
1t
PZH
Propagation delay time, high-impedance-to-high-level output 9 15t
PZL
Propagation delay time, high-impedance-to-low-level output 8 15See Figure 8t
PHZ
Propagation delay time, high-level-to-high-impedance output 12 20t
PLZ
Propagation delay time, low-level-to-high-impedance output 11 20
(1) All typical values are at 25°C and with a 3.3-V supply.(2) t
sk(o)
is the skew between specified outputs of a single device with all driving inputs connected together and the outputs switching in thesame direction while driving identical specified loads.(3) t
sk(PP)
is the magnitude of the difference in propagation delay times between any specified terminals of two devices when both devicesoperate with the same supply voltages, at the same temperature, and have identical packages and test circuits.(4) t
sk(o)
is the skew between specified outputs of a single device with all driving inputs connected together and the outputs switching in thesame direction while driving identical specified loads.(5) t
sk(pp)
is the magnitude of the difference in propagation delay times between any specified terminals of two devices when both devicesoperate with the same supply voltages, at the same temperature, and have identical packages and test circuits.
7Submit Documentation Feedback
www.ti.com
PARAMETER MEASUREMENT INFORMATION
±
3.75 k
0 V VTEST 2.4 V
Y
ZVOD
Input RL3.75 k
Y
Z
Input
CL = 10 pF
(2 Places)
25 ± 1% (2 Places)
VOC
VOC
VOC(PP) VOC(SS)
0 V
3 V
A
SN65LVDM1676 , SN65LVDM1677
SLLS430B NOVEMBER 2000 REVISED MAY 2004
Figure 1. Driver Voltage and Current Definitions
Figure 2. Driver V
OD
Test Circuit
A. NOTE: All input pulses are supplied by a generator having the following characteristics: t
r
or t
f
1 ns, pulse repetitionrate (PRR) = 0.5 Mpps, pulse width = 500 ± 10 ns. C
L
includes instrumentation and fixture capacitance within 0,06 mof the D.U.T. The measurement of V
OC(PP)
is made on test equipment with a -3 dB bandwidth of at least 300 MHz.
Figure 3. Test Circuit and Definitions for the Driver Common-Mode Output Voltage
8
Submit Documentation Feedback
www.ti.com
Y
ZVOD
Input
CL = 10 pF
(2 Places)
50 ± 1 %
3 V
VCC/2
0 V
tpLH tpHL
100%
80%
20%
0%
Input
Output
0 V
tftr
VOD(H)
VOD(L)
CL = 10 pF
(2 Places)
Y
Z
TX/RX
25 ± 1% (2 Places)
1.2 V
tpZH tpHZ
tpZL tpLZ
3 V
VCC/2
0 V
1.4 V
1.25 V
1.2 V
1 V
1.2 V
1.15 V
TX/RX
VOY or VOZ
VOZ or VOY
VOY VOZ
0.8 V or 2 V
+
SN65LVDM1676 , SN65LVDM1677
SLLS430B NOVEMBER 2000 REVISED MAY 2004
PARAMETER MEASUREMENT INFORMATION (continued)
A. All input pulses are supplied by a generator having the following characteristics: t
r
or t
f
1 ns, pulse repetition rate(PRR) = 0.5 Mpps, pulse width = 10 ± 0.2 ns. C
L
includes instrumentation and fixture capacitance within 0,06 m of theD.U.T.
Figure 4. Test Circuit, Timing, and Voltage Definitions for the Differential Output Signal
A. All input pulses are supplied by a generator having the following characteristics: t
r
or t
f
1 ns, pulse repetition rate(PRR) = 0.5 Mpps, pulse width = 500 ± 10 ns. C
L
includes instrumentation and fixture capacitance within 0,06 m ofthe D.U.T.
Figure 5. Enable and Disable Time Circuit and Definitions
9Submit Documentation Feedback
www.ti.com
VID
Y
Z
Y
VO
VIZ
VIY
VIC
(VIY + VIZ)/2
VID
VO
VIZ
VIY CL = 10 pF
tpHL tpLH
tftr
80%
20%
VIY
VIZ
VID
VO
1.4 V
1 V
0.4 V
0 V
–0.4 V
~VCC
VCC/2
~ 0 V
SN65LVDM1676 , SN65LVDM1677
SLLS430B NOVEMBER 2000 REVISED MAY 2004
PARAMETER MEASUREMENT INFORMATION (continued)
Figure 6. Voltage Definitions
Table 1. Receiver Minimum and Maximum Input Threshold Test Voltages
RESULTING DIFFERENTIAL RESULTING COMMON-APPLIED VOLTAGES
INPUT VOLTAGE MODE INPUT VOLTAGE
V
IY
V
IZ
V
ID
V
IC
1.25 V 1.15 V 100 mV 1.2 V1.15 V 1.25 V -100 mV 1.2 V2.4 V 2.3 V 100 mV 2.35 V2.3 V 2.4 V -100 mV 2.35 V0.1 V 0 V 100 mV 0.05 V0 V 0.1 V -100 mV 0.05 V1.5 V 0.9 V 600 mV 1.2 V0.9 V 1.5 V -600 mV 1.2 V2.4 V 1.8 V 600 mV 2.1 V1.8 V 2.4 V -600 mV 2.1 V0.6 V 0 V 600 mV 0.3 V0 V 0.6 V -600 mV 0.3 V
A. All input pulses are supplied by a generator having the following characteristics: t
r
or t
f
1 ns, pulse repetition rate(PRR) = 0.5 Mpps, pulse width = 10 ± 0.2 ns. C
L
includes instrumentation and fixture capacitance within 0,06 m of theD.U.T.
Figure 7. Timing Test Circuit and Waveforms
10
Submit Documentation Feedback
www.ti.com
Z
Y
VO±
500
VTEST
10 pF
1.2 V
tpZL
tpLZ
2.5 V
1 V
3 V
VCC/2
0 V
2.5 V
VCC/2
VOL
VTEST
Y
TX/RX
A
TX/RX
A
VOL + 0.5 V
tpZH
tpHZ
0 V
1.4 V
3 V
VCC/2
0 V
VOH
VCC/2
0 V
VTEST
Y
TX/RX
AVOH – 0.5 V
NOTE: All input pulses are supplied by a generator having the following
characteristics: tr or tf 1 ns, pulse repetition rate (PRR) = 0.5 Mpps,
pulse width = 500 ± 10 ns. CL includes instrumentation and fixture
capacitance within 0,06 m of the D.U.T.
SN65LVDM1676 , SN65LVDM1677
SLLS430B NOVEMBER 2000 REVISED MAY 2004
Figure 8. Enable/Disable Time Test Circuit and Waveforms
11Submit Documentation Feedback
www.ti.com
TYPICAL CHARACTERISTICS
|VID|− Differential Input Voltage − V
1
00.1 0.3
2
1.5
0.5
0.2 0.4 0.6
2.5
0 0.5
VCC = 3 V
− Common-Mode Input Voltage − V
VIC
VCC > 3.15 V
MIN
IOL − Low-Level Output Current − mA
1
080
2
VCC = 3.3 V
TA = 25°C
3
124
VOL− Low-Level Output Voltage − V
4
6 102
IOH − High-Level Output Current − mA
1
.5
0−4 −6
3
0
1.5
VCC = 3.3 V
TA = 25°C
2
2.5
−8−2
VOH− High-Level Output Voltage − V
3.5
SN65LVDM1676 , SN65LVDM1677
SLLS430B NOVEMBER 2000 REVISED MAY 2004
COMMON-MODE INPUT VOLTAGE
vsDIFFERENTIAL INPUT VOLTAGE
Figure 9.
DRIVER DRIVERLOW-LEVEL OUTPUT VOLTAGE HIGH-LEVEL OUTPUT VOLTAGEvs vsLOW-LEVEL OUTPUT CURRENT HIGH-LEVEL OUTPUT CURRENT
Figure 10. Figure 11.
12
Submit Documentation Feedback
www.ti.com
0IOH − High-Level Output Current − mA
4
0−80
2
−20
VOH
−40 −60
3
1
− High-Level Output Voltage − V
VCC = 3.3 V
TA = 25°C
0IOL − Low-Level Output Current − mA
5
0
2
20
VOL
40 60
3
1
− Low-Level Output Votlage − V
80
4
VCC = 3.3 V
TA = 25°C
TYPICAL CHARACTERISTICS
DRIVER EYE PATTERN
TEST CONDITIONS
SN65LVDM1676 , SN65LVDM1677
SLLS430B NOVEMBER 2000 REVISED MAY 2004
TYPICAL CHARACTERISTICS (continued)
RECEIVER RECEIVERHIGH-LEVEL OUTPUT VOLTAGE LOW-LEVEL OUTPUT VOLTAGEvs vsHIGH-LEVEL OUTPUT CURRENT LOW-LEVEL OUTPUT CURRENT
Figure 12. Figure 13.
V
CC
= 3.3 VT
A
= 25°C (ambient temperature)All 16 channels switching simultaneously with NRZ data. Scope is triggered at the same frequency with pulse. Inputsignal level = 0 to 3 V single ended.Resistive loading with no added capacitance
13Submit Documentation Feedback
www.ti.com
EQUIPMENT
Tektronix PS2521
Programmable
Power Supply
Bench Test Board
Tektronix TDS 784 1 GHz
Oscilloscope
HP E8043A Mainframe System
HPE4841A 660 MHz Data Generator
HPE4841A 660 MHz Data Generator
HPE4841A 660 MHz Data Generator
HPE4841A 660 MHz Data Generator
4
Tektronix P6248
1.7 GHz Differential Probe
4
4
4
100 Mbps 650 Mbps
RECEIVER EYE PATTERN
TEST CONDITIONS
SN65LVDM1676 , SN65LVDM1677
SLLS430B NOVEMBER 2000 REVISED MAY 2004
TYPICAL CHARACTERISTICS (continued)
Figure 14. Driver Test Equipment Setup
Figure 15. Typical Driver Eye Pattern for the SN65LVDM1676
V
CC
= 3.3 VT
A
= 25°C (ambient temperature)All 16 channels switching simultaneously with NRZ data. Scope is pulse-triggered simultaneously with NRZ data. Inputsignal level is 1 V to 1.4 V differential.50- resistive loading with no added capacitance
14
Submit Documentation Feedback
www.ti.com
EQUIPMENT
Tektronix PS2521
Programmable
Power Supply
Bench Test Board
Tektronix TDS 784 1 GHz
Oscilloscope
HP E8043A Mainframe System
HPE4841A 660 MHz Data Generator
HPE4841A 660 MHz Data Generator
HPE4841A 660 MHz Data Generator
HPE4841A 660 MHz Data Generator
8
Tektronix P6248
1.7 GHz Differential Probe
8
8
8
100 Mbps 350 Mbps
SN65LVDM1676 , SN65LVDM1677
SLLS430B NOVEMBER 2000 REVISED MAY 2004
TYPICAL CHARACTERISTICS (continued)
Figure 16. Receiver Test Equipment Setup
Figure 17. Typical Receiver Eye Pattern for the SN65LVDM1677
15Submit Documentation Feedback
www.ti.com
APPLICATION INFORMATION
FAIL SAFE
Rt = 100 (Typ)
300 k300 k
VCC
VIT 2.3 V
A
BY
SN65LVDM1676 , SN65LVDM1677
SLLS430B NOVEMBER 2000 REVISED MAY 2004
One of the most common problems with differential signaling applications is how the system responds when nodifferential voltage is present on the signal pair. The LVDS receiver is like most differential line receivers, in thatits output logic state can be indeterminate when the differential input voltage is between -50 mV and 50 mV andwithin its recommended input common-mode voltage range. TI's LVDS receiver is different, however, in how ithandles the open-input circuit situation.
Open-circuit means that there is little or no input current to the receiver from the data line itself. This could bewhen the driver is in a high-impedance state or the cable is disconnected. When this occurs, the LVDS receiverwill pull each line of the signal pair to near V
CC
through 300-k resistors as shown in Figure 18. The fail-safefeature uses an AND gate with input voltage thresholds at about 2.3 V to detect this condition and force theoutput to a high-level, regardless of the differential input voltage.
Figure 18. Open-Circuit Fail Safe of the LVDS Receiver
It is only under these conditions that the output of the receiver will be valid with less than a 50-mV differentialinput voltage magnitude. The presence of the termination resistor, Rt, does not affect the fail-safe function aslong as it is connected as shown in the figure. Other termination circuits may allow a dc current to ground thatcould defeat the pullup currents from the receiver and the fail-safe feature.
16
Submit Documentation Feedback
PACKAGING INFORMATION
Orderable Device Status (1) Package
Type Package
Drawing Pins Package
Qty Eco Plan (2) Lead/Ball Finish MSL Peak Temp (3)
SN65LVDM1676DGG ACTIVE TSSOP DGG 64 25 Green (RoHS &
no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR
SN65LVDM1676DGGG4 ACTIVE TSSOP DGG 64 25 Green (RoHS &
no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR
SN65LVDM1676DGGR ACTIVE TSSOP DGG 64 2000 Green (RoHS &
no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR
SN65LVDM1676DGGRG4 ACTIVE TSSOP DGG 64 2000 Green (RoHS &
no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR
SN65LVDM1677DGG ACTIVE TSSOP DGG 64 25 Green (RoHS &
no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR
SN65LVDM1677DGGG4 ACTIVE TSSOP DGG 64 25 Green (RoHS &
no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR
SN65LVDM1677DGGR ACTIVE TSSOP DGG 64 2000 Green (RoHS &
no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR
SN65LVDM1677DGGRG4 ACTIVE TSSOP DGG 64 2000 Green (RoHS &
no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS) or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
PACKAGE OPTION ADDENDUM
www.ti.com 17-Nov-2005
Addendum-Page 1
MECHANICAL DATA
MTSS003D – JANUARY 1995 – REVISED JANUAR Y 1998
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
DGG (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE
4040078/F 12/97
48 PINS SHOWN
0,25
0,15 NOM
Gage Plane
6,00
6,20 8,30
7,90
0,75
0,50
Seating Plane
25
0,27
0,17
24
A
48
1
1,20 MAX
M
0,08
0,10
0,50
0°–8°
56
14,10
13,90
48
DIM
A MAX
A MIN
PINS **
12,40
12,60
64
17,10
16,90
0,15
0,05
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
C. Body dimensions do not include mold protrusion not to exceed 0,15.
D. Falls within JEDEC MO-153
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’s terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process
in which TI products or services are used. Information published by TI regarding third-party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Following are URLs where you can obtain information on other Texas Instruments products and application
solutions:
Products Applications
Amplifiers amplifier.ti.com Audio www.ti.com/audio
Data Converters dataconverter.ti.com Automotive www.ti.com/automotive
DSP dsp.ti.com Broadband www.ti.com/broadband
Interface interface.ti.com Digital Control www.ti.com/digitalcontrol
Logic logic.ti.com Military www.ti.com/military
Power Mgmt power.ti.com Optical Networking www.ti.com/opticalnetwork
Microcontrollers microcontroller.ti.com Security www.ti.com/security
Telephony www.ti.com/telephony
Video & Imaging www.ti.com/video
Wireless www.ti.com/wireless
Mailing Address: Texas Instruments
Post Office Box 655303 Dallas, Texas 75265
Copyright 2006, Texas Instruments Incorporated