INTEGRATED CIRCUITS DATA SHEET PCF8591 8-bit A/D and D/A converter Product specification Supersedes data of 1998 Jul 02 File under Integrated Circuits, IC12 2001 Dec 13 Philips Semiconductors Product specification 8-bit A/D and D/A converter PCF8591 CONTENTS 1 FEATURES 2 APPLICATIONS 3 GENERAL DESCRIPTION 4 ORDERING INFORMATION 5 BLOCK DIAGRAM 6 PINNING 7 FUNCTIONAL DESCRIPTION 7.1 7.2 7.3 7.4 7.5 7.6 Addressing Control byte D/A conversion A/D conversion Reference voltage Oscillator 8 CHARACTERISTICS OF THE I2C-BUS 8.1 8.2 8.3 8.4 8.5 Bit transfer Start and stop conditions System configuration Acknowledge I2C-bus protocol 9 LIMITING VALUES 10 HANDLING 11 DC CHARACTERISTICS 12 D/A CHARACTERISTICS 13 A/D CHARACTERISTICS 14 AC CHARACTERISTICS 15 APPLICATION INFORMATION 16 PACKAGE OUTLINES 17 SOLDERING 17.1 17.2 17.2.1 17.2.2 17.3 17.3.1 17.3.2 17.3.3 Introduction DIP Soldering by dipping or by wave Repairing soldered joints SO Reflow soldering Wave soldering Repairing soldered joints 18 DEFINITIONS 19 LIFE SUPPORT APPLICATIONS 20 PURCHASE OF PHILIPS I2C COMPONENTS 2001 Dec 13 2 Philips Semiconductors Product specification 8-bit A/D and D/A converter 1 PCF8591 FEATURES * Single power supply * Operating supply voltage 2.5 V to 6 V * Low standby current * Serial input/output via I2C-bus * Address by 3 hardware address pins 3 * Sampling rate given by The PCF8591 is a single-chip, single-supply low power 8-bit CMOS data acquisition device with four analog inputs, one analog output and a serial I2C-bus interface. Three address pins A0, A1 and A2 are used for programming the hardware address, allowing the use of up to eight devices connected to the I2C-bus without additional hardware. Address, control and data to and from the device are transferred serially via the two-line bidirectional I2C-bus. I2C-bus speed * 4 analog inputs programmable as single-ended or differential inputs * Auto-incremented channel selection * Analog voltage range from VSS to VDD * On-chip track and hold circuit * 8-bit successive approximation A/D conversion * Multiplying DAC with one analog output. 2 GENERAL DESCRIPTION The functions of the device include analog input multiplexing, on-chip track and hold function, 8-bit analog-to-digital conversion and an 8-bit digital-to-analog conversion. The maximum conversion rate is given by the maximum speed of the I2C-bus. APPLICATIONS * Closed loop control systems * Low power converter for remote data acquisition * Battery operated equipment * Acquisition of analog values in automotive, audio and TV applications. 4 ORDERING INFORMATION TYPE NUMBER PACKAGE NAME DESCRIPTION VERSION PCF8591P DIP16 plastic dual in-line package; 16 leads (300 mil); long body SOT38-1 PCF8591T SO16 plastic small outline package; 16 leads; body width 7.5 mm SOT162-1 2001 Dec 13 3 This text is here in white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader.This text is here in _white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader.This text is here inThis text is here in white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader. white to force landscape pages to be ... 8-bit A/D and D/A converter BLOCK DIAGRAM Philips Semiconductors 5 2001 Dec 13 4 Product specification PCF8591 Fig.1 Block diagram. Philips Semiconductors Product specification 8-bit A/D and D/A converter 6 PCF8591 PINNING SYMBOL PIN DESCRIPTION AINO 1 AIN1 2 AIN2 3 AIN3 4 A0 5 A1 6 A2 7 VSS 8 negative supply voltage SDA 9 I2C-bus data input/output SCL 10 I2C-bus clock input OSC 11 oscillator input/output EXT 12 external/internal switch for oscillator input analog inputs (A/D converter) hardware address AGND 13 analog ground VREF 14 voltage reference input AOUT 15 analog output (D/A converter) VDD 16 positive supply voltage 2001 Dec 13 Fig.2 Pinning diagram. 5 Philips Semiconductors Product specification 8-bit A/D and D/A converter 7 7.1 PCF8591 FUNCTIONAL DESCRIPTION 7.2 Addressing Control byte The second byte sent to a PCF8591 device will be stored in its control register and is required to control the device function. Each PCF8591 device in an I2C-bus system is activated by sending a valid address to the device. The address consists of a fixed part and a programmable part. The programmable part must be set according to the address pins A0, A1 and A2. The address always has to be sent as the first byte after the start condition in the I2C-bus protocol. The last bit of the address byte is the read/write-bit which sets the direction of the following data transfer (see Figs 3, 15 and 16). The upper nibble of the control register is used for enabling the analog output, and for programming the analog inputs as single-ended or differential inputs. The lower nibble selects one of the analog input channels defined by the upper nibble (see Fig.4). If the auto-increment flag is set the channel number is incremented automatically after each A/D conversion. If the auto-increment mode is desired in applications where the internal oscillator is used, the analog output enable flag in the control byte (bit 6) should be set. This allows the internal oscillator to run continuously, thereby preventing conversion errors resulting from oscillator start-up delay. The analog output enable flag may be reset at other times to reduce quiescent power consumption. Fig.3 Address byte. 2001 Dec 13 The selection of a non-existing input channel results in the highest available channel number being allocated. Therefore, if the auto-increment flag is set, the next selected channel will be always channel 0. The most significant bits of both nibbles are reserved for future functions and have to be set to 0. After a Power-on reset condition all bits of the control register are reset to 0. The D/A converter and the oscillator are disabled for power saving. The analog output is switched to a high-impedance state. 6 Philips Semiconductors Product specification 8-bit A/D and D/A converter PCF8591 Fig.4 Control byte. 2001 Dec 13 7 Philips Semiconductors Product specification 8-bit A/D and D/A converter 7.3 PCF8591 D/A conversion The on-chip D/A converter is also used for successive approximation A/D conversion. In order to release the DAC for an A/D conversion cycle the unity gain amplifier is equipped with a track and hold circuit. This circuit holds the output voltage while executing the A/D conversion. The third byte sent to a PCF8591 device is stored in the DAC data register and is converted to the corresponding analog voltage using the on-chip D/A converter. This D/A converter consists of a resistor divider chain connected to the external reference voltage with 256 taps and selection switches. The tap-decoder switches one of these taps to the DAC output line (see Fig.5). The output voltage supplied to the analog output AOUT is given by the formula shown in Fig.6. The waveforms of a D/A conversion sequence are shown in Fig.7. The analog output voltage is buffered by an auto-zeroed unity gain amplifier. This buffer amplifier may be switched on or off by setting the analog output enable flag of the control register. In the active state the output voltage is held until a further data byte is sent. Fig.5 DAC resistor divider chain. 2001 Dec 13 8 Philips Semiconductors Product specification 8-bit A/D and D/A converter PCF8591 Fig.6 DAC data and DC conversion characteristics. Fig.7 D/A conversion sequence. 2001 Dec 13 9 Philips Semiconductors Product specification 8-bit A/D and D/A converter 7.4 PCF8591 A/D conversion The conversion result is stored in the ADC data register and awaits transmission. If the auto-increment flag is set the next channel is selected. The A/D converter makes use of the successive approximation conversion technique. The on-chip D/A converter and a high-gain comparator are used temporarily during an A/D conversion cycle. The first byte transmitted in a read cycle contains the conversion result code of the previous read cycle. After a Power-on reset condition the first byte read is a hexadecimal 80. The protocol of an I2C-bus read cycle is shown in Chapter 8, Figs 15 and 16. An A/D conversion cycle is always started after sending a valid read mode address to a PCF8591 device. The A/D conversion cycle is triggered at the trailing edge of the acknowledge clock pulse and is executed while transmitting the result of the previous conversion (see Fig.8). The maximum A/D conversion rate is given by the actual speed of the I2C-bus. Once a conversion cycle is triggered an input voltage sample of the selected channel is stored on the chip and is converted to the corresponding 8-bit binary code. Samples picked up from differential inputs are converted to an 8-bit two's complement code (see Figs 9 and 10). Fig.8 A/D conversion sequence. 2001 Dec 13 10 Philips Semiconductors Product specification 8-bit A/D and D/A converter PCF8591 Fig.9 A/D conversion characteristics of single-ended inputs. Fig.10 A/D conversion characteristics of differential inputs. 2001 Dec 13 11 Philips Semiconductors Product specification 8-bit A/D and D/A converter 7.5 PCF8591 7.6 Reference voltage Oscillator For the D/A and A/D conversion either a stable external voltage reference or the supply voltage has to be applied to the resistor divider chain (pins VREF and AGND). The AGND pin has to be connected to the system analog ground and may have a DC off-set with reference to VSS. An on-chip oscillator generates the clock signal required for the A/D conversion cycle and for refreshing the auto-zeroed buffer amplifier. When using this oscillator the EXT pin has to be connected to VSS. At the OSC pin the oscillator frequency is available. A low frequency may be applied to the VREF and AGND pins. This allows the use of the D/A converter as a one-quadrant multiplier; see Chapter 15 and Fig.6. If the EXT pin is connected to VDD the oscillator output OSC is switched to a high-impedance state allowing the user to feed an external clock signal to OSC. The A/D converter may also be used as a one or two quadrant analog divider. The analog input voltage is divided by the reference voltage. The result is converted to a binary code. In this application the user has to keep the reference voltage stable during the conversion cycle. 2001 Dec 13 12 Philips Semiconductors Product specification 8-bit A/D and D/A converter 8 PCF8591 CHARACTERISTICS OF THE I2C-BUS The I2C-bus is for bidirectional, two-line communication between different ICs or modules. The two lines are a serial data line (SDA) and a serial clock line (SCL). Both lines must be connected to a positive supply via a pull-up resistor. Data transfer may be initiated only when the bus is not busy. 8.1 Bit transfer One data bit is transferred during each clock pulse. The data on the SDA line must remain stable during the HIGH period of the clock pulse as changes in the data line at this time will be interpreted as a control signal. handbook, full pagewidth SDA SCL data line stable; data valid change of data allowed MBC621 Fig.11 Bit transfer. 8.2 Start and stop conditions Both data and clock lines remain HIGH when the bus is not busy. A HIGH-to-LOW transition of the data line, while the clock is HIGH, is defined as the start condition (S). A LOW-to-HIGH transition of the data line while the clock is HIGH, is defined as the stop condition (P). handbook, full pagewidth SDA SDA SCL SCL S P START condition STOP condition MBC622 Fig.12 Definition of START and STOP condition. 8.3 System configuration A device generating a message is a `transmitter', a device receiving a message is the `receiver'. The device that controls the message is the `master' and the devices which are controlled by the master are the `slaves'. 2001 Dec 13 13 Philips Semiconductors Product specification 8-bit A/D and D/A converter PCF8591 SDA SCL MASTER TRANSMITTER / RECEIVER SLAVE TRANSMITTER / RECEIVER SLAVE RECEIVER MASTER TRANSMITTER MASTER TRANSMITTER / RECEIVER MBA605 Fig.13 System configuration. 8.4 Acknowledge The number of data bytes transferred between the start and stop conditions from transmitter to receiver is not limited. Each data byte of eight bits is followed by one acknowledge bit. The acknowledge bit is a HIGH level put on the bus by the transmitter whereas the master also generates an extra acknowledge related clock pulse. A slave receiver which is addressed must generate an acknowledge after the reception of each byte. Also a master must generate an acknowledge after the reception of each byte that has been clocked out of the slave transmitter. The device that acknowledges has to pull down the SDA line during the acknowledge clock pulse, so that the SDA line is stable LOW during the HIGH period of the acknowledge related clock pulse. A master receiver must signal an end of data to the transmitter by not generating an acknowledge on the last byte that has been clocked out of the slave. In this event the transmitter must leave the data line HIGH to enable the master to generate a stop condition. handbook, full pagewidth DATA OUTPUT BY TRANSMITTER not acknowledge DATA OUTPUT BY RECEIVER acknowledge SCL FROM MASTER 1 2 8 9 S clock pulse for acknowledgement START condition MBC602 Fig.14 Acknowledgement on the I2C-bus. 2001 Dec 13 14 Philips Semiconductors Product specification 8-bit A/D and D/A converter 8.5 PCF8591 I2C-bus protocol After a start condition a valid hardware address has to be sent to a PCF8591 device. The read/write bit defines the direction of the following single or multiple byte data transfer. For the format and the timing of the start condition (S), the stop condition (P) and the acknowledge bit (A) refer to the I2C-bus characteristics. In the write mode a data transfer is terminated by sending either a stop condition or the start condition of the next data transfer. Fig.15 Bus protocol for write mode, D/A conversion. Fig.16 Bus protocol for read mode, A/D conversion. 2001 Dec 13 15 Philips Semiconductors Product specification 8-bit A/D and D/A converter PCF8591 9 LIMITING VALUES In accordance with the Absolute Maximum Rating System (IEC 134). SYMBOL PARAMETER MIN. MAX. UNIT VDD supply voltage (pin 16) -0.5 +8.0 V VI input voltage (any input) -0.5 VDD + 0.5 V II DC input current - 10 mA IO DC output current - 20 mA IDD, ISS VDD or VSS current - 50 mA Ptot total power dissipation per package - 300 mW PO power dissipation per output - 100 mW Tamb operating ambient temperature -40 +85 C Tstg storage temperature -65 +150 C 10 HANDLING Inputs and outputs are protected against electrostatic discharge in normal handling. However, to be totally safe, it is desirable to take precautions appropriate to handling MOS devices. Advice can be found in Data Handbook IC12 under "Handling MOS Devices". 2001 Dec 13 16 Philips Semiconductors Product specification 8-bit A/D and D/A converter PCF8591 11 DC CHARACTERISTICS VDD = 2.5 V to 6 V; VSS = 0 V; Tamb = -40 C to +85 C unless otherwise specified. SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT Supply VDD supply voltage (operating) IDD supply current VPOR 2.5 - 6.0 V standby VI = VSS or VDD; no load - 1 15 A operating, AOUT off fSCL = 100 kHz - 125 250 A operating, AOUT active fSCL = 100 kHz - 0.45 1.0 mA note 1 0.8 - 2.0 V Power-on reset level Digital inputs/output: SCL, SDA, A0, A1, A2 VIL LOW level input voltage 0 - 0.3 x VDD V VIH HIGH level input voltage 0.7 x VDD - VDD V IL leakage current A0, A1, A2 VI = VSS to VDD -250 - +250 nA SCL, SDA VI = VSS to VDD -1 - +1 A Ci input capacitance - - 5 pF IOL LOW level SDA output current VOL = 0.4 V 3.0 - - mA VSS + 1.6 - VDD V Reference voltage inputs VREF reference voltage VREF > VAGND; note 2 VAGND analog ground voltage VREF > VAGND; note 2 ILI input leakage current RREF input resistance pins VREF and AGND VSS - VDD - 0.8 V -250 - +250 nA - 100 - k Oscillator: OSC, EXT ILI input leakage current - - 250 nA fOSC oscillator frequency 0.75 - 1.25 MHz Notes 1. The power on reset circuit resets the I2C-bus logic when VDD is less than VPOR. 2. A further extension of the range is possible, if the following conditions are fulfilled: V REF + V AGND V REF + V AGND -------------------------------------- 0.8V, V DD - -------------------------------------- 0.4V 2 2 2001 Dec 13 17 Philips Semiconductors Product specification 8-bit A/D and D/A converter PCF8591 12 D/A CHARACTERISTICS VDD = 5.0 V; VSS = 0 V; VREF = 5.0 V; VAGND = 0 V; RL = 10 k; CL = 100 pF; Tamb = -40 C to +85 C unless otherwise specified. SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT Analog output VOA output voltage ILO output leakage current no resistive load VSS - RL = 10 k VSS AOUT disabled - Tamb = 25 C VDD V - 0.9 x VDD V - 250 nA - - 50 mV - - 1.5 LSB - - 1 % Accuracy OSe offset error Le linearity error Ge gain error tDAC settling time fDAC conversion rate SNRR supply noise rejection ratio no resistive load to 1 LSB 2 full scale step f = 100 Hz; VDDN = 0.1 x VPP - - 90 s - - 11.1 kHz - 40 - dB 13 A/D CHARACTERISTICS VDD = 5.0 V; VSS = 0 V; VREF = 5.0 V; VAGND = 0 V; RS = 10 k; Tamb = -40 C to +85 C unless otherwise specified. SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT Analog inputs VIA analog input voltage VSS - VDD V ILIA analog input leakage current - - 100 nA CIA analog input capacitance - 10 - pF CID differential input capacitance - 10 - pF VIS single-ended voltage measuring range VAGND - VREF V VID differential voltage measuring range; VFS = VREF - VAGND - V FS ------------2 - +V FS -------------2 V OSe offset error Tamb = 25 C - - 20 mV Le linearity error - - 1.5 LSB Ge gain error - - 1 % GSe small-signal gain error - - 5 % CMRR common-mode rejection ratio - 60 - dB SNRR supply noise rejection ratio - 40 - dB tADC conversion time - - 90 s fADC sampling/conversion rate - - 11.1 kHz Accuracy 2001 Dec 13 Vi = 16 LSB f = 100 Hz; VDDN = 0.1 x VPP 18 Philips Semiconductors Product specification 8-bit A/D and D/A converter PCF8591 (a) Internal oscillator; Tamb = +27 C. (b) External oscillator. Fig.17 Operating supply current as a function of supply voltage (analog output disabled). (a) Output impedance near negative power rail; Tamb = +27 C. (b) Output impedance near positive power rail; Tamb = +27 C. The x-axis represents the hex input-code equivalent of the output voltage. Fig.18 Output impedance of analog output buffer (near power rails). 2001 Dec 13 19 Philips Semiconductors Product specification 8-bit A/D and D/A converter PCF8591 14 AC CHARACTERISTICS All timing values are valid within the operating supply voltage and ambient temperature range and reference to VIL and VIH with an input voltage swing of VSS to VDD. SYMBOL PARAMETER MIN. TYP. MAX. UNIT I2C-bus timing (see Fig.19; note 1) fSCL SCL clock frequency - - 100 kHz tSP tolerable spike width on bus - - 100 ns tBUF bus free time 4.7 - - s tSU;STA START condition set-up time 4.7 - - s tHD;STA START condition hold time 4.0 - - s tLOW SCL LOW time 4.7 - - s tHIGH SCL HIGH time 4.0 - - s tr SCL and SDA rise time - - 1.0 s tf SCL and SDA fall time - - 0.3 s tSU;DAT data set-up time 250 - - ns tHD;DAT data hold time 0 - - ns tVD;DAT SCL LOW-to-data out valid - - 3.4 s tSU;STO STOP condition set-up time 4.0 - - s Note 1. A detailed description of the I2C-bus specification, with applications, is given in brochure "The I2C-bus and how to use it". This brochure may be ordered using the code 9398 393 40011. handbook, full pagewidth t SU;STA BIT 6 (A6) BIT 7 MSB (A7) START CONDITION (S) PROTOCOL t LOW t HIGH BIT 0 LSB (R/W) ACKNOWLEDGE (A) STOP CONDITION (P) 1 / f SCL SCL t tr BUF t f SDA t HD;STA t SU;DAT t HD;DAT t VD;DAT MBD820 Fig.19 I2C-bus timing diagram; rise and fall times refer to VIL and VIH. 2001 Dec 13 20 t SU;STO Philips Semiconductors Product specification 8-bit A/D and D/A converter PCF8591 15 APPLICATION INFORMATION Inputs must be connected to VSS or VDD when not in use. Analog inputs may also be connected to AGND or VREF. In order to prevent excessive ground and supply noise and to minimize cross-talk of the digital to analog signal paths the user has to design the printed-circuit board layout very carefully. Supply lines common to a PCF8591 device and noisy digital circuits and ground loops should be avoided. Decoupling capacitors (>10 F) are recommended for power supply and reference voltage inputs. Fig.20 Application diagram. 2001 Dec 13 21 Philips Semiconductors Product specification 8-bit A/D and D/A converter PCF8591 16 PACKAGE OUTLINES DIP16: plastic dual in-line package; 16 leads (300 mil); long body SOT38-1 ME seating plane D A2 A A1 L c e Z b1 w M (e 1) b MH 9 16 pin 1 index E 1 8 0 5 10 mm scale DIMENSIONS (inch dimensions are derived from the original mm dimensions) UNIT A max. A1 min. A2 max. b b1 c D (1) E (1) e e1 L ME MH w Z (1) max. mm 4.7 0.51 3.7 1.40 1.14 0.53 0.38 0.32 0.23 21.8 21.4 6.48 6.20 2.54 7.62 3.9 3.4 8.25 7.80 9.5 8.3 0.254 2.2 inches 0.19 0.020 0.15 0.055 0.045 0.021 0.015 0.013 0.009 0.86 0.84 0.26 0.24 0.10 0.30 0.15 0.13 0.32 0.31 0.37 0.33 0.01 0.087 Note 1. Plastic or metal protrusions of 0.25 mm maximum per side are not included. REFERENCES OUTLINE VERSION IEC JEDEC EIAJ SOT38-1 050G09 MO-001 SC-503-16 2001 Dec 13 22 EUROPEAN PROJECTION ISSUE DATE 95-01-19 99-12-27 Philips Semiconductors Product specification 8-bit A/D and D/A converter PCF8591 SO16: plastic small outline package; 16 leads; body width 7.5 mm SOT162-1 D E A X c HE y v M A Z 9 16 Q A2 A (A 3) A1 pin 1 index Lp L 1 8 e detail X w M bp 0 5 10 mm scale DIMENSIONS (inch dimensions are derived from the original mm dimensions) UNIT A max. A1 A2 A3 bp c D (1) E (1) e HE L Lp Q v w y mm 2.65 0.30 0.10 2.45 2.25 0.25 0.49 0.36 0.32 0.23 10.5 10.1 7.6 7.4 1.27 10.65 10.00 1.4 1.1 0.4 1.1 1.0 0.25 0.25 0.1 0.9 0.4 inches 0.10 0.012 0.096 0.004 0.089 0.01 0.019 0.013 0.014 0.009 0.41 0.40 0.30 0.29 0.050 0.419 0.043 0.055 0.394 0.016 0.043 0.039 0.01 0.01 0.004 0.035 0.016 Z (1) 8o 0o Note 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. REFERENCES OUTLINE VERSION IEC JEDEC SOT162-1 075E03 MS-013 2001 Dec 13 EIAJ EUROPEAN PROJECTION ISSUE DATE 97-05-22 99-12-27 23 Philips Semiconductors Product specification 8-bit A/D and D/A converter PCF8591 Several techniques exist for reflowing; for example, thermal conduction by heated belt. Dwell times vary between 50 and 300 seconds depending on heating method. Typical reflow temperatures range from 215 to 250 C. 17 SOLDERING 17.1 Introduction There is no soldering method that is ideal for all IC packages. Wave soldering is often preferred when through-hole and surface mounted components are mixed on one printed-circuit board. However, wave soldering is not always suitable for surface mounted ICs, or for printed-circuits with high population densities. In these situations reflow soldering is often used. Preheating is necessary to dry the paste and evaporate the binding agent. Preheating duration: 45 minutes at 45 C. 17.3.2 This text gives a very brief insight to a complex technology. A more in-depth account of soldering ICs can be found in our "Data Handbook IC26; Integrated Circuit Packages" (order code 9398 652 90011). 17.2 17.2.1 Wave soldering techniques can be used for all SO packages if the following conditions are observed: * A double-wave (a turbulent wave with high upward pressure followed by a smooth laminar wave) soldering technique should be used. DIP * The longitudinal axis of the package footprint must be parallel to the solder flow. SOLDERING BY DIPPING OR BY WAVE The maximum permissible temperature of the solder is 260 C; solder at this temperature must not be in contact with the joint for more than 5 seconds. The total contact time of successive solder waves must not exceed 5 seconds. * The package footprint must incorporate solder thieves at the downstream end. During placement and before soldering, the package must be fixed with a droplet of adhesive. The adhesive can be applied by screen printing, pin transfer or syringe dispensing. The package can be soldered after the adhesive is cured. The device may be mounted up to the seating plane, but the temperature of the plastic body must not exceed the specified maximum storage temperature (Tstg max). If the printed-circuit board has been pre-heated, forced cooling may be necessary immediately after soldering to keep the temperature within the permissible limit. 17.2.2 Maximum permissible solder temperature is 260 C, and maximum duration of package immersion in solder is 10 seconds, if cooled to less than 150 C within 6 seconds. Typical dwell time is 4 seconds at 250 C. REPAIRING SOLDERED JOINTS A mildly-activated flux will eliminate the need for removal of corrosive residues in most applications. Apply a low voltage soldering iron (less than 24 V) to the lead(s) of the package, below the seating plane or not more than 2 mm above it. If the temperature of the soldering iron bit is less than 300 C it may remain in contact for up to 10 seconds. If the bit temperature is between 300 and 400 C, contact may be up to 5 seconds. 17.3 17.3.1 17.3.3 REPAIRING SOLDERED JOINTS Fix the component by first soldering two diagonallyopposite end leads. Use only a low voltage soldering iron (less than 24 V) applied to the flat part of the lead. Contact time must be limited to 10 seconds at up to 300 C. When using a dedicated tool, all other leads can be soldered in one operation within 2 to 5 seconds between 270 and 320 C. SO REFLOW SOLDERING Reflow soldering techniques are suitable for all SO packages. Reflow soldering requires solder paste (a suspension of fine solder particles, flux and binding agent) to be applied to the printed-circuit board by screen printing, stencilling or pressure-syringe dispensing before package placement. 2001 Dec 13 WAVE SOLDERING 24 Philips Semiconductors Product specification 8-bit A/D and D/A converter PCF8591 18 DATA SHEET STATUS DATA SHEET STATUS(1) PRODUCT STATUS(2) DEFINITIONS Objective data Development This data sheet contains data from the objective specification for product development. Philips Semiconductors reserves the right to change the specification in any manner without notice. Preliminary data Qualification This data sheet contains data from the preliminary specification. Supplementary data will be published at a later date. Philips Semiconductors reserves the right to change the specification without notice, in order to improve the design and supply the best possible product. Product data Production This data sheet contains data from the product specification. Philips Semiconductors reserves the right to make changes at any time in order to improve the design, manufacturing and supply. Changes will be communicated according to the Customer Product/Process Change Notification (CPCN) procedure SNW-SQ-650A. Notes 1. Please consult the most recently issued data sheet before initiating or completing a design. 2. The product status of the device(s) described in this data sheet may have changed since this data sheet was published. The latest information is available on the Internet at URL http://www.semiconductors.philips.com. 19 DEFINITIONS 20 DISCLAIMERS Short-form specification The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Life support applications These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Limiting values definition Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 60134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Right to make changes Philips Semiconductors reserves the right to make changes, without notice, in the products, including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no licence or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Application information Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification. 2001 Dec 13 25 Philips Semiconductors Product specification 8-bit A/D and D/A converter PCF8591 21 PURCHASE OF PHILIPS I2C COMPONENTS Purchase of Philips I2C components conveys a license under the Philips' I2C patent to use the components in the I2C system provided the system conforms to the I2C specification defined by Philips. This specification can be ordered using the code 9398 393 40011. 2001 Dec 13 26 Philips Semiconductors Product specification 8-bit A/D and D/A converter PCF8591 NOTES 2001 Dec 13 27 Philips Semiconductors - a worldwide company Contact information For additional information please visit http://www.semiconductors.philips.com. Fax: +31 40 27 24825 For sales offices addresses send e-mail to: sales.addresses@www.semiconductors.philips.com. SCA73 (c) Koninklijke Philips Electronics N.V. 2001 All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent- or other industrial or intellectual property rights. Printed in The Netherlands 403512/05/pp28 Date of release: 2001 Dec 13 Document order number: 9397 750 09201