HI-SINCERITY Spec. No. : IC200409 Issued Date : 2004.05.01 Revised Date : 2004.05.14 Page No. : 1/7 MICROELECTRONICS CORP. HLM358P / HLM358S LOW POWER DUAL OPERATIONAL AMPLIFIERS 8-Lead Plastic DIP-8 Package Code: P Description These devices consist of two independent, high gain, internally frequencycompensated operational amplifiers designed operate from a single supply over a wide range of voltages. Operation from split supplies also is possible if the difference between the two supplies is 3V to 32V, and Vcc is at least 1.5V more positive than the input common-mode voltage, The low supply-current drain is independent of the magnitude of the power supply voltage. * 8-Lead Plastic SO-8 Package Code: S Features Logic Diagram (each amplifier) * Two internally compensated OP amps * Internally frequency compensated for unity gain IN + + IN - - OUTPUT * Short Circuit Protected Outputs * Wide power supply range: 3VDC to 32VDC (Single supply) * Input common-mode voltage range includes ground * Large output voltage swing: 0VDC to Vcc-1.5VDC Pin Configurations Pin 1: Output 1 Pin 5 : Non Inverting Input 2 Pin 2: Inverting Input 1 Pin 6 : Inverting Input 2 Pin 3: Non Inverting Input 1 Pin 7 : Output 2 Pin 4: VEE Pin 8 : Vcc 8 1 2 - 3 + 7 Out - 6 + 5 Out 4 Schematic Diagram Vcc 6uA 100uA Q5 6uA Q6 Cc Q7 Rsc Q2 Inverting Input Q3 Q4 Q1 Output Q11 Q13 + Non Inverting Input Q10 Q8 HLM358P, HLM358S Q12 50uA Q9 HSMC Product Specification HI-SINCERITY Spec. No. : IC200409 Issued Date : 2004.05.01 Revised Date : 2004.05.14 Page No. : 2/7 MICROELECTRONICS CORP. Absolute Maximum Ratings (Ta=25oC, unless otherwise specified) Symbol Parameter Range Units VCC Power Supply Voltage (Single Supply) 32 VDC VCC, VEE Power Supply Voltage (Split Supplies) 16 VDC VIDR Input Differential Voltage Range 32 VDC VICR Input Common Mode Voltage Range -0.3 to +32 VDC tSC Output Short Circuit Duration Continuous TJ Junction Temperature Tstg Storage Temperature Range TA Operating Ambient Temperature Range PD Maximum Power Dissipation (DIP-8) Maximum Power Dissipation (SO-8) o 150 C -55 to +125 C 0 to +70 C 800 500 mW Electrical Characteristics (VCC=5V, VEE=Ground, Ta=25oC, unless otherwise specified) Symbol Parameter Test Conditions HLM358P/S Min Typ Max Unit VIO Input Offset Voltage VCC=5V~30V, VICR=0V~VCC-1.5V, VO=1.4V, RS=0 - 2 7 mV IIO Input Offset Current IIN(+)-IIN(-) - - 30 nA IIB Input Bias Current IIN(+) or IIN(-) - 35 200 nA AVOL Large Signal Voltage Gain VCC=15V, RL=2K 25 100 - V/mV CMR Common-Mode Rejection Ratio VCM=0V~VCC-1.5V 65 85 - dB Channel Separation 1KHzf20KHz - -120 - dB Power Supply Rejection VCC=5V~30V 65 100 - dB VIO/T Average Temperature Coefficient of Input Offset Voltage RS=0 - 7 - uV/oC IIO/T Average Temperature Coefficient of Input Offset Current RS=0 - 10 - pA/oC VICR Input Common Mode Voltage Range VCC=30V VCC-2V V VOH Output Voltage (High Limit) VOL Output Voltage (Low Limit) ICC CS PSR VCC=30V, RL=2K 26 27 - VCC=30V, RL=10K 27 28 - RL=10K - 5 20 mV Supply current RL=,VCC=30V - 1 2 mA Output Source Current VCC=15V, VIN+=1V, VIN-=0V, VO=2V 20 40 - mA ISink Output Sink Current VCC=15V, VIN+=0V, VIN-=1V, VO=2V 10 20 - mA ICC Power Supply Current VCC=30V, Ta=Thigh to Tlow - 1 2 mA VCC=5V, Ta=Thigh to Tlow - 0.6 1.2 mA ISC Output Short Circuit to Ground VCC=5V, GND at -5V, VO=0V - 40 60 mA ISource HLM358P, HLM358S V HSMC Product Specification HI-SINCERITY Spec. No. : IC200409 Issued Date : 2004.05.01 Revised Date : 2004.05.14 Page No. : 3/7 MICROELECTRONICS CORP. Characteristics Curve Power Supply Current & Power Supply Voltage Large Signal Frequency Response 14 1.5 V OR, Output Voltage Range (Vpp)... ICC, Power Supply Current (mA)... 1.8 o Ta=25 C RL = 1.2 0.9 0.6 0.3 0 0 5 10 15 20 25 30 12 10 8 RL=2K VCC=15V VEE=GND AV=-100 RI=1K RF=100K 6 4 2 0 35 1 VCC, Power Supply Voltage (V) 10 1000 Voltage Follower Pulse Response Large Signal Open Loop Voltage Gain 1 8 Output Voltage (V) .. 120 100 VCC=15V VEE=Gnd o Ta=25 C 80 60 RL 2.0K V+=15VDC 3 7 2 6 1 5 0 4 Input Voltage (V).. AVOI, Open Loop Voltage Gain (dB)... 100 f, Frequency (KHz) 40 20 0 3 2 1 0 1 10 100 1000 10000 100000 1000000 0 f, Frequency (Hz) 5 10 15 20 25 30 35 40 t, Time (us) Small Signal Voltage Follower Pulse Response (Non Inverting) Voltage Gain 140 450 RL=20K AVOL, Voltage Gain (dB)... VO, Output Voltage (mV) 120 400 350 300 VCC=30V VEE=Gnd o Ta=25 C CL=50pF 250 100 RL=2K 80 60 40 20 0 200 0 1 2 3 4 t, Time (us) HLM358P, HLM358S 5 6 7 8 0 5 10 15 20 25 30 35 V+, Supply Voltage (V) HSMC Product Specification HI-SINCERITY Spec. No. : IC200409 Issued Date : 2004.05.01 Revised Date : 2004.05.14 Page No. : 4/7 MICROELECTRONICS CORP. Characteristics Curve Power Supply Voltage & Input Bias Current Input Voltage Range 15 50 o 45 Ta=25 C VIN, Input Voltage (V)... Input Bias Current (nA)... 40 35 30 25 20 15 Negative 10 Positive 5 10 5 0 0 0 5 10 15 20 25 30 35 0 5 Power Supply Voltage (V) 10 15 V+/V-, Power Supply Voltage (V) Typical Application Circuit Voltage Follower Non Inverting DC Amplifier + VIN 1/2 HLM358 1/2 HLM358 - VO OUT VO OUT R2 1M VIN + R 1 10K AV=1+R1/R2 DC Summing Amplifier V1 Squarewave Oscillator 100K + V2 V3 100K 100K 100K - 1/2 HLM358 OUT 0.001uF VO R 1 100K 1/2 HLM358 - + + 100K V4 - VIN 100K VO OUT R2 100K R 1 100K R4 100K VO=V1+V2-V3-V4 Where (V1+V2)(V3+V4) To keep VO0V HLM358P, HLM358S HSMC Product Specification HI-SINCERITY Spec. No. : IC200409 Issued Date : 2004.05.01 Revised Date : 2004.05.14 Page No. : 5/7 MICROELECTRONICS CORP. Typical Application Circuit Function Generator Vref=1/2VCC R Triangle Wave Output + Vref Pulse Generator 1 100K R 1/2 HLM358 3 100K - R1 C R 2 300K + OUT OUT 1/2 HLM358 C 150K 0.001uF Square Wave Output - VO OUT + 100K Vref Rf R2 1/2 HLM358 100K 1N914 + - V+ R 3 100K R 4 100K R5 100K F=(R1+RC)/4CRfR1 if R3=R2*R1/(R2+R1) DC Coupled Low-Pass RC Active Filter R VIN R2 1 16K 16K C 0.01uF R 1 0.01uF + 1/2 HLM358 C2 High Input Z, DC Differential Amplifier 1 100K - VO OUT R 1/2 HLM358 R3 - R 2 100K V1+ 100K 3 100K - OUT R 4 100K 1/2 HLM358 + OUT VO + V2+ R4 100K R1/R2=R4/R3 VO=1+R4/R3(V2-V1) As shown VO=2(V2-V1) f0=1KHz, Q=1, AV=2 Active Band-Pass Filter R 1 100K - 1/2 HLM358 R V1+ 2 100K C 1 330pF OUT + R - R 4 10M OUT R 3 100K C - 2 330pF OUT R7 1K 5 470K 1/2 HLM358 + R 6 470K VO 1/2 HLM358 R 7 100K + R8 C3 100K 10uF VCC f0=1KHz, Q=50, AV=100 (40dB) HLM358P, HLM358S HSMC Product Specification HI-SINCERITY Spec. No. : IC200409 Issued Date : 2004.05.01 Revised Date : 2004.05.14 Page No. : 6/7 MICROELECTRONICS CORP. DIP-8 Dimension DIM Min. Max. A 6.29 6.40 B 9.22 9.32 C - *1.52 D - *1.27 E - *0.99 Note: Green label is used for pb-free packing F 3.25 3.35 Pin Style: 1.Output 1 2.Inverting input 1 3.Non inverting input 1 4.VEE 5.Non inverting input 2 6.Inverting input 2 7. Output 2 8.VCC G 3.17 3.55 H 0.38 0.53 I 2.28 2.79 J 7.49 7.74 K - *3.00 Marking: 8 6 7 5 Pb Free Mark Pb-Free: " . " Normal: None (Note) A 1 2 3 H L M3 5 8 P 4 Control Code Date Code B J F E C M H D I Material: * Lead solder plating: Sn60/Pb40 (Normal), Sn/3.0Ag/0.5Cu or Pure-Tin (Pb-free) * Mold Compound: Epoxy resin family, flammability solid burning class: UL94V-0 1 K G L 8.56 8.81 M 0.229 94o 0.381 97o 1 L *: Typical, Unit: mm 8-Lead DIP-8 Plastic Package HSMC Package Code: P SO-8 Dimension A Marking: G Pb Free Mark 8 7 B 6 5 C Pin1 Index 2 3 Pb-Free: " . " (Note) H Normal: None I Pin 1 Index Date Code H Pin Style: 1.Output 1 2.Inverting input 1 3.Non inverting input 1 4.VEE 5.Non inverting input 2 6.Inverting input 2 7. Output 2 8.VCC K E Part A Part A Control Code Note: Green label is used for pb-free packing 4 J D S L M3 5 8 M L N O Material: * Lead solder plating: Sn60/Pb40 (Normal), Sn/3.0Ag/0.5Cu or Pure-Tin (Pb-free) * Mold Compound: Epoxy resin family, flammability solid burning class: UL94V-0 DIM A B C D E F G H I J K L M N O Min. 4.85 3.85 5.80 1.22 0.37 3.74 1.45 4.80 0.05 0.30 0.19 0.37 0.23 0.08 0.00 Max. 5.10 3.95 6.20 1.32 0.47 3.88 1.65 5.10 0.20 0.70 0.25 0.52 0.28 0.13 0.15 *: Typical, Unit: mm F 8-Lead SO-8 Plastic Surface Mounted Package HSMC Package Code: S Important Notice: * All rights are reserved. Reproduction in whole or in part is prohibited without the prior written approval of HSMC. * HSMC reserves the right to make changes to its products without notice. * HSMC semiconductor products are not warranted to be suitable for use in Life-Support Applications, or systems. * HSMC assumes no liability for any consequence of customer product design, infringement of patents, or application assistance. Head Office And Factory: * Head Office (Hi-Sincerity Microelectronics Corp.): 10F.,No. 61, Sec. 2, Chung-Shan N. Rd. Taipei Taiwan R.O.C. Tel: 886-2-25212056 Fax: 886-2-25632712, 25368454 * Factory 1: No. 38, Kuang Fu S. Rd., Fu-Kou Hsin-Chu Industrial Park Hsin-Chu Taiwan. R.O.C Tel: 886-3-5983621~5 Fax: 886-3-5982931 HLM358P, HLM358S HSMC Product Specification HI-SINCERITY Spec. No. : IC200409 Issued Date : 2004.05.01 Revised Date : 2004.05.14 Page No. : 7/7 MICROELECTRONICS CORP. Soldering Methods for HSMC's Products 1. Storage environment: Temperature=10oC~35oC Humidity=65%15% 2. Reflow soldering of surface-mount devices Figure 1: Temperature profile tP Critical Zone TL to TP TP Ramp-up TL tL Temperature Tsmax Tsmin tS Preheat Ramp-down 25 t 25oC to Peak Time Profile Feature Sn-Pb Eutectic Assembly Pb-Free Assembly <3oC/sec <3oC/sec 100oC 150oC 60~120 sec 150oC 200oC 60~180 sec <3oC/sec <3oC/sec Time maintained above: - Temperature (TL) - Time (tL) 183oC 60~150 sec 217oC 60~150 sec Peak Temperature (TP) 240oC +0/-5oC 260oC +0/-5oC Time within 5oC of actual Peak Temperature (tP) 10~30 sec 20~40 sec Ramp-down Rate <6oC/sec <6oC/sec o <6 minutes <8 minutes Peak temperature Dipping time 245 C 5 C 5sec 1sec Average ramp-up rate (TL to TP) Preheat - Temperature Min (Tsmin) - Temperature Max (Tsmax) - Time (min to max) (ts) Tsmax to TL - Ramp-up Rate Time 25 C to Peak Temperature 3. Flow (wave) soldering (solder dipping) Products Pb devices. Pb-Free devices. HLM358P, HLM358S o o o o 260 C +0/-5 C 5sec 1sec HSMC Product Specification