SPEC NO. 05-08-5013 REV. L RH1013M, DUAL PRECISION OPERATIONAL AMPLIFIER REVISION RECORD DESCRIPTION REV 0 A B C D E DATE INITIAL RELEASE PARAGRAPH 3.8 NOW REFLECTS THE CORRECT FIGURES FOR BURN-IN CIRCUITS FOR EACH PERTINENT PACKAGE. DELETION OF PARAGRAPHS 3.12.1 AND 3.12.2, AND INCORPORATION OF PARAGRAPH 3.12.1 INTO PARAGRAPH 3.12, PAGE 4. CHANGED BURN-IN CIRCUIT FOR FLATPACK. BURN-IN CIRCUIT NOW REFLECTS A CIRCUIT THAT IS USED FOR BOTH STATIC AND DYNAMIC. REMAINING FIGURES WILL BE RENUMBERED. WILL NOT CHANGE. PARAGRAPH 4.5.2 MOVED FROM PAGE 5 TO PAGE 4. ENTIRE SPECIFICATION IS RENUMBERED. ENTIRE SPECIFICATION REV'D. * PAGE 2, ADDED PARAGRAPHS 3.2.1, 3.2.2, AND 3.2.3. * PAGE 2, PARAGRAPH 3.3.b: ADDED "(SEE PARAGRAPH 3.2)". * PAGE 3, ADDED PARAGRAPHS 3.8.1, 3.8.2, AND 3.8.3. * PAGE 4, PARAGRAPH 4.4.2, GROUP B INSPECTION WAS REDEFINED. * PAGE 5, PARAGRAPH 4.4.3, GROUP D INSPECTION WAS REDEFINED. PARAGRAPH 4.5.1, SOURCE INSPECTION WAS REDEFINED. * PAGES 6, 7, 8, FIGURES 1, 2, 3 CASE OUTLINES: ADDED ja AND jc . * PAGE 9, REDREW FIGURES 5 AND 6 TERMINAL CONNECTIONS. * UPDATED ENTIRE SPEC TO REVISION B. * PAGE 17, CHANGED VOS MIN DELTA LIMIT FROM -60 V to -200 V, AND CHANGED VOS MAX DELTA LIMIT FROM 60 V TO 200 V. * ADDED A SECOND PAGE FOR REVISION RECORD. UPDATED ENTIRE SPEC TO NEXT REVISION DUE TO THE ADDITIONAL PAGE. * PAGE 3, PARAGRAPH 3.2.3, CHANGED PACKAGE TYPE TO 10 LEAD FLATPACK GLASS SEAL. * PAGE 4, PARAGRAPH 3.8.3, CHANGED OPTION 3 TO FLATPACK GLASS SEAL, AND PARAGRAPH 3.10.3, CHANGED LEAD MATERIAL AND FINISH TO KOVAR WITH HOT SOLDER DIP ON ALL PACKAGE OPTIONS. * PAGE 5, AMENDED PARAGRAPHS 4.1 AND 4.1.1 TAKING EXCEPTION TO ANALYSIS OF CATASTROPHIC FAILURES. * PAGE 9, FIGURE 3, CHANGED PACKAGE TYPE TO FLATPACK GLASS SEAL. * PAGE 10, FIGURE 6, CHANGED PACKAGE TYPE TO FLATPACK GLASS SEAL. * PAGE 14, FIGURE 10, CHANGED PACKAGE TYPE TO FLATPACK GLASS SEAL. * PAGE 7,8,9, FIGURE 1,2,3, CHANGED JA AND JC. 06/12/96 09/05/96 11/25/97 12/18/97 03/20/98 09/28/99 REVISION RECORD AND DESCRIPTION CONTINUED ON NEXT PAGE. CAUTION: ELECTROSTATIC DISCHARGE SENSITIVE PART REVISION INDEX REVISION INDEX PAGE NO. REVISION PAGE NO. REVISION APPLICATION 1 L 18 L ORIG DSGN ENGR MFG CM QA PROG FUNCT 2 L 3 L 4 L 5 L 6 L 7 L 8 L 9 L 10 L 11 L 12 L 13 L 14 L 15 L 16 L 17 L LINEAR TECHNOLOGY CORPORATION MILPITAS, CALIFORNIA TITLE: MICROCIRCUIT, LINEAR, RH1013M, DUAL PRECISION SIZE OPERATIONAL AMPLIFIER CAGE CODE DRAWING NUMBER 64155 SIGNOFFS DATE 05-08-5013 REV L CONTRACT: FOR OFFICIAL USE ONLY LINEAR TECHNOLOGY CORPORATION PAGE 1 OF 18 SPEC NO. 05-08-5013 REV. L REV F G H RH1013M, DUAL PRECISION OPERATIONAL AMPLIFIER REVISION RECORD DESCRIPTION * PAGE 3, PARAGRAPHS 3.2.1, 3.2.2, 3.2.3 HAD FIGURES 1, 2, AND 3 REMOVED. * PAGE 4, PARAGRAPH 3.7, CHANGED VERBIAGE FROM "SPECIFIED IN TABLE III" TO "AND AS SPECIFIED IN TABLE III HEREIN", LINE 2. PARAGRAPH 3.9, ADDED "HEREIN" AFTER "TABLE II", LINE 2. * PAGE 5, PARAGRAPH 4.3, ADDED "HEREIN" AFTER "TABLE III", LINE 2. PARAGRAPH 4.4.1, ADDED "HEREIN" AFTER "TABLE III", LINE 2. * PAGE 6, PARAGRAPH 4.4.2.2, CHANGED VERBIAGE IN LINE 1 FROM "ALL FOOTNOTES OF TABLE 11A OF MIL-STD-883" TO "ALL FOOTNOTES PERTAINING TO TABLE IIA IN MIL-STD883". PARAGRAPH 4.4.3.2, CHANGED VERBIAGE IN LINE 1 FROM "ALL FOOTNOTES OF TABLE IV OF MIL-STD-883" TO "ALL FOOTNOTES PERTAINING TO TABLE IV IN MIL-STD883'. * PAGE 9, CHANGED THETA JA TO JA=170C/W AND THETA JC TO JC=40C/W FROM JA=225C/W AND JC=18C/W PER PACKAGE ENGINEER. * PAGE 3: PARAGRAPH 3.2.1 ADDED "OPTION 1", PARAGRAPH 3.2.2, ADDED "OPTION 2", PARAGRAPH 3.2.3, ADDED "OPTION 3". DATE 11/18/99 08/30/00 04/08/03 * PAGE 4: PARAGRAPH 3.6, TABLE IA CHANGED TO TABLE II. PARAGRAPH 3.7, TABLE III CHANGED TO TABLE IV. PARAGRAPH 3.9, TABLE II CHANGED TO TABLE III. PARAGRAPH 3.10.3, ADDED "DEVICE OPTIONS 1, 2, AND 3" TO LINE 1. PARAGRAPH 3.11.1 WAS CHANGED FROM "...dosage rate of approximately 20 Rads per second" TO "...dosage rate of less than or equal to 10 Rads per second". * PAGE 5: PARAGRAPHS 4.1 THROUGH 4.4.2.1 CHANGES WERE DONE TO CLARIFY GROUP SAMPLING. PARAGRAPH 4.4.3 CHANGE WAS DONE TO CLARIFY GROUP SAMPLING. * PAGE 6: PARAGRAPHS 4.6.2 THROUGH 4.6.4 WERE RE-WRITTEN. THESE DATA PROVIDED, AND DATA AVAILABLE. PARAGRAPH 4.6.10 NOTE, ADDED FURTHER EXPLANATION OF MINIMUM DELIVERED DATA. * PAGES 7 THROUGH 15, ALL FIGURE TITLES CHANGED TO HAVE DEVICE OPTIONS AND PACKAGE TYPES AT TOP OF PAGE, AND HAVE ALL FIGURES AT BOTTOM OF PAGE. * PAGE 8: LEAD SHOULDER DIAMETER MAX NOW 0.065 INCHES (WAS 0.068). * PAGE 9: CASE OUTLINE UPDATED TO MIL-STD-1835. * PAGE 10: MOVED FIGURES TO BETTER FIT THE PAGE. * PAGE 17: TABLE IA HAS BECOME TABLE II. * PAGE 18: TABLE II HAS BECOME TABLE III. TABLE III HAS BECOME TABLE IV. J * PAGE 9: CASE OUTLINE DRAWING CHANGED PIN 1 NOTCH MOVED TO INSIDE LEAD LOCATION. 5/19/03 K L * PAGE 4: CHANGED INITIAL RATE OF RADS TO 240 RADS/SEC. * PAGE 5, CHANGED IN BOTH PARAGRAPHS 4.2, 4.3 IN CONJUNCTION TO 3.3 CHANGED TO 3.4 AND PARAGRAPH 4.3 CHANGED 3.1.1 TO 3.1 AND 3.2.1 TO 3.1.1 PAGE 4, PARAGRAPH 3.10.3 CHANGED OPTION 2 & ADDED OPTION 3 AS ALLOY 42. PARAGRAPH 3.11.1 CHANGED VERBIAGE. 03/15/05 04/23/08 * LINEAR TECHNOLOGY CORPORATION PAGE 2 OF 18 SPEC NO. 05-08-5013 REV. L 1.0 SCOPE: 1.1 2.0 RH1013M, DUAL PRECISION OPERATIONAL AMPLIFIER This specification defines the performance and test requirements for a microcircuit processed to a space level manufacturing flow. APPLICABLE DOCUMENTS: 2.1 Government Specifications and Standards: the following documents listed in the Department of Defense Index of Specifications and Standards, of the issue in effect on the date of solicitation, form a part of this specification to the extent specified herein. SPECIFICATIONS: 2.2 3.0 MIL-PRF-38535 Integrated Circuits (Microcircuits) Manufacturing, General Specification for MIL-STD-883 Test Method and Procedures for Microcircuits MIL-STD-1835 Microcircuits Case Outlines Order of Precedence: In the event of a conflict between the documents referenced herein and the contents of this specification, the order of precedence shall be this specification, MIL-PRF-38535 and other referenced specifications. REQUIREMENTS: 3.1 General Description: This specification details the requirements for the RH1013M DUAL PRECISION OPERATIONAL AMPLIFIER, processed to space level manufacturing flow. 3.2 Part Number: 3.3 3.2.1 Option 1 - RH1013MH (TO5 Metal Can, 8 Leads) 3.2.2 Option 2 - RH1013MJ8 (Ceramic Dip, 8 Leads) 3.2.3 Option 3 - RH1013MW (Glass Sealed Flatpack, 10 Leads) Part Marking Includes: a. LTC Logo b. LTC Part Number (See Paragraph 3.2) c. Date Code d. Serial Number e. ESD Identifier per MIL-PRF-38535, Appendix A LINEAR TECHNOLOGY CORPORATION PAGE 3 OF 18 SPEC NO. 05-08-5013 REV. L 3.4 RH1013M, DUAL PRECISION OPERATIONAL AMPLIFIER The Absolute Maximum Ratings: Supply Voltage (Pin 8 to Pin 4) . . . . . . . . . . . . . . +22V Differential Input Voltage . . . . . . . . . . . . . . . . +30V Input Voltage . . . . . . . . . . . . Equal to Positive Supply Voltage . . . . . . . . . . . 5V Below Negative Supply Voltage . . . . . . . . . . INDEFINITE Output Short Circuit Duration 1/ . . . . . . . . . . -55C to +125C Operating Temperature Range . . . . . . . . . . -65C to +150C Storage Temperature Range . . . . . . . . . . . +300C Lead Temperature (Soldering, 10 sec) 1/ Parameter is guaranteed by design, characterization, or correlation to other tested parameters. 3.5 Electrostatic discharge sensitivity, ESDS, shall be Class 1. 3.6 Electrical Performance Characteristics: The electrical performance characteristics shall be as specified in Table I and Table II. 3.7 Electrical Test Requirements: Screening requirements shall be in accordance with 4.1 herein, MIL-STD-883, Method 5004, and as specified in Table IV herein. 3.8 Burn-In Requirement: 3.8.1 Option 1 (TO5): Static Burn-In, Figure 7; Dynamic Burn-In, Figure 8 3.8.2 Option 2 (Ceramic Dip): Static/Dynamic Burn-In, Figure 9 3.8.3 Option 3 (Glass Sealed Flatpack) : Static/Dynamic Burn-In, Figure 10 3.9 Delta Limit Requirement: Delta limit parameters are specified in Table III herein, are calculated after each burn-in, and the delta rejects are included in the PDA calculation. 3.10 Design, Construction, and Physical Dimensions: Detail design, construction, physical dimensions, and electrical requirements shall be specified herein. 3.10.1 Mechanical / Packaging Requirements: Case outlines and dimensions are in accordance with Figure 1, Figure 2, and Figure 3. 3.10.2 Terminal Connections: The terminal connections shall be as specified in Figure 4, Figure 5, and Figure 6. 3.10.3 Lead Material and Finish: The lead material and finish for Device Options 1, shall be Kovar and options 2, 3 are Alloy 42.The lead finishes shall be hot solder dip (Finish letter A) in accordance with MIL-PRF-38535. 3.11 Radiation Hardness Assurance (RHA): 3.11.1 The manufacturer shall perform a lot sample test as an internal process monitor for total dose radiation tolerance. The sample test is performed with MIL-STD-883 TM1019 Condition A as a guideline. LINEAR TECHNOLOGY CORPORATION PAGE 4 OF 18 SPEC NO. 05-08-5013 REV. L RH1013M, DUAL PRECISION OPERATIONAL AMPLIFIER 3.11.2 For guaranteed radiation performance to MIL-STD-883, Method 1019, total dose irradiation, the manufacturer will provide certified RAD testing and report through an independent test laboratory when required as a customer purchase order line item. 3.11.3 Total dose bias circuit is specified in Figure 11. 4.0 3.12 Wafer Lot Acceptance: Wafer lot acceptance shall be in accordance with MIL-PRF-38535, Appendix A, except for the following: Topside glassivation thickness shall be a minimum of 4KA. 3.13 Wafer Lot Acceptance Report: SEM is performed per MIL-STD-883, Method 2018 and copies of SEM photographs shall be supplied with the Wafer Lot Acceptance Report as part of a Space Data Pack when specified as a customer purchase order line item. VERIFICATION (QUALITY ASSURANCE PROVISIONS) 4.1 Quality Assurance Provisions: Quality Assurance provisions shall be in accordance with MIL-PRF-38535. Linear Technology is a QML certified company and all Rad Hard candidates are assembled on qualified Class S manufacturing lines. 4.2 Sampling and Inspection: Sampling and Inspection shall be in accordance with MIL-STD-883, Method 5005 with QML allowed and TRB approved deviations in conjunction with paragraphs 3.1.1, 3.2.1, and 3.4 of the test method. 4.3 Screening: Screening requirements shall be in accordance with MIL-STD-883, Method 5004 with QML allowed and TRB approved deviations in conjunction with paragraphs 3.1, 3.1.1, and 3.4 of the test method. Electrical testing shall be as specified in Table IV herein. 4.3.1 4.4 Analysis of catastrophic (open/short) failures from burn-in will be conducted only when a lot fails the burn-in or re-burn-in PDA requirements. Quality Conformance Inspection: Quality conformance inspection shall be in accordance with 4.2 and 4.3 herein and as follows: 4.4.1 Group A Inspection: Group A inspection shall be performed in accordance with 4.1 herein, per MIL-STD-883, Method 5005, and specified in Table IV herein. 4.4.2 Group B Inspection: When purchased, a full Group B is performed on an inspection lot. As a minimum, Subgroup B2 (Resistance to Solvents / Mark Permanency) and Subgroup B3 (Solderability) are performed prior to the first shipment from any inspection lot and Attributes provided when a Full Space Data Pack is ordered. Subgroup B5 (Operating Life) is performed on each wafer lot. This subgroup may or may not be from devices built in the same package style as the current inspection lot. Attributes and variables data for this subgroup will be provided upon request at no charge. 4.4.2.1 Group B, Subgroup 2c = 10% Group B, Subgroup 3 = 10% Group B, Subgroup 4 = 5% 4.4.2.2 Group B, Subgroup 5 = *5% (*per wafer or inspection lot whichever is the larger quantity) Group B, Subgroup 6 = 15% All footnotes pertaining to Table IIa in MIL-STD-883, Method 5005 apply. The quantity (accept number) of all other subgroups are per MIL-STD-883, Method 5005, Table IIa. LINEAR TECHNOLOGY CORPORATION PAGE 5 OF 18 SPEC NO. 05-08-5013 REV. L 4.4.3 4.5 4.6 RH1013M, DUAL PRECISION OPERATIONAL AMPLIFIER Group D Inspection: When purchased, a full Group D is performed on an inspection lot. As a minimum, periodic full Group D sampling is performed on each package family for each assembly location every 26 weeks. A generic Group D Summary is provided when a full Space Data Pack is ordered. 4.4.3.1 Group D, Subgroups 3, 4 and 5 = 15% each (Sample Size Series). 4.4.3.2 All footnotes pertaining to Table IV in MIL-STD-883, Method 5005 apply. The quantity (accept number) or sample number and accept number of all other subgroups are per MILSTD-883, Method 5005, Table IV. Source Inspection: 4.5.1 The manufacturer will coordinate Source Inspection at wafer lot acceptance and pre-seal internal visual. 4.5.2 The procuring activity has the right to perform source inspection at the supplier's facility prior to shipment for each lot of deliverables when specified as a customer purchase order line item. This may include wafer lot acceptance and final data review. Deliverable Data: Deliverable data that will ship with devices when a Space Data Pack is ordered: 4.6.1 Lot Serial Number Sheets identifying all devices accepted through final inspection by serial number. 4.6.2 100% attributes (completed lot specific traveler; includes Group A Summary) 4.6.3 Burn-In Variables Data and Deltas (if applicable) 4.6.4 Group B2, B3, and B5 Attributes (Variables data, if performed on lot shipping) 4.6.5 Generic Group D data (4.4.3 herein) 4.6.6 SEM photographs (3.13 herein) 4.6.7 Wafer Lot Acceptance Report (3.13 herein) 4.6.8 X-Ray Negatives and Radiographic Report 4.6.9 A copy of outside test laboratory radiation report if ordered 4.6.10 Certificate of Conformance certifying that the devices meet all the requirements of this specification and have successfully completed the mandatory tests and inspections herein. Note: Items 4.6.1 and 4.6.10 will be delivered as a minimum, with each shipment. This is noted on the Purchase Order Review Form as "No Charge Data". 5.0 Packaging Requirements: Packaging shall be in accordance with Appendix A of MIL-PRF-38535. All devices shall be packaged in conductive material or packaged in anti-static material with an external conductive field shielding barrier. LINEAR TECHNOLOGY CORPORATION PAGE 6 OF 18 SPEC NO. 05-08-5013 REV. L RH1013M, DUAL PRECISION OPERATIONAL AMPLIFIER DEVICE OPTION # 1 (H) TO5 / 8 LEADS CASE OUTLINE ja = +150C/W jc = +40C/W FIGURE 1 LINEAR TECHNOLOGY CORPORATION PAGE 7 OF 18 SPEC NO. 05-08-5013 REV. L RH1013M, DUAL PRECISION OPERATIONAL AMPLIFIER DEVICE OPTION # 2 (J8) CERAMIC DIP / 8 LEADS CASE OUTLINE 0.045 - 0.065 (1.14 - 1.65) FULL LEAD OPTION NOTE: 1. LEAD DIMENSIONS APPLY TO SOLDER DIP OR TIN PLATE LEADS. 2. 8 LEAD D MAX = .405 (10.287) ja = +110C/W jc = +30C/W FIGURE 2 LINEAR TECHNOLOGY CORPORATION PAGE 8 OF 18 SPEC NO. 05-08-5013 REV. L RH1013M, DUAL PRECISION OPERATIONAL AMPLIFIER DEVICE OPTION # 3 (W10) GLASS SEALED FLATPACK / 10LEADS CASE OUTLINE NOTE: 1. THIS DIMENSION ALLOWS FOR OFF-CENTER LID, MENISCUS AND GLASS OVER RUN. NOTE: 2. INCREASE DIMENSION BY 0.003 INCH WHEN LEAD FINISH IS APPLIED (SOLDER DIPPED). ja = +170C/W jc = +40C/W FIGURE 3 LINEAR TECHNOLOGY CORPORATION PAGE 9 OF 18 SPEC NO. 05-08-5013 REV. L RH1013M, DUAL PRECISION OPERATIONAL AMPLIFIER TERMINAL CONNECTIONS DEVICE OPTION #1, TO5 8 LEAD METAL CAN DEVICE OPTION #2, 8 LEAD CERAMIC DIP FIGURE 4 FIGURE 5 FIGURE 5 DEVICE OPTION #3, GLASS SEALED 10 LEAD FLATPACK FIGURE 6 LINEAR TECHNOLOGY CORPORATION PAGE 10 OF 18 SPEC NO. 05-08-5013 REV. L RH1013M, DUAL PRECISION OPERATIONAL AMPLIFIER STATIC BURN-IN CIRCUIT OPTION 1, TO5 METAL CAN / 8 LEADS FIGURE 7 LINEAR TECHNOLOGY CORPORATION PAGE 11 OF 18 SPEC NO. 05-08-5013 REV. L RH1013M, DUAL PRECISION OPERATIONAL AMPLIFIER DYNAMIC BURN-IN CIRCUIT OPTION 1, TO5 METAL CAN / 8 LEADS FIGURE 8 LINEAR TECHNOLOGY CORPORATION PAGE 12 OF 18 SPEC NO. 05-08-5013 REV. L RH1013M, DUAL PRECISION OPERATIONAL AMPLIFIER STATIC/DYNAMIC BURN-IN CIRCUIT OPTION 2, CERDIP / 8 LEADS FIGURE 9 LINEAR TECHNOLOGY CORPORATION PAGE 13 OF 18 SPEC NO. 05-08-5013 REV. L RH1013M, DUAL PRECISION OPERATIONAL AMPLIFIER STATIC/DYNAMIC BURN-IN CIRCUIT OPTION 3, FLATPACK GLASS SEAL FIGURE 10 LINEAR TECHNOLOGY CORPORATION PAGE 14 OF 18 SPEC NO. 05-08-5013 REV. L RH1013M, DUAL PRECISION OPERATIONAL AMPLIFIER TOTAL DOSE BIAS CIRCUIT FIGURE 11 LINEAR TECHNOLOGY CORPORATION PAGE 15 OF 18 SPEC NO. 05-08-5013 REV. L RH1013M, DUAL PRECISION OPERATIONAL AMPLIFIER TABLE I: ELECTRICAL CHARACTERISTICS (PRE-IRRADIATION) Note: Table I electrical characteristics notes are on the next page following Table II . LINEAR TECHNOLOGY CORPORATION PAGE 16 OF 18 SPEC NO. 05-08-5013 REV. L RH1013M, DUAL PRECISION OPERATIONAL AMPLIFIER TABLE II: ELECTRICAL CHARACTERISTICS (POST-IRRADIATION) NOTE LINEAR TECHNOLOGY CORPORATION PAGE 17 OF 18 SPEC NO. 05-08-5013 REV. L RH1013M, DUAL PRECISION OPERATIONAL AMPLIFIER TABLE III: POST BURN-IN ENDPOINTS AND DELTA LIMIT REQUIREMENTS TA = 25C, VS = +15V, VCM = 0V unless otherwise noted PARAMETER VOS +IB -IB ENDPOINT LIMIT MIN MAX -300 300 -30 0 -30 0 DELTA MIN -200 -3 -3 MAX 200 3 3 UNITS V nA nA TABLE IV: ELECTRICAL TEST REQUIREMENTS MIL-STD-883 TEST REQUIREMENTS FINAL ELECTRICAL TEST REQUIREMENTS (METHOD 5004) GROUP A TEST REQUIREMENTS (METHOD 5005) GROUP B AND D FOR CLASS S ENDPOINT ELECTRICAL PARAMETERS (METHOD 5005) SUBGROUP 1*, 2, 3, 4, 5, 6 1, 2, 3, 4, 5, 6 1, 2, 3 *PDA APPLIES TO SUBGROUP 1. PDA TEST NOTE: The PDA is specified as 5% based on failures from Group A, Subgroup 1, tests after cooldown as the final electrical test in accordance with method 5004 of MIL-STD-883. The verified failures of Group A, Subgroup 1 and delta rejects after burn-in divided by the total number of devices submitted for burn-in in that lot shall be used to determine the percent for the lot LINEAR TECHNOLOGY CORPORATION PAGE 18 OF 18