Features * Core * * * * * * * - ARM(R) Cortex(R)-M3 revision 2.0 running at up to 64 MHz - Memory Protection Unit (MPU) - Thumb(R)-2 instruction set Pin-to-pin compatible with AT91SAM7S legacy products (64-pin versions), SAM3S4/2/1 products Memories - 512 Kbytes Single Plane (SAM3S8) embedded Flash, 128-bit wide access, memory accelerator - 512 Kbytes Dual Plane (SAM3SD8) embedded Flash, 128-bit wide access, memory accelerator - 64 Kbytes embedded SRAM - 16 Kbytes ROM with embedded boot loader routines (UART, USB) and IAP routines - 8-bit Static Memory Controller (SMC): SRAM, PSRAM, NOR and NAND Flash support System - Embedded voltage regulator for single supply operation - Power-on-Reset (POR), Brown-out Detector (BOD) and Watchdog for safe operation - Quartz or ceramic resonator oscillators: 3 to 20 MHz main power with Failure Detection and optional low-power 32.768 kHz for RTC or device clock - RTC with Gregorian and Persian Calendar mode, waveform generation in lowpower modes - RTC clock calibration circuitry for 32.768 kHz crystal frequency compensation - High precision 8/12 MHz factory trimmed internal RC oscillator with 4 MHz default frequency for device startup. In-application trimming access for frequency adjustment - Slow Clock Internal RC oscillator as permanent low-power mode device clock - Two PLLs up to 130 MHz for device clock and for USB - Temperature Sensor - Up to 24 peripheral DMA (PDC) channels Low Power Modes - Sleep and Backup modes, down to 1 A in Backup mode - Ultra low-power RTC Peripherals - USB 2.0 Device: 12 Mbps, 2668 byte FIFO, up to 8 bidirectional Endpoints. On-Chip Transceiver - Up to 3 USARTs with ISO7816, IrDA(R), RS-485, SPI, Manchester and Modem Mode - Two 2-wire UARTs - Up to 2 Two Wire Interface (I2C compatible), 1 SPI, 1 Serial Synchronous Controller (I2S), 1 High Speed Multimedia Card Interface (SDIO/SD Card/MMC) - 6 Three-Channel 16-bit Timer/Counter with capture, waveform, compare and PWM mode. Quadrature Decoder Logic and 2-bit Gray Up/Down Counter for Stepper Motor - 4-channel 16-bit PWM with Complementary Output, Fault Input, 12-bit Dead Time Generator Counter for Motor Control - 32-bit Real-time Timer and RTC with calendar and alarm features - Up to 15-channel, 1Msps ADC with differential input mode and programmable gain stage and auto calibration - One 2-channel 12-bit 1Msps DAC - One Analog Comparator with flexible input selection, Selectable input hysteresis - 32-bit Cyclic Redundancy Check Calculation Unit (CRCCU) I/O - Up to 79 I/O lines with external interrupt capability (edge or level sensitivity), debouncing, glitch filtering and on-die Series Resistor Termination - Three 32-bit Parallel Input/Output Controllers, Peripheral DMA assisted Parallel Capture Mode Packages - 100-lead LQFP, 14 x 14 mm, pitch 0.5 mm/100-ball TFBGA, 9 x 9 mm, pitch 0.8 mm - 64-lead LQFP, 10 x 10 mm, pitch 0.5 mm/64-pad QFN 9x9 mm, pitch 0.5 mm AT91SAM ARM-based Flash MCU SAM3S8/SD8 Series Summary 11090BS-ATARM-22-Oct-13 1. Description The Atmel SAM3S8/SD8 series is a member of a family of Flash microcontrollers based on the high performance 32-bit ARM Cortex-M3 RISC processor. It operates at a maximum speed of 64 MHz and features up to 512 Kbytes of Flash (dual plane on SAM3SD8) and up to 64 Kbytes of SRAM. The peripheral set includes a Full Speed USB Device port with embedded transceiver, a High Speed MCI for SDIO/SD/MMC, an External Bus Interface featuring a Static Memory Controller providing connection to SRAM, PSRAM, NOR Flash, LCD Module and NAND Flash, 2(3)x USARTs, (3 on SAM3SD8C) 2x UARTs, 2x TWIs, 3x SPI, an I2S, as well as 1 PWM timer, 6x general-purpose 16-bit timers (with stepper motor and quadrature decoder logic support), an RTC, a 12-bit ADC, a 12-bit DAC and an analog comparator. The SAM3S8/SD8 series is ready for capacitive touch thanks to the QTouch(R) library, offering an easy way to implement buttons, wheels and sliders. The SAM3S8/SD8 device is a medium range general purpose microcontroller with the best ratio in terms of reduced power consumption, processing power and peripheral set. This enables the SAM3S8/SD8 to sustain a wide range of applications including consumer, industrial control, and PC peripherals. It operates from 1.62V to 3.6V and is available in 64- and 100-pin QFP, 64-pin QFN, and 100-pin BGA packages. The SAM3S8/SD8 series is the ideal migration path from the SAM7S series for applications that require more performance. The SAM3S8/SD8 series is pin-to-pin compatible with the SAM7S series. 1.1 Configuration Summary The SAM3S8/SD8 series devices differ in memory size, package and features. Table 1-1 summarizes the configurations of the device family. Table 1-1. Configuration Summary Feature SAM3S8B SAM3S8C SAM3SD8B SAM3SD8C Flash 512 Kbytes 512 Kbytes 512 Kbytes 512 Kbytes SRAM 64 Kbytes 64 Kbytes 64 Kbytes 64 Kbytes Package LQFP64 QFN64 LQFP100 BGA100 LQFP64 QFN64 LQFP100 BGA100 Number of PIOs 47 79 (2) 47 (2) 79 (2) 16 channels(2) 12-bit ADC 11 channels 16 channels 11 channels 12-bit DAC 2 channels 2 channels 2 channels 2 channels Timer Counter Channels 6 6 6 6 PDC Channels 22 22 24 24 USART/UART HSMCI (1) 1 port/4 bits - (1) 2/2 2/2 External Bus Interface Notes: (1) 1 port/4 bits 2/2 1 port/4 bits 8-bit data, 4 chip selects, 24-bit address - 3/2(1) 1 port/4 bits 8-bit data, 4 chip selects, 24-bit address 1. Full Modem support on USART1. 2. One channel is reserved for internal temperature sensor. 2 SAM3S8/SD8 Summary 11090BS-ATARM-22-Oct-13 SAM3S8/SD8 Summary 2. Block Diagram TST System Controller UT VD DO VD DI N JT AG SE L SAM3S8/SD8 100-pin version Block Diagram TD TDI TMO TC S/S K/ WD SW IO CL K Figure 2-1. Voltage Regulator PCK0-PCK2 PLLA PLLB PMC RC Osc 12/8/4 MHz XIN XOUT JTAG & Serial Wire In-Circuit Emulator 3-20 MHz Osc Cortex M-3 Processor Fmax 64 MHz SUPC 24-Bit N SysTick Counter V I C MPU XIN32 XOUT32 Osc 32 kHz ERASE RC 32 kHz VDDIO 8 GPBREG I/D Flash Unique Identifier 512 KBytes FLASH SRAM ROM SAM3S8 Single Bank 64 KBytes 16 KBytes SAM3SD8 Dual Bank S 3-layer AHB Bus Matrix Fmax 64 MHz VDDCORE RTT VDDPLL RTCOUT0 POR RSTC WDT Peripheral Bridge SM 2668 USB 2.0 Bytes Full FIFO Speed PIOA / PIOB / PIOC TWCK0 TWD0 TWCK1 TWD1 URXD0 UTXD0 URXD1 UTXD1 RXD0 TXD0 SCK0 RTS0 CTS0 RXD1 TXD1 SCK1 RTS1 CTS1 DSR1 DTR1 RI1 DCD1 RXD2 TXD2 SCK2 RTS2 CTS2 TWI0 PDC TWI1 PDC UART0 PDC UART1 DDP DDM External Bus Interface NAND Flash Logic PDC PIO NRST Transceiver RTC RTCOUT1 Static Memory Controller USART0 PDC PDC PIODC[7:0] PIODCEN1 PIODCEN2 PIODCCLK USART1 PIO PDC USART2 (SAM3SD8 Only) Timer Counter B TIOA[0:2] TIOB[0:2] TC[0..2] NPCS0 NPCS1 NPCS2 NPCS3 MISO MOSI SPCK TF TK TD RD RK RF PDC PDC TCLK[0:2] SPI PDC SSC TCLK[3:5] Timer Counter B TIOA[3:5] TIOB[3:5] PDC ADVREF DAC0 DAC1 DATRG MCCK MCCDA MCDA[0..3] TC[3..5] High Speed MCI PWMH[0:3] PWML[0:3] PWMFI0 ADTRG AD[0..14] D[7:0] A[0:23] A21/NANDALE A22/NANDCLE NCS0 NCS1 NCS2 NCS3 NRD NWE NANDOE NANDWE NWAIT PWM PDC Temp. Sensor 12-bit ADC Analog Comparator ADVREF ADC Ch. CRC Unit PDC 12-bit DAC PDC 3 11090BS-ATARM-22-Oct-13 TST System Controller DO VD DI N VD JT AG SE L UT SAM3S8/SD8 64-pin version Block Diagram TD TDI TMO TC S/S K/ W D SW IO CL K Figure 2-2. Voltage Regulator PCK0-PCK2 PLLA PLLB PMC RC Osc 12/8/4 MHz XIN XOUT JTAG & Serial Wire In-Circuit Emulator 3-20 MHz Osc Cortex M-3 Processor Fmax 64 MHz SUPC 24-Bit N SysTick Counter V I C MPU XIN32 XOUT32 Osc 32 kHz ERASE RC 32 kHz VDDIO 8 GPBREG I/D Flash Unique Identifier 512 KBytes FLASH SRAM ROM SAM3S8 Single Bank 64 KBytes 16 KBytes SAM3SD8 Dual Bank S 3-layer AHB Bus Matrix Fmax 64 MHz VDDCORE RTT VDDPLL RTCOUT0 POR RSTC NRST WDT Peripheral Bridge SM 2668 USB 2.0 Bytes Full FIFO Speed PIOA / PIOB TWCK0 TWD0 TWI0 TWCK1 TWD1 TWI1 URXD0 UTXD0 UART0 URXD1 UTXD1 UART1 RXD0 TXD0 SCK0 RTS0 CTS0 DDP DDM PDC PDC PDC PDC PIODC[7:0] PIODCEN1 PIODCEN2 PIODCCLK PIO PDC USART0 PDC PDC SPI PIO USART1 PIO RXD1 TXD1 SCK1 RTS1 CTS1 DSR1 DTR1 RI1 DCD1 Transceiver RTC RTCOUT1 PDC PDC TCLK[0:2] TIOA[0:2] TIOB[0:2] ADTRG AD[0..14] SSC TC[0..2] PDC PWM PDC 4 MCCK MCCDA MCDA[0..3] High Speed MCI Temp. Sensor 12-bit ADC ADVREF DAC0 DAC1 DATRG TF TK TD RD RK RF Timer Counter A PWMH[0:3] PWML[0:3] PWMFI0 NPCS0 NPCS1 NPCS2 NPCS3 MISO MOSI SPCK PDC Analog Comparator PDC CRC Unit 12-bit DAC ADVREF ADC Ch. SAM3S8/SD8 Summary 11090BS-ATARM-22-Oct-13 SAM3S8/SD8 Summary 3. Signal Description Table 3-1 gives details on signal names classified by peripheral. Table 3-1. Signal Description List Signal Name Function Type Active Level Voltage reference Comments Power Supplies VDDIO Peripherals I/O Lines and USB transceiver Power Supply Power 1.62V to 3.6V VDDIN Voltage Regulator Input, ADC, DAC and Analog Comparator Power Supply Power 1.8V to 3.6V(4) VDDOUT Voltage Regulator Output Power 1.8V Output VDDPLL Oscillator and PLL Power Supply Power 1.62 V to 1.95V VDDCORE Power the core, the embedded memories and the peripherals Power GND Ground Ground 1.62V to 1.95V Clocks, Oscillators and PLLs XIN Main Oscillator Input XOUT Main Oscillator Output XIN32 Slow Clock Oscillator Input XOUT32 Slow Clock Oscillator Output PCK0 - PCK2 Input Reset State: - PIO Input - Internal Pull-up disabled - Schmitt Trigger enabled(1) Output Input Output Programmable Clock Output VDDIO Reset State: - PIO Input - Internal Pull-up enabled - Schmitt Trigger enabled(1) Output Real Time Clock RTCOUT0 Programmable RTC waveform output Output RTCOUT1 Programmable RTC waveform output Output VDDIO Reset State: - PIO Input - Internal Pull-up disabled - Schmitt Trigger enabled(1) Serial Wire/JTAG Debug Port - SWJ-DP TCK/SWCLK Test Clock/Serial Wire Clock Input TDI Test Data In Input TDO/TRACESWO Test Data Out / Trace Asynchronous Data Out Output TMS/SWDIO Test Mode Select /Serial Wire Input/Output Input / I/O JTAGSEL JTAG Selection Input VDDIO High Reset State: - SWJ-DP Mode - Internal pull-up disabled(5) - Schmitt Trigger enabled(1) Permanent Internal pull-down 5 11090BS-ATARM-22-Oct-13 Table 3-1. Signal Description List (Continued) Signal Name Function Type Active Level Voltage reference Comments Flash Memory Flash and NVM Configuration Bits Erase Command ERASE Input High VDDIO Reset State: - Erase Input - Internal pull-down enabled - Schmitt Trigger enabled(1) Reset/Test NRST Synchronous Microcontroller Reset I/O Low VDDIO TST Test Select Permanent Internal pull-up Permanent Internal pull-down Input Universal Asynchronous Receiver Transceiver - UARTx URXDx UART Receive Data Input UTXDx UART Transmit Data Output PIO Controller - PIOA - PIOB - PIOC PA0 - PA31 Parallel IO Controller A I/O PB0 - PB14 Parallel IO Controller B I/O PC0 - PC31 Parallel IO Controller C I/O VDDIO Reset State: - PIO or System IOs(2) - Internal pull-up enabled - Schmitt Trigger enabled(1) PIO Controller - Parallel Capture Mode PIODC0-PIODC7 Parallel Capture Mode Data Input PIODCCLK Parallel Capture Mode Clock Input PIODCEN1-2 Parallel Capture Mode Enable Input VDDIO External Bus Interface D0 - D7 Data Bus I/O A0 - A23 Address Bus NWAIT External Wait Signal Output Input Low Static Memory Controller - SMC NCS0 - NCS3 Chip Select Lines Output Low NRD Read Signal Output Low NWE Write Enable Output Low NAND Flash Logic NANDOE NAND Flash Output Enable Output Low NANDWE NAND Flash Write Enable Output Low High Speed Multimedia Card Interface - HSMCI MCCK Multimedia Card Clock I/O MCCDA Multimedia Card Slot A Command I/O MCDA0 - MCDA3 Multimedia Card Slot A Data I/O 6 SAM3S8/SD8 Summary 11090BS-ATARM-22-Oct-13 SAM3S8/SD8 Summary Table 3-1. Signal Description List (Continued) Signal Name Function Type Active Level Voltage reference Comments Universal Synchronous Asynchronous Receiver Transmitter USARTx SCKx USARTx Serial Clock I/O TXDx USARTx Transmit Data I/O RXDx USARTx Receive Data Input RTSx USARTx Request To Send CTSx USARTx Clear To Send DTR1 USART1 Data Terminal Ready DSR1 USART1 Data Set Ready DCD1 USART1 Data Carrier Detect RI1 USART1 Ring Indicator Output Input I/O Input Output Input Synchronous Serial Controller - SSC TD SSC Transmit Data Output RD SSC Receive Data Input TK SSC Transmit Clock I/O RK SSC Receive Clock I/O TF SSC Transmit Frame Sync I/O RF SSC Receive Frame Sync I/O Timer/Counter - TC TCLKx TC Channel x External Clock Input Input TIOAx TC Channel x I/O Line A I/O TIOBx TC Channel x I/O Line B I/O Pulse Width Modulation Controller- PWMC PWMHx PWM Waveform Output High for channel x PWMLx PWM Waveform Output Low for channel x PWMFI0 PWM Fault Input Output only output in complementary mode when dead time insertion is enabled. Output Input Serial Peripheral Interface - SPI MISO Master In Slave Out I/O MOSI Master Out Slave In I/O SPCK SPI Serial Clock I/O SPI_NPCS0 SPI Peripheral Chip Select 0 I/O Low SPI_NPCS1 SPI_NPCS3 SPI Peripheral Chip Select Output Low 7 11090BS-ATARM-22-Oct-13 Table 3-1. Signal Description List (Continued) Signal Name Function Type Active Level Voltage reference Comments Two-Wire Interface- TWI TWDx TWIx Two-wire Serial Data I/O TWCKx TWIx Two-wire Serial Clock I/O Analog ADC, DAC and Analog Comparator Reference ADVREF Analog 12-bit Analog-to-Digital Converter - ADC AD0-AD14 Analog Inputs Analog, Digital ADTRG ADC Trigger Input VDDIO 12-bit Digital-to-Analog Converter - DAC DAC0 - DAC1 Analog output DACTRG DAC Trigger Analog, Digital Input VDDIO Fast Flash Programming Interface - FFPI PGMEN0PGMEN2 Programming Enabling Input PGMM0-PGMM3 Programming Mode Input PGMD0-PGMD15 Programming Data I/O PGMRDY Programming Ready Output High PGMNVALID Data Direction Output Low PGMNOE Programming Read Input Low PGMCK Programming Clock Input PGMNCMD Programming Command Input VDDIO VDDIO Low USB Full Speed Device DDM DDP Note: USB Full Speed Data USB Full Speed Data + Analog, Digital VDDIO Reset State: - USB Mode - Internal Pull-down(3) 1. Schmitt Triggers can be disabled through PIO registers. 2. Some PIO lines are shared with System I/Os. 3. Refer to USB Section of the product Electrical Characteristics for information on Pull-down value in USB Mode. 4. See "Typical Powering Schematics" Section for restrictions on voltage range of Analog Cells. 5. TDO pin is set in input mode when the Cortex-M3 Core is not in debug mode. Thus the internal pull-up corresponding to this PIO line must be enabled to avoid current consumption due to floating input. 8 SAM3S8/SD8 Summary 11090BS-ATARM-22-Oct-13 SAM3S8/SD8 Summary 4. Package and Pinout SAM3S8/SD8 devices are pin-to-pin compatible with AT91SAM7S legacy products for 64-pin version. Furthermore, SAM3S8/SD8 products have new functionalities referenced in italic in Table 4-1, Table 4-3. 4.1 4.1.1 SAM3S8C/8DC Package and Pinout 100-Lead LQFP Package Outline Figure 4-1. Orientation of the 100-lead LQFP Package 75 51 76 50 100 26 1 4.1.2 25 100-ball TFBGA Package Outline The 100-Ball TFBGA package has a 0.8 mm ball pitch and respects Green Standards. Its dimensions are 9 x 9 x 1.1 mm. Figure 4-2 shows the orientation of the 100-ball TFBGA Package. Figure 4-2. Orientation of the 100-ball TFBGA Package TOP VIEW 10 9 8 7 6 5 4 3 2 1 BALL A1 A B C D E F G H J K 9 11090BS-ATARM-22-Oct-13 4.1.3 100-Lead LQFP Pinout Table 4-1. SAM3S8C/SD8C 100-lead LQFP pinout 1 ADVREF 26 GND 51 TDI/PB4 76 TDO/TRACESWO/ PB5 2 GND 27 VDDIO 52 PA6/PGMNOE 77 JTAGSEL 3 PB0/AD4 28 PA16/PGMD4 53 PA5/PGMRDY 78 PC18 4 PC29/AD13 29 PC7 54 PC28 79 TMS/SWDIO/PB6 5 PB1/AD5 30 PA15/PGMD3 55 PA4/PGMNCMD 80 PC19 6 PC30/AD14 31 PA14/PGMD2 56 VDDCORE 81 PA31 7 PB2/AD6 32 PC6 57 PA27/PGMD15 82 PC20 8 PC31 33 PA13/PGMD1 58 PC8 83 TCK/SWCLK/PB7 9 PB3/AD7 34 PA24/PGMD12 59 PA28 84 PC21 10 VDDIN 35 PC5 60 NRST 85 VDDCORE 11 VDDOUT 36 VDDCORE 61 TST 86 PC22 12 PA17/PGMD5/AD0 37 PC4 62 PC9 87 ERASE/PB12 13 PC26 38 PA25/PGMD13 63 PA29 88 DDM/PB10 14 PA18/PGMD6/AD1 39 PA26/PGMD14 64 PA30 89 DDP/PB11 15 PA21/PGMD9/AD8 40 PC3 65 PC10 90 PC23 16 VDDCORE 41 PA12/PGMD0 66 PA3 91 VDDIO 17 PC27 42 PA11/PGMM3 67 PA2/PGMEN2 92 PC24 18 PA19/PGMD7/AD2 43 PC2 68 PC11 93 PB13/DAC0 19 PC15/AD11 44 PA10/PGMM2 69 VDDIO 94 PC25 20 PA22/PGMD10/AD 9 45 GND 70 GND 95 GND 21 PC13/AD10 46 PA9/PGMM1 71 PC14 96 PB8/XOUT 22 PA23/PGMD11 47 PC1 72 PA1/PGMEN1 97 PB9/PGMCK/XIN 23 PC12/AD12 48 PA8/XOUT32/ PGMM0 73 PC16 98 VDDIO 24 PA20/PGMD8/AD3 49 PA7/XIN32/ PGMNVALID 74 PA0/PGMEN0 99 PB14/DAC1 25 PC0 50 VDDIO 75 PC17 100 VDDPLL 10 SAM3S8/SD8 Summary 11090BS-ATARM-22-Oct-13 SAM3S8/SD8 Summary 4.1.4 100-Ball TFBGA Pinout Table 4-2. SAM3S8C/SD8C 100-ball TFBGA pinout A1 PB1/AD5 C6 TCK/SWCLK/PB7 F1 PA18/PGMD6/AD1 H6 PC4 A2 PC29 C7 PC16 F2 PC26 H7 PA11/PGMM3 A3 VDDIO C8 PA1/PGMEN1 F3 VDDOUT H8 PC1 A4 PB9/PGMCK/XIN C9 PC17 F4 GND H9 PA6/PGMNOE A5 PB8/XOUT C10 PA0/PGMEN0 F5 VDDIO H10 TDI/PB4 A6 PB13/DAC0 D1 PB3/AD7 F6 PA27/PGMD15 J1 PC15/AD11 A7 DDP/PB11 D2 PB0/AD4 F7 PC8 J2 PC0 A8 DDM/PB10 D3 PC24 F8 PA28 J3 PA16/PGMD4 A9 TMS/SWDIO/PB6 D4 PC22 F9 TST J4 PC6 A10 JTAGSEL D5 GND F10 PC9 J5 PA24/PGMD12 B1 PC30 D6 GND G1 PA21/PGMD9/AD8 J6 PA25/PGMD13 B2 ADVREF D7 VDDCORE G2 PC27 J7 PA10/PGMM2 B3 GNDANA D8 PA2/PGMEN2 G3 PA15/PGMD3 J8 GND B4 PB14/DAC1 D9 PC11 G4 VDDCORE J9 VDDCORE B5 PC21 D10 PC14 G5 VDDCORE J10 VDDIO B6 PC20 E1 PA17/PGMD5/AD 0 G6 PA26/PGMD14 K1 PA22/PGMD10/AD 9 B7 PA31 E2 PC31 G7 PA12/PGMD0 K2 PC13/AD10 B8 PC19 E3 VDDIN G8 PC28 K3 PC12/AD12 B9 PC18 E4 GND G9 PA4/PGMNCMD K4 PA20/PGMD8/AD3 B10 TDO/TRACESWO/ PB5 E5 GND G10 PA5/PGMRDY K5 PC5 C1 PB2/AD6 E6 NRST H1 PA19/PGMD7/AD2 K6 PC3 C2 VDDPLL E7 PA29/AD13 H2 PA23/PGMD11 K7 PC2 C3 PC25 E8 PA30/AD14 H3 PC7 K8 PA9/PGMM1 C4 PC23 E9 PC10 H4 PA14/PGMD2 K9 PA8/XOUT32/PGM M0 C5 ERASE/PB12 E10 PA3 H5 PA13/PGMD1 K10 PA7/XIN32/ PGMNVALID 11 11090BS-ATARM-22-Oct-13 4.2 4.2.1 SAM3S8B/D8B Package and Pinout 64-Lead LQFP Package Outline Figure 4-3. Orientation of the 64-lead LQFP Package 33 48 49 32 64 17 16 1 4.2.2 64-lead QFN Package Outline Figure 4-4. Orientation of the 64-lead QFN Package 64 1 48 16 33 17 12 49 TOP VIEW 32 SAM3S8/SD8 Summary 11090BS-ATARM-22-Oct-13 SAM3S8/SD8 Summary 4.2.3 64-Lead LQFP and QFN Pinout Table 4-3. 64-pin SAM3S8B/D8B pinout 1 ADVREF 17 GND 33 TDI/PB4 49 TDO/TRACESWO/ PB5 2 GND 18 VDDIO 34 PA6/PGMNOE 50 JTAGSEL 3 PB0/AD4 19 PA16/PGMD4 35 PA5/PGMRDY 51 TMS/SWDIO/PB6 4 PB1/AD5 20 PA15/PGMD3 36 PA4/PGMNCMD 52 PA31 5 PB2/AD6 21 PA14/PGMD2 37 PA27/PGMD15 53 TCK/SWCLK/PB7 6 PB3/AD7 22 PA13/PGMD1 38 PA28 54 VDDCORE 7 VDDIN 23 PA24/PGMD12 39 NRST 55 ERASE/PB12 8 VDDOUT 24 VDDCORE 40 TST 56 DDM/PB10 9 PA17/PGMD5/ AD0 25 PA25/PGMD13 41 PA29 57 DDP/PB11 10 PA18/PGMD6/ AD1 26 PA26/PGMD14 42 PA30 58 VDDIO 11 PA21/PGMD9/ AD8 27 PA12/PGMD0 43 PA3 59 PB13/DAC0 12 VDDCORE 28 PA11/PGMM3 44 PA2/PGMEN2 60 GND 13 PA19/PGMD7/ AD2 29 PA10/PGMM2 45 VDDIO 61 XOUT/PB8 14 PA22/PGMD10/ AD9 30 PA9/PGMM1 46 GND 62 XIN/PGMCK/PB9 15 PA23/PGMD11 31 PA8/XOUT32/ PGMM0 47 PA1/PGMEN1 63 PB14/DAC1 16 PA20/PGMD8/ AD3 32 PA7/XIN32/ PGMNVALID 48 PA0/PGMEN0 64 VDDPLL Note: The bottom pad of the QFN package must be connected to ground. 13 11090BS-ATARM-22-Oct-13 5. Power Considerations 5.1 Power Supplies The SAM3S8/SD8 has several types of power supply pins: * VDDCORE pins: Power the core, the embedded memories and the peripherals. Voltage ranges from 1.62V to 1.95V. * VDDIO pins: Power the Peripherals I/O lines (Input/Output Buffers), USB transceiver, Backup part, 32 kHz crystal oscillator and oscillator pads. Voltage ranges from 1.62V to 3.6V. * VDDIN pin: Voltage Regulator Input, ADC, DAC and Analog Comparator Power Supply. Voltage ranges from 1.8V to 3.6V. * VDDPLL pin: Powers the PLLA, PLLB, the Fast RC and the 3 to 20 MHz oscillator. Voltage ranges from 1.62V to 1.95V. 5.2 Voltage Regulator The SAM3S8/SD8 embeds a voltage regulator that is managed by the Supply Controller. This internal regulator is designed to supply the internal core of SAM3S8/SD8. It features two operating modes: * In Normal mode, the voltage regulator consumes less than 700 A static current and draws 80 mA of output current. Internal adaptive biasing adjusts the regulator quiescent current depending on the required load current. In Wait Mode quiescent current is only 7 A. * In Backup mode, the voltage regulator consumes less than 1 A while its output (VDDOUT) is driven internally to GND. The default output voltage is 1.80V and the start-up time to reach Normal mode is less than 100 s. For adequate input and output power supply decoupling/bypassing, refer to the "Voltage Regulator" section in the "Electrical Characteristics" section of the datasheet. 5.3 Typical Powering Schematics The SAM3S8/SD8 supports a 1.62V-3.6V single supply mode. The internal regulator input connected to the source and its output feeds VDDCORE. Figure 5-1 below shows the power schematics. As VDDIN powers the voltage regulator, the ADC, DAC and the analog comparator, when the user does not want to use the embedded voltage regulator, it can be disabled by software via the SUPC (note that this is different from Backup mode). 14 SAM3S8/SD8 Summary 11090BS-ATARM-22-Oct-13 SAM3S8/SD8 Summary Figure 5-1. Single Supply VDDIO Main Supply (1.8V-3.6V) USB Transceivers. ADC, DAC Analog Comp. VDDIN VDDOUT Voltage Regulator VDDCORE VDDPLL Note: Restrictions With Main Supply < 2.0 V, USB and ADC/DAC and Analog comparator are not usable. With Main Supply 2.0V and < 3V, USB is not usable. With Main Supply 3V, all peripherals are usable. Figure 5-2. Core Externally Supplied VDDIO Main Supply (1.62V-3.6V) USB Transceivers. Can be the same supply ADC, DAC, Analog Comparator Supply (2.0V-3.6V) ADC, DAC Analog Comp. VDDIN VDDOUT VDDCORE Supply (1.62V-1.95V) Voltage Regulator VDDCORE VDDPLL Note: Restrictions With Main Supply < 2.0V, USB is not usable. With VDDIN < 2.0V, ADC, DAC and Analog comparator are not usable. With Main Supply 2.0V and < 3V, USB is not usable. With Main Supply and VDDIN 3V, all peripherals are usable. Figure 5-3 below provides an example of the powering scheme when using a backup battery. Since the PIO state is preserved when in backup mode, any free PIO line can be used to switch off the external regulator by driving the PIO line at low level (PIO is input, pull-up enabled after backup reset). External wake-up of the system can be from a push button or any signal. See Section 5.6 "Wake-up Sources" for further details. 15 11090BS-ATARM-22-Oct-13 Figure 5-3. Backup Battery ADC, DAC, Analog Comparator Supply (2.0V-3.6V) Backup Battery VDDIO USB Transceivers. + ADC, DAC Analog Comp. VDDIN Main Supply IN OUT 3.3V LDO VDDOUT Voltage Regulator VDDCORE ON/OFF VDDPLL PIOx (Output) WAKEUPx External wakeup signal Note: The two diodes provide a "switchover circuit" (for illustration purpose) between the backup battery and the main supply when the system is put in backup mode. 5.4 Active Mode Active mode is the normal running mode with the core clock running from the fast RC oscillator, the main crystal oscillator or the PLLA. The power management controller can be used to adapt the frequency and to disable the peripheral clocks. 5.5 Low-power Modes The various low-power modes of the SAM3S8/SD8 are described below: 5.5.1 Backup Mode The purpose of backup mode is to achieve the lowest power consumption possible in a system which is performing periodic wake-ups to perform tasks but not requiring fast startup time (<0.1ms). Total current consumption is 1.5 A typical. The Supply Controller, zero-power power-on reset, RTT, RTC, Backup registers and 32 kHz oscillator (RC or crystal oscillator selected by software in the Supply Controller) are running. The regulator and the core supply are off. Backup mode is based on the Cortex-M3 deep sleep mode with the voltage regulator disabled. The SAM3S8/SD8 can be awakened from this mode through WUP0-15 pins, the supply monitor (SM), the RTT or RTC wake-up event. Backup mode is entered by using WFE instructions with the SLEEPDEEP bit in the Cortex-M3 System Control Register set to 1. (See the Power management description in The ARM CortexM3 Processor section of the product datasheet). Exit from Backup mode happens if one of the following enable wake up events occurs: * WKUPEN0-15 pins (level transition, configurable debouncing) 16 SAM3S8/SD8 Summary 11090BS-ATARM-22-Oct-13 SAM3S8/SD8 Summary * Supply Monitor alarm * RTC alarm * RTT alarm 5.5.2 Wait Mode The purpose of the wait mode is to achieve very low power consumption while maintaining the whole device in a powered state for a startup time of less than 10 s. Current Consumption in Wait mode is typically 15 A (total current consumption) if the internal voltage regulator is used or 8 A if an external regulator is used. In this mode, the clocks of the core, peripherals and memories are stopped. However, the core, peripherals and memories power supplies are still powered. From this mode, a fast start up is available. This mode is entered via Wait for Event (WFE) instructions with LPM = 1 (Low Power Mode bit in PMC_FSMR). The Cortex-M3 is able to handle external events or internal events in order to wake-up the core (WFE). This is done by configuring the external lines WUP0-15 as fast startup wake-up pins (refer to Section 5.7 "Fast Startup"). RTC or RTT Alarm and USB wake-up events can be used to wake up the CPU (exit from WFE). Entering Wait Mode: * Select the 4/8/12 MHz fast RC oscillator as Main Clock * Set the LPM bit in the PMC Fast Startup Mode Register (PMC_FSMR) * Execute the Wait-For-Event (WFE) instruction of the processor Note: 5.5.3 Internal Main clock resynchronization cycles are necessary between the writing of MOSCRCEN bit and the effective entry in Wait mode. Depending on the user application, waiting for MOSCRCEN bit to be cleared is recommended to ensure that the core will not execute undesired instructions. Sleep Mode The purpose of sleep mode is to optimize power consumption of the device versus response time. In this mode, only the core clock is stopped. The peripheral clocks can be enabled. The current consumption in this mode is application dependent. This mode is entered via Wait for Interrupt (WFI) or Wait for Event (WFE) instructions with LPM = 0 in PMC_FSMR. The processor can be awakened from an interrupt if WFI instruction of the Cortex M3 is used, or from an event if the WFE instruction is used to enter this mode. 17 11090BS-ATARM-22-Oct-13 5.5.4 Low Power Mode Summary Table The modes detailed above are the main low-power modes. Each part can be set to on or off separately and wake up sources can be individually configured. Table 5-1 below shows a summary of the configurations of the low-power modes. Table 5-1. Mode Backup Mode Wait Mode Sleep Mode Notes: Low-power Mode Configuration Summary SUPC, 32 kHz Oscillator, RTC, RTT Backup Registers, Core POR Memory (Backup Region) Regulator Peripherals ON ON ON Mode Entry PIO State Potential Wake Up Core at while in Low PIO State Consumption Wake-up (2) (3) Sources Wake Up Power Mode at Wake Up Time(1) Previous state saved PIOA & PIOB & PIOC Inputs with pull ups ON WFE Powered +SLEEPDEEP bit = 0 (Not clocked) +LPM bit = 1 Any Event from: Fast startup through WUP0-15 pins Clocked RTC alarm back RTT alarm USB wake-up Previous state saved Unchanged 5 A/15 A (5) < 10 s ON Entry mode =WFI Interrupt Only; Entry mode =WFE Any WFE or WFI Enabled Interrupt Powered(7) +SLEEPDEEP and/or Any Event Clocked from: Fast start-up bit = 0 back (Not clocked) through WUP0-15 +LPM bit = 0 pins RTC alarm RTT alarm USB wake-up Previous state saved Unchanged OFF WFE OFF +SLEEPDEEP (Not powered) bit = 1 WUP0-15 pins SM alarm RTC alarm RTT alarm Reset 1.5 A typ(4) (6) < 0.1 ms (6) 1. When considering wake-up time, the time required to start the PLL is not taken into account. Once started, the device works with the 4/8/12 MHz fast RC oscillator. The user has to add the PLL start-up time if it is needed in the system. The wake-up time is defined as the time taken for wake up until the first instruction is fetched. 2. The external loads on PIOs are not taken into account in the calculation. 3. Supply Monitor current consumption is not included. 4. Total Current consumption. 5. 5 A on VDDCORE, 15 A for total current consumption (using internal voltage regulator), 8 A for total current consumption (without using internal voltage regulator). 6. Depends on MCK frequency. 7. In this mode the core is supplied and not clocked but some peripherals can be clocked. 18 SAM3S8/SD8 Summary 11090BS-ATARM-22-Oct-13 SAM3S8/SD8 Summary 5.6 Wake-up Sources The wake-up events allow the device to exit the backup mode. When a wake-up event is detected, the Supply Controller performs a sequence which automatically reenables the core power supply and the SRAM power supply, if they are not already enabled. Figure 5-4. Wake-up Source SMEN sm_out RTCEN rtc_alarm Core Supply Restart RTTEN rtt_alarm WKUPT0 WKUP0 WKUPDBC WKUPEN1 WKUPIS1 SLCK WKUPS Debouncer Falling/Rising Edge Detector WKUPT15 WKUP15 WKUPIS0 Falling/Rising Edge Detector WKUPT1 WKUP1 WKUPEN0 WKUPEN15 WKUPIS15 Falling/Rising Edge Detector 19 11090BS-ATARM-22-Oct-13 5.7 Fast Startup The SAM3S8/SD8 allows the processor to restart in a few microseconds while the processor is in wait mode or in sleep mode. A fast start up can occur upon detection of a low level on one of the 19 wake-up inputs (WKUP0 to 15 + SM + RTC + RTT). The fast restart circuitry, as shown in Figure 5-5, is fully asynchronous and provides a fast startup signal to the Power Management Controller. As soon as the fast start-up signal is asserted, the PMC automatically restarts the embedded 4 MHz Fast RC oscillator, switches the master clock on this 4MHz clock and reenables the processor clock. Figure 5-5. Fast Start-Up Sources USBEN usb_wakeup RTCEN rtc_alarm RTTEN rtt_alarm FSTT0 WKUP0 Falling/Rising Edge Detector fast_restart FSTT1 WKUP1 Falling/Rising Edge Detector FSTT15 WKUP15 20 Falling/Rising Edge Detector SAM3S8/SD8 Summary 11090BS-ATARM-22-Oct-13 SAM3S8/SD8 Summary 6. Input/Output Lines The SAM3S8/SD8 has several kinds of input/output (I/O) lines such as general purpose I/Os (GPIO) and system I/Os. GPIOs can have alternate functionality due to multiplexing capabilities of the PIO controllers. The same PIO line can be used whether in I/O mode or by the multiplexed peripheral. System I/Os include pins such as test pins, oscillators, erase or analog inputs. 6.1 General Purpose I/O Lines GPIO Lines are managed by PIO Controllers. All I/Os have several input or output modes such as pull-up or pull-down, input Schmitt triggers, multi-drive (open-drain), glitch filters, debouncing or input change interrupt. Programming of these modes is performed independently for each I/O line through the PIO controller user interface. For more details, refer to the product "PIO Controller" section. The input/output buffers of the PIO lines are supplied through VDDIO power supply rail. The SAM3S8/SD8 embeds high speed pads able to handle up to 32 MHz for HSMCI (MCK/2), 45 MHz for SPI clock lines and 35 MHz on other lines. See AC Characteristics Section of the datasheet for more details. Typical pull-up and pull-down value is 100 k for all I/Os. Each I/O line also embeds an ODT (On-Die Termination), (see Figure 6-1 below). It consists of an internal series resistor termination scheme for impedance matching between the driver output (SAM3S8/SD8) and the PCB trace impedance preventing signal reflection. The series resistor helps to reduce IOs switching current (di/dt) thereby reducing in turn, EMI. It also decreases overshoot and undershoot (ringing) due to inductance of interconnect between devices or between boards. In conclusion ODT helps diminish signal integrity issues. Figure 6-1. On-Die Termination Z0 ~ Zout + Rodt ODT 36 Ohms Typ. Rodt Receiver SAM3 Driver with Zout ~ 10 Ohms 6.2 PCB Trace Z0 ~ 50 Ohms System I/O Lines System I/O lines are pins used by oscillators, test mode, reset and JTAG to name but a few. Described below in Table 6-1are the SAM3S8/SD8 system I/O lines shared with PIO lines. These pins are software configurable as general purpose I/O or system pins. At startup the default function of these pins is always used. 21 11090BS-ATARM-22-Oct-13 Table 6-1. System I/O Configuration Pin List. SYSTEM_IO bit number Notes: Default function after reset Other function Constraints for normal start Configuration (1) 12 ERASE PB12 Low Level at startup 10 DDM PB10 - 11 DDP PB11 - 7 TCK/SWCLK PB7 - 6 TMS/SWDIO PB6 - 5 TDO/TRACESWO PB5 - 4 TDI PB4 - - PA7 XIN32 - - PA8 XOUT32 - - PB9 XIN - - PB8 XOUT - In Matrix User Interface Registers (Refer to the System I/O Configuration Register in the "Bus Matrix" section of the datasheet.) See footnote (2) below See footnote (3) below 1. If PB12 is used as PIO input in user applications, a low level must be ensured at startup to prevent Flash erase before the user application sets PB12 into PIO mode, 2. In the product Datasheet Refer to: "Slow Clock Generator" of the "Supply Controller" section. 3. In the product Datasheet Refer to: "3 to 20 MHZ Crystal Oscillator" information in the "PMC" section. 6.2.1 Serial Wire JTAG Debug Port (SWJ-DP) Pins The SWJ-DP pins are TCK/SWCLK, TMS/SWDIO, TDO/SWO, TDI and commonly provided on a standard 20-pin JTAG connector defined by ARM. For more details about voltage reference and reset state, refer to Table 3-1 on page 5. At startup, SWJ-DP pins are configured in SWJ-DP mode to allow connection with debugging probe. Please refer to the "Debug and Test" Section of the product datasheet. SWJ-DP pins can be used as standard I/Os to provide users more general input/output pins when the debug port is not needed in the end application. Mode selection between SWJ-DP mode (System IO mode) and general IO mode is performed through the AHB Matrix Special Function Registers (MATRIX_SFR). Configuration of the pad for pull-up, triggers, debouncing and glitch filters is possible regardless of the mode. The JTAGSEL pin is used to select the JTAG boundary scan when asserted at a high level. It integrates a permanent pull-down resistor of about 15 k to GND, so that it can be left unconnected for normal operations. By default, the JTAG Debug Port is active. If the debugger host wants to switch to the Serial Wire Debug Port, it must provide a dedicated JTAG sequence on TMS/SWDIO and TCK/SWCLK which disables the JTAG-DP and enables the SW-DP. When the Serial Wire Debug Port is active, TDO/TRACESWO can be used for trace. The asynchronous TRACE output (TRACESWO) is multiplexed with TDO. So the asynchronous trace can only be used with SW-DP, not JTAG-DP. For more information about SW-DP and JTAG-DP switching, please refer to the "Debug and Test" Section. 22 SAM3S8/SD8 Summary 11090BS-ATARM-22-Oct-13 SAM3S8/SD8 Summary 6.3 Test Pin The TST pin is used for JTAG Boundary Scan Manufacturing Test or Fast Flash programming mode of the SAM3S8/SD8 series. The TST pin integrates a permanent pull-down resistor of about 15 k to GND, so that it can be left unconnected for normal operations. To enter fast programming mode, see the Fast Flash Programming Interface (FFPI) section. For more on the manufacturing and test mode, refer to the "Debug and Test" section of the product datasheet. 6.4 NRST Pin The NRST pin is bidirectional. It is handled by the on-chip reset controller and can be driven low to provide a reset signal to the external components or asserted low externally to reset the microcontroller. It will reset the Core and the peripherals except the Backup region (RTC, RTT and Supply Controller). There is no constraint on the length of the reset pulse and the reset controller can guarantee a minimum pulse length. The NRST pin integrates a permanent pull-up resistor to VDDIO of about 100 k. By default, the NRST pin is configured as an input. 6.5 ERASE Pin The ERASE pin is used to reinitialize the Flash content (and some of its NVM bits) to an erased state (all bits read as logic level 1). It integrates a pull-down resistor of about 100 k to GND, so that it can be left unconnected for normal operations. This pin is debounced by SCLK to improve the glitch tolerance. When the ERASE pin is tied high during less than 100 ms, it is not taken into account. The pin must be tied high during more than 220 ms to perform a Flash erase operation. The ERASE pin is a system I/O pin and can be used as a standard I/O. At startup, the ERASE pin is not configured as a PIO pin. If the ERASE pin is used as a standard I/O, startup level of this pin must be low to prevent unwanted erasing. Refer to Section 10.17 "Peripheral Signal Multiplexing on I/O Lines" on page 40. Also, if the ERASE pin is used as a standard I/O output, asserting the pin to low does not erase the Flash. 23 11090BS-ATARM-22-Oct-13 7. Processor and Architecture 7.1 ARM Cortex-M3 Processor * Version 2.0 * Thumb-2 (ISA) subset consisting of all base Thumb-2 instructions, 16-bit and 32-bit. * Harvard processor architecture enabling simultaneous instruction fetch with data load/store. * Three-stage pipeline. * Single cycle 32-bit multiply. * Hardware divide. * Thumb and Debug states. * Handler and Thread modes. * Low latency ISR entry and exit. 7.2 APB/AHB bridge The SAM3S8/SD8 embeds One Peripheral bridge: The peripherals of the bridge are clocked by MCK. 7.3 Matrix Masters The Bus Matrix of the SAM3S8/SD8 manages 4 masters, which means that each master can perform an access concurrently with others, to an available slave. Each master has its own decoder, which is defined specifically for each master. In order to simplify the addressing, all the masters have the same decodings. Table 7-1. 7.4 List of Bus Matrix Masters Master 0 Cortex-M3 Instruction/Data Master 1 Cortex-M3 System Master 2 Peripheral DMA Controller (PDC) Master 3 CRC Calculation Unit Matrix Slaves The Bus Matrix of the SAM3S8/SD8 manages 5 slaves. Each slave has its own arbiter, allowing a different arbitration per slave. Table 7-2. 24 List of Bus Matrix Slaves Slave 0 Internal SRAM Slave 1 Internal ROM Slave 2 Internal Flash Slave 3 External Bus Interface Slave 4 Peripheral Bridge SAM3S8/SD8 Summary 11090BS-ATARM-22-Oct-13 SAM3S8/SD8 Summary 7.5 Master to Slave Access All the Masters can normally access all the Slaves. However, some paths do not make sense, for example allowing access from the Cortex-M3 S Bus to the Internal ROM. Thus, these paths are forbidden or simply not wired, and shown as "-" in the following table. Table 7-3. SAM3S8_SD8 Master to Slave Access Masters Slaves 7.6 0 1 2 3 Cortex-M3 I/D Bus Cortex-M3 S Bus PDC CRCCU 0 Internal SRAM - X X X 1 Internal ROM X - X X 2 Internal Flash X - - X 3 External Bus Interface - X X X 4 Peripheral Bridge - X X - Peripheral DMA Controller * Handles data transfer between peripherals and memories * Low bus arbitration overhead - One Master Clock cycle needed for a transfer from memory to peripheral - Two Master Clock cycles needed for a transfer from peripheral to memory * Next Pointer management for reducing interrupt latency requirement The Peripheral DMA Controller handles transfer requests from the channel according to the following priorities (Low to High priorities): Table 7-4. Peripheral DMA Controller Instance name Channel T/R USART2 Transmit USART2 Receive PWM Transmit TWI1 Transmit TWI0 Transmit UART1 Transmit UART0 Transmit USART1 Transmit USART0 Transmit DACC Transmit SPI Transmit 25 11090BS-ATARM-22-Oct-13 Table 7-4. 7.7 Peripheral DMA Controller Instance name Channel T/R SSC Transmit HSMCI Transmit PIOA Receive TWI1 Receive TWI0 Receive UART1 Receive UART0 Receive USART1 Receive USART0 Receive ADC Receive SPI Receive SSC Receive HSMCI Receive Debug and Test Features * Debug access to all memory and registers in the system, including Cortex-M3 register bank when the core is running, halted, or held in reset. * Serial Wire Debug Port (SW-DP) and Serial Wire JTAG Debug Port (SWJ-DP) debug access * Flash Patch and Breakpoint (FPB) unit for implementing breakpoints and code patches * Data Watchpoint and Trace (DWT) unit for implementing watch points, data tracing, and system profiling * Instrumentation Trace Macrocell (ITM) for support of printf style debugging * IEEE(R)1149.1 JTAG Boundary scan on All Digital Pins 26 SAM3S8/SD8 Summary 11090BS-ATARM-22-Oct-13 SAM3S8/SD8 Summary 8. Product Mapping Figure 8-1. SAM3S8/SD8 Product Mapping 0x00000000 Code 0x00000000 Address memory space Peripherals 0x40000000 HSMCI Boot Memory Code 0x00400000 Internal Flash 0x00800000 Internal ROM 0x00C00000 1 MByte bit band regiion SSC 0x20000000 22 0x40008000 0x20100000 SRAM SPI Reserved Undefined 0x40010000 TC0 0x24000000 0x40000000 21 0x4000C000 0x22000000 Reserved 0x1FFFFFFF 18 0x40004000 32 MBytes bit band alias 23 TC0 24 TC0 External RAM 0x60000000 0x61000000 TC2 25 0x40014000 TC1 SMC Chip Select 0 TC1 +0x80 Peripherals 0x60000000 TC0 +0x40 External SRAM TC3 26 +0x40 TC1 SMC Chip Select 1 0xA0000000 0x62000000 TC1 0x63000000 SMC Chip Select 3 27 +0x80 Reserved SMC Chip Select 2 TC4 TC5 28 0x40018000 0xE0000000 0x64000000 TWI0 System Reserved 0x9FFFFFFF 19 0x4001C000 0xFFFFFFFF TWI1 20 0x40020000 0x400E0000 System Controller PWM USART1 0x400E0400 USART2 5 0x400E0600 16 0x40030000 UART0 Reserved 8 0x400E0740 15 0x4002C000 PMC ID 14 0x40028000 MATRIX block peripheral USART0 10 0x400E0200 offset 31 0x40024000 SMC 1 MByte bit band regiion 0x40034000 CHIPID UDP 0x400E0800 ADC 9 0x400E0A00 29 0x4003C000 EFC DACC 6 0x400E0C00 33 0x40038000 UART1 30 0x40040000 Reserved ACC 0x400E0E00 CRCCU 11 0x400E1000 Reserved 12 0x400E0000 PIOC System Controller 13 0x400E1400 0x400E2600 RSTC Reserved 1 +0x10 35 0x40048000 PIOB 0x400E1200 34 0x40044000 PIOA 0x40100000 SUPC Reserved +0x30 0x40200000 RTT 3 +0x50 0x40400000 32 MBytes bit band alias WDT Reserved 4 +0x60 0x60000000 RTC 2 +0x90 GPBR 0x400E1600 Reserved 0x4007FFFF 27 11090BS-ATARM-22-Oct-13 9. Memories 9.1 9.1.1 Embedded Memories Internal SRAM The SAM3S8 device (512-Kbytes, single bank flash) embeds a total of 64-Kbytes high-speed SRAM. The SAM3SD8 device (512-Kbytes, dual bank flash) embeds a total of 64-Kbytes high-speed SRAM. The SRAM is accessible over System Cortex-M3 bus at address 0x2000 0000. The SRAM is in the bit band region. The bit band alias region is from 0x2200 0000 and 0x23FF FFFF. 9.1.2 Internal ROM The SAM3S8/SD8 embeds an Internal ROM, which contains the SAM Boot Assistant (SAM-BA(R)), In Application Programming routines (IAP) and Fast Flash Programming Interface (FFPI). At any time, the ROM is mapped at address 0x0080 0000. 9.1.3 9.1.3.1 Embedded Flash Flash Overview The Flash of the SAM3S8 (512-Kbytes single bank flash) is organized in one bank of 2048 pages of 256 bytes. The Flash of the SAM3SD8 (512-Kbytes, dual bank flash) is organized in two banks of 1024 pages of 256 bytes each. The Flash contains a 128-byte write buffer, accessible through a 32-bit interface. 9.1.3.2 Flash Power Supply The Flash is supplied by VDDCORE. 9.1.3.3 Enhanced Embedded Flash Controller The Enhanced Embedded Flash Controller (EEFC) manages accesses performed by the masters of the system. It enables reading the Flash and writing the write buffer. It also contains a User Interface, mapped on the APB. The Enhanced Embedded Flash Controller ensures the interface of the Flash block with the 32bit internal bus. Its 128-bit wide memory interface increases performance. The user can choose between high performance or lower current consumption by selecting either 128-bit or 64-bit access. It also manages the programming, erasing, locking and unlocking sequences of the Flash using a full set of commands. One of the commands returns the embedded Flash descriptor definition that informs the system about the Flash organization, thus making the software generic. 28 SAM3S8/SD8 Summary 11090BS-ATARM-22-Oct-13 SAM3S8/SD8 Summary 9.1.3.4 Flash Speed The user needs to set the number of wait states depending on the frequency used: For more details, refer to the "AC Characteristics" sub-section of the product "Electrical Characteristics". 9.1.3.5 Lock Regions Several lock bits are used to protect write and erase operations on lock regions. A lock region is composed of several consecutive pages, and each lock region has its associated lock bit. Table 9-1. Lock bit number Product Number of lock bits Lock region size SAM3S8/SD8 16 32 kbytes (128 pages) If a locked-region's erase or program command occurs, the command is aborted and the EEFC triggers an interrupt. The lock bits are software programmable through the EEFC User Interface. The command "Set Lock Bit" enables the protection. The command "Clear Lock Bit" unlocks the lock region. Asserting the ERASE pin clears the lock bits, thus unlocking the entire Flash. 9.1.3.6 Security Bit Feature The SAM3S8/SD8 features a security bit, based on a specific General Purpose NVM bit (GPNVM bit 0). When the security is enabled, any access to the Flash, SRAM, Core Registers and Internal Peripherals either through the ICE interface or through the Fast Flash Programming Interface, is forbidden. This ensures the confidentiality of the code programmed in the Flash. This security bit can only be enabled, through the command "Set General Purpose NVM Bit 0" of the EEFC User Interface. Disabling the security bit can only be achieved by asserting the ERASE pin at 1, and after a full Flash erase is performed. When the security bit is deactivated, all accesses to the Flash, SRAM, Core registers, Internal Peripherals are permitted. It is important to note that the assertion of the ERASE pin should always be longer than 200 ms. As the ERASE pin integrates a permanent pull-down, it can be left unconnected during normal operation. However, it is safer to connect it directly to GND for the final application. 9.1.3.7 Calibration Bits NVM bits are used to calibrate the brownout detector and the voltage regulator. These bits are factory configured and cannot be changed by the user. The ERASE pin has no effect on the calibration bits. 9.1.3.8 Unique Identifier Each device integrates its own 128-bit unique identifier. These bits are factory configured and cannot be changed by the user. The ERASE pin has no effect on the unique identifier. 9.1.3.9 Fast Flash Programming Interface The Fast Flash Programming Interface allows programming the device through either a serial JTAG interface or through a multiplexed fully-handshaked parallel port. It allows gang programming with market-standard industrial programmers. 29 11090BS-ATARM-22-Oct-13 The FFPI supports read, page program, page erase, full erase, lock, unlock and protect commands. 9.1.3.10 SAM-BA Boot The SAM-BA Boot is a default Boot Program which provides an easy way to program in-situ the on-chip Flash memory. The SAM-BA Boot Assistant supports serial communication via the UART and USB. The SAM-BA Boot provides an interface with SAM-BA Graphic User Interface (GUI). The SAM-BA Boot is in ROM and is mapped in Flash at address 0x0 when GPNVM bit 1 is set to 0. 9.1.3.11 GPNVM Bits The SAM3S8 features two GPNVM bits, whereas SAM3SD8 features three GPNVM bits. These bits can be cleared or set respectively through the commands "Clear GPNVM Bit" and "Set GPNVM Bit" of the EEFC User Interface. The Flash of the SAM3S8 is composed of 512 Kbytes in a single bank, while the SAM3SD8 Flash is composed of dual banks, each containing 256 Kbytes. The dual-bank function enables programming one bank while the other one is read (typically while the application code is running). Only one EEFC (Flash controller) controls the two banks. Note that it is not possible to program simultaneously, or read simultaneously, the dual banks of the Flash. The first bank of 256 Kbytes is called Bank 0 and the second bank of 256 Kbytes, Bank 1. The SAM3SD8 embeds an additional GPNVM bit: GPNVM2. Table 9-2. 9.1.4 General-purpose Non volatile Memory Bits GPNVMBit[#] Function 0 Security bit 1 Boot mode selection 2 Bank selection (Bank 0 or Bank 1) Only on SAM3SD8 Boot Strategies The system always boots at address 0x0. To ensure maximum boot possibilities, the memory layout can be changed via GPNVM. A general purpose NVM (GPNVM) bit is used to boot either on the ROM (default) or from the Flash. The GPNVM bit can be cleared or set respectively through the commands "Clear General-purpose NVM Bit" and "Set General-purpose NVM Bit" of the EEFC User Interface. Setting GPNVM Bit 1 selects the boot from the Flash, clearing it selects the boot from the ROM. Asserting ERASE clears the GPNVM Bit 1 and thus selects the boot from the ROM by default. Setting the GPNVM Bit 2 selects bank 1, clearing it selects the boot from bank 0. Asserting ERASE clears the GPNVM Bit 2 and thus selects the boot from bank 0 by default. 30 SAM3S8/SD8 Summary 11090BS-ATARM-22-Oct-13 SAM3S8/SD8 Summary 9.2 External Memories The SAM3S8/SD8 features one External Bus Interface to provide an interface to a wide range of external memories and to any parallel peripheral. 9.2.1 Static Memory Controller * 16-Mbyte Address Space per Chip Select * 8- bit Data Bus * Word, Halfword, Byte Transfers * Programmable Setup, Pulse And Hold Time for Read Signals per Chip Select * Programmable Setup, Pulse And Hold Time for Write Signals per Chip Select * Programmable Data Float Time per Chip Select * External Wait Request * Automatic Switch to Slow Clock Mode * Asynchronous Read in Page Mode Supported: Page Size Ranges from 4 to 32 Bytes * NAND Flash additional logic supporting NAND Flash with Multiplexed Data/Address buses * Hardware Configurable number of chip selects from 1 to 4 * Programmable timing on a per chip select basis 10. System Controller The System Controller is a set of peripherals, which allow handling of key elements of the system, such as power, resets, clocks, time, interrupts, watchdog, etc... See the system controller block diagram in Figure 10-1 on page 32. 31 11090BS-ATARM-22-Oct-13 Figure 10-1. System Controller Block Diagram VDDIO VDDOUT vr_on vr_mode Software Controlled Voltage Regulator VDDIO Supply Controller Zero-Power Power-on Reset PIOA/B/C Input/Output Buffers ON Supply Monitor (Backup) VDDIN PIOx out Analog Comparator WKUP0 - WKUP15 General Purpose Backup Registers ADVREF rtc_nreset SLCK RTC ADx ADC Analog Circuitry DAC Analog Circuitry rtc_alarm DACx VDDIO rtt_nreset SLCK RTT rtt_alarm XIN32 Xtal 32 kHz Oscillator Embedded 32 kHz RC Oscillator Slow Clock SLCK bod_core_on lcore_brown_out Brownout Detector (Core) osc32k_rc_en VDDCORE SRAM vddcore_nreset Backup Power Supply DDM vddcore_nreset XTALSEL XOUT32 DDP USB Transeivers osc32k_xtal_en Reset Controller NRST proc_nreset periph_nreset ice_nreset Peripherals Matrix Peripheral Bridge Cortex-M3 FSTT0 - FSTT15 SLCK Embedded 12 / 8 / 4 MHz RC Oscillator XIN XOUT Flash Main Clock MAINCK 3 - 20 MHz XTAL Oscillator Power Management Controller Master Clock MCK PLLACK MAINCK PLLA SLCK VDDIO MAINCK Watchdog Timer PLLBCK PLLB Core Power Supply FSTT0 - FSTT15 are possible Fast Startup sources, generated by WKUP0 - WKUP15 pins, but are not physical pins. 32 SAM3S8/SD8 Summary 11090BS-ATARM-22-Oct-13 SAM3S8/SD8 Summary 10.1 System Controller and Peripherals Mapping Please refer to Section 8-1 "SAM3S8/SD8 Product Mapping" on page 27. All the peripherals are in the bit band region and are mapped in the bit band alias region. 10.2 Power-on-Reset, Brownout and Supply Monitor The SAM3S8/SD8 embeds three features to monitor, warn and/or reset the chip: * Power-on-Reset on VDDIO * Brownout Detector on VDDCORE * Supply Monitor on VDDIO 10.2.1 Power-on-Reset The Power-on-Reset monitors VDDIO. It is always activated and monitors voltage at start up but also during power down. If VDDIO goes below the threshold voltage, the entire chip is reset. For more information, refer to the Electrical Characteristics section of the datasheet. 10.2.2 Brownout Detector on VDDCORE The Brownout Detector monitors VDDCORE. It is active by default. It can be deactivated by software through the Supply Controller (SUPC_MR). It is especially recommended to disable it during low-power modes such as wait or sleep modes. If VDDCORE goes below the threshold voltage, the reset of the core is asserted. For more information, refer to the Supply Controller (SUPC) and Electrical Characteristics sections of the datasheet. 10.2.3 10.3 Supply Monitor on VDDIO The Supply Monitor monitors VDDIO. It is not active by default. It can be activated by software and is fully programmable with 16 steps for the threshold (between 1.9V to 3.4V). It is controlled by the Supply Controller (SUPC). A sample mode is possible. It allows to divide the supply monitor power consumption by a factor of up to 2048. For more information, refer to the SUPC and Electrical Characteristics sections of the datasheet. Reset Controller The Reset Controller is based on a Power-on-Reset cell, and a Supply Monitor on VDDCORE. The Reset Controller is capable to return to the software the source of the last reset, either a general reset, a wake-up reset, a software reset, a user reset or a watchdog reset. The Reset Controller controls the internal resets of the system and the NRST pin input/output. It is capable to shape a reset signal for the external devices, simplifying to a minimum connection of a push-button on the NRST pin to implement a manual reset. The configuration of the Reset Controller is saved as supplied on VDDIO. 10.4 Supply Controller (SUPC) The Supply Controller controls the power supplies of each section of the processor and the peripherals (via Voltage regulator control) The Supply Controller has its own reset circuitry and is clocked by the 32 kHz Slow clock generator. 33 11090BS-ATARM-22-Oct-13 The reset circuitry is based on a zero-power power-on reset cell and a brownout detector cell. The zero-power power-on reset allows the Supply Controller to start properly, while the software-programmable brownout detector allows detection of either a battery discharge or main voltage loss. The Slow Clock generator is based on a 32 kHz crystal oscillator and an embedded 32 kHz RC oscillator. The Slow Clock defaults to the RC oscillator, but the software can enable the crystal oscillator and select it as the Slow Clock source. The Supply Controller starts up the device by sequentially enabling the internal power switches and the Voltage Regulator, then it generates the proper reset signals to the core power supply. It also enables to set the system in different low-power modes and to wake it up from a wide range of events. 10.5 Clock Generator The Clock Generator is made up of: * One Low-power 32768Hz Slow Clock Oscillator with bypass mode * One Low-power RC Oscillator * One 3-20 MHz Crystal Oscillator, which can be bypassed * One Fast RC Oscillator, factory programmed. Three output frequencies can be selected: 4, 8 or 12 MHz. By default 4 MHz is selected. * One 60 to 130 MHz PLL (PLLB) providing a clock for the USB Full Speed Controller * One 60 to 130 MHz programmable PLL (PLLA), provides the clock, MCK to the processor and peripherals. The PLLA input frequency is from 3.5 MHz to 20 MHz. 34 SAM3S8/SD8 Summary 11090BS-ATARM-22-Oct-13 SAM3S8/SD8 Summary Figure 10-2. Clock Generator Block Diagram Clock Generator XTALSEL On Chip 32k RC OSC XIN32 XOUT32 XIN Slow Clock SLCK Slow Clock Oscillator 12M Main Oscillator Main Clock MAINCK XOUT On Chip 12/8/4 MHz RC OSC MAINSEL PLL and Divider B PLLB Clock PLLBCK PLL and Divider A PLLA Clock PLLACK Status Control Power Management Controller 10.6 Power Management Controller The Power Management Controller provides all the clock signals to the system. It provides: * the Processor Clock, HCLK * the Free running processor clock, FCLK * the Cortex SysTick external clock * the Master Clock, MCK, in particular to the Matrix and the memory interfaces * the USB Clock, UDPCK * independent peripheral clocks, typically at the frequency of MCK * three programmable clock outputs: PCK0, PCK1 and PCK2 The Supply Controller selects between the 32 kHz RC oscillator or the crystal oscillator. The unused oscillator is disabled automatically so that power consumption is optimized. By default, at startup the chip runs out of the Master Clock using the fast RC oscillator running at 4 MHz. The user can trim the 8 and 12 MHz RC Oscillator frequency by software. 35 11090BS-ATARM-22-Oct-13 Figure 10-3. Power Management Controller Block Diagram Processor Clock Controller HCK int Sleep Mode Divider /8 SystTick FCLK Master Clock Controller SLCK MAINCK PLLACK PLLBCK Prescaler /1,/2,/4,...,/64 MCK Peripherals Clock Controller periph_clk[..] ON/OFF Programmable Clock Controller SLCK MAINCK PLLACK PLLBCK ON/OFF Prescaler /1,/2,/4,...,/64 pck[..] USB Clock Controller ON/OFF PLLBCK UDPCK The SysTick calibration value is fixed at 8000, which allows the generation of a time base of 1 ms with SysTick clock at 8 MHz (max HCLK/8 = 64 MHz/8) 10.7 Watchdog Timer * 16-bit key-protected only-once Programmable Counter * Windowed, prevents the processor to be in a deadlock on the watchdog access 10.8 SysTick Timer * 24-bit down counter * Self-reload capability * Flexible System timer 36 SAM3S8/SD8 Summary 11090BS-ATARM-22-Oct-13 SAM3S8/SD8 Summary 10.9 Real-Time Timer * Real-Time Timer, allowing backup of time with different accuracies - 32-bit Free-running backup Counter - Integrates a 16-bit programmable prescaler running on slow clock - Alarm Register capable to generate a wake-up of the system through the Shut Down Controller 10.10 Real Time Clock * Low power consumption * Full asynchronous design * Two hundred year Gregorian and Persian calendar * Programmable Periodic Interrupt * Trimmable 32.7682 kHz crystal oscillator clock source * Alarm and update parallel load * Control of alarm and update Time/Calendar Data In * Waveform output capability on GPIO pins in low power modes 10.11 General-Purpose Backed-up Registers * Eight 32-bit backup general-purpose registers 10.12 Nested Vectored Interrupt Controller * Thirty maskable external interrupts * Sixteen priority levels * Processor state automatically saved on interrupt entry, and restored on * Dynamic reprioritizing of interrupts * Priority grouping. - selection of pre-empting interrupt levels and non pre-empting interrupt levels. * Support for tail-chaining and late arrival of interrupts. - back-to-back interrupt processing without the overhead of state saving and restoration between interrupts. * Processor state automatically saved on interrupt entry, and restored on interrupt exit, with no instruction overhead. 37 11090BS-ATARM-22-Oct-13 10.13 Chip Identification * Chip Identifier (CHIPID) registers permit recognition of the device and its revision. Table 10-1. SAM3S8/SD8 Hip IDs Register Chip Name Flash Size (KBytes) Pin Count CHIPID_CIDR CHIPID_EXID SAM3S8B (Rev A) 512 64 0x289B0A60 0x0 SAM3S8C (Rev A) 512 100 0x28AB0A60 0x0 SAM3SD8B (Rev A) 512 64 0x299B0A60 0x0 SAM3SD8C (Rev A) 512 100 0x29AB0A60 0x0 * JTAG ID: 0x05B2D03F 10.14 UART * Two-pin UART - Implemented features are 100% compatible with the standard Atmel USART - Independent receiver and transmitter with a common programmable Baud Rate Generator - Even, Odd, Mark or Space Parity Generation - Parity, Framing and Overrun Error Detection - Automatic Echo, Local Loopback and Remote Loopback Channel Modes - Support for two PDC channels with connection to receiver and transmitter 10.15 PIO Controllers * 3 PIO Controllers, PIOA, PIOB and PIOC (100-pin version only) controlling a maximum of 79 I/O Lines * Each PIO Controller controls up to 32 programmable I/O Lines * Fully programmable through Set/Clear Registers Table 10-2. PIO available according to pin count Version 64 pin 100 pin PIOA 32 32 PIOB 15 15 PIOC - 32 * Multiplexing of four peripheral functions per I/O Line * For each I/O Line (whether assigned to a peripheral or used as general purpose I/O) - Input change interrupt - Programmable Glitch filter - Programmable debouncing filter - Multi-drive option enables driving in open drain - Programmable pull-up on each I/O line - Pin data status register, supplies visibility of the level on the pin at any time - Additional interrupt modes on a programmable event: rising edge, falling edge, low level or high level 38 SAM3S8/SD8 Summary 11090BS-ATARM-22-Oct-13 SAM3S8/SD8 Summary - Lock of the configuration by the connected peripheral * Synchronous output, provides set and clear of several I/O lines in a single write * Write Protect Registers * Programmable Schmitt trigger inputs * Parallel capture mode - Can be used to interface a CMOS digital image sensor, an ADC.... - One clock, 8-bit parallel data and two data enable on I/O lines - Data can be sampled one time out of two (for chrominance sampling only) - Supports connection of one Peripheral DMA Controller channel (PDC) which offers buffer reception without processor intervention 10.16 Peripheral Identifiers Table 10-3 defines the Peripheral Identifiers of the SAM3S8/SD8. A peripheral identifier is required for the control of the peripheral interrupt with the Nested Vectored Interrupt Controller and control of the peripheral clock with the Power Management Controller. Table 10-3. Peripheral Identifiers PMC Clock Control Instance ID Instance Name NVIC Interrupt Instance Description 0 SUPC X Supply Controller 1 RSTC X Reset Controller 2 RTC X Real Time Clock 3 RTT X Real Time Timer 4 WDT X Watchdog Timer 5 PMC X Power Management Controller 6 EEFC X Enhanced Embedded Flash Controller 7 - - Reserved 8 UART0 X X UART 0 9 UART1 X X UART 1 10 SMC X X Static Memory Controller 11 PIOA X X Parallel I/O Controller A 12 PIOB X X Parallel I/O Controller B 13 PIOC X X Parallel I/O Controller C 14 USART0 X X USART 0 15 USART1 X X USART 1 16 USART2 X X USART 2 (SAM3SD8 100 pins only) 17 - - - Reserved 18 HSMCI X X Multimedia Card Interface 19 TWI0 X X Two Wire Interface 0 20 TWI1 X X Two Wire Interface 1 21 SPI X X Serial Peripheral Interface 39 11090BS-ATARM-22-Oct-13 Table 10-3. Peripheral Identifiers (Continued) Instance ID Instance Name NVIC Interrupt PMC Clock Control 22 SSC X X Synchronous Serial Controller 23 TC0 X X Timer/Counter 0 24 TC1 X X Timer/Counter 1 25 TC2 X X Timer/Counter 2 26 TC3 X X Timer/Counter 3 27 TC4 X X Timer/Counter 4 28 TC5 X X Timer/Counter 5 29 ADC X X Analog To Digital Converter 30 DACC X X Digital To Analog Converter 31 PWM X X Pulse Width Modulation 32 CRCCU X X CRC Calculation Unit 33 ACC X X Analog Comparator 34 UDP X X USB Device Port Instance Description 10.17 Peripheral Signal Multiplexing on I/O Lines The SAM3S8/SD8 features 2 PIO controllers on 64-pin versions (PIOA and PIOB) or 3 PIO controllers on the 100-pin version (PIOA, PIOB and PIOC), that multiplex the I/O lines of the peripheral set. The SAM3S8/SD8 64-pin and 100-pin PIO Controllers control up to 32 lines. Each line can be assigned to one of three peripheral functions: A, B or C. The multiplexing tables in the following paragraphs define how the I/O lines of the peripherals A, B and C are multiplexed on the PIO Controllers. The column "Comments" has been inserted in this table for the user's own comments; it may be used to track how pins are defined in an application. Note that some peripheral functions which are output only, might be duplicated within the tables. 40 SAM3S8/SD8 Summary 11090BS-ATARM-22-Oct-13 SAM3S8/SD8 Summary 10.17.1 PIO Controller A Multiplexing Table 10-4. Multiplexing on PIO Controller A (PIOA) I/O Line Peripheral A Peripheral B Peripheral C Peripheral D Extra Function System Function Comments PA0 PWMH0 TIOA0 A17 WKUP0 PA1 PWMH1 TIOB0 A18 WKUP1 PA2 PWMH2 SCK0 DATRG WKUP2 PA3 TWD0 NPCS3 PA4 TWCK0 TCLK0 WKUP3 PA5 RXD0 NPCS3 WKUP4 PA6 TXD0 PCK0 PA7 RTS0 PWMH3 PA8 CTS0 ADTRG PA9 URXD0 NPCS1 PA10 UTXD0 NPCS2 PA11 NPCS0 PWMH0 PA12 MISO PWMH1 PA13 MOSI PWMH2 PA14 SPCK PWMH3 PA15 TF TIOA1 PWML3 PIODCEN1 WKUP14 PA16 TK TIOB1 PWML2 PIODCEN2 WKUP15 PA17 TD PCK1 PWMH3 AD0 PA18 RD PCK2 A14 AD1 PA19 RK PWML0 A15 AD2/WKUP9 PA20 RF PWML1 A16 AD3/WKUP10 PA21 RXD1 PCK1 PA22 TXD1 NPCS3 NCS2 PA23 SCK1 PWMH0 A19 PIODCCLK 64/100 pins versions PA24 RTS1 PWMH1 A20 PIODC0 64/100 pins versions PA25 CTS1 PWMH2 A23 PIODC1 64/100 pins versions PA26 DCD1 TIOA2 MCDA2 PIODC2 64/100 pins versions PA27 DTR1 TIOB2 MCDA3 PIODC3 64/100 pins versions PA28 DSR1 TCLK1 MCCDA PIODC4 64/100 pins versions PA29 RI1 TCLK2 MCCK PIODC5 64/100 pins versions PA30 PWML2 NPCS2 MCDA0 PIODC6 PA31 NPCS1 PCK2 MCDA1 PIODC7 XIN32 WKUP5 PWMFI0 XOUT32 WKUP6 WKUP7 WKUP8 AD8 64/100 pins versions AD9 64/100 pins versions WKUP11 64/100 pins versions 64/100 pins versions 41 11090BS-ATARM-22-Oct-13 10.17.2 PIO Controller B Multiplexing Table 10-5. I/O Line Multiplexing on PIO Controller B (PIOB) Peripheral A Peripheral B Peripheral C Extra Function PB0 PWMH0 AD4/RTCOUT0 PB1 PWMH1 AD5/RTCOUT1 PB2 URXD1 NPCS2 AD6/WKUP12 PB3 UTXD1 PCK2 AD7 PB4 TWD1 PWMH2 PB5 TWCK1 PWML0 System Function Comments TDI WKUP13 TDO/TRACESWO PB6 TMS/SWDIO PB7 TCK/SWCLK PB8 XOUT PB9 XIN PB10 DDM PB11 DDP PB12 PWML1 PB13 PWML2 PCK0 DAC0 64/00 pins versions PB14 NPCS1 PWMH3 DAC1 64/100 pins versions 42 ERASE SAM3S8/SD8 Summary 11090BS-ATARM-22-Oct-13 SAM3S8/SD8 Summary 10.17.3 PIO Controller C Multiplexing Table 10-6. I/O Line Multiplexing on PIO Controller C (PIOC) Peripheral C Extra Function System Function Peripheral A Peripheral B Comments PC0 D0 PWML0 100 pin version PC1 D1 PWML1 100 pin version PC2 D2 PWML2 100 pin version PC3 D3 PWML3 100 pin version PC4 D4 NPCS1 100 pin version PC5 D5 100 pin version PC6 D6 100 pin version PC7 D7 100 pin version PC8 NWE 100 pin version (1) PC9 NANDOE RXD2 100 pin version PC10 NANDWE TXD2(1) 100 pin version PC11 NRD PC12 NCS3 PC13 NWAIT PWML0 PC14 NCS0 SCK2(1) PC15 NCS1 PWML1 PC16 A21/NANDALE 100 pin version AD12 100 pin version AD10 100 pin version 100 pin version AD11 100 pin version (1) 100 pin version RTS2 PC17 A22/NANDCLE PC18 A0 PWMH0 100 pin version PC19 A1 PWMH1 100 pin version PC20 A2 PWMH2 100 pin version PC21 A3 PWMH3 100 pin version PC22 A4 PWML3 100 pin version PC23 A5 TIOA3 100 pin version PC24 A6 TIOB3 100 pin version PC25 A7 TCLK3 100 pin version PC26 A8 TIOA4 100 pin version PC27 A9 TIOB4 100 pin version PC28 A10 TCLK4 100 pin version PC29 A11 TIOA5 AD13 100 pin version PC30 A12 TIOB5 AD14 100 pin version PC31 A13 TCLK5 Note: CTS2 100 pin version (1) 100 pin version 1. USART2 only on SAM3SD8 in 100 pin package. 43 11090BS-ATARM-22-Oct-13 11. Embedded Peripherals Overview 11.1 Serial Peripheral Interface (SPI) * Supports communication with serial external devices - Four chip selects with external decoder support allow communication with up to 15 peripherals - Serial memories, such as DataFlash(R) and 3-wire EEPROMs - Serial peripherals, such as ADCs, DACs, LCD Controllers, CAN Controllers and Sensors - External co-processors * Master or slave serial peripheral bus interface - 8- to 16-bit programmable data length per chip select - Programmable phase and polarity per chip select - Programmable transfer delays between consecutive transfers and between clock and data per chip select - Programmable delay between consecutive transfers - Selectable mode fault detection * Connection to PDC channel capabilities optimizes data transfers - One channel for the receiver, one channel for the transmitter - Next buffer support 11.2 Two Wire Interface (TWI) * Master, Multi-Master and Slave Mode Operation * Compatibility with Atmel two-wire interface, serial memory and I2C compatible devices * One, two or three bytes for slave address * Sequential read/write operations * Bit Rate: Up to 400 kbit/s * General Call Supported in Slave Mode * Connecting to PDC channel capabilities optimizes data transfers in Master Mode only - One channel for the receiver, one channel for the transmitter - Next buffer support 11.3 Universal Asynchronous Receiver Transceiver (UART) * Two-pin UART - Independent receiver and transmitter with a common programmable Baud Rate Generator - Even, Odd, Mark or Space Parity Generation - Parity, Framing and Overrun Error Detection - Automatic Echo, Local Loopback and Remote Loopback Channel Modes - Support for two PDC channels with connection to receiver and transmitter 44 SAM3S8/SD8 Summary 11090BS-ATARM-22-Oct-13 SAM3S8/SD8 Summary 11.4 USART * Programmable Baud Rate Generator * 5- to 9-bit full-duplex synchronous or asynchronous serial communications - 1, 1.5 or 2 stop bits in Asynchronous Mode or 1 or 2 stop bits in Synchronous Mode - Parity generation and error detection - Framing error detection, overrun error detection - MSB- or LSB-first - Optional break generation and detection - By 8 or by-16 over-sampling receiver frequency - Hardware handshaking RTS-CTS - Receiver time-out and transmitter timeguard - Optional Multi-drop Mode with address generation and detection - Optional Manchester Encoding - Full modem line support on USART1 (DCD-DSR-DTR-RI) * RS485 with driver control signal * ISO7816, T = 0 or T = 1 Protocols for interfacing with smart cards - NACK handling, error counter with repetition and iteration limit * SPI Mode - Master or Slave - Serial Clock programmable Phase and Polarity - SPI Serial Clock (SCK) Frequency up to MCK/4 * IrDA modulation and demodulation - Communication at up to 115.2 Kbps * Test Modes - Remote Loopback, Local Loopback, Automatic Echo 11.5 Synchronous Serial Controller (SSC) * Provides serial synchronous communication links used in audio and telecom applications (with CODECs in Master or Slave Modes, I2S, TDM Buses, Magnetic Card Reader) * Contains an independent receiver and transmitter and a common clock divider * Offers configurable frame sync and data length * Receiver and transmitter can be programmed to start automatically or on detection of different event on the frame sync signal * Receiver and transmitter include a data signal, a clock signal and a frame synchronization signal 11.6 Timer Counter (TC) * Six 16-bit Timer Counter Channels * Wide range of functions including: - Frequency Measurement - Event Counting 45 11090BS-ATARM-22-Oct-13 - Interval Measurement - Pulse Generation - Delay Timing - Pulse Width Modulation - Up/down Capabilities * Each channel is user-configurable and contains: - Three external clock inputs - Five internal clock inputs - Two multi-purpose input/output signals * Two global registers that act on all three TC Channels * Quadrature decoder - Advanced line filtering - Position / revolution / speed * 2-bit Gray Up/Down Counter for Stepper Motor 11.7 Pulse Width Modulation Controller (PWM) * One Four-channel 16-bit PWM Controller, 16-bit counter per channel * Common clock generator, providing Thirteen Different Clocks - A Modulo n counter providing eleven clocks - Two independent Linear Dividers working on modulo n counter outputs - High Frequency Asynchronous clocking mode * Independent channel programming - Independent Enable Disable Commands - Independent Clock Selection - Independent Period and Duty Cycle, with Double Buffering - Programmable selection of the output waveform polarity - Programmable center or left aligned output waveform - Independent Output Override for each channel - Independent complementary Outputs with 12-bit dead time generator for each channel - Independent Enable Disable Commands - Independent Clock Selection - Independent Period and Duty Cycle, with Double Buffering * Synchronous Channel mode - Synchronous Channels share the same counter - Mode to update the synchronous channels registers after a programmable number of periods * Connection to one PDC channel - Provides Buffer transfer without processor intervention, to update duty cycle of synchronous channels * Two independent event lines which can send up to 4 triggers on ADC within a period 46 SAM3S8/SD8 Summary 11090BS-ATARM-22-Oct-13 SAM3S8/SD8 Summary * One programmable Fault Input providing an asynchronous protection of outputs * Stepper motor control (2 Channels) 11.8 High Speed Multimedia Card Interface (HSMCI) * 4-bit or 1-bit Interface * Compatibility with MultiMedia Card Specification Version 4.3 * Compatibility with SD and SDHC Memory Card Specification Version 2.0 * Compatibility with SDIO Specification Version V1.1. * Compatibility with CE-ATA Specification 1.1 * Cards clock rate up to Master Clock divided by 2 * Boot Operation Mode support * High Speed mode support * Embedded power management to slow down clock rate when not used * MCI has one slot supporting - One MultiMediaCard bus (up to 30 cards) or - One SD Memory Card - One SDIO Card * Support for stream, block and multi-block data read and write 11.9 USB Device Port (UDP) * USB V2.0 full-speed compliant,12 Mbits per second. * Embedded USB V2.0 full-speed transceiver * Embedded 2688-byte dual-port RAM for endpoints * Eight endpoints - Endpoint 0: 64bytes - Endpoint 1 and 2: 64 bytes ping-pong - Endpoint 3: 64 bytes - Endpoint 4 and 5: 512 bytes ping-pong - Endpoint 6 and 7: 64 bytes ping-pong - Ping-pong Mode (two memory banks) for Isochronous and bulk endpoints * Suspend/resume logic * Integrated Pull-up on DDP * Pull-down resistor on DDM and DDP when disabled 11.10 Analog-to-Digital Converter (ADC12B) * up to 16 Channels, 12-bit ADC * 10/12-bit resolution * up to 1 MSample/s * Programmable conversion sequence conversion on each channel * Integrated temperature sensor * Automatic calibration mode 47 11090BS-ATARM-22-Oct-13 * Single ended/differential conversion * Programmable gain: 1, 2, 4 11.11 Digital-to-Analog Converter (DAC) * Up to 2 channel 12-bit DAC * Up to 2 mega-samples conversion rate in single channel mode * Flexible conversion range * Multiple trigger sources for each channel * 2 Sample/Hold (S/H) outputs * Built-in offset and gain calibration * Possible to drive output to ground * Possible to use as input to analog comparator or ADC (as an internal wire and without S/H stage) * Two PDC channels * Power reduction mode 11.12 Static Memory Controller * 16-Mbyte Address Space per Chip Select * 8- bit Data Bus * Word, Halfword, Byte Transfers * Byte Write or Byte Select Lines * Programmable Setup, Pulse And Hold Time for Read Signals per Chip Select * Programmable Setup, Pulse And Hold Time for Write Signals per Chip Select * Programmable Data Float Time per Chip Select * Compliant with LCD Module * External Wait Request * Automatic Switch to Slow Clock Mode * Asynchronous Read in Page Mode Supported: Page Size Ranges from 4 to 32 Bytes * NAND Flash additional logic supporting NAND Flash with Multiplexed Data/Address buses * Hardware Configurable number of chip select from 1 to 4 * Programmable timing on a per chip select basis 11.13 Analog Comparator * One analog comparator * High speed option vs. low-power option - 170 A/xx ns active current consumption/propagation delay - 20 A/xx ns active current consumption/propagation delay * Selectable input hysteresis - 0, 20 mV, 50 mV * Minus input selection: - DAC outputs 48 SAM3S8/SD8 Summary 11090BS-ATARM-22-Oct-13 SAM3S8/SD8 Summary - Temperature Sensor - ADVREF - AD0 to AD3 ADC channels * Plus input selection: - All analog inputs * output selection: - Internal signal - external pin - selectable inverter * window function * Interrupt on: - Rising edge, Falling edge, toggle - Signal above/below window, signal inside/outside window 11.14 Cyclic Redundancy Check Calculation Unit (CRCCU) * 32-bit cyclic redundancy check automatic calculation * CRC calculation between two addresses of the memory 49 11090BS-ATARM-22-Oct-13 12. Package Drawings The SAM3S8/SD8 series devices are available in LQFP, QFN and TFBGA packages. Figure 12-1. 100-lead LQFP Package Mechanical Drawing Note : 1. This drawing is for general information only. Refer to JEDEC Drawing MS-026 for additional information. 50 SAM3S8/SD8 Summary 11090BS-ATARM-22-Oct-13 SAM3S8/SD8 Summary Figure 12-2. 100-ball TFBGA Package Mechanical Drawing 51 11090BS-ATARM-22-Oct-13 Figure 12-3. 64-lead LQFP Package Mechanical Drawing Table 12-1. Symbol 64-lead LQFP Package Dimensions (in mm) Millimeter Nom Max Min Nom Max A - - 1.60 - - 0.063 A1 0.05 - 0.15 0.002 - 0.006 A2 1.35 1.40 1.45 0.053 0.055 0.057 D 12.00 BSC 0.472 BSC D1 10.00 BSC 0.383 BSC E 12.00 BSC 0.472 BSC E1 10.00 BSC R2 0.08 R1 0.08 q 0 1 0 - 0.383 BSC 0.20 0.003 - 0.008 - - 0.003 - - 3.5 7 0 3.5 7 - - 0 - - 2 11 12 13 11 12 13 3 11 12 13 11 12 13 c 0.09 - 0.20 0.004 - 0.008 L 0.45 0.60 0.75 0.018 0.024 0.030 L1 52 Inch Min 1.00 REF 0.039 REF SAM3S8/SD8 Summary 11090BS-ATARM-22-Oct-13 SAM3S8/SD8 Summary Table 12-1. Symbol 64-lead LQFP Package Dimensions (in mm) (Continued) Millimeter Min Nom Inch Max Min Nom Max S 0.20 - - 0.008 - - b 0.17 0.20 0.27 0.007 0.008 0.011 e 0.50 BSC. 0.020 BSC. D2 7.50 0.285 E2 7.50 0.285 aaa 0.20 0.008 bbb 0.20 0.008 ccc 0.08 0.003 ddd 0.08 0.003 Tolerances of Form and Position 53 11090BS-ATARM-22-Oct-13 Figure 12-4. 64-lead QFN Package Mechanical Drawing 54 SAM3S8/SD8 Summary 11090BS-ATARM-22-Oct-13 SAM3S8/SD8 Summary 13. Ordering Information Table 13-1. Ordering Codes for SAM3S8/SD8 Devices Ordering Code MRL Flash (Kbytes) Package (Kbytes) Package Type Temperature Operating Range ATSAM3S8CA-AU A 512 QFP100 Green Industrial -40C to 85C ATSAM3S8CA-CU A 512 BGA100 Green Industrial -40C to 85C ATSAM3S8BA-AU A 512 QFP64 Green Industrial -40C to 85C ATSAM3S8BA-MU A 512 QFN64 Green Industrial -40C to 85C ATSAM3SD8CA-AU A 512 QFP100 Green Industrial -40C to 85C ATSAM3SD8CA-CU A 512 BGA100 Green Industrial -40C to 85C ATSAM3SD8BA-AU A 512 QFP64 Green Industrial -40C to 85C ATSAM3SD8BA-MU A 512 QFN64 Green Industrial -40C to 85C 55 11090BS-ATARM-22-Oct-13 Revision History In the information that follows, the most recent version of the document is referenced first. Change Request Ref. Doc. Rev Comments 11090BS Corrected Figure 12-3 "64-lead LQFP Package Mechanical Drawing" and inserted Table 12-1 "64-lead LQFP Package Dimensions (in mm)". Doc. Rev Comments 11090AS First issue 56 9389 Change Request Ref. SAM3S8/SD8 Summary 11090BS-ATARM-22-Oct-13 Atmel Corporation 1600 Technology Drive Atmel Asia Limited Unit 01-5 & 16, 19F Atmel Munich GmbH Business Campus Atmel Japan G.K. 16F Shin-Osaki Kangyo Bldg San Jose, CA 95110 BEA Tower, Millennium City 5 Parkring 4 1-6-4 Osaki, Shinagawa-ku USA 418 Kwun Tong Road D-85748 Garching b. Munich Tokyo 141-0032 Tel: (+1) (408) 441-0311 Kwun Tong, Kowloon GERMANY JAPAN Fax: (+1) (408) 487-2600 HONG KONG Tel: (+49) 89-31970-0 Tel: (+81) (3) 6417-0300 www.atmel.com Tel: (+852) 2245-6100 Fax: (+49) 89-3194621 Fax: (+81) (3) 6417-0370 Fax: (+852) 2722-1369 Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN THE ATMEL TERMS AND CONDITIONS OF SALES LOCATED ON THE ATMEL WEBSITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS AND PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and products descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life. (c) 2013 Atmel Corporation. All rights reserved. Atmel(R), Atmel logo and combinations thereof, QTouch (R), DataFlash(R), SAM-BA (R) and others are registered trademarks or trademarks of Atmel Corporation or its subsidiaries.Windows(R) and others, are registered trademarks or trademarks of Microsoft Corporation in the US and/or other countries. ARM (R), Cortex (R), Thumb(R)-2 and others are registered trademarks or trademarks of ARM Ltd. Other terms and product names may be trademarks of others. 11090BS-ATARM-22-Oct-13 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Atmel: ATSAM3SD8CA-AU ATSAM3S8BA-MU ATSAM3SD8BA-AUR ATSAM3SD8CA-CUR ATSAM3S8CA-CUR ATSAM3S8BA-AUR ATSAM3S8CA-AUR ATSAM3SD8CA-AUR