BZW04-7V0B-E3/73 - Vishay [General Semiconductor]

BZW04-5V8 thru BZW04-376

www.vishay.com Vishay General Semiconductor

Revision: 08-May-12 1Document Number: 88316

For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

TransZorb® Transient Voltage Suppressors

DEVICES FOR BI-DIRECTION APPLICATIONS

For bi-directional types, use B suffix (e.g.

BZW04P-6V4B).

Electrical characteristics apply in both directions.

FEATURES

• Glass passivated chip junction

• Available in uni-directional and bi-directional

• 400 W peak pulse power capability with a

10/1000 μs waveform, repetitive rate

(duty cycle): 0.01 %

• Excellent clamping capability

• Very fast response time

• Low incremental surge resistance

• Solder dip 275 °C max. 10 s, per JESD 22-B106

• AEC-Q101 qualified

• Material categorization: For definitions of compliance

please see www.vishay.com/doc?99912

TYPICAL APPLICATIONS

Use in sensitive electronics protection against voltage

transients induced by inductive load switching and lighting

on ICs, MOSFET, signal lines of sensor units for consumer,

computer, industrial, and telecommunication.

MECHANICAL DATA

Case: DO-204AL, molded epoxy over passivated chip

Molding compound meets UL 94 V-0 flammability rating

Base P/N-E3 - RoHS-compliant, commercial grade

Base P/NHE3 - RoHS-compliant, AEC-Q101 qualified

Terminals: Matte tin plated leads, solderable per

J-STD-002 and JESD22-B102

E3 suffix meets JESD 201 class 1A whisker test, HE3 suffix

meets JESD 201 class 2 whisker test

Note

BZW04-213(B) to BZW04-376(B) for commercial grade only

Polarity: For uni-directional types the color band denotes

cathode end, no marking on bi-directional types

Notes

(1) Non-repetitive current pulse, per fig. 3 and derated above TA = 25 °C per fig. 2

(2) Measured on 8.3 ms single half sine-wave or equivalent square wave, duty cycle = 4 pulses per minute maximum

(3) VF = 3.5 V for BZW04P(-)188 and below; VF = 5.0 V for BZW04P(-)213 and above

PRIMARY CHARACTERISTICS

VWM 5.8 V to 376 V

PPPM 400 W

PD1.5 W

IFSM (uni-directional only) 40 A

TJ max. 175 °C

DO-204AL (DO-41)

MAXIMUM RATINGS AND THERMAL CHARACTERISTICS (TA = 25 °C unles otherwise noted)

PARAMETER SYMBOL LIMIT UNIT

Peak pulse power dissipation with a 10/1000 μs waveform (1) (fig. 1) PPPM 400 W

Peak pulse current with a 10/1000 μs waveform (1) IPPM See next

table A

Power dissipation on infinite heatsink at TL = 75 °C (fig. 5) PD1.5 W

Peak forward surge current, 8.3 ms single half sine-wave uni-directional only (2) IFSM 40 A

Maximum instantaneous forward voltage at 25 A for uni-directional only (3) VF 3.5/5.0 V

Operating junction and storage temperature range TJ, TSTG - 55 to + 175 °C

BZW04-5V8 thru BZW04-376

www.vishay.com Vishay General Semiconductor

Revision: 08-May-12 2Document Number: 88316

For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Notes

(1) Pulse test: tp  50 ms

(2) Surge current waveform per fig. 3 and derated per fig. 2

(3) All terms and symbols are consistent with ANSI/IEEE C62.35

(4) For bi-directional types having VWM of 10 V and less, the ID limit is doubled

ELECTRICAL CHARACTERISTICS (TA = 25 °C unless otherwise noted)

PART NUMBER

BREAKDOWN

VOLTAGE

AT I

(1)

(V)

TEST

CURRENT

(

STAND-

OFF

VOLTAGE

(V)

MAXIMUM

REVERSE

LEAKAGE

AT V

(4)

( A)

MAXIMUM

PEAK

PULSE

CURRENT

PPM

(2)

(A)

MAXIMUM

CLAMPING

VOLTAGE

AT I

PPM

(V)

MAXIMUM

TEMPERATURE

COEFFICIENT

(%/°C)

UNI-DIRECTIONAL BI-DIRECTIONAL MIN. MAX.

BZW04-5V8 BZW04-5V8B 6.45 7.14 10.0 5.80 1000 38.0 10.5 0.057

BZW04-6V4 BZW04-6V4B 7.13 7.88 10.0 6.40 500 35.4 11.3 0.061

BZW04-7V0 BZW04-7V0B 7.79 8.61 10.0 7.02 200 33.0 12.1 0.065

BZW04-7V8 BZW04-7V8B 8.65 9.55 1.0 7.78 50 30.0 13.4 0.073

BZW04-8V5 BZW04-8V5B 9.50 10.5 1.0 8.55 10 27.6 14.5 0.075

BZW04-9V4 BZW04-9V4B 10.5 11.6 1.0 9.4 5.0 25.7 15.6 0.075

BZW04-10 BZW04-10B 11.4 12.6 1.0 10.2 1.0 24.0 16.7 0.078

BZW04-11 BZW04-11B 12.4 13.7 1.0 11.1 1.0 22.0 18.2 0.081

BZW04-13 BZW04-13B 14.3 15.8 1.0 12.8 1.0 19.0 21.2 0.084

BZW04-14 BZW04-14B 15.2 16.8 1.0 13.6 1.0 17.8 22.5 0.086

BZW04-15 BZW04-15B 17.1 18.9 1.0 15.3 1.0 16.0 25.2 0.088

BZW04-17 BZW04-17B 19.0 21.0 1.0 17.1 1.0 14.5 27.7 0.090

BZW04-19 BZW04-19B 20.9 23.1 1.0 18.8 1.0 13.0 30.6 0.092

BZW04-20 BZW04-20B 22.8 25.2 1.0 20.5 1.0 12.0 33.2 0.094

BZW04-23 BZW04-23B 25.7 28.4 1.0 23.1 1.0 10.7 37.5 0.096

BZW04-26 BZW04-26B 28.5 31.5 1.0 25.6 1.0 9.6 41.5 0.097

BZW04-28 BZW04-28B 31.4 34.7 1.0 28.2 1.0 8.8 45.7 0.098

BZW04-31 BZW04-31B 34.2 37.8 1.0 30.8 1.0 8.0 49.9 0.099

BZW04-33 BZW04-33B 37.1 41.0 1.0 33.3 1.0 7.4 53.9 0.100

BZW04-37 BZW04-37B 40.9 45.2 1.0 36.8 1.0 6.7 59.3 0.101

BZW04-40 BZW04-40B 44.7 49.4 1.0 40.2 1.0 6.2 64.8 0.101

BZW04-44 BZW04-44B 48.5 53.6 1.0 43.6 1.0 5.7 70.1 0.102

BZW04-48 BZW04-48B 53.2 58.8 1.0 47.8 1.0 5.2 77.0 0.103

BZW04-53 BZW04-53B 58.9 65.1 1.0 53.0 1.0 4.7 85.0 0.104

BZW04-58 BZW04-58B 64.6 71.4 1.0 58.1 1.0 4.3 92.0 0.104

BZW04-64 BZW04-64B 71.3 78.8 1.0 64.1 1.0 3.9 103 0.105

BZW04-70 BZW04-70B 77.9 86.1 1.0 70.1 1.0 3.5 113 0.105

BZW04-78 BZW04-78B 86.5 95.5 1.0 78.0 1.0 3.2 125 0.105

BZW04-85 BZW04-85B 95.0 105 1.0 85.5 1.0 2.9 137 0.106

BZW04-94 BZW04-94B 105 116 1.0 94.0 1.0 2.6 152 0.107

BZW04-102 BZW04-102B 114 126 1.0 102 1.0 2.4 165 0.107

BZW04-110 BZW04-110B 124 137 1.0 111 1.0 2.2 179 0.107

BZW04-128 BZW04-128B 143 158 1.0 128 1.0 2.0 207 0.108

BZW04-136 BZW04-136B 152 168 1.0 136 1.0 1.8 219 0.108

BZW04-145 BZW04-145B 161 179 1.0 145 1.0 1.7 234 0.108

BZW04-154 BZW04-154B 171 189 1.0 154 1.0 1.6 246 0.108

BZW04-171 BZW04-171B 190 210 1.0 171 1.0 1.5 274 0.108

BZW04-188 BZW04-188B 209 231 1.0 188 1.0 1.4 301 0.108

BZW04-213 BZW04-213B 237 263 1.0 213 1.0 1.2 344 0.110

BZW04-239 BZW04-239B 266 294 1.0 239 1.0 1.1 384 0.110

BZW04-256 BZW04-256B 285 315 1.0 256 1.0 1.0 414 0.110

BZW04-273 BZW04-273B 304 336 1.0 273 1.0 0.90 438 0.110

BZW04-299 BZW04-299B 332 368 1.0 299 1.0 0.80 482 0.110

BZW04-342 BZW04-342B 380 420 1.0 342 1.0 0.75 548 0.110

BZW04-376 BZW04-376B 418 462 1.0 376 1.0 0.67 603 0.110

BZW04-5V8 thru BZW04-376

www.vishay.com Vishay General Semiconductor

Revision: 08-May-12 3Document Number: 88316

For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Note

(1) AEC Q101 qualified

RATINGS AND CHARACTERISTICS CURVES (TA = 25 °C unless otherwise noted)

Fig. 1 - Peak Pulse Power Rating Curve

Fig. 2 - Pulse Power or Current vs. Initial Junction Temperature

Fig. 3 - Pulse Waveform

Fig. 4 - Typical Junction Capacitance

Fig. 5 - Power Derating Curve

Fig. 6 - Max. Non-Repetitive Forward Surge Current

Uni-Directional Only

ORDERING INFORMATION (Example)

PREFERRED P/N UNIT WEIGHT (g) PREFERRED PACKAGE CODE BASE QUANTITY DELIVERY MODE

BZW0410-E3/54 0.350 54 550 13" diameter paper tape and reel

BZW0410HE3/54 (1) 0.350 54 550 13" diameter paper tape and reel

100

0.1

Non-Repetitive Pulse

Waveform shown in Fig. 3

= 25 °C

0.1 1 10 100 1000 10 000

PPM

- Peak Pulse Power (kW)

- Pulse Width (µs)

100

0 25 50 75 100 125 150 175 200

Peak Pulse Power (P

) or Current (I

)

Derating in Percentage (%)

- Initial Temperature (°C)

01.0 2.0 3.0 4.0

100

150

t - Time (ms)

IPPM - Peak Pulse Current, % IRSM

= 10 µs

Peak Value

PPM

Half Value -

PPM

10/1000 µs Waveform

as defined by R.E.A.

= 25 °C

Pulse Width (t

)

is defined as the Point

where the Peak Current

Decays to 50 % of I

PPM

100

1000

10 000

1 10 100 1000

Measured at

Zero Bias

Measured at Stand-Off

Voltage V

= 25 °C

f = 1.0 MHz

sig

= 50 mVp-p

- Junction Capacitance (pF)

- Breakdown Voltage (V)

- Power Dissipation (%)

- Lead Temperature (°C)

60 Hz

Resistive or

Inductive Load

100

0 25 50 75 100 125 150 175 200

L = 0.375" (9.5 mm)

Lead Lengths

1 10 100

100

Number of Cycles at 60 Hz

Peak Forward Surge Current (A)

TJ = TJ Max.

8.3 ms Single Half Sine-Wave

BZW04-5V8 thru BZW04-376

www.vishay.com Vishay General Semiconductor

Revision: 08-May-12 4Document Number: 88316

For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

PACKAGE OUTLINE DIMENSIONS in inches (millimeters)

DO-204AL (DO-41)

1.0 (25.4)

MIN.

1.0 (25.4)

MIN.

0.205 (5.2)

0.160 (4.1)

0.107 (2.7)

0.080 (2.0)

DIA.

0.034 (0.86)

0.028 (0.71)

DIA.

Legal Disclaimer Notice

www.vishay.com Vishay

Revision: 12-Mar-12 1Document Number: 91000

Disclaimer

ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE

RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.

Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,

“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other

disclosure relating to any product.

Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or

the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all

liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,

consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular

purpose, non-infringement and merchantability.

Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical

requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements

about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular

product with the properties described in the product specification is suitable for use in a particular application. Parameters

provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All

operating parameters, including typical parameters, must be validated for each customer application by the customer’s

technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,

including but not limited to the warranty expressed therein.

Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining

applications or for any other application in which the failure of the Vishay product could result in personal injury or death.

Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk and agree

to fully indemnify and hold Vishay and its distributors harmless from and against any and all claims, liabilities, expenses and

damages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that Vishay

or its distributor was negligent regarding the design or manufacture of the part. Please contact authorized Vishay personnel to

obtain written terms and conditions regarding products designed for such applications.

No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by

any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.

Material Category Policy

Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the

definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council

of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment

(EEE) - recast, unless otherwise specified as non-compliant.

Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that

all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.