PCA9527 3-channel bidirectional bus extender for HDMI, I2C-bus and SMBus Rev. 01 -- 29 June 2009 Product data sheet 1. General description The PCA9527 is a 3-channel bidirectional open-drain bus buffer for Display Data Control (DDC) clock, data and Consumer Electronic Control (CEC) for HDMI application. The device has two power supply pins to allow voltage level shift from 2.7 V to 5 V, and a rise time accelerator on port A of each DDC clock and data for driving longer cable (up to 18 meters or 1400 pF reliably without violating the bus rise time). The 5 V tolerant CEC channel is internally connected to VCC(B) and has no rise time accelerator. The CEC channel can be used as an interrupt or reset. While retaining all the operating modes and features of the I2C-bus system during the level shift, it also permits extension of the I2C-bus by providing bidirectional buffering for data (SDA), clock (SCL), and CEC. Using the PCA9527 enables the system designer to isolate bus capacitance to meet HDMI DDC version 1.3 distance specification. The SDAx and SCLx pins are overvoltage tolerant and are high-impedance when the PCA9527 is unpowered. The port B drivers (SDAB, SCLB, CECB) with static level offset behave much like the drivers on the PCA9515 device, while the SDAA and SCLA drivers integrate the rise time accelerator, sink more current and eliminate the static offset voltage. The CECA driver has the same current and static offset voltage features as the SDAA and SCLA, but it does not have the rise time accelerator and is powered and referenced to VCC(B). This results in a LOW on the port B translating into a nearly 0 V LOW on port A, providing zero offset. The static level offset design of the port B I/O drivers prevent them from being connected to another device that has rise time accelerator including the PCA9507 (port B), PCA9510, PCA9511, PCA9512, PCA9513, PCA9514, PCA9515, PCA9516A, PCA9517 (port B), or PCA9518A. Port A of two or more PCA9527s can be connected together, however, to allow a star topography with port A on the common bus, and port A can be connected directly to any other buffer with static or dynamic offset voltage. Multiple PCA9527s can be connected in series, port A to port B, with no build-up in offset voltage with only time of flight delays to consider. Rise time accelerators on the SDAA and SCLA pins are turned on when input threshold is above 0.3VCC(A). The PCA9527 SDA and SCL drivers are not enabled unless VCC(A) and VCC(B) are above 2.7 V. The EN pin can also be used to turn the drivers on and off under system control. Caution should be observed to only change the state of the enable pin when the bus is idle. The output pull-down on the port B internal buffer LOW is set for approximately 0.5 V, while the input threshold of the internal buffer is set about 70 mV lower (0.43 V). When the port B I/O is driven LOW internally, the LOW is not recognized as a LOW by the input. This prevents a lock-up condition from occurring. PCA9527 NXP Semiconductors 3-channel bidirectional bus extender for HDMI, I2C-bus and SMBus 2. Features n 3-channel, bidirectional buffer isolates capacitance allowing 1400 pF on port A and 400 pF on port B n Exceeds 18 meters (above the maximum distance for HDMI DDC) n Rise time accelerator and normal I/O on port A (no accelerator for CEC) n Static level offset on port B n Voltage level translation from 2.7 V to 5.5 V n CEC is 5 V tolerant, powered by VCC(B) n Upgrade replacement over PCA9507 and PCA9517A for cable application n I2C-bus, SMBus and DDC-bus compatible n Active HIGH buffer enable input n Open-drain input/outputs n Lock-up free operation n Supports arbitration and clock stretching across the repeater n Accommodates Standard-mode and Fast-mode I2C-bus devices and multiple masters n Powered-off high-impedance I2C-bus pins n Port A operating supply voltage range of 2.7 V to 5.5 V n Port B operating supply voltage range of 2.7 V to 3.6 V n 5 V tolerant I2C-bus and enable pins n 0 Hz to 400 kHz clock frequency (the maximum system operating frequency may be less than 400 kHz because of the delays added by the repeater) n ESD protection exceeds 8000 V HBM per JESD22-A114, 500 V MM per JESD22-A115, and 1000 V CDM per JESD22-C101 n Latch-up testing is done to JEDEC Standard JESD78 which exceeds 100 mA n Package offered: TSSOP10 3. Ordering information Table 1. Ordering information Type number PCA9527DP [1] Topside mark Package Name Description Version 9527 TSSOP10[1] plastic thin shrink small outline package; 10 leads; body width 3 mm SOT552-1 Also known as MSOP10. PCA9527_1 Product data sheet (c) NXP B.V. 2009. All rights reserved. Rev. 01 -- 29 June 2009 2 of 22 PCA9527 NXP Semiconductors 3-channel bidirectional bus extender for HDMI, I2C-bus and SMBus 4. Functional diagram VCC(B) VCC(A) VCC(A) DYNAMIC PULL-UP SCLA SCLB VCC(A) DYNAMIC PULL-UP SDAA SDAB CECA CECB VCC(B) 100 k PCA9527 EN 002aad970 GND Fig 1. Functional diagram of PCA9527 5. Pinning information 5.1 Pinning VCC(A) 1 SCLA 2 SDAA 3 CECA GND 10 VCC(B) 9 SCLB 8 SDAB 4 7 CECB 5 6 EN PCA9527DP 002aad969 Fig 2. Pin configuration for TSSOP10 5.2 Pin description Table 2. Pin description Symbol Pin Description VCC(A) 1 port A supply voltage (2.7 V to 5.5 V) SCLA 2 serial clock port A bus with rise time accelerator for DDC line or cable, 5 V tolerant SDAA 3 serial data port A bus with rise time accelerator for DDC line or cable, 5 V tolerant CECA 4 serial data with normal I/O powered by VCC(B), 5 V tolerant PCA9527_1 Product data sheet (c) NXP B.V. 2009. All rights reserved. Rev. 01 -- 29 June 2009 3 of 22 PCA9527 NXP Semiconductors 3-channel bidirectional bus extender for HDMI, I2C-bus and SMBus Table 2. Pin description ...continued Symbol Pin Description GND 5 supply ground (0 V) EN 6 active HIGH buffer enable input CECB 7 serial data with static level offset, powered by VCC(B), 5 V tolerant SDAB 8 serial data port B bus with static level offset, 5 V tolerant SCLB 9 serial clock port B bus with static level offset, 5 V tolerant VCC(B) 10 port B supply voltage (2.7 V to 3.6 V) 6. Functional description Refer to Figure 1 "Functional diagram of PCA9527". The PCA9527 consists of 3 channels of bidirectional open-drain I/Os specifically designed to support up-translation/down-translation between low voltages (as low as 2.7 V) and a 3.3 V or 5 V I2C-bus and SMBus. The device contains a rise time accelerator, specifically on port A of the SCLA and SDAA that enables the device to drive a long cable or a heavier capacitive load for DDC, I2C-bus and SMBus applications. With dual supply rails, the device translates from voltage ranges 2.7 V to 5.5 V down to a voltage as low as 2.7 V without degradation of system performance. Unlike the SDAA and SCLA, the CECA is powered by the VCC(B) and does not have a rise time accelerator, but is similar in that its port A has normal I/O and port B static level offset. All I/Os are overvoltage tolerant to 5.5 V even when the device is un-powered (VCC(B) and/or VCC(A) = 0 V). The PCA9527 includes a power-up circuit that keeps the SDA and SCL output drivers turned off until VCC(A) and VCC(B) rise above 2.7 V. The CECA output drivers are turned OFF until VCC(B) rises above 2.7 V. VCC(A) and VCC(B) can be applied in any sequence at power-up. VCC(B) port B 0.3VCC(B) 0.5 V 0.4 V 0V VCC(A) port A 0.7VCC(A) 0.3VCC(A) 0V 002aad435 Fig 3. Port A and port B I/O levels When port B falls first and goes below 0.3VCC(B) the port A driver is turned on and port A pulls down to 0 V. As port A falls below 0.3VCC(A) the port B pulls down to about 0.5 V. The external port B driver must drive the port B to a LOW that is 0.4 V or else it is not possible to know who is driving the port A LOW. The PCA9527 direction control assumes that port A is controlling the part unless port B falls below 0.4 V. When the port B voltage is 0.4 V the port A driver of the PCA9527 is on and holds port A down to nearly 0 V. As the port B voltage rises because the external driver turns off, the port B voltage rises up to ~0.5 V because port A is LOW; once port B rises to ~0.5 V the port A pull-down driver turns off. Then port A rises with a rise time determined by the RC of port A when it PCA9527_1 Product data sheet (c) NXP B.V. 2009. All rights reserved. Rev. 01 -- 29 June 2009 4 of 22 PCA9527 NXP Semiconductors 3-channel bidirectional bus extender for HDMI, I2C-bus and SMBus crosses the port A threshold ~0.3VCC(A) the port B driver is turned off and the rising edge accelerator is turned on, which causes a faster rising edge until it reaches the turn-off point for the rising edge accelerator ~0.7VCC(A). Then it continues to rise at the slower rate determined by the RC of port A. When the port B driver turns off, port B rises with the RC of port B. VCC(A) powers the 0.3VCC(A) reference for SCLA and SDAA as well as the port A power good detect circuit. VCC(B) powers the rest of the chip including the port B I/Os, the CEC I/Os, and the support functions. Figure 3 illustrates the threshold and I/O levels for port A and port B. 6.1 Enable The EN pin is active HIGH with an internal ~100 k pull-up to VCC(B) and allows the user to select when the buffer is active. The enable pin puts the PCA9527 in a power-down state when it is disabled, so that there is a recovery delay and a lower power-down power. This can be used to isolate the line when the HDMI DDC transmitter or receiver is not ready, or from a badly behaved slave on power-up until after the system power-up reset. It should never change state during an I2C-bus operation because disabling during a bus operation will hang the bus and enabling part way through a bus cycle could confuse the I2C-bus parts being enabled. The enable pin should only change state when the global bus and the buffer port are in an idle state to prevent system failures. 6.2 Rise time accelerators PCA9527 has rise time accelerators on port A of SCL and SDA only; the CECA pin does not have a rise time accelerator. During port A positive bus transitions a current source is switched on to quickly slew the SDAA and SCLA lines HIGH once the input level of 0.3VCC(A) is exceeded for the PCA9527 and turns off as the 0.7VCC(A) voltage is approached. 6.3 Resistor pull-up value selection 6.3.1 Port A (SDAA and SCLA) SDAA and SCLA are open-drain I/O that have rise time accelerators and strong pull-down. When the inputs transition above 0.3VCC(A), the rise time accelerator activates and boosts the pull-up current during rising edge to meet the I2C-bus rise time specification when the device drives a long cable or heavier capacitance load. The strong pull-down enables the output to drive to nearly zero voltage for logic LOW. The selection for pull-up resistors are defined in the HDMI DDC specification shown in Table 3. For HDMI transmitter applications like digital video player, recorder, or set-top box, the pull-up resistor is in the range of 1.5 k to 2 k. For HDMI receiver applications like in LCD TV or video card, the pull-up resistor is 47 k on the SCLA line, and there is no pull-up on the SDAA line. Please refer to Table 3, Figure 6 and Figure 7 for more details. Figure 4 shows the port A pull-up resistor values (in k) versus capacitance load (in nF) for 5 V supply voltage complied with 1 s rise time per I2C-bus Standard-mode specification. The graph contrasts a shaded and unshaded region. Any resistor value chosen within the unshaded region would comply with 1 s rise time, while any value chosen in the shaded region would not. PCA9527_1 Product data sheet (c) NXP B.V. 2009. All rights reserved. Rev. 01 -- 29 June 2009 5 of 22 PCA9527 NXP Semiconductors 3-channel bidirectional bus extender for HDMI, I2C-bus and SMBus Table 3. HDMI DDC pull-up resistors specification Pin Where Minimum Maximum SDAA at the source (DVD/STB) 1.5 k 2.0 k at the sink (LCD TV) - - SCLA at the source (DVD/STB) 1.5 k 2.0 k 47 k 10 % at the sink (LCD TV) 002aad620 10.5 RPU (k) 8.5 6.5 does not comply with 1 s rise time 4.5 complies with 1 s rise time 2.5 0.5 0 1.0 2.0 3.0 4.0 CL (nF) rise time = 1 s; VCC(A) = 5 V Fig 4. SDAA/SCLA line pull-up resistor versus load capacitance 6.3.2 Port A (CECA) CECA does not have a rise time accelerator, but has a standard open-drain I/O. In addition to incurring no offset voltage, it has edge rate control and a lower capacitance than those of standard discrete MOSFET, and isolates the input/output capacitance. It is designed for a lower speed channel for consumer electronic control (less than 10 kHz) or general purpose interrupt or reset over long cable. CECA does not have internal pull-up. The pull-up resistor is calculated using standard I2C-bus pull-up resistor formula, as shown in Section 6.3.3 "Port B (SDAB, SCLB, CECB)". PCA9527_1 Product data sheet (c) NXP B.V. 2009. All rights reserved. Rev. 01 -- 29 June 2009 6 of 22 PCA9527 NXP Semiconductors 3-channel bidirectional bus extender for HDMI, I2C-bus and SMBus 6.3.3 Port B (SDAB, SCLB, CECB) SDAB and SCLB are standard I2C-bus with static level offset that has no rise time accelerator. The static level offset produces an output LOW of 0.5 V (typical) at 6 mA. As with the standard I2C-bus system, pull-up resistors are required to provide the logic HIGH levels. The size of these pull-up resistors depends on the system requirement, and should meet the current sinking capability of the device that drives the buffer, as well as that of the buffer. The minimum and maximum pull-up resistors are determined and the pull-up resistor's value is chosen to be within the minimum and maximum range. Using Equation 1, calculate the minimum pull-up resistor value: V pu ( max ) - 0.4 V R PU ( min ) = ---------------------------------------I OL ( max ) (1) Where: RPU(min) is the minimum pull-up resistor value for the open-drain SCLB and SDAB. Vpu(max) is the maximum supply rail of the pull-up resistor and should not exceed 5.5 V. 0.4 V is the maximum VOL of the device that drives the buffer on logic LOW. IOL(max) at VOL = 0.4 V is the maximum sink current of the device that drives the buffer on logic LOW. The maximum pull-up resistor should also be sized such that the RC time constant meets the standard I2C-bus rise time, which is 1 s for Standard-mode (100 kHz) or 300 ns for Fast-mode (400 kHz). DDC bus complies with the I2C-bus Standard-mode and operates below 100 kHz, and maximum rise time is 1 s using a simplified RC equation. Using Equation 2, calculate the maximum pull-up resistor value: R PU ( max ) x C L ( max ) = 1.2 x t r (2) Where: RPU(max) is the maximum allowable pull-up resistor on the SCLB and SDAB in order to meet the I2C-bus rise time specification. CL(max) is the maximum allowable capacitance load (include the capacitance of driver, the line, and the buffer) in order to meet the rise time specification. tr is the rise time specified as 1 s (for bus speed 100 kHz or lower) and 300 ns (for bus speed 400 kHz or lower). The chosen pull-up resistor RPU is: RPU(min) RPU RPU(max). PCA9527_1 Product data sheet (c) NXP B.V. 2009. All rights reserved. Rev. 01 -- 29 June 2009 7 of 22 PCA9527 NXP Semiconductors 3-channel bidirectional bus extender for HDMI, I2C-bus and SMBus 7. Application design-in information A typical application is shown in Figure 5. In this example, the system master is running on a 3.3 V I2C-bus while the slave is connected to a 5 V bus. Both buses run at 400 kHz. Master devices can be placed on either bus. HDMI DDC applications for DVD/R and LCD TV are shown in Figure 6 and Figure 7, respectively. In these applications the HDMI transmitter or receiver is 3.3 V, while the DDC line is 5 V, PCA9527 behaves like a voltage level shift, a buffer and long cable bus extender to ensure signal integrity for accessing the EDID on the DDC line. 3.3 V 10 k 10 k 5V 10 k 10 k VCC(B) SDAB SDAA SDA SCL SCLB SCLA SCL INTR or RESET CECB CECA INTR or RESET SLAVE 400 kHz PCA9527 EN bus B bus A 002aad971 Typical application 3.3 V 5V 0.1 F 10 k (optional) 10 k 10 k 10 k 0.1 F VCC(B) 2.7 k VCC(A) PCA9527 HDMI TRANSMITTER 10 k SDA BUS MASTER 400 kHz Fig 5. 10 k VCC(A) SDAB SCLB CECB EN SDAA SCLA CECA 1.5 k to 2.0 k (2x) 22 22 GND HDMI cable DDC line LCD TV (sink) PCA9507 PCA9512A PCA9515 PCA9517 PCA9527 DVD/R or STB 002aad972 Fig 6. Source or DVD/R, STB application PCA9527_1 Product data sheet (c) NXP B.V. 2009. All rights reserved. Rev. 01 -- 29 June 2009 8 of 22 PCA9527 NXP Semiconductors 3-channel bidirectional bus extender for HDMI, I2C-bus and SMBus 3.3 V 5V 0.1 F 10 k (optional) 10 k 10 k 10 k 0.1 F VCC(B) 10 k VCC(A) PCA9527 SDAB SCLB CECB EN HDMI RECEIVER 47 k SDAA SCLA CECA 22 22 GND HDMI cable DDC line DVD (source) PCA9507 PCA9512A PCA9515 PCA9517 PCA9527 LCD TV 002aad973 Fig 7. Sink or LCD TV application According to Figure 5, when port A of the PCA9527 is pulled LOW by a driver on the I2C-bus, a comparator detects the falling edge when it goes below 0.3VCC(A) and causes the internal driver on port B to turn on, causing port B to pull down to about 0.5 V. When port B of the PCA9527 falls, first a CMOS hysteresis type input detects the falling edge and causes the internal driver on port A to turn on and pull the port A pin down to ground. In order to illustrate what would be seen in a typical application, refer to Figure 11 and Figure 12. If the bus master in Figure 5 were to write to the slave through the PCA9527, waveforms shown in Figure 11 would be observed on the A bus. This looks like a normal I2C-bus transmission except that the HIGH level may be as low as 2.7 V, and the turn on and turn off of the acknowledge signals are slightly delayed. The master drives the B bus to ground or lets it float to VCC(B) as it sends data to the slave at the falling edge of the 8th clock, master releases SDAB on the B bus and slave pulls SDAA on the A bus to ground, causing the PCA9527 to pull SDAB on the B bus to 0.5 V. At the falling edge of the 9th clock, the master again drives the B bus and slave releases the A bus. Multiple PCA9527 port A sides can be connected in a star configuration (Figure 8), allowing all nodes to communicate with each other. Multiple PCA9527s can be connected in series (Figure 9) as long as port A is connected to port B. I2C-bus slave devices can be connected to any of the bus segments. The number of devices that can be connected in series is limited by repeater delay/time-of-flight considerations on the maximum bus speed requirements. PCA9527_1 Product data sheet (c) NXP B.V. 2009. All rights reserved. Rev. 01 -- 29 June 2009 9 of 22 PCA9527 NXP Semiconductors 3-channel bidirectional bus extender for HDMI, I2C-bus and SMBus VCC(A) VCC(B) 10 k 10 k 10 k VCC(A) 10 k SDAA SCLA CECA SDA SCL BUS MASTER INT or RESET 10 k 10 k VCC(B) SDAB SCLB CECB SDA SCL INT or RESET PCA9527 SLAVE 400 kHz EN 10 k VCC(A) SDAA SCLA CECA 10 k 10 k VCC(B) SDAB SCLB CECB SDA SCL INT or RESET PCA9527 SLAVE 400 kHz EN 10 k VCC(A) SDAA SCLA CECA 10 k 10 k VCC(B) SDAB SCLB CECB SDA SCL INT or RESET PCA9527 SLAVE 400 kHz EN 002aad974 Fig 8. Typical star application VCC 10 k 10 k 10 k 10 k 10 k 10 k SDA SCL BUS MASTER 10 k INT or RESET SDAA SCLA CECA SDAB SCLB CECB PCA9527 EN 10 k 10 k 10 k INT or RESET SDAA SCLA CECA SDAB SCLB CECB PCA9527 INT or RESET EN 10 k 10 k SDAA SCLA CECA SDAB SCLB CECB PCA9527 EN SDA SCL INT or RESET SLAVE 400 kHz 002aad975 Fig 9. Typical series application PCA9527_1 Product data sheet (c) NXP B.V. 2009. All rights reserved. Rev. 01 -- 29 June 2009 10 of 22 PCA9527 NXP Semiconductors 3-channel bidirectional bus extender for HDMI, I2C-bus and SMBus CARD 1 VCC(A) CARD 2 RPU VCCB RPU 10 k VCC(A) 10 k 10 k (optional) VCC(B) 75 75 75 SDAA SCLA CECA SDAB SCLB CECB GND INT or RESET MASTER OR SLAVE EN 002aad976 Fig 10. Typical application of PCA9527 driving a short cable 9th clock pulse acknowledge SCLA SDAA 002aad431 Fig 11. Bus A (2.7 V to 5.5 V bus) waveform 9th clock pulse acknowledge SCLB SDAB VOL of PCA9527 002aad977 VOL of slave Fig 12. Bus B (2.7 V to 5.5 V) waveform PCA9527_1 Product data sheet (c) NXP B.V. 2009. All rights reserved. Rev. 01 -- 29 June 2009 11 of 22 PCA9527 NXP Semiconductors 3-channel bidirectional bus extender for HDMI, I2C-bus and SMBus 8. Limiting values Table 4. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Symbol Parameter Conditions VCC(B) supply voltage port B VCC(A) supply voltage port A VI/O voltage on an input/output pin port B; port A; EN II/O input/output current port A; port B ISS ground supply current Ptot total power dissipation Tstg storage temperature Tamb ambient temperature Tj junction temperature operating in free air Min Max Unit -0.5 +7 V -0.5 +7 V -0.5 +7 V - 50 mA - 100 mA - 100 mW -55 +125 C -40 +85 C - +125 C 9. Static characteristics Table 5. Static characteristics VCC = 2.7 V to 5.5 V; GND = 0 V; Tamb = -40 C to +85 C; unless otherwise specified. Symbol Parameter Conditions Min Typ Max Unit 2.7 - 3.6 V Supplies VCC(B) supply voltage port B VCC(A) supply voltage port A Istb standby current ICCH(A) [1] 2.7 - 5.5 V - 40 60 A port A HIGH-level supply current - 0.5 0.8 mA ICCL(A) port A LOW-level supply current A port channels LOW; VCC(B) = 3.6 V; VCC(A) = 5.5 V; B port open - 1.1 1.7 mA Istb standby current - 40 60 A ICCH(B) port B HIGH-level supply current all inputs HIGH; VCC(B) = 3.6 V; SDAA = SCLA = VCC(A); SDAB, SCLB, CECn, EN = VCC(B) VCC(A) = 5 V - 0.8 1.2 mA VCC(A) = 0 V - 0.5 0.7 mA VCC(A) = 5 V - 1.4 2.2 mA VCC(A) = 0 V - 0.7 1.1 mA - 1.4 2.2 mA ICCL(B) ICC(B)c inputs VCC or GND on pin VCC(A); EN = 0 V inputs VCC or GND on pin VCC(B); EN = 0 V port B LOW-level supply current B port channels LOW; VCC(B) = 3.6 V; A port open contention port B supply current VCC(B) = 3.6 V; SDAB = SCLB = 0.2 V PCA9527_1 Product data sheet (c) NXP B.V. 2009. All rights reserved. Rev. 01 -- 29 June 2009 12 of 22 PCA9527 NXP Semiconductors 3-channel bidirectional bus extender for HDMI, I2C-bus and SMBus Table 5. Static characteristics ...continued VCC = 2.7 V to 5.5 V; GND = 0 V; Tamb = -40 C to +85 C; unless otherwise specified. Symbol Parameter Conditions Min Typ Max Unit 5.5 V Input and output SDAB, SCLB and CECB VIH HIGH-level input voltage VIL LOW-level input voltage VILc contention LOW-level input voltage VIK input clamping voltage 0.7VCC(B) -0.5 - +0.3VCC(B) V -0.5 0.4 - V II = -18 mA - - -1.2 V [2] ILI input leakage current VI = 5.5 V - - 1 A IIL LOW-level input current VI = 0.2 V - - 10 A VOL LOW-level output voltage IOL = 100 A or 6 mA 0.47 0.52 0.6 V VOL-VILc difference between LOW-level output and LOW-level input voltage contention guaranteed by design - - 70 mV Cio input/output capacitance VI = 3 V or 0 V; VCC = 3.3 V - 6 8 pF VI = 3 V or 0 V; VCC = 0 V - 6 8 pF 0.7VCC(A) - 5.5 V -0.5 - +0.3VCC(A) V II = -18 mA - - -1.2 V Input and output SDAA, SCLA VIH HIGH-level input voltage VIL LOW-level input voltage VIK input clamping voltage [3] ILI input leakage current VCC = VI = 5.5 V - - 1 A IIL LOW-level input current VI = 0.2 V - - 10 A VOL LOW-level output voltage IOL = 6 mA - 0.1 0.2 V Cio input/output capacitance VI = 3 V or 0 V; VCC = 3.3 V - 6 8 pF Itrt(pu) transient boosted pull-up current SCLA, SDAA only; VCC(A) = 4.5 V; slew rate = 1.25 V/s VI = 3 V or 0 V; VCC = 0 V - 6 8 pF - 6 - mA 0.7VCC(B) - 5.5 V -0.5 - +0.3VCC(B) V Input and output CECA VIH HIGH-level input voltage VIL LOW-level input voltage VIK input clamping voltage II = -18 mA - - -1.2 V ILI input leakage current VCC = VI = 5.5 V - - 1 A IIL LOW-level input current VI = 0.2 V - - 10 A VOL LOW-level output voltage IOL = 6 mA - 0.1 0.2 V Cio input/output capacitance VI = 3 V or 0 V; VCC = 3.3 V - 6 8 pF VI = 3 V or 0 V; VCC = 0 V - 6 8 pF - +0.3VCC(B) V [3] Enable VIL LOW-level input voltage -0.5 VIH HIGH-level input voltage 0.7VCC(B) - IIL(EN) LOW-level input current on pin EN VI = 0.2 V, EN pin only; VCC = 3.6 V - ILI input leakage current VI = VCC Ci input capacitance VI = 3.0 V or 0 V PCA9527_1 Product data sheet 5.5 V -10 -30 A -1 - +1 A - 2 5 pF (c) NXP B.V. 2009. All rights reserved. Rev. 01 -- 29 June 2009 13 of 22 PCA9527 NXP Semiconductors 3-channel bidirectional bus extender for HDMI, I2C-bus and SMBus [1] LOW-level supply voltage. [2] VIL specification is for the first LOW level seen by the SDAB/SCLB/CECB lines. VILc is for the second and subsequent LOW levels seen by the SDAB/SCLB/CECB lines to retain a valid LOW level the static level must be less than VILc. [3] VIL for port A with envelope noise must be below 0.3VCC(A) for stable performance. 10. Dynamic characteristics Table 6. Dynamic characteristics VCC = 2.7 V to 5.5 V; GND = 0 V; Tamb = -40 C to +85 C; unless otherwise specified.[1][2] Symbol Parameter Conditions tPLH LOW to HIGH propagation delay port B to port A; Figure 15 tPHL HIGH to LOW propagation delay port B to port A; Figure 13 tTLH LOW to HIGH output transition time port A; Figure 13 tTHL HIGH to LOW output transition time port A; Figure 13 [4] Min Typ[3] Max Unit 70 115 350 ns 40 75 180 ns 20 155 280 ns 20 60 100 ns 125 175 310 ns 130 220 330 ns tPLH LOW to HIGH propagation delay port A to port B; Figure 14 [5] tPHL HIGH to LOW propagation delay port A to port B; Figure 14 [5] tTLH LOW to HIGH output transition time port B; Figure 14 80 130 260 ns tTHL HIGH to LOW output transition time port B; Figure 14 20 45 100 ns tPLH LOW to HIGH propagation delay CECA; Figure 16 40 110 250 ns tPHL HIGH to LOW propagation delay CECA; Figure 16 40 80 180 ns tTLH LOW to HIGH output transition time CECA; Figure 16 80 150 260 ns tTHL HIGH to LOW output transition time CECA; Figure 16 20 60 100 ns tsu set-up time EN HIGH before START condition [6] 200 - - s th hold time EN HIGH after STOP condition [6] 200 - - ns VCC(A) power-down to active; EN HIGH and VCC(B) on; VCC(A) ramping up [7] 200 - - s VCC(B) power-down to active; EN HIGH and VCC(A) on; VCC(B) ramping up [8] 200 - - s trec(pd-act) recovery time from power-down to active [1] Times are specified with loads of 1.35 k pull-up resistance and 57 pF load capacitance on port B, and 450 pull-up resistance and 57 pF load capacitance on port A. Different load resistance and capacitance will alter the RC time constant, thereby changing the propagation delay and transition times. [2] Pull-up voltages are VCC(A) on port A and VCC(B) on port B. [3] Typical values were measured with VCC(A) = 3.3 V at Tamb = 25 C, unless otherwise noted. [4] The tPLH delay data from port B to port A is measured at 0.5 V on port B to 0.3VCC(A) on port A. [5] The proportional delay data from port A to port B is measured at 0.3VCC(A) on port A to 0.3VCC(B) on port B. [6] The enable pin, EN, should only change state when the global bus and the repeater port are in an idle state. [7] If the VCC(A) ramp up is fast, then the trec(pd-act) time must be allowed before the inputs are switched. If the supply ramp up is slow, the channels may be connected even before the final supply voltage is reached. [8] If the VCC(B) ramp up is fast, then the trec(pd-act) time must be allowed before the inputs are switched. If the supply ramp up is slow, the channels may be connected even before the final supply voltage is reached. PCA9527_1 Product data sheet (c) NXP B.V. 2009. All rights reserved. Rev. 01 -- 29 June 2009 14 of 22 PCA9527 NXP Semiconductors 3-channel bidirectional bus extender for HDMI, I2C-bus and SMBus 10.1 AC waveforms VCC(B) input VCC(A) 0.3VCC(B) input 0.1 V tPHL 80 % output 0.3VCC(A) 0.3VCC(A) 20 % 80 % 20 % tTHL tTLH 0.3VCC(A) tPHL VCC(A) 80 % output VOL tPLH 0.3VCC(B) 0.3VCC(B) 20 % 20 % tTHL 80 % tTLH 002aae449 Fig 13. tPHL propagation delay and transition times; SCLB/SDAB to SCLA/SDAA VCC(B) 002aad433 Fig 14. Propagation delay and transition times; SCLA/SDAA to SCLB/SDAB VCC(B) input SDAB, SCLB, CECB output SCLA, SDAA, CECA input 0.3VCC(B) 0.3VCC(B) tPHL 0.5 V 80 % output 0.3VCC(A)(1) tPLH 0.3VCC(B) 0.3VCC(B) 20 % 20 % tTHL tPLH 80 % VCC(B) tTLH 002aae450 002aae460 (1) CECA output has 0.3VCC(B) reference. Fig 15. tPLH propagation delay; B inputs to A inputs Fig 16. Propagation delay and transition times; CEC in to CEC out 11. Test information VCC(B) VCC(B) VCC(A) PULSE GENERATOR VI RL VO DUT CL RT 002aab649 RL = load resistor; 1.35 k on port B (2.7 V to 5 V) and 1.5 k on port A (5.0 V). CL = load capacitance includes jig and probe capacitance; 57 pF. RT = termination resistance should be equal to Zo of pulse generators. Fig 17. Test circuit for open-drain outputs PCA9527_1 Product data sheet (c) NXP B.V. 2009. All rights reserved. Rev. 01 -- 29 June 2009 15 of 22 PCA9527 NXP Semiconductors 3-channel bidirectional bus extender for HDMI, I2C-bus and SMBus 12. Package outline TSSOP10: plastic thin shrink small outline package; 10 leads; body width 3 mm D E SOT552-1 A X c y HE v M A Z 6 10 A2 (A3) A1 A pin 1 index Lp L 1 5 detail X e w M bp 0 2.5 5 mm scale DIMENSIONS (mm are the original dimensions) UNIT A max. A1 A2 A3 bp c D (1) E (2) e HE L Lp v w y Z (1) mm 1.1 0.15 0.05 0.95 0.80 0.25 0.30 0.15 0.23 0.15 3.1 2.9 3.1 2.9 0.5 5.0 4.8 0.95 0.7 0.4 0.1 0.1 0.1 0.67 0.34 6 0 Notes 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. 2. Plastic or metal protrusions of 0.25 mm maximum per side are not included. OUTLINE VERSION REFERENCES IEC JEDEC JEITA EUROPEAN PROJECTION ISSUE DATE 99-07-29 03-02-18 SOT552-1 Fig 18. Package outline SOT552-1 (TSSOP10) PCA9527_1 Product data sheet (c) NXP B.V. 2009. All rights reserved. Rev. 01 -- 29 June 2009 16 of 22 PCA9527 NXP Semiconductors 3-channel bidirectional bus extender for HDMI, I2C-bus and SMBus 13. Soldering of SMD packages This text provides a very brief insight into a complex technology. A more in-depth account of soldering ICs can be found in Application Note AN10365 "Surface mount reflow soldering description". 13.1 Introduction to soldering Soldering is one of the most common methods through which packages are attached to Printed Circuit Boards (PCBs), to form electrical circuits. The soldered joint provides both the mechanical and the electrical connection. There is no single soldering method that is ideal for all IC packages. Wave soldering is often preferred when through-hole and Surface Mount Devices (SMDs) are mixed on one printed wiring board; however, it is not suitable for fine pitch SMDs. Reflow soldering is ideal for the small pitches and high densities that come with increased miniaturization. 13.2 Wave and reflow soldering Wave soldering is a joining technology in which the joints are made by solder coming from a standing wave of liquid solder. The wave soldering process is suitable for the following: * Through-hole components * Leaded or leadless SMDs, which are glued to the surface of the printed circuit board Not all SMDs can be wave soldered. Packages with solder balls, and some leadless packages which have solder lands underneath the body, cannot be wave soldered. Also, leaded SMDs with leads having a pitch smaller than ~0.6 mm cannot be wave soldered, due to an increased probability of bridging. The reflow soldering process involves applying solder paste to a board, followed by component placement and exposure to a temperature profile. Leaded packages, packages with solder balls, and leadless packages are all reflow solderable. Key characteristics in both wave and reflow soldering are: * * * * * * Board specifications, including the board finish, solder masks and vias Package footprints, including solder thieves and orientation The moisture sensitivity level of the packages Package placement Inspection and repair Lead-free soldering versus SnPb soldering 13.3 Wave soldering Key characteristics in wave soldering are: * Process issues, such as application of adhesive and flux, clinching of leads, board transport, the solder wave parameters, and the time during which components are exposed to the wave * Solder bath specifications, including temperature and impurities PCA9527_1 Product data sheet (c) NXP B.V. 2009. All rights reserved. Rev. 01 -- 29 June 2009 17 of 22 PCA9527 NXP Semiconductors 3-channel bidirectional bus extender for HDMI, I2C-bus and SMBus 13.4 Reflow soldering Key characteristics in reflow soldering are: * Lead-free versus SnPb soldering; note that a lead-free reflow process usually leads to higher minimum peak temperatures (see Figure 19) than a SnPb process, thus reducing the process window * Solder paste printing issues including smearing, release, and adjusting the process window for a mix of large and small components on one board * Reflow temperature profile; this profile includes preheat, reflow (in which the board is heated to the peak temperature) and cooling down. It is imperative that the peak temperature is high enough for the solder to make reliable solder joints (a solder paste characteristic). In addition, the peak temperature must be low enough that the packages and/or boards are not damaged. The peak temperature of the package depends on package thickness and volume and is classified in accordance with Table 7 and 8 Table 7. SnPb eutectic process (from J-STD-020C) Package thickness (mm) Package reflow temperature (C) Volume (mm3) < 350 350 < 2.5 235 220 2.5 220 220 Table 8. Lead-free process (from J-STD-020C) Package thickness (mm) Package reflow temperature (C) Volume (mm3) < 350 350 to 2000 > 2000 < 1.6 260 260 260 1.6 to 2.5 260 250 245 > 2.5 250 245 245 Moisture sensitivity precautions, as indicated on the packing, must be respected at all times. Studies have shown that small packages reach higher temperatures during reflow soldering, see Figure 19. PCA9527_1 Product data sheet (c) NXP B.V. 2009. All rights reserved. Rev. 01 -- 29 June 2009 18 of 22 PCA9527 NXP Semiconductors 3-channel bidirectional bus extender for HDMI, I2C-bus and SMBus maximum peak temperature = MSL limit, damage level temperature minimum peak temperature = minimum soldering temperature peak temperature time 001aac844 MSL: Moisture Sensitivity Level Fig 19. Temperature profiles for large and small components For further information on temperature profiles, refer to Application Note AN10365 "Surface mount reflow soldering description". 14. Abbreviations Table 9. Abbreviations Acronym Description CDM Charged-Device Model CEC Consumer Electronic Control CMOS Complementary Metal-Oxide Semiconductor DDC Display Data Channel DVD Digital Video Disc DUT Device Under Test EDID Extended Display Identification Data ESD ElectroStatic Discharge HBM Human Body Model HDMI High-Definition Multimedia Interface I2C-bus Inter Integrated Circuit bus I/O Input/Output LCD Liquid Crystal Display MM Machine Model MOSFET Metal-Oxide Semiconductor Field-Effect Transistor RC Resistor-Capacitor network SMBus System Management Bus STB Set-Top Box PCA9527_1 Product data sheet (c) NXP B.V. 2009. All rights reserved. Rev. 01 -- 29 June 2009 19 of 22 PCA9527 NXP Semiconductors 3-channel bidirectional bus extender for HDMI, I2C-bus and SMBus 15. Revision history Table 10. Revision history Document ID Release date Data sheet status Change notice Supersedes PCA9527_1 20090629 Product data sheet - - PCA9527_1 Product data sheet (c) NXP B.V. 2009. All rights reserved. Rev. 01 -- 29 June 2009 20 of 22 PCA9527 NXP Semiconductors 3-channel bidirectional bus extender for HDMI, I2C-bus and SMBus 16. Legal information 16.1 Data sheet status Document status[1][2] Product status[3] Definition Objective [short] data sheet Development This document contains data from the objective specification for product development. Preliminary [short] data sheet Qualification This document contains data from the preliminary specification. Product [short] data sheet Production This document contains the product specification. [1] Please consult the most recently issued document before initiating or completing a design. [2] The term `short data sheet' is explained in section "Definitions". [3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com. 16.2 Definitions Draft -- The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet -- A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. 16.3 Disclaimers General -- Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. Right to make changes -- NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. Suitability for use -- NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in medical, military, aircraft, space or life support equipment, nor in applications where failure or malfunction of an NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors accepts no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer's own risk. Applications -- Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Limiting values -- Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) may cause permanent damage to the device. Limiting values are stress ratings only and operation of the device at these or any other conditions above those given in the Characteristics sections of this document is not implied. Exposure to limiting values for extended periods may affect device reliability. Terms and conditions of sale -- NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms, including those pertaining to warranty, intellectual property rights infringement and limitation of liability, unless explicitly otherwise agreed to in writing by NXP Semiconductors. In case of any inconsistency or conflict between information in this document and such terms and conditions, the latter will prevail. No offer to sell or license -- Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. Export control -- This document as well as the item(s) described herein may be subject to export control regulations. Export might require a prior authorization from national authorities. 16.4 Licenses Purchase of NXP ICs with HDMI technology Use of an NXP IC with HDMI technology in equipment that complies with the HDMI standard requires a license from HDMI Licensing LLC, 1060 E. Arques Avenue Suite 100, Sunnyvale CA 94085, USA, e-mail: admin@hdmi.org. 16.5 Trademarks Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. I2C-bus -- logo is a trademark of NXP B.V. 17. Contact information For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com PCA9527_1 Product data sheet (c) NXP B.V. 2009. All rights reserved. Rev. 01 -- 29 June 2009 21 of 22 PCA9527 NXP Semiconductors 3-channel bidirectional bus extender for HDMI, I2C-bus and SMBus 18. Contents 1 2 3 4 5 5.1 5.2 6 6.1 6.2 6.3 6.3.1 6.3.2 6.3.3 7 8 9 10 10.1 11 12 13 13.1 13.2 13.3 13.4 14 15 16 16.1 16.2 16.3 16.4 16.5 17 18 General description . . . . . . . . . . . . . . . . . . . . . . 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Ordering information . . . . . . . . . . . . . . . . . . . . . 2 Functional diagram . . . . . . . . . . . . . . . . . . . . . . 3 Pinning information . . . . . . . . . . . . . . . . . . . . . . 3 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 3 Functional description . . . . . . . . . . . . . . . . . . . 4 Enable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Rise time accelerators . . . . . . . . . . . . . . . . . . . 5 Resistor pull-up value selection . . . . . . . . . . . . 5 Port A (SDAA and SCLA) . . . . . . . . . . . . . . . . . 5 Port A (CECA) . . . . . . . . . . . . . . . . . . . . . . . . . 6 Port B (SDAB, SCLB, CECB) . . . . . . . . . . . . . . 7 Application design-in information . . . . . . . . . . 8 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . 12 Static characteristics. . . . . . . . . . . . . . . . . . . . 12 Dynamic characteristics . . . . . . . . . . . . . . . . . 14 AC waveforms. . . . . . . . . . . . . . . . . . . . . . . . . 15 Test information . . . . . . . . . . . . . . . . . . . . . . . . 15 Package outline . . . . . . . . . . . . . . . . . . . . . . . . 16 Soldering of SMD packages . . . . . . . . . . . . . . 17 Introduction to soldering . . . . . . . . . . . . . . . . . 17 Wave and reflow soldering . . . . . . . . . . . . . . . 17 Wave soldering . . . . . . . . . . . . . . . . . . . . . . . . 17 Reflow soldering . . . . . . . . . . . . . . . . . . . . . . . 18 Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Revision history . . . . . . . . . . . . . . . . . . . . . . . . 20 Legal information. . . . . . . . . . . . . . . . . . . . . . . 21 Data sheet status . . . . . . . . . . . . . . . . . . . . . . 21 Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Licenses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Contact information. . . . . . . . . . . . . . . . . . . . . 21 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Please be aware that important notices concerning this document and the product(s) described herein, have been included in section `Legal information'. (c) NXP B.V. 2009. All rights reserved. For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com Date of release: 29 June 2009 Document identifier: PCA9527_1