GS832118/32/36AD-xxxV 333 MHz-150 MHz 2.5 V or 3.3 V VDD 2.5 V or 3.3 V I/O 2M x 18, 1M x 32, 1M x 36 36Mb Sync Burst SRAMs 165-Bump BGA Commercial Temp Industrial Temp Features * IEEE 1149.1 JTAG-compatible Boundary Scan * 1.8 V or 2.5 V core power supply * 1.8 V or 2.5 V I/O supply * LBO pin for Linear or Interleaved Burst mode * Internal input resistors on mode pins allow floating mode pins * Byte Write (BW) and/or Global Write (GW) operation * Internal self-timed write cycle * Automatic power-down for portable applications * JEDEC-standard 165-bump BGA package * RoHS-compliant 165-bump BGA package available Functional Description Flow Through/Pipeline Reads The function of the Data Output register can be controlled by the user via the FT mode pin (Pin 14). Holding the FT mode pin low places the RAM in Flow Through mode, causing output data to bypass the Data Output Register. Holding FT high places the RAM in Pipeline mode, activating the risingedge-triggered Data Output Register. SCD Pipelined Reads The GS832118/32/36AD-xxxV is a SCD (Single Cycle Deselect) pipelined synchronous SRAM. DCD (Dual Cycle Deselect) versions are also available. SCD SRAMs pipeline deselect commands one stage less than read commands. SCD RAMs begin turning off their outputs immediately after the deselect command has been captured in the input registers. Applications The GS832118/32/36AD-xxxV is a 37,748,736-bit high performance synchronous SRAM with a 2-bit burst address counter. Although of a type originally developed for Level 2 Cache applications supporting high performance CPUs, the device now finds application in synchronous SRAM applications, ranging from DSP main store to networking chip set support. Byte Write and Global Write Byte write operation is performed by using Byte Write enable (BW) input combined with one or more individual byte write signals (Bx). In addition, Global Write (GW) is available for writing all bytes at one time, regardless of the Byte Write control inputs. Controls Addresses, data I/Os, chip enable (E1), address burst control inputs (ADSP, ADSC, ADV) and write control inputs (Bx, BW, GW) are synchronous and are controlled by a positiveedge-triggered clock input (CK). Output enable (G) and power down control (ZZ) are asynchronous inputs. Burst cycles can be initiated with either ADSP or ADSC inputs. In Burst mode, subsequent burst addresses are generated internally and are controlled by ADV. The burst address counter may be configured to count in either linear or interleave order with the Linear Burst Order (LBO) input. The Burst function need not be used. New addresses can be loaded on every cycle with no degradation of chip performance. Core and Interface Voltages The GS832118/32/36AD-xxxV operates on a 1.8 V or 2.5 V power supply. All inputs are 1.8 V or 2.5 V compatible. Separate output power (VDDQ) pins are used to decouple output noise from the internal circuits and are 1.8 V or 2.5 V compatible. Sleep Mode Low power (Sleep mode) is attained through the assertion (High) of the ZZ signal, or by stopping the clock (CK). Memory data is retained during Sleep mode. Parameter Synopsis Pipeline 3-1-1-1 Flow Through 2-1-1-1 Rev: 1.03 8/2013 tKQ tCycle Curr (x18) Curr (x32/x36) tKQ tCycle Curr (x18) Curr (x32/x36) -333 3.0 3.0 -250 3.0 4.0 -200 3.0 5.0 -150 3.8 6.7 Unit ns ns 365 425 5.0 5.0 270 315 290 345 5.5 5.5 245 280 250 290 6.5 6.5 210 250 215 240 7.5 7.5 200 230 mA mA ns ns mA mA 1/30 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2011, GSI Technology GS832118/32/36AD-xxxV 165 Bump BGA--x18 Commom I/O--Top View (Package D) 1 2 3 4 5 6 7 8 9 10 11 A NC A E1 BB NC E3 BW ADSC ADV A A A B NC A E2 NC BA CK GW G ADSP A NC B C NC NC VDDQ VSS VSS VSS VSS VSS VDDQ NC DQPA C D NC DQB VDDQ VDD VSS VSS VSS VDD VDDQ NC DQA D E NC DQB VDDQ VDD VSS VSS VSS VDD VDDQ NC DQA E F NC DQB VDDQ VDD VSS VSS VSS VDD VDDQ NC DQA F G NC DQB VDDQ VDD VSS VSS VSS VDD VDDQ NC DQA G H FT MCL NC VDD VSS VSS VSS VDD NC NC ZZ H J DQB NC VDDQ VDD VSS VSS VSS VDD VDDQ DQA NC J K DQB NC VDDQ VDD VSS VSS VSS VDD VDDQ DQA NC K L DQB NC VDDQ VDD VSS VSS VSS VDD VDDQ DQA NC L M DQB NC VDDQ VDD VSS VSS VSS VDD VDDQ DQA NC M N DQPB NC VDDQ VSS NC A NC VSS VDDQ NC NC N P NC NC A A TDI A1 TDO A A A A P R LBO A19 A A TMS A0 TCK A A A A R 11 x 15 Bump BGA--13 mm x 15 mm Body--1.0 mm Bump Pitch Rev: 1.03 8/2013 2/30 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2011, GSI Technology GS832118/32/36AD-xxxV 165 Bump BGA--x32 Common I/O--Top View (Package D) 1 2 3 4 5 6 7 8 9 10 11 A NC A E1 BC BB E3 BW ADSC ADV A NC A B NC A E2 BD BA CK GW G ADSP A NC B C NC NC VDDQ VSS VSS VSS VSS VSS VDDQ NC NC C D DQC DQC VDDQ VDD VSS VSS VSS VDD VDDQ DQB DQB D E DQC DQC VDDQ VDD VSS VSS VSS VDD VDDQ DQB DQB E F DQC DQC VDDQ VDD VSS VSS VSS VDD VDDQ DQB DQB F G DQC DQC VDDQ VDD VSS VSS VSS VDD VDDQ DQB DQB G H FT MCL NC VDD VSS VSS VSS VDD NC NC ZZ H J DQD DQD VDDQ VDD VSS VSS VSS VDD VDDQ DQA DQA J K DQD DQD VDDQ VDD VSS VSS VSS VDD VDDQ DQA DQA K L DQD DQD VDDQ VDD VSS VSS VSS VDD VDDQ DQA DQA L M DQD DQD VDDQ VDD VSS VSS VSS VDD VDDQ DQA DQA M N NC NC VDDQ VSS NC A NC VSS VDDQ NC NC N P NC NC A A TDI A1 TDO A A A A P R LBO A A A TMS A0 TCK A A A A R 11 x 15 Bump BGA--13 mm x 15 mm Body--1.0 mm Bump Pitch Rev: 1.03 8/2013 3/30 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2011, GSI Technology GS832118/32/36AD-xxxV 165 Bump BGA--x36 Common I/O--Top View (Package D) 1 2 3 4 5 6 7 8 9 10 11 A NC A E1 BC BB E3 BW ADSC ADV A NC A B NC A E2 BD BA CK GW G ADSP A NC B C DQPC NC VDDQ VSS VSS VSS VSS VSS VDDQ NC DQPB C D DQC DQC VDDQ VDD VSS VSS VSS VDD VDDQ DQB DQB D E DQC DQC VDDQ VDD VSS VSS VSS VDD VDDQ DQB DQB E F DQC DQC VDDQ VDD VSS VSS VSS VDD VDDQ DQB DQB F G DQC DQC VDDQ VDD VSS VSS VSS VDD VDDQ DQB DQB G H FT MCL NC VDD VSS VSS VSS VDD NC NC ZZ H J DQD DQD VDDQ VDD VSS VSS VSS VDD VDDQ DQA DQA J K DQD DQD VDDQ VDD VSS VSS VSS VDD VDDQ DQA DQA K L DQD DQD VDDQ VDD VSS VSS VSS VDD VDDQ DQA DQA L M DQD DQD VDDQ VDD VSS VSS VSS VDD VDDQ DQA DQA M N DQPD NC VDDQ VSS NC A NC VSS VDDQ NC DQPA N P NC NC A A TDI A1 TDO A A A A P R LBO A A A TMS A0 TCK A A A A R 11 x 15 Bump BGA--13 mm x 15 mm Body--1.0 mm Bump Pitch Rev: 1.03 8/2013 4/30 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2011, GSI Technology GS832118/32/36AD-xxxV GS832118/32/36AD-xxxV 165-Bump BGA Pin Description Symbol Type Description A 0, A 1 I Address field LSBs and Address Counter Preset Inputs A I Address Inputs DQA DQB DQC DQD I/O Data Input and Output pins BA , BB , BC , BD I Byte Write Enable for DQA, DQB, DQC, DQD I/Os; active low CK I Clock Input Signal; active high BW I Byte Write--Writes all enabled bytes; active low GW I Global Write Enable--Writes all bytes; active low E1 I Chip Enable; active low E3 I Chip Enable; active low E2 I Chip Enable; active high G I Output Enable; active low ADV I Burst address counter advance enable; active l0w ADSC, ADSP I Address Strobe (Processor, Cache Controller); active low ZZ I Sleep mode control; active high FT I Flow Through or Pipeline mode; active low LBO I Linear Burst Order mode; active low TMS I Scan Test Mode Select TDI I Scan Test Data In TDO O Scan Test Data Out TCK I Scan Test Clock MCL -- Must Connect Low VDD I Core power supply VSS I I/O and Core Ground VDDQ I Output driver power supply NC -- No Connect Rev: 1.03 8/2013 5/30 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2011, GSI Technology GS832118/32/36AD-xxxV GS832118/32/36AD-xxxV Block Diagram Register A0-An D Q A0 A0 D0 Q0 A1 A1 D1 Q1 Counter Load A LBO ADV Memory Array CK ADSC ADSP Q D Register GW BW BA D Q Register D 36 Q BB 36 4 Register D Q D Q D Q Register Register D Q Register BC BD Register D Q Register E1 E2 E3 D Q Register D Q FT G ZZ 1 Power Down DQx1-DQx9 Control Note: Only x36 version shown for simplicity. Rev: 1.03 8/2013 6/30 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2011, GSI Technology GS832118/32/36AD-xxxV Mode Pin Functions Mode Name Pin Name Burst Order Control LBO Output Register Control FT Power Down Control ZZ State Function L Linear Burst H Interleaved Burst L Flow Through H or NC Pipeline L or NC Active H Standby, IDD = ISB Note: There is a pull-up device on the FT pin and a pull-down device on the ZZ pin , so this input pin can be unconnected and the chip will operate in the default states as specified in the above tables. Burst Counter Sequences Linear Burst Sequence Interleaved Burst Sequence A[1:0] A[1:0] A[1:0] A[1:0] A[1:0] A[1:0] A[1:0] A[1:0] 1st address 00 01 10 11 1st address 00 01 10 11 2nd address 01 10 11 00 2nd address 01 00 11 10 3rd address 10 11 00 01 3rd address 10 11 00 01 4th address 11 00 01 10 4th address 11 10 01 00 Note: The burst counter wraps to initial state on the 5th clock. Rev: 1.03 8/2013 Note: The burst counter wraps to initial state on the 5th clock. 7/30 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2011, GSI Technology GS832118/32/36AD-xxxV Byte Write Truth Table Function GW BW BA BB BC BD Notes Read H H X X X X 1 Write No Bytes H L H H H H 1 Write byte a H L L H H H 2, 3 Write byte b H L H L H H 2, 3 Write byte c H L H H L H 2, 3, 4 Write byte d H L H H H L 2, 3, 4 Write all bytes H L L L L L 2, 3, 4 Write all bytes L X X X X X Notes: 1. All byte outputs are active in read cycles regardless of the state of Byte Write Enable inputs, BA, BB, BC and/or BD. 2. Byte Write Enable inputs BA, BB, BC and/or BD may be used in any combination with BW to write single or multiple bytes. 3. All byte I/Os remain High-Z during all write operations regardless of the state of Byte Write Enable inputs. 4. Bytes "C" and "D" are only available on the x32 and x36 versions. Rev: 1.03 8/2013 8/30 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2011, GSI Technology GS832118/32/36AD-xxxV Synchronous Truth Table Operation Address Used State Diagram Key E1 E2 E3 ADSP ADSC ADV W DQ3 Deselect Cycle, Power Down None X L X H X L X X High-Z Deselect Cycle, Power Down None X L L X X L X X High-Z Deselect Cycle, Power Down None X L X H L X X X High-Z Deselect Cycle, Power Down None X L L X L X X X High-Z Deselect Cycle, Power Down None X H X X X L X X High-Z Read Cycle, Begin Burst External R L H L L X X X Q Read Cycle, Begin Burst External R L H L H L X F Q Write Cycle, Begin Burst External W L H L H L X T D Read Cycle, Continue Burst Next CR X X X H H L F Q Read Cycle, Continue Burst Next CR H X X X H L F Q Write Cycle, Continue Burst Next CW X X X H H L T D Write Cycle, Continue Burst Next CW H X X X H L T D Read Cycle, Suspend Burst Current X X X H H H F Q Read Cycle, Suspend Burst Current H X X X H H F Q Write Cycle, Suspend Burst Current X X X H H H T D Write Cycle, Suspend Burst Current H X X X H H T D Notes: 1. X = Don't Care, H = High, L = Low 2. E = T (True) if E2 = 1 and E1 = E3 = 0; E = F (False) if E2 = 0 or E1 = 1 or E3 = 1 3. W = T (True) and F (False) is defined in the Byte Write Truth Table preceding. 4. G is an asynchronous input. G can be driven high at any time to disable active output drivers. G low can only enable active drivers (shown as "Q" in the Truth Table above). 5. All input combinations shown above are tested and supported. Input combinations shown in gray boxes need not be used to accomplish basic synchronous or synchronous burst operations and may be avoided for simplicity. 6. Tying ADSP high and ADSC low allows simple non-burst synchronous operations. See BOLD items above. 7. Tying ADSP high and ADV low while using ADSC to load new addresses allows simple burst operations. See ITALIC items above. Rev: 1.03 8/2013 9/30 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2011, GSI Technology GS832118/32/36AD-xxxV Simplified State Diagram X Deselect W R Simple Burst Synchronous Operation Simple Synchronous Operation W X R R First Write First Read CR CW W X CR R R X Burst Write Burst Read X CR CW CR Notes: 1. The diagram shows only supported (tested) synchronous state transitions. The diagram presumes G is tied low. 2. The upper portion of the diagram assumes active use of only the Enable (E1) and Write (BA, BB, BC, BD, BW, and GW) control inputs, and that ADSP is tied high and ADSC is tied low. 3. The upper and lower portions of the diagram together assume active use of only the Enable, Write, and ADSC control inputs, and assumes ADSP is tied high and ADV is tied low. Rev: 1.03 8/2013 10/30 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2011, GSI Technology GS832118/32/36AD-xxxV Simplified State Diagram with G X Deselect W R W X R R First Write CR CW W CW W X First Read X CR R Burst Write R CR CW W Burst Read X CW CR Notes: 1. The diagram shows supported (tested) synchronous state transitions plus supported transitions that depend upon the use of G. 2. Use of "Dummy Reads" (Read Cycles with G High) may be used to make the transition from read cycles to write cycles without passing through a deselect cycle. Dummy read cycles increment the address counter just like normal read cycles. 3. Transitions shown in gray tone assume G has been pulsed high long enough to turn the RAM's drivers off and for incoming data to meet Data Input Set Up Time. Rev: 1.03 8/2013 11/30 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2011, GSI Technology GS832118/32/36AD-xxxV Absolute Maximum Ratings (All voltages reference to VSS) Symbol Description Value Unit VDD Voltage on VDD Pins -0.5 to 4.6 V VDDQ Voltage on VDDQ Pins -0.5 to VDD V VI/O Voltage on I/O Pins -0.5 to VDD +0.5 ( 4.6 V max.) V VIN Voltage on Other Input Pins -0.5 to VDD +0.5 ( 4.6 V max.) V IIN Input Current on Any Pin +/-20 mA IOUT Output Current on Any I/O Pin +/-20 mA PD Package Power Dissipation 1.5 W TSTG Storage Temperature -55 to 125 o TBIAS Temperature Under Bias -55 to 125 o C C Note: Permanent damage to the device may occur if the Absolute Maximum Ratings are exceeded. Operation should be restricted to Recommended Operating Conditions. Exposure to conditions exceeding the Absolute Maximum Ratings, for an extended period of time, may affect reliability of this component. Power Supply Voltage Ranges (1.8 V/2.5 V Version) Parameter Symbol Min. Typ. Max. Unit 1.8 V Supply Voltage VDD1 1.7 1.8 2.0 V 2.5 V Supply Voltage VDD2 2.3 2.5 2.7 V 1.8 V VDDQ I/O Supply Voltage VDDQ1 1.7 1.8 VDD V 2.5 V VDDQ I/O Supply Voltage VDDQ2 2.3 2.5 VDD V Parameter Symbol Min. Typ. Max. Unit VDD Input High Voltage VIH 0.6*VDD -- VDD + 0.3 V VDD Input Low Voltage VIL -0.3 -- 0.3*VDD V VDDQ2 & VDDQ1 Range Logic Levels Notes: 1. Unless otherwise noted, all performance specifications quoted are evaluated for worst case in the temperature range marked on the device. 2. VIH (max) must be met for any instantaneous value of VDD. 3. VDD needs to power-up before or at the same time as VDDQ to make sure VIH (max) is not exceeded. Rev: 1.03 8/2013 12/30 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2011, GSI Technology GS832118/32/36AD-xxxV Operating Temperature Parameter Symbol Min. Typ. Max. Unit Junction Temperature (Commercial Range Versions) TJ 0 25 85 C Junction Temperature (Industrial Range Versions)* TJ -40 25 100 C Note: * The part numbers of Industrial Temperature Range versions end with the character "I". Unless otherwise noted, all performance specifications quoted are evaluated for worst case in the temperature range marked on the device. Thermal Impedance Package Test PCB Substrate JA (C/W) Airflow = 0 m/s JA (C/W) Airflow = 1 m/s JA (C/W) Airflow = 2 m/s JB (C/W) JC (C/W) 165 BGA 4-layer 24.4 21.0 20.0 11.6 3.7 Notes: 1. Thermal Impedance data is based on a number of of samples from mulitple lots and should be viewed as a typical number. 2. Please refer to JEDEC standard JESD51-6. 3. The characteristics of the test fixture PCB influence reported thermal characteristics of the device. Be advised that a good thermal path to the PCB can result in cooling or heating of the RAM depending on PCB temperature. Undershoot Measurement and Timing Overshoot Measurement and Timing VIH 20% tKC VDD + 2.0 V VSS 50% 50% VDD VSS - 2.0 V 20% tKC VIL Note: Input Under/overshoot voltage must be -2 V > Vi < VDDn+2 V not to exceed 4.6 V maximum, with a pulse width not to exceed 20% tKC. Capacitance (TA = 25oC, f = 1 MHZ, VDD = 2.5 V) Parameter Symbol Test conditions Typ. Max. Unit Input Capacitance CIN VIN = 0 V 8 10 pF Input/Output Capacitance CI/O VOUT = 0 V 12 14 pF Note: These parameters are sample tested. Rev: 1.03 8/2013 13/30 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2011, GSI Technology GS832118/32/36AD-xxxV AC Test Conditions Parameter Conditions Input high level VDD - 0.2 V Input low level 0.2 V Input slew rate 1 V/ns Input reference level VDD/2 Output reference level VDDQ/2 Output load Fig. 1 Figure 1 Output Load 1 DQ 30pF* 50 VDDQ/2 * Distributed Test Jig Capacitance Notes: 1. Include scope and jig capacitance. 2. Test conditions as specified with output loading as shown in Fig. 1 unless otherwise noted. 3. Device is deselected as defined by the Truth Table. DC Electrical Characteristics Parameter Symbol Test Conditions Min Max Input Leakage Current (except mode pins) IIL VIN = 0 to VDD -1 uA 1 uA FT Input Current IIN VDD VIN 0 V -100 uA 100 uA Output Leakage Current IOL Output Disable, VOUT = 0 to VDD -1 uA 1 uA 1.8 V Output High Voltage VOH1 IOH = -4 mA, VDDQ = 1.7 V VDDQ - 0.4 V -- 2.5 V Output High Voltage VOH2 IOH = -8 mA, VDDQ = 2.375 V 1.7 V -- 1.8 V Output Low Voltage VOL1 IOL = 4 mA -- 0.4 V 2.5 V Output Low Voltage VOL2 IOL = 8 mA -- 0.4 V Rev: 1.03 8/2013 14/30 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2011, GSI Technology Rev: 1.03 8/2013 -- -- ZZ VDD - 0.2 V Device Deselected; All other inputs VIH or VIL Operating Current Standby Current Deselect Current 245 25 55 55 IDD IDDQ ISB ISB Flow Through Pipeline Flow Through Flow Through Pipeline IDD 100 100 330 35 IDD IDDQ Pipeline IDD 270 45 IDD IDDQ Flow Through Pipeline 120 120 75 75 265 25 350 35 290 45 375 70 -40 to 85C -333 0 to 70C 355 70 Symbol IDD IDDQ Mode Notes: 1. IDD and IDDQ apply to any combination of VDD1, VDD2, VDDQ1, and VDDQ2 operation. 2. All parameters listed are worst case scenario. (x18) Device Selected; All other inputs VIH or VIL Output open (x32/ x36) Test Conditions Parameter Operating Currents 100 100 55 55 225 20 265 25 240 40 295 50 0 to 70C 120 120 75 75 245 20 285 25 260 40 315 50 -40 to 85C -250 100 100 55 55 195 15 230 20 215 35 250 40 0 to 70C 120 120 75 75 215 15 250 20 235 35 270 40 -40 to 85C -200 100 100 55 55 185 15 200 15 200 30 210 30 0 to 70C 120 120 75 75 205 15 220 15 220 30 230 30 -40 to 85C -150 mA mA mA mA mA mA mA mA Unit GS832118/32/36AD-xxxV Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. 15/30 (c) 2011, GSI Technology GS832118/32/36AD-xxxV AC Electrical Characteristics Pipeline Flow Through Parameter Symbol Clock Cycle Time -333 -250 -200 -150 Unit Min Max Min Max Min Max Min Max tKC 3.0 -- 4.0 -- 5.0 -- 6.7 -- ns Clock to Output Valid tKQ -- 3.0 -- 3.0 -- 3.0 -- 3.8 ns Clock to Output Invalid tKQX 1.5 -- 1.5 -- 1.5 -- 1.5 -- ns Clock to Output in Low-Z tLZ1 1.5 -- 1.5 -- 1.5 -- 1.5 -- ns Setup time tS 1.0 -- 1.2 -- 1.4 -- 1.5 -- ns Hold time tH 0.1 -- 0.2 -- 0.4 -- 0.5 -- ns Clock Cycle Time tKC 5.0 -- 5.5 -- 6.5 -- 7.5 -- ns Clock to Output Valid tKQ -- 5.0 -- 5.5 -- 6.5 -- 7.5 ns Clock to Output Invalid tKQX 2.0 -- 2.0 -- 2.0 -- 2.0 -- ns Clock to Output in Low-Z tLZ1 2.0 -- 2.0 -- 2.0 -- 2.0 -- ns Setup time tS 1.3 -- 1.5 -- 1.5 -- 1.5 -- ns Hold time tH 0.3 -- 0.5 -- 0.5 -- 0.5 -- ns Clock HIGH Time tKH 1.0 -- 1.3 -- 1.3 -- 1.5 -- ns Clock LOW Time tKL 1.2 -- 1.5 -- 1.5 -- 1.7 -- ns Clock to Output in High-Z tHZ1 1.5 3.0 1.5 3.0 1.5 3.0 1.5 3.8 ns G to Output Valid tOE -- 3.0 -- 3.0 -- 3.0 -- 3.8 ns G to output in Low-Z tOLZ1 0 -- 0 -- 0 -- 0 -- ns G to output in High-Z tOHZ1 -- 3.0 -- 3.0 -- 3.0 -- 3.8 ns ZZ setup time tZZS2 5 -- 5 -- 5 -- 5 -- ns ZZ hold time tZZH2 1 -- 1 -- 1 -- 1 -- ns ZZ recovery tZZR 20 -- 20 -- 20 -- 20 -- ns Notes: 1. These parameters are sampled and are not 100% tested 2. ZZ is an asynchronous signal. However, In order to be recognized on any given clock cycle, ZZ must meet the specified setup and hold times as specified above. Rev: 1.03 8/2013 16/30 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2011, GSI Technology GS832118/32/36AD-xxxV Pipeline Mode Timing Begin Read A Cont Cont Single Read Deselect Write B Read C Read C+1 Read C+2 Read C+3 Cont Single Write tKL tKH tKC Deselect Burst Read CK ADSP tS tH ADSC initiated read ADSC tS tH ADV tS tH A0-An A B C tS GW tS tH BW tH tS Ba-Bd tS Deselected with E1 tH E1 masks ADSP E1 tS tH E2 and E3 only sampled with ADSP and ADSC E2 tS tH E3 G tS tOE DQa-DQd Rev: 1.03 8/2013 tOHZ Q(A) tKQ tH D(B) tKQX tLZ tHZ Q(C) 17/30 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. Q(C+1) Q(C+2) Q(C+3) (c) 2011, GSI Technology GS832118/32/36AD-xxxV Flow Through Mode Timing Begin Read A Cont Cont Write B Read C Read C+1 Read C+2 Read C+3 Read C Cont Deselect tKL tKH tKC CK ADSP Fixed High tS tH tS tH initiated read ADSC ADSC tS tH ADV tS tH A0-An A B C tS tH GW tS tH BW tS tH Ba-Bd tS Deselected with E1 tH E1 tS tH E2 and E3 only sampled with ADSC E2 tS tH E3 G tH tS tOE DQa-DQd Rev: 1.03 8/2013 tOHZ Q(A) D(B) tKQ tLZ tHZ tKQX Q(C) Q(C+1) Q(C+2) 18/30 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. Q(C+3) Q(C) (c) 2011, GSI Technology GS832118/32/36AD-xxxV Sleep Mode During normal operation, ZZ must be pulled low, either by the user or by its internal pull down resistor. When ZZ is pulled high, the SRAM will enter a Power Sleep mode after 2 cycles. At this time, internal state of the SRAM is preserved. When ZZ returns to low, the SRAM operates normally after ZZ recovery time. Sleep mode is a low current, power-down mode in which the device is deselected and current is reduced to ISB2. The duration of Sleep mode is dictated by the length of time the ZZ is in a High state. After entering Sleep mode, all inputs except ZZ become disabled and all outputs go to High-Z The ZZ pin is an asynchronous, active high input that causes the device to enter Sleep mode. When the ZZ pin is driven high, ISB2 is guaranteed after the time tZZI is met. Because ZZ is an asynchronous input, pending operations or operations in progress may not be properly completed if ZZ is asserted. Therefore, Sleep mode must not be initiated until valid pending operations are completed. Similarly, when exiting Sleep mode during tZZR, only a Deselect or Read commands may be applied while the SRAM is recovering from Sleep mode. Sleep Mode Timing Diagram tKH tKC tKL CK Setup Hold ADSP ADSC tZZR tZZS tZZH ZZ Application Tips Single and Dual Cycle Deselect SCD devices (like this one) force the use of "dummy read cycles" (read cycles that are launched normally but that are ended with the output drivers inactive) in a fully synchronous environment. Dummy read cycles waste performance but their use usually assures there will be no bus contention in transitions from reads to writes or between banks of RAMs. DCD SRAMs do not waste bandwidth on dummy cycles and are logically simpler to manage in a multiple bank application (wait states need not be inserted at bank address boundary crossings) but greater care must be exercised to avoid excessive bus contention. JTAG Port Operation Overview The JTAG Port on this RAM operates in a manner that is compliant with IEEE Standard 1149.1-1990, a serial boundary scan interface standard (commonly referred to as JTAG). The JTAG Port input interface levels scale with VDD. The JTAG output drivers are powered by VDDQ. Disabling the JTAG Port It is possible to use this device without utilizing the JTAG port. The port is reset at power-up and will remain inactive unless clocked. TCK, TDI, and TMS are designed with internal pull-up circuits.To assure normal operation of the RAM with the JTAG Port unused, TCK, TDI, and TMS may be left floating or tied to either VDD or VSS. TDO should be left unconnected. Rev: 1.03 8/2013 19/30 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2011, GSI Technology GS832118/32/36AD-xxxV JTAG Pin Descriptions Pin Pin Name I/O Description TCK Test Clock In Clocks all TAP events. All inputs are captured on the rising edge of TCK and all outputs propagate from the falling edge of TCK. TMS Test Mode Select In The TMS input is sampled on the rising edge of TCK. This is the command input for the TAP controller state machine. An undriven TMS input will produce the same result as a logic one input level. In The TDI input is sampled on the rising edge of TCK. This is the input side of the serial registers placed between TDI and TDO. The register placed between TDI and TDO is determined by the state of the TAP Controller state machine and the instruction that is currently loaded in the TAP Instruction Register (refer to the TAP Controller State Diagram). An undriven TDI pin will produce the same result as a logic one input level. TDI Test Data In TDO Test Data Out Output that is active depending on the state of the TAP state machine. Output changes in Out response to the falling edge of TCK. This is the output side of the serial registers placed between TDI and TDO. Note: This device does not have a TRST (TAP Reset) pin. TRST is optional in IEEE 1149.1. The Test-Logic-Reset state is entered while TMS is held high for five rising edges of TCK. The TAP Controller is also reset automaticly at power-up. JTAG Port Registers Overview The various JTAG registers, refered to as Test Access Port orTAP Registers, are selected (one at a time) via the sequences of 1s and 0s applied to TMS as TCK is strobed. Each of the TAP Registers is a serial shift register that captures serial input data on the rising edge of TCK and pushes serial data out on the next falling edge of TCK. When a register is selected, it is placed between the TDI and TDO pins. Instruction Register The Instruction Register holds the instructions that are executed by the TAP controller when it is moved into the Run, Test/Idle, or the various data register states. Instructions are 3 bits long. The Instruction Register can be loaded when it is placed between the TDI and TDO pins. The Instruction Register is automatically preloaded with the IDCODE instruction at power-up or whenever the controller is placed in Test-Logic-Reset state. Bypass Register The Bypass Register is a single bit register that can be placed between TDI and TDO. It allows serial test data to be passed through the RAM's JTAG Port to another device in the scan chain with as little delay as possible. Boundary Scan Register The Boundary Scan Register is a collection of flip flops that can be preset by the logic level found on the RAM's input or I/O pins. The flip flops are then daisy chained together so the levels found can be shifted serially out of the JTAG Port's TDO pin. The Boundary Scan Register also includes a number of place holder flip flops (always set to a logic 1). The relationship between the device pins and the bits in the Boundary Scan Register is described in the Scan Order Table following. The Boundary Scan Register, under the control of the TAP Controller, is loaded with the contents of the RAMs I/O ring when the controller is in Capture-DR state and then is placed between the TDI and TDO pins when the controller is moved to Shift-DR state. SAMPLE-Z, SAMPLE/PRELOAD and EXTEST instructions can be used to activate the Boundary Scan Register. Rev: 1.03 8/2013 20/30 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2011, GSI Technology GS832118/32/36AD-xxxV JTAG TAP Block Diagram * * * * * * * * Boundary Scan Register * * 1 * M* 0 0 Bypass Register 2 1 0 Instruction Register TDI TDO ID Code Register 31 30 29 * * ** 2 1 0 Control Signals TMS Test Access Port (TAP) Controller TCK * For the value of M, see the BSDL file, which is available at by contacting us at apps@gsitechnology.com. Identification (ID) Register The ID Register is a 32-bit register that is loaded with a device and vendor specific 32-bit code when the controller is put in Capture-DR state with the IDCODE command loaded in the Instruction Register. The code is loaded from a 32-bit on-chip ROM. It describes various attributes of the RAM as indicated below. The register is then placed between the TDI and TDO pins when the controller is moved into Shift-DR state. Bit 0 in the register is the LSB and the first to reach TDO when shifting begins. GSI Technology JEDEC Vendor ID Code Not Used Bit # Presence Register ID Register Contents 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 X 1 X Rev: 1.03 8/2013 X X X X X X X X X X X X X X X X X X 0 21/30 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. 0 0 1 1 0 1 1 0 0 1 (c) 2011, GSI Technology GS832118/32/36AD-xxxV Tap Controller Instruction Set Overview There are two classes of instructions defined in the Standard 1149.1-1990; the standard (Public) instructions, and device specific (Private) instructions. Some Public instructions are mandatory for 1149.1 compliance. Optional Public instructions must be implemented in prescribed ways. The TAP on this device may be used to monitor all input and I/O pads, and can be used to load address, data or control signals into the RAM or to preload the I/O buffers. When the TAP controller is placed in Capture-IR state the two least significant bits of the instruction register are loaded with 01. When the controller is moved to the Shift-IR state the Instruction Register is placed between TDI and TDO. In this state the desired instruction is serially loaded through the TDI input (while the previous contents are shifted out at TDO). For all instructions, the TAP executes newly loaded instructions only when the controller is moved to Update-IR state. The TAP instruction set for this device is listed in the following table. JTAG Tap Controller State Diagram 1 0 Test Logic Reset 0 Run Test Idle 1 Select DR 1 Select IR 0 0 1 1 Capture DR Capture IR 0 0 Shift DR 1 1 Shift IR 0 1 1 Exit1 DR 0 Exit1 IR 0 0 Pause DR 1 Exit2 DR 1 Update DR 1 1 0 0 Pause IR 1 Exit2 IR 0 1 0 0 Update IR 1 0 Instruction Descriptions BYPASS When the BYPASS instruction is loaded in the Instruction Register the Bypass Register is placed between TDI and TDO. This occurs when the TAP controller is moved to the Shift-DR state. This allows the board level scan path to be shortened to facilitate testing of other devices in the scan path. Rev: 1.03 8/2013 22/30 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2011, GSI Technology GS832118/32/36AD-xxxV SAMPLE/PRELOAD SAMPLE/PRELOAD is a Standard 1149.1 mandatory public instruction. When the SAMPLE / PRELOAD instruction is loaded in the Instruction Register, moving the TAP controller into the Capture-DR state loads the data in the RAMs input and I/O buffers into the Boundary Scan Register. Boundary Scan Register locations are not associated with an input or I/O pin, and are loaded with the default state identified in the Boundary Scan Chain table at the end of this section of the datasheet. Because the RAM clock is independent from the TAP Clock (TCK) it is possible for the TAP to attempt to capture the I/O ring contents while the input buffers are in transition (i.e. in a metastable state). Although allowing the TAP to sample metastable inputs will not harm the device, repeatable results cannot be expected. RAM input signals must be stabilized for long enough to meet the TAPs input data capture set-up plus hold time (tTS plus tTH). The RAMs clock inputs need not be paused for any other TAP operation except capturing the I/O ring contents into the Boundary Scan Register. Moving the controller to Shift-DR state then places the boundary scan register between the TDI and TDO pins. EXTEST EXTEST is an IEEE 1149.1 mandatory public instruction. It is to be executed whenever the instruction register is loaded with all logic 0s. The EXTEST command does not block or override the RAM's input pins; therefore, the RAM's internal state is still determined by its input pins. Typically, the Boundary Scan Register is loaded with the desired pattern of data with the SAMPLE/PRELOAD command. Then the EXTEST command is used to output the Boundary Scan Register's contents, in parallel, on the RAM's data output drivers on the falling edge of TCK when the controller is in the Update-IR state. Alternately, the Boundary Scan Register may be loaded in parallel using the EXTEST command. When the EXTEST instruction is selected, the sate of all the RAM's input and I/O pins, as well as the default values at Scan Register locations not associated with a pin, are transferred in parallel into the Boundary Scan Register on the rising edge of TCK in the Capture-DR state, the RAM's output pins drive out the value of the Boundary Scan Register location with which each output pin is associated. IDCODE The IDCODE instruction causes the ID ROM to be loaded into the ID register when the controller is in Capture-DR mode and places the ID register between the TDI and TDO pins in Shift-DR mode. The IDCODE instruction is the default instruction loaded in at power up and any time the controller is placed in the Test-Logic-Reset state. SAMPLE-Z If the SAMPLE-Z instruction is loaded in the instruction register, all RAM outputs are forced to an inactive drive state (highZ) and the Boundary Scan Register is connected between TDI and TDO when the TAP controller is moved to the Shift-DR state. RFU These instructions are Reserved for Future Use. In this device they replicate the BYPASS instruction. Rev: 1.03 8/2013 23/30 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2011, GSI Technology GS832118/32/36AD-xxxV JTAG TAP Instruction Set Summary Instruction Code Description Notes EXTEST 000 Places the Boundary Scan Register between TDI and TDO. 1 IDCODE 001 Preloads ID Register and places it between TDI and TDO. 1, 2 SAMPLE-Z 010 Captures I/O ring contents. Places the Boundary Scan Register between TDI and TDO. Forces all RAM output drivers to High-Z. 1 RFU 011 Do not use this instruction; Reserved for Future Use. Replicates BYPASS instruction. Places Bypass Register between TDI and TDO. 1 SAMPLE/ PRELOAD 100 Captures I/O ring contents. Places the Boundary Scan Register between TDI and TDO. 1 GSI 101 GSI private instruction. 1 RFU 110 Do not use this instruction; Reserved for Future Use. Replicates BYPASS instruction. Places Bypass Register between TDI and TDO. 1 BYPASS 111 Places Bypass Register between TDI and TDO. 1 Notes: 1. Instruction codes expressed in binary, MSB on left, LSB on right. 2. Default instruction automatically loaded at power-up and in test-logic-reset state. Rev: 1.03 8/2013 24/30 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2011, GSI Technology GS832118/32/36AD-xxxV JTAG Port Recommended Operating Conditions and DC Characteristics (1.8/2.5 V Version) Parameter Symbol Min. Max. Unit Notes 1.8 V Test Port Input Low Voltage VILJ1 -0.3 0.3 * VDD1 V 1 2.5 V Test Port Input Low Voltage VILJ2 -0.3 0.3 * VDD2 V 1 1.8 V Test Port Input High Voltage VIHJ1 0.6 * VDD1 VDD1 +0.3 V 1 2.5 V Test Port Input High Voltage VIHJ2 0.6 * VDD2 VDD2 +0.3 V 1 TMS, TCK and TDI Input Leakage Current IINHJ -300 1 uA 2 TMS, TCK and TDI Input Leakage Current IINLJ -1 100 uA 3 TDO Output Leakage Current IOLJ -1 1 uA 4 Test Port Output High Voltage VOHJ 1.7 -- V 5, 6 Test Port Output Low Voltage VOLJ -- 0.4 V 5, 7 Test Port Output CMOS High VOHJC VDDQ - 100 mV -- V 5, 8 Test Port Output CMOS Low VOLJC -- 100 mV V 5, 9 Notes: 1. Input Under/overshoot voltage must be -2 V < Vi < VDDn +2 V not to exceed 4.6 V maximum, with a pulse width not to exceed 20% tTKC. 2. VILJ VIN VDDn 3. 0 V VIN VILJn 4. Output Disable, VOUT = 0 to VDDn 5. The TDO output driver is served by the VDDQ supply. 6. IOHJ = -4 mA 7. IOLJ = + 4 mA 8. IOHJC = -100 uA 9. IOLJC = +100 uA JTAG Port AC Test Conditions Parameter Conditions Input high level VDD - 0.2 V Input low level 0.2 V Input slew rate 1 V/ns Input reference level VDDQ/2 Output reference level VDDQ/2 JTAG Port AC Test Load DQ 50 30pF* VDDQ/2 * Distributed Test Jig Capacitance Notes: 1. Include scope and jig capacitance. 2. Test conditions as shown unless otherwise noted. Rev: 1.03 8/2013 25/30 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2011, GSI Technology GS832118/32/36AD-xxxV JTAG Port Timing Diagram tTKC tTKH tTKL TCK tTH tTS TDI tTH tTS TMS tTKQ TDO tTH tTS Parallel SRAM input JTAG Port AC Electrical Characteristics Parameter Symbol Min Max Unit TCK Cycle Time tTKC 50 -- ns TCK Low to TDO Valid tTKQ -- 20 ns TCK High Pulse Width tTKH 20 -- ns TCK Low Pulse Width tTKL 20 -- ns TDI & TMS Set Up Time tTS 10 -- ns TDI & TMS Hold Time tTH 10 -- ns Boundary Scan (BSDL Files) For information regarding the Boundary Scan Chain, or to obtain BSDL files for this part, please contact our Applications Engineering Department at: apps@gsitechnology.com. Rev: 1.03 8/2013 26/30 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2011, GSI Technology GS832118/32/36AD-xxxV Package Dimensions--165-Bump FPBGA (Package D) A1 CORNER TOP VIEW BOTTOM VIEW O0.10 M C O0.25 M C A B O0.40~0.60 (165x) 1 2 3 4 5 6 7 8 9 10 11 A1 CORNER 11 10 9 8 7 6 5 4 3 2 1 A B C D E F G H J K L M N P R 1.0 14.0 150.05 1.0 A B C D E F G H J K L M N P R A 1.0 1.0 10.0 0.15 C B Rev: 1.03 8/2013 SEATING PLANE 0.20(4x) 0.36~0.46 1.40 MAX. C 130.05 27/30 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2011, GSI Technology GS832118/32/36AD-xxxV Ordering Information for GSI Synchronous Burst RAMs Org Part Number1 Type Voltage Option Package Speed2 (MHz/ns) TJ3 2M x 18 GS832118AD-333V Synchronous Burst 1.8 V or 2.5 V 165 BGA 333/5.0 C 2M x 18 GS832118AD-250V Synchronous Burst 1.8 V or 2.5 V 165 BGA 250/5.5 C 2M x 18 GS832118AD-200V Synchronous Burst 1.8 V or 2.5 V 165 BGA 200/6.5 C 2M x 18 GS832118AD-150V Synchronous Burst 1.8 V or 2.5 V 165 BGA 150/7.5 C 1M x 32 GS832132AD-333V Synchronous Burst 1.8 V or 2.5 V 165 BGA 333/5.0 C 1M x 32 GS832132AD-250V Synchronous Burst 1.8 V or 2.5 V 165 BGA 250/5.5 C 1M x 32 GS832132AD-200V Synchronous Burst 1.8 V or 2.5 V 165 BGA 200/6.5 C 1M x 32 GS832132AD-150V Synchronous Burst 1.8 V or 2.5 V 165 BGA 150/7.5 C 1M x 36 GS832136AD-333V Synchronous Burst 1.8 V or 2.5 V 165 BGA 333/5.0 C 1M x 36 GS832136AD-250V Synchronous Burst 1.8 V or 2.5 V 165 BGA 250/5.5 C 1M x 36 GS832136AD-200V Synchronous Burst 1.8 V or 2.5 V 165 BGA 200/6.5 C 1M x 36 GS832136AD-150V Synchronous Burst 1.8 V or 2.5 V 165 BGA 150/7.5 C 2M x 18 GS832118AD-333IV Synchronous Burst 1.8 V or 2.5 V 165 BGA 333/5.0 I 2M x 18 GS832118AD-250IV Synchronous Burst 1.8 V or 2.5 V 165 BGA 250/5.5 I 2M x 18 GS832118AD-200IV Synchronous Burst 1.8 V or 2.5 V 165 BGA 200/6.5 I 2M x 18 GS832118AD-150IV Synchronous Burst 1.8 V or 2.5 V 165 BGA 150/7.5 I 1M x 32 GS832132AD-333IV Synchronous Burst 1.8 V or 2.5 V 165 BGA 333/5.0 I 1M x 32 GS832132AD-250IV Synchronous Burst 1.8 V or 2.5 V 165 BGA 250/5.5 I 1M x 32 GS832132AD-200IV Synchronous Burst 1.8 V or 2.5 V 165 BGA 200/6.5 I 1M x 32 GS832132AD-150IV Synchronous Burst 1.8 V or 2.5 V 165 BGA 150/7.5 I 1M x 36 GS832136AD-333IV Synchronous Burst 1.8 V or 2.5 V 165 BGA 333/5.0 I 1M x 36 GS832136AD-250IV Synchronous Burst 1.8 V or 2.5 V 165 BGA 250/5.5 I 1M x 36 GS832136AD-200IV Synchronous Burst 1.8 V or 2.5 V 165 BGA 200/6.5 I 1M x 36 GS832136AD-150IV Synchronous Burst 1.8 V or 2.5 V 165 BGA 150/7.5 I 2M x 18 GS832118AGD-333V Synchronous Burst 1.8 V or 2.5 V RoHS-compliant 165 BGA 333/5.0 C 2M x 18 GS832118AGD-250V Synchronous Burst 1.8 V or 2.5 V RoHS-compliant 165 BGA 250/5.5 C 2M x 18 GS832118AGD-200V Synchronous Burst 1.8 V or 2.5 V RoHS-compliant 165 BGA 200/6.5 C 2M x 18 GS832118AGD-150V Synchronous Burst 1.8 V or 2.5 V RoHS-compliant 165 BGA 150/7.5 C 1M x 32 GS832132AGD-333V Synchronous Burst 1.8 V or 2.5 V RoHS-compliant 165 BGA 333/5.0 C 1M x 32 GS832132AGD-250V Synchronous Burst 1.8 V or 2.5 V RoHS-compliant 165 BGA 250/5.5 C 1M x 32 GS832132AGD-200V Synchronous Burst 1.8 V or 2.5 V RoHS-compliant 165 BGA 200/6.5 C Notes: 1. Customers requiring delivery in Tape and Reel should add the character "T" to the end of the part number. Example: GS832118AD-150IT. 2. The speed column indicates the cycle frequency (MHz) of the device in Pipeline mode and the latency (ns) in Flow Through mode. Each device is Pipeline/Flow Through mode-selectable by the user. 3. C = Commercial Temperature Range. I = Industrial Temperature Range. 4. GSI offers other versions this type of device in many different configurations and with a variety of different features, only some of which are covered in this data sheet. See the GSI Technology web site (www.gsitechnology.com) for a complete listing of current offerings. Rev: 1.03 8/2013 28/30 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2011, GSI Technology GS832118/32/36AD-xxxV Ordering Information for GSI Synchronous Burst RAMs Org Part Number1 Type Voltage Option Package Speed2 (MHz/ns) TJ3 1M x 32 GS832132AGD-150V Synchronous Burst 1.8 V or 2.5 V RoHS-compliant 165 BGA 150/7.5 C 1M x 36 GS832136AGD-333V Synchronous Burst 1.8 V or 2.5 V RoHS-compliant 165 BGA 333/5.0 C 1M x 36 GS832136AGD-250V Synchronous Burst 1.8 V or 2.5 V RoHS-compliant 165 BGA 250/5.5 C 1M x 36 GS832136AGD-200V Synchronous Burst 1.8 V or 2.5 V RoHS-compliant 165 BGA 200/6.5 C 1M x 36 GS832136AGD-150V Synchronous Burst 1.8 V or 2.5 V RoHS-compliant 165 BGA 150/7.5 C 2M x 18 GS832118AGD-333IV Synchronous Burst 1.8 V or 2.5 V RoHS-compliant 165 BGA 333/5.0 I 2M x 18 GS832118AGD-250IV Synchronous Burst 1.8 V or 2.5 V RoHS-compliant 165 BGA 250/5.5 I 2M x 18 GS832118AGD-200IV Synchronous Burst 1.8 V or 2.5 V RoHS-compliant 165 BGA 200/6.5 I 2M x 18 GS832118AGD-150IV Synchronous Burst 1.8 V or 2.5 V RoHS-compliant 165 BGA 150/7.5 I 1M x 32 GS832132AGD-333IV Synchronous Burst 1.8 V or 2.5 V RoHS-compliant 165 BGA 333/5.0 I 1M x 32 GS832132AGD-250IV Synchronous Burst 1.8 V or 2.5 V RoHS-compliant 165 BGA 250/5.5 I 1M x 32 GS832132AGD-200IV Synchronous Burst 1.8 V or 2.5 V RoHS-compliant 165 BGA 200/6.5 I 1M x 32 GS832132AGD-150IV Synchronous Burst 1.8 V or 2.5 V RoHS-compliant 165 BGA 150/7.5 I 1M x 36 GS832136AGD-333IV Synchronous Burst 1.8 V or 2.5 V RoHS-compliant 165 BGA 333/5.0 I 1M x 36 GS832136AGD-250IV Synchronous Burst 1.8 V or 2.5 V RoHS-compliant 165 BGA 250/5.5 I 1M x 36 GS832136AGD-200IV Synchronous Burst 1.8 V or 2.5 V RoHS-compliant 165 BGA 200/6.5 I 1M x 36 GS832136AGD-150IV Synchronous Burst 1.8 V or 2.5 V RoHS-compliant 165 BGA 150/7.5 I Notes: 1. Customers requiring delivery in Tape and Reel should add the character "T" to the end of the part number. Example: GS832118AD-150IT. 2. The speed column indicates the cycle frequency (MHz) of the device in Pipeline mode and the latency (ns) in Flow Through mode. Each device is Pipeline/Flow Through mode-selectable by the user. 3. C = Commercial Temperature Range. I = Industrial Temperature Range. 4. GSI offers other versions this type of device in many different configurations and with a variety of different features, only some of which are covered in this data sheet. See the GSI Technology web site (www.gsitechnology.com) for a complete listing of current offerings. Rev: 1.03 8/2013 29/30 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2011, GSI Technology GS832118/32/36AD-xxxV 36Mb Sync SRAM Datasheet Revision History File Name Types of Changes Format or Content Page;Revisions;Reason * Creation of new datasheet 8321xxA_V_r1 8321xxA_V_r1_01 Content * Updated Absolute Maximum Ratings * Added thermal information 8321xxA_V_r1_02 Content * Updated to reflect MP status 8321xxA_V_r1_03 Content * Updated Op current numbers * Updated tHZ, tOE, and tOHZ to 3.0 ns for 333 and 300 MHz Rev: 1.03 8/2013 30/30 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2011, GSI Technology