ISP1505ABSUM - ST-Ericsson - Datasheet.Directory

1. General description

The ISP1505 is a Universal Serial Bus (USB) high-speed host and peripheral transceiver

that is fully compliant with

Universal Serial Bus Speciﬁcation Rev. 2.0

and

UTMI+ Low Pin

Interface (ULPI) Speciﬁcation Rev. 1.1

The ISP1505 can transmit and receive USB data at high-speed (480 Mbit/s), full-speed

(12 Mbit/s) and low-speed (1.5 Mbit/s), and provides a pin-optimized, physical layer

front-end attachment to USB host, peripheral and OTG devices.

It is ideal for use in portable electronic devices, such as mobile phones, digital still

cameras, digital video cameras, Personal Digital Assistants (PDAs) and digital audio

players. It allows USB Application-Speciﬁc Integrated Circuits (ASICs), Programmable

Logic Devices (PLDs) and any system chip set to interface with the physical layer of the

USB through a 12-pin interface.

The ISP1505 can interface to the link with digital I/O voltages in the range of

1.65 V to 3.6 V.

The ISP1505 is available in HVQFN24 package.

2. Features

nFully complies with:

Universal Serial Bus Speciﬁcation Rev. 2.0

UTMI+ Low Pin Interface (ULPI) Speciﬁcation Rev. 1.1

nInterfaces to host and peripheral cores; optimized for stand-alone and embedded host

applications with an external VBUS supply; stand-alone peripheral cores, and Session

Request Protocol (SRP)-capable peripheral cores

nComplete Hi-Speed USB physical front-end solution that supports high-speed

(480 Mbit/s), full-speed (12 Mbit/s) and low-speed (1.5 Mbit/s)

uIntegrated 45 Ω±10 % high-speed termination resistors, 1.5 kΩ±5 % full-speed

device pull-up resistor, and 15 kΩ±5 % host termination resistors

uIntegrated parallel-to-serial and serial-to-parallel converters to transmit and receive

uUSB clock and data recovery to receive USB data at ±500 ppm

uInsertion of stuff bits during transmit and discarding of stuff bits during receive

uNon-Return-to-Zero Inverted (NRZI) encoding and decoding

uSupports bus reset, suspend, resume and high-speed detection handshake (chirp)

nSupports SRP for reduced power consumption

uComplete control over bus resistors

uData line and VBUS pulsing session request methods

ISP1505A; ISP1505C

ULPI Hi-Speed Universal Serial Bus host and peripheral

transceiver

Rev. 01 — 19 October 2006 Product data sheet

Product data sheet Rev. 01 — 19 October 2006 2 of 78

NXP Semiconductors ISP1505A; ISP1505C

ULPI HS USB host and peripheral transceiver

uIntegrated VBUS voltage comparators

nHighly optimized ULPI-compliant interface

u60 MHz, 8-bit interface between the core and the transceiver

uSupports both 60 MHz input clock and 60 MHz output clock conﬁgurations

uIntegrated Phase-Locked Loop (PLL) with auto-conﬁguring support for 60 MHz

input clock, or one crystal or clock frequency: 19.2 MHz (ISP1505ABS), 26 MHz

(ISP1505CBS)

uFully programmable ULPI-compliant register set

uInternal Power-On Reset (POR) circuit

nFlexible system integration and very low current consumption, optimized for portable

devices

uPower-supply input range is 3.0 V to 3.6 V

uInternal voltage regulator supplies 3.3 V and 1.8 V

uSupports external VBUS charge pump

uExternal VBUS source is controlled using the PSW_N pin; open-drain PSW_N

allows per-port or ganged power control

uFAULT input pin to monitor the external VBUS supply status

uSupports wide range interfacing I/O voltage of 1.65 V to 3.6 V; separate I/O voltage

pins minimize crosstalk

uTypical operating current of 10 mA to 48 mA, depending on the USB speed and

bus utilization

uTypical suspend current of 35 µA

nFull industrial grade operating temperature range from −40 °Cto+85°C

n4 kV ElectroStatic Discharge (ESD) protection on pins DP, DM, VBUS and GND

nAvailable in a small HVQFN24 (4 mm ×4 mm) Restriction of Hazardous Substances

(RoHS) compliant, halogen-free and lead-free package

3. Applications

nDigital still camera

nDigital TV

nDigital Video Disc (DVD) recorder

nExternal storage device, for example:

uZip drive

uMagneto-Optical (MO) drive

uOptical drive: CD-ROM, CD-RW, DVD

nMobile phone

nMP3 player

nPDA

nPrinter

nScanner

nSet-Top Box (STB)

nVideo camera

Product data sheet Rev. 01 — 19 October 2006 3 of 78

NXP Semiconductors ISP1505A; ISP1505C

ULPI HS USB host and peripheral transceiver

4. Ordering information

[1] The package marking is the ﬁrst line of text on the IC package and can be used for IC identiﬁcation.

Table 1. Ordering information

Part Package

Type number Marking Crystal or

clock

frequency

Name Description Version

ISP1505ABS 05A[1] 19.2 MHz HVQFN24 plastic thermal enhanced very thin quad ﬂat package;

no leads; 24 terminals; body 4 ×4×0.85 mm SOT616-1

ISP1505CBS 05C[1] 26 MHz HVQFN24 plastic thermal enhanced very thin quad ﬂat package;

no leads; 24 terminals; body 4 ×4×0.85 mm SOT616-1

Product data sheet Rev. 01 — 19 October 2006 4 of 78

NXP Semiconductors ISP1505A; ISP1505C

ULPI HS USB host and peripheral transceiver

5. Block diagram

Fig 1. Block diagram

MAP

ULPI

INTERFACE

CONTROLLER

USB DATA

SERIALIZER

USB DATA

DESERIALIZER

HIGH-SPEED

USB ATX

STP

DIR

NXT

DATA

[7:0]

1, 2,

17 to 20,

22, 24

004aaa587

CLOCK 21

TERMINATION

RESISTORS

VBUS

COMPARATORS

SRP CHARGE

AND DISCHARGE

RESISTORS

POWER-ON

RESET

PLL

CRYSTAL

OSCILLATOR

VOLTAGE

REGULATOR

BAND GAP

REFERENCE

VOLTAGE RREF

internal power

VCC 7

REG3V3

REG1V8

RESET_N/

PSW_N GLOBAL

RESET

GLOBAL

CLOCKS

XTAL2

XTAL1 10

VCC(I/O) 3, 23 interface voltage

VBUS/

FAULT

ISP1505

ULPI

INTERFACE

USB

CABLE

VREF

VBUS VALID EXTERNAL

DRIVE VBUS EXTERNAL

Product data sheet Rev. 01 — 19 October 2006 5 of 78

NXP Semiconductors ISP1505A; ISP1505C

ULPI HS USB host and peripheral transceiver

6. Pinning information

6.1 Pinning

6.2 Pin description

Fig 2. Pin conﬁguration HVQFN24; top view

004aaa689

ISP1505

Transparent top view

REG1V8

DIR

RREF STP

VCC(I/O) NXT

DATA0 DATA7

DATA1 DATA6

VCC

VBUS/FAULT

REG3V3

XTAL1

XTAL2

RESET_N/

PSW_N

DATA2

VCC(I/O)

DATA3

CLOCK

DATA4

DATA5

terminal 1

index area

613

514

4 15

3 16

2 17

118

Table 2. Pin description

Symbol[1][2] Pin Type[3] Description[4]

DATA1 1 I/O pin 1 of the bidirectional ULPI data bus

slew-rate controlled output (1 ns); plain input; programmable pull down

DATA0 2 I/O pin 0 of the bidirectional ULPI data bus

slew-rate controlled output (1 ns); plain input; programmable pull down

VCC(I/O) 3 P I/O supply rail

RREF 4 AI/O resistor reference

DM 5 AI/O data minus (D−) pin of the USB cable

DP 6 AI/O data plus (D+) pin of the USB cable

VCC 7 P input supply voltage or battery source

VBUS/FAULT 8 AI/O This pin has two possible functions:

VBUS (analog input and output) — VBUS pin of the USB cable.

FAULT (input) — Input pin for the external VBUS digital overcurrent or fault detector

signal.

If this pin is not used as either VBUS or FAULT, it must be tied to ground.

5 V tolerant

REG3V3 9 P 3.3 V regulator output

XTAL1 10 AI crystal oscillator or clock input

XTAL2 11 AO crystal oscillator output

Product data sheet Rev. 01 — 19 October 2006 6 of 78

NXP Semiconductors ISP1505A; ISP1505C

ULPI HS USB host and peripheral transceiver

[1] Symbol names ending with underscore N, for example, NAME_N, indicate active LOW signals.

[2] For details on external components required on each pin, see bill of materials and application diagrams in Section 16.

[3] I = input; O = output; I/O = digital input/output; AI = analog input; AO = analog output; AI/O = analog input/output; P = power or ground

pin.

[4] A detailed description of these pins can be found in Section 7.10.

RESET_N/

PSW_N 12 I/O This pin has two possible functions:

RESET_N (input) — Active LOW, asynchronous reset input.

3.3 V tolerant; plain input

PSW_N (output) — Active LOW external VBUS power switch or external charge

pump enable.

open-drain; 3.3 V tolerant

If not used, this pin must be connected to VCC(I/O).

REG1V8 13 P 1.8 V regulator output

DIR 14 O ULPI direction signal

slew-rate controlled output (1 ns)

STP 15 I ULPI stop signal

plain input; programmable pull up

NXT 16 O ULPI next signal

slew-rate controlled output (1 ns)

DATA7 17 I/O pin 7 of the bidirectional ULPI data bus

slew-rate controlled output (1 ns); plain input; programmable pull down

DATA6 18 I/O pin 6 of the bidirectional ULPI data bus

slew-rate controlled output (1 ns); plain input; programmable pull down

DATA5 19 I/O pin 5 of the bidirectional ULPI data bus

slew-rate controlled output (1 ns); plain input; programmable pull down

DATA4 20 I/O pin 4 of the bidirectional ULPI data bus

slew-rate controlled output (1 ns); plain input; programmable pull down

CLOCK 21 I/O 60 MHz clock output when a crystal is attached; requires 60 MHz clock input when

the crystal is not attached

slew-rate controlled output (1 ns); plain input

DATA3 22 I/O pin 3 of the bidirectional ULPI data bus

slew-rate controlled output (1 ns); plain input; programmable pull down

VCC(I/O) 23 P I/O supply rail

DATA2 24 I/O pin 2 of the bidirectional ULPI data bus

slew-rate controlled output (1 ns); plain input; programmable pull down

GND die pad P ground supply; down bonded to the exposed die pad (heat sink); to be connected to

the PCB ground

Table 2. Pin description

…continued

Symbol[1][2] Pin Type[3] Description[4]

Product data sheet Rev. 01 — 19 October 2006 7 of 78

NXP Semiconductors ISP1505A; ISP1505C

ULPI HS USB host and peripheral transceiver

7. Functional description

7.1 ULPI interface controller

The ISP1505 provides a 12-pin interface that is compliant with

UTMI+ Low Pin Interface

(UPLI) Speciﬁcation Rev. 1.1

. This interface must be connected to the USB link.

The ULPI interface controller provides the following functions:

•ULPI-compliant interface and register set

•Allows full control over the USB peripheral, host and SRP functionality

•Parses the USB transmit and receive data

•Prioritizes the USB receive data, USB transmit data, interrupts and register operations

•Low-power mode

•External VBUS source control

•VBUS monitoring, charging and discharging

•6-pin serial mode and 3-pin serial mode

•Generates RXCMDs; status updates

•Maskable interrupts

For more information on the ULPI protocol, see Section 9.

7.2 USB serializer and deserializer

The USB data serializer prepares data to transmit on the USB bus. To transmit data, the

USB link sends a transmit command and data on the ULPI bus. The serializer performs

parallel-to-serial conversion, bit stufﬁng and NRZI encoding. For packets with a PID, the

serializer adds a SYNC pattern to the start of the packet, and an EOP pattern to the end

of the packet. When the serializer is busy and cannot accept any more data, the ULPI

interface controller de-asserts NXT.

The USB data deserializer decodes data received from the USB bus. When data is

received, the deserializer strips the SYNC and EOP patterns, and then performs

serial-to-parallel conversion, NRZI decoding and discarding of stuff bits on the data

payload. The ULPI interface controller sends data to the USB link by asserting DIR, and

then asserting NXT whenever a byte is ready. The deserializer also detects various

receive errors, including bit stuff errors, elasticity buffer underrun or overrun, and

byte-alignment errors.

7.3 Hi-Speed USB (USB 2.0) ATX

The Hi-Speed USB ATX block is an analog front-end containing the circuitry needed to

transmit, receive and terminate the USB bus in high-speed, full-speed and low-speed, for

USB peripheral, host and OTG implementations. The following circuitry is included:

•Differential drivers to transmit data at high-speed, full-speed and low-speed

•Differential receiver and single-ended receivers to receive data at high-speed,

full-speed and low-speed

•Squelch circuit to detect high-speed bus activity

Product data sheet Rev. 01 — 19 October 2006 8 of 78

NXP Semiconductors ISP1505A; ISP1505C

ULPI HS USB host and peripheral transceiver

•High-speed disconnect detector

•45 Ω high-speed bus terminations on DP and DM for peripheral and host modes

•1.5 kΩ pull-up resistor on DP for full-speed peripheral mode

•15 kΩ bus terminations on DP and DM for host and OTG modes

For details on controlling resistor settings, see Table 7.

7.4 Voltage regulator

The ISP1505 contains a built-in voltage regulator that conditions the VCC supply for use

inside the ISP1505. The voltage regulator:

•Supports input supply range 3.0V<V

CC < 3.6 V.

•Supplies internal circuitry with 1.8 V and 3.3 V.

Remark: The REG1V8 and REG3V3 pins require external decoupling capacitors. For

details, see Section 16.

7.5 Crystal oscillator and PLL

The ISP1505 has a built-in crystal oscillator and a Phase-Locked Loop (PLL) for clock

generation.

The crystal oscillator takes a sine-wave input from an external crystal, on the XTAL1 pin,

and converts it to a square wave clock for internal use. Alternatively, a square wave clock

of the same frequency can also be directly driven into the XTAL1 pin. Using an existing

square wave clock can save the cost of the crystal and also reduce the board size.

The PLL takes the square wave clock from the crystal oscillator and multiplies or divides it

into various frequencies for internal use. The PLL can also take a 60 MHz input from the

CLOCK pin. This eliminates the need for an external crystal or clock on XTAL1.

The PLL produces the following frequencies, irrespective of the clock source:

•60 MHz clock for the ULPI interface controller

•1.5 MHz for the low-speed USB data

•12 MHz for the full-speed USB data

•480 MHz for the high-speed USB data

•Other internal frequencies for data conversion and data recovery

7.6 VBUS comparators

The ISP1505 provides three comparators, VBUS valid comparator, session valid

comparator and session end comparator, to detect the VBUS voltage level.

7.6.1 VBUS valid comparator

This comparator is used by hosts and A-devices to determine whether the voltage on

VBUS is at a valid level for operation. The ISP1505 minimum threshold for the VBUS valid

comparator is VA_VBUS_VLD. Any voltage on VBUS below VA_VBUS_VLD is considered a fault.

During power-up, it is expected that the comparator output will be ignored.

Product data sheet Rev. 01 — 19 October 2006 9 of 78

NXP Semiconductors ISP1505A; ISP1505C

ULPI HS USB host and peripheral transceiver

While it is possible for the external 5 V supply to use the ISP1505 internal A_VBUS_VLD

comparator, typical 5 V supplies must provide their own power fault indicator that can be

connected as an input to the ISP1505 FAULT pin.

7.6.2 Session valid comparator

The session valid comparator is a TTL-level input that determines when VBUS is high

enough for a session to start. Peripherals, A-devices and B-devices use this comparator to

detect when a session is started. The A-device also uses this comparator to determine

when a session is completed. The session valid threshold of the ISP1505 is VB_SESS_VLD,

with a hysteresis of Vhys(B_SESS_VLD).

7.6.3 Session end comparator

The ISP1505 session end comparator determines when VBUS is below the B-device

session end threshold. The B-device uses this threshold to determine when a session has

ended. The session end threshold of the ISP1505 is VB_SESS_END.

7.7 SRP charge and discharge resistors

The ISP1505 provides on-chip resistors for short-term charging and discharging of VBUS.

These are used by the B-device to request a session, prompting the A-device to restore

the VBUS power. First, the B-device makes sure that VBUS is fully discharged from the

previous session by setting the DISCHRG_VBUS register bit to logic 1 and waiting for

SESS_END to be logic 1. Then the B-device charges VBUS by setting the CHRG_VBUS

threshold and starts a session by turning on the VBUS power.

7.8 Band gap reference voltage

The band gap circuit provides a stable internal voltage reference to bias analog circuitry.

The band gap requires an accurate external reference resistor, RRREF, connected

between the RREF and GND pins. For details, see Section 16.

7.9 Power-on reset

The ISP1505 has an internal power-on reset circuit that resets all internal logic on

power-up. The ULPI interface is also reset at power-up.

Remark: When CLOCK starts toggling after power-up, the USB link must issue a reset

command over the ULPI bus to ensure correct operation of the ISP1505.

7.10 Detailed description of pins

7.10.1 DATA[7:0]

Bidirectional data bus. The USB link must drive DATA[7:0] to LOW when the ULPI bus is

idle. When the link has data to transmit to the PHY, it drives a nonzero value.

Weak pull-down resistors are incorporated into the DATA[7:0] pins as part of the interface

protect feature. For details, see Section 9.3.1.

The data bus can be reconﬁgured to carry various data types, as given in Section 8 and

Section 9.

Product data sheet Rev. 01 — 19 October 2006 10 of 78

NXP Semiconductors ISP1505A; ISP1505C

ULPI HS USB host and peripheral transceiver

7.10.2 VCC(I/O)

The input power pin that sets the I/O voltage level. For details, see Section 12,Section 13

and Section 16. VCC(I/O) provides power to on-chip pads of the following pins:

•CLOCK

•DATA[7:0]

•DIR

•NXT

•RESET_N

•STP

If the ISP1505 CLOCK pin is conﬁgured as an input, the VCC(I/O) power must be provided

at the same time as the VCC power. If the VCC(I/O) power input is delayed with respect to

VCC, input clock mode stability cannot be guaranteed.

7.10.3 RREF

Resistor reference analog I/O pin. A resistor, RRREF, must be connected between RREF

and GND, as shown in Section 16. This provides an accurate voltage reference that

biases internal analog circuitry. Less accurate resistors cannot be used and will render the

ISP1505 unusable.

7.10.4 DP and DM

The DP (data plus) and DM (data minus) are USB differential data pins. These must be

connected to the D+ and D− pins of the USB receptacle.

7.10.5 VCC

VCC is the main input supply voltage for the ISP1505. Decoupling capacitors are

recommended. For details, see Section 16.

7.10.6 VBUS/FAULT

This pin provides two options for VBUS driving and monitoring. If neither function is used,

this pin must be connected to ground.

7.10.6.1 VBUS

By default, this pin acts as an input to VBUS comparators, and also charges and

discharges VBUS for SRP.

The VBUS pin requires a capacitive load as shown in Section 16.

To prevent electrical overstress, it is strongly recommended that you attach a series

resistor on the VBUS pin (RVBUS). RVBUS must not be attached when using the ISP1505

internal charge pump. For details, see Section 16.

7.10.6.2 FAULT (external overcurrent or fault detector)

If an external VBUS overcurrent or fault circuit is used, the output fault indicator of that

circuit can be connected to the ISP1505 FAULT input pin. The ISP1505 will inform the link

of VBUS fault events by sending RXCMDs on the ULPI bus. To use the FAULT pin, the link

must:

Product data sheet Rev. 01 — 19 October 2006 11 of 78

NXP Semiconductors ISP1505A; ISP1505C

ULPI HS USB host and peripheral transceiver

•Set the USE_EXT_VBUS_IND register bit to logic 1.

•Set the polarity of the external fault signal using the IND_COMPL register bit.

•Set the IND_PASSTHRU register bit to logic 1.

7.10.7 REG3V3 and REG1V8

Regulator output voltage. These supplies are used to power the ISP1505 internal digital

and analog circuits, and must not be used to power external circuits.

For correct operation of the regulator, it is recommended that you connect REG3V3 and

REG1V8 to decoupling capacitors. For an example, see Section 16.

7.10.8 XTAL1 and XTAL2

XTAL1 is the crystal input, and XTAL2 is the crystal output. The allowed frequency on the

XTAL1 pin depends on the ISP1505 product version.

If the link requires a 60 MHz clock from the ISP1505, then either a crystal must be

attached, or a clock of the same frequency must be driven into XTAL1, with XTAL2 left

ﬂoating. If the link drives a 60 MHz clock into the CLOCK pin, then XTAL1 must be

connected to REG1V8, and XTAL2 must be left ﬂoating.

If a crystal is attached, it requires external load capacitors to GND on each terminal of the

crystal. For details, see Section 16.

If at any time the system wants to stop the clock on XTAL1, the link must ﬁrst put the

ISP1505 into low-power mode. The clock on XTAL1 must be restarted before low-power

mode is exited.

7.10.9 RESET_N/PSW_N

This pin provides two optional functions. If neither function is used, this pin must be

connected to VCC(I/O).

7.10.9.1 RESET_N

An active LOW asynchronous reset pin that resets all circuits in the ISP1505. The

ISP1505 contains an internal power-on reset circuit, and therefore using the RESET_N

pin is optional. If RESET_N is not used, it must be connected to VCC(I/O).

For details on using RESET_N, see Section 9.3.2.

7.10.9.2 PSW_N

PSW_N is an active LOW, open-drain output pin. This pin can be connected to an active

LOW, external VBUS switch or charge pump enable circuit to control the external VBUS

power source. An external pull-up resistor, Rpullup, is required when PSW_N is used. This

pin is open-drain, allowing ganged-mode power control for multiple USB ports. For

application details, see Section 16.

To use the PSW_N pin, the link must disable the reset input by setting the

IGNORE_RESET bit in the Power Control register to logic 1. This will ensure that PSW_N

is not misinterpreted as a reset.

Product data sheet Rev. 01 — 19 October 2006 12 of 78

NXP Semiconductors ISP1505A; ISP1505C

ULPI HS USB host and peripheral transceiver

If the link is in host mode, it can enable the external VBUS power source by setting the

DRV_VBUS_EXT bit in the OTG Control register to logic 1. The ISP1505 will drive

PSW_N to LOW to enable the external VBUS power source. If the link detects an

overcurrent condition (the VBUS state in RXCMD is not 11b), it must disable the external

VBUS supply by setting DRV_VBUS_EXT to logic 0.

7.10.10 DIR

ULPI direction output pin. Controls the direction of the data bus. By default, the ISP1505

holds DIR at LOW, causing the data bus to be an input. When DIR is LOW, the ISP1505

listens for data from the link. The ISP1505 pulls DIR to HIGH only when it has data to

send to the link, which is for one of two reasons:

•To send the USB receive data, RXCMD status updates and register read data to the

link.

•To block the link from driving the data bus during power-up, reset and low-power

mode (suspend).

For details on DIR usage, refer to

UTMI+ Low Pin Interface (ULPI) Speciﬁcation Rev. 1.1

7.10.11 STP

ULPI stop input pin. The link must assert STP to signal the end of a USB transmit packet

or a register write operation. When DIR is asserted, the link can optionally assert STP to

abort the ISP1505, causing it to de-assert DIR in the next clock cycle. A weak pull-up

resistor is incorporated into the STP pin as part of the interface protect feature. For details,

see Section 9.3.1.

For details on STP usage, refer to

UTMI+ Low Pin Interface (ULPI) Speciﬁcation Rev. 1.1

7.10.12 NXT

ULPI next data output pin. The ISP1505 holds NXT at LOW by default. When DIR is LOW

and the link is sending data to the ISP1505, NXT will be asserted to notify the link to

provide the next data byte. When DIR is at HIGH and the ISP1505 is sending data to the

link, NXT will be asserted to notify the link that another valid byte is on the bus. NXT is not

used for the register read data or the RXCMD status update.

For details on NXT usage, refer to

UTMI+ Low Pin Interface (ULPI) Speciﬁcation Rev. 1.1

7.10.13 CLOCK

A 60 MHz interface clock to synchronize the ULPI bus. CLOCK can be conﬁgured as input

or output. The ISP1505 provides three clocking options:

•A crystal attached between the XTAL1 and XTAL2 pins.

•A clock driven into the XTAL1 pin, with the XTAL2 pin left ﬂoating.

•A 60 MHz clock driven into the CLOCK pin, with XTAL1 tied to REG1V8 and XTAL2

left ﬂoating.

For details on CLOCK usage, refer to

UTMI+ Low Pin Interface (ULPI) Speciﬁcation

Rev. 1.1

Product data sheet Rev. 01 — 19 October 2006 13 of 78

NXP Semiconductors ISP1505A; ISP1505C

ULPI HS USB host and peripheral transceiver

7.10.14 GND (die pad)

Global ground signal. The die pad is exposed on the underside of the package as a

ground plate. This acts as a ground to all circuits in the ISP1505. To ensure correct

operation of the ISP1505, GND must be soldered to the cleanest ground available.

Product data sheet Rev. 01 — 19 October 2006 14 of 78

NXP Semiconductors ISP1505A; ISP1505C

ULPI HS USB host and peripheral transceiver

8. Modes of operation

8.1 ULPI modes

The ISP1505 ULPI bus can be programmed to operate in four modes. Each mode

reconﬁgures the signals on the data bus as described in the following subsections. Setting

more than one mode will lead to undeﬁned behavior.

8.1.1 Synchronous mode

This is default mode. At power-up, and when CLOCK is stable, the ISP1505 will enter

synchronous mode. The link must synchronize all ULPI signals to CLOCK, meeting the

set-up and hold times as deﬁned in Section 15. A description of the ULPI pin behavior in

synchronous mode is given in Table 3.

This mode is used by the link to perform the following tasks:

•High-speed detection handshake (chirp)

•Transmit and receive USB packets

•Read and write to registers

•Receive USB status updates (RXCMDs)

For more information on various synchronous mode protocols, see Section 9.

Table 3. ULPI signal description

Signal

name Directionon

ISP1505 Signal description

CLOCK I/O 60 MHz interface clock. If a crystal is attached or a clock is driven into

the XTAL1 pin, the ISP1505 will drive a 60 MHz output clock; otherwise,

the ISP1505 requires a 60 MHz input clock.

DATA[7:0] I/O 8-bit data bus. In synchronous mode, the link drives DATA[7:0] to LOW

by default. The link initiates transfers by sending a nonzero data pattern

called TXCMD (transmit command). In synchronous mode, the direction

of DATA[7:0] is controlled by DIR. Contents of DATA[7:0] lines must be

ignored for exactly one clock cycle whenever DIR changes value. This is

called the turnaround cycle.

Data lines have ﬁxed direction and different meaning in low-power and

serial modes.

Product data sheet Rev. 01 — 19 October 2006 15 of 78

NXP Semiconductors ISP1505A; ISP1505C

ULPI HS USB host and peripheral transceiver

8.1.2 Low-power mode

When the USB is idle, the link can place the ISP1505 into low-power mode (also called

suspend mode). In low-power mode, the data bus deﬁnition changes to that shown in

Table 4. To enter low-power mode, the link sets the SUSPENDM bit in the Function

Control register to logic 0. To exit low-power mode, the link asserts the STP signal. The

ISP1505 will draw only suspend current from the VCC supply (see Table 41).

During low-power mode, the clock on XTAL1 may be stopped. The clock must be started

again before asserting STP to exit low-power mode. After exiting low-power mode, the

ISP1505 will send an RXCMD to the link if a change was detected in any interrupt source,

and the change still exists. An RXCMD may not be sent if the interrupt condition is

removed before exiting.

For more information on low-power mode enter and exit protocols, refer to

UTMI+ Low Pin

Interface (ULPI) Speciﬁcation Rev. 1.1

DIR O Direction: Controls the direction of data bus DATA[7:0]. In synchronous

mode, the ISP1505 drives DIR to LOW by default, making the data bus

an input so that the ISP1505 can listen for TXCMDs from the link. The

ISP1505 drives DIR to HIGH only when it has data for the link. When

DIR and NXT are HIGH, the byte on the data bus contains decoded

USB data. When DIR is HIGH and NXT is LOW, the byte contains

status information called RXCMD (receive command). The only

exception to this rule is when the PHY returns register read data, where

NXT is also LOW, replacing the usual RXCMD byte. Every change in

DIR causes a turnaround cycle on the data bus, during which DATA[7:0]

is not valid and must be ignored by the link.

DIR is always asserted during low-power and serial modes.

STP I Stop: In synchronous mode, the link drives STP to HIGH for one cycle

after the last byte of data is sent to the ISP1505. The link can optionally

assert STP to force DIR to be de-asserted.

In low-power and serial modes, the link holds STP at HIGH to wake up

the ISP1505, causing the ULPI bus to return to synchronous mode.

NXT O Next: In synchronous mode, the ISP1505 drives NXT to HIGH to

throttle data. If DIR is LOW, the ISP1505 asserts NXT to notify the link

to place the next data byte on DATA[7:0] in the following clock cycle. If

DIR is HIGH, the ISP1505 asserts NXT to notify the link that a valid

USB data byte is on DATA[7:0] in the current cycle. The ISP1505 always

drives an RXCMD when DIR is HIGH and NXT is LOW, unless register

read data is to be returned to the link in the current cycle.

NXT is not used in low-power or serial mode.

Table 3. ULPI signal description

…continued

Signal

name Directionon

ISP1505 Signal description

Table 4. Signal mapping during low-power mode

Signal Maps to Direction Description

LINESTATE0 DATA0 O combinatorial LINESTATE0 directly driven by analog receiver

LINESTATE1 DATA1 O combinatorial LINESTATE1 directly driven by analog receiver

Product data sheet Rev. 01 — 19 October 2006 16 of 78

NXP Semiconductors ISP1505A; ISP1505C

ULPI HS USB host and peripheral transceiver

8.1.3 6-pin full-speed or low-speed serial mode

If the link requires a 6-pin serial interface to transmit and receive full-speed or low-speed

USB data, it can set the ISP1505 to 6-pin serial mode. In 6-pin serial mode, the DATA[7:0]

bus deﬁnition changes to that shown in Table 5. To enter 6-pin serial mode, the link sets

the 6PIN_FSLS_SERIAL bit in the Interface Control register to logic 1. To exit 6-pin serial

mode, the link asserts STP. This is provided primarily for links that contain legacy

full-speed or low-speed functionality, providing a more cost-effective upgrade path to

high-speed. An interrupt pin is also provided to inform the link of USB events. If the link

requires CLOCK to be running during 6-pin serial mode, the CLOCK_SUSPENDM

For more information on 6-pin serial mode enter and exit protocols, refer to

UTMI+ Low

Pin Interface (ULPI) Speciﬁcation Rev. 1.1

8.1.4 3-pin full-speed or low-speed serial mode

If the link requires a 3-pin serial interface to transmit and receive full-speed or low-speed

USB data, it can set the ISP1505 to 3-pin serial mode. In 3-pin serial mode, the data bus

deﬁnition changes to that shown in Table 6. To enter 3-pin serial mode, the link sets the

3PIN_FSLS_SERIAL bit in the Interface Control register to logic 1. To exit 3-pin serial

mode, the link asserts STP. This is primarily provided for links that contain legacy

full-speed or low-speed functionality, providing a more cost-effective upgrade path to

high-speed. An interrupt pin is also provided to inform the link of USB events. If the link

requires CLOCK to be running during 3-pin serial mode, the CLOCK_SUSPENDM

For more information on 3-pin serial mode enter and exit protocols, refer to

UTMI+ Low

Pin Interface (ULPI) Speciﬁcation Rev. 1.1

Reserved DATA2 O reserved; the ISP1505 will drive this pin to LOW

INT DATA3 O active HIGH interrupt indication; will be asserted whenever any unmasked

interrupt occurs

Reserved DATA[7:4] O reserved; the ISP1505 will drive this pin to LOW

Table 4. Signal mapping during low-power mode

…continued

Signal Maps to Direction Description

Table 5. Signal mapping for 6-pin serial mode

Signal Maps to Direction Description

TX_ENABLE DATA0 I active HIGH transmit enable

TX_DAT DATA1 I transmit differential data on DP and DM

TX_SE0 DATA2 I transmit single-ended zero on DP and DM

INT DATA3 O active HIGH interrupt indication; will be asserted whenever any

unmasked interrupt occurs

RX_DP DATA4 O single-ended receive data from DP

RX_DM DATA5 O single-ended receive data from DM

RX_RCV DATA6 O differential receive data from DP and DM

Reserved DATA7 O reserved; the ISP1505 will drive this pin to LOW

Product data sheet Rev. 01 — 19 October 2006 17 of 78

NXP Semiconductors ISP1505A; ISP1505C

ULPI HS USB host and peripheral transceiver

8.2 USB and OTG state transitions

A Hi-Speed USB host or an OTG device handles more than one electrical state as deﬁned

Universal Serial Bus Speciﬁcation Rev. 2.0

and

On-The-Go Supplement to the USB 2.0

Speciﬁcation Rev. 1.2

. The ISP1505 accommodates the various states through register bit

settings of XCVRSELECT[1:0], TERMSELECT, OPMODE[1:0], DP_PULLDOWN and

DM_PULLDOWN.

Table 7 summarizes operating states. The values of register settings in Table 7 will force

resistor settings as also given in Table 7. Resistor setting signals are deﬁned as follows:

•RPU_DP_EN enables the 1.5 kΩ pull-up resistor on DP.

•RPD_DP_EN enables the 15 kΩ pull-down resistor on DP.

•RPD_DM_EN enables the 15 kΩ pull-down resistor on DM.

•HSTERM_EN enables the 45 Ω termination resistors on DP and DM.

It is up to the link to set the desired register settings.

Table 6. Signal mapping for 3-pin serial mode

Signal Maps to Direction Description

TX_ENABLE DATA0 I active HIGH transmit enable

DAT DATA1 I/O transmit differential data on DP and DM when TX_ENABLE is HIGH

receive differential data from DP and DM when TX_ENABLE is LOW

SE0 DATA2 I/O transmit single-ended zero on DP and DM when TX_ENABLE is HIGH

receive single-ended zero from DP and DM when TX_ENABLE is LOW

INT DATA3 O active HIGH interrupt indication; will be asserted whenever any

unmasked interrupt occurs

Reserved DATA[7:4] O reserved; the ISP1505 will drive this pin to LOW

Table 7. Operating states and resistor settings

Signaling mode Register settings Internal resistor settings

XCVR

SELECT

[1:0]

TERM

SELECT OPMODE

[1:0] DP_PULL

DOWN DM_PULL

DOWN RPU_

DP_EN RPD_

DM_EN HSTERM

_EN

General settings

3-state drivers XXb Xb 01b Xb Xb 0b 0b 0b 0b

Power-up or

VBUS <V

B_SESS_END

01b 0b 00b 1b 1b 0b 1b 1b 0b

Host settings

Host chirp 00b 0b 10b 1b 1b 0b 1b 1b 1b

Host high-speed 00b 0b 00b 1b 1b 0b 1b 1b 1b

Host full-speed X1b 1b 00b 1b 1b 0b 1b 1b 0b

Host high-speed or

full-speed suspend 01b 1b 00b 1b 1b 0b 1b 1b 0b

Host high-speed or

full-speed resume 01b 1b 10b 1b 1b 0b 1b 1b 0b

Host low-speed 10b 1b 00b 1b 1b 0b 1b 1b 0b

Product data sheet Rev. 01 — 19 October 2006 18 of 78

NXP Semiconductors ISP1505A; ISP1505C

ULPI HS USB host and peripheral transceiver

Host low-speed

suspend 10b 1b 00b 1b 1b 0b 1b 1b 0b

Host low-speed

resume 10b 1b 10b 1b 1b 0b 1b 1b 0b

Host Test J or Test K 00b 0b 10b 1b 1b 0b 1b 1b 1b

Peripheral settings

Peripheral chirp 00b 1b 10b 0b 0b 1b 0b 0b 0b

Peripheral

high-speed 00b 0b 00b 0b 0b 0b 0b 0b 1b

Peripheral full-speed 01b 1b 00b 0b 0b 1b 0b 0b 0b

Peripheral

high-speed or

full-speed suspend

01b 1b 00b 0b 0b 1b 0b 0b 0b

Peripheral

high-speed or

full-speed resume

01b 1b 10b 0b 0b 1b 0b 0b 0b

Peripheral Test J or

Test K 00b 0b 10b 0b 0b 0b 0b 0b 1b

OTG settings

OTG device

peripheral chirp 00b 1b 10b 0b 1b 1b 0b 1b 0b

OTG device

peripheral

high-speed

00b 0b 00b 0b 1b 0b 0b 1b 1b

OTG device

peripheral full-speed 01b 1b 00b 0b 1b 1b 0b 1b 0b

OTG device

peripheral

high-speed and

full-speed suspend

01b 1b 00b 0b 1b 1b 0b 1b 0b

OTG device

peripheral

high-speed and

full-speed resume

01b 1b 10b 0b 1b 1b 0b 1b 0b

OTG device

peripheral Test J or

Test K

00b 0b 10b 0b 1b 0b 0b 1b 1b

Table 7. Operating states and resistor settings

…continued

Signaling mode Register settings Internal resistor settings

XCVR

SELECT

[1:0]

TERM

SELECT OPMODE

[1:0] DP_PULL

DOWN DM_PULL

DOWN RPU_

DP_EN RPD_

DM_EN HSTERM

_EN

Product data sheet Rev. 01 — 19 October 2006 19 of 78

NXP Semiconductors ISP1505A; ISP1505C

ULPI HS USB host and peripheral transceiver

9. Protocol description

The following subsections describe the protocol for using the ISP1505.

9.1 ULPI references

The ISP1505 provides a 12-pin ULPI interface to communicate with the link. It is highly

recommended that you read

UTMI+ Low Pin Interface (ULPI) Speciﬁcation Rev. 1.1

and

UTMI+ Speciﬁcation Rev. 1.0

9.2 Power-On Reset (POR)

An internal POR is generated when REG1V8 rises above VPOR(trip), for at least

tw(REG1V8_H). The internal POR pulse will also be generated whenever REG1V8 drops

below VPOR(trip) for more than tw(REG1V8_L), and then rises above VPOR(trip) again. The

voltage on REG1V8 is generated from VCC.

To give a better view of the functionality, Figure 3 shows a possible curve of REG1V8. The

internal POR starts with logic 0 at t0. At t1, the detector will see the passing of the trip

level so that POR turns to logic 1 and a delay element will add another tPORP before it

drops to logic 0. If REG1V8 dips from t2 to t3 for > tw(REG1V8_L), another POR pulse is

generated. If the dip at t4 to t5 is too short, that is, < tw(REG1V8_L), the internal POR pulse

will not react and will remain LOW.

9.3 Power-up, reset and bus idle sequence

Figure 4 shows a typical start-up sequence.

On power-up, the ISP1505 performs an internal power-on reset and asserts DIR to

indicate to the link that the ULPI bus cannot be used. On power-up, CLOCK is an input

unless several edges are detected on XTAL1. When the internal PLL is stable, the

ISP1505 de-asserts DIR. The power-up time depends on the VCC supply rise time, the

crystal start-up time, and PLL start-up time tstartup(o)(CLOCK). Whenever DIR is asserted,

the ISP1505 drives the NXT pin to LOW and drives DATA[7:0] with RXCMD values. When

DIR is de-asserted, the link must drive the data bus to a valid level. By default, the link

must drive data to LOW. When the ISP1505 initially de-asserts DIR on power-up, the link

must ignore all RXCMDs until it resets the ISP1505. Before beginning USB packets, the

link must set the RESET bit in the Function Control register to reset the ISP1505. After the

RESET bit is set, the ISP1505 will assert DIR until the internal reset completes. The

ISP1505 will automatically de-assert DIR and clear the RESET bit when reset has

Fig 3. Internal power-on reset timing

004aaa751

REG1V8

t0 t1 t2 t3 t4 t5

VPOR(trip)

tPORP POR

tPORP

Product data sheet Rev. 01 — 19 October 2006 20 of 78

NXP Semiconductors ISP1505A; ISP1505C

ULPI HS USB host and peripheral transceiver

completed. After every reset, an RXCMD is sent to the link to update USB status

information. After this sequence, the ULPI bus is ready for use and the link can start USB

operations.

If a crystal is attached or a clock is driven into the XTAL1 pin, the ISP1505 will drive a

60 MHz clock out from the CLOCK pin when DIR de-asserts. This is shown as CLOCK

(output) in Figure 4. If no crystal is attached and a 60 MHz clock is driven into the CLOCK

pin, DIR will de-assert when internal clocks have synchronized. This is shown as CLOCK

(input) in Figure 4.

The recommended power-up sequence for the link is as follows:

•The link waits for 1 ms, ignoring all the ULPI pin status.

•The link may start to detect DIR status level. If DIR is detected as LOW for three clock

cycles, the link may send a RESET command.

•The ULPI interface is ready for use.

Product data sheet Rev. 01 — 19 October 2006 21 of 78

NXP Semiconductors ISP1505A; ISP1505C

ULPI HS USB host and peripheral transceiver

t1 = VCC and VCC(I/O) are applied to the ISP1505. The ISP1505 regulator starts to turn on. If the ISP1505 CLOCK pin is

conﬁgured as an input, the VCC(I/O) power must be provided at the same time as the VCC power. If the VCC(I/O) power input is

delayed with respect to VCC, input clock mode stability cannot be guaranteed.

t2 = ULPI pads detect REG1V8 rising above the REG1V8 regulator threshold and are not in 3-state. These pads may drive

either LOW or HIGH. It is recommended that the link ignores the ULPI pins status during tPWRUP.

t3 = The POR threshold is reached and the POR pulse is generated. After the POR pulse, ULPI pins are driven to a deﬁned

level. DIR is driven to HIGH and the other pins are driven to LOW.

t4 = The 19.2 MHz or 26 MHz input clock starts. This clock may be started any time.

t5 = The internal PLL is stabilized after tstartup(PLL). If the 19.2 MHz or 26 MHz clock is started before POR, the internal PLL

will be stabilized after tstartup(PLL) from POR. The CLOCK pin starts to output 60 MHz. The DIR pin will transition from HIGH

to LOW. The DIR pin will remain LOW before the link issues a RESET command to the ISP1505.

t6 = The power-up sequence is completed and the ULPI bus interface is ready for use.

Fig 4. Power-up and reset sequence required before the ULPI bus is ready for use

CLOCK

(output)

TXCMD

DIR

DATA[7:0]

STP

NXT

004aaa885

RESET command

internal clocks stable

internal reset RXCMD

update

bus idle

VCC

VCC(I/O)

REG1V8

internal

REG1V8

detector

internal

POR

XTAL1

(output)

tstartup(PLL)

t1 t2 t3 t4 t5 t6

tPWRUP

CLOCK

(input)

XTAL1

(input)

Product data sheet Rev. 01 — 19 October 2006 22 of 78

NXP Semiconductors ISP1505A; ISP1505C

ULPI HS USB host and peripheral transceiver

9.3.1 Interface protection

By default, the ISP1505 enables a weak pull-up resistor on STP. If the STP pin is

unexpectedly HIGH at any time, the ISP1505 will protect the ULPI interface by enabling

weak pull-down resistors on DATA[7:0].

The interface protect feature prevents unwanted activity of the ISP1505 whenever the

ULPI interface is not correctly driven by the link. For example, when the link powers up

more slowly than the ISP1505.

The interface protect feature can be disabled by setting the INTF_PROT_DIS bit to logic 1.

9.3.2 Interface behavior with respect to RESET_N

The use of the RESET_N pin is optional. When RESET_N is asserted (LOW), the

ISP1505 will assert DIR. All logic in the ISP1505 will be reset, including the analog

circuitry and ULPI registers. During reset, the link must drive DATA[7:0] and STP to LOW;

otherwise undeﬁned behavior may result. When RESET_N is de-asserted (HIGH), the

DIR output will de-assert (LOW) four or ﬁve clock cycles later. Figure 5 shows the ULPI

interface behavior when RESET_N is asserted (LOW), and when RESET_N is

subsequently de-asserted (HIGH). If RESET_N is not used, it must be tied to VCC(I/O).

9.4 VBUS power and fault detection

9.4.1 Driving 5 V on VBUS

The ISP1505 supports external 5 V supplies. The ISP1505 can control the external supply

using the active-LOW PSW_N open-drain output pin. To enable the external supply by

driving PSW_N to LOW, the link must set the DRV_VBUS_EXT bit in the OTG Control

any value and will be ignored.

Fig 5. Interface behavior with respect to RESET_N

CLOCK

004aaa720

STP

RESET_N

DATA[7:0]

DIR

NXT

Hi-Z (input)

Hi-Z (link must drive)

Product data sheet Rev. 01 — 19 October 2006 23 of 78

NXP Semiconductors ISP1505A; ISP1505C

ULPI HS USB host and peripheral transceiver

9.4.2 Fault detection

The ISP1505 supports external VBUS fault detector circuits. An overcurrent detection

circuit is required for host applications that supply more than 100 mA on VBUS for voltages

between 4.75 V to 5.25 V. For low-power applications supplying less than 100 mA, the

VBUS power line can directly be connected to the VBUS pin on the ISP1505 and the link can

utilize the internal A_VBUS_VLD comparator.

The ISP1505 supports external VBUS fault detector circuits that output a digital fault

indicator signal. The indicator signal must be connected to the VBUS/FAULT pin. To enable

the ISP1505 to monitor the digital overcurrent input, the link must set the

USE_EXT_VBUS_IND bit in the OTG Control register. By default, the digital indicator is

interpreted by the ISP1505 as active LOW. That is, a LOW value on VBUS/FAULT indicates

a fault condition has been detected. If the external fault detector provides an active HIGH

digital indicator, the link must set the IND_COMPL bit in the Interface Control register to

logic 1. The IND_PASSTHRU bit must be set to logic 1.

By default, the ISP1505 will qualify the external FAULT input with the internal VBUS valid

comparator. This can be disabled by setting the IND_PASSTHRU bit to logic 0.

9.5 TXCMD and RXCMD

Commands between the ISP1505 and the link are described in the following subsections.

9.5.1 TXCMD

By default, the link must drive the ULPI bus to its idle state of 00h. To send commands and

USB packets, the link drives a nonzero value on DATA[7:0] to the ISP1505 by sending a

byte called TXCMD. Commands include USB packet transmissions, and register reads

and writes. Once the TXCMD is interpreted and accepted by the ISP1505, the NXT signal

is asserted and the link can follow up with the required number of data bytes. The TXCMD

byte format is given in Table 8. Any values other than those in Table 8 are illegal and may

result in undeﬁned behavior.

Various TXCMD packet and register sequences are shown in later sections.

Table 8. TXCMD byte format

Command

type name Command code

DATA[7:6] Command

payload DATA[5:0] Command

name Command description

Idle 00b 00 0000b NOOP No operation. 00h is the idle value of the data bus. The

link must drive NOOP by default.

Packet

transmit 01b 00 0000b NOPID Transmit USB data that does not have a PID, such as

chirp and resume signaling. The ISP1505 starts

transmitting only after accepting the next data byte.

00 XXXXb PID Transmit USB packet. DATA[3:0] indicates USB packet

identiﬁer PID[3:0].

Product data sheet Rev. 01 — 19 October 2006 24 of 78

NXP Semiconductors ISP1505A; ISP1505C

ULPI HS USB host and peripheral transceiver

9.5.2 RXCMD

The ISP1505 communicates status information to the link by asserting DIR and sending

an RXCMD byte on the DATA bus. The RXCMD data byte format is given in Table 9.

The ISP1505 will automatically send an RXCMD whenever there is a change in any of the

RXCMD data ﬁelds. The link must be able to accept an RXCMD at any time; including

single RXCMDs, back-to-back RXCMDs, and RXCMDs at any time during USB receive

packets when NXT is LOW. An example is shown in Figure 6. For details and diagrams,

refer to

UTMI+ Low Pin Interface (ULPI) Speciﬁcation Rev. 1.1

An RXCMD may not be sent when exiting low-power mode or serial mode, if the interrupt

condition is removed before exiting.

write 10b 10 1111b EXTW Extended register write command (optional). The 8-bit

address must be provided after the command is

accepted.

XX XXXXb REGW Register write command with 6-bit immediate address.

read 11b 10 1111b EXTR Extended register read command (optional). The 8-bit

address must be provided after the command is

accepted.

XX XXXXb REGR Register read command with 6-bit immediate address.

Table 8. TXCMD byte format

…continued

Command

type name Command code

DATA[7:6] Command

payload DATA[5:0] Command

name Command description

Table 9. RXCMD byte format

DATA Name Description and value

1 to 0 LINESTATE LINESTATE signals: For a deﬁnition of LINESTATE, see Section 9.5.2.1.

DATA0 — LINESTATE[0]

DATA1 — LINESTATE[1]

3to2 V

BUS state Encoded VBUS voltage state: For an explanation of the VBUS state, see Section 9.5.2.2.

Value VBUS voltage SESS_END SESS_VLD A_VBUS_VLD

00 VBUS <V

B_SESS_END 100

01 VB_SESS_END ≤VBUS < VB_SESS_VLD 000

10 VB_SESS_VLD ≤VBUS < VA_VBUS_VLD X10

11 VBUS ≥VA_VBUS_VLD XX1

5 to 4 RxEvent Encoded USB event signals: For an explanation of RxEvent, see Section 9.5.2.3.

Value RxActive RxError HostDisconnect

00 0 0 0

01 1 0 0

11 1 1 0

10 X X 1

6 reserved -

7 ALT_INT By default, this signal is not used and is not needed in typical designs. Optionally, the link can

enable the BVALID_RISE and/or BVALID_FALL bits in the Power Control register. Corresponding

changes in BVALID will cause an RXCMD to be sent to the link with the ALT_INT bit asserted.

Product data sheet Rev. 01 — 19 October 2006 25 of 78

NXP Semiconductors ISP1505A; ISP1505C

ULPI HS USB host and peripheral transceiver

9.5.2.1 Linestate encoding

LINESTATE[1:0] reﬂects the current state of DP and DM. Whenever the ISP1505 detects

a change in DP or DM, an RXCMD will be sent to the link with the new LINESTATE[1:0]

value. The value given on LINESTATE[1:0] depends on the setting of various registers.

Table 10 shows the LINESTATE[1:0] encoding for upstream facing ports, which applies to

peripherals. Table 11 shows the LINESTATE[1:0] encoding for downstream facing ports,

which applies to Host Controllers. Dual-role devices must choose the correct table,

depending on whether it is in peripheral or host mode.

[1] !squelch indicates inactive squelch. !HS_Differential_Receiver_Output indicates inactive HS_Differential_Receiver_Output.

Fig 6. Single and back-to-back RXCMDs from the ISP1505 to the link

CLOCK

RXCMD

DATA[7:0]RXCMD RXCMD

004aaa695

DIR

STP

NXT

Single RXCMD Back-to-back RXCMDs

turnaround turnaround turnaround turnaround

Table 10. LINESTATE[1:0] encoding for upstream facing ports: peripherals

DP_PULLDOWN = 0.

[1]

Mode Full-speed High-speed Chirp

XCVRSELECT[1:0] 01, 11 00 00

TERMSELECT 1 0 1

LINESTATE[1:0] 00 SE0 squelch squelch

01 FS-J !squelch !squelch and HS_Differential_Receiver_Output

10 FS-K invalid !squelch and !HS_Differential_Receiver_Output

11 SE1 invalid invalid

Product data sheet Rev. 01 — 19 October 2006 26 of 78

NXP Semiconductors ISP1505A; ISP1505C

ULPI HS USB host and peripheral transceiver

[1] !squelch indicates inactive squelch. !HS_Differential_Receiver_Output indicates inactive HS_Differential_Receiver_Output.

9.5.2.2 VBUS state encoding

USB devices must monitor the VBUS voltage for purposes such as overcurrent detection,

starting a session and SRP. The VBUS state ﬁeld in the RXCMD is an encoding of the

voltage level on VBUS.

The A_VBUS_VLD, SESS_VLD and SESS_END indicators in the VBUS state are directly

taken from internal comparators built-in to the ISP1505, and encoded as shown in Table 9.

An RXCMD may not be sent when exiting low-power mode or serial mode, if the interrupt

condition is removed before exiting.

Note that VBUS and FAULT share the same pin and cannot be simultaneously used.

A_VBUS_VLD and FAULT will be interpreted by the ISP1505 as shown in Figure 7.

A description on how to use and select the VBUS state encoding is given in Section “Using

and selecting the VBUS state encoding”.

Table 11. LINESTATE[1:0] encoding for downstream facing ports: host

DP_PULLDOWN and DM_PULLDOWN = 1.

[1]

Mode Low-speed Full-speed High-speed Chirp

XCVRSELECT[1:0] 10 01, 11 00 00

TERMSELECT 1 1 0 0

OPMODE[1:0] X X 00, 01, 11 10

LINESTATE[1:0] 00 SE0 SE0 squelch squelch

01 LS-K FS-J !squelch !squelch and HS_Differential_Receiver_Output

10 LS-J FS-K invalid !squelch and !HS_Differential_Receiver_Output

11 SE1 SE1 invalid invalid

Fig 7. RXCMD A_VBUS_VLD indicator source

004aaa752

VBUS/FAULT (0, X)

IND_COMPL

(1, 1)

USE_EXT_VBUS_IND,

IND_PASSTHRU

RXCMD

A_VBUS_VLD

A_VBUS_VLD comparator

(VBUS < 4.4 V)

internal A_VBUS_VLD

complement output

Product data sheet Rev. 01 — 19 October 2006 27 of 78

NXP Semiconductors ISP1505A; ISP1505C

ULPI HS USB host and peripheral transceiver

Using and selecting the VBUS state encoding: The VBUS state encoding is shown in

Table 9. The ISP1505 will send an RXCMD to the link whenever there is a change in the

VBUS state. To receive the VBUS state updates, the link must ﬁrst enable the corresponding

interrupts in the USB Interrupt Enable Rising Edge and USB Interrupt Enable Falling Edge

registers.

The link can use the VBUS state to monitor VBUS and take appropriate action. Table 12

shows the recommended usage for typical applications.

Standard USB Host Controllers: For standard hosts, the system must be able to provide

500 mA on VBUS in the range of 4.75 V to 5.25 V. An external circuit must be used to

detect overcurrent conditions. If the external overcurrent detector provides a digital fault

signal, then the fault signal must be connected to the ISP1505 FAULT input pin, and the

link must do the following:

1. If the external overcurrent circuit has an active LOW fault or overcurrent indicator, set

the IND_COMPL bit in the Interface Control register to logic 1.

2. Set the IND_PASSTHRU bit in the Interface Control register to logic 1.

3. Set the USE_EXT_VBUS_IND bit in the OTG Control register to logic 1.

Standard USB Peripheral Controllers: Standard peripherals must be able to detect

when VBUS is at a sufﬁcient level for operation. SESS_VLD must be enabled to detect the

start and end of USB peripheral operations. Detection of A_VBUS_VLD and SESS_END

thresholds is not needed for standard peripherals.

OTG devices: The ISP1505 provides partial OTG support. A low-power OTG A-device

that supplies less than 100 mA on VBUS can connect the VBUS power to the ISP1505 VBUS

pin. The internal A_VBUS_VLD comparator can be used. If the OTG A-device provides

more than 100 mA on VBUS, an overcurrent detector must be used and "Standard USB

Host Controllers" applies. The OTG A-device also uses SESS_VLD to detect when an

OTG A-device is initiating VBUS pulsing SRP.

When an OTG device is conﬁgured as an OTG B-device, SESS_VLD must be used to

detect when VBUS is at a sufﬁcient level for operation. SESS_END must be used to detect

when VBUS has dropped to a LOW level, allowing the B-device to safely initiate VBUS

pulsing SRP.

9.5.2.3 RxEvent encoding

The RxEvent ﬁeld of the RXCMD informs the link of information related packets received

on the USB bus. RxActive and RxError are deﬁned in

USB 2.0 Transceiver Macrocell

Interface (UTMI) Speciﬁcation Ver. 1.05

. HostDisconnect is deﬁned in

UTMI+

Speciﬁcation Rev. 1.0

. A short deﬁnition is also given in the following subsections.

Table 12. VBUS indicators in RXCMD for typical applications

Application A_VBUS_VLD SESS_VLD SESS_END

Standard host yes no no

Standard peripheral no yes no

OTG A-device yes yes no

OTG B-device no yes yes

Product data sheet Rev. 01 — 19 October 2006 28 of 78

NXP Semiconductors ISP1505A; ISP1505C

ULPI HS USB host and peripheral transceiver

RxActive: When the ISP1505 has detected a SYNC pattern on the USB bus, it signals an

RxActive event to the link. An RxActive event can be communicated using two methods.

The ﬁrst method is for the ISP1505 to simultaneously assert DIR and NXT. The second

method is for the ISP1505 to send an RXCMD to the link with the RxActive ﬁeld in

RxEvent bits set to logic 1. The link must be able to detect both methods. RxActive frames

the receive packet from the ﬁrst byte to the last byte.

The link must assume that RxActive is set to logic 0 when indicated in an RXCMD or when

DIR is de-asserted, whichever occurs ﬁrst.

The link uses RxActive to time high-speed packets and ensure that bus turnaround times

are met. For more information on the USB packet timing, see Section 9.8.1.

RxError: When the ISP1505 has detected an error while receiving a USB packet, it

de-asserts NXT and sends an RXCMD with the RxError ﬁeld set to logic 1. The received

packet is no longer valid and must be dropped by the link.

HostDisconnect: HostDisconnect is encoded into the RxEvent ﬁeld of the RXCMD.

HostDisconnect is valid only when the ISP1505 is conﬁgured as a host (both

DP_PULLDOWN and DM_PULLDOWN are set to logic 1), and indicates to the Host

Controller when a peripheral is connected or disconnected. The Host Controller must

enable HostDisconnect by setting the HOST_DISCON_R and HOST_DISCON_F bits in

the USB Interrupt Enable Rising Edge and USB Interrupt Enable Falling Edge registers,

respectively. Changes in HostDisconnect will cause the PHY to send an RXCMD to the

link with the updated value.

9.6 Register read and write operations

Figure 8 shows register read and write sequences. The ISP1505 supports immediate

addressing and extended addressing register operations. Extended register addressing is

optional for links. Note that register operations will be aborted if the ISP1505 unexpectedly

asserts DIR during the operation. When a register operation is aborted, the link must retry

until successful. For more information on register operations, refer to

UTMI+ Low Pin

Interface (ULPI) Speciﬁcation Rev. 1.1

Product data sheet Rev. 01 — 19 October 2006 29 of 78

NXP Semiconductors ISP1505A; ISP1505C

ULPI HS USB host and peripheral transceiver

9.7 USB reset and high-speed detection handshake (chirp)

Figure 9 shows the sequence of events for USB reset and high-speed detection

handshake (chirp). The sequence is shown for hosts and peripherals. Figure 9 does not

show all RXCMD updates and timing is not to scale. The sequence is as follows:

1. USB reset: The host detects a peripheral attachment as low-speed if DM is HIGH and

as full-speed if DP is HIGH. If a host detects a low-speed peripheral, it does not follow

the remainder of this protocol. If a host detects a full-speed peripheral, it resets the

peripheral by writing to the Function Control register and setting

XCVRSELECT[1:0] = 00b (high-speed) and TERMSELECT = 0b, which drives SE0

on the bus (DP and DM connected to ground through 45 Ω). The host also sets

OPMODE[1:0] = 10b for correct chirp transmit and receive. The start of SE0 is labeled

T0.

Remark: To receive the chirp signaling, the host must also consider the high-speed

differential receiver output. The Host Controller must interpret LINESTATE[1:0] as

shown in Table 11.

2. High-speed detection handshake (chirp)

a. Peripheral chirp: After detecting SE0 for no less than 2.5 µs, if the peripheral is

capable of high-speed, it sets XCVRSELECT[1:0] = 00b (high-speed) and

OPMODE[1:0] = 10b (chirp). The peripheral immediately follows this with a

TXCMD (NOPID), transmitting a Chirp K for no less than 1 ms and ending no more

than 7 ms after reset time T0. If the peripheral is in low-power mode, it must wake

up its clock within 5.6 ms, leaving 200 µs for the link to start transmitting the

Chirp K, and 1.2 ms for the Chirp K to complete (worst case with 10 % slow clock).

b. Host chirp: If the host does not detect the peripheral chirp, it must continue

asserting SE0 until the end of reset. If the host detects the peripheral Chirp K for

no less than 2.5 µs, then no more than 100 µs after the bus leaves the Chirp K

AD indicates the address byte, and D indicates the data byte.

Fig 8. Example of register write, register read, extended register write and extended register read

CLOCK

DIR

DATA[7:0]

NXT

004aaa710

DTXCMD

(EXTW) AD D

immediate

TXCMD

(REGW) TXCMD

(REGR) DAD

TXCMD

(EXTW) D

STP

extended

Product data sheet Rev. 01 — 19 October 2006 30 of 78

NXP Semiconductors ISP1505A; ISP1505C

ULPI HS USB host and peripheral transceiver

state, the host sends a TXCMD (NOPID) with an alternating sequence of Chirp Ks

and Js. Each Chirp K or Chirp J must last for no less than 40 µs and no longer than

60 µs.

c. High-speed idle: The peripheral must detect a minimum of Chirp K-J-K-J-K-J. Each

Chirp K and Chirp J must be detected for at least 2.5 µs. After seeing that

minimum sequence, the peripheral sets TERMSELECT = 0b and

OPMODE[1:0] = 00b. The peripheral is now in high-speed mode and sees !squelch

(01b on LINESTATE). When the peripheral sees squelch (10b on LINESTATE), it

knows that the host has completed chirp and waits for the high-speed USB trafﬁc

to begin. After transmitting the chirp sequence, the host changes OPMODE[1:0] to

00b and begins sending USB packets.

For more information, refer to

UTMI+ Low Pin Interface (ULPI) Speciﬁcation Rev. 1.1

Product data sheet Rev. 01 — 19 October 2006 31 of 78

NXP Semiconductors ISP1505A; ISP1505C

ULPI HS USB host and peripheral transceiver

Timing is not to scale.

Fig 9. USB reset and high-speed detection handshake (chirp) sequence

004aaa711

DATA

[7:0]

TXCMD

NOPID J ... TXCMD

(REGW)

TXCMD

(REGW) SE0 K

DIR

STP

NXT

XCVR

SELECT

TERM

SELECT

01 (FS) 00 (HS)

MODE

00 (normal) 01 (chirp) 00 (normal)

LINE

STATE

J (01b) SE0 (00b) peripheral chirp K (10b) squelch (00b)

host chirp K (10b) or chirp J (01b)

squelch

(00b)

ULPI host

DATA

[7:0]

TXCMD

NOPID K...

SE0 TXCMD

(REGW) 00 KJKJKJTXCMD

(REGW) 00

DIR

STP

NXT

XCVR

SELECT

01 (FS) 00 (HS)

TERM

SELECT

MODE

00 (normal) 10 (chirp) 00 (normal)

LINE

STATE

J (01b) SE0 (00b) peripheral chirp K (10b) !squelch

(01b)

host chirp K or J (10b or 01b)

squelch

(00b) squelch (00b)

ULPI peripheral

USB signals

USB reset high-speed detection handshake (chirp)

peripheral chirp host chirp HS idle

RXCMDs

Product data sheet Rev. 01 — 19 October 2006 32 of 78

NXP Semiconductors ISP1505A; ISP1505C

ULPI HS USB host and peripheral transceiver

9.8 USB packet transmit and receive

An example of a packet transmit and receive is shown in Figure 10. For details on USB

packets, refer to

UTMI+ Low Pin Interface (ULPI) Speciﬁcation Rev. 1.1

9.8.1 USB packet timing

9.8.1.1 ISP1505 pipeline delays

The ISP1505 delays are shown in Table 13. For a detailed description, refer to

UTMI+ Low

Pin Interface (ULPI) Speciﬁcation Rev. 1.1

, Section 3.8.2.6.2.

9.8.1.2 Allowed link decision time

The amount of clock cycles allocated to the link to respond to a received packet and

correctly receive back-to-back packets is given in Table 14. Link designs must follow

values given in Table 14 for correct USB system operation. Examples of high-speed

packet sequences and timing are shown in Figure 11 and Figure 12. For details, refer to

UTMI+ Low Pin Interface (ULPI) Speciﬁcation Rev. 1.1

, Section 3.8.2.6.3.

Fig 10. Example of using the ISP1505 to transmit and receive USB data

CLOCK

TXCMD DATA

DATA[7:0]turnaround RXCMD DATA turnaround

DIR

STP

NXT

004aaa705

link sends

TXCMD

ISP1505

accepts

TXCMD

link sends

the next data;

ISP1505

accepts link signals

end of data ULPI bus

is idle

ISP1505

asserts DIR,

causing

turnaround

cycle

ISP1505

sends

RXCMD

(NXT LOW)

ISP1505

sends

USB data

(NXT HIGH)

ISP1505

deasserts

DIR, causing

turnaround

cycle

Table 13. PHY pipeline delays

Parameter name High-speed PHY delay Full-speed PHY delay Low-speed PHY delay

RXCMD delay (J and K) 4 4 4

RXCMD delay (SE0) 4 4 to 6 16 to 18

TX start delay 1 to 2 6 to 10 74 to 75

TX end delay (packets) 3 to 4 not applicable not applicable

TX end delay (SOF) 6 to 9 not applicable not applicable

RX start delay 5 to 6 not applicable not applicable

RX end delay 5 to 6 17 to 18 122 to 123

Product data sheet Rev. 01 — 19 October 2006 33 of 78

NXP Semiconductors ISP1505A; ISP1505C

ULPI HS USB host and peripheral transceiver

Table 14. Link decision times

Packet sequence High-speed

link delay Full-speed

link delay Low-speed

link delay Deﬁnition

Transmit-Transmit

(host only) 15 to 24 7 to 18 77 to 247 Number of clocks a host link must wait before driving the

TXCMD for the second packet.

In high-speed, the link starts counting from the assertion of

STP for the ﬁrst packet.

In full-speed, the link starts counting from the RXCMD,

indicating LINESTATE has changed from SE0 to J for the

ﬁrst packet. The timing given ensures inter-packet delays of

2 bit times to 6.5 bit times.

Receive-Transmit

(host or

peripheral)

1 to 14 7 to 18 77 to 247 Number of clocks the link must wait before driving the

TXCMD for the transmit packet.

In high-speed, the link starts counting from the end of the

receive packet; de-assertion of DIR or an RXCMD,

indicating RxActive is LOW.

In full-speed or low-speed, the link starts counting from the

RXCMD, indicating LINESTATE has changed from SE0 to J

for the receive packet. The timing given ensures

inter-packet delays of 2 bit times to 6.5 bit times.

Receive-Receive

(peripheral only) 1 1 1 Minimum number of clocks between consecutive receive

packets. The link must be able to receive both packets.

Transmit-Receive

(host or

peripheral)

92 80 718 Host or peripheral transmits a packet and will time-out after

this amount of clock cycles if a response is not received.

Any subsequent transmission can occur after this time.

Fig 11. High-speed transmit-to-transmit packet timing

004aaa712

DP or

DM DATA EOP IDLE SYNC

CLOCK

DN−1DN

DATA

[7:0]

TXCMD D1

DIR

STP

NXT

TX end delay (two to five clocks) link decision time (15 to 24 clocks) TX start delay

(one to two clocks)

USB interpacket delay (88 to 192 high-speed bit times)

Product data sheet Rev. 01 — 19 October 2006 34 of 78

NXP Semiconductors ISP1505A; ISP1505C

ULPI HS USB host and peripheral transceiver

9.9 Preamble

Preamble packets are headers to low-speed packets that must travel over a full-speed

bus, between a host and a hub. To enter preamble mode, the link sets

XCVRSELECT[1:0] = 11b in the Function Control register. When in preamble mode, the

ISP1505 operates just as in full-speed mode, and sends all data with the full-speed rise

and fall times. Whenever the link transmits a USB packet in preamble mode, the ISP1505

will automatically send a preamble header at full-speed bit rate before sending the link

packet at low-speed bit rate. The ISP1505 will ensure a minimum gap of four full-speed bit

times between the last bit of the full-speed PRE PID and the ﬁrst bit of the low-speed

packet SYNC. The ISP1505 will drive a J for at least one full-speed bit time after sending

the PRE PID, after which the pull-up resistor can hold the J state on the bus. An example

transmit packet is shown in Figure 13.

In preamble mode, the ISP1505 can also receive low-speed packets from the full-speed

bus.

Fig 12. High-speed receive-to-transmit packet timing

004aaa713

DP or

DM DATA EOP IDLE SYNC

CLOCK

DN−4

DN−3

DATA

[7:0]

TXCMD D1

DIR

STP

NXT

RX end delay

(three to eight clocks) link decision time (1 to 14 clocks) TX start delay

(one to two clocks)

USB interpacket delay (8 to 192 high-speed bit times)

DN−2

DN−1

turnaround

Product data sheet Rev. 01 — 19 October 2006 35 of 78

NXP Semiconductors ISP1505A; ISP1505C

ULPI HS USB host and peripheral transceiver

9.10 USB suspend and resume

9.10.1 Full-speed and low-speed host-initiated suspend and resume

Figure 14 illustrates how a host or a hub places a full-speed or low-speed peripheral into

suspend and sometime later initiates resume signaling to wake up the downstream

peripheral. Note that Figure 14 timing is not to scale, and does not show all RXCMD

LINESTATE updates.

The sequence of events for a host and a peripheral, both with ISP1505, is as follows:

1. Idle: Initially, the host and the peripheral are idle. The host has its 15 kΩ pull-down

resistors enabled (DP_PULLDOWN and DM_PULLDOWN are set to 1b) and 45 Ω

terminations disabled (TERMSELECT is set to 1b). The peripheral has the 1.5 kΩ

pull-up resistor connected to DP for full-speed or DM for low-speed (TERMSELECT is

set to 1b).

2. Suspend: When the peripheral sees no bus activity for 3 ms, it enters the suspend

state. The peripheral link places the PHY into low-power mode by setting the

SUSPENDM bit in the Function Control register, causing the PHY to draw only

suspend current. The host may or may not be powered down.

3. Resume K: When the host wants to wake up the peripheral, it sets OPMODE[1:0] to

10b and transmits a K for at least 20 ms. The peripheral link sees the resume K on

LINESTATE, and asserts STP to wake up the PHY.

4. EOP: When STP is asserted, the ISP1505 on the host side automatically appends an

EOP of two bits of SE0 at low-speed bit rate, followed by one bit of J. The ISP1505 on

the host side knows to add the EOP because DP_PULLDOWN and DM_PULLDOWN

are set to 1b for a host. After the EOP is completed, the host link sets OPMODE[1:0]

to 00b for normal operation. The peripheral link sees the EOP and also resumes

normal operation.

DP and DM timing is not to scale.

Fig 13. Preamble sequence

CLOCK

TXCMD (low-speed packet ID) D1

DATA[7:0]

DIR

STP

NXT

004aaa714

DP or DM FS SYNC FS

PRE ID IDLE (min

4 FS bits) LS SYNC LS PID LS D0 LS D1

Product data sheet Rev. 01 — 19 October 2006 36 of 78

NXP Semiconductors ISP1505A; ISP1505C

ULPI HS USB host and peripheral transceiver

9.10.2 High-speed suspend and resume

Figure 15 illustrates how a host or a hub places a high-speed enabled peripheral into

suspend and then initiates resume signaling. The high-speed peripheral will wake up and

return to high-speed operations. Note that Figure 15 timing is not to scale, and does not

show all RXCMD LINESTATE updates.

Timing is not to scale.

Fig 14. Full-speed suspend and resume

DATA

[7:0]

TXCMD

NOPID K...

TXCMD

(REGW)

DIR

STP

NXT

OPMODE 00b 10b 00b

KTXCMD

LINE

STATE JKSE0 J

CLK

DATA

[7:0]

TXCMD

(REGW) LINESTATE J LINE STATE K SE0 J

DIR

STP

NXT

OPMODE 00b 10b 00b

SUSPEND

LINE

STATE J KSE0 J

004aaa715

FS or LS host (XCVRSELECT = 01b (FS)

or 10b (LS), DPPULLDOWN = 1b,

DMPULLDOWN = 1b, TERMSELECT = 1b)

FS or LS peripheral (XCVRSELECT = 01b (FS)

or 10b (LS), DPPULLDOWN = 0b, TERMSELECT = 1b)

USB signals

(only FS is shown)

IDLE SUSPEND RESUME K EOP IDLE

Product data sheet Rev. 01 — 19 October 2006 37 of 78

NXP Semiconductors ISP1505A; ISP1505C

ULPI HS USB host and peripheral transceiver

The sequence of events related to a host and a peripheral, both with ISP1505, is as

follows:

1. High-speed idle: Initially, the host and the peripheral are idle. The host has its 15 kΩ

pull-down resistors enabled (DP_PULLDOWN and DM_PULLDOWN are set to 1b)

and 45 Ω terminations enabled (TERMSELECT is set to 0b). The peripheral has its

45 Ω terminations enabled (TERMSELECT is set to 0b).

2. Full-speed suspend: When the peripheral sees no bus activity for 3 ms, it enters the

suspend state. The peripheral link places the ISP1505 into full-speed mode

(XCVRSELECT is set to 01b), removes 45 Ω terminations, and enables the 1.5 kΩ

pull-up resistor on DP (TERMSELECT is set to 1b). The peripheral link then places

the ISP1505 into low-power mode by setting SUSPENDM, causing the ISP1505 to

draw only suspend current. The host also changes the ISP1505 to full-speed

(XCVRSELECT is set to 01b), removes 45 Ω terminations (TERMSELECT is set to

1b), and then may or may not be powered down.

3. Resume K: When the host wants to wake up the peripheral, it sets OPMODE to 10b

and transmits a full-speed K for at least 20 ms. The peripheral link sees the resume K

(10b) on LINESTATE, and asserts STP to wake up the ISP1505.

4. High-speed trafﬁc: The host link sets high-speed (XCVRSELECT is set to 00b) and

enables its 45 Ω terminations (TERMSELECT is set to 0b). The peripheral link sees

SE0 on LINESTATE and also sets high-speed (XCVRSELECT is set to 00b), and

enables its 45 Ω terminations (TERMSELECT is set to 0b). The host link sets

OPMODE to 00b for normal high-speed operation.

Product data sheet Rev. 01 — 19 October 2006 38 of 78

NXP Semiconductors ISP1505A; ISP1505C

ULPI HS USB host and peripheral transceiver

Timing is not to scale.

Fig 15. High-speed suspend and resume

DATA

[7:0]

TXCMD

NOPID K...

TXCMD

(REGW)

DIR

STP

NXT

MODE 00b 10b 00b

KTXCMD

(REGW)

CLK

DATA

[7:0]

TXCMD

(REGW) LINESTATE J LINESTATE K SE0 TXCMD

(REGW)

DIR

STP

NXT

MODE 00b 10b 00b

SUSPEND

LINE

STATE

004aaa717

ULPI HS host (DPPULLDOWN = 1b,

DMPULLDOWN = 1b)

ULPI HS peripheral (DPPULLDOWN = 0b)

USB signals

HS IDLE FS SUSPEND RESUME K

TXCMD

(REGW)

HS IDLE

XCVR

SELECT 00b 01b 00b

TERM

SELECT

LINE

STATE

!SQUELCH

(01b) FS J (01b) !SQUELCH

(01b)

SQUELCH (00b)

FS K (10b)

XCVR

SELECT 00b 01b 00b

TERM

SELECT

!SQUELCH

(01b) SQUELCH

(00b) FS J (01b) !SQUELCH

(01b)

SQUELCH (00b)

FS K (10b)

SQUELCH

(00b)

Product data sheet Rev. 01 — 19 October 2006 39 of 78

NXP Semiconductors ISP1505A; ISP1505C

ULPI HS USB host and peripheral transceiver

9.10.3 Remote wake-up

The ISP1505 supports peripherals that initiate remote wake-up resume. When placed into

USB suspend, the peripheral link remembers at what speed it was originally operating.

Depending on the original speed, the link follows one of the protocols detailed here. In

Figure 16, timing is not to scale, and not all RXCMD LINESTATE updates are shown.

The sequence of events related to a host and a peripheral, both with ISP1505, is as

follows:

1. Both the host and the peripheral are assumed to be in low-power mode.

2. The peripheral begins remote wake-up by re-enabling its clock and setting its

SUSPENDM bit to 1b.

3. The peripheral begins driving K on the bus to signal resume. Note that the peripheral

link must assume that LINESTATE is K (01b) while transmitting because it will not

receive any RXCMDs.

4. The host recognizes the resume, re-enables its clock and sets its SUSPENDM bit.

5. The host takes over resume driving within 1 ms of detecting the remote wake-up.

6. The peripheral stops driving resume.

7. The peripheral sees the host continuing to drive the resume.

8. The host stops driving resume and the ISP1505 automatically adds the EOP to the

end of the resume. The peripheral recognizes the EOP as the end of resume.

9. Both the host and the peripheral revert to normal operation by writing 00b to

OPMODE. If the host or the peripheral was previously in high-speed mode, it must

revert to high-speed before the SE0 of the EOP is completed. This can be achieved

by writing XCVRSELECT = 00b and TERMSELECT = 0b after LINESTATE indicates

SE0.

Product data sheet Rev. 01 — 19 October 2006 40 of 78

NXP Semiconductors ISP1505A; ISP1505C

ULPI HS USB host and peripheral transceiver

9.11 No automatic SYNC and EOP generation (optional)

This setting allows the link to turn off the automatic SYNC and EOP generation, and must

be used for high-speed packets only. It is provided for backward compatibility with legacy

controllers that include SYNC and EOP bytes in the data payload when transmitting

packets. The ISP1505 will not automatically generate the SYNC and EOP patterns when

OPMODE[1:0] is set to 11b. The ISP1505 will still NRZI encode data and perform bit

stufﬁng. An example of a sequence is shown in Figure 17. The link must always send

packets using the TXCMD (NOPID) type. The ISP1505 does not provide a mechanism to

control bit stufﬁng in individual bytes, but will automatically turn off bit stufﬁng for EOP

when STP is asserted with data set to FEh. If data is set to 00h when STP is asserted, the

Timing is not to scale.

Fig 16. Remote wake-up from low-power mode

DATA

[7:0]

LINESTATE TXCMD

REGW TXCMD

REGW

00h

TXCMD

NOPID

DIR

STP

NXT

XCVR

SELECT 01b (FS), 10b (LS) 00b (HS only)

TERM

SELECT

MODE 10b 00b

DATA

[7:0]

LINESTATE TXCMD

REGW RXCMD

00h

TXCMD

NOPID RXCMD RXCMD TXCMD

REGW

DIR

STP

NXT

XCVR

SELECT 00b (HS), 01b (FS), 10b (LS)

00b (HS only)

TERM

SELECT

MODE 10b 00b

ULPI host

ULPI peripheral

004aaa718

0b (HS only)

Product data sheet Rev. 01 — 19 October 2006 41 of 78

NXP Semiconductors ISP1505A; ISP1505C

ULPI HS USB host and peripheral transceiver

PHY will not transmit any EOP. The ISP1505 will also detect if the PID byte is A5h,

indicating an SOF packet, and automatically send a long EOP when STP is asserted. To

transmit chirp and resume signaling, the link must set OPMODE[1:0] to 10b.

9.12 On-The-Go operations

On-The-Go (OTG) is a supplement to

Universal Serial Bus Speciﬁcation Rev. 2.0

that

allows a portable USB device to assume the role of a limited USB host by deﬁning

improvements, such as a small connector and low power. Non-portable devices, such as

standard hosts and embedded hosts, can also beneﬁt from OTG features.

The ISP1505 OTG PHY is designed to support all the tasks speciﬁed in the OTG

supplement. The ISP1505 provides the front-end analog support for Host Negotiation

Protocol (HNP) and Session Request Protocol (SRP) for dual-role devices. The

supporting components include:

•Voltage comparators

–A_VBUS_VLD

–SESS_VLD (session valid, can be used for both A-session and B-session valid)

–SESS_END (session end)

•Pull-up and pull-down resistors on DP and DM

•Charge and discharge resistors on VBUS

For complete OTG support, the system designer must add a VBUS power supply and

detect the value on the ID pin of the USB cable. This is not provided on the ISP1505.

The following subsections describe how to use the ISP1505 OTG components.

Fig 17. Transmitting USB packets without the automatic SYNC and EOP generation

CLOCK

DATA

[7:0] TXCMD 00h 00h 00h 80h PID D1 D2 D3 ... ... DN − 1 FEh

DIR

STP

NXT

ULPI signals

VALID

READY

TXBIT

STUFF

ENABLE

DP,

DM IDLE SYNC PID IDLE

EOP

DATA PAYLOAD

004aaa719

UTMI+ equivalent

signals

USB bus

Product data sheet Rev. 01 — 19 October 2006 42 of 78

NXP Semiconductors ISP1505A; ISP1505C

ULPI HS USB host and peripheral transceiver

9.12.1 OTG comparators

The ISP1505 provides comparators that conform to

On-The-Go Supplement to the

USB 2.0 Speciﬁcation Rev. 1.2

requirements of VA_VBUS_VLD, VA_SESS_VLD, VB_SESS_VLD

and VB_SESS_END. In this data sheet, VA_SESS_VLD and VB_SESS_VLD are combined into

VB_SESS_VLD. Comparators are described in Section 7.6. Changes in comparator values

are communicated to the link by RXCMDs as described in Section 9.5.2.2. Control over

comparators is described in Section 10.1.5 to Section 10.1.8.

9.12.2 Pull-up and pull-down resistors

The USB resistors on DP and DM can be used to initiate data-line pulsing SRP. The link

must set the required bus state using mode settings given in Table 7.

9.12.3 VBUS charge and discharge resistors

A pull-up resistor, RUP(VBUS), is provided to perform VBUS pulsing SRP. A B-device is

allowed to charge VBUS above the session valid threshold to request the host to turn on

the VBUS power.

A pull-down resistor, RDN(VBUS), is provided for a B-device to discharge VBUS. This is done

whenever the A-device turns off the VBUS power; the B-device can use the pull-down

resistor to ensure VBUS is below VB_SESS_END before starting a session.

For details, refer to

On-The-Go Supplement to the USB 2.0 Speciﬁcation Rev. 1.2

9.13 Serial modes

The ISP1505 supports both 6-pin serial mode and 3-pin serial mode, controlled by

bits 6PIN_FSLS_SERIAL and 3PIN_FSLS_SERIAL of the Interface Control register. For

details, refer to

UTMI+ Low Pin Interface (ULPI) Speciﬁcation Rev. 1.1

, Section 3.10.

Figure 18 and Figure 19 provide examples of 6-pin serial mode and 3-pin serial mode,

respectively.

Product data sheet Rev. 01 — 19 October 2006 43 of 78

NXP Semiconductors ISP1505A; ISP1505C

ULPI HS USB host and peripheral transceiver

Fig 18. Example of transmit followed by receive in 6-bit serial mode

DATA0

(TX_ENABLE)

DATA1

(TX_DAT)

DATA2

(TX_SE0)

DATA4

(RX_DP)

DATA5

(RX_DM)

DATA6

(RX_RCV)

SYNC DATA EOP

TRANSMIT RECEIVE

SYNC DATA EOP

004aaa692

Fig 19. Example of transmit followed by receive in 3-bit serial mode

DATA0

(TX_ENABLE)

DATA1

(TX_DAT/

RX_RCV)

DATA2

(TX_SE0/

RX_SE0)

004aaa693

SYNC DATA EOP

TRANSMIT RECEIVE

SYNC DATA EOP

Product data sheet Rev. 01 — 19 October 2006 44 of 78

NXP Semiconductors ISP1505A; ISP1505C

ULPI HS USB host and peripheral transceiver

9.14 Aborting transfers

The ISP1505 supports aborting transfers on the ULPI bus. For details, refer to

UTMI+ Low

Pin Interface (ULPI) Speciﬁcation Rev. 1.1

, Section 3.8.4.

9.15 Avoiding contention on the ULPI data bus

Because the ULPI data bus is bidirectional, avoid situations in which both the link and the

PHY simultaneously drive the data bus.

The following points must be considered while implementing the data bus drive control on

the link.

After power-up and clock stabilization, default states are as follows:

•The ISP1505 drives DIR to LOW.

•The data bus is input to the ISP1505.

•The ULPI link data bus is output, with all data bus lines driven to LOW.

When the ISP1505 wants to take control of the data bus to initiate a data transfer, it

changes the DIR value from LOW to HIGH.

At this point, the link must disable its output buffers. This needs to be as fast as possible

so the link must use a combinational path from DIR.

The ISP1505 will not immediately enable its output buffers, but will delay the enabling of

its buffers until the next clock edge, avoiding bus contention.

When the data transfer is no longer required by the ISP1505, it changes DIR from HIGH to

LOW and starts to immediately turn off its output drivers. The link senses the change of

DIR from HIGH to LOW, but delays enabling its output buffers for one CLOCK cycle,

avoiding data bus contention.

Product data sheet Rev. 01 — 19 October 2006 45 of 78

NXP Semiconductors ISP1505A; ISP1505C

ULPI HS USB host and peripheral transceiver

10. Register map

[1] Read (R): A register can be read. Read-only if this is the only mode given.

[2] Write (W): The pattern on the data bus will be written over all bits of a register.

[3] Set (S): The pattern on the data bus is OR-ed with and written to a register.

[4] Clear (C): The pattern on the data bus is a mask. If a bit in the mask is set, then the corresponding register bit will be set to zero

(cleared).

10.1 Immediate register set

10.1.1 Vendor ID and Product ID registers

10.1.1.1 Vendor ID Low register

Table 16 shows the bit description of the register.

Table 15. Register map overview

Field name Size

(bits Address (6 bits) References

R[1] W[2] S[3] C[4]

Immediate register set

Vendor ID Low register 8 00h - - - Section 10.1.1 on page 45

Vendor ID High register 8 01h - - -

Product ID Low register 8 02h - - -

Product ID High register 8 03h - - -

Function Control register 8 04h to 06h 04h 05h 06h Section 10.1.2 on page 46

Interface Control register 8 07h to 09h 07h 08h 09h Section 10.1.3 on page 47

OTG Control register 8 0Ah to 0Ch 0Ah 0Bh 0Ch Section 10.1.4 on page 48

USB Interrupt Enable Rising Edge

USB Interrupt Enable Falling Edge

USB Interrupt Status register 8 13h - - - Section 10.1.7 on page 50

USB Interrupt Latch register 8 14h - - - Section 10.1.8 on page 51

Debug register 8 15h - - - Section 10.1.9 on page 51

Scratch register 8 16h to 18h 16h 17h 18h Section 10.1.10 on page 52

Reserved (do not use) - 19h to 2Eh Section 10.1.11 on page 52

Access extended register set 8 - 2Fh - - Section 10.1.12 on page 52

Vendor-speciﬁc registers 8 30h to 3Ch Section 10.1.13 on page 52

Power Control register 8 3Dh to 3Fh Section 10.1.14 on page 52

Extended register set Address (8 bits) Section 10.2 on page 53

Maps to immediate register set above 8 00h to 3Fh -

Reserved (do not use) 8 40h to FFh -

Table 16. Vendor ID Low register (address R = 00h) bit description

Bit Symbol Access Value Description

7 to 0 VENDOR_ID_

LOW[7:0] R CCh Vendor ID Low: Lower byte of the NXP vendor ID supplied by USB-IF; has

a ﬁxed value of CCh

Product data sheet Rev. 01 — 19 October 2006 46 of 78

NXP Semiconductors ISP1505A; ISP1505C

ULPI HS USB host and peripheral transceiver

10.1.1.2 Vendor ID High register

The bit description of the register is given in Table 17.

10.1.1.3 Product ID Low register

The bit description of the Product ID Low register is given in Table 18.

10.1.1.4 Product ID High register

The bit description of the register is given in Table 19.

10.1.2 Function Control register

This register controls UTMI function settings of the PHY. The bit allocation of the register

is given in Table 20.

Table 17. Vendor ID High register (address R = 01h) bit description

Bit Symbol Access Value Description

7 to 0 VENDOR_ID_

HIGH[7:0] R 04h Vendor ID High: Upper byte of the NXP vendor ID supplied by USB-IF;

has a ﬁxed value of 04h

Table 18. Product ID Low register (address R = 02h) bit description

Bit Symbol Access Value Description

7 to 0 PRODUCT_ID_

LOW[7:0] R 05h Product ID Low: Lower byte of the NXP product ID number; has a ﬁxed

value of 05h

Table 19. Product ID High register (address R = 03h) bit description

Bit Symbol Access Value Description

7 to 0 PRODUCT_ID_

HIGH[7:0] R 15h Product ID High: Upper byte of the NXP product ID number; has a

ﬁxed value of 15h

Table 20. Function Control register (address R = 04h to 06h, W = 04h, S = 05h, C = 06h) bit allocation

Bit 7 6 5 4 3 2 1 0

Symbol reserved SUSPENDM RESET OPMODE[1:0] TERM

SELECT XCVRSELECT[1:0]

Reset 0 1000001

Access R/W/S/C R/W/S/C R/W/S/C R/W/S/C R/W/S/C R/W/S/C R/W/S/C R/W/S/C

Product data sheet Rev. 01 — 19 October 2006 47 of 78

NXP Semiconductors ISP1505A; ISP1505C

ULPI HS USB host and peripheral transceiver

10.1.3 Interface Control register

The Interface Control register enables alternative interfaces. All of these modes are

optional features provided for legacy link cores. Setting more than one of these ﬁelds

results in undeﬁned behavior. Table 22 provides the bit allocation of the register.

Table 21. Function Control register (address R = 04h to 06h, W = 04h, S = 05h, C = 06h) bit description

Bit Symbol Description

7 - reserved

6 SUSPENDM Suspend LOW: Active LOW PHY suspend.

Places the PHY into low-power mode. The PHY will power down all blocks, except the

full-speed receiver, OTG comparators and ULPI interface pins.

To come out of low-power mode, the link must assert STP. The PHY will automatically clear

this bit when it exits low-power mode.

0b — Low-power mode

1b — Powered (default)

5 RESET Reset: Active HIGH transceiver reset.

After the link sets this bit, the PHY will assert DIR and reset the digital core. This does not

reset the ULPI interface or the ULPI register set.

When reset is completed, the PHY will de-assert DIR and automatically clear this bit,

followed by an RXCMD update to the link.

0b — Do not reset (default)

1b — Reset

The link must wait for DIR to de-assert before using the ULPI bus. Does not reset the ULPI

interface or the ULPI register set.

4 to 3 OPMODE[1:0] Operation Mode: Selects the required bit-encoding style during transmit.

00b — Normal operation (default)

01b — Non-driving

10b — Disable bit-stufﬁng and NRZI encoding

11b — Do not automatically add SYNC and EOP when transmitting; must be used only for

high-speed packets

2 TERMSELECT Termination Select: Controls the internal 1.5 kΩ full-speed pull-up resistor and 45 Ω

high-speed terminations. Control over bus resistors changes, depending on

XCVRSELECT[1:0], OPMODE[1:0], DP_PULLDOWN and DM_PULLDOWN, as shown in

Table 7.

1 to 0 XCVRSELECT[1:0] Transceiver Select: Selects the required transceiver speed.

00b — Enable the high-speed transceiver

01b — Enable the full-speed transceiver

10b — Enable the low-speed transceiver

11b — Enable the full-speed transceiver for low-speed packets (full-speed preamble is

automatically preﬁxed)

Table 22. Interface Control register (address R = 07h to 09h, W = 07h, S = 08h, C = 09h) bit allocation

Bit 7 6 5 4 3 2 1 0

Symbol INTF_

PROT_DIS IND_PASS

THRU IND_

COMPL reserved CLOCK_

SUSPENDM reserved 3PIN_

FSLS_

SERIAL

6PIN_

FSLS_

SERIAL

Reset 0000 0 000

Access R/W/S/C R/W/S/C R/W/S/C R/W/S/C R/W/S/C R/W/S/C R/W/S/C R/W/S/C

Product data sheet Rev. 01 — 19 October 2006 48 of 78

NXP Semiconductors ISP1505A; ISP1505C

ULPI HS USB host and peripheral transceiver

10.1.4 OTG Control register

This register controls various OTG functions of the ISP1505. The bit allocation of the OTG

Control register is given in Table 24.

Table 23. Interface Control register (address R = 07h to 09h, W = 07h, S = 08h, C = 09h) bit description

Bit Symbol Description

7 INTF_PROT_DIS Interface Protect Disable: Controls circuitry built into the ISP1505 to protect the ULPI

interface when the link 3-states STP and DATA[7:0]. When this bit is enabled, the

ISP1505 will automatically detect when the link stops driving STP.

0b — Enables the interface protect circuit (default). The ISP1505 attaches a weak

pull-up resistor on STP. If STP is unexpectedly HIGH, the ISP1505 attaches weak

pull-down resistors on DATA[7:0], protecting data inputs.

1b — Disables the interface protect circuit, detaches weak pull-down resistors on

DATA[7:0], and a weak pull-up resistor on STP.

6 IND_PASSTHRU Indicator Pass-through: The ISP1505 does not support the qualiﬁcation of an external

FAULT with the internal VA_VBUS_VLD comparator. Either a digital FAULT is input on the

VBUS/FAULT pin or the VBUS power is connected to the VBUS/FAULT pin, not both. This bit

must always be set to logic 1.

0b — Not supported.

1b — The complement output signal is not qualiﬁed with the internal A_VBUS_VLD

comparator. The link must always set this bit to logic 1.

5 IND_COMPL Indicator Complement: Informs the PHY to invert the FAULT input signal, generating

the complement output. For details, see Section 9.5.2.2.

0b — The ISP1505 will not invert the FAULT signal (default).

1b — The ISP1505 will invert the FAULT signal.

4 - reserved

3 CLOCK_SUSPENDM Clock Suspend LOW: Active LOW clock suspend.

Powers down the internal clock circuitry only. By default, the clock will not be powered in

6-pin serial mode or 3-pin serial mode.

Valid only in 6-pin serial mode and 3-pin serial mode. Valid only when SUSPENDM is set

to logic 1, otherwise this bit is ignored.

0b — Clock will not be powered in 3-pin or 6-pin serial mode.

1b — Clock will be powered in 3-pin and 6-pin serial modes.

2 - reserved

1 3PIN_FSLS_SERIAL 3-Pin Full-Speed Low-Speed Serial Mode: Changes the ULPI interface to a 3-bit serial

interface. The PHY will automatically clear this bit when 3-pin serial mode is exited.

0b — Full-speed or low-speed packets are sent using the parallel interface.

1b — Full-speed or low-speed packets are sent using the 3-pin serial interface.

0 6PIN_FSLS_SERIAL 6-Pin Full-Speed Low-Speed Serial Mode: Changes the ULPI interface to a 6-bit serial

interface. The PHY will automatically clear this bit when 6-pin serial mode is exited.

0b — Full-speed or low-speed packets are sent using the parallel interface.

1b — Full-speed or low-speed packets are sent using the 6-pin serial interface.

Table 24. OTG Control register (address R = 0Ah to 0Ch, W = 0Ah, S = 0Bh, C = 0Ch) bit allocation

Bit 76543210

Symbol USE_EXT_

VBUS_IND DRV_

VBUS_EXT DRV_

VBUS CHRG_

VBUS DISCHRG_

VBUS DM_PULL

DOWN DP_PULL

DOWN reserved

Reset 00000110

Access R/W/S/C R/W/S/C R/W/S/C R/W/S/C R/W/S/C R/W/S/C R/W/S/C R/W/S/C

Product data sheet Rev. 01 — 19 October 2006 49 of 78

NXP Semiconductors ISP1505A; ISP1505C

ULPI HS USB host and peripheral transceiver

10.1.5 USB Interrupt Enable Rising Edge register

The bits in this register enable interrupts and RXCMDs to be sent when the corresponding

bits in the USB Interrupt Status register change from logic 0 to logic 1. By default, all

transitions are enabled. Table 26 shows the bit allocation of the register.

Table 25. OTG Control register (address R = 0Ah to 0Ch, W = 0Ah, S = 0Bh, C = 0Ch) bit description

Bit Symbol Description

7 USE_EXT_

VBUS_IND Use External VBUS Indicator: Informs the PHY to use an external VBUS overcurrent indicator.

0b — Use the internal OTG comparator.

1b — Use the external VBUS valid indicator signal input from the FAULT pin.

6 DRV_VBUS_EXT Drive VBUS External: Controls the external VBUS supply through the RESET_N/PSW_N pin.

0b — Do not drive PSW_N to LOW, disabling VBUS.

1b — Drive PSW_N to LOW, enabling VBUS.

5 DRV_VBUS Drive VBUS: Signals the ISP1505 to drive 5 V on VBUS. If DRV_VBUS_EXT is set to logic 1,

then setting DRV_VBUS is optional.

4 CHRG_VBUS Charge VBUS: Charges VBUS through a resistor. Used for the VBUS pulsing SRP. The link must

ﬁrst check that VBUS is discharged (see the DISCHRG_VBUS bit), and that both the DP and

DM data lines have been LOW (SE0) for 2 ms.

0b — Do not charge VBUS

1b — Charge VBUS

3 DISCHRG_VBUS Discharge VBUS: Discharges VBUS through a resistor. If the link sets this bit to logic 1, it waits

for an RXCMD indicating that SESS_END has changed from 0 to 1, and then resets this bit to 0

to stop the discharge.

0b — Do not discharge VBUS

1b — Discharge VBUS

2 DM_PULLDOWN DM Pull Down: Enables the 15 kΩ pull-down resistor on DM.

0b — Pull-down resistor is not connected to DM.

1b — Pull-down resistor is connected to DM.

1 DP_PULLDOWN DP Pull Down: Enables the 15 kΩ pull-down resistor on DP.

0b — Pull-down resistor is not connected to DP.

1b — Pull-down resistor is connected to DP.

0 - reserved; writing logic 1 will give undeﬁned results

Table 26. USB Interrupt Enable Rising Edge register (address R = 0Dh to 0Fh, W = 0Dh, S = 0Eh, C = 0Fh) bit

allocation

Bit 76543210

Symbol reserved SESS_

END_R SESS_

VALID_R VBUS_

VALID_R HOST_

DISCON_R

Reset 00011111

Access R/W/S/C R/W/S/C R/W/S/C R/W/S/C R/W/S/C R/W/S/C R/W/S/C R/W/S/C

Product data sheet Rev. 01 — 19 October 2006 50 of 78

NXP Semiconductors ISP1505A; ISP1505C

ULPI HS USB host and peripheral transceiver

10.1.6 USB Interrupt Enable Falling Edge register

The bits in this register enable interrupts and RXCMDs to be sent when the corresponding

bits in the USB Interrupt Status register change from logic 1 to logic 0. By default, all

transitions are enabled. See Table 28.

10.1.7 USB Interrupt Status register

This register (see Table 30) indicates the current value of the interrupt source signal.

Table 27. USB Interrupt Enable Rising Edge register (address R = 0Dh to 0Fh, W = 0Dh, S = 0Eh, C = 0Fh) bit

description

Bit Symbol Description

7 to 4 - reserved

3 SESS_END_R Session End Rise: Enables interrupts and RXCMDs for logic 0 to logic 1 transitions on

SESS_END.

2 SESS_VALID_R Session Valid Rise: Enables interrupts and RXCMDs for logic 0 to logic 1 transitions on

SESS_VLD.

1 VBUS_VALID_R VBUS Valid Rise: Enables interrupts and RXCMDs for logic 0 to logic 1 transitions on

A_VBUS_VLD.

0 HOST_DISCON_

RHost Disconnect Rise: Enables interrupts and RXCMDs for logic 0 to logic 1 transitions on

HOST_DISCON.

Table 28. USB Interrupt Enable Falling Edge register (address R = 10h to 12h, W = 10h, S = 11h, C = 12h) bit

allocation

Bit 76543210

Symbol reserved SESS_

END_F SESS_

VALID_F VBUS_

VALID_F HOST_

DISCON_F

Reset 00011111

Access R/W/S/C R/W/S/C R/W/S/C R/W/S/C R/W/S/C R/W/S/C R/W/S/C R/W/S/C

Table 29. USB Interrupt Enable Falling Edge register (address R = 10h to 12h, W = 10h, S = 11h, C = 12h) bit

description

Bit Symbol Description

7 to 4 - reserved

3 SESS_END_F Session End Fall: Enables interrupts and RXCMDs for logic 1 to logic 0 transitions on

SESS_END.

2 SESS_VALID_F Session Valid Fall: Enables interrupts and RXCMDs for logic 1 to logic 0 transitions on

SESS_VLD.

1 VBUS_VALID_F VBUS Valid Fall: Enables interrupts and RXCMDs for logic 1 to logic 0 transitions on

A_VBUS_VLD.

0 HOST_DISCON_

FHost Disconnect Fall: Enables interrupts and RXCMDs for logic 1 to logic 0 transitions on

HOST_DISCON.

Table 30. USB Interrupt Status register (address R = 13h) bit allocation

Bit 76543210

Symbol reserved SESS_

END SESS_

VALID VBUS_

VALID HOST_

DISCON

Reset XXX00000

Access RRRRRRRR

Product data sheet Rev. 01 — 19 October 2006 51 of 78

NXP Semiconductors ISP1505A; ISP1505C

ULPI HS USB host and peripheral transceiver

10.1.8 USB Interrupt Latch register

The bits of the USB Interrupt Latch register are automatically set by the ISP1505 when an

unmasked change occurs on the corresponding interrupt source signal. The ISP1505 will

automatically clear all bits when the link reads this register, or when the PHY enters

low-power mode.

Remark: It is optional for the link to read this register when the clock is running because

all signal information will automatically be sent to the link through the RXCMD byte.

The bit allocation of this register is given in Table 32.

10.1.9 Debug register

The bit allocation of the Debug register is given in Table 34. This register indicates the

current value of signals useful for debugging.

Table 31. USB Interrupt Status register (address R = 13h) bit description

Bit Symbol Description

7 to 4 - reserved

3 SESS_END Session End: Reﬂects the current value of the session end voltage comparator.

2 SESS_VALID Session Valid: Reﬂects the current value of the session valid voltage comparator.

1 VBUS_VALID VBUS Valid: Reﬂects the current value of the VBUS valid voltage comparator.

0 HOST_DISCON Host Disconnect: Reﬂects the current value of the host disconnect detector.

Table 32. USB Interrupt Latch register (address R = 14h) bit allocation

Bit 76543210

Symbol reserved SESS_

END_L SESS_

VALID_L VBUS_

VALID_L HOST_

DISCON_L

Reset 00000000

Access RRRRRRRR

Table 33. USB Interrupt Latch register (address R = 14h) bit description

Bit Symbol Description

7 to 4 - reserved

3 SESS_END_L Session End Latch: Automatically set when an unmasked event occurs on SESS_END.

Cleared when this register is read.

2 SESS_VALID_L Session Valid Latch: Automatically set when an unmasked event occurs on SESS_VLD.

Cleared when this register is read.

1 VBUS_VALID_L VBUS Valid Latch: Automatically set when an unmasked event occurs on A_VBUS_VLD.

Cleared when this register is read.

0 HOST_DISCON_L Host Disconnect Latch: Automatically set when an unmasked event occurs on

HOST_DISCON. Cleared when this register is read.

Table 34. Debug register (address R = 15h) bit allocation

Bit 76543210

Symbol reserved LINE

STATE1 LINE

STATE0

Reset 00000000

Access RRRRRRRR

Product data sheet Rev. 01 — 19 October 2006 52 of 78

NXP Semiconductors ISP1505A; ISP1505C

ULPI HS USB host and peripheral transceiver

10.1.10 Scratch register

Table 36 shows the bit description of the Scratch register. It is an empty register for testing

purposes.

10.1.11 Reserved

Registers 19h to 2Eh are not implemented. Operating on these addresses will have no

effect on the PHY.

10.1.12 Access extended register set

Address 2Fh does not contain register data. Instead it links to the extended register set.

The immediate register set maps to the lower end of the extended register set.

10.1.13 Vendor-speciﬁc registers

Addresses 30h to 3Fh contains vendor-speciﬁc registers.

10.1.14 Power Control register

Table 37 provides the bit allocation of the Power Control register.

Table 35. Debug register (address R = 15h) bit description

Bit Symbol Description

7 to 2 - reserved

1 LINESTATE1 Line State 1: Contains the current value of LINESTATE 1

0 LINESTATE0 Line State 0: Contains the current value of LINESTATE 0

Table 36. Scratch register (address R = 16h to 18h, W = 16h, S = 17h, C = 18h) bit description

Bit Symbol Access Value Description

7 to 0 SCRATCH

[7:0] R/W/S/C 00h Scratch: This is an empty register byte for testing purposes. Software

can read, write, set and clear this register; and the functionality of the

PHY will not be affected.

Table 37. Power Control register (address R = 3Dh to 3Fh, W = 3Dh, S = 3Eh, C = 3Fh) bit allocation

Bit 76543210

Symbol reserved BVALID_

FALL BVALID_

RISE reserved IGNORE_

RESET

Reset 00000000

Access R/W/S/C R/W/S/C R/W/S/C R/W/S/C R/W/S/C R/W/S/C R/W/S/C R/W/S/C

Product data sheet Rev. 01 — 19 October 2006 53 of 78

NXP Semiconductors ISP1505A; ISP1505C

ULPI HS USB host and peripheral transceiver

10.2 Extended register set

Addresses 00h to 3Fh of the extended register set directly map to the immediate set. This

means a read, write, set or clear operation to these extended addresses will operate on

the immediate register set.

Addresses 40h to FFh are not implemented. Operating on these addresses will have no

effect on the PHY.

Table 38. Power Control register (address R = 3Dh to 3Fh, W = 3Dh, S = 3Eh, C = 3Fh) bit description

Bit Symbol Description

7 to 4 - reserved; the link must never write logic 1 to these bits.

3 BVALID_FALL BVALID Fall: Enables RXCMDs for HIGH-to-LOW transitions on BVALID. When BVALID

changes from HIGH to LOW, the ISP1505 will send an RXCMD to the link with the ALT_INT

bit set to logic 1.

This bit is optional and is not necessary for OTG devices. The session valid comparator must

be used instead.

2 BVALID_RISE BVALID Rise: Enables RXCMDs for LOW-to-HIGH transitions on BVALID. When BVALID

changes from LOW to HIGH, the ISP1505 will send an RXCMD to the link with the ALT_INT

bit set to logic 1.

This bit is optional and is not necessary for OTG devices. The session valid comparator must

be used instead.

1 - reserved

0 IGNORE_RESET Ignore Reset: Selects between the RESET_N and PSW_N functions of the

RESET_N/PSW_N pin. The link must set this bit to logic 1, if PSW_N is used in a ganged

mode conﬁguration.

0b — The RESET_N/PSW_N pin behaves as an active-LOW reset input (RESET_N). This is

the default setting.

1b — The RESET_N/PSW_N pin behaves as an active-LOW power switch output (PSW_N).

Product data sheet Rev. 01 — 19 October 2006 54 of 78

NXP Semiconductors ISP1505A; ISP1505C

ULPI HS USB host and peripheral transceiver

11. ElectroStatic Discharge (ESD)

11.1 ESD protection

The pins that are connected to the USB connector (DP, DM, VBUS and GND) have a

minimum of ±4 kV ESD protection. Capacitors 0.1 µF and 1 µF must be connected in

parallel from VBUS to GND to achieve this ±4 kV ESD protection (see Figure 20).

Remark: Capacitors 0.1 µF and 1 µF are also required by

Universal Serial Bus

Speciﬁcation Rev. 2.0

. For details on the requirements for CVBUS, see Section 16.

11.2 ESD test conditions

A detailed report on test setup and results is available on request.

Fig 20. Human body ESD test model

1500 Ω

1 MΩ

HIGH VOLTAGE

DC SOURCE 0.1 µF1 µF

VBUS

DEVICE UNDER

TEST

100 pF storage

capacitor

charge current

limit resistor discharge

resistance

GND

004aaa881

Product data sheet Rev. 01 — 19 October 2006 55 of 78

NXP Semiconductors ISP1505A; ISP1505C

ULPI HS USB host and peripheral transceiver

12. Limiting values

[1] Equivalent to discharging a 100 pF capacitor through a 1.5 kΩ resistor (Human Body Model JESD22-A114D).

13. Recommended operating conditions

[1] VCC(I/O) should be less than or equal to VCC.

Table 39. Limiting values

In accordance with the Absolute Maximum Rating System (IEC 60134).

Symbol Parameter Conditions Min Max Unit

VCC supply voltage −0.5 +4.6 V

VCC(I/O) input/output supply voltage −0.5 +4.6 V

VIinput voltage onpins CLOCK,STP, DATA[7:0]and

RESET_N/PSW_N −0.5 VCC(I/O) + 0.5 V V

on pin VBUS/FAULT −0.5 +6.0 V

on pin XTAL1 −0.5 +2.5 V

VESD electrostatic discharge

voltage on pins DP, DM, VBUS and GND;

ILI <1µA[1] −4+4 kV

on all other pins; ILI < 1 µA−2+2 kV

Ilu latch-up current −100 +100 mA

Vlu latch-up voltage - 4.6 V

Tstg storage temperature −40 +125 °C

Tjjunction temperature −40 +125 °C

Table 40. Recommended operating conditions

Symbol Parameter Conditions Min Typ Max Unit

VCC supply voltage 3.0 3.3 3.6 V

VCC(I/O) input/output supply voltage [1] 1.65 - 3.6 V

VIinput voltage on pins CLOCK, STP, DATA[7:0]

and RESET_N/PSW_N 0- V

CC(I/O) V

on pin VBUS/FAULT 0 - 5.5 V

on pins DP and DM 0 - 3.6 V

on pin XTAL1 0 - 1.95 V

Tamb ambient temperature −40 +25 +85 °C

Product data sheet Rev. 01 — 19 October 2006 56 of 78

NXP Semiconductors ISP1505A; ISP1505C

ULPI HS USB host and peripheral transceiver

14. Static characteristics

[1] A continuous stream of 1 kB packets with minimum inter-packet gap and all data bits set to logic 0 for continuous toggling.

Table 41. Static characteristics: supply pins

= 3.0 V to 3.6 V; V

CC(I/O)

= 1.65 V to 3.6 V; T

amb

−

Cto+85

C; unless otherwise speciﬁed.

Typical values are at V

= 3.3 V; V

CC(I/O)

= 3.3 V; T

amb

= +25

C; unless otherwise speciﬁed.

Symbol Parameter Conditions Min Typ Max Unit

V(REG3V3) voltage on pin REG3V3 3.0 3.3 3.6 V

V(REG1V8) voltage on pin REG1V8 1.65 1.8 1.95 V

VPOR(trip) power-on reset trip

voltage 1.0 - 1.5 V

ICC supply current low-power mode; VBUS valid detector

disabled; 1.5 kΩ pull-up resistor on

pin DP disconnected

-3085µA

low-power mode; VBUS valid detector

disabled; 1.5 kΩ pull-up resistor on

pin DP connected

- 215 280 µA

full-speed idle; no USB activity - 10 - mA

high-speed idle; no USB activity - 19 - mA

full-speed continuous data transmit;

50 pF load on pins DP and DM [1] -15-mA

full-speed continuous data receive [1] -11-mA

high-speed continuous data transmit;

45 Ωload on pins DP and DM to ground [1] -48-mA

high-speed continuous data receive [1] -28-mA

ICC(I/O) supply current on

pin VCC(I/O)

static current; I/O pins are idle - - 1 µA

Table 42. Static characteristics: digital pins (CLOCK, DIR, STP, NXT, DATA[7:0], RESET_N/PSW_N)

= 3.0 V to 3.6 V; V

CC(I/O)

= 1.65 V to 3.6 V; T

amb

−

Cto+85

C; unless otherwise speciﬁed.

Typical values are at V

= 3.3 V; V

CC(I/O)

= 3.3 V; T

amb

= +25

C; unless otherwise speciﬁed.

Symbol Parameter Conditions Min Typ Max Unit

Input levels

VIL LOW-level input voltage - - 0.3 ×VCC(I/O) V

VIH HIGH-level input voltage 0.7 ×VCC(I/O) -- V

IIL LOW-level input current VI= 0 V - - 1 µA

IIH HIGH-level input current VI= VCC(I/O) --1µA

ILI input leakage current −1 +0.1 +1 µA

Output levels

VOL LOW-level output voltage IOL =−2 mA - - 0.4 V

VOH HIGH-level output voltage IOH = +2 mA VCC(I/O) −0.4 V - - V

IOH HIGH-level output current VO= VCC(I/O) −0.4 V −4.8 - - mA

IOL LOW-level output current VO= 0.4 V 4.2 - - mA

IOZ off-state output current 0 V < VO<V

CC(I/O) --1µA

Product data sheet Rev. 01 — 19 October 2006 57 of 78

NXP Semiconductors ISP1505A; ISP1505C

ULPI HS USB host and peripheral transceiver

Impedance

ZLload impedance 45 - 65 Ω

Pull-up and pull-down

Ipd pull-down current interface protect

enabled; DATA[7:0]

pins only; VI=V

CC(I/O)

25 50 90 µA

Ipu pull-up current interface protect

enabled; STP pin only;

VI=0V

−30 −50 −80 µA

Capacitance

Cin input capacitance pins STP, RESET_N,

CLOCK, DATA[7:0] - - 3.5 pF

Table 42. Static characteristics: digital pins (CLOCK, DIR, STP, NXT, DATA[7:0], RESET_N/PSW_N)

…continued

= 3.0 V to 3.6 V; V

CC(I/O)

= 1.65 V to 3.6 V; T

amb

−

Cto+85

C; unless otherwise speciﬁed.

Typical values are at V

= 3.3 V; V

CC(I/O)

= 3.3 V; T

amb

= +25

C; unless otherwise speciﬁed.

Symbol Parameter Conditions Min Typ Max Unit

Table 43. Static characteristics: pin VBUS/FAULT

= 3.0 V to 3.6 V; V

CC(I/O)

= 1.65 V to 3.6 V; T

amb

−

C to +85

C; unless otherwise speciﬁed.

Typical values are at V

= 3.3 V; V

CC(I/O)

= 3.3 V; T

amb

= +25

C; unless otherwise speciﬁed.

Applicable only when pin V

BUS

/FAULT is used as FAULT.

Symbol Parameter Conditions Min Typ Max Unit

Input levels

VIL LOW-level input voltage - - 0.8 V

VIH HIGH-level input voltage 2.0 - - V

IIL LOW-level input current VI= 0 V - - 1 µA

IIH HIGH-level input current VI= VCC(I/O) --1µA

Table 44. Static characteristics: analog I/O pins (DP, DM)

= 3.0 V to 3.6 V; V

CC(I/O)

= 1.65 V to 3.6 V; T

amb

−

Cto+85

C; unless otherwise speciﬁed.

Typical values are at V

= 3.3 V; V

CC(I/O)

= 3.3 V; T

amb

= +25

C; unless otherwise speciﬁed.

Symbol Parameter Conditions Min Typ Max Unit

Original USB transceiver (low-speed and full-speed)

Input levels (differential receiver)

VDI differential input sensitivity |VDP −VDM|0.2 - - V

VCM differential common mode voltage

range includes VDI range 0.8 - 2.5 V

Input levels (single-ended receivers)

VIL LOW-level input voltage - - 0.8 V

VIH HIGH-level input voltage 2.0 - - V

Output levels

VOL LOW-level output voltage pull-up on pin DP;

RL= 1.5 kΩto 3.6 V 0.0 0.18 0.3 V

VOH HIGH-level output voltage pull-down on pins DP and

DM; RL=15kΩto GND 2.8 3.2 3.6 V

Product data sheet Rev. 01 — 19 October 2006 58 of 78

NXP Semiconductors ISP1505A; ISP1505C

ULPI HS USB host and peripheral transceiver

[1] For high-speed USB and full-speed USB.

Termination

VTERM termination voltage for 1.5 kΩ pull-up resistor 3.0 - 3.6 V

Resistance

RUP(DP) pull-up resistance on pin DP 1425 1500 1575 Ω

High-speed USB transceiver

Input levels (differential receiver)

VHSSQ high-speed squelch detection

threshold voltage (differential

signal amplitude)

100 - 150 mV

VHSDSC high-speed disconnect detection

threshold voltage (differential

signal amplitude)

525 - 625 mV

VHSDI high-speed differential input

sensitivity |VDP −VDM|300 - - mV

VHSCM high-speed data signaling

common mode voltage range includes VDI range −50 - +500 mV

VHSOI high-speed idle level −10 - +10 mV

VHSOL high-speed data signaling

LOW-level voltage −10 - +10 mV

Output levels

VHSOH high-speed data signaling

HIGH-level voltage 360 - 440 mV

VCHIRPJ Chirp J level (differential voltage) 700 - 1100 mV

VCHIRPK Chirp K level (differential voltage) −900 - −500 mV

Leakage current

ILZ off-state leakage current −1- +1µA

Capacitance

Cin input capacitance pin to GND - - 5 pF

Resistance

RDN(DP) pull-down resistance on pin DP 14.25 15 15.75 kΩ

RDN(DM) pull-down resistance on pin DM 14.25 15 15.75 kΩ

Termination

ZO(drv)(DP) driver output impedance on pin DP steady-state drive [1] 40.5 45 49.5 Ω

ZO(drv)(DM) driver output impedance on

pin DM steady-state drive [1] 40.5 45 49.5 Ω

ZINP input impedance 10 - - MΩ

Table 44. Static characteristics: analog I/O pins (DP, DM)

…continued

= 3.0 V to 3.6 V; V

CC(I/O)

= 1.65 V to 3.6 V; T

amb

−

Cto+85

C; unless otherwise speciﬁed.

Typical values are at V

= 3.3 V; V

CC(I/O)

= 3.3 V; T

amb

= +25

C; unless otherwise speciﬁed.

Symbol Parameter Conditions Min Typ Max Unit

Product data sheet Rev. 01 — 19 October 2006 59 of 78

NXP Semiconductors ISP1505A; ISP1505C

ULPI HS USB host and peripheral transceiver

Table 45. Static characteristics: VBUS comparators

= 3.0 V to 3.6 V; V

CC(I/O)

= 1.65 V to 3.6 V; T

amb

−

Cto+85

C; unless otherwise speciﬁed.

Typical values are at V

= 3.3 V; V

CC(I/O)

= 3.3 V; T

amb

= +25

C; unless otherwise speciﬁed.

Symbol Parameter Conditions Min Typ Max Unit

VA_VBUS_VLD A-device VBUS valid voltage 4.4 4.5 4.65 V

VB_SESS_VLD B-device session valid voltage for A-device and

B-device 0.8 1.6 2.0 V

Vhys(B_SESS_VLD) B-devicesessionvalidhysteresis

voltage 70 140 200 mV

VB_SESS_END B-device session end voltage 0.2 0.5 0.8 V

Table 46. Static characteristics: VBUS resistors

= 3.0 V to 3.6 V; V

CC(I/O)

= 1.65 V to 3.6 V; T

amb

−

Cto+85

C; unless otherwise speciﬁed.

Typical values are at V

= 3.3 V; V

CC(I/O)

= 3.3 V; T

amb

= +25

C; unless otherwise speciﬁed.

Symbol Parameter Conditions Min Typ Max Unit

RUP(VBUS) pull-up resistance on

pin VBUS

connect to pin REG3V3 when

CHRG_VBUS is logic 1 281 680 - Ω

RDN(VBUS) pull-down resistance on

pin VBUS

connect to GND when

DISCHRG_VBUS is logic 1 656 850 - Ω

RI(idle)(VBUS) idle input resistance on

pin VBUS

40 57 80 kΩ

Table 47. Static characteristics: resistor reference

= 3.0 V to 3.6 V; V

CC(I/O)

= 1.65 V to 3.6 V; T

amb

−

Cto+85

C; unless otherwise speciﬁed.

Typical values are at V

= 3.3 V; V

CC(I/O)

= 3.3 V; T

amb

= +25

C; unless otherwise speciﬁed.

Symbol Parameter Conditions Min Typ Max Unit

VO(RREF) output voltage on pin RREF SUSPENDM is logic 1 - 1.22 - V

Product data sheet Rev. 01 — 19 October 2006 60 of 78

NXP Semiconductors ISP1505A; ISP1505C

ULPI HS USB host and peripheral transceiver

15. Dynamic characteristics

[1] RMS = Root Mean Square.

Table 48. Dynamic characteristics: reset and clock

= 3.0 V to 3.6 V; V

CC(I/O)

= 1.65 V to 3.6 V; T

amb

−

Cto+85

C; unless otherwise speciﬁed.

Typical values are at V

= 3.3 V; V

CC(I/O)

= 3.3 V; T

amb

= +25

C; unless otherwise speciﬁed.

Symbol Parameter Conditions Min Typ Max Unit

Reset

tW(POR) internal power-on reset pulse

width 0.2 - - µs

tw(REG1V8_H) REG1V8 HIGH pulse width 2 - - µs

tw(REG1V8_L) REG1V8 LOW pulse width 11 - - µs

tW(RESET_N) external RESET_N pulse width 200 - - ns

tPWRUP regulator start-up time 4.7 µF±20 % capacitor

each on pins REG1V8

and REG3V3

--1ms

Crystal or clock applied to XTAL1

fi(XTAL1) input frequency on pin XTAL1 ISP1505ABS - 19.2 - MHz

ISP1505CBS - 26 - MHz

tjit(i)(XTAL1)RMS RMS input jitter on pin XTAL1 ISP1505ABS [1] - - 200 ps

ISP1505CBS [1] - - 300 ps

∆fi(XTAL1) input frequency tolerance on

pin XTAL1 - 50 200 ppm

tr(XTAL1) rise time on pin XTAL1 only for square wave input - - 5 ns

tf(XTAL1) fall time on pin XTAL1 only for square wave input - - 5 ns

V(XTAL1)(p-p) peak-to-peak voltage on

pin XTAL1 only for square wave input 0.566 - 1.95 V

External clock input on CLOCK

fi(CLOCK) input frequency on pin CLOCK - 60 - MHz

tjit(i)(CLOCK)RMS RMS input jitter on pin CLOCK [1] - - 200 ps

∆fi(CLOCK) input frequency tolerance on

pin CLOCK - 50 200 ppm

δi(CLOCK) input clock duty cycle on

pin CLOCK 45 50 55 %

Output CLOCK characteristics

fo(CLOCK) output frequency on pin CLOCK active only when a crystal

or clock is input on

pin XTAL1

- 60 - MHz

tjit(o)(CLOCK)RMS RMS output jitter on pin CLOCK [1] - - 500 ps

δo(CLOCK) output clock duty cycle on

pin CLOCK 45 50 55 %

tstartup(PLL) PLL startup time - 650 - µs

tstartup(o)(CLOCK) output CLOCK start-up time measured from power

good or assertion of

pin STP

450 650 900 µs

Product data sheet Rev. 01 — 19 October 2006 61 of 78

NXP Semiconductors ISP1505A; ISP1505C

ULPI HS USB host and peripheral transceiver

Table 49. Dynamic characteristics: digital I/O pins

= 3.0 V to 3.6 V; V

CC(I/O)

= 1.65 V to 3.6 V; T

amb

−

C to +85

C; unless otherwise speciﬁed.

Typical values are at V

= 3.3 V; T

amb

= +25

C; unless otherwise speciﬁed.

Symbol Parameter Conditions Min Typ Max Unit

Output 60 MHz CLOCK, VCC(I/O) = 1.65 V to 1.95 V

tsu(DATA) DATA set-up time with respect to

the rising edge of pin CLOCK 20 pF total external load

per pin 5.7 - - ns

th(DATA) DATA hold time with respect to

the rising edge of pin CLOCK 20 pF total external load

per pin 0- - ns

td(DATA) DATA output delay with respect

to the rising edge of pin CLOCK 20 pF total external load

per pin - - 7.8 ns

tsu(STP) STP set-up time with respect to

the rising edge of pin CLOCK 20 pF total external load

per pin 4.5 - - ns

th(STP) STP hold time with respect to

the rising edge of pin CLOCK 20 pF total external load

per pin 0- - ns

td(DIR) DIR output delay with respect to

the rising edge of pin CLOCK 20 pF total external load

per pin - - 8.9 ns

td(NXT) NXT output delay with respect to

the rising edge of pin CLOCK 20 pF total external load

per pin - - 8.9 ns

Output 60 MHz CLOCK, VCC(I/O) = 3.0 V to 3.6 V

tsu(DATA) DATA set-up time with respect to

the rising edge of pin CLOCK 30 pF total external load

per pin 3.3 - - ns

th(DATA) DATA hold time with respect to

the rising edge of pin CLOCK 30 pF total external load

per pin 0.8 - - ns

td(DATA) DATA output delay with respect

to the rising edge of pin CLOCK 30 pF total external load

per pin - - 5.5 ns

tsu(STP) STP set-up time with respect to

the rising edge of pin CLOCK 30 pF total external load

per pin 3.4 - - ns

th(STP) STP hold time with respect to

the rising edge of pin CLOCK 30 pF total external load

per pin 0.8 - - ns

td(DIR) DIR output delay with respect to

the rising edge of pin CLOCK 30 pF total external load

per pin - - 6.6 ns

td(NXT) NXT output delay with respect to

the rising edge of pin CLOCK 30 pF total external load

per pin - - 6.6 ns

Input 60 MHz CLOCK, VCC(I/O) = 1.65 V to 1.95 V

tsu(DATA) DATA set-up time with respect to

the rising edge of pin CLOCK 10 pF total external load

per pin 4.9 4.4 - ns

th(DATA) DATA hold time with respect to

the rising edge of pin CLOCK 10 pF total external load

per pin 0- - ns

td(DATA) DATA output delay with respect

to the rising edge of pin CLOCK 10 pF total external load

per pin 9.2 5.2 - ns

tsu(STP) STP set-up time with respect to

the rising edge of pin CLOCK 10 pF total external load

per pin 3.5 3.4 - ns

th(STP) STP hold time with respect to

the rising edge of pin CLOCK 10 pF total external load

per pin 0- - ns

td(DIR) DIR output delay with respect to

the rising edge of pin CLOCK 10 pF total external load

per pin - 4.9 9.3 ns

td(NXT) NXT output delay with respect to

the rising edge of pin CLOCK 10 pF total external load

per pin - 4.9 9.3 ns

Product data sheet Rev. 01 — 19 October 2006 62 of 78

NXP Semiconductors ISP1505A; ISP1505C

ULPI HS USB host and peripheral transceiver

Input 60 MHz CLOCK, VCC(I/O) = 3.0 V to 3.6 V

tsu(DATA) DATA set-up time with respect to

the rising edge of pin CLOCK 20 pF total external load

per pin 3.4 3.0 - ns

th(DATA) DATA hold time with respect to

the rising edge of pin CLOCK 20 pF total external load

per pin 0- - ns

td(DATA) DATA output delay with respect

to the rising edge of pin CLOCK 20 pF total external load

per pin 7.7 4.1 - ns

tsu(STP) STP set-up time with respect to

the rising edge of pin CLOCK 20 pF total external load

per pin 3.1 2.7 - ns

th(STP) STP hold time with respect to

the rising edge of pin CLOCK 20 pF total external load

per pin 0- - ns

td(DIR) DIR output delay with respect to

the rising edge of pin CLOCK 20 pF total external load

per pin 7.3 3.8 - ns

td(NXT) NXT output delay with respect to

the rising edge of pin CLOCK 20 pF total external load

per pin 7.3 3.8 - ns

Table 49. Dynamic characteristics: digital I/O pins

…continued

= 3.0 V to 3.6 V; V

CC(I/O)

= 1.65 V to 3.6 V; T

amb

−

C to +85

C; unless otherwise speciﬁed.

Typical values are at V

= 3.3 V; T

amb

= +25

C; unless otherwise speciﬁed.

Symbol Parameter Conditions Min Typ Max Unit

Table 50. Dynamic characteristics: analog I/O pins (DP, DM)

= 3.0 V to 3.6 V; V

CC(I/O)

= 1.65 V to 3.6 V; T

amb

−

C to +85

C; unless otherwise speciﬁed.

Typical values are at V

= 3.3 V; V

CC(I/O)

= 3.3 V; T

amb

= +25

C; unless otherwise speciﬁed.

Symbol Parameter Conditions Min Typ Max Unit

High-speed driver

tHSR rise time (10 % to 90 %) 500 - - ps

tHSF fall time (10 % to 90 %) 500 - - ps

Full-speed driver

tFR rise time CL= 50 pF; 10 % to 90 % of

|VOH −VOL|4 - 20 ns

tFF fall time CL= 50 pF; 10 % to 90 % of

|VOH −VOL|4 - 20 ns

tFRFM differential rise and fall time

matching excluding the ﬁrst transition

from the idle state 90 - 111.1 %

VCRS output signal crossover

voltage excluding the ﬁrst transition

from the idle state 1.3 - 2.0 V

Low-speed driver

tLR transition time: rise time CL= 200 pF to 600 pF;

1.5 kΩ pull-up on DM

enabled; 10 % to 90 % of

|VOH −VOL|

75 - 300 ns

tLF transition time: fall time CL= 200 pF to 600 pF;

1.5 kΩ pull-up on DM

enabled; 10 % to 90 % of

|VOH −VOL|

75 - 300 ns

tLRFM rise and fall time matching tLR/tLF; excluding the ﬁrst

transition from the idle state 80 - 125 %

Product data sheet Rev. 01 — 19 October 2006 63 of 78

NXP Semiconductors ISP1505A; ISP1505C

ULPI HS USB host and peripheral transceiver

Driver timing

tPLH(drv) driver propagation delay

(LOW to HIGH) TX_DAT, TX_SE0 to DP, DM;

see Figure 22 --11ns

tPHL(drv) driver propagation delay

(HIGH to LOW) TX_DAT, TX_SE0 to DP, DM;

see Figure 22 --11ns

tPHZ driver disable delay from

HIGH level TX_ENABLE to DP, DM;

see Figure 23 --12ns

tPLZ driver disable delay from

LOW level TX_ENABLE to DP, DM;

see Figure 23 --12ns

tPZH driver enable delay to HIGH

level TX_ENABLE to DP, DM;

see Figure 23 --20ns

tPZL driver enable delay to LOW

level TX_ENABLE to DP, DM;

see Figure 23 --20ns

Receiver timing

Differential receiver

tPLH(rcv) receiver propagation delay

(LOW to HIGH) DP, DM to RX_RCV, RX_DP

and RX_DM; see Figure 24 --17ns

tPHL(rcv) receiver propagation delay

(HIGH to LOW) DP, DM to RX_RCV, RX_DP

and RX_DM; see Figure 24 --17ns

Single-ended receiver

tPLH(se) single-ended propagation

delay (LOW to HIGH) DP, DM to RX_RCV, RX_DP

and RX_DM; see Figure 24 --17ns

tPHL(se) single-ended propagation

delay (HIGH to LOW) DP, DM to RX_RCV, RX_DP

and RX_DM; see Figure 24 --17ns

Table 50. Dynamic characteristics: analog I/O pins (DP, DM)

…continued

= 3.0 V to 3.6 V; V

CC(I/O)

= 1.65 V to 3.6 V; T

amb

−

C to +85

C; unless otherwise speciﬁed.

Typical values are at V

= 3.3 V; V

CC(I/O)

= 3.3 V; T

amb

= +25

C; unless otherwise speciﬁed.

Symbol Parameter Conditions Min Typ Max Unit

Product data sheet Rev. 01 — 19 October 2006 64 of 78

NXP Semiconductors ISP1505A; ISP1505C

ULPI HS USB host and peripheral transceiver

15.1 ULPI timing

ULPI interface timing requirements are given in Figure 25. This timing applies to

synchronous mode only. All timing is measured with respect to the ISP1505 CLOCK pin.

All signals are clocked on the rising edge of CLOCK.

Fig 21. Rise time and fall time Fig 22. Timing of TX_DAT and TX_SE0 to DP and DM

Fig 23. Timing of TX_ENABLE to DP and DM Fig 24. Timing of DP and DM to RX_RCV, RX_DP and

RX_DM

004aaa861

VOL

tHSR, tFR, tLR tHSF, tFF, tLF

VOH 90 %

10 % 10 %

90 %

004aaa573

VOL

VOH

tPHL(drv)

tPLH(drv)

VCRS VCRS

0.9 V

1.8 V

0 V

logic input

differential

data lines

004aaa574

VOL

VOH

tPZH

tPZL tPHZ

tPLZ

VOH − 0.3 V

VOL + 0.3 V

VCRS

0.9 V

1.8 V

0 V

logic

input

differential

data lines

tPLH(se) tPHL(se)

004aaa575

VOL

VOH

tPHL(rcv)

tPLH(rcv)

VCRS VCRS

0.9 V

2.0 V

0.8 V

logic output

differential

data lines

Fig 25. ULPI timing interface

CLOCK

CONTROL IN

(STP)

DATA IN

(8-BIT)

tsu(STP) th(STP)

tsu(DATA) th(DATA)

CONTROL OUT

(DIR, NXT)

DATA OUT

(8-BIT)

004aaa722

td(DIR),

td(NXT)

td(DATA) td(DIR),

td(NXT)

Product data sheet Rev. 01 — 19 October 2006 65 of 78

NXP Semiconductors ISP1505A; ISP1505C

ULPI HS USB host and peripheral transceiver

16. Application information

[1] For detailed information and alternative interface options, refer to the

Interfacing to the ISP1504/5/6 (AN10048)

application note.

Table 51. Recommended bill of materials

Designator[1] Application Value Comment

Cbypass highly recommended for all

applications 0.1 µF-

Cﬁlter highly recommended for all

applications 4.7 µF±20 %; use a LOW

ESR capacitor (0.2 Ω to

2Ω) for best performance

CVBUS mandatory for peripherals 0.1 µF and1 µFto10µFin

parallel -

mandatory for host 0.1 µF and 120 µF±20 %

(min) in parallel -

mandatory for OTG 0.1 µF and 1 µFto6.5µF

in parallel -

DESD recommended for all

ESD-sensitive applications IP4059CX5/LF Wafer-Level Chip-Scale Package (WLCSP);

1.34 mm ×0.96 mm ×0.41 mm; ESD

IEC 61000-4-2 level 4; ±8 kV contact; ±15 kV

air discharge

Rpullup recommended; for applications

with an external VBUS supply

controlled by PSW_N

4.7 kΩto 100 kΩ (10 kΩ

recommended) maximum value is determined by the voltage

drop on PSW_N caused by leakage into

PSW_N and the external supply control pin

RRREF mandatory in all applications 12 kΩ±1% -

RVBUS strongly recommended for

peripheral or external 5 V

applications only

1kΩ±5% -

RXTAL required only for applications

driving a square wave into the

XTAL1 pin

47 kΩ±5 % used to avoid ﬂoating input on the XTAL1 pin

XTAL crystal is used 19.2 MHz CL= 10 pF; RS< 220 Ω; CXTAL =18pF

26 MHz CL= 10 pF; RS< 130 Ω; CXTAL =18pF

C(XTAL)SQ required only for applications

driving a square wave into the

XTAL1 pin that has a DC offset

100 pF used to AC couple the input square wave to

the XTAL1 pin

xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx

xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x

xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx

xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx

Product data sheet Rev. 01 — 19 October 2006 66 of 78

NXP Semiconductors ISP1505A; ISP1505C

ULPI HS USB host and peripheral transceiver

(1) Frequency is version dependent: ISP1505ABS: 19.2 MHz; ISP1505CBS: 26 MHz.

Fig 26. Using the ISP1505 with a USB Host Controller; external 5 V source with built-in FAULT and external crystal

ISP1505

DATA1

VCC(I/O)

RREF

VCC

DATA2

DATA3

VCC(I/O)

DATA4

CLOCK

DATA5

DATA6

DATA7

NXT

STP

VBUS/FAULT

REG3V3

XTAL1

XTAL2 11

DIR

REG1V8

RESET_N/

PSW_N 12 13

HOST

CONTROLLER

USB STANDARD

OR MINI-A

RECEPTACLE

VBUS

D−

D+

GND

NXT

CLOCK

STP

DIR RESET_N

(optional)

VCC(I/O)

VCC

GND (die pad)

DATA0

004aaa589

XTAL(1)

+5 V

IN FAULT

ON OUT

VBUS

SWITCH

Rpullup Cbypass Cbypass

Cbypass Cfilter Cbypass Cfilter

CVBUS CXTAL CXTAL

RRREF

SHIELD

Cbypass

IP4059CX5/LF

C1 A1 A3 C3

DESD

RVBUS

xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx

xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x

xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx

xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx

Product data sheet Rev. 01 — 19 October 2006 67 of 78

NXP Semiconductors ISP1505A; ISP1505C

ULPI HS USB host and peripheral transceiver

Fig 27. Using the ISP1505 with a Peripheral Controller; external 60 MHz input on CLOCK

ISP1505

DATA0

VCC(I/O)

RREF

DATA2

DATA3

VCC(I/O)

CLOCK

DATA4

DATA5

DATA6

DATA7

NXT

004aaa590

VBUS/FAULT

REG3V3

XTAL1

XTAL2 11

STP

DIR

REG1V8

RESET_N/PSW_N 12 13

PERIPHERAL

CONTROLLER

USB MINI-B OR

STANDARD-B

RECEPTACLE

VBUS

D+

GND

CLOCK

NXT

STP

DIR RESET_N

(optional)

VCC(I/O)

VCC

GND (die pad)

DATA1

VCC

Cbypass Cfilter

Cbypass Cbypass

RRREF

SHIELD

Cbypass

RVBUS

IP4059CX5/LF

C1 A1 A3 C3

DESD

xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx

xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x

xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx

xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx

Product data sheet Rev. 01 — 19 October 2006 68 of 78

NXP Semiconductors ISP1505A; ISP1505C

ULPI HS USB host and peripheral transceiver

(1) Frequency is version dependent: ISP1505ABS: 19.2 MHz; ISP1505CBS: 26 MHz.

Fig 28. Using the ISP1505 with a Peripheral Controller; external square wave input on pin XTAL1

ISP1505

DATA0

VCC(I/O)

RREF

DATA2

DATA3

VCC(I/O)

CLOCK

DATA4

DATA5

DATA6

DATA7

NXT

004aaa896

VBUS/FAULT

REG3V3

XTAL1

XTAL2 11

STP

DIR

REG1V8

RESET_N/

PSW_N 12 13

PERIPHERAL

CONTROLLER

USB MINI-B OR

STANDARD-B

RECEPTACLE

VBUS

D+

GND

CLOCK

NXT

STP

DIR RESET_N

(optional)

VCC(I/O)

VCC

GND (die pad)

DATA1

VCC

Cbypass Cfilter

Cbypass Cbypass

RRREF

SHIELD

Cbypass

RVBUS

IP4059CX5/LF

C1 A1 A3 C3

DESD

RXTAL

C(XTAL)SQ

fi(XTAL1)(1)

Product data sheet Rev. 01 — 19 October 2006 69 of 78

NXP Semiconductors ISP1505A; ISP1505C

ULPI HS USB host and peripheral transceiver

17. Package outline

Fig 29. Package outline SOT616-1 (HVQFN24)

0.51 0.2

A1Eh

UNIT ye

REFERENCES

OUTLINE

VERSION EUROPEAN

PROJECTION ISSUE DATE

IEC JEDEC JEITA

mm 4.1

3.9

2.25

1.95

4.1

3.9 2.25

1.95

2.5

0.30

0.18

0.05

0.00 0.05 0.1

DIMENSIONS (mm are the original dimensions)

SOT616-1 MO-220 - - -- - -

0.5

0.3

0.1

0.05

0 2.5 5 mm

scale

SOT616-1

HVQFN24: plastic thermal enhanced very thin quad flat package; no leads;

24 terminals; body 4 x 4 x 0.85 mm

A(1)

max.

AA1c

detail X

y1C

712

24 19

01-08-08

02-10-22

terminal 1

index area

terminal 1

index area

1/2 e

E(1)

Note

1. Plastic or metal protrusions of 0.075 mm maximum per side are not included.

D(1)

Product data sheet Rev. 01 — 19 October 2006 70 of 78

NXP Semiconductors ISP1505A; ISP1505C

ULPI HS USB host and peripheral transceiver

18. Soldering

This text provides a very brief insight into a complex technology. A more in-depth account

of soldering ICs can be found in Application Note

AN10365 “Surface mount reﬂow

soldering description”

18.1 Introduction to soldering

Soldering is one of the most common methods through which packages are attached to

Printed Circuit Boards (PCBs), to form electrical circuits. The soldered joint provides both

the mechanical and the electrical connection. There is no single soldering method that is

ideal for all IC packages. Wave soldering is often preferred when through-hole and

Surface Mount Devices (SMDs) are mixed on one printed wiring board; however, it is not

suitable for ﬁne pitch SMDs. Reﬂow soldering is ideal for the small pitches and high

densities that come with increased miniaturization.

18.2 Wave and reﬂow soldering

Wave soldering is a joining technology in which the joints are made by solder coming from

a standing wave of liquid solder. The wave soldering process is suitable for the following:

•Through-hole components

•Leaded or leadless SMDs, which are glued to the surface of the printed circuit board

Not all SMDs can be wave soldered. Packages with solder balls, and some leadless

packages which have solder lands underneath the body, cannot be wave soldered. Also,

leaded SMDs with leads having a pitch smaller than ~0.6 mm cannot be wave soldered,

due to an increased probability of bridging.

The reﬂow soldering process involves applying solder paste to a board, followed by

component placement and exposure to a temperature proﬁle. Leaded packages,

packages with solder balls, and leadless packages are all reﬂow solderable.

Key characteristics in both wave and reﬂow soldering are:

•Board speciﬁcations, including the board ﬁnish, solder masks and vias

•Package footprints, including solder thieves and orientation

•The moisture sensitivity level of the packages

•Package placement

•Inspection and repair

•Lead-free soldering versus PbSn soldering

18.3 Wave soldering

Key characteristics in wave soldering are:

•Process issues, such as application of adhesive and ﬂux, clinching of leads, board

transport, the solder wave parameters, and the time during which components are

exposed to the wave

•Solder bath speciﬁcations, including temperature and impurities

Product data sheet Rev. 01 — 19 October 2006 71 of 78

NXP Semiconductors ISP1505A; ISP1505C

ULPI HS USB host and peripheral transceiver

18.4 Reﬂow soldering

Key characteristics in reﬂow soldering are:

•Lead-free versus SnPb soldering; note that a lead-free reﬂow process usually leads to

higher minimum peak temperatures (see Figure 30) than a PbSn process, thus

reducing the process window

•Solder paste printing issues including smearing, release, and adjusting the process

window for a mix of large and small components on one board

•Reﬂow temperature proﬁle; this proﬁle includes preheat, reﬂow (in which the board is

heated to the peak temperature) and cooling down. It is imperative that the peak

temperature is high enough for the solder to make reliable solder joints (a solder paste

characteristic). In addition, the peak temperature must be low enough that the

packages and/or boards are not damaged. The peak temperature of the package

depends on package thickness and volume and is classiﬁed in accordance with

Table 52 and 53

Moisture sensitivity precautions, as indicated on the packing, must be respected at all

times.

Studies have shown that small packages reach higher temperatures during reﬂow

soldering, see Figure 30.

Table 52. SnPb eutectic process (from J-STD-020C)

Package thickness (mm) Package reﬂow temperature (°C)

Volume (mm3)

< 350 ≥ 350

< 2.5 235 220

≥ 2.5 220 220

Table 53. Lead-free process (from J-STD-020C)

Package thickness (mm) Package reﬂow temperature (°C)

Volume (mm3)

< 350 350 to 2000 > 2000

< 1.6 260 260 260

1.6 to 2.5 260 250 245

> 2.5 250 245 245

Product data sheet Rev. 01 — 19 October 2006 72 of 78

NXP Semiconductors ISP1505A; ISP1505C

ULPI HS USB host and peripheral transceiver

For further information on temperature proﬁles, refer to Application Note

AN10365

“Surface mount reﬂow soldering description”

19. Abbreviations

MSL: Moisture Sensitivity Level

Fig 30. Temperature proﬁles for large and small components

001aac844

temperature

time

minimum peak temperature

= minimum soldering temperature

maximum peak temperature

= MSL limit, damage level

peak

temperature

Table 54. Abbreviations

Acronym Description

ASIC Application-Speciﬁc Integrated Circuit

ATX Analog USB Transceiver

CD-RW Compact Disc-Rewritable

EOP End-Of-Packet

ESD ElectroStatic Discharge

FS Full-Speed

HBM Human Body Model

HNP Host Negotiation Protocol

HS High-Speed

ID Identiﬁcation

LS Low-Speed

MO Magneto-Optical

NRZI Non-Return-to-Zero Inverted

OTG On-The-Go

PCB Printed-Circuit Board

PDA Personal Digital Assistant

PHY Physical Layer[1]

PID Packet Identiﬁer

PLD Programmable Logic Device

Product data sheet Rev. 01 — 19 October 2006 73 of 78

NXP Semiconductors ISP1505A; ISP1505C

ULPI HS USB host and peripheral transceiver

[1] Physical layer containing the USB transceiver. The ISP1505 is a PHY.

20. References

[1] Universal Serial Bus Speciﬁcation Rev. 2.0

[2] On-The-Go Supplement to the USB 2.0 Speciﬁcation Rev. 1.2

[3] UTMI+ Low Pin Interface (ULPI) Speciﬁcation Rev. 1.1

[4] UTMI+ Speciﬁcation Rev. 1.0

[5] USB 2.0 Transceiver Macrocell Interface (UTMI) Speciﬁcation Ver. 1.05

[6] Electrostatic Discharge (ESD) Sensitivity Testing Human Body Model (HBM)

(JESD22-A114D)

[7] Interfacing to the ISP1504/5/6 (AN10048)

21. Revision history

PLL Phase-Locked Loop

POR Power-On Reset

RMS Root Mean Square

RoHS Restriction of Hazardous Substances

RXCMD Receive Command

SE0 Single-Ended Zero

SOF Start-Of-Frame

SRP Session Request Protocol

STB Set-Top Box

SYNC Synchronous

TTL Transistor-Transistor Logic

TXCMD Transmit Command

USB Universal Serial Bus

USB-IF USB Implementers Forum

ULPI UTMI+ Low Pin Interface

UTMI USB 2.0 Transceiver Macrocell Interface

UTMI+ USB 2.0 Transceiver Macrocell Interface Plus

Table 54. Abbreviations

…continued

Acronym Description

Table 55. Revision history

Document ID Release date Data sheet status Change notice Supersedes

ISP1505A_ISP1505C_1 20061019 Product data sheet - -

Product data sheet Rev. 01 — 19 October 2006 74 of 78

NXP Semiconductors ISP1505A; ISP1505C

ULPI HS USB host and peripheral transceiver

22. Legal information

22.1 Data sheet status

[1] Please consult the most recently issued document before initiating or completing a design.

[2] The term ‘short data sheet’ is explained in section “Deﬁnitions”.

[3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status

information is available on the Internet at URL http://www.nxp.com.

22.2 Deﬁnitions

Draft — The document is a draft version only. The content is still under

internal review and subject to formal approval, which may result in

modiﬁcations or additions. NXP Semiconductors does not give any

representations or warranties as to the accuracy or completeness of

information included herein and shall have no liability for the consequences of

use of such information.

Short data sheet — A short data sheet is an extract from a full data sheet

with the same product type number(s) and title. A short data sheet is intended

for quick reference only and should not be relied upon to contain detailed and

full information. For detailed and full information see the relevant full data

sheet, which is available on request via the local NXP Semiconductors sales

ofﬁce. In case of any inconsistency or conﬂict with the short data sheet, the

full data sheet shall prevail.

22.3 Disclaimers

General — Information in this document is believed to be accurate and

reliable. However, NXP Semiconductors does not give any representations or

warranties, expressed or implied, as to the accuracy or completeness of such

information and shall have no liability for the consequences of use of such

information.

Right to make changes — NXP Semiconductors reserves the right to make

changes to information published in this document, including without

limitation speciﬁcations and product descriptions, at any time and without

notice. This document supersedes and replaces all information supplied prior

to the publication hereof.

Suitability for use — NXP Semiconductors products are not designed,

authorized or warranted to be suitable for use in medical, military, aircraft,

space or life support equipment, nor in applications where failure or

malfunction of a NXP Semiconductors product can reasonably be expected to

result in personal injury, death or severe property or environmental damage.

NXP Semiconductors accepts no liability for inclusion and/or use of NXP

Semiconductors products in such equipment or applications and therefore

such inclusion and/or use is at the customer’s own risk.

Applications — Applications that are described herein for any of these

products are for illustrative purposes only. NXP Semiconductors makes no

representation or warranty that such applications will be suitable for the

speciﬁed use without further testing or modiﬁcation.

Limiting values — Stress above one or more limiting values (as deﬁned in

the Absolute Maximum Ratings System of IEC 60134) may cause permanent

damage to the device. Limiting values are stress ratings only and operation of

the device at these or any other conditions above those given in the

Characteristics sections of this document is not implied. Exposure to limiting

values for extended periods may affect device reliability.

Terms and conditions of sale — NXP Semiconductors products are sold

subject to the general terms and conditions of commercial sale, as published

at http://www.nxp.com/proﬁle/terms, including those pertaining to warranty,

intellectual property rights infringement and limitation of liability, unless

explicitly otherwise agreed to in writing by NXP Semiconductors. In case of

any inconsistency or conﬂict between information in this document and such

terms and conditions, the latter will prevail.

No offer to sell or license — Nothing in this document may be interpreted

or construed as an offer to sell products that is open for acceptance or the

grant, conveyance or implication of any license under any copyrights, patents

or other industrial or intellectual property rights.

22.4 Trademarks

Notice: All referenced brands, product names, service names and trademarks

are the property of their respective owners.

23. Contact information

For additional information, please visit: http://www.nxp.com

For sales ofﬁce addresses, send an email to: salesaddresses@nxp.com

Document status[1][2] Product status[3] Deﬁnition

Objective [short] data sheet Development This document contains data from the objective speciﬁcation for product development.

Preliminary [short] data sheet Qualiﬁcation This document contains data from the preliminary speciﬁcation.

Product [short] data sheet Production This document contains the product speciﬁcation.

Product data sheet Rev. 01 — 19 October 2006 75 of 78

continued >>

NXP Semiconductors ISP1505A; ISP1505C

ULPI HS USB host and peripheral transceiver

24. Tables

Table 1. Ordering information . . . . . . . . . . . . . . . . . . . . .3

Table 2. Pin description . . . . . . . . . . . . . . . . . . . . . . . . . .5

Table 3. ULPI signal description . . . . . . . . . . . . . . . . . .14

Table 4. Signal mapping during low-power mode . . . . .15

Table 5. Signal mapping for 6-pin serial mode . . . . . . .16

Table 6. Signal mapping for 3-pin serial mode . . . . . . .17

Table 7. Operating states and resistor settings . . . . . . .17

Table 8. TXCMD byte format . . . . . . . . . . . . . . . . . . . . .23

Table 9. RXCMD byte format . . . . . . . . . . . . . . . . . . . . .24

Table 10. LINESTATE[1:0] encoding for upstream

facing ports: peripherals . . . . . . . . . . . . . . . . .25

Table 11. LINESTATE[1:0] encoding for downstream

facing ports: host . . . . . . . . . . . . . . . . . . . . . . .26

Table 12. VBUS indicators in RXCMD for typical

applications . . . . . . . . . . . . . . . . . . . . . . . . . . .27

Table 13. PHY pipeline delays . . . . . . . . . . . . . . . . . . . . .32

Table 14. Link decision times . . . . . . . . . . . . . . . . . . . . .33

Table 15. Register map overview . . . . . . . . . . . . . . . . . .45

Table 16. Vendor ID Low register (address R = 00h)

bit description . . . . . . . . . . . . . . . . . . . . . . . . .45

Table 17. Vendor ID High register (address R = 01h)

bit description . . . . . . . . . . . . . . . . . . . . . . . . .46

Table 18. Product ID Low register (address R = 02h)

bit description . . . . . . . . . . . . . . . . . . . . . . . . .46

Table 19. Product ID High register (address R = 03h)

bit description . . . . . . . . . . . . . . . . . . . . . . . . .46

Table 20. Function Control register

(address R = 04h to 06h, W = 04h, S = 05h,

C = 06h) bit allocation . . . . . . . . . . . . . . . . . . .46

Table 21. Function Control register

(address R = 04h to 06h, W = 04h, S = 05h,

C = 06h) bit description . . . . . . . . . . . . . . . . . .47

Table 22. Interface Control register

(address R = 07h to 09h, W = 07h, S = 08h,

C = 09h) bit allocation . . . . . . . . . . . . . . . . . . .47

Table 23. Interface Control register

(address R = 07h to 09h, W = 07h, S = 08h,

C = 09h) bit description . . . . . . . . . . . . . . . . . .48

Table 24. OTG Control register

(address R = 0Ah to 0Ch, W = 0Ah, S = 0Bh,

C = 0Ch) bit allocation . . . . . . . . . . . . . . . . . . .48

Table 25. OTG Control register

(address R = 0Ah to 0Ch, W = 0Ah, S = 0Bh,

C = 0Ch) bit description . . . . . . . . . . . . . . . . . .49

Table 26. USB Interrupt Enable Rising Edge register

(address R = 0Dh to 0Fh, W = 0Dh, S = 0Eh,

C = 0Fh) bit allocation . . . . . . . . . . . . . . . . . . .49

Table 27. USB Interrupt Enable Rising Edge register

(address R = 0Dh to 0Fh, W = 0Dh, S = 0Eh,

C = 0Fh) bit description . . . . . . . . . . . . . . . . . .50

Table 28. USB Interrupt Enable Falling Edge register

(address R = 10h to 12h, W = 10h, S = 11h,

C = 12h) bit allocation . . . . . . . . . . . . . . . . . . .50

Table 29. USB Interrupt Enable Falling Edge register

(address R = 10h to 12h, W = 10h, S = 11h,

C = 12h) bit description . . . . . . . . . . . . . . . . . .50

Table 30. USB Interrupt Status register

(address R = 13h) bit allocation . . . . . . . . . . .50

Table 31. USB Interrupt Status register

(address R = 13h) bit description . . . . . . . . . .51

Table 32. USB Interrupt Latch register

(address R = 14h) bit allocation . . . . . . . . . . .51

Table 33. USB Interrupt Latch register

(address R = 14h) bit description . . . . . . . . . .51

Table 34. Debug register (address R = 15h)

bit allocation . . . . . . . . . . . . . . . . . . . . . . . . . .51

Table 35. Debug register (address R = 15h)

bit description . . . . . . . . . . . . . . . . . . . . . . . . .52

Table 36. Scratch register (address R = 16h to 18h,

W = 16h, S = 17h, C = 18h) bit description . . .52

Table 37. Power Control register (address R = 3Dh to 3Fh,

W = 3Dh, S = 3Eh, C = 3Fh) bit allocation . . .52

Table 38. Power Control register (address R = 3Dh to 3Fh,

W = 3Dh, S = 3Eh, C = 3Fh) bit description . .53

Table 39. Limiting values . . . . . . . . . . . . . . . . . . . . . . . . .55

Table 40. Recommended operating conditions . . . . . . . .55

Table 41. Static characteristics: supply pins . . . . . . . . . .56

Table 42. Static characteristics: digital pins (CLOCK, DIR,

STP, NXT, DATA[7:0], RESET_N/PSW_N) . . .56

Table 43. Static characteristics: pin VBUS/FAULT . . . . . .57

Table 44. Static characteristics: analog I/O pins

(DP, DM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57

Table 45. Static characteristics: VBUS comparators . . . .59

Table 46. Static characteristics: VBUS resistors . . . . . . . .59

Table 47. Static characteristics: resistor reference . . . . .59

Table 48. Dynamic characteristics: reset and clock . . . .60

Table 49. Dynamic characteristics: digital I/O pins . . . . .61

Table 50. Dynamic characteristics: analog I/O pins

(DP, DM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62

Table 51. Recommended bill of materials . . . . . . . . . . . .65

Table 52. SnPb eutectic process (from J-STD-020C) . . .71

Table 53. Lead-free process (from J-STD-020C) . . . . . .71

Table 54. Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . .72

Table 55. Revision history . . . . . . . . . . . . . . . . . . . . . . . .73

Product data sheet Rev. 01 — 19 October 2006 76 of 78

continued >>

NXP Semiconductors ISP1505A; ISP1505C

ULPI HS USB host and peripheral transceiver

25. Figures

Fig 1. Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Fig 2. Pin conﬁguration HVQFN24; top view . . . . . . . . . .5

Fig 3. Internal power-on reset timing . . . . . . . . . . . . . . .19

Fig 4. Power-up and reset sequence required before

the ULPI bus is ready for use. . . . . . . . . . . . . . . .21

Fig 5. Interface behavior with respect to RESET_N. . . .22

Fig 6. Single and back-to-back RXCMDs from the

ISP1505 to the link. . . . . . . . . . . . . . . . . . . . . . . .25

Fig 7. RXCMD A_VBUS_VLD indicator source. . . . . . .26

Fig 8. Example of register write, register read,

extended register write and extended

Fig 9. USB reset and high-speed detection

handshake (chirp) sequence . . . . . . . . . . . . . . . .31

Fig 10. Example of using the ISP1505 to transmit and

receive USB data. . . . . . . . . . . . . . . . . . . . . . . . .32

Fig 11. High-speed transmit-to-transmit packet timing. . .33

Fig 12. High-speed receive-to-transmit packet timing . . .34

Fig 13. Preamble sequence. . . . . . . . . . . . . . . . . . . . . . .35

Fig 14. Full-speed suspend and resume . . . . . . . . . . . . .36

Fig 15. High-speed suspend and resume . . . . . . . . . . . .38

Fig 16. Remote wake-up from low-power mode . . . . . . .40

Fig 17. Transmitting USB packets without

the automatic SYNC and EOP generation. . . . . .41

Fig 18. Example of transmit followed by receive

in 6-bit serial mode . . . . . . . . . . . . . . . . . . . . . . .43

Fig 19. Example of transmit followed by receive

in 3-bit serial mode . . . . . . . . . . . . . . . . . . . . . . .43

Fig 20. Human body ESD test model. . . . . . . . . . . . . . . .54

Fig 21. Rise time and fall time . . . . . . . . . . . . . . . . . . . . .64

Fig 22. Timing of TX_DAT and TX_SE0 to DP and DM. .64

Fig 23. Timing of TX_ENABLE to DP and DM. . . . . . . . .64

Fig 24. Timing of DP and DM to RX_RCV, RX_DP

and RX_DM . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64

Fig 25. ULPI timing interface . . . . . . . . . . . . . . . . . . . . . .64

Fig 26. Using the ISP1505 with a USB Host Controller;

external 5 V source with built-in FAULT

and external crystal . . . . . . . . . . . . . . . . . . . . . . .66

Fig 27. Using the ISP1505 with a Peripheral Controller;

external 60 MHz input on CLOCK . . . . . . . . . . . .67

Fig 28. Using the ISP1505 with a Peripheral Controller;

external square wave input on pin XTAL1 . . . . . .68

Fig 29. Package outline SOT616-1 (HVQFN24) . . . . . . .69

Fig 30. Temperature proﬁles for large and small

components . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72

Product data sheet Rev. 01 — 19 October 2006 77 of 78

continued >>

NXP Semiconductors ISP1505A; ISP1505C

ULPI HS USB host and peripheral transceiver

26. Contents

1 General description. . . . . . . . . . . . . . . . . . . . . . 1

2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

3 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

4 Ordering information. . . . . . . . . . . . . . . . . . . . . 3

5 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 4

6 Pinning information. . . . . . . . . . . . . . . . . . . . . . 5

6.1 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

6.2 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 5

7 Functional description . . . . . . . . . . . . . . . . . . . 7

7.1 ULPI interface controller . . . . . . . . . . . . . . . . . . 7

7.2 USB serializer and deserializer. . . . . . . . . . . . . 7

7.3 Hi-Speed USB (USB 2.0) ATX . . . . . . . . . . . . . 7

7.4 Voltage regulator. . . . . . . . . . . . . . . . . . . . . . . . 8

7.5 Crystal oscillator and PLL. . . . . . . . . . . . . . . . . 8

7.6 VBUS comparators. . . . . . . . . . . . . . . . . . . . . . . 8

7.6.1 VBUS valid comparator . . . . . . . . . . . . . . . . . . . 8

7.6.2 Session valid comparator . . . . . . . . . . . . . . . . . 9

7.6.3 Session end comparator. . . . . . . . . . . . . . . . . . 9

7.7 SRP charge and discharge resistors . . . . . . . . 9

7.8 Band gap reference voltage . . . . . . . . . . . . . . . 9

7.9 Power-on reset . . . . . . . . . . . . . . . . . . . . . . . . . 9

7.10 Detailed description of pins . . . . . . . . . . . . . . . 9

7.10.1 DATA[7:0] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

7.10.2 VCC(I/O) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

7.10.3 RREF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

7.10.4 DP and DM. . . . . . . . . . . . . . . . . . . . . . . . . . . 10

7.10.5 VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

7.10.6 VBUS/FAULT . . . . . . . . . . . . . . . . . . . . . . . . . . 10

7.10.6.1 VBUS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

7.10.6.2 FAULT (external overcurrent or fault detector) 10

7.10.7 REG3V3 and REG1V8 . . . . . . . . . . . . . . . . . . 11

7.10.8 XTAL1 and XTAL2. . . . . . . . . . . . . . . . . . . . . . 11

7.10.9 RESET_N/PSW_N . . . . . . . . . . . . . . . . . . . . . 11

7.10.9.1 RESET_N. . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

7.10.9.2 PSW_N. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

7.10.10 DIR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

7.10.11 STP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

7.10.12 NXT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

7.10.13 CLOCK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

7.10.14 GND (die pad). . . . . . . . . . . . . . . . . . . . . . . . . 13

8 Modes of operation . . . . . . . . . . . . . . . . . . . . . 14

8.1 ULPI modes . . . . . . . . . . . . . . . . . . . . . . . . . . 14

8.1.1 Synchronous mode. . . . . . . . . . . . . . . . . . . . . 14

8.1.2 Low-power mode . . . . . . . . . . . . . . . . . . . . . . 15

8.1.3 6-pin full-speed or low-speed serial mode . . . 16

8.1.4 3-pin full-speed or low-speed serial mode . . . 16

8.2 USB and OTG state transitions . . . . . . . . . . . 17

9 Protocol description . . . . . . . . . . . . . . . . . . . . 19

9.1 ULPI references . . . . . . . . . . . . . . . . . . . . . . . 19

9.2 Power-On Reset (POR) . . . . . . . . . . . . . . . . . 19

9.3 Power-up, reset and bus idle sequence . . . . . 19

9.3.1 Interface protection. . . . . . . . . . . . . . . . . . . . . 22

9.3.2 Interface behavior with respect to RESET_N. 22

9.4 VBUS power and fault detection . . . . . . . . . . . 22

9.4.1 Driving 5 V on VBUS . . . . . . . . . . . . . . . . . . . . 22

9.4.2 Fault detection . . . . . . . . . . . . . . . . . . . . . . . . 23

9.5 TXCMD and RXCMD. . . . . . . . . . . . . . . . . . . 23

9.5.1 TXCMD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

9.5.2 RXCMD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

9.5.2.1 Linestate encoding. . . . . . . . . . . . . . . . . . . . . 25

9.5.2.2 VBUS state encoding. . . . . . . . . . . . . . . . . . . . 26

9.5.2.3 RxEvent encoding . . . . . . . . . . . . . . . . . . . . . 27

9.6 Register read and write operations . . . . . . . . 28

9.7 USB reset and high-speed detection

handshake (chirp) . . . . . . . . . . . . . . . . . . . . . 29

9.8 USB packet transmit and receive. . . . . . . . . . 32

9.8.1 USB packet timing . . . . . . . . . . . . . . . . . . . . . 32

9.8.1.1 ISP1505 pipeline delays. . . . . . . . . . . . . . . . . 32

9.8.1.2 Allowed link decision time . . . . . . . . . . . . . . . 32

9.9 Preamble . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

9.10 USB suspend and resume. . . . . . . . . . . . . . . 35

9.10.1 Full-speed and low-speed host-initiated

suspend and resume . . . . . . . . . . . . . . . . . . . 35

9.10.2 High-speed suspend and resume . . . . . . . . . 36

9.10.3 Remote wake-up . . . . . . . . . . . . . . . . . . . . . . 39

9.11 No automatic SYNC and EOP generation

(optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

9.12 On-The-Go operations. . . . . . . . . . . . . . . . . . 41

9.12.1 OTG comparators. . . . . . . . . . . . . . . . . . . . . . 42

9.12.2 Pull-up and pull-down resistors . . . . . . . . . . . 42

9.12.3 VBUS charge and discharge resistors. . . . . . . 42

9.13 Serial modes . . . . . . . . . . . . . . . . . . . . . . . . . 42

9.14 Aborting transfers. . . . . . . . . . . . . . . . . . . . . . 44

9.15 Avoiding contention on the ULPI data bus . . . 44

10 Register map . . . . . . . . . . . . . . . . . . . . . . . . . . 45

10.1 Immediate register set . . . . . . . . . . . . . . . . . . 45

10.1.1 Vendor ID and Product ID registers . . . . . . . . 45

10.1.1.1 Vendor ID Low register. . . . . . . . . . . . . . . . . . 45

10.1.1.2 Vendor ID High register . . . . . . . . . . . . . . . . . 46

10.1.1.3 Product ID Low register . . . . . . . . . . . . . . . . . 46

10.1.1.4 Product ID High register. . . . . . . . . . . . . . . . . 46

10.1.2 Function Control register . . . . . . . . . . . . . . . . 46

10.1.3 Interface Control register . . . . . . . . . . . . . . . . 47

NXP Semiconductors ISP1505A; ISP1505C

ULPI HS USB host and peripheral transceiver

For more information, please visit: http://www.nxp.com

For sales office addresses, please send an email to: salesaddresses@nxp.com

Date of release: 19 October 2006

Document identifier: ISP1505A_ISP1505C_1

Please be aware that important notices concerning this document and the product(s)

described herein, have been included in section ‘Legal information’.

10.1.4 OTG Control register . . . . . . . . . . . . . . . . . . . 48

10.1.5 USB Interrupt Enable Rising Edge register . . 49

10.1.6 USB Interrupt Enable Falling Edge register . . 50

10.1.7 USB Interrupt Status register . . . . . . . . . . . . . 50

10.1.8 USB Interrupt Latch register. . . . . . . . . . . . . . 51

10.1.9 Debug register . . . . . . . . . . . . . . . . . . . . . . . . 51

10.1.10 Scratch register. . . . . . . . . . . . . . . . . . . . . . . . 52

10.1.11 Reserved . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

10.1.12 Access extended register set . . . . . . . . . . . . . 52

10.1.13 Vendor-speciﬁc registers . . . . . . . . . . . . . . . . 52

10.1.14 Power Control register . . . . . . . . . . . . . . . . . . 52

10.2 Extended register set . . . . . . . . . . . . . . . . . . . 53

11 ElectroStatic Discharge (ESD) . . . . . . . . . . . . 54

11.1 ESD protection . . . . . . . . . . . . . . . . . . . . . . . . 54

11.2 ESD test conditions . . . . . . . . . . . . . . . . . . . . 54

12 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . 55

13 Recommended operating conditions. . . . . . . 55

14 Static characteristics. . . . . . . . . . . . . . . . . . . . 56

15 Dynamic characteristics . . . . . . . . . . . . . . . . . 60

15.1 ULPI timing. . . . . . . . . . . . . . . . . . . . . . . . . . . 64

16 Application information. . . . . . . . . . . . . . . . . . 65

17 Package outline . . . . . . . . . . . . . . . . . . . . . . . . 69

18 Soldering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

18.1 Introduction to soldering . . . . . . . . . . . . . . . . . 70

18.2 Wave and reﬂow soldering . . . . . . . . . . . . . . . 70

18.3 Wave soldering. . . . . . . . . . . . . . . . . . . . . . . . 70

18.4 Reﬂow soldering. . . . . . . . . . . . . . . . . . . . . . . 71

19 Abbreviations. . . . . . . . . . . . . . . . . . . . . . . . . . 72

20 References . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

21 Revision history. . . . . . . . . . . . . . . . . . . . . . . . 73

22 Legal information. . . . . . . . . . . . . . . . . . . . . . . 74

22.1 Data sheet status . . . . . . . . . . . . . . . . . . . . . . 74

22.2 Deﬁnitions. . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

22.3 Disclaimers. . . . . . . . . . . . . . . . . . . . . . . . . . . 74

22.4 Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . 74

23 Contact information. . . . . . . . . . . . . . . . . . . . . 74

24 Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

25 Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

26 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77