FWDM-1519-7D-55 - Finisar Corporation

F i n i s a r

 Finisar June 2003 Rev.C Page 1

Product Specification

CWDM Pluggable SFP Transceiver

FWDM-1519-7D-xx

PRODUCT FEATURES

• Up to 1.25 Gb/s bi-directional

data links

• Hot-pluggable SFP footprint

• Built-in digital diagnostic functions

• Uncooled DFB laser transmitter in

8 possible CWDM wavelengths

• Duplex LC connector

• Very low jitter

• Metal enclosure, for lower EMI

• Single 3.3V power supply

• Low power dissipation <700mW

• Operating temperature range: 0°C

to 70°C

APPLICATIONS

• Metro Access Rings and Point-to-Point

networking for Gigabit Ethernet and

Fibre Channel

Finisar’s FWDM-1519-7D-xx CWDM Small Form Factor Pluggable (SFP) transceivers

are designed for operation in Metro Access Rings and Point-to-Point networks using

Gigabit Ethernet and Fibre Channel networking equipment. They are available in eight

different CWDM wavelengths. Digital diagnostics functions are available via a two wire

serial bus. In addition, they comply with the Small Form Factor Pluggable Multi-

Sourcing Agreement (MSA)1.

PRODUCT SELECTION

FWDM-1519-7D-xx

xx : (See next page)

FWDM-1519-7D-xx SFP Product Specification – June 2003 F i n i s a r

 Finisar June 2003 Rev.C Page 2

Wavelength

xx Clasp Color

Code Wavelength xx Clasp Color

Code

1470 nm 47 Gray 1550 nm 55 Yellow

1490 nm 49 Violet 1570 nm 57 Orange

1510 nm 51 Blue 1590 nm 59 Red

1530 nm 53 Green 1610 nm 61 Brown

I. Pin Descriptions

Pin Symbol Name/Description Ref.

1 VEET Transmitter Ground (Common with Receiver Ground) 1

2 TFAULT Transmitter Fault. Not supported.

3 TDIS Transmitter Disable. Laser output disabled on high or open. 2

4 MOD_DEF(2) Module Definition 2. Data line for Serial ID. 3

5 MOD_DEF(1) Module Definition 1. Clock line for Serial ID. 3

6 MOD_DEF(0) Module Definition 0. Grounded within the module. 3

7 Rate Select No connection required 4

8 LOS Loss of Signal indication. Logic 0 indicates normal operation. 5

9 VEER Receiver Ground (Common with Transmitter Ground) 1

10 VEER Receiver Ground (Common with Transmitter Ground) 1

11 VEER Receiver Ground (Common with Transmitter Ground) 1

12 RD- Receiver Inverted DATA out. AC Coupled

13 RD+ Receiver Non-inverted DATA out. AC Coupled

14 VEER Receiver Ground (Common with Transmitter Ground) 1

15 VCCR Receiver Power Supply

16 VCCT Transmitter Power Supply

17 VEET Transmitter Ground (Common with Receiver Ground) 1

18 TD+ Transmitter Non-Inverted DATA in. 100 ohm termination between TD+

and TD-, AC Coupled thereafter.

19 TD- Transmitter Inverted DATA in. See TD+

20 VEET Transmitter Ground (Common with Receiver Ground) 1

Notes:

1. Circuit ground is internally isolated from chassis ground.

2. Laser output disabled on TDIS >2.0V or open, enabled on TDIS <0.8V.

3. Should be pulled up with 4.7k – 10kohms on host board to a voltage between 2.0V and 5.5V.

MOD_DEF(0) pulls line low to indicate module is plugged in.

4. Finisar 2x receiver achieves simultaneous 1x and 2x operation without active control.

5. LOS is open collector output. Should be pulled up with 4.7k – 10kohms on host board to a voltage

between 2.0V and 5.5V. Logic 0 indicates normal operation; logic 1 indicates loss of signal.

FWDM-1519-7D-xx SFP Product Specification – June 2003 F i n i s a r

 Finisar June 2003 Rev.C Page 3

VeeT

VeeR

TD-

TD+

RD+

RD-

VccT

VccR

VeeT

VeeR

TXFault

MOD-DEF(2)

MOD-DEF(1)

MOD-DEF(0)

Rate Select

LOS

Towards

ASIC

Towards

Bezel

TX Disable

VeeR

Diagram of Host Board Connector Block Pin Numbers and Names

II. Absolute Maximum Ratings

Parameter Symbol Min Typ Max Unit Ref.

Maximum Supply Voltage Vcc -0.5 4.7 V

Storage Temperature TS -40 85 °C

Case Operating Temperature TOP 0 70 °C

Lead Soldering Temperature/Time 260/10 °C/s

III. Electrical Characteristics (TOP = 0 to 70 °C, VCC = 3.15 to 3.60 Volts)

Parameter Symbol Min Typ Max Unit Ref.

Supply Voltage Vcc 3.15 3.60 V

Supply Current Icc 200 300 mA

Transmitter

Input differential impedance Rin 100 Ω 1

Single ended data input swing Vin,pp 250 1200 mV

Transmit Disable Voltage VD Vcc – 1.3

Vcc V

Transmit Enable Voltage VEN Vee Vee+ 0.8 V 2

Transmit Disable Assert Time 10 us

Receiver

Single ended data output swing Vout,pp 250 800 mV 3

Data output rise time tr 100 175 ps 4

Data output fall time tf 100 175 ps 4

LOS Fault VLOS fault Vcc – 0.5

VccHOST V 5

LOS Normal VLOS norm Vee Vee+0.5 V 5

Power Supply Rejection PSR 100 mVpp 6

Notes:

1. Connected directly to TX data input pins. AC coupled thereafter.

FWDM-1519-7D-xx SFP Product Specification – June 2003 F i n i s a r

 Finisar June 2003 Rev.C Page 4

2. Or open circuit.

3. Into 100 ohms differential termination.

4. 20 – 80 %

5. Loss Of Signal is LVTTL. Logic 0 indicates normal operation; logic 1 indicates no signal detected.

6. Receiver sensitivity is compliant with power supply sinusoidal modulation of 20 Hz to 1.5 MHz up to

specified value applied through the recommended power supply filtering network.

IV. Optical Characteristics (TOP = 0 to 70 °C, VCC = 3.15 to 3.60 Volts)

Parameter Symbol Min Typ Max Unit Ref.

Transmitter

Output Opt. Pwr (End of Life) POUT +0 +5 dBm 1

Optical Wavelength λ (x-4) (x+1) (x+7) nm 2

Wavelength Temperature Dependance 0.08 0.125 nm/°C

Spectral Width (-20dB) σ 1 nm

Optical Extinction Ratio ER 9 dB

Sidemode Supression ratio SSRmin 30 dB

Optical Rise/Fall Time tr/ tf 180 ps 3

RIN RIN -120 dB/Hz

Transmitter Jitter (peak to peak) 100 ps

Receiver

Average Rx Sensitivity @ Gigabit

Ethernet RSENS3 -23.0 dBm 4

Maximum Input Power PMAX 0 dBm

Optical Center Wavelength λC 1270 1620 nm

LOS De-Assert LOSD -19 dBm

LOS Assert LOSA -30 dBm

LOS Hysteresis 1.0 dB

Receiver Jitter Generation @1.25Gbps

160 ps 5

Notes:

1. Class 1 Laser Safety per FDA/CDRH and IEC-825-1 regulations.

2. Over case temperature of 0 to 70 °C. The Transmitter Center Wavelength “x” is as specified by the

customer. The current available wavelengths are: 1470, 1490, 1510, 1530, 1550, 1570, 1590, and 1610

nm. Please see the “Product Selection” section on page 1.

3. Unfiltered

4. With worst-case extinction ratio. Measured with a PRBS 27-1 test pattern, @1.25Gb/s, BER<10-12.

5. Jitter added by receiver (peak to peak). Measured at –23dBm average Rx sensitivity, PRBS 27-1 test

pattern.

FWDM-1519-7D-xx SFP Product Specification – June 2003 F i n i s a r

 Finisar June 2003 Rev.C Page 5

V. General Specifications

Parameter Symbol Min Typ Max Units

Ref.

Data Rate BR 0.622 1.25 Gb/sec

Total System Budget -- 23.0 25.0 dB @1.25 Gb/s, BER < 10-12

w/ PRBS 27-1.

VI. Environmental Specifications

Finisar CWDM SFP transceivers have an operating temperature range from

0°C to +70°C case temperature.

Parameter Symbol Min Typ Max Units Ref.

Case Operating Temperature Top 0 70 °C

Storage Temperature Tsto -40 85 °C

VII. Regulatory Compliance

Finisar CWDM SFP transceivers are Class 1 Laser Products. They are certified per the

following standards:

Feature Agency Standard Certificate

Number

Laser Eye Safety

FDA/CDRH CDRH and IEC-825

Class 1 Laser Product.

See Note 1

Laser Eye Safety

TÜV EN 60950

EN 60825-1

EN 60825-2

Electrical Safety

CSA

CLASS 3862.07

CLASS 3862.87

Note 1: Complies with FDA performance standards for laser products except for deviations pursuant to

Laser Notice No. 50, dated July 26, 2001.

FWDM-1519-7D-xx SFP Product Specification – June 2003 F i n i s a r

 Finisar June 2003 Rev.C Page 6

VIII. Digital Diagnostic Functions

Finisar FWDM-1519-7D-xx SFP transceivers support the 2-wire serial communication

protocol as defined in the draft SFP MSA1. It is very closely related to the E2PROM

defined in the GBIC standard, with the same electrical specifications.

The standard SFP serial ID provides access to identification information that describes

the transceiver’s capabilities, standard interfaces, manufacturer, and other information.

Additionally, Finisar SFP transceivers provide a unique enhanced digital diagnostic

monitoring interface, which allows real-time access to device operating parameters such

as transceiver temperature, laser bias current, transmitted optical power, received optical

power and transceiver supply voltage. It also defines a sophisticated system of alarm and

warning flags, which alerts end-users when particular operating parameters are outside of

a factory set normal range.

The SFP MSA defines a 256-byte memory map in E2PROM that is accessible over a

2-wire serial interface at the 8 bit address 1010000X (A0h). The digital diagnostic

monitoring interface makes use of the 8 bit address 1010001X (A2h), so the originally

defined serial ID memory map remains unchanged. The interface is identical to, and is

thus fully backward compatible with both the GBIC Specification and the SFP Multi

Source Agreement. The complete interface is described in Finisar Application Note AN-

2030: “Digital Diagnostics Monitoring Interface for SFP Optical Transceivers”.

FWDM-1519-7D-xx SFP Product Specification – June 2003 F i n i s a r

 Finisar June 2003 Rev.C Page 7

IX. Mechanical Specifications

Finisar’s Multi-rate CWDM Small Form Factor Pluggable (SFP) transceivers are

compatible with the dimensions defined by the SFP Multi-Sourcing Agreement (MSA).

FWDM-1519-7D-xx (dimensions are in inches)

FWDM-1519-7D-xx SFP Product Specification – June 2003 F i n i s a r

 Finisar June 2003 Rev.C Page 8

X. PCB Layout and Bezel Recommendations

FWDM-1519-7D-xx SFP Product Specification – June 2003 F i n i s a r

 Finisar June 2003 Rev.C Page 9

FWDM-1519-7D-xx SFP Product Specification – June 2003 F i n i s a r

 Finisar June 2003 Rev.C Page 10

XI. References

1. Small Form Factor Pluggable (SFP) Transceiver Multi-Source Agreement (MSA),

September 2000. Documentation is currently available at Finisar upon request.

2. Bellcore GR-253 and ITU-T G.957 Specifications.

3. IEEE Std 802.3. IEEE Standards Department, 2000.(*)

4. “Fibre Channel Draft Physical Interface Specification (FC-PI 10.0)”. American

National Standard for Information Systems.(*)

(*) Neither IEEE 802.3 nor FC-PI 10.0 specifies a 15xx nm DFB single mode interface.

The FWDM-1519-7D-xx complies with these specifications except for the following

optical parameters, which have different values: transmitter wavelength, receiver

sensitivity, and transmit output power. See Section IV for details.

XII. For More Information

Finisar Corporation

1308 Moffett Park Drive

Sunnyvale, CA 94089-1133

Tel. 1-408-548-1000

Fax 1-408-541-6138

sales@finisar.com