19-1446; Rev 2; 5/06 +5V/+3V, 12-Bit, Serial, Force/Sense DACs with 10ppm/C Internal Reference The MAX5122/MAX5123 low-power, 12-bit, voltage-output, digital-to-analog converters (DACs) feature an internal precision bandgap reference and output amplifier. The MAX5122 operates on a single +5V supply with an internal +2.5V reference, and offers a configurable output amplifier. If necessary, the user can override the on-chip, <10ppm/C voltage reference with an external reference. The MAX5123 has the same features as the MAX5122 but operates from a single +3V supply and has an internal +1.25V precision reference. The user-accessible inverting input and output of the amplifier allows specific gain configurations, remote sensing, and high output drive capability for a wide range of force/sense applications. Both devices draw only 500A of supply current, which reduces to 3A in power-down mode. In addition, their power-up reset feature allows for a user-selectable initial output state of either 0V or midscale and reduces output glitches during power-up. The serial interface is compatible with SPITM, QSPITM, and MICROWIRETM, which makes the MAX5122/MAX5123 suitable for cascading multiple devices. Each DAC has a double-buffered input organized as an input register followed by a DAC register. A 16-bit shift register loads data into the input register. The DAC register may be updated independently or simultaneously with the input register. Both devices are available in a 16-pin QSOP package and are specified for the extended-industrial (-40C to +85C) operating temperature range. For pin-compatible 14-bit upgrades, see the MAX5171/MAX5173 data sheet; for the pin-compatible 13-bit version, see the MAX5132/ MAX5133 data sheet. Applications Features Single-Supply Operation +5V (MAX5122) +3V (MAX5123) Built-In 10ppm/C max Precision Bandgap Reference +2.5V (MAX5122) +1.25V (MAX5123) SPI/QSPI/MICROWIRE-Compatible, 3-Wire Serial Interface Pin-Programmable Shutdown Mode and PowerUp Reset (0 or Midscale Output Voltage) Buffered Output Capable of Driving 5k 100pF or 4-20mA Loads Space-Saving 16-Pin QSOP Package Pin-Compatible 13-Bit Upgrades Available (MAX5132/MAX5133) Pin-Compatible 14-Bit Upgrades Available (MAX5171/MAX5173) Ordering Information PART PINPACKAGE INL (LSB) PKG CODE MAX5122AEEE 16 QSOP 0.5 E16-5 MAX5122BEEE 16 QSOP 1 E16-5 MAX5123AEEE 16 QSOP 1 E16-5 MAX5123BEEE 16 QSOP 2 E16-5 Note: All devices are specified over the -40C to +85C operating temperature range. Pin Configuration Industrial Process Control Automatic Test Equipment Digital Offset and Gain Adjustment TOP VIEW FB 1 16 VDD OUT 2 Motion Control 15 REFADJ RSTVAL 3 Microprocessor-Controlled Systems PDL 4 CLR 5 14 REF MAX5122 MAX5123 12 PD CS 6 11 UPO DIN 7 10 DOUT 9 SCLK 8 SPI and QSPI are trademarks of Motorola, Inc. MICROWIRE is a trademark of National Semiconductor Corp. 13 AGND DGND QSOP ________________________________________________________________ Maxim Integrated Products For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at 1-888-629-4642, or visit Maxim's website at www.maxim-ic.com. 1 MAX5122/MAX5123 General Description MAX5122/MAX5123 +5V/+3V, 12-Bit, Serial, Force/Sense DACs with 10ppm/C Internal Reference ABSOLUTE MAXIMUM RATINGS VDD to AGND, DGND ...............................................-0.3V to +6V AGND to DGND.....................................................-0.3V to +0.3V Digital Inputs to DGND.............................................-0.3V to +6V Digital Outputs (DOUT, UPO) to DGND .....-0.3V to (VDD + 0.3V) FB, OUT to AGND ......................................-0.3V to (VDD + 0.3V) REF, REFADJ to AGND ..............................-0.3V to (VDD + 0.3V) Maximum Current into Any Pin............................................50mA Continuous Power Dissipation (TA = +70C) QSOP (derate 8.00mW/C above +70C) .....................667mW Operating Temperature Range ...........................-40C to +85C Storage Temperature Range .............................-65C to +150C Lead Temperature (soldering, 10s) .................................+300C Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICS--MAX5122 (+5V) (VDD = +5V 10%, AGND = DGND, 33nF capacitor at REFADJ, internal reference, RL = 5k, CL = 100pF, output amplifier configured in unity-gain, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25C.) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS STATIC PERFORMANCE Resolution N 12 Bits MAX5122A -0.5 0.5 MAX5123B -1 1 Integral Nonlinearity (Note 1) INL Differential Nonlinearity DNL -1 1 LSB Offset Error (Note 2) VOS -10 10 mV Gain Error GE -3 3 mV -0.2 LSB MAX5122A 3 10 MAX5123B 10 30 PSRR 4.5V VDD 5.5V 20 250 V/V VREF TA = +25C 2.5 2.525 V Full-Scale Temperature Coefficient (Note 3) TCVFS Power-Supply Rejection Ratio ppm/C REFERENCE Output Voltage Output Voltage Temperature Coefficient Reference External Load Regulation TCVREF VOUT/IOUT 2.475 MAX5122A 3 MAX5122B 10 0 IOUT 100A (sourcing) 0.1 REFADJ = VDD 3.3 Reference Short-Circuit Current ppm/C 1 4 REFADJ Current V/A mA 7 A DIGITAL INPUT Input High Voltage VIH Input Low Voltage VIL Input Hysteresis 3 VHYS Input Leakage Current IIN Input Capacitance CIN V 0.8 200 VIN = 0 or VDD -1 0.001 V mV 1 8 A pF DIGITAL OUTPUTS Output High Voltage VOH ISOURCE = 2mA Output Low Voltage VOL ISINK = 2mA 2 VDD - 0.5 V 0.13 _______________________________________________________________________________________ 0.4 V +5V/+3V, 12-Bit, Serial, Force/Sense DACs with 10ppm/C Internal Reference (VDD = +5V 10%, AGND = DGND, 33nF capacitor at REFADJ, internal reference, RL = 5k, CL = 100pF, output amplifier configured in unity-gain, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25C.) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS DYNAMIC PERFORMANCE Voltage Output Slew Rate SR Output Settling Time To 0.5LSB, VSTEP = 2.5V Output Voltage Swing (Note 4) 0.6 V/s 20 s 0 to VDD Current into FB -0.1 Time Required to Exit Shutdown CS = VDD, fSCLK = 100kHz, VSCLK = 5Vp-p Digital Feedthrough 0 V 0.1 A 2 ms 5 nV-sec POWER REQUIREMENTS Power-Supply Voltage (Note 5) Power-Supply Current (Note 5) Power-Supply Current in Shutdown VDD 4.5 5.5 V IDD 500 600 A ISHDN 3 20 A ELECTRICAL CHARACTERISTICS--MAX5123 (+3V) (VDD = +3V 10%, AGND = DGND, 33nF capacitor at REFADJ, internal reference, RL = 5k, CL = 100pF, output amplifier connected in unity-gain, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25C.) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS STATIC PERFORMANCE Resolution N 12 Bits MAX5123A -1 1 MAX5123B -2 2 Integral Nonlinearity (Note 1) INL Differential Nonlinearity DNL -1 1 LSB Offset Error (Note 2) VOS -10 10 mV Gain Error GE -5 5 mV -0.2 LSB MAX5123A 3 10 MAX5123B 10 30 PSRR 2.7V VDD 3.3V 20 250 V/V VREF TA = +25C 1.25 1.263 V Full-Scale Temperature Coefficient (Note 3) TCVFS Power-Supply Rejection Ratio ppm/C REFERENCE Output Voltage Output Voltage Temperature Coefficient Reference External Load Regulation TCVREF VOUT/IOUT 1.237 MAX5123A 3 MAX5123B 10 0 IOUT 100A (sourcing) 0.1 REFADJ = VDD 3.3 Reference Short-Circuit Current ppm/C 1 4 REFADJ Current V/A mA 7 A DIGITAL INPUT Input High Voltage VIH Input Low Voltage VIL Input Hysteresis VHYS 2.2 V 0.8 200 V mV _______________________________________________________________________________________ 3 MAX5122/MAX5123 ELECTRICAL CHARACTERISTICS--MAX5122 (+5V) (continued) MAX5122/MAX5123 +5V/+3V, 12-Bit, Serial, Force/Sense DACs with 10ppm/C Internal Reference ELECTRICAL CHARACTERISTICS--MAX5123 (+3V) (continued) (VDD = +3V 10%, AGND = DGND, 33nF capacitor at REFADJ, internal reference, RL = 5k, CL = 100pF, output amplifier connected in unity-gain, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25C.) PARAMETER SYMBOL Input Leakage Current IIN Input Capacitance CIN CONDITIONS VIN = 0 or VDD MIN TYP MAX UNITS -1 0.001 1 A 8 pF DIGITAL OUTPUTS Output High Voltage VOH ISOURCE = 2mA Output Low Voltage VOL ISINK = 2mA VDD - 0.5 V 0.13 0.4 V DYNAMIC PERFORMANCE Voltage Output Slew Rate SR Output Settling Time To 0.5LSB, VSTEP = 1.25V Output Voltage Swing (Note 4) Current into FB -0.1 Time Required to Exit Shutdown CS = VDD, fSCLK = 100kHz, VSCLK = 3Vp-p Digital Feedthrough 0.6 V/s 20 s 0 to VDD V 0 0.1 A 2 ms 5 nV-sec POWER REQUIREMENTS Power-Supply Voltage (Note 5) Power-Supply Current (Note 5) Power-Supply Current in Shutdown VDD 2.7 3.6 V IDD 500 600 A ISHDN 3 20 A TIMING CHARACTERISTICS--MAX5122 (+5V) (VDD = +5V 10%, AGND = DGND, 33nF capacitor at REFADJ, internal reference, RL = 5k, CL = 100pF, output amplifier connected in unity-gain, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25C.) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS SCLK Clock Period tCP 100 ns SCLK Pulse Width High tCH 40 ns SCLK Pulse Width Low tCL 40 ns CS Fall to SCLK Rise Setup Time tCSS 40 ns SCLK Rise to CS Rise Hold Time tCSH 0 ns SDI Setup Time tDS 40 ns SDI Hold Time tDH 0 ns SCLK Rise to DOUT Valid Propagation Delay Time tDO1 CLOAD = 200pF 80 ns SCLK Fall to DOUT Valid Propagation Delay Time tDO2 CLOAD = 200pF 80 ns SCLK Rise to CS Fall Delay Time tCS0 10 ns CS Rise to SCLK Rise Hold Time tCS1 40 ns CS Pulse Width High tCSW 100 ns 4 _______________________________________________________________________________________ +5V/+3V, 12-Bit, Serial, Force/Sense DACs with 10ppm/C Internal Reference (VDD = +3V 10%, AGND = DGND, 33nF capacitor at REFADJ, internal reference, RL = 5k, CL = 100pF, output amplifier connected in unity-gain, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25C.) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS SCLK Clock Period tCP 150 ns SCLK Pulse Width High tCH 75 ns SCLK Pulse Width Low tCL 75 ns CS Fall to SCLK Rise Setup Time tCSS 60 ns SCLK Rise to CS Rise Hold Time tCSH 0 ns SDI Setup Time tDS 60 ns SDI Hold Time tDH 0 ns SCLK Rise to DOUT Valid Propagation Delay Time tDO1 CLOAD = 200pF 200 ns SCLK Fall to DOUT Valid Propagation Delay Time tDO2 CLOAD = 200pF 200 ns SCLK Rise to CS Fall Delay Time tCS0 10 ns CS Rise to SCLK Rise Hold Time tCS1 75 ns CS Pulse Width High tCSW 150 ns Note 1: Accuracy is guaranteed by the following table: Accuracy Guaranteed VDD (V) From Code: To Code: 5 16 4095 3 33 4095 Note 2: Offset is measured at the code closest to 10mV. Note 3: The temperature coefficient is determined by the "box" method, in which the maximum VOUT over the temperature range is divided by T and the typical reference voltage. Note 4: Accuracy is better than 1.0LSB for VOUT = 10mV to (VDD - 180mV). Guaranteed by PSR test on end points. Note 5: RLOAD = and digital inputs are at either VDD or DGND. _______________________________________________________________________________________ 5 MAX5122/MAX5123 TIMING CHARACTERISTICS--MAX5123 (+3V) Typical Operating Characteristics (VDD = +5V, RL = 5k, CL = 100pF, output amplifier in unity-gain configuration, TA = +25C, unless otherwise noted.) MAX5122 DIFFERENTIAL NONLINEARITY vs. DIGITAL INPUT CODE 0.10 DNL (LSB) 0.05 0.15 0 0 -0.05 -0.05 -0.10 -0.10 -0.15 -0.15 -0.20 1,000 2,000 3,000 4,000 2.500 2.495 0 1,000 2,000 3,000 4,000 -60 -40 5,000 -20 0 20 40 60 80 100 DIGITAL INPUT CODE DIGITAL INPUT CODE TEMPERATURE (C) MAX5122 SUPPLY CURRENT vs. TEMPERATURE MAX5122 SUPPLY CURRENT vs. SUPPLY VOLTAGE MAX5122 SHUTDOWN CURRENT vs. TEMPERATURE 350 (CODE = 000 HEX) 300 400 (CODE = AAA HEX) 350 (CODE = 000 HEX) 300 250 MAX5122/23 toc06 450 2.00 1.75 SHUTDOWN CURRENT (A) (CODE = AAA HEX) 400 MAX5122/23 toc05 450 500 SUPPLY CURRENT (A) MAX5122/23 toc04 500 1.50 1.25 1.00 0.75 0.50 0.25 250 200 -60 -40 -20 0 20 40 60 80 100 0 4.0 4.5 5.0 5.5 6.0 TEMPERATURE (C) SUPPLY VOLTAGE (V) MAX5122 FULL-SCALE OUTPUT VOLTAGE vs. TEMPERATURE MAX5122 FULL-SCALE OUTPUT ERROR vs. RESISTIVE LOAD -60 -40 -20 0 20 40 60 80 100 TEMPERATURE (C) MAX5122 DYNAMIC RESPONSE RISE TIME 2.505 2.500 2.495 0.25 FULL-SCALE OUTPUT ERROR (LSB) RL = 5k CL = 100pF MAX5122/23 toc07 MAX5122/23-09 2.510 MAX5122/23 toc08 SUPPLY CURRENT (A) 5,000 2.505 2.490 -0.20 0 CS 5V/div -0.50 OUT 1V/div -1.25 -2.00 2.490 -60 -40 -20 0 20 40 TEMPERATURE (C) 6 0.05 2.510 REFERENCE VOLTAGE (V) 0.10 MAX5122/23 toc02 0.15 INL (LSB) 0.20 MAX5122/23 toc01 0.20 MAX5122 REFERENCE VOLTAGE vs. TEMPERATURE MAX5122/23 toc03 MAX5122 INTEGRAL NONLINEARITY vs. DIGITAL INPUT CODE FULL-SCALE OUTPUT (V) MAX5122/MAX5123 +5V/+3V, 12-Bit, Serial, Force/Sense DACs with 10ppm/C Internal Reference 60 80 100 0.1 1 10 100 2s/div RL (k) _______________________________________________________________________________________ +5V/+3V, 12-Bit, Serial, Force/Sense DACs with 10ppm/C Internal Reference MAX5122 MAJOR CARRY TRANSITION MAX5122 DIGITAL FEEDTHROUGH (SCLK, OUT) MAX5122 DYNAMIC RESPONSE FALL TIME MAX5122/23-11 MAX5122/23-10 SCLK 2V/div CS 5V/div OUT 1V/div 5s/div MAX5123 DIFFERENTIAL NONLINEARITY vs. DIGITAL INPUT CODE 0.05 DNL (LSB) 0.10 0.05 0 0 -0.05 -0.10 -0.05 -0.10 -0.15 -0.15 -0.20 -0.25 -0.20 1,000 2,000 3,000 4,000 1.255 1.250 1.245 1.240 0 5,000 MAX5122/23 toc15 0.10 1.260 REFERENCE VOLTAGE (V) 0.15 MAX5122/23 toc14 0.20 MAX5123 REFERENCE VOLTAGE vs. TEMPERATURE 0.15 MAX5122/23 toc13 0.25 0 OUT 100mV/div AC COUPLED 2s/div MAX5123 INTEGRAL NONLINEARITY vs. DIGITAL INPUT CODE 1,000 2,000 3,000 4,000 5,000 -60 -40 -20 0 20 40 60 80 100 DIGITAL INPUT CODE DIGITAL INPUT CODE TEMPERATURE (C) MAX5123 SUPPLY CURRENT vs. TEMPERATURE MAX5123 SUPPLY CURRENT vs. SUPPLY VOLTAGE MAX5123 SHUTDOWN CURRENT vs. TEMPERATURE SUPPLY CURRENT (A) (CODE = AAA HEX) 300 (CODE = 000 HEX) 250 350 300 (CODE = 000 HEX) 250 200 -40 -20 0 20 40 TEMPERATURE (C) 60 80 100 0.4 0.3 0.2 0.1 200 -60 MAX5122/23 toc18 (CODE = AAA HEX) 350 0.5 SHUTDOWN CURRENT (A) 400 MAX5122/23 toc16 400 MAX5122/23 toc17 INL (LSB) CS 2V/div OUT 1mV/div AC COUPLED 2V/div SUPPLY CURRENT (A) MAX5122/23-12 2.50 2.75 3.00 3.25 SUPPLY VOLTAGE (V) 3.50 -60 -40 -20 0 20 40 60 80 100 TEMPERATURE (C) _______________________________________________________________________________________ 7 MAX5122/MAX5123 Typical Operating Characteristics (continued) (VDD = +5V, RL = 5k, CL = 100pF, output amplifier in unity-gain configuration, TA = +25C, unless otherwise noted.) Typical Operating Characteristics (continued) (VDD = +5V, RL = 5k, CL = 100pF, output amplifier in unity-gain configuration, TA = +25C, unless otherwise noted.) MAX5123 FULL-SCALE OUTPUT VOLTAGE vs. TEMPERATURE MAX5123 FULL-SCALE OUTPUT ERROR vs. RESISTIVE LOAD 1.250 1.245 1.240 MAX5122/23-21 MAX5122/23 toc20 1.255 -1 CS 2V/div -2 OUT 400mV/div -3 -4 -60 -40 -20 0 20 40 60 80 100 0.01 0.1 TEMPERATURE (C) 10 100 MAX5123 DIGITAL FEEDTHROUGH (SCLK, OUT) MAX5122/23-22 1s/div MAX5123 MAJOR CARRY TRANSITION MAX5122/23-23 MAX5122/23-24 SCLK 2V/div CS 2V/div CS 2V/div OUT 500V/div AC COUPLED OUT 400mV/div 1s/div 1 RL (k) MAX5123 DYNAMIC-RESPONSE FALL TIME 8 MAX5123 DYNAMIC-RESPONSE RISE TIME 0 FULL-SCALE OUTPUT ERROR (LSB) MAX5122/23 toc19 1.260 FULL-SCALE OUTPUT (V) MAX5122/MAX5123 +5V/+3V, 12-Bit, Serial, Force/Sense DACs with 10ppm/C Internal Reference 2s/div OUT 100mV/div AC COUPLED 5V/div _______________________________________________________________________________________ +5V/+3V, 12-Bit, Serial, Force/Sense DACs with 10ppm/C Internal Reference PIN NAME FUNCTION 1 FB 2 OUT Analog Output Voltage. High impedance if part is in shutdown. 3 RSTVAL Reset Value Input (Digital Input). 1: Connect to VDD to select midscale as the output reset value. 0: Connect to DGND to select 0V as the output reset value. 4 PDL Power-Down Lockout (Digital Input). 1: Normal operation. 0: Disallows shutdown (device cannot be powered down). 5 CLR Reset DAC Input (Digital Input). Clears the DAC to its predetermined (RSTVAL) output state. Clearing the DAC will cause it to exit a software shutdown state. 6 CS Active-Low Chip-Select Input (Digital Input) 7 DIN Serial Data Input. Data is clocked in on the rising edge of SCLK. 8 SCLK Serial Clock Input 9 DGND Digital Ground 10 DOUT Serial Data Output 11 UPO 12 PD 13 AGND 14 REF 15 REFADJ 16 VDD Amplifier Inverting Sense Input (Analog Input) User-Programmable Output (Digital Output) Power-Down Input (Digital Input). Pulling PD high when PDL = VDD places the IC into shutdown with a maximum shutdown current of 20A. Analog Ground Buffered Reference Output/Input. In internal reference mode, the reference buffer provides a +2.5V (MAX5122) or +1.25V (MAX5123) nominal output, externally adjustable at REFADJ. In external reference mode, disable the internal reference by pulling REFADJ to VDD and applying the external reference to REF. Analog Reference Adjust Input. Bypass with a 33nF capacitor to AGND. Connect to VDD when using an external reference. Positive Power Supply. Bypass with a 0.1F capacitor in parallel with a 4.7F capacitor to AGND. _______________________________________________________________________________________ 9 MAX5122/MAX5123 Pin Description MAX5122/MAX5123 +5V/+3V, 12-Bit, Serial, Force/Sense DACs with 10ppm/C Internal Reference CS PDL PD VDD AGND DGND DIN SCLK SR CONTROL DOUT 16-BIT SHIFT REGISTER RSTVAL LOGIC OUTPUT UPO DECODE CONTROL CLR FB 12 MAX5122 MAX5123 BANDGAP 1.25V REFERENCE INPUT REGISTER 2X (X1) 4k DAC REGISTER OUT DAC 2.5V (1.25V) REFERENCE BUFFER REFADJ REF ( ) ARE FOR MAX5123 ONLY. Figure 1. Simplified Functional Diagram _______________Detailed Description The MAX5122/MAX5123 12-bit, force/sense DACs are easily configured with a 3-wire serial interface. They include a 16-bit data-in/data-out shift register and have a double-buffered digital input consisting of an input register and a DAC register. In addition, these devices employ precision bandgap references, as well as an output amplifier with accessible feedback and output pins that can be used to set the gain externally (Figure 1) or for forcing and sensing applications. These DACs are designed with an inverted R-2R ladder network (Figure 2) that produces a weighted voltage proportional to the digital input code. Internal Reference Both devices use an on-board precision bandgap reference with a low temperature coefficient of only 10ppm/C (max) to generate an output voltage of +2.5V (MAX5122) or +1.25V (MAX5123). The REF pin can source up to 100A and may become unstable with capacitive loads exceeding 100pF. REFADJ can be used for minor adjustments to the reference voltage. FB R 2R 2R D0 R 2R D9 OUT R 2R D10 2R D11 REF* AGND NOTE: SHOWN FOR ALL 1s ON DAC. *INTERNAL REFERENCE: +2.5V (MAX5122), +1.25V (MAX5123); OR EXTERNAL REFERENCE Figure 2. Simplified Inverted R-2R DAC Structure 10 ______________________________________________________________________________________ +5V/+3V, 12-Bit, Serial, Force/Sense DACs with 10ppm/C Internal Reference External Reference An external reference may be applied to the REF pin. Disable the internal reference by pulling REFADJ to VDD. This allows an external reference signal (AC- or DC-based) to be fed into the REF pin. For proper operation, do not exceed the input voltage range limits of 0 to (VDD - 1.4V) for VREF. Determine the output voltage using the following equation (REFADJ = VDD): VOUT = VREF [(NB / 4096) G] where NB is the numeric value of the MAX5122/ MAX5123 input code (0 to 4095), VREF is the external reference voltage, and G is the gain of the output amplifier, set by an external resistor-divider. The REF pin has a minimum input resistance of 40k and is code-dependent. Output Amplifier The MAX5122/MAX5123's DAC output is internally buffered by a precision amplifier with a typical slew rate of 0.6V/s. Access to the output amplifier's inverting input (FB) provides the user greater flexibility with amplifier gain setting and signal conditioning (see Applications Information). The output amplifier typically settles to 0.5LSB from a full-scale transition within 20s when it is connected in unity gain and loaded with 5k 100pF. Loads less than 1k may result in degraded performance. Power-Down Mode These devices feature software- and hardware-programmable (PD pin) shutdown modes that reduce the typical supply current to 3A. To enter software shutdown mode, program the control sequence for the DAC as shown in Table 1. In shutdown mode, the amplifier output becomes highimpedance and the serial interface remains active. Data in the input registers is saved, allowing the MAX5122/MAX5123 to recall the output state prior to entering shutdown when returning to normal operation. To exit shutdown mode, load both input and DAC registers simultaneously or update the DAC register from the input register. When returning from shutdown to normal operation, wait 2ms for the reference to settle. When using an external reference, the DAC requires only 20s for the output to stabilize. +3V +5V MAX5122 90k 400k 400k 100k MAX5123 15k REFADJ 33nF Figure 3a. MAX5122 Reference Adjust Circuit 100k REFADJ 33nF Figure 3b. MAX5123 Reference Adjust Circuit ______________________________________________________________________________________ 11 MAX5122/MAX5123 The circuit in Figure 3 achieves a nominal reference adjustment range of 1%. Connect a 33nF capacitor from REFADJ to AGND to establish low-noise DAC operation. Larger capacitor values may be used, but will result in increased start-up delay. The time constant () for the start-up delay is determined by the REFADJ input impedance of 4k and CREFADJ: = 4k * CREFADJ MAX5122/MAX5123 +5V/+3V, 12-Bit, Serial, Force/Sense DACs with 10ppm/C Internal Reference Table 1. Serial-Interface Programming Commands 16-BIT SERIAL WORD S0* FUNCTION C2 C1 C0 D11 ............... D0 S0* 0 0 0 XXXXXXXXXXXX 0 No operation. 0 0 1 12-Bit DAC Data 0 Load input register; DAC register unchanged. 0 1 0 12-Bit DAC Data 0 Simultaneously load input and DAC registers; exit shutdown. 0 1 1 XXXXXXXXXXXX 0 Update DAC register from input register; exit shutdown. 1 0 1 XXXXXXXXXXXX 0 Shutdown DAC (provided PDL = 1). 1 0 0 XXXXXXXXXXXX 0 UPO goes low (default). 1 1 0 XXXXXXXXXXXX 0 UPO goes high. 1 1 1 1XXXXXXXXXXX 0 Mode 1; DOUT clocked out on SCLK's rising edge. 1 1 1 00XXXXXXXXXX 0 Mode 0; DOUT clocked out on SCLK's falling edge (default). X = Don't care * S0 is a sub-bit and always zero. Power-Down Lockout Input (PDL) The power-down lockout pin (PDL) disables shutdown when low. When in shutdown mode, a high-to-low transition on PDL will wake up the DAC with its output still set to the state prior to power-down. PDL can also be used to wake up the device asynchronously. Power-Down Input (PD) Pulling PD high places the MAX5122/MAX5123 in shutdown. Pulling PD low will not return the MAX5122/ MAX5123 to normal operation. A high-to-low transition on PDL or appropriate commands (Table 1) via the serial interface are required to exit power-down mode. Serial-Interface Configuration (SPI/QSPI/MICROWIRE/PIC16/PIC17) The MAX5122/MAX5123 3-wire serial interface is compatible with SPI, QSPI, PIC16/PIC17 (Figure 4) and MICROWIRE (Figure 5) interface standards. The 2byte-long serial input word contains three control bits, 12 data bits in MSB-first format, and one sub-bit, which is always zero (Table 2). The MAX5122/MAX5123's digital inputs are double buffered, which allows the user to: * Load the input register without updating the DAC register, * Update the DAC register with data from the input register, * Update the input and DAC registers concurrently. VDD SS DIN MAX5122 MAX5123 SCLK CS ( ) ARE FOR PIC16/PIC17 ONLY. MOSI SCK SPI/QSPI PORT (PIC16/PIC17) I/O CPOL = 0, CPHA = 0 (CKE = 1, CKP = 0, SMP= 0 SSPM3 - SSPM0 = 0001) Figure 4. SPI/QSPI Interface Connections (PIC16/PIC17) SCLK MAX5122 MAX5123 SK MICROWIRE PORT DIN SO CS I/O Figure 5. MICROWIRE Interface Connections 12 ______________________________________________________________________________________ +5V/+3V, 12-Bit, Serial, Force/Sense DACs with 10ppm/C Internal Reference MAX5122 and 6.6MHz for the MAX5123. Figure 7 depicts a more detailed timing diagram of the serial interface. * The state of the user-programmable logic output, * The configuration of the device after shutdown. The general timing diagram in Figure 6 illustrates how data is acquired. CS must be low for the part to receive data. With CS low, data at DIN is clocked into the register on the rising edge of SCLK. When CS transitions high, data is latched into the input and/or DAC registers, depending on the setting of the three control bits C2, C1, and C0. The maximum serial clock frequency guaranteed for proper operation is 10MHz for the The MAX5122/MAX5123 are compatible with a PIC16/PIC17 microcontroller (C), using the synchronous serial port (SSP) module. To establish SPI communication, connect the controller as shown in Figure 4 and configure the PIC16/PIC17 as system master by initializing its synchronous serial port control register (SSPCON) and synchronous serial port status register (SSPSTAT) to the bit patterns shown in Tables 3 and 4. In SPI mode, the PIC16/PIC17 Cs allow eight bits of data to be synchronously transmitted and received simultaneously. Two consecutive 8-bit writings (Figure 6) are necessary to feed the DAC with three control bits, 12 data bits, and one sub-bit. DIN data transitions on the serial clock's falling edge and is clocked into the DAC on SCLK's rising edge. The first eight bits of DIN contain the three control bits (C2, C1, C0) and the first five data bits (D11-D7). The second 8-bit data stream contains the remaining bits (D6-D0), and the sub-bit S0. PIC16 with SSP Module and PIC17 Interface Table 2. Serial Data Format MSB ............................................................................ LSB 16 BITS OF SERIAL DATA Control Bits MSB...Data Bits...LSB C2, C1, C0 D11....................D0 Sub-Bit S0 CS COMMAND EXECUTED SCLK 1 DIN C2 8 C1 C0 D11 D10 D9 D8 D7 9 D6 16 D5 D4 D3 D2 D1 D0 S0 Figure 6. Serial-Interface Timing tCSW CS tCS0 tCSH tCSS tCS1 SCLK tCH tCL tCP DIN tDS tDO1 tDO2 tDH DOUT Figure 7. Detailed Serial-Interface Timing ______________________________________________________________________________________ 13 MAX5122/MAX5123 The 16-bit input word may be sent in two 1-byte packets (SPI-, MICROWIRE-, and PIC16/PIC17-compatible), with CS low during this period. The control bits C2, C1, and C0 (table 1) determine: * The clock edge on which DOUT transitions, MAX5122/MAX5123 +5V/+3V, 12-Bit, Serial, Force/Sense DACs with 10ppm/C Internal Reference Table 3. Detailed SSPCON Register Contents CONTROL BIT MAX5122/MAX5123 SETTINGS SYNCHRONOUS SERIAL-PORT CONTROL REGISTER (SSPCON) WCOL BIT7 X Write Collision Detection Bit SSPOV BIT6 X Receive Overflow Detect Bit SSPEN BIT5 1 Synchronous Serial Port Enable Bit. 0: Disables serial port and configures these pins as I/O port pins. 1: Enables serial port and configures SCK, SDO and SCI as serialport pins. Clock Polarity Select Bit. CKP = 0 for SPI master-mode selection. CKP BIT4 0 SSPM3 BIT3 0 SSPM2 BIT2 0 SSPM1 BIT1 0 SSPM0 BIT0 1 Synchronous Serial Port Mode Select Bit. Sets SPI master mode and selects fCLK = fOSC / 16 X = Don't care Table 4. Detailed SSPSTAT Register Contents CONTROL BIT MAX5122/MAX5123 SETTINGS SYNCHRONOUS SERIAL-PORT CONTROL REGISTER (SSPSTAT) SMP BIT7 0 SPI Data Input Sample Phase. Input data is sampled at the middle of the data output time. CKE BIT6 1 SPI Clock Edge Select Bit. Data will be transmitted on the rising edge of the serial clock. D/A BIT5 X Data Address Bit P BIT4 X Stop Bit S BIT3 X Start Bit R/W BIT2 X Read/Write Bit Information UA BIT1 X Update Address BF BIT0 X Buffer Full Status Bit X = Don't care Serial Data Output User-Programmable Output (UPO) The contents of the internal shift-register are output serially on DOUT which allows for daisy-chaining of multiple devices (see Applications Information) as well as data readback. The MAX5122/MAX5123 may be programmed to shift data out of DOUT on the serial clock's rising edge (Mode 1) or on the falling edge (Mode 0). The latter is the default during power-up and provides a lag of 16 clock cycles, maintaining SPI, QSPI, MICROWIRE, and PIC16/PIC17 compatibility. In Mode 1, the output data lags DIN by 15.5 clock cycles. During power-down, DOUT retains its last digital state prior to shutdown. The UPO feature allows an external device to be controlled through the serial-interface setup (Table 1) thereby reducing the number of microcontroller I/O ports required. During power-down, this output will retain the last digital state before shutdown. With CLR pulled low, UPO will reset to the default state after wake-up. 14 ______________________________________________________________________________________ +5V/+3V, 12-Bit, Serial, Force/Sense DACs with 10ppm/C Internal Reference Definitions Integral Nonlinearity (INL) Integral nonlinearity (Figure 8a) is the deviation of the values on an actual transfer function from a straight line. This straight line can be either a best-straight-line fit (closest approximation to the actual transfer curve) or a line drawn between the endpoints of the transfer function, once offset and gain errors have been nullified. For a DAC, the deviations are measured at every single step. Differential Nonlinearity (DNL) Differential nonlinearity (Figure 8b) is the difference between an actual step height and the ideal value of 1LSB. If the magnitude of the DNL is less than or equal to 1LSB, the DAC guarantees no missing codes and is monotonic. Offset Error The offset error (Figure 8c) is the difference between the ideal and the actual offset point. For a DAC, the offset point is the step value when the digital input is zero. This error affects all codes by the same amount and can usually be compensated for by trimming. Gain Error Gain error (Figure 8d) is the difference between the ideal and the actual full-scale output voltage on the transfer curve, after nullifying the offset error. This error alters the slope of the transfer function and corresponds to the same percentage error in each step. 7 ACTUAL DIAGRAM ANALOG OUTPUT VALUE (LSB) ANALOG OUTPUT VALUE (LSB) 3 6 5 4 AT STEP O11 (1/2 LSB ) 3 2 AT STEP 001 (1/4 LSB ) 1 ACTUAL OFFSET POINT 0 000 001 010 011 100 101 110 2 IDEAL DIAGRAM OFFSET ERROR (+1 1/4 LSB) 1 IDEAL OFFSET POINT 0 111 000 001 DIGITAL INPUT CODE Figure 8a. Integral Nonlinearity IDEAL FULL-SCALE OUTPUT 7 1 LSB 5 DIFFERENTIAL LINEARITY ERROR (-1/4 LSB) 4 3 1 LSB 2 DIFFERENTIAL LINEARITY ERROR (+1/4 LSB) 0 ANALOG OUTPUT VALUE (LSB) ANALOG OUTPUT VALUE (LSB) 011 Figure 8c. Offset Error 6 1 010 DIGITAL INPUT CODE GAIN ERROR (-1 1/4 LSB) 6 IDEAL DIAGRAM ACTUAL FULL-SCALE OUTPUT 5 4 0 000 001 010 011 100 101 000 100 DIGITAL INPUT CODE Figure 8b. Differential Nonlinearity 101 110 111 DIGITAL INPUT CODE Figure 8d. Gain Error ______________________________________________________________________________________ 15 MAX5122/MAX5123 __________Applications Information MAX5122/MAX5123 +5V/+3V, 12-Bit, Serial, Force/Sense DACs with 10ppm/C Internal Reference Settling Time The settling time is the amount of time required from the start of a transition until the DAC output settles to its new output value within the converter's specified accuracy. +5V/+3V REF VDD 50k MAX5122 MAX5123 Digital Feedthrough Digital feedthrough is noise generated on the DAC's output when any digital input transitions. Proper board layout and grounding will significantly reduce this noise, but there will always be some feedthrough caused by the DAC itself. FB 50k DAC OUT AGND DGND Unipolar Output Figure 9 shows the MAX5122/MAX5123 setup for unipolar, rail-to-rail operation with a closed- loop gain of 2V/V. With its internal reference of +2.5V, the MAX5122 provides a convenient unipolar output range of 0 to +4.99878V, while the MAX5123 offers an output range of 0 to +2.49939V with its on-board +1.25V reference. Table 5 lists example codes for unipolar output voltages. NOTE: GAIN = +2V/V Figure 9. Unipolar Output Circuit Using Internal (+1.25V/+2.5V) or External Reference. With external reference, pull REFADJ to VDD. Bipolar Output The MAX5122/MAX5123 can be configured for unitygain bipolar operation (FB = OUT) using the circuit shown in Figure 10. The output voltage VOUT is then given by the following equation: VOUT = VREF [{G (NB / 4096)} - 1] where NB is the numeric value of the DAC's binary input code, VREF is the voltage of the internal (or external) precision reference, and G is the overall gain. The application circuit in Figure 10 uses a low-cost op amp (MAX4162) external to the MAX5122/MAX5123. Together with the MAX5122/MAX5123 this circuit offers an overall gain of +2V/V. Table 6 lists example codes for bipolar output voltages. Reset (RSTVAL) and Clear (CLR ) Functions The MAX5122/MAX5123 DACs feature a clear pin (CLR), which resets the output to a certain value, depending upon how RSTVAL is set. RSTVAL = DGND selects an output of 0, and RSTVAL = VDD selects a midscale output when CLR is pulled low. The CLR pin has a minimum input resistance of 40k in series with a diode to the supply voltage (VDD). If the digital voltage is higher than the supply voltage for the part, a small input current may flow, but this current will be limited to (V CLR - VDD - 0.5V) / 40k. Note: Clearing the DAC will also cause the part to exit a software shutdown (PD = 0). 16 +5V/+3V 50k 50k REF VDD FB MAX5122 MAX5123 V+ VOUT DAC OUT DGND AGND V- MAX4162 Figure 10. Unity-Gain Bipolar Output Circuit Using Internal (+1.25V/+2.5V) or External Reference. With external reference, pull REFADJ to VDD. Daisy-Chaining Devices Any number of MAX5122/MAX5123s may be daisychained by simply connecting the serial data output pin (DOUT) of one device to the serial data input pin (DIN) of the following device in the chain (Figure 11). Another configuration (Figure 12) allows several MAX5122/MAX5123 DACs to share one common DIN signal line. In this configuration, the data bus is common to all devices; data is not shifted through a daisy-chain. However, more I/O lines are required in this configuration, because each IC needs a dedicated CS line. ______________________________________________________________________________________ +5V/+3V, 12-Bit, Serial, Force/Sense DACs with 10ppm/C Internal Reference MAX5122/MAX5123 Table 5. Unipolar Code Table (Figure 9) DAC CONTENTS ANALOG OUTPUT INTERNAL REFERENCE SUB-BIT S0 MAX5122 MAX5123 EXTERNAL REFERENCE MAX5122/MAX5123 1111 1111 1111 0 +4.99878V +2.49939V VREF (4095 / 4096) 2 1000 0000 0001 0 +2.50122V +1.25061V VREF (2049 / 4096) 2 1000 0000 0000 0 +2.5V +1.25V VREF (2048 / 4096) 2 0111 1111 1111 0 +2.49878V +1.24939V VREF (2047 / 4096) 2 0000 0000 0001 0 +1.2207mV +610.35V VREF (1 / 4096) 2 0000 0000 0000 0 0V 0V 0 MSB LSB Table 6. Bipolar Code Table (Figure 10) DAC CONTENTS MSB ANALOG OUTPUT INTERNAL REFERENCE SUB-BIT S0 LSB MAX5122 MAX5123 EXTERNAL REFERENCE MAX5122/MAX5123 1111 1111 1111 0 +2.49878V +1.24939V VREF [ {2 (4095 / 4096)} - 1] 1000 0000 0001 0 +1.2207mV +610.35V VREF [ {2 (2049 / 4096)} - 1] 1000 0000 0000 0 0V 0V VREF [ {2 (2048 / 4096)} - 1] 0111 1111 1111 0 -1.2207mV -610.35V VREF [ {2 (2047 / 4096)} - 1] 0000 0000 0001 0 -2.49878V -1.24939V VREF [ {2 (1 / 4096)} - 1] 0000 0000 0000 0 -2.5V -1.25V -VREF SCLK DIN CS SCLK SCLK I II III MAX5122 MAX5123 MAX5122 MAX5123 MAX5122 MAX5123 DOUT DIN DOUT CS DIN CS DOUT TO OTHER SERIAL DEVICES Figure 11. Daisy-Chaining Multiple Devices with the Digital I/Os DIN/DOUT ______________________________________________________________________________________ 17 MAX5122/MAX5123 +5V/+3V, 12-Bit, Serial, Force/Sense DACs with 10ppm/C Internal Reference V DD ). Bypass the power supply (VDD) with a 4.7F capacitor in parallel with a 0.1F capacitor to AGND. Minimize lead lengths to reduce lead inductance. Using an External Reference with AC Components The MAX5122/MAX5123 have multiplying capabilities within the reference input voltage range specifications. Figure 13 shows a technique for applying a sinusoidal input to REF, where the AC signal is offset before being applied to the reference input. Layout Considerations Digital and AC signals coupling to AGND can create noise at the output. Connect AGND to the highest quality ground available. Use proper grounding techniques, such as a multilayer board with a low-inductance ground plane. Wire-wrapped boards and sockets are not recommended. If noise becomes an issue, shielding may be required. Power-Supply and Bypassing Considerations On power-up, the input and DAC registers are cleared to either zero (RSTVAL = DGND) or midscale (RSTVAL = DIN SCLK CS1 CS2 TO OTHER SERIAL DEVICES CS3 I CS II CS MAX5122 MAX5123 III CS MAX5122 MAX5123 MAX5122 MAX5123 SCLK SCLK SCLK DIN DIN DIN Figure 12. Multiple Devices Share One Common Digital Input (DIN) ___________________Chip Information +5V/ +3V TRANSISTOR COUNT: 3308 SUBSTRATE CONNECTED TO AGND +5V/+3V 26k AC REFERENCE INPUT 500mVp-p MAX495 10k REF VDD FB DAC OUT MAX5122 MAX5123 AGND DGND Figure 13. External Reference with AC Components 18 ______________________________________________________________________________________ +5V/+3V, 12-Bit, Serial, Force/Sense DACs with 10ppm/C Internal Reference QSOP.EPS PACKAGE OUTLINE, QSOP .150", .025" LEAD PITCH 21-0055 F 1 1 Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. 19 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 (c) 2006 Maxim Integrated Products Printed USA is a registered trademark of Maxim Integrated Products, Inc. MAX5122/MAX5123 Package Information (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information, go to www.maxim-ic.com/packages.)