512Mb DDR SDRAM
HY5DU12422A(L)T
HY5DU12822A(L)T
HY5DU121622A(L)T
This document is a general product description and is subject to change without notice. Hynix s emic onduc tor does not assume
any responsibility for use of circuits described. No patent lic enses are implied.
Rev. 0.4/Feb. 2003 1
HY5DU12422A(L)T
HY5DU12822A(L)T
HY5DU121622A(L)T
Rev. 0.4/Feb. 2003 2
HY5DU12422A(L)T
HY5DU12822A(L)T
HY5DU121622A(L)T
Revision History
Revision
No. History Draft Date Remark
0.0 1) Datasheet Release in Preliminary version Nov. 2003
0.1 1) Correction of typo in page 3,19,29,31
2) Change IDD value Dec. 26. 2003
0.2 1) Correction of tLZ/tHZ in AC Characteristics Dec. 30. 2003
0.3 1) Correction of IDD value
2) Insert DC test timing pattern for DDR400/DDR333 Jan. 2003
0.4 1) Separated DDR400 Speed part. Feb. 2003
DESCRIPTION
The HY5DU12422A(L)T, HY5DU12822A(L)T and HY5DU121622A(L)T are a 536,870,912-bit CMOS Double Data
Rate(DDR) Synchronous DRAM, ideally suited for the main memory applications which requires large memory density
and high bandwidth.
This Hynix 512Mb DDR SDRAMs offer fully synchronous operations referenced to both rising and falling edges of the
clock. While all addresses and contro l inputs ar e latched on th e rising edges of the CK (falling edg es of the /CK), Data,
Data strobes and W rite data mas ks inputs ar e samp led on both rising and falling edges of it. The data paths are inter-
nally pipelined and 2-bit prefetched to achieve very high ban dwid th. All inp ut and output voltage levels are compatible
with SSTL_2.
FEATURES
•VDD, VDDQ = 2.5V +/- 0.2V
All inputs and outputs are compatible with SSTL_2
interface
Fully differential clock inputs (CK, /CK) operation
Double data rate interface
Source synchronous - data transaction aligned to
bidirectional data strobe (DQS)
x16 device has two bytewide data strobes (UDQS,
LDQS) per each x8 I/O
Data outputs on DQS edges when read (edged DQ)
Data inputs on DQS centers when write (centered
DQ)
On chip DLL align DQ and DQS transition with CK
transition
DM mask write data-in at the both rising and falling
edges of the data strobe
All addresses and control inputs except data, data
strobes and data masks latched on the rising edges
of the clock
Programmable /CAS latency 2 / 2.5 supported
Programmable burst length 2 / 4 / 8 with both
sequential and interleave mode
Internal four bank operations with single pulsed
/RAS
Auto refresh and self refresh supported
tRAS lock out function supported
8192 refresh cycles / 64ms
JEDEC standard 4 00mil 66pin TSOP-II with 0.65mm
pin pitch
Full and Half strength driver option controlled by
EMRS
ORDERING INFORMATION
* X means speed grade
Part No. Configuration Package
HY5DU12422A(L)T-X* 128Mx4 400mil
66pin
TSOP-II
HY5DU12822A(L)T-X* 64Mx8
HY5DU121622A(L)T-X* 32Mx16
Rev. 0.4/Feb. 2003 3
OPERATING FREQUENCY
Grade CL2 CL2.5 Remark
(CL-tRCD-tRP)
- J 133MHz 166MHz DDR333 (2.5-3-3)
- M 133MHz 133MHz DDR266 (2-2-2)
- K 133MHz 133MHz DDR266A (2-3-3)
- H 100MHz 133MHz DDR266B (2.5-3-3)
- L 100MHz 125MHz DDR200 (2-2-2)
HY5DU12422A(L)T
HY5DU12822A(L)T
HY5DU121622A(L)T
Rev. 0.4/Feb. 2003 4
HY5DU12422A(L)T
HY5DU12822A(L)T
HY5DU121622A(L)T
PIN CONFIGURATION
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
VDD
DQ0
VDDQ
DQ1
DQ2
VSSQ
DQ3
DQ4
VDDQ
DQ5
DQ6
VSSQ
DQ7
NC
VDDQ
LDQS
NC
VDD
NC
LDM
/WE
/CAS
/RAS
/CS
NC
BA0
BA1
A10/AP
A0
A1
A2
A3
VDD
VSS
DQ15
VSSQ
DQ14
DQ13
VDDQ
DQ12
DQ11
VSSQ
DQ10
DQ9
VDDQ
DQ8
NC
VSSQ
UDQS
NC
VREF
VSS
UDM
/CK
CK
CKE
NC
A12
A11
A9
A8
A7
A6
A5
A4
VSS
VDD
DQ0
VDDQ
NC
DQ1
VSSQ
NC
DQ2
VDDQ
NC
DQ3
VSSQ
NC
NC
VDDQ
NC
NC
VDD
NC
NC
/WE
/CAS
/RAS
/CS
NC
BA0
BA1
A10/AP
A0
A1
A2
A3
VDD
VSS
DQ7
VSSQ
NC
DQ6
VDDQ
NC
DQ5
VSSQ
NC
DQ4
VDDQ
NC
NC
VSSQ
DQS
NC
VREF
VSS
DM
/CK
CK
CKE
NC
A12
A11
A9
A8
A7
A6
A5
A4
VSS
VDD
NC
VDDQ
NC
DQ0
VSSQ
NC
NC
VDDQ
NC
DQ1
VSSQ
NC
NC
VDDQ
NC
NC
VDD
NC
NC
/WE
/CAS
/RAS
/CS
NC
BA0
BA1
A10/AP
A0
A1
A2
A3
VDD
VSS
NC
VSSQ
NC
DQ3
VDDQ
NC
NC
VSSQ
NC
DQ2
VDDQ
NC
NC
VSSQ
DQS
NC
VREF
VSS
DM
/CK
CK
CKE
NC
A12
A11
A9
A8
A7
A6
A5
A4
VSS
x16 x8 x4x4 x8 x16
400mil X 875mil
66pin TSOP -II
0.65mm pin pitch
ROW AND COLUMN ADDRESS TABLE
ITEMS 128Mx4 64Mx8 32Mx16
Organization 32M x 4 x 4banks 16M x 8 x 4banks 8M x 16 x 4banks
Row Address A0 - A12 A0 - A12 A0 - A12
Column Address A0-A9, A11, A12 A0-A9, A11 A0-A9
Bank Address BA0, BA1 BA0, BA1 BA0, BA1
Auto Precharge Flag A10 A10 A10
Refresh 8K 8K 8K
Rev. 0.4/Feb. 2003 5
HY5DU12422A(L)T
HY5DU12822A(L)T
HY5DU121622A(L)T
PIN DESCRIPTION
PIN TYPE DESCRIPTION
CK, /CK Input Clock: CK and /CK are differential clock inputs. All address and control input signals are
sampled on the crossing of the positive edge of CK and negative edge of /CK. Output
(read) data is referenced to the crossings of CK and /CK (both directions of crossing ).
CKE Input
Clock Enable: CKE HIGH activates, and CKE LOW deactiv ates internal clock signals, and
device input buffers and output drivers. Taking CKE LOW provides PRECHARGE POWER
DOWN and SELF REFRESH operation (all banks idle), or ACTIVE POWER DOWN (row
ACTIVE in any bank). CKE is synchronous for POWER DOWN entry and exit, and for SELF
REFRESH entry. CKE is asynchronous for SELF REFRESH exit, and for ou tput disab le. CKE
must be maintained high throughout READ and WRITE accesses. Input buff ers, excluding
CK, /CK and CKE are disabled during POWER DOWN. Input buffers, excluding CKE are
disabled during SELF REFRESH. CKE is an SSTL_2 input, but will detect an LVCMOS LOW
level after Vdd is applied.
/CS Input Chip Select : Enables or disables all inputs except CK, /CK, CKE, DQS and DM. All com-
mands are masked when CS is registered high. CS provides for external bank selection on
systems with multiple banks. CS is cons id ered part of the command code.
BA0, BA1 Input Bank Addr es s I nput s: B A0 and BA1 def ine to which bank an ACTIVE, R ead, W rite or PRE-
CHARGE command is being applied.
A0 ~ A12 Input
Address Input s: Provid e the row ad dress f or ACTIVE co mmands, and the column address
and AUT O PR ECHARGE bit f o r READ/WRITE comman ds, to s elect one lo cati on ou t of the
memory array in the respective bank. A10 is sampled during a precharge command to
determine whether the PRECHARGE applies to one bank (A10 LOW) or all banks (A10
HIGH). If only one bank is to be precharged, the bank is selected by BA0, BA1. The
address inputs also provide the op code during a MODE REGISTER SET command. BA0
and BA1 define which mod e register is loaded during th e MODE REGISTER SET command
(MRS or EMRS).
/RAS, /CAS, /WE Input Command Inpu ts: /RAS, /CAS and /WE (along with /CS) define the command being
entered.
DM
(LDM,UDM) Input
Input Data Mask: DM is an input mask signal for write data. Inpu t data is masked when
DM is sampled HIGH along with that inpu t data during a WRITE acces s. DM is sampled
on both ed ges of D QS . Al thou gh D M pi ns are input only, the DM loading matches the DQ
and DQS loading. For the x16, LDM corresponds to the data on DQ0-Q7; UDM corre-
sponds to the data on DQ8-Q15.
DQS
(LDQS,UDQS) I/O Data Strobe: Output with read data, input with write data. Edge aligned with read data,
centered in write data. Used to capture write data. For the x16, LDQS corresponds to the
data on DQ0-Q7; UDQS co rresponds to the data on DQ8-Q15.
DQ I/O Data input / output pin : Data bus
VDD/VSS Supply Power supply for internal circuits and input buffers.
VDDQ/VSSQ Supply Power supply for output buffers for noise immunity.
VREF Supply Reference voltage for inputs for SSTL interface.
NC NC No connection.
Rev. 0.4/Feb. 2003 6
HY5DU12422A(L)T
HY5DU12822A(L)T
HY5DU121622A(L)T
Command
Decoder
CLK
/CLK
CKE
/CS
/RAS
/CAS
/WE
DM
Address
Buffer
A0~A12
Bank
Control 32Mx4/Bank0
Colum n Decoder
Colum n Address
Counter
Sense AM P
2-bit Prefetch Unit
32Mx4/Bank1
32Mx4/Bank2
32Mx4/Bank3
Mode
Register Row
Decoder
Input Buffer Output Buffer
DLL
Block
Mode
Register
Data Strobe
Transmitter
Data Strobe
Receiver
DQS
CLK
/CLK
DS
W rite Data Register
2-bit Prefetch Unit DS
DQ [0:3]
84
4
8
CLK_DLL
BA0, BA1
FUNCTIONAL BLOCK DIAGRAM (128Mx4)
4Banks x 32Mbit x 4 I/O Double Data Rate Synchronous DRAM
Rev. 0.4/Feb. 2003 7
HY5DU12422A(L)T
HY5DU12822A(L)T
HY5DU121622A(L)T
Command
Decoder
CLK
/CLK
CKE
/CS
/RAS
/CAS
/WE
DM
Address
Buffer
A0~A12
Bank
Control 16Mx8/Bank0
Colum n Decoder
Colum n Address
Counter
Sense AM P
2-bit Prefetch Unit
16Mx8/Bank1
16Mx8/Bank2
16Mx8/Bank3
Mode
Register Row
Decoder
Input Buffer Output Buffer
DLL
Block
Mode
Register
Data Strobe
Transmitter
Data Strobe
Receiver
DQS
CLK
/CLK
DS
W rite Data Register
2-bit Prefetch Unit DS
DQ [0:7]
16 8
8
16
CLK_DLL
BA0,BA1
FUNCTIONAL BLOCK DIAGRAM (64Mx8)
4Banks x 16Mbit x 8 I/O Double Data Rate Synchronous DRAM
Rev. 0.4/Feb. 2003 8
HY5DU12422A(L)T
HY5DU12822A(L)T
HY5DU121622A(L)T
Command
Decoder
CLK
/CLK
CKE
/CS
/RAS
/CAS
/WE
LDM
Address
Buffer
A0~A12
Bank
Control 8Mx16/Bank0
Colum n Decoder
Colum n Address
Counter
Sense AM P
2-bit Prefetch Unit
8Mx16/Bank1
8Mx16/Bank2
8Mx16/Bank3
Mode
Register Row
Decoder
Input Buffer Output Buffer
DLL
Block
Mode
Register
Data Strobe
Transmitter
Data Strobe
Receiver
LDQS, UDQS
CLK
/CLK
LDQS
UDQS
W rite Data Register
2-bit Prefetch Unit DS
DQ[0:15]
32 16
16
32
CLK_DLL
BA0, BA1
UDM
FUNCTIONAL BLOCK DIAGRAM (32Mx16)
4Banks x 8Mbit x 16 I/O Double Data Rate Synchronous DRAM
Rev. 0.4/Feb. 2003 9
HY5DU12422A(L)T
HY5DU12822A(L)T
HY5DU121622A(L)T
SIMPLIFIED COMMAND TRUTH TABLE
Command CKEn-1 CKEn CS RAS CAS WE ADDR A10/
AP BA Note
Extended Mode Register SetH XLLLL OP code 1,2
Mode Register Set H XLLLL OP code 1,2
Device Deselect HX
HXXX X1
No Operation L H H H
Bank Active H X L L H H RA V 1
Read HXLHLHCA
LV1
Read with Autoprecharge H1,3
Write HXLHLLCA
LV1
Write with Au to precharge H1,4
Precharge All Banks HXLLHLX
HX1,5
Precharge selected Bank LV1
Read Burst Stop H X L H H L X 1
Auto Refresh H HLLLH X 1
Self Refresh
EntryH LLLLH
X
1
Exit L H HXXX 1
LHHH
Precharge Power
Down Mode
Entry H L HXXX
X
1
LHHH 1
Exit L H HXXX 1
LHHH 1
Active Power
Down Mode Entry H L HXXX
X
1
LVVV 1
Exit L H X 1
Note :
1. LDM/UDM states are Don’t Care . Refer to below Write Mask Truth Table.
2. OP Code(Operand Code) consists of A0~A12 and BA0~BA1 used for Mode Register sett ing duing Extended MRS or MRS.
Before entering Mode Register Set mode, all banks must be in a precharge state and MRS command can be issued after tRP
period from Prechagre command.
3. If a Read with Autoprecharge command is detected by memory component in CK(n), then th ere will be no comman d presented
to activated bank until CK(n+BL /2+ t RP).
4. If a Write with Autoprecharge command is detected by memory component in CK(n), then there will be no command presented
to activated bank until CK(n+BL/2+1+ tDPL+tRP). Last Data-In to Prechage delay(tDPL) which is also called Write Recovery Time
(tWR) is needed to guarantee that the last data has been completely written.
5. If A10/AP is High when Precharge command being issued, BA0/BA1 are ignored and all banks are selected to be
precharged.
( H=Logic High Level, L=Logic Low Level, X=Don’t Care, V=Valid Data Input, OP Code=Operand Code, NOP=No Operation )
Rev. 0.4/Feb. 2003 10
HY5DU12422A(L)T
HY5DU12822A(L)T
HY5DU121622A(L)T
WRITE MASK TRUTH TABLE
Function CKEn-1 CKEn /CS, /RAS,
/CAS, /WE DM ADDR A10/
AP BA Note
Data Write H X X L X 1
Data-In Mask H X X H X 1
Note :
1. Write Mask command masks burst write data with reference to LDQS/UDQS(Data Strobes) and it is not related
with read data. In case of x16 data I/O, LDM and UDM control lower byte(DQ0~7) and Upper byte(DQ8~15)
respectively.
Rev. 0.4/Feb. 2003 11
HY5DU12422A(L)T
HY5DU12822A(L)T
HY5DU121622A(L)T
OPERATION COMMAND TRUTH TABLE-I
Current
State /CS /RAS /CAS /WE Address Command Action
IDLE
HXXX X DSEL NOP or power down3
LHHH X NOP NOP or power down3
LHHL X BST ILLEGAL4
L H L H BA, CA, AP READ/READAP ILLEGAL4
L H L L BA, CA, AP WRITE/WRITEAP ILLEGAL4
L L H H BA, RA ACT Row Activ ation
LLHLBA, AP PRE/PALL NOP
LLLH X AREF/SREF A uto Re fresh or Self Refresh5
L L L L OPCODE MRS Mode Register Set
ROW
ACTIVE
HXXX X DSEL NOP
LHHH X NOP NOP
LHHL X BST ILLEGAL4
L H L H BA, CA, AP READ/READAP Begin read : optional AP6
L H L L BA, CA, AP WRITE/WRITEAP Begin write : optional AP6
LLHHBA, RA ACT ILLEGAL4
LLHLBA, AP PRE/PALL Precharge7
LLLH X AREF/SREF ILLEGAL11
LLLLOPCODE MRS ILLEGAL11
READ
H X X X X DSEL Continue burst t o end
L H H H X NOP Continue burst to end
L H H L X BST Terminate burst
L H L H BA, CA, AP READ/READAP Term burst, new read:optional AP8
L H L L BA, CA, AP WRITE/WRITEAP ILLEGAL
LLHHBA, RA ACT ILLEGAL4
L L H L BA, AP PRE/P ALL Term burst, precharge
LLLH X AREF/SREF ILLEGAL11
LLLLOPCODE MRS ILLEGAL11
WRITE
H X X X X DSEL Continue burst t o end
L H H H X NOP Continue burst to end
LHHL X BST ILLEGAL4
L H L H BA, CA, AP READ/READAP Term burst, new read:optional AP8
L H L L BA, CA, AP WRITE/WRITEAP Term burst, new write:optional AP
Rev. 0.4/Feb. 2003 12
HY5DU12422A(L)T
HY5DU12822A(L)T
HY5DU121622A(L)T
OPERATION COMMAND TRUTH TABLE-II
Current
State /CS /RAS /CAS /WE Address Command Action
WRITE
LLHHBA, RA ACT ILLEGAL4
L L H L BA, AP PRE/P ALL Term burst, precharge
LLLH X AREF/SREF ILLEGAL11
LLLLOPCODE MRS ILLEGAL11
READ
WITH
AUTOPRE-
CHARGE
H X X X X DSEL Continue burst t o end
L H H H X NOP Continue burst to end
LHHL X BST ILLEGAL
L H L H BA, CA, AP READ/READAP ILLEGAL10
L H L L BA, CA, AP WRITE/WRITEAP ILLEGAL10
LLHHBA, RA ACT ILLEGAL4,10
LLHLBA, AP PRE/PALL ILLEGAL4,10
LLLH X AREF/SREF ILLEGAL11
LLLLOPCODE MRS ILLEGAL11
WRITE
AUTOPRE-
CHARGE
H X X X X DSEL Continue burst t o end
L H H H X NOP Continue burst to end
LHHL X BST ILLEGAL
L H L H BA, CA, AP READ/READAP ILLEGAL10
L H L L BA, CA, AP WRITE/WRITEAP ILLEGAL10
LLHHBA, RA ACT ILLEGAL4,10
LLHLBA, AP PRE/PALL ILLEGAL4,10
LLLH X AREF/SREF ILLEGAL11
LLLLOPCODE MRS ILLEGAL11
PRE-
CHARGE
H X X X X DSEL NOP-Enter IDLE after tRP
L H H H X NOP NOP-Enter IDLE after tRP
LHHL X BST ILLEGAL4
L H L H BA, CA, AP READ/READAP ILLEGAL4,10
L H L L BA, CA, AP WRITE/WRITEAP ILLEGAL4,10
LLHHBA, RA ACT ILLEGAL4,10
L L H L BA, AP PRE/PALL NOP-Enter IDLE after tRP
LLLH X AREF/SREF ILLEGAL11
LLLLOPCODE MRS ILLEGAL11
Rev. 0.4/Feb. 2003 13
HY5DU12422A(L)T
HY5DU12822A(L)T
HY5DU121622A(L)T
OPERATION COMMAND TRUTH TABLE-III
Current
State /CS /RAS /CAS /WE Address Command Action
ROW
ACTIVATING
H X X X X DSEL NOP - Enter ROW ACT after tRCD
L H H H X NOP NOP - Enter ROW ACT after tRCD
LHHL X BST ILLEGAL4
L H L H BA, CA, AP READ/READAP ILLEGAL4,10
L H L L BA, CA, AP WRITE/WRITEAP ILLEGAL4,10
LLHHBA, RA ACT ILLEGAL4,9,10
LLHLBA, AP PRE/PALL ILLEGAL4,10
LLLH X AREF/SREF ILLEGAL11
LLLLOPCODE MRS ILLEGAL11
WRITE
RECOVERING
H X X X X DSEL NOP - Enter ROW ACT after tWR
L H H H X NOP NOP - Enter ROW ACT after tWR
LHHL X BST ILLEGAL4
L H L H BA, CA, AP READ/READAP ILLEGAL
L H L L BA, CA, AP WRITE/WRITEAP ILLEGAL
LLHHBA, RA ACT ILLEGAL4,10
LLHLBA, AP PRE/PALL ILLEGAL4,11
LLLH X AREF/SREF ILLEGAL11
LLLLOPCODE MRS ILLEGAL11
WRITE
RECOVERING
WITH
AUTOPRE-
CHARGE
H X X X X DSEL NOP - Enter precharge after tDPL
L H H H X NOP NOP - Enter precharge after tDPL
LHHL X BST ILLEGAL4
L H L H BA, CA, AP READ/READAP ILLEGAL4,8,10
L H L L BA, CA, AP WRITE/WRITEAP ILLEGAL4,10
LLHHBA, RA ACT ILLEGAL4,10
LLHLBA, AP PRE/PALL ILLEGAL4,11
LLLH X AREF/SREF ILLEGAL11
LLLLOPCODE MRS ILLEGAL11
REFRESHING
H X X X X DSEL NOP - Enter IDLE after tRC
L H H H X NOP NOP - Enter IDLE after tRC
LHHL X BST ILLEGAL11
L H L H BA, CA, AP READ/READAP ILLEGAL11
Rev. 0.4/Feb. 2003 14
HY5DU12422A(L)T
HY5DU12822A(L)T
HY5DU121622A(L)T
OPERATION COMMAND TRUTH TABLE-IV
Note :
1. H - Logic High Level, L - Logic Low Level, X - Don’t Care, V - Valid Data Input,
BA - Bank Address, AP - AutoPrecharge Address, CA - Column Address, RA - Row Address, NOP - NO Operation.
2. All entries assum e that CKE was active(high level) during the preceding clock cycle.
3. If both banks are idle and CKE is inactive(low level), the n in power down mode.
4. Illegal to bank in specified state. Funct io n ma y be leg al in the bank indicated by Bank Address(BA) depending on the state of
that bank.
5. If both banks are idle and CKE is inactive(low level), the n self refresh mode.
6. Illegal if tRCD is not met.
7. Illegal if tRAS is not met.
8. Must satisfy bus contention, bus turn around, and/or write recovery requirements.
9. Illegal if tRRD is not met.
10. Illegal for single bank, but legal for other banks in multi-bank devices.
11. Illegal for all banks.
Current
State /CS /RAS /CAS /WE Address Command Action
WRITE
L H L L BA, CA, AP WRITE/WRITEAP ILLEGAL11
LLHHBA, RA ACT ILLEGAL11
LLHLBA, AP PRE/PALL ILLEGAL11
LLLH X AREF/SREF ILLEGAL11
LLLLOPCODE MRS ILLEGAL11
MODE
REGISTER
ACCESSING
H X X X X DSEL NOP - Enter IDLE after tMRD
L H H H X N OP NOP - Enter IDLE after tMRD
LHHL X BST ILLEGAL11
L H L H BA, CA, AP READ/READAP ILLEGAL11
L H L L BA, CA, AP WRITE/WRITEAP ILLEGAL11
LLHHBA, RA ACT ILLEGAL11
LLHLBA, AP PRE/PALL ILLEGAL11
LLLH X AREF/SREF ILLEGAL11
LLLLOPCODE MRS ILLEGAL11
Rev. 0.4/Feb. 2003 15
HY5DU12422A(L)T
HY5DU12822A(L)T
HY5DU121622A(L)T
CKE FUNCTION TRUTH TABLE
Note :
When CKE=L, all DQ and DQS must be in Hi-Z state.
1. CKE and /CS must be kept high for a minimum of 200 stable input clocks before issuing any command.
2. All command can be stored after 2 clocks from low to high transition of CKE.
3. Illegal if CK is suspended or stopped during the power down mode.
4. Self refresh can be entered only from the all banks idle state.
5. Disabling CK may cause malfunction of any bank which is in active state.
Current
State CKEn-
1CKEn /CS /RAS /CAS /WE /ADD Action
SELF
REFRESH1
HXXXXXX INVALID
L H H X X X X Exi t s e lf refresh, enter id le after tSREX
L H L H H H X Exit s e lf refresh, enter idle after tSREX
LHLHHLX ILLEGAL
LHLHLXX ILLEGAL
LHLLXXX ILLEGAL
L LXXXXX NOP, continue self refresh
POWER
DOWN2
HXXXXXX INVALID
L H H X X X X Exit power down, enter idle
L H L H H H X Exit power down, enter idle
LHLHHLX ILLEGAL
LHLHLXX ILLEGAL
LHLLXXX ILLEGAL
L L X X X X X NOP, continue power down mode
ALL BANKS
IDLE4
H H X X X X X See operation command truth table
HL LLLHX Enter self refresh
H L H X X X X Exit power down
H L L H H H X Exit power down
HLLHHLX ILLEGAL
HLLHLXX ILLEGAL
HLLLHXX ILLEGAL
HLLLLLX ILLEGAL
L LXXXXX NOP
ANY STATE
OTHER
THAN
ABOVE
H H X X X X X See operation command truth table
HLXXXXX ILLEGAL5
LHXXXXX INVALID
L LXXXXX INVALID
Rev. 0.4/Feb. 2003 16
HY5DU12422A(L)T
HY5DU12822A(L)T
HY5DU121622A(L)T
SIMPLIFIED STATE DIAGRAM
MRS SREF
SREX
PDEN
PDEX
ACT
AREF
PDEX
PDEN
BST
READWRITE
WRITE
WRITEAP
WRITEAP
READ
READAP READAP
PRE(PALL)
PRE(PALL)
PRE(PALL)
Command Input
Automatic Sequence
IDLE
AUTO
REFRESH
PRE-
CHARGE
POWER-UP
POWER APPLIED
MODE
REGISTER
SET
POWER
DOWN
WRITE
WITH
AUTOPRE-
CHARGE
POWER
DOWN
WRITE
READ
WITH
AUTOPRE-
CHARGE
BANK
ACTIVE
READ
SELF
REFRESH
Rev. 0.4/Feb. 2003 17
HY5DU12422A(L)T
HY5DU12822A(L)T
HY5DU121622A(L)T
POWER-UP SEQUENCE AND DEVICE INITIALIZATION
DDR SDRAMs must be powered up and initialized in a predefined manner. Operational procedures other than those
specified may result in undefined operation. Power must first be applied to VDD, then to VDDQ, and finally to VREF
(and to the system VTT). VTT must be applied a fter VDDQ to a void dev ice latch-up , which m ay caus e permanent d am-
age to the device. VREF can be applied anytime after VDDQ, but is expected to be nominally coincident with VTT.
Except for CKE, inputs are not recognized as v alid until after VREF is applied. CKE is an SSTL_2 input, but will detect an
LVCMOS LOW level after VDD is applied. Maintaining an LVCMOS LOW level on CKE during power-up is required to
guarantee that the DQ and DQS outputs will be in the High- Z state, where they will remain until driven in normal oper-
ation (by a read access). After all power supply and reference voltages are stable, and the clock is stable, the DDR
SDRAM requires a 200us delay prior to applying an executable command.
Once the 200us delay has been satisfied, a DESELECT or NOP command should be applied, and CKE should be
brought HIGH. Following the NOP command, a PRECHARGE ALL command should be applied. Next a EXTENDED
MODE REGISTER SET command should be issued for the Extended Mode Register, to enable the DLL, then a MODE
REGISTER SET command should be issued for the Mode Register, to reset the DLL, and to program the operating
parameters. After the DLL re set, tXSRD(DLL locking time) should be sa tisfied for read command. After the Mode Reg-
ister set command, a PRECHARGE ALL command should be applied, placing the device in the all banks idle state.
Once in the idle state, two AUTO REFRESH cycles must be performed. Additionally, a MODE REGISTER SET command
for the Mode Register, with the reset DLL bit low (i.e. to program operating parameters without resetting the DLL)
must be performed. Following these cycles, the DDR SDRAM is ready for no rmal operation.
1. Apply power - VDD, VDDQ , VTT, VREF in the following power up sequencing and attempt to maintain CKE at L VC-
MOS low state. (All the other input pins may be undefined.)
VDD and VDDQ are driven from a single power converter output.
VTT is limited to 1.44V (reflecting VDDQ(max)/2 + 50mV VREF variation + 40mV VTT variation.
VREF tracks VDDQ/2.
A minimum resistance of 42 Ohms (22 ohm se ries r esistor + 22 ohm parallel resistor - 5% toler ance) limits the
input current from the VTT supply into any pin.
If the above criteria cannot be met by the system design, then the following sequencing and voltage relation-
ship must be adhered to during power up.
2. Start clock and maintain stable clock for a minimum of 200usec.
3. After stable power and clock, apply NOP condition and take CKE high.
4. Issue Extended Mode Register Set (EMRS) to enable DLL.
5. Issue Mode Register Set (MRS) to reset DLL and set device to idle state with bit A8=high. (An additional 200
cycles(tXSRD) of clock are required for locking DLL)
6. Issue Precharge commands for all banks of the device.
Voltage description Sequencing Voltage relationship to avoid latch-up
VDDQ After or wi th VDD < VDD + 0.3V
VTT After or with VDDQ < VDDQ + 0.3V
VREF After or with VDDQ < VDDQ + 0.3V
Rev. 0.4/Feb. 2003 18
HY5DU12422A(L)T
HY5DU12822A(L)T
HY5DU121622A(L)T
7. Issue 2 or more Au to Refresh commands.
8. Issue a Mode Register Set command to initialize the mode register with bit A8 = Low
Power-Up Sequence
CODECODE CODE CODECODE
CODECODE CODE CODECODE
CODE CODECODECODECODE
NOP PRE MRSEMRS PRENOP MRSAREF ACT RD
VDD
VDDQ
VTT
VREF
/CLK
CLK
CKE
CMD
DM
ADDR
A10
BA0, BA1
DQS
DQ'S
LVCMOS Low Lev el
tIS tIH
tVTD
T=200usec tRP tMRD tRP tRFC tMRD
tXSRD*
READ
Non-Read
Command
Power UP
VDD and CK stable Precharge All EMRS Set MRS Set
Reset DLL
(with A8=H)
Precharge All 2 or more
Auto Refresh
MRS Set
(wit h A 8=L)
* 200 cycle(tXSRD) of CK are required (for DLL locking) before Read Command
tMRD
Rev. 0.4/Feb. 2003 19
HY5DU12422A(L)T
HY5DU12822A(L)T
HY5DU121622A(L)T
MODE REGISTER SET (MRS)
The mode register is used to store the various operating modes such as /CAS latency, addressing mode, burst length,
burst type, test mode, DLL reset. The mode register is programed via MRS command. This command is issued by the
low signals of /RAS, /CAS, /CS, /WE and BA0. This command can be issued only when all banks are in idle state and
CKE must be high at least one cycle before the Mode Re gister Set Comm and can be issued. Two cycles are required to
write the data in mode register. During the MRS cycle, any command cannot be issued. Once mode register field is
determined, the information will be held until resetted by another MRS command.
BA1 BA0 A12 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0
0 0 Operating Mode CAS Latency BT Burst Length
A2 A1 A0 Burst Length
Sequential Interleave
0 0 0 Reserved Reserved
001 2 2
010 4 4
011 8 8
1 0 0 Reserved Reserved
1 0 1 Reserved Reserved
1 1 0 Reserved Reserved
1 1 1 Reserved Reserved
A3 Burst Type
0 Sequential
1Interleave
A6 A5 A4 CAS Latency
0 0 0 Reserved
0 0 1 Reserved
010 2
011 3
1 0 0 Reserved
101 1.5
110 2.5
1 1 1 Reserved
BA0 MRS Type
0MRS
1EMRS
A12~A9 A8 A7 A6~A0 Operating Mode
0 0 0 Valid Normal Operation
0 1 0 Valid Normal Operation/ Reset DLL
001VS Vendor specific Test Mode
--- All other states reserved
Rev. 0.4/Feb. 2003 20
HY5DU12422A(L)T
HY5DU12822A(L)T
HY5DU121622A(L)T
BURST DEFINITION
BURST LENGTH & TYPE
Read and write accesses to th e DD R SDRA M are bu rst orie nted, wi th the burst length being programmable. The burst
length determines the maximum number of column locations that can be accessed for a given Read or Write com-
mand. Burst lengths of 2, 4 or 8 locations are available for both the sequential and the interleaved burst types.
Reserved states should not be used, as unknown operation or incompatibility with future versions may result.
When a Read or Write command is issued, a block of columns equal to the burst length is effectively selected. All
accesses for that burst take place within this block, meaning that the burst wraps within the block if a boundary is
reached. The block is uniquely selected by A1-Ai when the burst length is set to two, by A2 -Ai when the burst length
is set to four and by A3 -Ai when the burst length is set to eight (where Ai is the most significant column address bit
for a gi ven configuration). The remaining (least significant) address bit(s) is (are) used to select the starting location
within the block. The programmed burst length applies to both Read and Write bursts.
Accesses within a given burst may be programmed to be either sequential or interleaved; this is referred to as the
burst type and is selected via bit A3. The ordering of accesses within a burst is determined by the burst length, the
burst type and the starting column address, as shown in Burst Definitionon Table
Burst Length Starting Address (A2,A1,A0) Sequential Interleave
2XX0 0, 1 0, 1
XX1 1, 0 1, 0
4
X00 0, 1, 2, 3 0, 1, 2, 3
X01 1, 2, 3, 0 1, 0, 3, 2
X10 2, 3, 0, 1 2, 3, 0, 1
X11 3, 0, 1, 2 3, 2, 1, 0
8
000 0, 1, 2, 3, 4, 5, 6, 7 0, 1, 2, 3, 4, 5, 6, 7
001 1, 2, 3, 4, 5, 6, 7, 0 1, 0, 3, 2, 5, 4, 7, 6
010 2, 3, 4, 5, 6, 7, 0, 1 2, 3, 0, 1, 6, 7, 4, 5
011 3, 4, 5, 6, 7, 0, 1, 2 3, 2, 1, 0, 7, 6, 5, 4
100 4, 5, 6, 7, 0, 1, 2, 3 4, 5, 6, 7, 0, 1, 2, 3
101 5, 6, 7, 0, 1, 2, 3, 4 5, 4, 7, 6, 1, 0, 3, 2
110 6, 7, 0, 1, 2, 3, 4, 5 6, 7, 4, 5, 2, 3, 0, 1
111 0, 1, 2, 3, 4, 5, 6, 7 7, 6, 5, 4, 3, 2, 1, 0
Rev. 0.4/Feb. 2003 21
HY5DU12422A(L)T
HY5DU12822A(L)T
HY5DU121622A(L)T
CAS LATENCY
The Read latency or CAS latency is the delay in clock cycles between the registration of a Read command and the
availability of the first burst of output data. The latency can be programmed 2 or 2.5 clocks.
If a Read comma nd is registered at clock ed ge n, and the latency is m clocks, the data is av aila ble nominally coinciden t
with clock edge n + m.
Reserved states should not be used as unknown operation or incompatibility with future versions may result.
DLL RESET
The DLL must be enabled f or normal oper ation. DLL enable is requ ired during pow er up init ializat ion, an d upon ret urn-
ing to normal operation after having disabled the DLL fo r the purpose of debug or evaluation. The DLL is automatically
disabled when entering self refresh operation and is automatically re-enabled upon exit of self refresh operation. Any
time the DLL is enabled, 200 clock cycles must occur to allow time for the internal clock to lock to the externally
applied clock before an any command can be issued.
OUTPUT DRIVER IMPEDANCE CONTROL
The normal drive strength for all outputs is specified to be SSTL_2, Class II. Hynix also supports a half strength driver
option, intended for lighter load and/or point-to-point environments. Selection of the half strength driver option will
reduce the output drive strength by 50% of that of the full strength driver. I-V curves for both the full strength driver
and the half strength driver are included in this document.
Rev. 0.4/Feb. 2003 22
HY5DU12422A(L)T
HY5DU12822A(L)T
HY5DU121622A(L)T
EXTENDED MODE REGISTER SET (EMRS)
The Extended Mode Register controls functions beyond those controlled by the Mode Register; these additional func-
tions include DLL enable/disable, output driver strength se lection(optional). These f unctions are contr olled via the bits
shown below. The Extended Mode Register is progr amme d via th e M ode Register Set command ( BA0=1 and BA1=0)
and will retain the stored information until it is programmed again or the device loses power.
The Extended Mode Register mus t be loaded when all banks are idle and no bursts are in progress, and the contro ller
must wait the specified time before initiating any subsequent operation. Violating either of these requirements will
result in unspecified operation.
BA1 BA0 A12 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0
0 1 Operating Mode 0* DS DLL
A0 DLL enable
0Enable
1Diable
BA0 MRS Type
0MRS
1EMRS
A1 Output Driver
Impedance Control
0 Full Strength Dri ver
1 Half Strength Driver
* This part do not support/QFC function, A2 must be programmed to Zero.
An~A3 A2~A0 Operating Mode
0Valid Noraml Operation
__
All other states reserved
Rev. 0.4/Feb. 2003 23
HY5DU12422A(L)T
HY5DU12822A(L)T
HY5DU121622A(L)T
ABSOLUTE MAXIMUM RATINGS
Note : Operation at above absolute maximum rating can adversely affect device reliability
DC OPERATING CONDITIONS (TA=0 to 70 oC, Voltage referenced to VSS = 0V)
1. VDDQ must not exceed the level of VDD.
2. VIL (min) is acceptable -1.5V AC pulse width with < 5ns of du ration.
3. VREF is expected to be equal to 0.5*VDDQ of the transmitting device, and to track variations in the dc level of the
same. Peak to peak noise on VREF may not exceed +/- 2% of the dc value.
4. VID is the magnitude of the difference between the input level on CK and the input level on /CK.
5. The ratio of the pullup current to the pulldown current is specified for the same temperature and voltage, over the
entire temper ature and voltage range, for device drain to source voltages from 0.25V to 1.0V. For a given output, it
represents the maximum difference between pullup and pulldown drivers due to process variation. The full variation
in the ratio of the maximum to minimum pullup and pulldown current will not exceed 1/7 for device drain to source
voltages from 0.1 to 1.0.
6. VIN=0 to VDD, All other pins are not tested under VIN =0V. 2. DOUT is disabled, VOUT=0 to VDDQ
Parameter Symbol Rating Unit
Ambient Temperature TA0 ~ 70 oC
Storage Temperature TSTG - 55 ~ 125 oC
Voltage on Any Pin relative to VSS VIN, VOUT -0.5 ~ 3.6 V
Voltage on VDD relative to VSS VDD -0.5 ~ 3.6 V
Voltage on VDDQ relative to VSS VDDQ -0.5 ~ 3.6 V
Output Short Circuit Current IOS 50 mA
Power Dissipation PD1W
Soldering Temperature Þ Time TSOLDER 260 Þ 10 oC Þ sec
Parameter Symbol Min Max Unit Note
Power Supply Voltage VDD 2.3 2.7 V
Power Supply Voltage VDDQ 2.3 2.7 V 1
Input High Vo ltage VIH VREF + 0.15 VDDQ + 0.3 V
Input Low Voltage VIL -0.3 VREF - 0.15 V 2
Termination Voltage VTT VREF - 0.04 VREF + 0.04 V
Reference Voltage VREF VDDQ/2 -
50mV VDDQ/2 +
50mV V3
Input Voltage Level, CK and CK inputs VIN(DC) -0.3 VDDQ+0.3 V
Input Differential V o lt age, CK and CK inputs VID(DC) 0.36 VDDQ+0.6 V 4
V-I Ma t chi ng: Pullup to Pulldown Curren t Rati o VI(RATIO) 0.71 1.4 - 5
Input Leakage Current ILI -2 2 uA 6
Output Leakage Current ILO -5 5 uA
Output High Voltage VOH VTT + 0.76 - V IOL = -15.2mA
Output Low Voltage VOL -VTT - 0.76 V IOL = +15.2mA
Rev. 0.4/Feb. 2003 24
HY5DU12422A(L)T
HY5DU12822A(L)T
HY5DU121622A(L)T
DC CHARACTERISTICS II (TA=0 to 70 oC, Voltage referenced to VSS = 0V)
128Mx4
Parameter Symbol Test Condition Speed Unit Note
-J -M -K -H -L
Operating Current IDD0
One bank; Active - Precharge ; tRC=tRC(min);
tCK=tCK(min) ; DQ ,DM and DQS inputs changing twice
per clock cycle; address and control in puts changing
once per clock cycle
140 130 120 120 100 mA
Operating Current IDD1
One bank; Activ e - Read - Precharge;
Burst Length=2; tRC=tRC(min); tCK=tCK(min);
address and control inputs changing once per clock
cycle
180 160 150 150 140 mA
Precharge Power
Down Standby
Current IDD2P All banks idle ; Power down mode; CKE=Low,
tCK=tCK(min) 10 mA
Idle Standby
Current IDD2N Vin>=Vih(min) or Vin=<Vil(max) for DQ, DQS and DM 35 mA
Idle Standby
Current IDD2F
/CS=High, All banks idle; tCK=tCK(min);
CKE=High; address and control inputs changing once
per clock cycle.
VIN=VREF for DQ, DQS and DM
35 mA
Idle Quiet Standby
Current IDD2Q /CS>=Vih(min); All banks idle; CKE>=Vih(min);
Addresses and othe r control inputs st able, Vin=Vref f or
DQ, DQS and DM 25 mA
Active Power
Down
Standby Current IDD3P On e bank active; Power down mode; CKE=Low,
tCK=tCK(min) 12 mA
Active Standby
Current IDD3N
/CS=HIGH; CKE=HIGH; One bank; Active-Precharge;
tRC=tRAS(max); tCK=tCK(min);
DQ, DM and DQS inputs changing twice per clock
cycle; Address and other control inputs changing once
per clock cycle
45 40 mA
Operating Current IDD4R B urst=2; Reads; Continuous burst; One bank acti ve;
Address and control inputs changing once per clock
cycle; tCK=tCK(min ); IOUT=0mA 240 200 200 200 170
mA
Operating Current IDD4W
Burst=2; Writes; Continuous burst; One bank active;
Address and control inputs changing once per clock
cycle; tCK=tCK(min); DQ, DM and DQS inputs
changing twice per clock cycle
240 200 200 200 170
Auto Refresh
Current IDD5 tRC=tRFC(min) - 8*tCK f or DDR200 at 100Mhz, 10*tCK
for DDR266A & DDR266B at 133Mhz; distributed
refresh 280 260 260 260 240
Self Refresh
Current IDD6 CKE =< 0.2V; External clock on;
tCK=tCK(min) Normal 5mA
Low Power 2.5 mA
Operating Current
- Fou r Bank
Operation IDD7 Four bank interleaving with BL=4, Refer to the
following page for detailed test condition 460 380 380 380 300 mA
Random Read
Current IDD7A
4banks active read with activate every 20ns, AP(Auto
Precharge) read every 20ns, BL=4, tRCD=3, IOUT=0
mA, 100% DQ, DM and DQS inputs changing twice per
clock cycle; 100% addresses changing once per clock
cycle
460 380 380 380 300 mA
Rev. 0.4/Feb. 2003 25
HY5DU12422A(L)T
HY5DU12822A(L)T
HY5DU121622A(L)T
DC CHARACTERISTICS II (TA=0 to 70 oC, Voltage referenced to VSS = 0V)
64Mx8
Parameter Symbol Test Condition Speed Unit Note
-J -M -K -H -L
Operating Current IDD0
One bank; Active - Precharge ; tRC=tRC(min);
tCK=tCK(min) ; DQ,DM and DQS inputs changing
twice per clock cycle; address and control inputs
changing once per clock cycle
140 130 120 120 100 mA
Operating Current IDD1
One bank; Active - Read - Precharge;
Burst Length=2; tRC=tRC(min); tCK=tCK(min);
address and control inputs changing once per clock
cycle
180 160 150 150 140 mA
Precharge Power
Down Standby
Current IDD2P All banks idle ; Power down mode; CKE= Low,
tCK=tCK(min) 10 mA
Idle Standby
Current IDD2N Vin>=Vih(min) or Vin=<Vil(max) for DQ, DQS and
DM 35 mA
Idle Standby
Current IDD2F
/CS=High, All banks idle; tCK=tCK(min);
CKE=High; address and control inputs changing onc e
per clock cycle.
VIN=VREF for DQ, DQS and DM
35 mA
Idle Quiet Standby
Current IDD2Q /CS>=Vih(min); All banks idle; CKE>=Vih(min);
Addresses and other control inputs stable, Vin=Vref
for DQ, DQS and DM 25 mA
Active Power
Down
Standby Current IDD3P On e bank active; Power down mode; CKE=Low,
tCK=tCK(min) 12 mA
Active Standby
Current IDD3N
/CS=HIGH; CKE=HIGH; One bank; Active-Precharge;
tRC=tRAS(max); tCK=tCK(min);
DQ, DM and DQS inputs ch anging twice per clock
cycle; Address and other control inputs changing
once per clock cycle
45 40 mA
Operating Current IDD4R Burst=2; Reads; Continuous burs t; One bank active;
Address and control inputs changing once per clock
cycle; tCK=tCK(min); IOUT=0mA 250 210 210 210 180
mA
Operating Current IDD4W
Burst=2; Writes; Continuous burst; One bank active;
Address and control inputs changing once per clock
cycle; tCK=tCK(min); DQ, DM and DQS inputs
changing twice per clock cycle
250 210 210 210 180
Auto Refresh
Current IDD5 tRC=tRFC(min) - 8*tCK for DDR200 at 100Mhz,
10*tCK for DDR266A & DDR266B at 133Mhz;
distributed refresh 280 260 260 260 240
Self Refresh
Current IDD6 CKE =< 0.2V; External clock on;
tCK=tCK(min) Normal 5mA
Low Power 2.5 mA
Operating Current
- Fou r Bank
Operation IDD7 Four bank interleaving with BL=4, Refer to the
following page for detailed test condition 460 380 380 380 300 mA
Random Read
Current IDD7A
4banks active read with activ ate ev er y 20n s, AP(Au to
Precharge) read every 20ns, BL=4, tRCD=3, IOUT=0
mA, 100% DQ, DM and DQS inputs changing twice
per clock cycle; 100% addresses changing once per
clock cycle
460 380 380 380 300 mA
Rev. 0.4/Feb. 2003 26
HY5DU12422A(L)T
HY5DU12822A(L)T
HY5DU121622A(L)T
DC CHARACTERISTICS II (TA=0 to 70 oC, Voltage referenced to VSS = 0V)
32Mx16
Parameter Symbol Test Condition Speed Unit Note
-J -M -K -H -L
Operating
Current IDD0
One bank; Active - Precharge ; tRC=tRC(min);
tCK=tCK(min) ; DQ,DM and DQS inputs changing
twice per clock cycle; address and contro l inputs
changing once per clock cycle
140 130 120 120 100 mA
Operating
Current IDD1
One bank; Active - Read - Precharge;
Burst Length = 2; tRC=tRC(min); tCK=tCK(min);
address and control inputs changing once per clock
cycle
180 160 150 150 140 mA
Precharge Power
Down Standby
Current IDD2P All banks idle; Power down mode; CKE= Low,
tCK=tCK(min) 10 mA
Idle Standby
Current IDD2N Vin>=Vih(min) or Vin=<Vil(max) for DQ, DQS and
DM 35 mA
Idle Standby
Current IDD2F
/CS=High, All banks idle; tCK=tCK(min);
CKE=High; address and control inpu ts chan ging o nce
per clock cycle.
VIN=VREF for DQ, DQS and DM
35 mA
Idle Quiet
Standby Current IDD2Q /CS>=Vih(min); All banks idle; CKE>=Vih(min);
Addresses and other control inputs stable, Vin=Vref
for DQ, DQS and DM 25 mA
Active Power
Down
Standby Current IDD3P One bank active; Power down mode; CKE=Low,
tCK=tCK(min) 12 mA
Active Standby
Current IDD3N
/CS=HIGH; CKE=HIGH; One bank; Active-Precharge;
tRC=tRAS(max); tCK=tCK(min) ;
DQ, DM and DQS inputs changing twice per clock
cycle; Address and other control inp uts changing
once per clock cy cle
45 40 mA
Operating
Current IDD4R Burst=2; Reads; Continuous burst; One bank active;
Address and control input s changing onc e per clock
cycle; tCK=tCK(min); IOUT=0mA 250 210 210 210 180
mA
Operating
Current IDD4W
Burst=2; Writes; Continuous burst; On e bank ac tive;
Address and control input s changing onc e per clock
cycle; tCK=tCK(min); DQ, DM and DQS inputs
changing twice per clock cycle
280 250 250 250 200
Auto Refresh
Current IDD5 tRC=tRFC(min) - 8*tCK for DDR200 at 100Mhz,
10*tCK for DDR266A & DDR266B at 133Mhz;
distributed refresh 280 260 260 260 240
Self Refresh
Current IDD6 CKE =< 0.2V; External clock on;
tCK=tCK(min) Normal 5mA
Low Power 2.5 mA
Operating
Current - Four
Bank Operation IDD7 Four bank interleaving with BL=4, Refer to the
following page for detailed test condition 460 380 380 380 300 mA
Random Read
Current IDD7A
4banks active read with acti vate every 20ns, AP(Auto
Precharge) read every 20ns, BL=4 , tRCD=3, IOUT =0
mA, 100% DQ, DM and DQS inputs changing twice
per clock cycle; 100% addresses changing once per
clock cycle
460 380 380 380 300 mA
Rev. 0.4/Feb. 2003 27
HY5DU12422A(L)T
HY5DU12822A(L)T
HY5DU121622A(L)T
DETAILED TEST CONDITIONS FOR DDR SDRAM IDD1 & IDD7
IDD1 : Operating current: One bank operation
1. Typical Case : VDD = 2.5V, T=25 oC
2. Worst Case : VDD = 2.7V, T= 0 oC
3. Only one bank is accessed with tRC(min), Burst Mode, Address and Control inputs on NOP edge are
changing once per clock cycle. lout = 0mA
4. Timing patterns
- DDR266B(133Mhz, CL=2.5) : tCK = 7.5ns, CL=2.5, BL=4, tRCD = 3*tCK, tRC = 9*tCK, tRAS = 5*tCK
Read : A0 N N R0 N P0 N N N A0 N - repeat the same timing with random address changing
50% of data changing at every burst
- DDR266A (133Mhz, CL=2) : tCK = 7.5ns, CL=2, BL=4, tRCD = 3*tCK, tRC = 9*tCK, tRAS = 5*tCK
Read : A0 N N R0 N P0 N N N A0 N - repeat the same timing with random address changing
50% of data changing at every burst
- DDR333(166Mhz, CL=2.5) : tCK = 6ns, CL=2, BL=4, tRCD = 3*tCK, tRC = 10*tCK, tRAS = 7*tCK
Read : A0 N N R0 N N N P0 N N A0 N - repeat the same timing with random address changing
50% of data changing at every burst
Legend : A=Activate, R=Read, W=Write, P=Precharge, N=NOP
IDD7 : Operating current: Four bank operation
1. Typical Case : VDD = 2.5V, T=25 oC
2. Worst Case : VDD = 2.7V, T= 0 oC
3. Four banks are being interleaved with tRC(min), Burst Mode, Address and Control inputs on NOP edge are not
changing. lout = 0mA
4. Timing patterns
- DDR266B(133Mhz, CL=2.5) : tCK = 7.5ns, CL=2.5, BL=4, tRRD = 2*tCK, tRCD = 3*tCK Read with autopr echarg e
Read : A0 N A1 R0 A2 R1 A3 R2 N R3 A0 N A1 R0 - repeat the same timing with random address changing
50% of data changing at every burst
- DDR266A (133Mhz, CL=2) : tCK = 7.5ns, CL2=2, BL=4, tRRD = 2*tCK, tRCD = 3*tCK
Read : A0 N A1 R0 A2 R1 A3 R2 N R3 A0 N A1 R0 - repeat the same timing with random address changing
50% of data changing at every burst
- DDR333(166Mhz, CL=2.5) : tCK = 6ns, CL=2.5, BL=4, tRRD = 2*tCK, tRCD = 3*tCK, Read with autoprecharge
Read : A0 N A1 R0 A2 R1 A3 R2 N R3 A0 N A1 R0 - repeat the same timing with random address changing
50% of data changing at every burst
Legend : A=Activate, R=Read, W=Write, P=Precharge, N=NOP
Rev. 0.4/Feb. 2003 28
HY5DU12422A(L)T
HY5DU12822A(L)T
HY5DU121622A(L)T
AC OPERATING CONDITIONS (TA= 0 to 70 oC, Voltage referenced to VSS = 0V)
Note :
1. VID is the magnitude of the difference between the input level on CK and the input on /CK.
2. The value of VIX is expected to equal 0.5*V DDQ of the transmitting device and must track variations in the DC level of the same.
AC OPERATING TEST CONDITIONS (TA=0 to 70oC, Voltage referenced to VSS = 0V)
Parameter Symbol Min Max Unit Note
Input High (Logic 1) Voltage, DQ, DQS and DM signals VIH(AC) VREF + 0.31 V
Input Low (Logic 0) Voltage, DQ, DQS and DM signals VIL(AC) VREF - 0.31 V
Input Differential Voltage, CK and /CK inputs VID(AC) 0.7 VDDQ + 0.6 V 1
Input Crossin g Point Voltage, CK and /CK inputs VIX(AC) 0.5*VDDQ-0.2 0.5*VDDQ+0.2 V 2
Parameter Value Unit
Reference Voltage VDDQ x 0.5 V
Termination Voltage VDDQ x 0.5 V
AC Input High Level Voltage (VIH, min ) VREF + 0.31 V
AC Input Low Level Vo ltage (VIL, max) VREF - 0.31 V
Input Timing Measurement Reference Level Voltage VREF V
Output Timing Meas urement Refe r e n ce Level Voltage VTT V
Input Signal maximum peak swing 1.5 V
Input minimum Signal Slew Rate 1 V/ns
Termination Resistor (RT)50W
Series Resistor (RS)25W
Output Load Capacitance for Access Time Measurement (CL)30 pF
Rev. 0.4/Feb. 2003 29
HY5DU12422A(L)T
HY5DU12822A(L)T
HY5DU121622A(L)T
AC Overshoot/Undershoot Specification for Address and Control Pins
This specification is intended for devices with no clamp protection and is guaranteed by design
Overshoot/Undershoot Specification for Data, Strobe, and Mask Pins
Parameter Specification
DDR333 DDR200/266
Maximum peak amplitude allowed for overshoot (See Figure 1): 1.5V 1.5V
Maximum peak amplitude allowed for undershoot (See Figure 1): 1.5V 1.5V
The area between the overshoot signal and VDD must be less than or equal to (See Figure 1): 4.5V - ns 4.5V - ns
The area between the undershoot signal and GND mus t be less than or equal to (See Figure 1): 4.5V - ns 4.5V - ns
Parameter Specification
DDR333 DDR200/266
Maximum peak amplitude allowed for overshoot (See Figure 2): 1.2V 1.2V
Maximum peak amplitude allowed for undershoot (See Figure 2): 1.2V 1 .2V
The area between the overshoot signal and VDD must be less than or equal to (See Figure 2): 2.4V - ns 2.4V - ns
The area between the undershoot signal and GND must be less than or equal to (See Figure 2): 2.4V - ns 2.4V - ns
V
DD
0123456
0
+1
+2
+3
+4
+5
-1
-2
-3
Volts
(V)
Time(ns)
Undershoot
Ground
Max. area=4.5V-ns
Overshoot
Max. amplitude=1.5V
Figure 1: Address and Control AC Overshoot and Undershoot Definitio
V
DD
0123456
0
+1
+2
+3
+4
+5
-1
-2
-3
Volts
(V)
Time(ns)
Undershoot
Ground
Max. area=2.4V-ns
Overshoot
Max. amplitude=1.2V
Figure 2: DQ/DM/DQS AC Overshoot and Undershoot Definition
Rev. 0.4/Feb. 2003 30
HY5DU12422A(L)T
HY5DU12822A(L)T
HY5DU121622A(L)T
AC CHARACTERISTICS I (AC operating conditions unless otherwise noted)
Parameter Symbol DDR333 DDR266 UNIT NOTE
Min Max Min Max
Row Cycle Time tRC 60 - 60 - ns
Auto Refresh Row Cycle Time tRFC 72 - 75 - ns
Row Active Time tRAS 42 70K 45 120K ns
Active to Read with Aut o Precharge
Delay tRAP tRCD or
tRPmin -tRCD or
tRPmin -ns16
Row Address to Column Address Delay tRCD 18 - 15 - ns
Row Active to Row Active Delay tRRD 12 - 15 - ns
Column Address to Column Address
Delay tCCD 1 - 1 - CK
Row Precharge Time tRP 18 - 15 - ns
Write Rec overy Time tWR 15 - 15 - ns
Internal Write to Read Command Delay tWTR 1 - 1 - CK
Auto Precharge Write Recovery +
Precharge Time tDAL (tWR/tCK)
+
(tRP/tCK) -(tWR/tCK)
+
(tRP/tCK) -CK15
System Clock Cycle
Time CL = 2.5 tCK 6127.512ns
CL = 2 7.5 12 7.5 12 ns
Clock High Level Width tCH 0.45 0.55 0.45 0.55 CK
Clock Low Level Width tCL 0.45 0.55 0.45 0.55 CK
Data-Out edge to Clock edge Skew tAC -0.7 0 .7 -0.7 5 0.7 5 ns
DQS-Out edge to Clock edge Skew tDQSCK -0.6 0.6 -0.75 0.75 ns
DQS-Out edge to Data-Out edge Skew tDQSQ - 0.45 - 0.5 ns
Data-Out hold time from DQS tQH tHP
-tQHS -tHP
-tQHS -ns1,10
Clock Half Period tHP min
(tCL,tCH) -min
(tCL,tCH) -ns1,9
Data Hold Skew Factor tQHS - 0.55 - 0.75 ns 10
Vali d Data Output Window tDV tQH-tDQSQ tQH-tDQSQ ns
Data-out high-impedance window from
CK,/CK tHZ -0.7 0.7 -0.75 0.75 ns 17
Data-out low - impedance window from
CK, /CK tLZ -0.7 0.7 -0.75 0.75 ns
Input Setup T im e (fast slew rate) tIS 0.75 - 0 .9 - ns 2,3,5,6
Input Hold Time (fast slew rate) tIH 0.75 - 0.9 - ns
Rev. 0.4/Feb. 2003 31
HY5DU12422A(L)T
HY5DU12822A(L)T
HY5DU121622A(L)T
-Continue-
Parameter Symbol DDR333 DDR266 UNIT NOTE
Min Max Min Max
Input Setup Time (slow slew rate) tIS 0.8 - 1.0 - ns 2,4,5,6
Input Hold Time (slow slew rate) tIH 0.8 - 1.0 - ns
Input Pulse Width tIPW 2.2 - 2.2 - ns 6
Write DQS High Level Width tDQSH 0.35 - 0.35 - CK
Write DQS Low Level Width tDQSL 0.35 - 0.35 - CK
Clock to First Rising edge of DQS-In tDQSS 0.75 1.25 0.72 1.28 CK
DQS falling edge to CK setup time tDSS 0.2 0.2 CK
DQS fallin g edge hold time from CK tDSH 0.2 0.2 CK
Data-In Setup Time to DQS-In
(DQ & DM) tDS 0.45 - 0.5 - ns 6,7,11,
12,13
Data-in Hold Time to DQS-In
(DQ & DM) tDH 0.45 - 0.5 - ns
DQ & DM Input Pulse Width tDIPW 1.75 - 1.75 - ns
Read DQS Preamble Time tRPRE 0.9 1.1 0.9 1.1 CK
Read DQS Postamble Time tRPST 0.4 0.6 0.4 0.6 CK
Write DQS Preamble Setup Time tWPRES 0-0-CK
Write DQS Preamble Hold Time tWPREH 0.25 - 0.25 - CK
Write DQS Postamble Time t WPST 0.4 0.6 0.4 0.6 CK
Mode Register Set Delay tMRD 2-2-CK
Exit Self Refresh to Any Execute
Command tXSC 200 - 200 - CK 8
Average Periodic Refresh Interval tREFI -7.8-7.8us
Rev. 0.4/Feb. 2003 32
HY5DU12422A(L)T
HY5DU12822A(L)T
HY5DU121622A(L)T
AC CHARACTERISTICS II (AC operating conditions unless otherwise noted)
Parameter Symbol DDR266A DDR266B DDR200 UNI
TNOTE
Min Max Min Max Min Max
Row Cycle Time tRC 65 - 65 - 70 - ns
Auto Refresh Row Cycle Time tRFC 75 - 75 - 80 - ns
Row Active Time tRAS 45 120K 45 120K 50 120K ns
Active to Read with Auto
Precharge Delay tRAP tRCD or
tRPmin -tRCD or
tRPmin -tRCD or
tRPmin -ns16
Row Address to Column Address
Delay tRCD 20 - 20 - 20 - ns
Row Active to Row Active Delay tRRD 15 - 15 - 15 - ns
Column Address to Column
Address Delay tCCD 1 - 1 - 1 - CK
Row Precharge Time tRP 20 - 20 - 20 - n s
Write Rec overy Time tWR 15 - 15 - 15 - ns
Internal Write to R ead Command
Delay tWTR1-1-1-CK
Auto Precharge Write Recovery +
Precharge Time tDAL (tWR/tCK)
+
(tRP/tCK) -(tWR/tCK)
+
(tRP/tCK) -(tWR/tCK)
+
(tRP/tCK) -CK15
System Clock Cycle
Time CL = 2.5 tCK 7.5 12 7.5 12 8.0 12 ns
CL = 2 7.5 12 10 12 10 12 ns
Clock High Level Width tCH 0.45 0.55 0.45 0.55 0.45 0.55 CK
Clock Low Level Width tCL 0.45 0.55 0.45 0.55 0.45 0.55 CK
Data-Out edge to Clock edge
Skew tAC -0.75 0.75 -0.75 0.75 -0.75 0.75 ns
DQS-Out edge to Clock edge
Skew tDQSCK -0.75 0.75 -0.75 0.75 -0.75 0.75 ns
DQS-Out ed ge to Data-Out edge
Skew tDQSQ - 0.5 - 0.5 - 0.6 ns
Data-Out hold time from DQS tQH tHP
-tQHS -tHP
-tQHS -tHP
-tQHS -ns1,10
Clock Half Period tHP min
(tCL,tCH
)-min
(tCL,tCH
)-min
(tCL,tCH
)-ns1,9
Data Hold Skew Factor tQHS - 0.75 - 0.75 - 0.75 ns 10
Vali d Data Output Window tDV tQH-tDQSQ tQH-tDQSQ tQH-tDQSQ ns
Data-out high -i mpe dan ce
window from CK,/CK tHZ -0.75 0.75 -0.75 0.75 -0.8 0.8 ns 17
Data-out low-impedance window
from CK, /CK tLZ -0.75 0.75 -0.75 0.75 -0.8 0.8 ns 17
Rev. 0.4/Feb. 2003 33
HY5DU12422A(L)T
HY5DU12822A(L)T
HY5DU121622A(L)T
-Continue:
1. This calculation accounts for tDQSQ(max), the pulse wi dth distortion of on-chip circuit and jitter.
2. Data sampled at the rising edges of the clock : A0~A12, BA0~BA1, CKE, /CS, /RAS, /CAS, /WE.
3. For command/address input slew rate >=1.0V/ns
4. For command/address input slew rate >=0.5V/ns and <1.0V/ns
This derating table is used to increase tIS/tIH in case where the input slew-rate is below 0.5V/ns.
Input Setup / Hold Slew-rate Derating Table.
Parameter Symbol DDR266A DDR266B DDR200 UNIT NOTE
Min Max Min Max Min Max
Input Setup Time
(fast slew rate) tIS 0.9 - 0.9 - 1.1 - ns 2,3,5,
6
Input Hold Time
(fast slew rate) tIH 0.9 - 0.9 - 1.1 - ns
Input Setup Time
(slow slew rate) tIS 1.0 - 1.0 - 1.1 - ns 2,4,5,
6
Input Hold Time
(slow slew rate) tIH 1.0 - 1.0 - 1.1 - ns
Input Pulse Width tIPW 2.2 - 2.2 - 2.5 - ns 6
Write DQS High Level Width tDQSH 0.35 - 0.35 - 0.35 - CK
Write DQS Low Level Width tDQSL 0.35 - 0.35 - 0.35 - CK
Clock to First Ris ing edge of
DQS-In tDQSS 0.75 1.25 0.75 1.25 0.75 1.25 CK
DQSfalling edge to CK
setup time tDSS 0.2 0.2 0.2 CK
DQS falling edge hold time from C K tDSH 0.2 0.2 0.2 CK
Data-In Setup Time to DQS-
In (DQ & DM) tDS 0.5 - 0.5 - 0.6 - ns 6,7,
11,12,
13
Data-in Hold Time to DQS-In
(DQ & DM) tDH 0.5 - 0.5 - 0.6 - ns
DQ & DM Input Pulse Width tDIPW 1.75 - 1.75 - 2 - ns
Read DQS Preamble Time tRPRE 0.9 1.1 0.9 1.1 0.9 1.1 CK
Read DQS Postamble Time tRPST 0.4 0.6 0.4 0.6 0.4 0.6 CK
Write DQS Preamble Setup Time tWPRES 0-0-0-CK
Write DQS Preamble Hold Time tWPREH 0.25 - 0.25 - 0.25 - CK
Write DQS Postamble Time tWPST 0.4 0.6 0.4 0.6 0.4 0.6 CK
Mode Register Set Delay tMRD 2-2-2-CK
Exit Self Refr es h to An y
Execute Command tXSC 200 - 200 - 200 - CK 8
Average Periodic Refresh
Interval tREFI -7.8-7.8-7.8us
Input Setup / Hold Slew-rate Delta tIS Delta tIH
V/ns ps ps
0.5 0 0
0.4 +50 0
0.3 +100 0
Rev. 0.4/Feb. 2003 34
HY5DU12422A(L)T
HY5DU12822A(L)T
HY5DU121622A(L)T
5. CK, /CK slew rates are >=1.0V/ns
6. These parameters guarantee device timing, but they are not necessarily tested on each device, and they may be guaranteed
by design or tester correlation.
7. Data latched at both rising and falling edges of Data Strobes(LDQS/UDQS) : DQ, LDM/UDM.
8. Minimum of 2 0 0 cycles of stable input clocks after Self Refresh Exit comm a nd, where CKE is held high, is required to
complete Self Refresh Exit and lock the internal DLL circuit of DDR SDRAM.
9. Min (tCL, tCH) refers to the smaller of the actual clock low time and the actual clock high time as provided to the device
(i.e. this value can be greater than the minimum specification limits for tCL and tCH).
10. tHP = minimum half clock period for any given cycle and is defined by clock high or clock low (tCH, tCL).
tQHS consists of tDQSQmax, the pulse width distortion of on-chip clock circuits, data pin to pin skew and output pattern
effects and p-channel to n-channel va riati on of the output drivers.
11 .This derating table is used to increase tDS/tDH in case where the input slew-rate is below 0.5V/ns.
Input Setup / Hold Slew-rate Derating Table.
12. I/O Setup/Hold Plateau Derating. This derating table is used to increase tDS/tDH in case where the input level is
flat below VR EF +/-310mV for a duration of up to 2ns.
13. I/O Setup/Hold Delta Inverse Slew Rate Derating. This derating table is used to increase tDS/tDH in case where the DQ and
DQS slew ra tes differ. The Delta Inverse Slew Rate is calculated as (1/SlewRate1)-(1/SlewRate2). For example,
if slew rate 1 = 0.5V/ns and Slew Rate2 = 0.4V/n then the Delta Inverse Slew Rate = -0.5ns/V.
14. DQS, DM and DQ input slew rate is speci fied to prevent double clocking of data and preserve setup and hold times.
Signal transitions through the DC region must be monotonic.
15. tDAL = 2 clocks + (tRP / tCK ). For each of the terms above, if not already an integer, round to the next highest integer.
tCK is equal to the actual system clock cycle time.
Example: For DDR266B at CL=2.5 and tCK = 7.5 ns,
tDAL = (15 ns / 7.5 ns) + (20 ns / 7.5 ns) = (2.00) + (2.67)
Round up each non-integer to the next highest integer: = (2) + (3), tDAL = 5 clocks
16. For the parts which do not has internal RAS lockout circuit, Active to Read wit h Auto precharge delay
should be tRAS - BL/2 x tCK.
Input Setup / Hold Slew-rate Delta tDS Delta tDH
V/ns ps ps
0.5 0 0
0.4 +75 +75
0.3 +150 +150
I/O Input Level Delta tDS Delta tDH
mV ps ps
+280 +50 +50
(1/SlewRate1)-(1/SlewRate2) Delta tDS Delta tDH
ns/V ps ps
000
+/-0.25 +50 +50
+/- 0. 5 +100 +100
Rev. 0.4/Feb. 2003 35
HY5DU12422A(L)T
HY5DU12822A(L)T
HY5DU121622A(L)T
CAPACITANCE (TA=25oC, f=100MHz )
Note :
1. VDD = min. to max., VDDQ = 2.3V to 2.7V, VODC = VDDQ/2, VOpeak-to-peak = 0.2V
2. Pins not under test are tied to GND.
3. These values are guaranteed by design and are tested on a sample basis only.
OUTPUT LOAD CIRCUIT
Parameter Pin Symbol Min Max Unit
Input Clock Capacitance CK, /CK CI1 2.0 3.0 pF
Delta Input Clock Capacitance CK, /CK Delta CI1 -0.25pF
Input Capacita n ce All other input-only pins CI1 2.0 3.0 pF
Delta Input Capacit ance All other input-only pins Delta CI2 -0.5pF
Input / Output Capacitanc DQ, DQS, DM CIO 4.0 5.0 pF
Delta Input / Output Capa citance DQ, DQS, DM Delta CIO -0.5pF
VREF
VTT
RT=50
Zo=50
CL=30pF
Output
Rev. 0.4/Feb. 2003 36
HY5DU12422A(L)T
HY5DU12822A(L)T
HY5DU121622A(L)T
PACKAGE INFORMATION
400mil 66pin Thin Small Outline Package
10.26 (0.404)
10.05 (0.396)
11.94 (0.470)
11.79 (0.462)
22.33 (0.879)
22.12 (0.871)
1.194 (0.0470)
0.991 (0.0390)
0.65 (0.0256) BSC 0.35 (0.0138)
0.25 (0.0098)
0.15 (0.0059)
0.05 (0.0020)
BASE PLANE
SEATING PL AN E
0.597 (0.0235)
0.406 (0.0160) 0.210 (0. 0083)
0.120 (0.0047)
0 ~ 5 Deg.
Unit : mm (In ch )