2.5 V to 5.5 V, 400 A, Quad Voltage Output, 8-/10-/12-Bit DACs in 16-Lead TSSOP AD5307/AD5317/AD5327 FEATURES GENERAL DESCRIPTION AD5307: 4 buffered 8-bit DACs in 16-lead TSSOP A version: 1 LSB INL; B version: 0.625 LSB INL AD5317: 4 buffered 10-bit DACs in 16-lead TSSOP A version: 4 LSB INL; B version: 2.5 LSB INL AD5327: 4 buffered 12-bit DACs in 16-lead TSSOP A version: 16 LSB INL; B version: 10 LSB INL Low power operation: 400 A @ 3 V, 500 A @ 5 V 2.5 V to 5.5 V power supply Guaranteed monotonic by design over all codes Power down to 90 nA @ 3 V, 300 nA @ 5 V (LDAC pin) Double-buffered input logic Buffered/unbuffered reference input options Output range: 0 V to VREF or 0 V to 2 VREF Power-on reset to 0 V Simultaneous update of outputs (LDAC pin) Asynchronous clear facility (CLR pin) Low power, SPI(R)-, QSPITM-, MICROWIRETM-, and DSPcompatible 3-wire serial interface SDO daisy-chaining option On-chip rail-to-rail output buffer amplifiers Temperature range of -40C to +105C The AD5307/AD5317/AD53271 are quad 8-,10-,12-bit buffered voltage-output DACs in 16-lead TSSOP that operate from single 2.5 V to 5.5 V supplies and consume 400 A at 3 V. Their onchip output amplifiers allow the outputs to swing rail-to-rail with a slew rate of 0.7 V/s. The AD5307/AD5317/AD5327 utilize versatile 3-wire serial interfaces that operate at clock rates up to 30 MHz; these parts are compatible with standard SPI, QSPI, MICROWIRE, and DSP interface standards. The references for the four DACs are derived from two reference pins (one per DAC pair). These reference inputs can be configured as buffered or unbuffered inputs. Each part incorporates a poweron reset circuit, ensuring that the DAC outputs power up to 0 V and remain there until a valid write to the device takes place. There is also an asynchronous active low CLR pin that clears all DACs to 0 V. The outputs of all DACs can be updated simultaneously using the asynchronous LDAC input. Each part contains a power-down feature that reduces the current consumption of the device to 300 nA @ 5 V (90 nA @ 3 V). The parts can also be used in daisy-chaining applications using the SDO pin. APPLICATIONS Portable battery-powered instruments Digital gain and offset adjustment Programmable voltage and current sources Programmable attenuators Industrial process control All three parts are offered in the same pinout, allowing users to select the amount of resolution appropriate for their application without redesigning their circuit board. FUNCTIONAL BLOCK DIAGRAM VDD VREFAB AD5307/AD5317/AD5327 GAIN-SELECT LOGIC LDAC SCLK INPUT REGISTER DAC REGISTER STRING DAC A BUFFER VOUTA INPUT REGISTER DAC REGISTER STRING DAC B BUFFER VOUTB INPUT REGISTER DAC REGISTER STRING DAC C BUFFER VOUTC INPUT REGISTER DAC REGISTER STRING DAC D BUFFER VOUTD INTERFACE LOGIC SYNC DIN POWER-ON RESET DCEN LDAC CLR POWER-DOWN LOGIC VREFCD PD GND 02067-001 SDO Figure 1. 1 Protected by U.S. Patent No. 5,969,657; other patents pending. Rev. C Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.461.3113 (c)2006 Analog Devices, Inc. All rights reserved. AD5307/AD5317/AD5327 TABLE OF CONTENTS Features .............................................................................................. 1 Input Shift Register .................................................................... 17 Applications....................................................................................... 1 Control Bits ................................................................................. 17 General Description ......................................................................... 1 Low Power Serial Interface ....................................................... 18 Functional Block Diagram .............................................................. 1 Daisy Chaining ........................................................................... 18 Revision History ............................................................................... 2 Double-Buffered Interface ........................................................ 18 Specifications..................................................................................... 3 Load DAC Input (LDAC).......................................................... 18 AC Characteristics........................................................................ 5 Power-Down Mode .................................................................... 18 Timing Characteristics ................................................................ 5 Microprocessor Interfacing....................................................... 19 Absolute Maximum Ratings............................................................ 7 Applications..................................................................................... 20 ESD Caution.................................................................................. 7 Typical Application Circuit....................................................... 20 Pin Configuration and Function Descriptions............................. 8 Driving VDD from the Reference Voltage ................................ 20 Typical Performance Characteristics ............................................. 9 Bipolar Operation....................................................................... 20 Terminology .................................................................................... 13 Opto-Isolated Interface for Process-Control Applications... 21 Transfer Function ........................................................................... 14 Decoding Multiple AD5307/AD5317/AD5327 Devices....... 21 Functional Description .................................................................. 15 AD5307/AD5317/AD5327 as Digitally Programmable Window Detectors ..................................................................... 21 Digital-to-Analog Section ......................................................... 15 Resistor String ............................................................................. 15 DAC Reference Inputs ............................................................... 15 Output Amplifier........................................................................ 16 Power-On Reset .......................................................................... 16 Daisy Chaining ........................................................................... 22 Power Supply Bypassing and Grounding................................ 22 Outline Dimensions ....................................................................... 24 Ordering Guide .......................................................................... 25 Serial Interface ................................................................................ 17 REVISION HISTORY 3/06--Rev. B to Rev. C Changes to Table 3............................................................................ 5 Changes to Ordering Guide .......................................................... 25 10/05--Rev. A to Rev. B Updated Format..................................................................Universal Changes to Bipolar Operation Section ........................................ 21 Changes to Ordering Guide .......................................................... 25 8/03--Rev. 0 to Rev. A Added A Version ................................................................Universal Changes to Features ..........................................................................1 Changes to Specifications.................................................................2 Changes to Absolute Maximum Ratings........................................6 Changes to Ordering Guide .............................................................6 Changes to TPC 21......................................................................... 12 Added Octals section to Table II .................................................. 20 Updated Outline Dimensions....................................................... 21 Rev. C | Page 2 of 28 AD5307/AD5317/AD5327 SPECIFICATIONS VDD = 2.5 V to 5.5 V, VREF = 2 V, RL = 2 k to GND, CL = 200 pF to GND. All specifications TMIN to TMAX, unless otherwise noted. Table 1. Parameter 2 DC PERFORMANCE 3 , 4 AD5307 Resolution Relative Accuracy Differential Nonlinearity Min A Version 1 Typ Max Min B Version Typ Max Unit 8 0.15 0.02 1 0.25 8 0.15 0.02 0.625 0.25 Bits LSB LSB AD5317 Resolution Relative Accuracy Differential Nonlinearity 10 0.5 0.05 4 0.5 10 0.5 0.05 2.5 0.5 Bits LSB LSB AD5327 Resolution Relative Accuracy Differential Nonlinearity 12 2 0.2 16 1 12 2 0.2 10 1 Bits LSB LSB Offset Error 5 60 5 60 mV Gain Error 0.3 1.25 0.3 1.25 % FSR Lower Dead Band 5 10 60 10 60 mV Upper Dead Band 10 60 10 60 mV Offset Error Drift 6 -12 -12 Gain Error Drift -5 -5 -60 200 -60 200 DC Power Supply Rejection Ratio DC Crosstalk DAC REFERENCE INPUTS VREF Input Range 1 0.25 VREF Input Impedance (RDAC) Reference Feedthrough Channel-to-Channel Isolation OUTPUT CHARACTERISTICS Minimum Output Voltage 7 Maximum Output Voltage DC Output Impedance Short-Circuit Current Power-Up Time VDD VDD 1 0.25 >10 ppm of FSR/C ppm of FSR/C dB mV VDD VDD >10 V V M 74 90 74 90 k 37 45 37 45 k -90 -75 -90 -75 dB dB 0.001 0.001 V VDD - 0.001 0.5 25 16 2.5 VDD - 0.001 0.5 25 16 2.5 V mA mA s 5 5 s Rev. C | Page 3 of 28 Conditions/Comments Guaranteed monotonic by design over all codes Guaranteed monotonic by design over all codes Guaranteed monotonic by design over all codes VDD = 4.5 V, gain = 2; see Figure 29 and Figure 30 VDD = 4.5 V, gain = 2; see Figure 29 and Figure 30 See Figure 29, lower dead band exists only if offset error is negative See Figure 30, upper dead band exists only if VREF = VDD and offset plus gain error is positive VDD = 10% RL = 2 k to GND or VDD Buffered reference mode Unbuffered reference mode Buffered reference mode and power-down mode Unbuffered reference mode, 0 V to VREF output range Unbuffered reference mode, 0 V to 2 VREF output range Frequency = 10 kHz Frequency = 10 kHz A measure of the minimum drive capability of the output amplifier A measure of the maximum drive capability of the output amplifier VDD = 5 V VDD = 3 V Coming out of power-down mode, VDD = 5 V Coming out of power-down mode, VDD = 3 V AD5307/AD5317/AD5327 Parameter 2 LOGIC INPUTS Input Current Input Low Voltage, VIL Min A Version 1 Typ Max Min 1 0.8 0.6 0.5 1 0.8 0.6 0.5 Input High Voltage, VIH (Excluding DCEN) 1.7 1.7 Input High Voltage, VIH (DCEN) 2.4 2.4 2.1 2.0 2.1 2.0 Pin Capacitance LOGIC OUTPUT (SDO) VDD = 4.5 V to 5.5 V Output Low Voltage, VOL Output High Voltage, VOH VDD = 2.5 V to 3.6 V Output Low Voltage, VOL Output High Voltage, VOH Floating State Leakage Current Floating State Output Capacitance POWER REQUIREMENTS VDD IDD (Normal Mode) 8 VDD = 4.5 V to 5.5 V VDD = 2.5 V to 3.6 V IDD (Power-Down Mode) VDD = 4.5 V to 5.5 V VDD = 2.5 V to 3.6 V B Version Typ Max 3 0.4 VDD = 3 V 10% VDD = 2.5 V V V ISINK = 2 mA ISOURCE = 2 mA V V ISINK = 2 mA ISOURCE = 2 mA 1 A pF DCEN = GND DCEN = GND 5.5 V 0.4 0.4 0.4 VDD - 0.5 1 3 2.5 3 5.5 VDD = 5 V 10% VDD = 3 V 10% VDD = 2.5 V VDD = 2.5 V to 5.5 V; TTL and 1.8 V CMOS compatible V V pF VDD - 1 VDD - 0.5 mA V V V V Conditions/Comments VDD = 5 V 10% 3 VDD - 1 Unit 2.5 500 400 900 750 500 400 900 750 A A 0.3 0.09 1 1 0.3 0.09 1 1 A A 1 VIH = VDD and VIL = GND All DACs in unbuffered mode; in buffered mode, extra current is typically x mA per DAC, where x = 5 mA + VREF/RDAC VIH = VDD and VIL = GND Temperature range (A, B versions): -40C to +105C; typical at +25C. See the Terminology section. 3 DC specifications tested with the outputs unloaded, unless otherwise noted. 4 Linearity is tested using a reduced code range: AD5307 (Code 8 to Code 255); AD5317 (Code 28 to Code 1023); AD5327 (Code 115 to Code 4095). 5 This corresponds to x codes, where x = deadband voltage/LSB size. 6 Guaranteed by design and characterization; not production tested. 7 For the amplifier output to reach its minimum voltage, offset error must be negative. For the amplifier output to reach its maximum voltage, VREF = VDD and offset plus gain error must be positive. 8 Interface inactive. All DACs active. DAC outputs unloaded. 2 Rev. C | Page 4 of 28 AD5307/AD5317/AD5327 AC CHARACTERISTICS VDD = 2.5 V to 5.5 V, RL = 2 k to GND, CL = 200 pF to GND. All specifications TMIN to TMAX, unless otherwise noted. Table 2. 2, 3 Parameter Output Voltage Settling Time AD5307 AD5317 AD5327 Slew Rate Major-Code Change Glitch Energy Digital Feedthrough SDO Feedthrough Digital Crosstalk Analog Crosstalk DAC-to-DAC Crosstalk Multiplying Bandwidth Total Harmonic Distortion A, B Versions 1 Min Typ Max Unit 6 7 8 0.7 12 0.5 4 0.5 1 3 200 -70 s s s V/s nV-s nV-s nV-s nV-s nV-s nV-s kHz dB 8 9 10 Conditions/Comments VREF = VDD = 5 V 1/4 scale to 3/4 scale change (0x40 to 0xC0) 1/4 scale to 3/4 scale change (0x100 to 0x300) 1/4 scale to 3/4 scale change (0x400 to 0xC00) 1 LSB change around major carry Daisy-chain mode; SDO load is 10 pF VREF = 2 V 0.1 V p-p; unbuffered mode VREF = 2.5 V 0.1 V p-p; frequency = 10 kHz 1 Temperature range (A, B versions): -40C to +105C; typical at +25C. Guaranteed by design and characterization; not production tested. 3 See the Terminology section. 2 TIMING CHARACTERISTICS VDD = 2.5 V to 5.5 V; all specifications TMIN to TMAX, unless otherwise noted. Table 3. Parameter 1, 2 , A, B Versions Limit at TMIN, TMAX Unit Conditions/Comments 33 13 13 13 5 4.5 5 50 20 20 20 0 20 25 5 8 0 ns min ns min ns min ns min ns min ns min ns min ns min ns min ns min ns min ns min ns max ns max ns min ns min ns min SCLK cycle time SCLK high time SCLK low time SYNC to SCLK falling edge set-up time Data set-up time Data hold time SCLK falling edge to SYNC rising edge Minimum SYNC high time LDAC pulse width SCLK falling edge to LDAC rising edge CLR pulse width SCLK falling edge to LDAC falling edge SCLK rising edge to SDO valid (VDD = 3.6 V to 5.5 V) SCLK rising edge to SDO valid (VDD = 2.5 V to 3.5 V) SCLK falling edge to SYNC rising edge SYNC rising edge to SCLK rising edge SYNC rising edge to LDAC falling edge 3 t1 t2 t3 t4 t5 t6 t7 t8 t9 t10 t11 t12 t13 4, 5 t14 t15 t16 1 Guaranteed by design and characterization; not production tested. All input signals are specified with tR = tF = 5 ns (10% to 90% of VDD) and timed from a voltage level of (VIL + VIH)/2. 3 See Figure 3 and Figure 4. 4 This is measured with the load circuit of Figure 2. t13 determines maximum SCLK frequency in daisy-chain mode. 5 Daisy-chain mode only. 2 Rev. C | Page 5 of 28 AD5307/AD5317/AD5327 2mA VOH (MIN) CL 50pF 2mA 02067-002 TO OUTPUT PIN IOL IOH Figure 2. Load Circuit for Digital Output (SDO) Timing Specifications t1 SCLK t4 t8 t2 t3 t7 SYNC t6 t5 DB15 DIN DB0 t9 t12 LDAC1 t10 LDAC2 t11 CLR 02067-003 NOTES 1ASYNCHRONOUS LDAC UPDATE MODE. 2SYNCHRONOUS LDAC UPDATE MODE. Figure 3. Serial Interface Timing Diagram t1 SCLK t8 t3 t4 t14 t2 SYNC t15 t16 t5 DIN t9 t6 DB0 DB15 INPUT WORD FOR DAC N DB15' DB0' INPUT WORD FOR DAC (N+1) t13 DB0 DB15 SDO UNDEFINED INPUT WORD FOR DAC N Figure 4. Daisy-Chaining Timing Diagram Rev. C | Page 6 of 28 02067-004 LDAC AD5307/AD5317/AD5327 ABSOLUTE MAXIMUM RATINGS TA = 25C, unless otherwise noted. Table 4. Parameter 1 VDD to GND Digital Input Voltage to GND Digital Output Voltage to GND Reference Input Voltage to GND VOUTA - VOUTD to GND Operating Temperature Range Industrial (A, B Versions) Storage Temperature Range Junction Temperature (TJ max) 16-Lead TSSOP Power Dissipation JA Thermal Impedance Reflow Soldering Peak Temperature Time at Peak Temperature 1 Ratings -0.3 V to +7 V -0.3 V to VDD + 0.3 V -0.3 V to VDD + 0.3 V -0.3 V to VDD + 0.3 V -0.3 V to VDD + 0.3 V Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. -40C to +105C -65C to +150C 150C (TJ max - TA)/JA 150.4C/W 220C 10 sec to 40 sec Transient currents of up to 100 mA do not cause SCR latch-up. ESD CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although this product features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality. Rev. C | Page 7 of 28 AD5307/AD5317/AD5327 PIN CONFIGURATION AND FUNCTION DESCRIPTIONS CLR 1 16 SDO LDAC 2 15 SYNC 14 SCLK VDD 3 AD5307/ AD5317/ AD5327 DIN TOP VIEW VOUTB 5 (Not to Scale) 12 GND 13 VOUTC 6 11 VOUTD VREFAB 7 10 PD VREFCD 8 9 DCEN 02067-005 VOUTA 4 Figure 5. Pin Configuration Table 5. Pin Function Descriptions Pin No. 1 2 Mnemonic CLR LDAC 3 VDD 4 5 6 7 VOUTA VOUTB VOUTC VREFAB 8 VREFCD 9 DCEN 10 PD 11 12 13 VOUTD GND DIN 14 SCLK 15 SYNC 16 SDO Description Active Low Control Input. Loads all 0s to all input and DAC registers. Therefore, the outputs also go to 0 V. Active Low Control Input. Transfers the contents of the input registers to their respective DAC registers. Pulsing this pin low allows any or all DAC registers to be updated if the input registers have new data. This allows simultaneous update of all DAC outputs. Alternatively, this pin can be tied permanently low. Power Supply Input. These parts can be operated from 2.5 V to 5.5 V, and the supply should be decoupled with a 10 F capacitor in parallel with a 0.1 F capacitor to GND. Buffered Analog Output Voltage from DAC A. The output amplifier has rail-to-rail operation. Buffered Analog Output Voltage from DAC B. The output amplifier has rail-to-rail operation. Buffered Analog Output Voltage from DAC C. The output amplifier has rail-to-rail operation. Reference Input Pin for DAC A and DAC B. It can be configured as a buffered or unbuffered input to each or both of the DACs, depending on the state of the BUF bits in the serial input words to DAC A and DAC B. It has an input range of 0.25 V to VDD in unbuffered mode and 1 V to VDD in buffered mode. Reference Input Pin for DAC C and DAC D. It can be configured as a buffered or unbuffered input to each or both of the DACs, depending on the state of the BUF bits in the serial input words to DAC C and DAC D. It has an input range of 0.25 V to VDD in unbuffered mode and 1 V to VDD in buffered mode. Enables the Daisy-Chaining Option. It should be tied high if the part is being used in a daisy chain, and tied low if it is being used in standalone mode. Active Low Control Input. It acts like a hardware power-down option. All DACs go into power-down mode when this pin is tied low. The DAC outputs go into a high impedance state, and the current consumption of the part drops to 300 nA @ 5 V (90 nA @ 3 V). Buffered Analog Output Voltage from DAC D. The output amplifier has rail-to-rail operation. Ground Reference Point for All Circuitry on the Part. Serial Data Input. These devices each have a 16-bit shift register. Data is clocked into the register on the falling edge of the serial clock input. The DIN input buffer is powered down after each write cycle. Serial Clock Input. Data is clocked into the input shift register on the falling edge of the serial clock input. Data can be transferred at rates of up to 30 MHz. The SCLK input buffer is powered down after each write cycle. Active Low Control Input. This is the frame synchronization signal for the input data. When SYNC goes low, it powers on the SCLK and DIN buffers and enables the input shift register. Data is transferred in on the falling edges of the following 16 clocks. If SYNC is taken high before the 16th falling edge, the rising edge of SYNC acts as an interrupt and the write sequence is ignored by the device. Serial Data Output. Can be used for daisy-chaining a number of these devices together or for reading back the data in the shift register for diagnostic purposes. The serial data is transferred on the rising edge of SCLK and is valid on the falling edge of the clock. Rev. C | Page 8 of 28 AD5307/AD5317/AD5327 TYPICAL PERFORMANCE CHARACTERISTICS 0.3 1.0 TA = 25C VDD = 5V TA = 25C VDD = 5V 0.2 DNL ERROR (LSB) INL ERROR (LSB) 0.5 0 0.1 0 -0.1 -0.5 0 50 100 150 200 -0.3 250 02067-009 -1.0 02067-006 -0.2 0 50 100 Figure 6. AD5307 INL 250 800 1000 0.6 TA = 25C VDD = 5V 2 TA = 25C VDD = 5V 0.4 1 DNL ERROR (LSB) 0 -1 0 -0.2 -0.4 02067-007 -2 0.2 0 200 400 600 900 -0.6 1000 02067-010 INL ERROR (LSB) 200 Figure 9. AD5307 DNL 3 -3 150 CODE CODE 0 200 400 CODE 600 CODE Figure 7. AD5317 INL Figure 10. AD5317 DNL 1.0 12 TA = 25C VDD = 5V TA = 25C VDD = 5V 8 DNL ERROR (LSB) 0 -4 0 -0.5 -12 0 1000 2000 3000 -1.0 4000 02067-011 -8 02067-008 INL ERROR (LSB) 0.5 4 0 1000 2000 CODE CODE Figure 11. AD5327 DNL Figure 8. AD5327 INL Rev. C | Page 9 of 28 3000 4000 AD5307/AD5317/AD5327 0.2 0.50 TA = 25C VDD = 5V MAX INL 0 0.25 ERROR (% FSR) MAX DNL ERROR (LSB) TA = 25C VREF = 2V 0.1 0 GAIN ERROR -0.1 -0.2 -0.3 MIN INL 0 1 2 3 4 -0.6 5 02067-015 -0.5 02067-012 MIN INL -0.50 OFFSET ERROR -0.4 -0.25 0 1 2 VREF (V) Figure 12. AD5307 INL Error and DNL Error vs. VREF 5 6 5 VDD = 5V VREF = 3V MAX INL 0.3 5V SOURCE 4 0.2 3V SOURCE MAX DNL 0.1 VOUT (V) ERROR (LSB) 4 Figure 15. Offset Error and Gain Error vs. VDD 0.5 0.4 3 VDD (V) 0 -0.1 MIN DNL 3 2 -0.2 -0.3 1 -0.5 -40 0 40 80 0 120 0 1 TEMPERATURE (C) 2 3 4 5 6 SINK/SOURCE CURRENT (mA) Figure 13. AD5307 INL Error and DNL Error vs. Temperature Figure 16. VOUT Source and Sink Current Capability 600 1.0 VDD = 5V VREF = 2V 500 0.5 TA = 25C VDD = 5V VREF = 2V 400 IDD (A) GAIN ERROR 0 300 OFFSET ERROR 200 -0.5 -1.0 -40 0 40 80 120 0 02067-017 100 02067-014 ERROR (% FSR) 3V SINK 5V SINK 02067-016 02067-013 MIN INL -0.4 ZERO SCALE FULL SCALE CODE TEMPERATURE (C) Figure 17. Supply Current vs. DAC Code Figure 14. AD5307 Offset Error and Gain Error vs. Temperature Rev. C | Page 10 of 28 AD5307/AD5317/AD5327 600 -40C +25C 500 TA = 25C VDD = 5V VREF = 5V IDD (A) 400 CH1 +105C VOUTA 300 200 SCLK 2.5 3.0 3.5 4.0 4.5 5.0 CH2 02067-021 0 02067-018 100 5.5 VDD (V) CH1 1V, CH2 5V, TIME BASE = 1s/DIV Figure 21. Half-Scale Settling (1/4 to 3/4 Scale Code Change) Figure 18. Supply Current vs. Supply Voltage 0.5 TA = 25C VDD = 5V VREF = 2V 0.4 IDD (A) CH1 0.3 VDD -40C 0.2 +25C +105C 0 2.5 3.0 3.5 4.0 4.5 5.0 CH2 5.5 VDD (V) CH1 2.00V, CH2 200mV, TIME BASE = 200s/DIV Figure 22. Power-On Reset to 0 V Figure 19. Power-Down Current vs. Supply Voltage 800 VOUTA 02067-022 02067-019 0.1 DECREASING TA = 25C TA = 25C VDD = 5V VREF = 2V 700 IDD (A) INCREASING CH1 600 VDD = 5V VOUTA 500 VDD = 3V DECREASING 300 0 1 2 02067-020 INCREASING 3 4 CH2 PD 02067-023 400 5 VLOGIC (V) CH1 500MV, CH2 5.00V, TIME BASE = 1s/DIV Figure 20. Supply Current vs. Logic Input Voltage for SCLK and DIN Increasing and Decreasing Rev. C | Page 11 of 28 Figure 23. Exiting Power-Down to Midscale AD5307/AD5317/AD5327 0.02 VDD = 5V TA = 25C 02067-024 FREQUENCY FULL-SCALE ERROR (V) VDD = 5V 350 400 450 500 IDD (A) 550 0.01 0 -0.01 -0.02 600 02067-027 VDD = 3V 0 1 2 3 4 5 6 VREF (V) Figure 27. Full-Scale Error vs. VREF Figure 24. IDD Histogram with VDD = 3 V and VDD = 5 V 2.50 1mV/DIV VOUT (V) 2.49 2.47 1s/DIV 150ns/DIV Figure 25. AD5327 Major-Code Transition Glitch Energy Figure 28. DAC-to-DAC Crosstalk 10 0 -10 (dB) -20 -30 -40 02067-026 -50 -60 10 100 1k 10k 02067-028 02067-025 2.48 100k 1M 10M FREQUENCY (Hz) Figure 26. Multiplying Bandwidth (Small-Signal Frequency Response) Rev. C | Page 12 of 28 AD5307/AD5317/AD5327 TERMINOLOGY Relative Accuracy For the DAC, relative accuracy, or integral nonlinearity (INL), is a measure of the maximum deviation in LSB from a straight line passing through the endpoints of the DAC transfer function. Figure 6 through Figure 8 show plots of typical INL vs. code. Differential Nonlinearity Differential nonlinearity (DNL) is the difference between the measured change and the ideal 1 LSB change between any two adjacent codes. A specified differential nonlinearity of 1 LSB maximum ensures monotonicity. This DAC is guaranteed monotonic by design. Figure 9 through Figure 11 show plots of typical DNL vs. code. Offset Error Offset error is a measure of the deviation in the output voltage from 0 V when zero-code is loaded to the DAC (see Figure 29 and Figure 30.) It can be negative or positive. It is expressed in millivolts. Gain Error Gain error is a measure of the span error of the DAC. It is the deviation in slope of the actual DAC transfer characteristic from the ideal expressed as a percentage of the full-scale range. Offset Error Drift Offset error drift is a measure of the change in offset error with changes in temperature. It is expressed in (ppm of fullscale range)/C. Gain Error Drift Gain error drift is a measure of the change in gain error with changes in temperature. It is expressed in (ppm of fullscale range)/C. DC Power Supply Rejection Ratio (PSRR) PSRR indicates how the output of the DAC is affected by changes in the supply voltage. It is the ratio of the change in VOUT to a change in VDD for full-scale output of the DAC. It is measured in decibels. VREF is held at 2 V, and VDD is varied 10%. DC Crosstalk DC crosstalk is the dc change in the output level of one DAC in response to a change in the output of another DAC. It is measured with a full-scale output change on one DAC while monitoring another DAC. It is expressed in microvolts. Reference Feedthrough Reference feedthrough is the ratio of the amplitude of the signal at the DAC output to the reference input when the DAC output is not being updated (that is, LDAC is high). It is expressed in decibels. Channel-to-Channel Isolation Channel-to-channel isolation is the ratio of the amplitude of the signal at the output of one DAC to a sine wave on the reference input of another DAC. It is measured in decibels. Major-Code Transition Glitch Energy Major-code transition glitch energy is the energy of the impulse injected into the analog output when the code in the DAC register changes state. It is normally specified as the area of the glitch in nV-s and is measured when the digital code is changed by 1 LSB at the major carry transition (011 . . . 11 to 100 . . . 00 or 100 . . . 00 to 011 . . . 11). Digital Feedthrough Digital feedthrough is a measure of the impulse injected into the analog output of a DAC from the digital input pins of the device, but it is measured when the DAC is not being written to (SYNC held high). It is specified in nV-s and is measured with a full-scale change on the digital input pins, that is, from all 0s to all 1s or vice versa. Digital Crosstalk Digital crosstalk is the glitch impulse transferred to the output of one DAC at midscale in response to a full-scale code change (all 0s to all 1s or vice versa) in the input register of another DAC. It is measured in standalone mode and is expressed in nV-s. Analog Crosstalk Analog crosstalk is the glitch impulse transferred to the output of one DAC due to a change in the output of another DAC. It is measured by loading one of the input registers with a full-scale code change (all 0s to all 1s or vice versa) while keeping LDAC high, and then pulsing LDAC low and monitoring the output of the DAC whose digital code has not changed. The area of the glitch is expressed in nV-s. DAC-to-DAC Crosstalk DAC-to-DAC crosstalk is the glitch impulse transferred to the output of one DAC due to a digital code change and subsequent output change of another DAC. This includes both digital and analog crosstalk. It is measured by loading one of the DACs with a full-scale code change (all 0s to all 1s or vice versa) with LDAC low while monitoring the output of another DAC. The energy of the glitch is expressed in nV-s. Multiplying Bandwidth The amplifiers within the DAC have a finite bandwidth, and the multiplying bandwidth is a measure of this. A sine wave on the reference (with full-scale code loaded to the DAC) appears on the output. The multiplying bandwidth is the frequency at which the output amplitude falls to 3 dB below the input. Total Harmonic Distortion (THD) THD is the difference between an ideal sine wave and its attenuated version using the DAC. The sine wave is used as the reference for the DAC, and the THD is a measure of the harmonics present on the DAC output. It is measured in decibels. Rev. C | Page 13 of 28 AD5307/AD5317/AD5327 TRANSFER FUNCTION GAIN ERROR + OFFSET ERROR OUTPUT VOLTAGE NEGATIVE OFFSET ERROR DAC CODE ACTUAL IDEAL LOWER DEAD BAND CODES AMPLIFIER FOOTROOM 02067-029 NEGATIVE OFFSET ERROR Figure 29. Transfer Function with Negative Offset GAIN ERROR + OFFSET ERROR UPPER DEADBAND CODES OUTPUT VOLTAGE POSITIVE OFFSET ERROR DAC CODE FULL SCALE Figure 30. Transfer Function with Positive Offset (VREF = VDD) Rev. C | Page 14 of 28 02067-030 ACTUAL IDEAL AD5307/AD5317/AD5327 FUNCTIONAL DESCRIPTION The AD5307/AD5317/AD5327 are quad resistor-string DACs fabricated on a CMOS process with resolutions of 8, 10, and 12 bits respectively. Each contains four output buffer amplifiers and is written to via a 3-wire serial interface. They operate from single supplies of 2.5 V to 5.5 V, and the output buffer amplifiers provide rail-to-rail output swing with a slew rate of 0.7 V/s. DAC A and DAC B share a common reference input, VREFAB. DAC C and DAC D share a common reference input, VREFCD. Each reference input can be buffered to draw virtually no current from the reference source, or can be unbuffered to give a reference input range of 0.25 V to VDD. The devices have a power-down mode in which all DACs can be completely turned off with a high impedance output. DIGITAL-TO-ANALOG SECTION The architecture of one DAC channel consists of a resistorstring DAC followed by an output buffer amplifier. The voltage at the VREF pin provides the reference voltage for the corresponding DAC. Figure 31 shows a block diagram of the DAC architecture. Because the input coding to the DAC is straight binary, the ideal output voltage is given by DAC REFERENCE INPUTS There is a reference pin for each pair of DACs. The reference inputs are buffered but can also be individually configured as unbuffered. The advantage with the buffered input is the high impedance it presents to the voltage source driving it. However, if the unbuffered mode is used, the user can have a reference voltage as low as 0.25 V and as high as VDD, because there is no restriction due to headroom and footroom of the reference amplifier. R R VREF x D 2 R TO OUTPUT AMPLIFIER N where: D is the decimal equivalent of the binary code that is loaded to the DAC register: 0 to 255 for AD5307 (8 bits). 0 to 1023 for AD5317 (10 bits). 0 to 4095 for AD5327 (12 bits). N is the DAC resolution. VREFAB BUF REFERENCE BUFFER RESISTOR STRING R Figure 32. Resistor String If there is a buffered reference in the circuit (for example, REF192), there is no need to use the on-chip buffers of the AD5307/AD5317/ AD5327. In unbuffered mode, the input impedance is still large at typically 90 k per reference input for 0 V to VREF mode and 45 k or 0 V to 2 VREF mode. VOUTA OUTPUT BUFFER AMPLIFIER 02067-031 DAC REGISTER R The buffered/unbuffered option is controlled by the BUF bit in the data-word. The BUF bit setting applies to whichever DAC is selected. GAIN MODE (GAIN = 1 OR 2) INPUT REGISTER The resistor string section is shown in Figure 32. It is simply a string of resistors, each of value R. The digital code loaded to the DAC register determines at which node on the string the voltage is tapped off to be fed into the output amplifier. The voltage is tapped off by closing one of the switches connecting the string to the amplifier. Because it is a string of resistors, it is guaranteed monotonic. 02067-032 VOUT = RESISTOR STRING Figure 31. Single DAC Channel Architecture Rev. C | Page 15 of 28 AD5307/AD5317/AD5327 OUTPUT AMPLIFIER POWER-ON RESET The output buffer amplifier is capable of generating output voltages to within 1 mV of either rail. Its actual range depends on the value of VREF, GAIN, offset error, and gain error. The AD5307/AD5317/AD5327 are each provided with a poweron reset function so that they power up in a defined state. The power-on state is If a gain of 1 is selected (GAIN = 0), the output range is 0.001 V to VREF. * Normal operation * Reference inputs unbuffered * 0 V to VREF output range * Output voltage set to 0 V If a gain of 2 is selected (GAIN = 1), the output range is 0.001 V to 2 VREF. Because of clamping, however, the maximum output is limited to VDD - 0.001 V. The output amplifier is capable of driving a load of 2 k to GND or VDD in parallel with 500 pF to GND or VDD. The source and sink capabilities of the output amplifier can be seen in Figure 16. The slew rate is 0.7 V/s, with a half-scale settling time to 0.5 LSB (at eight bits) of 6 s. Both input and DAC registers are filled with 0s until a valid write sequence is made to the device. This is particularly useful in applications where it is important to know the state of the DAC outputs while the device is powering up. Rev. C | Page 16 of 28 AD5307/AD5317/AD5327 SERIAL INTERFACE The AD5307/AD5317/AD5327 are controlled over versatile 3-wire serial interfaces that operate at clock rates of up to 30 MHz and are compatible with SPI, QSPI, MICROWIRE, and DSP interface standards. The AD5327 uses all 12 bits of DAC data; the AD5317 uses 10 bits and ignores the 2 LSBs. The AD5307 uses eight bits and ignores the last four bits. The data format is straight binary, with all 0s corresponding to 0 V output and all 1s corresponding to full-scale output (VREF - 1 LSB). INPUT SHIFT REGISTER The SYNC input is a level-triggered input that acts as a frame synchronization signal and chip enable. Data can be transferred into the device only while SYNC is low. To start the serial data transfer, SYNC should be taken low, observing the minimum SYNC to SCLK falling edge set-up time, t4. After SYNC goes low, serial data is shifted into the device's input shift register on the falling edges of SCLK for 16 clock pulses. In standalone mode (DCEN = 0), any data and clock pulses after the 16th falling edge of SCLK are ignored, and no further serial data transfer can occur until SYNC is taken high and low again. The input shift register is 16 bits wide. Data is loaded into the device as a 16-bit word under the control of a serial clock input, SCLK. The timing diagram for this operation is shown in Figure 3. The 16-bit word consists of four control bits followed by 8, 10, or 12 bits of DAC data, depending on the device type. Data is loaded MSB first (Bit 15), and the first two bits determine whether the data is for DAC A, DAC B, DAC C, or DAC D. Bit 13 and Bit 12 control the operating mode of the DAC. Bit 13 is GAIN, which determines the output range of the part. Bit 12 is BUF, which controls whether the reference inputs are buffered or unbuffered. SYNC can be taken high after the falling edge of the 16th SCLK pulse, observing the minimum SCLK falling edge to SYNC rising edge time, t7. Table 6. Address Bits for the AD53x7 A1 (Bit 15) 0 0 1 1 A0 (Bit 14) 0 1 0 1 DAC Addressed DAC A DAC B DAC C DAC D After the end of serial data transfer, data is automatically transferred from the input shift register to the input register of the selected DAC. If SYNC is taken high before the 16th falling edge of SCLK, the data transfer is aborted and the DAC input registers are not updated. CONTROL BITS GAIN controls the output range of the addressed DAC. When data has been transferred into the input register of a DAC, the corresponding DAC register and DAC output can be updated by taking LDAC low. CLR is an active low, asynchronous clear that clears the input registers and DAC registers to all 0s. 0: output range of 0 V to VREF. 1: output range of 0 V to 2 VREF. BUF controls whether reference of the addressed DAC is buffered or unbuffered. 0: unbuffered reference. 1: buffered reference. A1 BIT 0 (LSB) A0 GAIN BUF D7 D6 D5 D4 D3 D2 D1 D0 X X X X DATA BITS 02067-033 BIT 15 (MSB) Figure 33. AD5307 Input Shift Register Contents A1 BIT 0 (LSB) A0 GAIN BUF D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 X X DATA BITS 02067-034 BIT 15 (MSB) Figure 34. AD5317 Input Shift Register Contents A1 BIT 0 (LSB) A0 GAIN BUF D11 D10 D9 D8 D7 D6 D5 D4 D3 DATA BITS Figure 35. AD5327 Input Shift Register Contents Rev. C | Page 17 of 28 D2 D1 D0 02067-035 BIT 15 (MSB) AD5307/AD5317/AD5327 LOW POWER SERIAL INTERFACE To minimize the power consumption of the device, the interface powers up fully only when the device is being written to, that is, on the falling edge of SYNC. The SCLK and DIN input buffers are powered down on the rising edge of SYNC. DAISY CHAINING For systems that contain several DACs, or where the user wishes to read back the DAC contents for diagnostic purposes, the SDO pin can be used to daisy-chain several devices together and provide serial readback. By connecting the DCEN (daisy-chain enable) pin high, the daisy-chain mode is enabled. It is tied low in the case of standalone mode. In daisy-chain mode, the internal gating on SCLK is disabled. The SCLK is continuously applied to the input shift register when SYNC is low. If more than 16 clock pulses are applied, the data ripples out of the shift register and appears on the SDO line. This data is clocked out on the rising edge of SCLK and is valid on the falling edge. By connecting this line to the DIN input on the next DAC in the chain, a multi-DAC interface is constructed. Each DAC in the system requires 16 clock pulses; therefore, the total number of clock cycles must equal 16N, where N is the total number of devices in the chain. When the serial transfer to all devices is complete, SYNC should be taken high. This prevents any further data from being clocked into the input shift register. A continuous SCLK source can be used if SYNC is held low for the correct number of clock cycles. Alternatively, a burst clock containing the exact number of clock cycles can be used and SYNC can be taken high some time later. When the transfer to all input registers is complete, a common LDAC signal updates all DAC registers and all analog outputs are updated simultaneously. DOUBLE-BUFFERED INTERFACE The AD5307/AD5317/AD5327 DACs have double-buffered interfaces consisting of two banks of registers: input registers and DAC registers. The input registers are connected directly to the input shift register and the digital code is transferred to the relevant input register on completion of a valid write sequence. The DAC registers contain the digital code used by the resistor strings. Access to the DAC registers is controlled by the LDAC pin. When the LDAC pin is high, the DAC registers are latched and the input registers can change state without affecting the contents of the DAC registers. When LDAC is brought low, however, the DAC registers become transparent and the contents of the input registers are transferred to them. The double-buffered interface is useful if the user requires simultaneous updating of all DAC outputs. The user can write to three of the input registers individually and then, by bringing LDAC low when writing to the remaining DAC input register, all outputs update simultaneously. These parts each contain an extra feature whereby a DAC register is not updated unless its input register has been updated since the last time LDAC was brought low. Normally, when LDAC is brought low, the DAC registers are filled with the contents of the input registers. In the case of the AD5307/AD5317/AD5327, the DAC register updates only if the input register has changed since the last time the DAC register was updated, thereby removing unnecessary digital crosstalk. LOAD DAC INPUT (LDAC) LDAC transfers data from the input registers to the DAC registers and therefore updates the outputs. Use of the LDAC function enables double buffering of the DAC data, GAIN, and BUF. There are two LDAC modes: synchronous and asynchronous. Synchronous Mode In this mode, the DAC registers are updated after new data is read from on the falling edge of the 16th SCLK pulse. LDAC can be tied permanently low or pulsed as in Figure 3. Asynchronous Mode In this mode, the outputs are not updated at the same time that the input registers are written to. When LDAC goes low, the DAC registers are updated with the contents of the input register. POWER-DOWN MODE The AD5307/AD5317/AD5327 have low power consumption, typically dissipating 1.2 mW with a 3 V supply and 2.5 mW with a 5 V supply. Power consumption can be further reduced when the DACs are not in use by putting them into power-down mode, which is selected by taking the PD pin low. When the PD pin is high, all DACs work normally with a typical power consumption of 500 A at 5 V (400 A at 3 V). However, in power-down mode, the supply current falls to 300 nA at 5 V (90 nA at 3 V) when all DACs are powered down. Not only does the supply current drop, but the output stage is also internally switched from the output of the amplifier, making it an open circuit. This has the advantage that the output is three-state while the part is in power-down mode and provides a defined input condition for whatever is connected to the output of the DAC amplifier. The output stage is illustrated in Figure 36. The bias generator, output amplifiers, resistor string, and all other associated linear circuitry are shut down when the powerdown mode is activated. However, the contents of the registers are unaffected when in power-down. In fact, it is possible to load new data to the input registers and DAC registers during power-down. The DAC outputs update as soon as PD goes high. Rev. C | Page 18 of 28 AD5307/AD5317/AD5327 68HC11/68L111 AMPLIFIER PC7 SYNC SCK SCLK MOSI VOUT DIN 02067-036 1ADDITIONAL PINS OMITTED FOR CLARITY. Figure 38. 68HC11/68L11-to-AD5307/AD5317/AD5327 Interface 80C51/80L51-to-AD5307/AD5317/AD5327 Interface Figure 36. Output Stage During Power-Down MICROPROCESSOR INTERFACING ADSP-2101/ADSP-2103-toAD5307/AD5317/AD5327 Interface Figure 37 shows a serial interface between the AD5307/AD5317/ AD5327 and the ADSP-2101/ADSP-2103. The ADSP-2101/ ADSP-2103 should be set up to operate in the SPORT transmit alternate framing mode. The ADSP-2101/ADSP-2103 SPORT is programmed through the SPORT control register and should be configured as follows: internal clock operation, active low framing, 16-bit word length. Transmission is initiated by writing a word to the Tx register after SPORT is enabled. The data is clocked out on each rising edge of the DSP's serial clock and clocked into the AD5307/AD5317/AD5327 on the falling edge of the DAC's SCLK. TFS DT SCLK AD5307/ AD5317/ AD53271 AD5307/ AD5317/ AD53271 80C51/80L511 SYNC DIN P3.3 SYNC SCLK TxD SCLK RxD DIN 1ADDITIONAL PINS OMITTED FOR CLARITY. 02067-037 ADSP-2101/ ADSP-21031 Figure 39 shows a serial interface between the AD5307/AD5317/ AD5327 and the 80C51/80L51 microcontroller. The setup for the interface is as follows: TxD of the 80C51/80L51 drives SCLK of the AD5307/AD5317/AD5327, and RxD drives the serial data line of the part. The SYNC signal is again derived from a bitprogrammable pin on the port. In this case, Port Line P3.3 is used. When data is to be transmitted to the AD5307/AD5317/ AD5327, P3.3 is taken low. The 80C51/80L51 transmits data only in 8-bit bytes; therefore, only eight falling clock edges occur in the transmit cycle. To load data to the DAC, P3.3 is left low after the first eight bits are transmitted, and a second write cycle is initiated to transmit the second byte of data. P3.3 is taken high following the completion of this cycle. The 80C51/80L51 outputs the serial data LSB first. The AD5307/AD5317/AD5327 require their data with the MSB as the first bit received. The 80C51/80L51 transmit routine should take this into account. Figure 37. ADSP-2101/ADSP-2103-to-AD5307/AD5317/AD5327 Interface 1ADDITIONAL PINS OMITTED FOR CLARITY. Figure 39. 80C51/80L51-to-AD5307/AD5317/AD5327 Interface 68HC11/68L11-to-AD5307/AD5317/AD5327 Interface Figure 38 shows a serial interface between the AD5307/AD5317/ AD5327 and the 68HC11/68L11 microcontroller. SCK of the 68HC11/68L11 drives the SCLK of the AD5307/AD5317/ AD5327, and the MOSI output drives the serial data line (DIN) of the DAC. The SYNC signal is derived from a port line (PC7). The set-up conditions for correct operation of this interface are as follows: The 68HC11/68L11 should be configured so that its CPOL bit is 0 and its CPHA bit is 1. When data is being transmitted to the DAC, the SYNC line is taken low (PC7). With this configuration, data appearing on the MOSI output is valid on the falling edge of SCK. Serial data from the 68HC11/68L11 is transmitted in 8-bit bytes, with only eight falling clock edges occurring in the transmit cycle. Data is transmitted MSB first. To load data to the AD5307/AD5317/AD5327, PC7 is left low after the first eight bits are transferred and a second serial write operation is performed to the DAC. PC7 is taken high at the end of this procedure. 02067-039 POWER-DOWN CIRCUITRY MICROWIRE-to-AD5307/AD5317/AD5327 Interface Figure 40 shows an interface between the AD5307/AD5317/ AD5327 and a MICROWIRE-compatible device. Serial data is shifted out on the falling edge of the serial clock, SK, and is clocked into the AD5307/AD5317/AD5327 on the rising edge of SK, which corresponds to the falling edge of the DAC's SCLK. Rev. C | Page 19 of 28 AD5307/ AD5317/ AD53271 MICROWIRE1 CS SYNC SK SCLK SO DIN 1ADDITIONAL PINS OMITTED FOR CLARITY. 02067-040 RESISTOR STRING DAC AD5307/ AD5317/ AD53271 02067-038 The time to exit power-down is typically 2.5 s for VDD = 5 V and 5 s when VDD = 3 V. This is the time from the rising edge of PD to when the output voltage deviates from its power-down voltage. See Figure 23 for a plot. Figure 40. MICROWIRE-to-AD5307/AD5317/AD5327 Interface AD5307/AD5317/AD5327 APPLICATIONS TYPICAL APPLICATION CIRCUIT BIPOLAR OPERATION The AD5307/AD5317/AD5327 can be used with a wide range of reference voltages and offer full, one-quadrant multiplying capability over a reference range of 0.25 V to VDD. More typically, these devices are used with a fixed precision reference voltage. Suitable references for 5 V operation are the AD780 and REF192 (2.5 V references). For 2.5 V operation, a suitable external reference would be the AD589, a 1.23 V band gap reference. Figure 41 shows a typical setup for the AD5307/AD5317/AD5327 when using an external reference. The AD5307/AD5317/AD5327 are designed for single-supply operation, but a bipolar output range is also possible using the circuit shown in Figure 42. This circuit provides an output voltage range of 5 V. Rail-to-rail operation at the amplifier output is achievable by using an AD820 or an OP295 as the output amplifier. The output voltage for any input code can be calculated as follows: (REFIN x D / 2 N )x (R1 + R2) VOUT = - REFIN x (R2 / R1) R1 VDD = 2.5V TO 5.5V 10F 0.1F VOUT EXT REF 1F VREF AB VOUTA VREF CD VOUTB where: D is the decimal equivalent of the code loaded to the DAC. N is the DAC resolution. REFIN is the reference voltage input. AD5307/AD5317/ AD5327 AD780/REF192 WITH VDD = 5V OR AD589 WITH VDD = 2.5V SCLK VOUTC DIN SYNC When REFIN = 5 V, R1 = R2 = 10 k, VOUTD GND 02067-041 SERIAL INTERFACE VOUT = (10 x D/2N) - 5 V Figure 41. AD5307/AD5317/AD5327 Using a 2.5 V External Reference R1 10k +6V TO +16V DRIVING VDD FROM THE REFERENCE VOLTAGE 10F If an output range of 0 V to VDD is required when the reference inputs are configured as unbuffered, the simplest solution is to connect the reference input to VDD. Because this supply can be noisy and not very accurate, the AD5307/AD5317/AD5327 can be powered from the reference voltage, for example, from a 5 V reference such as the REF195, which outputs a steady supply voltage. The typical current required from the REF195 with no load on the DAC outputs is 500 A supply current and 112 A into the reference inputs (if unbuffered). When the DAC outputs are loaded, the REF195 also needs to supply the current to the loads. The total current required with a 10 k load on each output is R2 10k +5V 0.1F 5V VDD VOUTA AD5307/AD5317/ AD5327 VIN REF195 VOUT GND 612 A + 4 (5 V/10 k) = 2.6 mA The load regulation of the REF195 is typically 2 ppm/mA, which results in an error of 5.2 ppm (26 V) for the 2.6 mA current drawn from it. This corresponds to a 0.0013 LSB error at eight bits and a 0.021 LSB error at 12 bits. Rev. C | Page 20 of 28 +5V 1F VREF AB VREF CD AD820/ OP295 -5V VOUTB VOUTC VOUTD GND DIN SCLK SYNC SERIAL INTERFACE Figure 42. Bipolar Operation with the AD5307/AD5317/AD5327 02067-042 VIN AD5307/AD5317/AD5327 AD5307 The AD5307/AD5317/AD5327 each have a versatile 3-wire serial interface, making them ideal for generating accurate voltages in process-control and industrial applications. Due to noise, safety requirements, or distance, it may be necessary to isolate the AD5307/AD5317/AD5327 from the controller. This can easily be achieved by using opto-isolators capable of providing isolation in excess of 3 kV. The actual data rate achieved can be limited by the type of optocouplers chosen. The serial loading structure of the AD5307/AD5317/AD5327 makes them ideally suited for use in opto-isolated applications. Figure 43 shows an opto-isolated interface to the AD5307/AD5317/AD5327 where DIN, SCLK, and SYNC are driven from optocouplers. The power supply to the part should also be isolated. This is done by using a transformer. On the DAC side of the transformer, a 5 V regulator provides the 5 V supply required for the AD5307/AD5317/ AD5327. 10F 0.1F 10k SCLK VDD VREF AB VREF CD AD5307 VDD 10k SYNC VOUTA SYNC VDD VCC ENABLE CODED ADDRESS 1G 74HC139 1A AD5307 1Y0 1Y1 1Y2 1Y3 1B DGND AD5307 AD5307 Figure 44. Decoding Multiple AD5307 Devices in a System AD5307/AD5317/AD5327 AS DIGITALLY PROGRAMMABLE WINDOW DETECTORS 5V 0.1F VREF VOUTD 10F VIN 1k DIN DIN SCLK 02067-043 GND SYNC FAIL VDD VREF AB AD5307/ AD5317/ SYNC AD5327 1/2 CMP04 SCLK GND VOUTB Figure 45. Window Detection The SYNC pin on the AD5307/AD5317/AD5327 can be used in applications to decode a number of DACs. In this application, all DACs in the system receive the same serial clock and serial data, but the SYNC to only one of the devices is active at any given time, allowing access to four channels in this 16-channel system. The 74HC139 is used as a 2-to-4 line decoder to address any of the DACs in the system. To prevent timing errors, the enable input should be brought to its inactive state while the coded address inputs are changing state. Figure 44 shows a diagram of a typical setup for decoding multiple AD5307 devices in a system. Rev. C | Page 21 of 28 PASS PASS/FAIL DIN Figure 43. AD5307 in an Opto-Isolated Interface DECODING MULTIPLE AD5307/AD5317/AD5327 DEVICES 1k VOUTA VREF CD 10k DCEN VOUTA VOUTB VOUTC VOUTD SYNC DIN SCLK VOUTC DIN VOUTA VOUTB VOUTC VOUTD SYNC DIN SCLK VOUTB VDD VOUTA VOUTB VOUTC VOUTD SYNC DIN SCLK A digitally programmable upper/lower limit detector using two of the DACs in the AD5307/AD5317/AD5327 is shown in Figure 45. The upper and lower limits for the test are loaded to DAC A and DAC B, which, in turn, set the limits on the CMP04. If the signal at the VIN input is not within the programmed window, an LED indicates the fail condition. Similarly, DAC C and DAC D can be used for window detection on a second VIN signal. VDD SCLK DIN SYNC DIN SCLK 1/6 74HC05 02067-045 5V REGULATOR POWER VOUTA VOUTB VOUTC VOUTD SCLK 02067-044 OPTO-ISOLATED INTERFACE FOR PROCESS-CONTROL APPLICATIONS AD5307/AD5317/AD5327 DAISY CHAINING POWER SUPPLY BYPASSING AND GROUNDING For systems that contain several DACs, or where the user wishes to read back the DAC contents for diagnostic purposes, the SDO pin can be used to daisy-chain several devices together and provide serial readback. Figure 4 shows the timing diagram for daisy-chain applications. The daisy-chain mode is enabled by connecting DCEN high (see Figure 46). In any circuit where accuracy is important, careful consideration of the power supply and ground return layout helps to ensure the rated performance. The printed circuit board on which the AD5307/AD5317/AD5327 are mounted should be designed so that the analog and digital sections are separated and confined to certain areas of the board. If the AD5307/AD5317/AD5327 are in a system where multiple devices require an AGND-toDGND connection, the connection should be made at one point only. The star ground point should be established as close as possible to the device. The AD5307/AD5317/AD5327 should have ample supply bypassing of 10 F in parallel with 0.1 F on the supply located as close to the package as possible, ideally right up against the device. The 10 F capacitors are the tantalum bead type. The 0.1 F capacitor should have low effective series resistance (ESR) and low effective series inductance (ESI), such as is typical of the common ceramic types that provide a low impedance path to ground at high frequencies to handle transient currents due to internal logic switching. 68HC111 MOSI AD53071 DIN SCK SCLK PC7 SYNC PC6 LDAC DCEN SDO MISO DIN AD53071 SCLK SYNC LDAC DCEN SDO DIN AD53071 SCLK SYNC DCEN SDO 1ADDITIONAL PINS OMITTED FOR CLARITY. Figure 46. AD5307 in Daisy-Chain Mode 02067-046 LDAC The power supply lines of the AD5307/AD5317/AD5327 should use as large a trace as possible to provide low impedance paths and reduce the effects of glitches on the power supply line. Components, such as clocks, with fast switching signals should be shielded with digital ground to avoid radiating noise to other parts of the board, and they should never be run near the reference inputs. Avoid crossover of digital and analog signals. Traces on opposite sides of the board should run at right angles to each other. This reduces the effects of feedthrough on the board. A microstrip technique is by far the best, but it is not always possible with a double-sided board. In this technique, the component side of the board is dedicated to ground plane, and signal traces are placed on the solder side. Rev. C | Page 22 of 28 AD5307/AD5317/AD5327 Table 7. Overview of AD53xx Serial Devices 1 Part No. SINGLES AD5300 AD5310 AD5320 AD5301 AD5311 AD5321 DUALS AD5302 AD5312 AD5322 AD5303 AD5313 AD5323 QUADS AD5304 AD5314 AD5324 AD5305 AD5315 AD5325 AD5306 AD5316 AD5326 AD5307 AD5317 AD5327 OCTALS AD5308 AD5318 AD5328 1 Resolution No. of DACs DNL Interface Settling Time (s) Package Pin 8 10 12 8 10 12 1 1 1 1 1 1 0.25 0.5 1.0 0.25 0.5 1.0 SPI SPI SPI 2-Wire 2-Wire 2-Wire 4 6 8 6 7 8 SOT-23, MSOP SOT-23, MSOP SOT-23, MSOP SOT-23, MSOP SOT-23, MSOP SOT-23, MSOP 6, 8 6, 8 6, 8 6, 8 6, 8 6, 8 8 10 12 8 10 12 2 2 2 2 2 2 0.25 0.5 1.0 0.25 0.5 1.0 SPI SPI SPI SPI SPI SPI 6 7 8 6 7 8 MSOP MSOP MSOP TSSOP TSSOP TSSOP 8 8 8 16 16 16 8 10 12 8 10 12 8 10 12 8 10 12 4 4 4 4 4 4 4 4 4 4 4 4 0.25 0.5 1.0 0.25 0.5 1.0 0.25 0.5 1.0 0.25 0.5 1.0 SPI SPI SPI 2-Wire 2-Wire 2-Wire 2-Wire 2-Wire 2-Wire SPI SPI SPI 6 7 8 6 7 8 6 7 8 6 7 8 MSOP MSOP MSOP MSOP MSOP MSOP TSSOP TSSOP TSSOP TSSOP TSSOP TSSOP 10 10 10 10 10 10 16 16 16 16 16 16 8 10 12 8 8 8 0.25 0.5 1.0 SPI SPI SPI 6 7 8 TSSOP TSSOP TSSOP 16 16 16 Visit www.analog.com/support/standard_linear/selection_guides/AD53xx.html for more information. Table 8. Overview of AD53xx Parallel Devices Part No. SINGLES AD5330 AD5331 AD5340 AD5341 DUALS AD5332 AD5333 AD5342 AD5343 QUADS AD5334 AD5335 AD5336 AD5344 Resolution DNL VREF Pin Settling Time (s) BUF 8 10 12 12 0.25 0.5 1.0 1.0 1 1 1 1 6 7 8 8 * 8 10 12 12 0.25 0.5 1.0 1.0 2 2 2 1 6 7 8 8 8 10 10 12 0.25 0.5 0.5 1.0 2 2 4 4 6 7 7 8 Additional Pin Functions GAIN HBEN CLR * * * * * * * * * * Package Pin * * * * * TSSOP TSSOP TSSOP TSSOP 20 20 24 20 * * * * * TSSOP TSSOP TSSOP TSSOP 20 24 28 20 * * * TSSOP TSSOP TSSOP TSSOP 24 24 28 28 * * * Rev. C | Page 23 of 28 AD5307/AD5317/AD5327 OUTLINE DIMENSIONS 5.10 5.00 4.90 16 9 4.50 4.40 4.30 6.40 BSC 1 8 PIN 1 1.20 MAX 0.15 0.05 0.65 BSC 0.30 0.19 COPLANARITY 0.10 0.20 0.09 SEATING PLANE 8 0 COMPLIANT TO JEDEC STANDARDS MO-153-AB Figure 47. 16-Lead Thin Shrink Small Outline Package [TSSOP] (RU-16) Dimensions shown in millimeters Rev. C | Page 24 of 28 0.75 0.60 0.45 AD5307/AD5317/AD5327 ORDERING GUIDE Model Temperature Range Package Description Package Option AD5307ARU AD5307ARU-REEL7 AD5307ARUZ1 AD5307ARUZ-REEL71 AD5307BRU AD5307BRU-REEL AD5307BRU-REEL7 AD5307BRUZ1 AD5307BRUZ-REEL1 AD5307BRUZ-REEL71 AD5317ARU AD5317ARU-REEL7 AD5317ARUZ1 AD5317BRU AD5317BRU-REEL AD5317BRU-REEL7 AD5317BRUZ1 AD5317BRUZ-REEL1 AD5317BRUZ-REEL71 AD5327ARU AD5327ARU-REEL7 AD5327ARUZ1 AD5327BRU AD5327BRU-REEL AD5327BRU-REEL7 AD5327BRUZ1 AD5327BRUZ-REEL1 AD5327BRUZ-REEL71 -40C to +105C -40C to +105C -40C to +105C -40C to +105C -40C to +105C -40C to +105C -40C to +105C -40C to +105C -40C to +105C -40C to +105C -40C to +105C -40C to +105C -40C to +105C -40C to +105C -40C to +105C -40C to +105C -40C to +105C -40C to +105C -40C to +105C -40C to +105C -40C to +105C -40C to +105C -40C to +105C -40C to +105C -40C to +105C -40C to +105C -40C to +105C -40C to +105C 16-Lead Thin Shrink Small Outline Package [TSSOP] 16-Lead Thin Shrink Small Outline Package [TSSOP] 16-Lead Thin Shrink Small Outline Package [TSSOP] 16-Lead Thin Shrink Small Outline Package [TSSOP] 16-Lead Thin Shrink Small Outline Package [TSSOP] 16-Lead Thin Shrink Small Outline Package [TSSOP] 16-Lead Thin Shrink Small Outline Package [TSSOP] 16-Lead Thin Shrink Small Outline Package [TSSOP] 16-Lead Thin Shrink Small Outline Package [TSSOP] 16-Lead Thin Shrink Small Outline Package [TSSOP] 16-Lead Thin Shrink Small Outline Package [TSSOP] 16-Lead Thin Shrink Small Outline Package [TSSOP] 16-Lead Thin Shrink Small Outline Package [TSSOP] 16-Lead Thin Shrink Small Outline Package [TSSOP] 16-Lead Thin Shrink Small Outline Package [TSSOP] 16-Lead Thin Shrink Small Outline Package [TSSOP] 16-Lead Thin Shrink Small Outline Package [TSSOP] 16-Lead Thin Shrink Small Outline Package [TSSOP] 16-Lead Thin Shrink Small Outline Package [TSSOP] 16-Lead Thin Shrink Small Outline Package [TSSOP] 16-Lead Thin Shrink Small Outline Package [TSSOP] 16-Lead Thin Shrink Small Outline Package [TSSOP] 16-Lead Thin Shrink Small Outline Package [TSSOP] 16-Lead Thin Shrink Small Outline Package [TSSOP] 16-Lead Thin Shrink Small Outline Package [TSSOP] 16-Lead Thin Shrink Small Outline Package [TSSOP] 16-Lead Thin Shrink Small Outline Package [TSSOP] 16-Lead Thin Shrink Small Outline Package [TSSOP] RU-16 RU-16 RU-16 RU-16 RU-16 RU-16 RU-16 RU-16 RU-16 RU-16 RU-16 RU-16 RU-16 RU-16 RU-16 RU-16 RU-16 RU-16 RU-16 RU-16 RU-16 RU-16 RU-16 RU-16 RU-16 RU-16 RU-16 RU-16 1 Z = Pb-free part. Rev. C | Page 25 of 28 AD5307/AD5317/AD5327 NOTES Rev. C | Page 26 of 28 AD5307/AD5317/AD5327 NOTES Rev. C | Page 27 of 28 AD5307/AD5317/AD5327 NOTES (c)2006 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. C02067-0-3/06(C) Rev. C | Page 28 of 28